TI SN74AVCH20T245GR

SCES567F − MAY 2004 − REVISED APRIL 2005
D Control Inputs VIH/VIL Levels are
D
D
D
D
D
D
D
D
D
DGG OR DGV PACKAGE
(TOP VIEW)
Referenced to VCCA Voltage
VCC Isolation Feature − If Either VCC Input
Is at GND, Both Ports Are in the
High-Impedance State
Overvoltage-Tolerant Inputs/Outputs Allow
Mixed-Voltage-Mode Data Communications
Fully Configurable Dual-Rail Design Allows
Each Port to Operate Over the Full 1.2-V to
3.6-V Power-Supply Range
Ioff Supports Partial-Power-Down Mode
Operation
I/Os Are 4.6-V Tolerant
Bus Hold on Data Inputs Eliminates the
Need for External Pullup/Pulldown
Resistors
Max Data Rates
− 380 Mbps (1.8-V to 3.3-V Translation)
− 260 Mbps (< 1.8-V to 3.3-V Translation)
− 260 Mbps (Translate to 2.5 V)
− 210 Mbps (Translate to 1.8 V)
− 120 Mbps (Translate to 1.5 V)
− 100 Mbps (Translate to 1.2 V)
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Protection Exceeds JESD 22
− 8000-V Human-Body Model (A114-A)
− 200-V Machine Model (A115-A)
− 1000-V Charged-Device Model (C101)
1DIR
1B1
1B2
GND
1B3
1B4
VCCB
1B5
1B6
1B7
GND
1B8
1B9
1B10
2B1
2B2
2B3
GND
2B4
2B5
2B6
VCCB
2B7
2B8
GND
2B9
2B10
2DIR
1
56
2
55
3
54
4
53
5
52
6
51
7
50
8
49
9
48
10
47
11
46
12
45
13
44
14
43
15
42
16
41
17
40
18
39
19
38
20
37
21
36
22
35
23
34
24
33
25
32
26
31
27
30
28
29
1OE
1A1
1A2
GND
1A3
1A4
VCCA
1A5
1A6
1A7
GND
1A8
1A9
1A10
2A1
2A2
2A3
GND
2A4
2A5
2A6
VCCA
2A7
2A8
GND
2A9
2A10
2OE
description/ordering information
This 20-bit noninverting bus transceiver uses two separate configurable power-supply rails. The
SN74AVCH20T245 is optimized to operate with VCCA/VCCB set at 1.4 V to 3.6 V. It is operational with VCCA/VCCB
as low as 1.2 V. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The
B port is designed to track VCCB. VCCB accepts any supply voltage from 1.2 V to 3.6 V. This allows for universal
low-voltage bidirectional translation between any of the 1.2-V, 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes.
ORDERING INFORMATION
−40°C to 85°C
ORDERABLE
PART NUMBER
PACKAGE†
TA
TOP-SIDE
MARKING
TSSOP − DGG
Tape and reel
SN74AVCH20T245GR
AVCH20T245
TVSOP − DGV
Tape and reel
SN74AVCH20T245VR
WK245
VFBGA − GQL
SN74AVCH20T245KR
VFBGA − ZQL (Pb-free)
Tape and reel
74AVCH20T245ZQLR
WK245
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available
at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2005, Texas Instruments Incorporated
!"#$ % &'!!($ #% )'*+&#$ ,#$(!,'&$% &!" $ %)(&&#$% )(! $.( $(!"% (/#% %$!'"($%
%$#,#!, 0#!!#$1- !,'&$ )!&(%%2 ,(% $ (&(%%#!+1 &+',(
$(%$2 #++ )#!#"($(!%-
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCES567F − MAY 2004 − REVISED APRIL 2005
description/ordering information (continued)
The SN74AVCH20T245 is designed for asynchronous communication between data buses. The device
transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the
direction-control (DIR) input. The output-enable (OE) input can be used to disable the outputs so that the buses
are effectively isolated.
The SN74AVCH20T245 is designed so that the control (1DIR, 2DIR, 1OE, and 2OE) inputs are supplied by
VCCA.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
The VCC isolation feature ensures that if either VCC input is at GND, both outputs are in the high-impedance
state. The bus-hold circuitry on the powered-up side always stays active.
Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors
with the bus-hold circuitry is not recommended.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
GQL OR ZQL PACKAGE
(TOP VIEW)
1
2
3
4
5
6
terminal assignments
1
2
3
4
5
6
A
A
1B1
1B2
1DIR
1OE
1A2
1A1
B
B
1B3
1B4
GND
GND
1A4
1A3
C
1B5
1B6
1A5
1B7
1B8
VCCA
GND
1A6
D
VCCB
GND
E
1B9
1B10
C
D
E
F
G
1A7
1A9
F
2B1
2B2
2A2
2A1
G
2B3
2B4
GND
GND
2A4
2A3
H
2B5
2B6
VCCA
GND
2A6
2A5
2A8
2A7
2OE
2A10
2A9
H
J
2B7
2B8
VCCB
GND
J
K
2B9
2B10
2DIR
K
FUNCTION TABLE
(each 10-bit section)
INPUTS
OE
2
1A8
1A10
DIR
OPERATION
L
L
B data to A bus
L
H
A data to B bus
H
X
Isolation
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCES567F − MAY 2004 − REVISED APRIL 2005
logic diagram (positive logic)
1DIR
1
2DIR
56
1A1
29
1OE
55
2A1
2
28
2OE
42
15
1B1
2B1
To Nine Other Channels
To Nine Other Channels
Pin numbers shown are for the DGG and DGV packages.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCCA and VCCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Input voltage range, VI (see Note 1): I/O ports (A port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
I/O ports (B port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Control inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Voltage range applied to any output in the high-impedance or power-off state, VO
(see Note 1): (A port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
(B port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Voltage range applied to any output in the high or low state, VO
(see Notes 1 and 2): (A port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCCA + 0.5 V
(B port) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCCB + 0.5 V
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Continuous current through each VCCA, VCCB, and GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 3): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64°C/W
DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48°C/W
GQL/ZQL package . . . . . . . . . . . . . . . . . . . . . . . . . . . 42°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input voltage and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.
2. The output positive-voltage rating may be exceeded up to 4.6 V maximum if the output current rating is observed.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCES567F − MAY 2004 − REVISED APRIL 2005
recommended operating conditions (see Notes 4 through 8)
VCCI
VCCA
VCCB
VCCO
MIN
MAX
Supply voltage
1.2
3.6
V
Supply voltage
1.2
3.6
V
VCCI × 0.65
1.6
1.2 V to 1.95 V
High-level input
voltage
VIH
Data inputs
(see Note 7)
1.95 V to 2.7 V
2.7 V to 3.6 V
VIL
Data inputs
(see Note 7)
VCCI × 0.35
0.7
1.95 V to 2.7 V
2.7 V to 3.6 V
High-level input
voltage
VIH
Low-level input
voltage
VIL
VI
DIR
(referenced to VCCA)
(see Note 8)
DIR
(referenced to VCCA)
(see Note 8)
Output voltage
IOH
VCCA ×0.65
1.6
1.2 V to 1.95 V
1.95 V to 2.7 V
2.7 V to 3.6 V
VCCA × 0.35
0.7
1.95 V to 2.7 V
2.7 V to 3.6 V
0
3.6
V
0
3-state
0
VCCO
3.6
V
1.2 V
−3
1.4 V to 1.6 V
−6
1.65 V to 1.95 V
−8
2.3 V to 2.7 V
−9
3 V to 3.6 V
−12
1.2 V
3
1.4 V to 1.6 V
6
1.65 V to 1.95 V
8
2.3 V to 2.7 V
9
3 V to 3.6 V
12
Input transition rise or fall rate
TA
NOTES: 4.
5.
6.
V
0.8
Active state
Low-level output current
∆t/∆v
V
2
1.2 V to 1.95 V
High-level output current
IOL
V
0.8
Input voltage
VO
V
2
1.2 V to 1.95 V
Low-level input
voltage
UNIT
Operating free-air temperature
−40
mA
mA
5
ns/V
85
°C
VCCI is the VCC associated with the data input port.
VCCO is the VCC associated with the output port.
All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
7. For VCCI values not specified in the data sheet, VIH(min) = VCCI x 0.7 V, VIL(max) = VCCI x 0.3 V.
8. For VCCI values not specified in the data sheet, VIH(min) = VCCA x 0.7 V, VIL(max) = VCCA x 0.3 V.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCES567F − MAY 2004 − REVISED APRIL 2005
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Note 9)
PARAMETER
TEST CONDITIONS
1.2 V to 3.6 V
1.2 V to 3.6 V
1.2 V
1.2 V
1.4 V
1.4 V
1.05
1.65 V
1.65 V
1.2
IOH = −9 mA
IOH = −12 mA
2.3 V
2.3 V
1.75
3V
3V
2.3
IOL = 100 µA
IOL = 3 mA
1.2 V to 3.6 V
1.2 V to 3.6 V
1.2 V
1.2 V
IOH = −6 mA
IOH = −8 mA
IOL = 6 mA
IOL = 8 mA
VOL
VI = VIH
II
IBHL†
IBHH‡
IBHHO¶
MIN
MAX
VCCO − 0.2 V
V
0.2
0.15
1.4 V
0.35
1.65 V
0.45
2.3 V
2.3 V
0.55
3V
3V
0.7
1.2 V to 3.6 V
1.2 V to 3.6 V
VI = 0.42 V
VI = 0.49 V
1.2 V
1.2 V
1.4 V
1.4 V
15
VI = 0.58 V
VI = 0.7 V
1.65 V
1.65 V
25
2.3 V
2.3 V
45
VI = 0.8 V
VI = 0.78 V
3.3 V
3.3 V
100
1.2 V
1.2 V
VI = 0.91 V
VI = 1.07 V
1.4 V
1.4 V
−15
1.65 V
1.65 V
−25
2.3 V
2.3 V
−45
3.3 V
3.3 V
−100
1.2 V
1.2 V
1.6 V
1.6 V
125
1.95 V
1.95 V
200
2.7 V
2.7 V
300
3.6 V
3.6 V
1.2 V
1.2 V
VI = VCCA or GND
VI = 0 to VCC
VI = 0 to VCC
UNIT
0.95
1.4 V
VI = 1.6 V
VI = 2 V
IBHLO§
MIN
1.65 V
VI = VIL
IOL = 9 mA
IOL = 12 mA
Control
inputs
−40°C to 85°C
VCCB
IOH = −100 µA
IOH = −3 mA
VOH
TA = 25°C
TYP
MAX
VCCA
±0.025
±0.25
±1
V
µA
25
µA
−25
µA
50
µA
500
−50
1.6 V
1.6 V
−125
1.95 V
1.95 V
−200
2.7 V
2.7 V
−300
3.6 V
3.6 V
−500
µA
† The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and
then raising it to VIL max.
‡ The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and
then lowering it to VIH min.
§ An external driver must source at least IBHLO to switch this node from low to high.
¶ An external driver must sink at least IBHHO to switch this node from high to low.
NOTE 9: VCCO is the VCC associated with the output port.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SCES567F − MAY 2004 − REVISED APRIL 2005
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Notes 10 and 11) (continued)
PARAMETER
TEST CONDITIONS
B port
A or B
ports
IOZ†
B port
Cio
A or B
ports
−40°C to 85°C
MIN
MAX
UNIT
±0.1
±1
±5
0V
±0.1
±1
±5
OE = VIH
3.6 V
3.6 V
±0.5
±2.5
±5
OE =
don’t care
0V
3.6 V
±5
3.6 V
0V
±5
1.2 V to 3.6 V
1.2 V to 3.6 V
35
0V
3.6 V
−5
3.6 V
0V
35
1.2 V to 3.6 V
1.2 V to 3.6 V
35
0V
3.6 V
35
3.6 V
0V
−5
1.2 V to 3.6 V
1.2 V to 3.6 V
65
VI = 3.3 V or GND
3.3 V
3.3 V
3.5
pF
VO = 3.3 V or GND
3.3 V
3.3 V
7
pF
VO = VCCO or
GND,
VI = VCCI or GND
VI = VCCI or GND,
ICCA ) ICCB
Control
Ci
inputs
TA = 25°C
TYP
MAX
0 to 3.6 V
VI = VCCI or GND,
ICCB
MIN
0V
VI or VO = 0 to 3.6 V
A port
ICCA
VCCB
0 to 3.6 V
A port
Ioff
VCCA
VI = VCCI or GND,
IO = 0
IO = 0
IO = 0
µA
A
A
µA
µA
µA
µA
† For I/O ports, the parameter IOZ includes the input leakage current.
NOTES: 10. VCCO is the VCC associated with the output port.
11. VCCI is the VCC associated with the input port.
switching characteristics over recommended operating free-air temperature range,
VCCA = 1.2 V (see Figure 1)
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
A
B
tPLH
tPHL
B
A
tPZH
tPZL
OE
A
tPZH
tPZL
OE
B
tPHZ
tPLZ
OE
A
tPHZ
tPLZ
OE
B
PARAMETER
6
VCCB = 1.2 V
TYP
VCCB = 1.5 V
TYP
VCCB = 1.8 V
TYP
VCCB = 2.5 V
TYP
VCCB = 3.3 V
TYP
3.8
3.1
2.8
2.7
3.3
3.8
3.1
2.8
2.7
3.3
4.1
3.8
3.6
3.5
3.4
4.1
3.8
3.6
3.5
3.4
6.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
5.6
4.4
3.8
3.3
3.2
5.6
4.4
3.8
3.3
3.2
6.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
5.7
4.6
4.7
4.1
5.4
5.7
4.6
4.7
4.1
5.4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
ns
ns
ns
ns
ns
ns
SCES567F − MAY 2004 − REVISED APRIL 2005
switching characteristics over recommended operating free-air temperature range,
VCCA = 1.5 V ± 0.1 V (see Figure 1)
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
A
B
tPLH
tPHL
B
A
tPZH
tPZL
OE
A
tPZH
tPZL
OE
B
tPHZ
tPLZ
OE
A
tPHZ
tPLZ
OE
B
PARAMETER
VCCB = 1.2 V
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
TYP
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
3.8
0.5
6.4
0.5
5.4
0.5
4.3
0.5
3.9
3.8
0.5
6.4
0.5
5.4
0.5
4.3
0.5
3.9
3.1
0.5
6.4
0.5
6.1
0.5
5.8
0.5
5.7
3.1
0.5
6.4
0.5
6.1
0.5
5.8
0.5
5.7
4.3
1.5
10.3
1.5
10.3
1.5
10.2
1.5
10.2
4.3
1.5
10.3
1.5
10.3
1.5
10.2
1.5
10.2
5.2
1
10.3
1
8.4
0.5
6.1
0.5
5.3
5.2
1
10.3
1
8.4
0.5
6.1
0.5
5.3
4.5
2
9
2
9
2
9
2
9
4.5
2
9
2
9
2
9
2
9
5.1
1.5
9
1.5
7.8
1
6.4
1
5.9
5.1
1.5
9
1.5
7.8
1
6.4
1
5.9
UNIT
ns
ns
ns
ns
ns
ns
switching characteristics over recommended operating free-air temperature range,
VCCA = 1.8 V ± 0.15 V (see Figure 1)
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
A
B
tPLH
tPHL
B
A
tPZH
tPZL
OE
A
tPZH
tPZL
OE
B
tPHZ
tPLZ
OE
A
tPHZ
tPLZ
OE
B
PARAMETER
VCCB = 1.2 V
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
TYP
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
3.6
0.5
6.1
0.5
5
0.5
3.9
0.5
3.5
3.6
0.5
6.1
0.5
5
0.5
3.9
0.5
3.5
2.8
0.5
5.4
0.5
5
0.5
4.7
0.5
4.6
2.8
0.5
5.4
0.5
5
0.5
4.7
0.5
4.6
3.4
1
8.1
1
7.9
1
7.9
1
7.9
3.4
1
8.1
1
7.9
1
7.9
1
7.9
5
0.5
10
0.5
7.9
0.5
5.7
0.5
4.8
5
0.5
10
0.5
7.9
0.5
5.7
0.5
4.8
4.1
2
7.4
2
7.4
2
7.4
2
7.4
4.1
2
7.4
2
7.4
2
7.4
2
7.4
4.9
1.5
8.7
1.5
7.4
1
5.8
1
5.1
4.9
1.5
8.7
1.5
7.4
1
5.8
1
5.1
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
ns
ns
ns
ns
ns
ns
7
SCES567F − MAY 2004 − REVISED APRIL 2005
switching characteristics over recommended operating free-air temperature range,
VCCA = 2.5 V ± 0.2 V (see Figure 1)
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
A
B
tPLH
tPHL
B
A
tPZH
tPZL
OE
A
tPZH
tPZL
OE
B
tPHZ
tPLZ
OE
A
tPHZ
tPLZ
OE
B
PARAMETER
VCCB = 1.2 V
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
TYP
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
3.5
0.5
5.8
0.5
4.7
0.5
3.5
0.5
3
3.5
0.5
5.8
0.5
4.7
0.5
3.5
0.5
3
2.7
0.5
4.3
0.5
3.9
0.5
3.5
0.5
3.4
2.7
0.5
4.3
0.5
3.9
0.5
3.5
0.5
3.4
2.5
0.5
5.4
0.5
5.3
0.5
5.2
0.5
5.2
2.5
0.5
5.4
0.5
5.3
0.5
5.2
0.5
5.2
4.8
0.5
9.6
0.5
7.6
0.5
5.3
0.5
4.3
4.8
0.5
9.6
0.5
7.6
0.5
5.3
0.5
4.3
3
1.1
5.2
1.1
5.2
1.1
5.2
1.1
5.2
3
1.1
5.2
1.1
5.2
1.1
5.2
1.1
5.2
4.7
1.2
8.2
1.2
6.9
1
5.3
1
5
4.7
1.2
8.2
1.2
6.9
1
5.3
1
5
UNIT
ns
ns
ns
ns
ns
ns
switching characteristics over recommended operating free-air temperature range,
VCCA = 3.3 V ± 0.3 V (see Figure 1)
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
A
B
tPLH
tPHL
B
A
tPZH
tPZL
OE
A
tPZH
tPZL
OE
B
tPHZ
tPLZ
OE
A
tPHZ
tPLZ
OE
B
PARAMETER
8
VCCB = 1.2 V
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
TYP
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
3.4
0.5
5.7
0.5
4.6
0.5
3.4
0.5
2.9
3.4
0.5
5.7
0.5
4.6
0.5
3.4
0.5
2.9
3.3
0.5
3.9
0.5
3.5
0.5
3
0.5
2.9
3.3
0.5
3.9
0.5
3.5
0.5
3
0.5
2.9
2.2
0.5
4.4
0.5
4.3
0.5
4.2
0.5
4.1
2.2
0.5
4.4
0.5
4.3
0.5
4.2
0.5
4.1
4.7
1
9.6
0.5
7.5
0.5
5.1
0.5
4.1
4.7
1
9.6
0.5
7.5
0.5
5.1
0.5
4.1
3.4
0.8
5
0.8
5
0.8
5
0.8
5
3.4
0.8
5
0.8
5
0.8
5
0.8
5
4.6
1.2
8.1
1.2
6.7
1
5.1
0.8
5
4.6
1.2
8.1
1.2
6.7
1
5.1
0.8
5
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
ns
ns
ns
ns
ns
ns
SCES567F − MAY 2004 − REVISED APRIL 2005
operating characteristics, TA = 25°C
VCCA =
VCCB = 1.2 V
VCCA =
VCCB = 1.5 V
VCCA =
VCCB = 1.8 V
VCCA =
VCCB = 2.5 V
VCCA =
VCCB = 3.3 V
TYP
TYP
TYP
TYP
TYP
1
1
1
1
2
1
1
1
1
1
12
13
14
15
16
Outputs
Disabled
1
1
1
1
1
Outputs
Enabled
13
13
14
15
16
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
PARAMETER
TEST
CONDITIONS
Outputs
Enabled
A to B
CpdA†
Outputs
Disabled
Outputs
Enabled
B to A
A to B
CpdB†
Outputs
Disabled
Outputs
Enabled
B to A
CL = 0,
f = 10 MHz,
tr = tf =1 ns
UNIT
pF
CL = 0,
f = 10 MHz,
tr = tf =1 ns
pF
Outputs
Disabled
† Power-dissipation capacitance per transceiver
typical total static power consumption (ICCA + ICCB)
TABLE 1
VCCA
VCCB
0V
1.2 V
1.5 V
1.8 V
2.5 V
3.3 V
0V
0
< 0.5
< 0.5
< 0.5
< 0.5
< 0.5
1.2 V
< 0.5
<1
<1
<1
<1
1
1.5 V
< 0.5
<1
<1
<1
<1
1
1.8 V
< 0.5
<1
<1
<1
<1
<1
2.5 V
< 0.5
1
<1
<1
<1
<1
3.3 V
< 0.5
1
<1
<1
<1
<1
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
UNIT
A
µA
9
SCES567F − MAY 2004 − REVISED APRIL 2005
TYPICAL CHARACTERISTICS
6
6
5
5
4
4
tPHL − ns
tPLH − ns
TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE
TA = 25°C, VCCA = 1.2 V
3
2
2
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.8 V
1
3
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.8 V
1
VCCB = 2.5 V
VCCB = 3.3 V
0
0
10
20
30
40
50
VCCB = 2.5 V
VCCB = 3.3 V
0
60
0
10
20
CL − pF
30
40
50
60
CL − pF
Figure 1
Figure 2
6
6
5
5
4
4
tPHL − ns
tPLH − ns
TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE
TA = 25°C, VCCA = 1.5 V
3
2
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.8 V
1
3
2
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.8 V
1
VCCB = 2.5 V
VCCB = 3.3 V
0
0
10
20
30
40
50
60
VCCB = 2.5 V
VCCB = 3.3 V
0
0
10
CL − pF
30
CL − pF
Figure 3
10
20
Figure 4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
40
50
60
SCES567F − MAY 2004 − REVISED APRIL 2005
6
6
5
5
4
4
tPHL − ns
tPLH − ns
TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE
TA = 25°C, VCCA = 1.8 V
3
2
2
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.8 V
1
3
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.8 V
1
VCCB = 2.5 V
VCCB = 3.3 V
0
0
10
20
30
40
50
VCCB = 2.5 V
VCCB = 3.3 V
0
60
0
10
20
CL − pF
30
40
50
60
40
50
60
CL − pF
Figure 5
Figure 6
TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE
TA = 25°C, VCCA = 2.5 V
6
6
5
5
4
VCCB = 2.5 V
VCCB = 3.3 V
4
tPHL − ns
tPLH − ns
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.8 V
3
2
VCCB = 1.2 V
VCCB = 1.5 V
1
VCCB = 1.8 V
3
2
1
VCCB = 2.5 V
VCCB = 3.3 V
0
0
10
20
30
40
50
60
0
0
10
CL − pF
20
30
CL − pF
Figure 7
Figure 8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SCES567F − MAY 2004 − REVISED APRIL 2005
TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE
TA = 25°C, VCCA = 3.3 V
6
6
5
5
4
VCCB = 2.5 V
VCCB = 3.3 V
4
tPHL − ns
tPLH − ns
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.8 V
3
2
3
2
VCCB = 1.2 V
VCCB = 1.5 V
1
VCCB = 1.8 V
VCCB = 2.5 V
VCCB = 3.3 V
0
0
10
20
30
40
50
60
1
0
0
10
CL − pF
30
CL − pF
Figure 9
12
20
Figure 10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
40
50
60
SCES567F − MAY 2004 − REVISED APRIL 2005
PARAMETER MEASUREMENT INFORMATION
2 × VCCO
S1
RL
From Output
Under Test
Open
GND
CL
(see Note A)
TEST
S1
tpd
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCCO
GND
RL
tw
LOAD CIRCUIT
VCCI
VCCI/2
Input
VCCO
1.2 V
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
CL
RL
15 pF
15 pF
15 pF
15 pF
15 pF
2 kΩ
2 kΩ
2 kΩ
2 kΩ
2 kΩ
VTP
0.1 V
0.1 V
0.15 V
0.15 V
0.3 V
VCCI/2
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VCCA
Output
Control
(low-level
enabling)
VCCA/2
0V
tPLZ
tPZL
VCCI
Input
VCCI/2
VCCI/2
0V
tPLH
Output
VOH
VCCO/2
VOL
VCCO/2
VCCO
Output
Waveform 1
S1 at 2 × VCCO
(see Note B)
tPHL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VCCA/2
VCCO/2
VOL
tPHZ
tPZH
Output
Waveform 2
S1 at GND
(see Note B)
VOL + VTP
VCCO/2
VOH − VTP
VOH
0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRRv10 MHz, ZO = 50 Ω, dv/dt ≥ 1 V/ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. VCCI is the VCC associated with the input port.
I. VCCO is the VCC associated with the output port.
Figure 11. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
PACKAGE OPTION ADDENDUM
www.ti.com
6-Dec-2006
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
74AVCH20T245GRE4
ACTIVE
TSSOP
DGG
56
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
74AVCH20T245VRE4
ACTIVE
TVSOP
DGV
56
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
74AVCH20T245ZQLR
ACTIVE
BGA MI
CROSTA
R JUNI
OR
ZQL
56
1000 Green (RoHS &
no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
SN74AVCH20T245GR
ACTIVE
TSSOP
DGG
56
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74AVCH20T245KR
ACTIVE
BGA MI
CROSTA
R JUNI
OR
GQL
56
1000
SNPB
Level-1-240C-UNLIM
SN74AVCH20T245VR
ACTIVE
TVSOP
DGV
56
2000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TBD
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,40
0,23
0,13
24
13
0,07 M
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–8°
1
0,75
0,50
12
A
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,08
14
16
20
24
38
48
56
A MAX
3,70
3,70
5,10
5,10
7,90
9,80
11,40
A MIN
3,50
3,50
4,90
4,90
7,70
9,60
11,20
DIM
4073251/E 08/00
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUARY 1998
DGG (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
48 PINS SHOWN
0,27
0,17
0,50
48
0,08 M
25
6,20
6,00
8,30
7,90
0,15 NOM
Gage Plane
1
0,25
24
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
48
56
64
A MAX
12,60
14,10
17,10
A MIN
12,40
13,90
16,90
DIM
4040078 / F 12/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power Wireless www.ti.com/lpw
Mailing Address:
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2006, Texas Instruments Incorporated