TL1963A-xx www.ti.com........................................................................................................................................................ SLVS719E – JUNE 2008 – REVISED AUGUST 2009 1.5-A LOW-NOISE FAST-TRANSIENT-RESPONSE LOW-DROPOUT REGULATOR FEATURES 1 • • • • • • • DCQ PACKAGE (TOP VIEW) GND Optimized for Fast Transient Response Output Current: 1.5 A Dropout Voltage: 340 mV Low Noise: 40 μVRMS (10 Hz to 100 kHz) 1-mA Quiescent Current No Protection Diodes Needed Controlled Quiescent Current in Dropout Fixed Output Voltages: 1.5 V, 1.8 V, 2.5 V, and 3.3 V Adjustable Output Voltage: 1.21 V to 20 V Less Than 1-μA Quiescent Current in Shutdown Stable with 10-μF Output Capacitor Stable with Ceramic Capacitors Reverse-Battery Protection No Reverse Current Thermal Limiting 5 4 3 2 1 6 SENSE/ADJ OUT GND IN SHDN DCY PACKAGE (TOP VIEW) GND • • • • • • • • 2 4 3 OUT 2 GND 1 IN KTT PACKAGE (TOP VIEW) 5 4 3 2 1 SENSE/ADJ OUT GND IN SHDN APPLICATIONS • • 3.3-V to 2.5-V Logic Power Supplies Post Regulator for Switching Supplies DESCRIPTION/ORDERING INFORMATION The TL1963A-xx is a low-dropout (LDO) regulator optimized for fast transient response. The device can supply 1.5 A of output current with a dropout voltage of 340 mV. Operating quiescent current is 1 mA, dropping to less than 1 μA in shutdown. Quiescent current is well controlled; it does not rise in dropout as it does with many other regulators. In addition to fast transient response, the TL1963A-xx regulators have very low output noise, which makes them ideal for sensitive RF supply applications. Output voltage range is from 1.21 V to 20 V. The TL1963A-xx regulators are stable with output capacitors as low as 10 μF. Small ceramic capacitors can be used without the necessary addition of ESR, as is common with other regulators. Internal protection circuitry includes reverse-battery protection, current limiting, thermal limiting, and reverse-current protection. The devices are available in fixed output voltages of 1.5 V, 1.8 V, 2.5 V, and 3.3 V, and as an adjustable device with a 1.21-V reference voltage. The TL1963A-xx regulators are available in the 5-pin TO-263 (KTT), 6-pin TO-223 (DCQ), and 3-pin SOT-223 (DCY) packages. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD, PowerFLEX are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2008–2009, Texas Instruments Incorporated TL1963A-xx SLVS719E – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com ORDERING INFORMATION (1) VOUT (TYP) TA PACKAGE 1.5 V 1.8 V –40°C to 125°C 2.5 V 3.3 V ADJ (1) (2) (2) ORDERABLE PART NUMBER TOP-SIDE MARKING TO-263 – KTT Reel of 500 TL1963A-15KTTR TL1963A-15 TO-223 – DCQ Reel of 2500 TL1963A-15DCQR 1963A-15 SOT-223 – DCY Reel of 2500 TL1963A-15DCYR TF TO-263 – KTT Reel of 500 TL1963A-18KTTR TL1963A-18 TO-223 – DCQ Reel of 2500 TL1963A-18DCQR 1963A-18 SOT-223 – DCY Reel of 2500 TL1963A-18DCYR TG TO-263 – KTT Reel of 500 TL1963A-25KTTR TL1963A-25 TO-223 – DCQ Reel of 2500 TL1963A-25DCQR 1963A-25 SOT-223 – DCY Reel of 2500 TL1963A-25DCYR TH TO-263 – KTT Reel of 500 TL1963A-33KTTR TL1963A-33 TO-223 – DCQ Reel of 2500 TL1963A-33DCQR 1963A-33 SOT-223 – DCY Reel of 2500 TL1963A-33DCYR TJ TO-263 – KTT Reel of 500 TL1963AKTTR TL1963A TO-223 – DCQ Reel of 2500 TL1963ADCQR TL1963A For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. Table 1. TERMINAL FUNCTIONS NAME SHDN 2 NO. DCQ 1 DCY — DESCRIPTION KTT 1 Shutdown. The SHDN pin is used to put the TL1963A-xx regulators into a low-power shutdown state. The output is off when the SHDN pin is pulled low. The SHDN pin can be driven either by 5-V logic or open-collector logic with a pullup resistor. The pullup resistor is required to supply the pullup current of the open-collector gate, normally several microamperes, and the SHDN pin current, typically 3 μA. If unused, the SHDN pin must be connected to VIN. The device is in the low-power shutdown state if the SHDN pin is not connected. IN 2 1 2 Input. Power is supplied to the device through the IN pin. A bypass capacitor is required on this pin if the device is more than six inches away from the main input filter capacitor. In general, the output impedance of a battery rises with frequency, so it is advisable to include a bypass capacitor in battery-powered circuits. A bypass capacitor (ceramic) in the range of 1 μF to 10 μF is sufficient. The TL1963A-xx regulators are designed to withstand reverse voltages on the IN pin with respect to ground and the OUT pin. In the case of a reverse input, which can happen if a battery is plugged in backwards, the device acts as if there is a diode in series with its input. There is no reverse current flow into the regulator, and no reverse voltage appears at the load. The device protects both itself and the load. GND 3, 6 2, 4 3 Ground OUT 4 3 4 Output. The output supplies power to the load. A minimum output capacitor (ceramic) of 10 μF is required to prevent oscillations. Larger output capacitors are required for applications with large transient loads to limit peak voltage transients. ADJ 5 — 5 Adjust. For the adjustable TL1963A, this is the input to the error amplifier. This pin is clamped internally to ±7 V. It has a bias current of 3 μA that flows into the pin. The ADJ pin voltage is 1.21 V referenced to ground, and the output voltage range is 1.21 V to 20 V. 5 Sense. For fixed voltage versions of the TL1963A-xx (TL1963A-1.5, TL1963A-1.8, TL1963A-2.5, and TL1963A-3.3), the SENSE pin is the input to the error amplifier. Optimum regulation is obtained at the point where the SENSE pin is connected to the OUT pin of the regulator. In critical applications, small voltage drops are caused by the resistance (RP) of PC traces between the regulator and the load. These may be eliminated by connecting the SENSE pin to the output at the load as shown in Figure 32. Note that the voltage drop across the external PC traces adds to the dropout voltage of the regulator. The SENSE pin bias current is 600 μA at the rated output voltage. The SENSE pin can be pulled below ground (as in a dual supply system in which the regulator load is returned to a negative supply) and still allow the device to start and operate. SENSE 5 — Thermal Pad — — Submit Documentation Feedback For the KTT package, the exposed thermal pad is connected to ground and must be soldered to the PCB for rated thermal performance. Copyright © 2008–2009, Texas Instruments Incorporated TL1963A-xx www.ti.com........................................................................................................................................................ SLVS719E – JUNE 2008 – REVISED AUGUST 2009 ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) IN –20 V to 20 V OUT VIN –20 V to 20 V Input-to-output differential Input voltage range (2) –20 V to 20 V SENSE –20 V to 20 V ADJ –7 V to 7 V SHDN –20 V to 20 V tshort Output short-circuit duration Tlead Maximum lead temperature TJ Operating virtual-junction temperature range –40°C to 125°C Tstg Storage temperature range –65°C to 150°C (1) (2) Indefinite 10-second soldering time 300°C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Absolute maximum input-to-output differential voltage cannot be achieved with all combinations of rated IN pin and OUT pin voltages. With the IN pin at 20 V, the OUT pin may not be pulled below 0 V. The total measured voltage from IN to OUT cannot exceed ±20 V. PACKAGE THERMAL DATA (1) (1) (2) θJP (2) PACKAGE BOARD θJA θJC SOT-223 (DCY) High K, JESD 51-5 48.3°C/W 30.6°C/W TO-223 (DCQ) High K, JESD 51-5 53°C/W 15°C/W — TO-263 (KTT) High K, JESD 51-5 26.5°C/W 24.1°C/W 0.38°C/W — Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability. For packages with exposed thermal pads, such as QFN, PowerPAD™, and PowerFLEX™, θJP is defined as the thermal resistance between the die junction and the bottom of the exposed pad. Copyright © 2008–2009, Texas Instruments Incorporated Submit Documentation Feedback 3 TL1963A-xx SLVS719E – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com ELECTRICAL CHARACTERISTICS (1) Over operating temperature range TJ = –40°C to 125°C (unless otherwise noted) PARAMETER TEST CONDITIONS Minimum input voltage VIN (3) (4) Full range 2.1 2.5 25°C 1.477 1.500 1.523 Full range 1.447 1.500 1.545 25°C 1.773 1.800 1.827 Full range 1.737 1.800 1.854 25°C 2.462 2.500 2.538 Full range 2.412 2.500 2.575 25°C 3.250 3.300 3.350 Full range 3.200 3.300 3.400 25°C 1.192 1.21 1.228 VIN = 2.5 V to 20 V, ILOAD = 1 mA to 1.5 A Full range 1.174 1.21 1.246 TL1963A-1.5 ΔVIN = 2.21 V to 20 V, ILOAD = 1 mA Full range 2 6 TL1963A-1.8 ΔVIN = 2.3 V to 20 V, ILOAD = 1 mA Full range 2.5 7 TL1963A-2.5 ΔVIN = 3 V to 20 V, ILOAD = 1 mA Full range 3 10 TL1963A-3.3 ΔVIN = 3.8 V to 20 V, ILOAD = 1 mA Full range 3.5 10 TL1963A (3) ΔVIN = 2.21 V to 20 V, ILOAD = 1 mA Full range 1.5 5 TL1963A-1.5 VIN = 2.5 V, ΔILOAD = 1 mA to 1.5 A TL1963A-1.8 VIN = 2.8 V, ΔILOAD = 1 mA to 1.5 A Regulated output voltage (5) VIN = 2.5 V to 20 V, ILOAD = 1 mA to 1.5 A VIN = 2.8 V to 20 V, ILOAD = 1 mA to 1.5 A VIN = 3 V, ILOAD = 1 mA TL1963A-2.5 VIN = 3.5 V to 20 V, ILOAD = 1 mA to 1.5 A VIN = 3.8 V, ILOAD = 1 mA TL1963A-3.3 VIN = 4.3 V to 20 V, ILOAD = 1 mA to 1.5 A VIN = 2.21 V, ILOAD = 1 mA Line regulation Load regulation TL1963A (2) (3) (4) (5) 4 25°C 25°C 25°C Full range TL1963A-3.3 VIN = 4.3 V, ΔILOAD = 1 mA to 1.5 A Full range 25°C 25°C Full range UNIT V V V mV 9 18 2 Full range VIN = 3.5 V, ΔILOAD = 1 mA to 1.5 A VIN = 2.5 V, ΔILOAD = 1 mA to 1.5 A 2 Full range TL1963A-2.5 TL1963A (3) (1) MAX ILOAD = 1.5 A VIN = 2.3 V, ILOAD = 1 mA (5) (2) 1.9 TL1963A-1.8 ADJ pin voltage (3) TYP 25°C VIN = 2.21 V, ILOAD = 1 mA VADJ MIN ILOAD = 0.5 A TL1963A-1.5 VOUT TJ 10 20 2.5 15 30 3 mV 20 70 2 8 18 The TL1963A-xx regulators are tested and specified under pulse load conditions such that TJ TA. The TL1963A-xx is fully tested at TA = 25°C. Performance at –40°C and 125°C is specified by design, characterization, and correlation with statistical process controls. Typical values represent the likely parametric nominal values determined at the time of characterization. Typical values depend on the application and configuration and may vary over time. Typical values are not ensured on production material. The TL1963A (adjustable version) is tested and specified for these conditions with the ADJ pin connected to the OUT pin. For the TL1963A, TL1963A-1.5 and TL1963A-1.8, dropout voltages are limited by the minimum input voltage specification under some output voltage/load conditions. Operating conditions are limited by maximum junction temperature. The regulated output voltage specification does not apply for all possible combinations of input voltage and output current. When operating at maximum input voltage, the output current range must be limited. When operating at maximum output current, the input voltage range must be limited. Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated TL1963A-xx www.ti.com........................................................................................................................................................ SLVS719E – JUNE 2008 – REVISED AUGUST 2009 ELECTRICAL CHARACTERISTICS (1) (continued) Over operating temperature range TJ = –40°C to 125°C (unless otherwise noted) PARAMETER TEST CONDITIONS VDROPOUT Output voltage noise IADJ ADJ pin bias current (3) I SHDN 0.27 0.34 Full range 0.45 0.55 ILOAD = 0 mA Full range 1 1.5 ILOAD = 1 mA Full range 1.1 1.6 ILOAD = 100 mA Full range 3.8 5.5 ILOAD = 500 mA Full range 15 25 ILOAD = 1.5 A Full range 80 120 25°C 40 25°C Full range VOUT = ON to OFF Full range 0.25 3 10 0.9 2 0.75 25°C 0.01 1 V SHDN = 20 V 25°C 3 30 Quiescent current in shutdown VIN = 6 V, V SHDN = 0 V 25°C 0.01 1 Ripple rejection VIN – VOUT = 1.5 V (avg), VRIPPLE = 0.5 VP-P, fRIPPLE = 120 Hz, ILOAD = 0.75 A 25°C IIL Input reverse leakage current Reverse output current (10) VIN = 7 V, VOUT = 0 V 55 25°C VIN = VOUT(NOMINAL) + 1 Full range VIN = –20 V, VOUT = 0 V Full range mA μVRMS V SHDN = 0 V Current limit V 0.35 25°C VOUT = OFF to ON UNIT 0.17 0.22 0.19 Full range (9) SHDN pin current ILIMIT IRO 0.1 25°C COUT = 10 μF, ILOAD = 1.5 A, BW = 10 Hz to 100 kHz Shutdown threshold 0.06 Full range ILOAD = 1.5 A eN MAX 0.02 0.1 25°C ILOAD = 100 mA Dropout voltage VIN = VOUT(NOMINAL) GND pin current (7) (8) VIN = VOUT(NOMINAL) + 1 (2) TYP Full range ILOAD = 500 mA IGND MIN 25°C ILOAD = 1 mA (4) (6) (7) TJ 63 μA V μA μA dB 2 A 1.6 1 TL1963A-1.5 VOUT = 1.5 V, VIN < 1.5 V 25°C 600 1200 TL1963A-1.8 VOUT = 1.8 V, VIN < 1.8 V 25°C 600 1200 TL1963A-2.5 VOUT = 2.5 V, VIN < 2.5 V 25°C 600 1200 TL1963A-3.3 VOUT = 3.3 V, VIN < 3.3 V 25°C 600 1200 TL1963A VOUT = 1.21 V, VIN < 1.21 V 25°C 300 600 mA μA (6) Dropout voltage is the minimum input to output voltage differential needed to maintain regulation at a specified output current. In dropout, the output voltage is equal to: VIN – VDROPOUT. (7) To satisfy requirements for minimum input voltage, the TL1963A (adjustable version) is tested and specified for these conditions with an external resistor divider (two 4.12-kΩ resistors) for an output voltage of 2.4 V. The external resistor divider adds a 300-mA DC load on the output. (8) GND pin current is tested with VIN = (VOUT(NOMINAL) + 1 V) and a current source load. The GND pin current decreases at higher input voltages. (9) ADJ pin bias current flows into the ADJ pin. (10) Reverse output current is tested with the IN pin grounded and the OUT pin forced to the rated output voltage. This current flows into the OUT pin and out the GND pin. Copyright © 2008–2009, Texas Instruments Incorporated Submit Documentation Feedback 5 TL1963A-xx SLVS719E – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com TYPICAL CHARACTERISTICS DROPOUT VOLTAGE vs OUTPUT CURRENT DROPOUT VOLTAGE vs TEMPERATURE 500 480 450 IOUT = 1.5 A 400 Dropout Voltage – mV Dropout Voltage – mV 360 350 TA = 125°C 300 250 200 TA = 25°C 150 240 IOUT = 0.5 A IOUT = 100 mA 120 100 50 IOUT = 1 mA 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 0 -50 1.6 -25 0 Output Current – A 75 100 125 Figure 2. QUIESCENT CURRENT vs TEMPERATURE OUTPUT VOLTAGE vs TEMPERATURE 100 125 1.84 VIN = 6 V 1.4 1.3 VTL1963A-1.8 OUT Fixed 1.8 V IIOUT OUT = 1 mA 1.83 IOUT = 0 A VSHDN = VIN 1.82 1.2 1.1 Output Voltage – V Quiescent Current – mA 50 Figure 1. 1.5 VOUT Fixed 3.3 V TL1963A-3.3 1 0.9 VOUT Adjustable TL1963A (Adjustable) 0.8 1.81 1.8 1.79 1.78 0.7 1.77 0.6 0.5 -50 1.76 -25 0 25 50 75 TA – Free-Air Temperature – °C Figure 3. 6 25 TA – Free-Air Temperature – °C Submit Documentation Feedback 100 125 -50 -25 0 25 50 75 TA – Free-Air Temperature – °C Figure 4. Copyright © 2008–2009, Texas Instruments Incorporated TL1963A-xx www.ti.com........................................................................................................................................................ SLVS719E – JUNE 2008 – REVISED AUGUST 2009 TYPICAL CHARACTERISTICS (continued) OUTPUT VOLTAGE vs TEMPERATURE OUTPUT VOLTAGE vs TEMPERATURE 2.58 2.56 3.38 VOUT Fixed 2.5 V TL1963A-2.5 IIOUT = 1 mA OUT = 1 mA 3.34 Output Voltage – V 2.54 Output Voltage – V VTL1963A-3.3 OUT Fixed 3.3 V IOUT = 1 mA IOUT 3.36 2.52 2.5 2.48 3.32 3.3 3.28 2.46 3.26 2.44 3.24 2.42 -50 3.22 -25 0 25 50 75 100 -50 125 -25 0 Figure 5. Figure 6. OUTPUT VOLTAGE vs TEMPERATURE QUIESCENT CURRENT vs INPUT VOLTAGE 1.23 100 125 TJ = 25°C VOUT Adjustable TL1963A (Adjustable) IIOUT = 1 mA OUT = 1 mA VIN V V IN = 6 V ROUT = 4.3 k W 1 1.215 1.21 1.205 1.2 VSHDN = VIN VOUT Adjustable TL1963A (Adjustable) 0.8 0.6 0.4 0.2 1.195 1.19 -50 75 1.2 Quiescent Current – mA Output Voltage – V 1.22 50 TA – Free-Air Temperature – °C TA – Free-Air Temperature – °C 1.225 25 0 -25 0 25 50 75 TA – Free-Air Temperature – °C Figure 7. Copyright © 2008–2009, Texas Instruments Incorporated 100 125 0 2 4 6 8 10 12 14 16 18 20 Input Voltage – V Figure 8. Submit Documentation Feedback 7 TL1963A-xx SLVS719E – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com TYPICAL CHARACTERISTICS (continued) GROUND CURRENT vs INPUT VOLTAGE GROUND CURRENT vs INPUT VOLTAGE 10 100 TJ = 25°C 90 VSHDN = VIN TL1963A (Adjustable) VOUT Adjustable 80 TL1963A (Adjustable) VOUT Adjustable 8 VOUT = 1.21 V 70 VOUT = 1.21 V 60 Ground Current – mA Ground Current – mA TJ = 25°C VSHDN = VIN IOUT = 1.5 A 50 40 IOUT = 1 A 30 6 IOUT = 300 mA 4 IOUT = 100 mA 20 2 IOUT = 0.5 A 10 IOUT = 10 mA 0 0 0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 Input Voltage – V Input Voltage – V Figure 9. Figure 10. GROUND CURRENT vs INPUT VOLTAGE GROUND CURRENT vs INPUT VOLTAGE 40 8 9 10 120 TJ = 25°C TJ = 25°C VSHDN = VIN 35 VSHDN = VIN 100 VOUT Fixed 3.3 V TL1963A-3.3 TL1963A-3.3 VOUT Fixed 3.3 V Ground Current – mA Ground Current – mA 30 25 IOUT = 300 mA 20 IOUT = 100 mA 15 IOUT = 10 mA 80 IOUT = 1.5 A 60 40 IOUT = 1 A 10 20 IOUT = 0.5 A 5 0 0 0 1 2 3 4 5 6 Input Voltage – V Figure 11. 8 Submit Documentation Feedback 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10 Input Voltage – V Figure 12. Copyright © 2008–2009, Texas Instruments Incorporated TL1963A-xx www.ti.com........................................................................................................................................................ SLVS719E – JUNE 2008 – REVISED AUGUST 2009 TYPICAL CHARACTERISTICS (continued) GROUND CURRENT vs OUTPUT CURRENT SHDN INPUT CURRENT vs TEMPERATURE 1 80 VIN = VOUT(nom) + 1 VSHDN = 0 V 70 SHDN Input Current – µA Ground Current – mA 60 50 40 30 20 0.75 0.5 0.25 10 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 0 -50 1.6 -25 0 25 50 75 100 125 100 125 TA – Free-Air Temperature – °C Output Current – A Figure 13. Figure 14. SHDN INPUT CURRENT vs SHDN INPUT VOLTAGE SHDN THRESHOLD (OFF TO ON) vs TEMPERATURE 2.5 1 2.25 0.9 2 0.8 SHDN Input Voltage – V SHDN Input Current – µA IOUT = 1 mA 1.75 1.5 1.25 1 0.75 0.7 0.6 0.5 0.4 0.3 0.5 0.2 0.25 0.1 0 0 2 4 6 8 10 12 14 SHDN Input Voltage – V Figure 15. Copyright © 2008–2009, Texas Instruments Incorporated 16 18 20 0 -50 -25 0 25 50 75 TA – Free-Air Temperature – °C Figure 16. Submit Documentation Feedback 9 TL1963A-xx SLVS719E – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com TYPICAL CHARACTERISTICS (continued) SHDN THRESHOLD (ON TO OFF) vs TEMPERATURE ADJ BIAS CURRENT vs TEMPERATURE 5 1 0.9 4.5 0.8 4 0.7 3.5 ADJ Bias Current – µA SHDN Input Voltage – V IOUT = 1 mA 0.6 0.5 0.4 0.3 3 2.5 2 1.5 0.2 1 0.1 0.5 0 -50 -25 0 25 50 75 100 0 -50 125 -25 0 25 50 75 100 125 100 125 TA – Free-Air Temperature – °C TA – Free-Air Temperature – °C Figure 17. Figure 18. CURRENT LIMIT vs INPUT/OUTPUT DIFFERENTIAL VOLTAGE CURRENT LIMIT vs TEMPERATURE 3.5 5 D ?VOUT = 100 mV VIN = 7 V VOUT = 0 V 3 TA = -40°C 4 TA = 25°C Current Limit – A Current Limit – A 2.5 2 TA = 125°C 1.5 3 2 1 1 0.5 0 0 2 4 6 8 10 12 14 16 Input/Output Differential Voltage – V Figure 19. 10 Submit Documentation Feedback 18 20 0 -50 -25 0 25 50 75 TA – Free-Air Temperature – °C Figure 20. Copyright © 2008–2009, Texas Instruments Incorporated TL1963A-xx www.ti.com........................................................................................................................................................ SLVS719E – JUNE 2008 – REVISED AUGUST 2009 TYPICAL CHARACTERISTICS (continued) REVERSE OUTPUT CURRENT vs OUTPUT VOLTAGE REVERSE OUTPUT CURRENT vs TEMPERATURE 12 1000 TJ = 25°C VIN = 0 V VIN = 0 V Current flows into OUT pin Reverse Output Current – µA Reverse Output Current – mA 10 8 VOUT(Adjustable) Adjustable TL1963A VOUT =VVOUT ADJ = VADJ 6 4 2 800 600 VOUT Fixed 3.3V TL1963A-3.3 VOUT= =3.3 3.3VV VOUT 400 V OUT Adjustable TL1963A (Adjustable) VOUT = 1.21 1.21VV OUT = 200 0 VOUT Fixed 3.3 V TL1963A-3.3 VOUT= =VVFB VOUT FB -2 0 2 4 6 8 0 -50 10 -25 Output Voltage – V 0 25 50 75 100 125 100 125 TA – Free-Air Temperature – °C Figure 21. Figure 22. RIPPLE REJECTION vs FREQUENCY LOAD REGULATION vs TEMPERATURE 80 20 IOUT = 1.5 A 15 70 10 Load Regulation – mV Ripple Rejection – dB 60 50 40 30 20 10 VIN = 2.7 V VIN = 2.7 V CIN = 0 CIN = 0 COUT = 10 µF (ceramic) COUT = 10 µF IOUT = 750 mA IOUT = 750 mA VRipple = 0.05 VPP VRipple = 0.05 Vpp TA = 25°C 100 1000 1k 0 -5 -10 -15 TL1963A-1.8 VOUT Fixed 1.8 V TL1963A-2.5 VOUT Fixed 2.5 V -20 -25 TL1963A-3.3 VOUT Fixed 3.3 V -30 -35 0 10 TL1963A VOUT(Adjustable) Adjustable 5 10000 10k Frequency – Hz Figure 23. Copyright © 2008–2009, Texas Instruments Incorporated 100000 100k 100000 1M -50 -25 0 25 50 75 TA – Free-Air Temperature – °C Figure 24. Submit Documentation Feedback 11 TL1963A-xx SLVS719E – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com TYPICAL CHARACTERISTICS (continued) OUTPUT NOISE VOLTAGE vs FREQUENCY LOAD TRANSIENT RESPONSE 1 V = 4.3 V VIN IN = 4.3 V CIN C µF IN = 10 µF COUT == 10 C 10 µF µF (ceramic) Change in Outupt Voltage OUT TL1963A-3.3 V OUT Fixed 3.3 V 0.1 Load Current Output Noise Hz Output NoiseVoltage Voltage––µV/ µVÖRMS 10(ceramic) µF COUTC=OUT 10=µF IOUT =IOUT 1.5=A1.5 A TL1963A (Adjustable) VOUT Adjustable 0.01 10 100 1k Frequency - Hz 10k 20 mV VOUT 0 mV -20 mV 500 mA IOUT 10 mA 100k 500 µs per division Figure 25. Figure 26. LOAD TRANSIENT RESPONSE VININ == 4.3 4.3VV V CININ ==10 10 µF µF C = OUT C =10 10µF µF(ceramic) Change in Outupt Voltage OUT VOUT 20 mV 0 mV Load Current -20 mV 1.5 A IOUT 10 mA 500 µs per division Figure 27. 12 Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated TL1963A-xx www.ti.com........................................................................................................................................................ SLVS719E – JUNE 2008 – REVISED AUGUST 2009 APPLICATION INFORMATION The TL1963A-xx series are 1.5-A LDO regulators optimized for fast transient response. The devices are capable of supplying 1.5 A at a dropout voltage of 340 mV. The low operating quiescent current (1 mA) drops to less than 1 μA in shutdown. In addition to the low quiescent current, the TL1963A-xx regulators incorporate several protection features which make them ideal for use in battery-powered systems. The devices are protected against both reverse input and reverse output voltages. In battery-backup applications where the output can be held up by a backup battery when the input is pulled to ground, the TL1963A-xx acts as if it has a diode in series with its output and prevents reverse current flow. Additionally, in dual-supply applications where the regulator load is returned to a negative supply, the output can be pulled below ground by as much as 20 V and still allow the device to start and operate. Typical Applications IN 10 µF (ceramic) VIN > 3 V 2.5 V at 1.5 A OUT 10 µF (ceramic) TL1963A-2.5 SENSE SHDN GND Figure 29. 3.3 V to 2.5 V Regulator R5 0.01 W TL1963A-1.8 OUT IN VIN > 2.7 V C1 10 µF R1 1 kW + LOAD SHDN SENSE GND R2 80.6 kW R4 2.2 kW R6 2.2 kW C3 1 µF R3 2 kW + C2 3.3 µF R8 100 kW R7 470 kW - NOTE: All capacitors are ceramic. Figure 30. Adjustable Current Source Copyright © 2008–2009, Texas Instruments Incorporated Submit Documentation Feedback 13 TL1963A-xx SLVS719E – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com R1 0.01 W IN VIN > 3.7 V 3.3 V at 3 A OUT TL1963A-3.3 C1 10 µF C2 22 µF SHDN SENSE GND R2 0.01 W IN OUT R6 6.65 kW TL1963A SHDN SHDN SENSE GND R7 4.12 kW R3 2.2 kW R4 2.2 kW R5 1 kW + – C3 0.01 µF NOTE: All capacitors are ceramic. Figure 31. Paralleling Regulators for Higher Output Current RP IN OUT TL1963A VIN SHDN SENSE Load GND RP Figure 32. Kelvin Sense Connection Adjustable Operation The adjustable version of the TL1963A has an output voltage range of 1.21 V to 20 V. The output voltage is set by the ratio of two external resistors as shown in Figure 33. The device maintains the voltage at the ADJ pin at 1.21 V referenced to ground. The current in R1 is then equal to 1.21 V / R1, and the current in R2 is the current in R1 plus the ADJ pin bias current. The ADJ pin bias current, 3 μA at 25°C, flows through R2 into the ADJ pin. The output voltage can be calculated using the formula shown in Figure 33. The value of R1 should be less than 4.17 kΩ to minimize errors in the output voltage caused by the ADJ pin bias current. Note that in shutdown the output is turned off, and the divider current is zero. 14 Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated TL1963A-xx www.ti.com........................................................................................................................................................ SLVS719E – JUNE 2008 – REVISED AUGUST 2009 IN VOUT OUT TL1963A R2 VIN ADJ GND R1 R2 + (I ADJ)(R2) VOUT = 1.21 V )1 + R1) VADJ = 1.21 V IADJ = 3 µA at 25°C Output range = 1.21 V to 20 V Figure 33. Adjustable Operation The adjustable device is tested and specified with the ADJ pin tied to the OUT pin for an output voltage of 1.21 V. Specifications for output voltages greater than 1.21 V are proportional to the ratio of the desired output voltage to 1.21 V: VOUT/1.21 V. For example, load regulation for an output current change of 1 mA to 1.5 A is –3 mV (typ) at VOUT = 1.21 V. At VOUT = 5 V, load regulation is: (5 V/1.21 V)(–3 mV) = –12.4 mV Output Capacitance and Transient Response The TL1963A-xx regulators are designed to be stable with a wide range of output capacitors. The ESR of the output capacitor affects stability, most notably with small capacitors. A minimum output capacitor of 10 μF with an ESR of 3 Ω or less is recommended to prevent oscillations. Larger values of output capacitance can decrease the peak deviations and provide improved transient response for larger load current changes. Bypass capacitors, used to decouple individual components powered by the TL1963A-xx, increase the effective output capacitor value. Extra consideration must be given to the use of ceramic capacitors. Ceramic capacitors are manufactured with a variety of dielectrics, each with different behavior over temperature and applied voltage. The most common dielectrics used are Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics are good for providing high capacitances in a small package, but exhibit strong voltage and temperature coefficients. When used with a 5-V regulator, a 10-μF Y5V capacitor can exhibit an effective value as low as 1 μF to 2 μF over the operating temperature range. The X5R and X7R dielectrics result in more stable characteristics and are more suitable for use as the output capacitor. The X7R type has better stability across temperature, while the X5R is less expensive and is available in higher values. Voltage and temperature coefficients are not the only sources of problems. Some ceramic capacitors have a piezoelectric response. A piezoelectric device generates voltage across its terminals due to mechanical stress, similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor the stress can be induced by vibrations in the system or thermal transients. Overload Recovery Like many IC power regulators, the TL1963A-xx has safe operating area protection. The safe area protection decreases the current limit as input-to-output voltage increases and keeps the power transistor inside a safe operating region for all values of input-to-output voltage. The protection is designed to provide some output current at all values of input-to-output voltage up to the device breakdown. When power is first turned on, as the input voltage rises, the output follows the input, allowing the regulator to start up into very heavy loads. During start up, as the input voltage is rising, the input-to-output voltage differential is small, allowing the regulator to supply large output currents. With a high input voltage, a problem can occur wherein removal of an output short does not allow the output voltage to recover. Other regulators also exhibit this phenomenon, so it is not unique to the TL1963A-xx. Copyright © 2008–2009, Texas Instruments Incorporated Submit Documentation Feedback 15 TL1963A-xx SLVS719E – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com The problem occurs with a heavy output load when the input voltage is high and the output voltage is low. Common situations are immediately after the removal of a short circuit or when the shutdown pin is pulled high after the input voltage has already been turned on. The load line for such a load may intersect the output current curve at two points. If this happens, there are two stable output operating points for the regulator. With this double intersection, the input power supply may need to be cycled down to zero and brought up again to make the output recover. Output Voltage Noise The TL1963A-xx regulators have been designed to provide low output voltage noise over the 10-Hz to 100-kHz bandwidth while operating at full load. Output voltage noise is typically 40 nV/√Hz over this frequency bandwidth for the TL1963A (adjustable version). For higher output voltages (generated by using a resistor divider), the output voltage noise is gained up accordingly. This results in RMS noise over the 10-Hz to 100-kHz bandwidth of 14 μVRMS for the TL1963A, increasing to 38 μVRMS for the TL1963A-3.3. Higher values of output voltage noise may be measured when care is not exercised with regards to circuit layout and testing. Crosstalk from nearby traces can induce unwanted noise onto the output of the TL1963A-xx. Power-supply ripple rejection must also be considered; the TL1963A-xx regulators do not have unlimited power-supply rejection and pass a small portion of the input noise through to the output. Thermal Considerations The power handling capability of the device is limited by the maximum rated junction temperature (125°C). The power dissipated by the device is made up of two components: 1. Output current multiplied by the input/output voltage differential: IOUT(VIN – VOUT) 2. GND pin current multiplied by the input voltage: IGNDVIN. The GND pin current can be found using the GND Pin Current graphs in Typical Characteristics. Power dissipation is equal to the sum of the two components listed above. The TL1963A-xx series regulators have internal thermal limiting designed to protect the device during overload conditions. For continuous normal conditions, the maximum junction temperature rating of 125°C must not be exceeded. It is important to give careful consideration to all sources of thermal resistance from junction to ambient. Additional heat sources mounted nearby must also be considered. For surface-mount devices, heat sinking is accomplished by using the heat-spreading capabilities of the PC board and its copper traces. Copper board stiffeners and plated through-holes also can be used to spread the heat generated by power devices. Table 2 lists thermal resistance for several different board sizes and copper areas. All measurements were taken in still air on 1/16-inch FR-4 board with one-ounce copper. Table 2. KTT Package (5-Pin TO-263) COPPER AREA (1) TOPSIDE (1) 16 BACKSIDE BOARD AREA THERMAL RESISTANCE (JUNCTION TO AMBIENT) 2500 mm2 2500 mm2 2500 mm2 23°C/W 2 1000 mm 2 2500 mm 2500 mm2 25°C/W 125 mm2 2500 mm2 2500 mm2 33°C/W Device is mounted on topside. Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated TL1963A-xx www.ti.com........................................................................................................................................................ SLVS719E – JUNE 2008 – REVISED AUGUST 2009 Calculating Junction Temperature Example: Given an output voltage of 3.3 V, an input voltage range of 4 V to 6 V, an output current range of 0 mA to 500 mA, and a maximum ambient temperature of 50°C, what is the maximum junction temperature? The power dissipated by the device is equal to: IOUT(MAX)(VIN(MAX) – VOUT) + IGND(VIN(MAX)) where, IOUT(MAX) = 500 mA VIN(MAX) = 6 V IGND at (IOUT = 500 mA, VIN = 6 V) = 10 mA So, P = 500 mA (6 V – 3.3 V) + 10 mA (6 V) = 1.41 W Using a KTT package, the thermal resistance is in the range of 23°C/W to 33°C/W, depending on the copper area. So the junction temperature rise above ambient is approximately equal to: 1.41 W × 28°C/W = 39.5°C The maximum junction temperature is then be equal to the maximum junction-temperature rise above ambient plus the maximum ambient temperature or: TJMAX = 50°C + 39.5°C = 89.5°C Protection Features The TL1963A-xx regulators incorporate several protection features that make them ideal for use in battery-powered circuits. In addition to the normal protection features associated with monolithic regulators, such as current limiting and thermal limiting, the devices are protected against reverse input voltages, reverse output voltages and reverse voltages from output to input. Current limit protection and thermal overload protection are intended to protect the device against current overload conditions at the output of the device. For normal operation, the junction temperature should not exceed 125°C. The input of the device withstands reverse voltages of 20 V. Current flow into the device is limited to less than 1 mA (typically less than 100 μA), and no negative voltage appears at the output. The device protects both itself and the load. This provides protection against batteries that can be plugged in backward. The output of the TL1963A-xx can be pulled below ground without damaging the device. If the input is left open circuit or grounded, the output can be pulled below ground by 20 V. For fixed voltage versions, the output acts like a large resistor, typically 5 kΩ or higher, limiting current flow to typically less than 600 μA. For adjustable versions, the output acts like an open circuit; no current flows out of the pin. If the input is powered by a voltage source, the output sources the short-circuit current of the device and protects itself by thermal limiting. In this case, grounding the SHDN pin turns off the device and stops the output from sourcing the short-circuit current. The ADJ pin of the adjustable device can be pulled above or below ground by as much as 7 V without damaging the device. If the input is left open circuit or grounded, the ADJ pin acts like an open circuit when pulled below ground and like a large resistor (typically 5 kΩ) in series with a diode when pulled above ground. In situations where the ADJ pin is connected to a resistor divider that would pull the ADJ pin above its 7-V clamp voltage if the output is pulled high, the ADJ pin input current must be limited to less than 5 mA. For example, a resistor divider is used to provide a regulated 1.5-V output from the 1.21-V reference when the output is forced to 20 V. The top resistor of the resistor divider must be chosen to limit the current into the ADJ pin to less than 5 mA when the ADJ pin is at 7 V. The 13-V difference between OUT and ADJ pins divided by the 5-mA maximum current into the ADJ pin yields a minimum top resistor value of 2.6 kΩ. In circuits where a backup battery is required, several different input/output conditions can occur. The output voltage may be held up while the input is either pulled to ground, pulled to some intermediate voltage, or is left open circuit. Copyright © 2008–2009, Texas Instruments Incorporated Submit Documentation Feedback 17 TL1963A-xx SLVS719E – JUNE 2008 – REVISED AUGUST 2009........................................................................................................................................................ www.ti.com When the IN pin of the TL1963A-xx is forced below the OUT pin or the OUT pin is pulled above the IN pin, input current typically drops to less than 2 μA. This can happen if the input of the device is connected to a discharged (low voltage) battery and the output is held up by either a backup battery or a second regulator circuit. The state of the SHDN pin has no effect on the reverse output current when the output is pulled above the input. 18 Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated PACKAGE OPTION ADDENDUM www.ti.com 7-Dec-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TL1963A-15DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TL1963A-15DCQT ACTIVE SOT-223 DCQ 6 250 CU NIPDAU Level-2-260C-1 YEAR TL1963A-15DCYR ACTIVE SOT-223 DCY 4 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TL1963A-15KTTR ACTIVE DDPAK/ TO-263 KTT 5 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR TL1963A-15KTTRG3 ACTIVE DDPAK/ TO-263 KTT 5 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR TL1963A-15KTTT PREVIEW DDPAK/ TO-263 KTT 5 TBD Call TI Call TI TL1963A-18DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TL1963A-18DCQT ACTIVE SOT-223 DCQ 6 250 CU NIPDAU Level-2-260C-1 YEAR TL1963A-18DCYR ACTIVE SOT-223 DCY 4 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TL1963A-18KTTR ACTIVE DDPAK/ TO-263 KTT 5 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR TL1963A-18KTTRG3 ACTIVE DDPAK/ TO-263 KTT 5 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR TL1963A-18KTTT PREVIEW DDPAK/ TO-263 KTT 5 TBD Call TI Call TI TL1963A-25DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TL1963A-25DCQT ACTIVE SOT-223 DCQ 6 250 CU NIPDAU Level-2-260C-1 YEAR TL1963A-25DCYR ACTIVE SOT-223 DCY 4 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TL1963A-25KTTR ACTIVE DDPAK/ TO-263 KTT 5 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR TL1963A-25KTTRG3 ACTIVE DDPAK/ TO-263 KTT 5 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR TL1963A-25KTTT PREVIEW DDPAK/ TO-263 KTT 5 TBD Call TI Call TI TL1963A-33DCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TL1963A-33DCQT ACTIVE SOT-223 DCQ 6 250 CU NIPDAU Level-2-260C-1 YEAR TL1963A-33DCYR ACTIVE SOT-223 DCY 4 2500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR TL1963A-33KTTR ACTIVE DDPAK/ TO-263 KTT 5 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR TL1963A-33KTTT PREVIEW DDPAK/ TO-263 KTT 5 TBD Call TI Call TI TL1963ADCQR ACTIVE SOT-223 DCQ 6 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TL1963ADCQT ACTIVE SOT-223 DCQ 6 250 CU NIPDAU Level-2-260C-1 YEAR Addendum-Page 1 Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Green (RoHS & no Sb/Br) Lead/Ball Finish MSL Peak Temp (3) PACKAGE OPTION ADDENDUM www.ti.com 7-Dec-2009 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TL1963AKTTR ACTIVE DDPAK/ TO-263 KTT 5 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR TL1963AKTTRG3 ACTIVE DDPAK/ TO-263 KTT 5 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 20-Jul-2010 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) TL1963A-15DCQR SOT-223 DCQ 6 2500 330.0 12.4 TL1963A-15DCQT SOT-223 DCQ 6 250 177.8 TL1963A-15DCYR SOT-223 DCY 4 2500 330.0 TL1963A-15KTTR DDPAK/ TO-263 KTT 5 500 TL1963A-18DCQR SOT-223 DCQ 6 TL1963A-18DCQT SOT-223 DCQ 6 TL1963A-18DCYR SOT-223 DCY TL1963A-18KTTR DDPAK/ TO-263 TL1963A-25DCQR 6.8 7.3 1.88 8.0 12.0 Q3 12.4 7.05 7.45 1.88 8.0 12.0 Q3 12.4 7.05 7.4 1.9 8.0 12.0 Q3 330.0 24.4 10.6 15.8 4.9 16.0 24.0 Q2 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 250 177.8 12.4 7.05 7.45 1.88 8.0 12.0 Q3 4 2500 330.0 12.4 7.05 7.4 1.9 8.0 12.0 Q3 KTT 5 500 330.0 24.4 10.6 15.8 4.9 16.0 24.0 Q2 SOT-223 DCQ 6 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 TL1963A-25DCQT SOT-223 DCQ 6 250 177.8 12.4 7.05 7.45 1.88 8.0 12.0 Q3 TL1963A-25DCYR SOT-223 DCY 4 2500 330.0 12.4 7.05 7.4 1.9 8.0 12.0 Q3 TL1963A-25KTTR DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.6 15.8 4.9 16.0 24.0 Q2 TL1963A-33DCQR SOT-223 DCQ 6 2500 330.0 12.4 6.8 7.3 1.88 8.0 12.0 Q3 TL1963A-33DCQT SOT-223 DCQ 6 250 177.8 12.4 7.05 7.45 1.88 8.0 12.0 Q3 TL1963A-33DCYR SOT-223 DCY 4 2500 330.0 12.4 7.05 7.4 1.9 8.0 12.0 Q3 TL1963A-33KTTR DDPAK/ KTT 5 500 330.0 24.4 10.6 15.8 4.9 16.0 24.0 Q2 Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 20-Jul-2010 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 8.0 12.0 Q3 TO-263 TL1963ADCQR SOT-223 DCQ 6 2500 330.0 12.4 6.8 7.3 1.88 TL1963ADCQT SOT-223 DCQ 6 250 177.8 12.4 7.05 7.45 1.88 8.0 12.0 Q3 TL1963AKTTR DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.6 15.8 4.9 16.0 24.0 Q2 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TL1963A-15DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TL1963A-15DCQT SOT-223 DCQ 6 250 180.0 180.0 85.0 TL1963A-15DCYR SOT-223 DCY 4 2500 340.0 340.0 38.0 TL1963A-15KTTR DDPAK/TO-263 KTT 5 500 340.0 340.0 38.0 TL1963A-18DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TL1963A-18DCQT SOT-223 DCQ 6 250 180.0 180.0 85.0 TL1963A-18DCYR SOT-223 DCY 4 2500 340.0 340.0 38.0 TL1963A-18KTTR DDPAK/TO-263 KTT 5 500 340.0 340.0 38.0 TL1963A-25DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TL1963A-25DCQT SOT-223 DCQ 6 250 180.0 180.0 85.0 TL1963A-25DCYR SOT-223 DCY 4 2500 340.0 340.0 38.0 TL1963A-25KTTR DDPAK/TO-263 KTT 5 500 340.0 340.0 38.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 20-Jul-2010 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TL1963A-33DCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TL1963A-33DCQT SOT-223 DCQ 6 250 180.0 180.0 85.0 TL1963A-33DCYR SOT-223 DCY 4 2500 340.0 340.0 38.0 TL1963A-33KTTR DDPAK/TO-263 KTT 5 500 340.0 340.0 38.0 TL1963ADCQR SOT-223 DCQ 6 2500 358.0 335.0 35.0 TL1963ADCQT SOT-223 DCQ 6 250 180.0 180.0 85.0 TL1963AKTTR DDPAK/TO-263 KTT 5 500 340.0 340.0 38.0 Pack Materials-Page 3 MECHANICAL DATA MPDS094A – APRIL 2001 – REVISED JUNE 2002 DCY (R-PDSO-G4) PLASTIC SMALL-OUTLINE 6,70 (0.264) 6,30 (0.248) 3,10 (0.122) 2,90 (0.114) 4 0,10 (0.004) M 3,70 (0.146) 3,30 (0.130) 7,30 (0.287) 6,70 (0.264) Gauge Plane 1 2 0,84 (0.033) 0,66 (0.026) 2,30 (0.091) 4,60 (0.181) 1,80 (0.071) MAX 3 0°–10° 0,10 (0.004) M 0,25 (0.010) 0,75 (0.030) MIN 1,70 (0.067) 1,50 (0.059) 0,35 (0.014) 0,23 (0.009) Seating Plane 0,08 (0.003) 0,10 (0.0040) 0,02 (0.0008) 4202506/B 06/2002 NOTES: A. B. C. D. All linear dimensions are in millimeters (inches). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC TO-261 Variation AA. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated