ACTIVE (DIGITAL) DELAY LINES RESISTORS "CAPS & COILS "DELAY LINES A0805 SERIES 5-TAP 8-PIN DIP SA0805 SERIES 5-TAP 8-PIN SIP A1405 SERIES 5-TAP 8-PIN DIP A1410 SERIES 10-TAP 14-PIN DIP Wide selection of sizes! RCD’s digital delay lines have been designed to provide precise tap delays with all the necessary drive and pick-off circuitry. All inputs and outputs are schottky-type and require no additional components to achieve specified delays. Encapsulated/molded construction ensures full compliance to all applicable requirements of MIL-D-23859. Units are 100% inspected for solder joint integrity and electrical conformance. FEATURES ! Economical cost, prompt delivery! ! Wide varieties of values ! Choice of 5 or 10 equally spaced taps ! TTL and DTL compatible ! Operating temperature: 0°C to 70°C ! Excellent for applications requiring high delay stability, fast rise times and no jitter, such as memory boards, disk drives, and signal processing OPTIONS ! Non-standard delay times or tolerances ! Non-symmetrical tap delays ! Dynamic RAM timing delay ! Fast logic TTL available ! Faster rise times ! ECL, H-CMOS, and low power designs available ! Option T - Measurement at both leading and trailing edges ! Option ER - Ceramic IC’s screened to MILSTD-883, -55 to +125°C per MIL-D-83532 ! Option 39 - -40-+85°C op. temp. Delay Per Tap (nSec) Total Delay A0805 SA080 A1410 A1405 20 25 30 40 50 60 75 100 125 150 175 200 250 300 350 400 450 500 750 1000 4 5 6 8 10 12 15 20 25 30 35 40 50 60 70 80 90 100 150 200 * * * * 5 6 7.5 10 12.5 15 17.5 20 25 30 35 40 45 50 75 100 TEST CONDITIONS @25°C 1) Delay measured at 1.5V on leading edge only with no loads on output. 2) Rise time measured from 0.75V to 2.4V. 3) Delay will inversely vary approximately 4% for every 5% change in supply voltage. 4) Supply voltage (VCC) = 5.0±.25VDC 5) Input test pulse: 3.2V, 2nS rise time, width>40% of total delay, pulse period to be a minimum of 3x the pulse width. TYPE A0805 (Available 20nS to 500nS) .018 [.457] → Typ. ← [2.54] ← ↓ → R 4 .300 [7.62] Typ. ←.810 [20.6] Max.→ .340 [8.64] Max. .150 [3.81] Typ. .020 [.51] G Outputs 3 4 5 6 .180 → [4.57] Max. 7 1 ← VCC 2 IN .018→ [.457] Typ. ← → ← .100 [2.54] G [.254] Typ. R 8 → ← .010 TYPE A1405 - Economy TYPE A1405A TYPE A1410 (20nS to 1000nS) Auto Insertable Molded (20nS to 1000nS)-also avail. in .165” profile (Available 50nS to 1000nS) ↓ ←.785 [19.9] Max.→ .280 [7.11] Max. .018 → ← → [.457] Typ. ← → .300 ←[7.62] → ←.600±.010 [12.7±.254]→ .050 [1.27] Typ. ↓ ↑ ← ↑ .010 [.254] .300±.010 [7.62±.254] ←.800 [20.3] Max.→ .050 [1.27] ↓ → → ← 12 4 10 6 14 VCC 1 IN G 7 R ← .100 [2.54] ↑ .400 [10.2] Max. ↓ 8 OUT → ←.800 [20.3] Max.→ ↓ .300±.010 [7.62±.254] P/N DESIGNATION: Total Delay Tolerance ±5% or 2nS (whichever is greater) Tap Delay Tolerance ±5% or 2nS (whichever is greater) Insulation Resistance 1000MΩ min. Dielectric Strength 100V D C Rise Time 4nS max. ↑ ↓ .020±.003 [.5±.076] * Consult factory for availability. ELECTRICAL CHARACTERISTICS .150 [3.81] Typ. ↑ ↓ ↑ .300±.01 ←[7.62±.254] → ↓ ←.600±.010 → [12.7±.254] .280 [7.11] ←.800 [20.3] Max.→ .300 [7.62] Max. ↑ ↑ ↓ ↓ .25 [6.35] ↑ .100 [2.54] Typ. .100 [2.54] ↓ .100 ← → 5 8 ↑ VCC ↑ .400 .300 1 [7.62] [10.2] Max. IN ↓ TYPE SA0805 (Available 20nS to 250nS) ↓ .400 [10.2] → .250 ↑ [6.35] Max. ↓ .120 [3.05] Min. ↑ ← Outputs 7 2 6 3 .500 [12.7] Max. 13 3 12 4 11 5 10 6 9 14 VCC IN 1 G R 7 A1405 - 100nS - B RCD Type Options: (leave blank if standard) ER, T, 39, or as assigned by RCD Total Delay Packaging: B=bulk (standard) RCD Components Inc., 520 E. Industrial Park Dr., Manchester, NH, USA 03109 Tel: (603) 669-0054 Fax:(603) 669-5455 E-mail: [email protected] www.rcdcomponents.com FA specifications subject to change without notice 8 OUT