05190 EMIF6-100FC Only One Name Means ProTek’Tion™ EMI FILTER/TVS ARRAY APPLICATIONS ✔ Cellular Phones ✔ Notebooks ✔ Personal Digital Assistant (PDA) ✔ Ground Positioning System (GPS) ✔ SMART Cards IEC COMPATIBILITY (EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns FEATURES ✔ ESD Protection > 25 kilovolts ✔ Bidirectional EMI Filtering/TVS Low Pass Filters ✔ Low Insertion Loss: -3db Roll-Off @ 60MHz ✔ Protects Up to Six(6) Data Lines MECHANICAL CHARACTERISTICS ✔ Flip Chip Package ✔ Weight 0.73 milligrams (Approximate) ✔ Flammability rating UL 94V-0 ✔ 8mm Tape and Reel Per EIA Standard 481 PIN CONFIGURATION G1 05190.R1 9/03 G2 1 G3 www.protekdevices.com EMIF6-100FC DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25°C Unless Otherwise Specified SYMBOL VALUE UNITS TJ -40°C to 85°C °C TSTG -55°C to 150°C °C DC Power Per Resistor P 100 mW Typical Resistance @ ± 20% R 100 OHMS PARAMETER Operating Temperature Storage Temperature ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified PART NUMBER RATED STAND-OFF VOLTAGE MINIMUM BREAKDOWN VOLTAGE MAXIMUM REVERSE LEAKAGE CURRENT TYPICAL FORWARD VOLTAGE MINIMUM ATTENUATION VWM VOLTS @ 1mA V(BR) VOLTS @ 3V ID µA @10mA VF VOLTS @ 800-3000 MHz dB fc MHz @2.5V, 1 MHz C pF 5.0 6.0 0.1 0.8 30 60 54 EMIF6-100FC CUT-OFF TYPICAL FREQUENCY CAPACITANCE (50 Ohms I/O PER LINE ZERO BIAS) (See Note 1) Note 1: ±20% tolerance. FIGURE 1 RESISTANCE VS TEMPERATURE (Normalized to Resistance at 25°C) Normalized Resistance 1.100 1.060 1.020 0.980 0.940 0.900 -40 05190.R1 9/03 -20 0 20 40 Temperature °C 2 60 80 100 www.protekdevices.com EMIF6-100FC GRAPHS FIGURE 2 INSERTION LOSS - EMIF6-100FC 0 -5 -10 Gain (dB) -15 -20 2.5 Volts -25 -30 -35 0 Volts -40 -45 -50 0.1 1 10 100 1000 10000 Frequency (MHz) FIGURE 3 OVERSHOOT & CLAMPING VOLTAGE FOR EMIF6-100FC 5 Volts per Division 35 25 15 5 -5 ESD Test Pulse: +15 kilovolt, 1/30ns (waveform) FIGURE 4 OVERSHOOT & CLAMPING VOLTAGE FOR EMIF6-100FC 1 Volts per Division 4 2 0 -2 -4 ESD Test Pulse: -15 kilovolt, 1/30ns (waveform) 05190.R1 9/03 3 www.protekdevices.com EMIF6-100FC APPLICATION INFORMATION PRINTED CIRCUIT BOARD RECOMMENDATIONS VALUE PARAMETER Pad Size on PCB 0.275mm Round Pad Shape Pad Definition Non-Solder Mask Defined Pads 0.325mm Round Solder Mask Opening Solder Stencil Thickness Solder Stencil Aperture Opening (laser cut, 5% tapered walls) Solder Flux Ratio Solder Paste Type Pad Protective Finish 0.150mm 0.330mm Round 50/50 By Volume No Clean OSP(Entek Cu Plus 106A) ±50µm Tolerance - Edge To Corner Ball Solder Ball Side Coplanarity ±20µm 60 Seconds Maximum Dwell Time Above Liquidous (183°C) Soldering Maximum Temperature 240°C FIGURE 5 RECOMMENDED NON-SOLDER MASK DEFINED PAD ILLUSTRATION Non-Solder Mask Defined Pad 0.275mm DIA. Solder Mask Opening 0.325mm DIA. Solder Stencil Opening 0.330mm DIA. FIGURE 6 SOLDER REFLOW PROFILE Note: This reflow profile does not take into account the printed circuit board (PCB) material heating time. Additional time may be required for the preheat time and cool down time upon the PCB or board material. 225°C 5-10 sec 200°C Instantaneous to 200°C 1-2 Minutes to 150°C 1-2 Minutes to 25°C 100°C Pre-Heat Time 05190.R1 9/03 4 Soldering Time Cool Down Time www.protekdevices.com EMIF6-100FC PACKAGE OUTLINE & DIMENSIONS PACKAGE OUTLINE PACKAGE DIMENSIONS MILLIMETERS BOTTOM VIEW A G D C SIDE VIEW E O F G B H I 1 2 3 4 5 6 I INCHES DIM MIN MAX MIN MAX A B C D E F G H I J 2.915 1.285 0.495 0.245 0.430 0.430 0.180 0.180 0.432 0.330 3.005 1.375 0.505 0.255 0.440 0.440 0.280 0.280 0.559 0.457 0.1148 0.0506 0.0195 0.0096 0.0169 0.0169 0.0071 0.0071 0.017 0.013 0.1183 0.0541 0.0199 0.0100 0.0173 0.0173 0.0110 0.0110 0.022 0.018 J 0.30 DIA. 63/37 Sn/Pb Solder Bumps NOTE: 1. Controlling dimensions in millimeters. TAPE & REEL SPECIFICATIONS PART NUMBER CHIP SIZE (mm) POCKET SIZE (mm) B0 x A0 x K0 TAPE WIDTH W REEL DIAMETER QTY PER REEL P0 P1 EMIF6-100FC 2.96 x 1.33 x 0.6 ± 0.05 3.18 x 1.52 x 0.76 ±0.1 8mm 7” 3,000 4mm 4mm Top Cover Tape P0 10 Pitches Cumulative Tolerance On Tape ±0.2mm A0 W B0 K0 For Tape Feeder Reference Only Including Draft Concentric Around B P1 Embossment Direction of Feed Outline & Dimensions: Rev 0 - 8/03, 06042 TAPE & REEL ORDERING NOMENCLATURE 1. Surface mount product is taped and reeled in accordance with EIA-481. 2. Plastic 8mm Tape: Suffix-T73-1 = 7 Inch Reel - 3,000 pieces per reel, i.e., EMIF6-100FC-T73-1. ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: [email protected] Web Site: www.protekdevices.com COPYRIGHT © ProTek Devices 2003 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. 05190.R1 9/03 5 www.protekdevices.com