HITTITE HMC369LP3

MICROWAVE CORPORATION
HMC369LP3
v01.0604
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
FREQ. MULTIPLIERS - SMT
11
Typical Applications
Features
Active Multiplier for X Band Applications:
Output Power: +4 dBm
• OC-192 Clock Recovery
Sub-Harmonic Suppression: 30 dBc
• Microwave Radio & VSAT
SSB Phase Noise: -142 dBc/Hz
• Military Radios, Radar & ECM
Single Supply: [email protected] 46 mA
• Test Instrumentation
9 mm2 Leadless SMT Package
Functional Diagram
General Description
The HMC369LP3 is an active miniature x2 frequency
multiplier utilizing InGaP GaAs HBT technology in a
3 mm x 3 mm leadless QFN surface mount package.
Power output is +4 dBm typical from a single +5.0V
supply and varies little vs. input power, temperature
and supply voltage. Suppression of undesired
fundamental and sub-harmonics is 30 dBc typical
with respect to output signal level. The low additive
SSB phase noise of -142 dBc/Hz at 100 kHz
offset helps the user maintain good system noise
performance. The HMC369LP3 is ideal for use in
LO multiplier chains allowing reduced parts count
versus traditional approaches. The HMC369LP3
is also useful for OC-192 clock recovery. The
application of 10 GBPS data to the input generates
a -7 dBm clock tone at the output with spurious
signals suppressed by 25 dB.
Electrical Specifications, TA = +25° C, Vcc= 5.0V
Parameter
Typ.
Max.
Min.
Typ.
Max.
Units
Frequency Range, Input
4.95 - 5.3
5.3 - 6.35
GHz
Frequency Range, Output
9.9 - 10.6
10.6 - 12.7
GHz
Input Power Range
-5
Output Power
-1
+5
3
-5
0
+5
dBm
4
dBm
Sub-Harmonic Suppression
30
30
dBc
Input Return Loss
17
16
dB
Output Return Loss
5.5
6
dB
-142
-142
dBc/Hz
46
46
mA
SSB Phase Noise (100 kHz Offset)
Supply Current (Icc)
11 - 40
Min.
Pin= 0 dBm
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
HMC369LP3
v01.0604
MICROWAVE CORPORATION
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
8
8
7
7
6
6
OUTPUT POWER (dBm)
5
4
3
2
1
+25 C
0
+85 C
-40 C
-1
-2
9.5
10
10.5
11
11.5
5
4
3
2
1
-10 dBm
-5 dBm
0 dBm
+5 dBm
0
-1
12
12.5
-2
9.5
13
GHz
10
OUTPUT FREQUENCY (GHz)
10.5
11
11.5
11
12
12.5
13
OUTPUT FREQUENCY (GHz)
Output Power vs.
Supply Voltage @ 0 dBm Drive Level
Input Return Loss vs. Temperature
0
8
INPUT RETURN LOSS (dB)
6
5
4
3
2
1
Vcc=4.5V
Vcc=5.0V
Vcc=5.5V
0
-1
-2
9.5
-5
+25 C
+85 C
-40 C
-10
-15
-20
-25
-30
10
10.5
11
11.5
12
12.5
13
3
3.5
4
4.5
5
5.5
FREQUENCY (GHz)
OUTPUT FREQUENCY (GHz)
6
Output Return Loss vs. Temperature
6.5
7
0
OUTPUT RETURN LOSS (dB)
OUTPUT POWER (dBm)
7
FREQ. MULTIPLIERS - SMT
OUTPUT POWER (dBm)
Output Power vs.
GaAs MMIC
SUB-HARMONICALLY
PUMPED
MIXER
- 25
Output
Power
vs. Drive17
Level
Temperature
@ 0 dBm
Drive Level
-1
-2
+25 C
+85 C
-40 C
-3
-4
-5
-6
-7
-8
-9
-10
9.5
10
10.5
11
11.5
12
12.5
13
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
11 - 41
MICROWAVE CORPORATION
HMC369LP3
v01.0604
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
SSB Phase Noise
Performance, Fout= 10.66 GHz,
Input Power= 0 dBm
Output Spectrum
10
SSB PHASE NOISE (dBc/Hz)
11
OUTPUT POWER (dBm)
0
-10
-20
-30
-40
-50
-60
0
2
4
6
8
10
12
14 16 18
26
3
10
4
10
5
10
11 - 42
6
10
OFFSET FREQUENCY (Hz)
FREQ. MULTIPLIERS - SMT
FREQUENCY (GHz)
20 22 24
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
-150
-160
2
10
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
7
10
MICROWAVE CORPORATION
HMC369LP3
v01.0604
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
Absolute Maximum Ratings
+20 dBm
Vcc (V)
Icc (mA)
Vcc
+6.0V
4.5
45
Channel Temperature
150 °C
5.0
46
Continuous Pdiss (T=85 °C)
(derate 7 mW/°C above 85 °C)
450 mW
5.5
47
Thermal Resistance (Rth)
(junction to ground paddle)
145 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
Note: Multiplier will operate over full voltage range
shown above.
11
FREQ. MULTIPLIERS - SMT
RF Input (Vcc= +5V)
Typical Supply Current vs. Vcc
Pin Locations & Outline Drawing
NOTES:
1. MATERIAL PACKAGE BODY: LOW STRESS INJECTION MOLDED
PLASTIC SILICA AND SILICON IMPREGNATED.
2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY
3. LEAD AND GROUND PADDLE PLATING: Sn/Pb SOLDER
4. DIMENSIONS ARE IN INCHES [MILLIMETERS].
5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
6. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
7. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
8. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED
TO PCB RF GROUND.
9. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB
LAND PATTERN.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
11 - 43
MICROWAVE CORPORATION
HMC369LP3
v01.0604
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
Pin Description
FREQ. MULTIPLIERS - SMT
11
11 - 44
Pin Number
Function
Description
1, 2, 5-8, 1113, 15, 16
N/C
No Connection. These pins may be connected to RF
ground if desired. Performance will not be affected.
3
RF IN
RF input needs to be DC blocked only if there is an
external DC voltage applied to RF IN.
4, 9
GND
All ground leads and ground paddle must be soldered
to PCB RF/DC ground.
10
RF OUT
Multiplied Output. AC coupled. No external DC blocks
necessary.
14
Vcc
Supply voltage 5V ± 0.5V.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
MICROWAVE CORPORATION
v01.0604
HMC369LP3
SMT GaAs HBT MMIC x2 ACTIVE
FREQUENCY MULTIPLIER, 9.9 - 12.7 GHz OUTPUT
Evaluation PCB
The circuit board used in the final application should be generated with proper RF circuit design techniques.
Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be
connected directly to the ground plane similar to that shown. The evaluation circuit board shown is available from
Hittite upon request.
List of Materials
Item
Description
J1, J2
PC Mount SMA Connector
J3, J4
DC Pin
C1
0.01 µF Capacitor, 0603 Pkg.
U1
HMC369LP3, x2 Active Multiplier
PCB*
107710 Eval Board
FREQ. MULTIPLIERS - SMT
11
* Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
11 - 45