TI SM320F2808PZMEP

SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
Data Manual
Literature Number: SGLS316A
March 2006 – Revised February 2007
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Contents
1
2
Features.............................................................................................................................. 9
Introduction ....................................................................................................................... 10
2.1
2.2
3
Functional Overview ........................................................................................................... 20
3.1
3.2
3.3
3.4
3.5
3.6
3.7
4
21
25
25
26
26
26
26
27
27
27
28
28
29
29
29
29
29
29
30
30
30
30
31
33
34
36
37
38
41
42
32-Bit CPU-Timers 0/1/2 ..................................................................................................
Enhanced PWM Modules (ePWM1/2/3/4/5/6) ..........................................................................
Hi-Resolution PWM (HRPWM) ...........................................................................................
Enhanced CAP Modules (eCAP1/2/3/4) ................................................................................
Enhanced QEP Modules (eQEP1/2).....................................................................................
Enhanced Analog-to-Digital Converter (ADC) Module ................................................................
Enhanced Controller Area Network (eCAN) Modules (eCAN-A and eCAN-B).....................................
Serial Communications Interface (SCI) Modules (SCI-A, SCI-B) ....................................................
Serial Peripheral Interface (SPI) Modules (SPI-A, SPI-B, SPI-C, SPI-D) ...........................................
Inter-Integrated Circuit (I2C)...............................................................................................
GPIO MUX ..................................................................................................................
43
45
47
48
49
52
57
62
65
69
71
Device Support .................................................................................................................. 75
5.1
2
Memory Map ................................................................................................................
Brief Descriptions...........................................................................................................
3.2.1
C28x CPU .......................................................................................................
3.2.2
Memory Bus (Harvard Bus Architecture) ....................................................................
3.2.3
Peripheral Bus ..................................................................................................
3.2.4
Real-Time JTAG and Analysis ................................................................................
3.2.5
Flash ..............................................................................................................
3.2.6
M0, M1 SARAMs ...............................................................................................
3.2.7
L0, L1, H0 SARAMs ............................................................................................
3.2.8
Boot ROM ........................................................................................................
3.2.9
Security ..........................................................................................................
3.2.10 Peripheral Interrupt Expansion (PIE) Block ..................................................................
3.2.11 External Interrupts (XINT1, XINT2, XNMI) ...................................................................
3.2.12 Oscillator and PLL ..............................................................................................
3.2.13 Watchdog ........................................................................................................
3.2.14 Peripheral Clocking .............................................................................................
3.2.15 Low-Power Modes ..............................................................................................
3.2.16 Peripheral Frames 0, 1, 2 (PFn) ..............................................................................
3.2.17 General-Purpose Input/Output (GPIO) Multiplexer .........................................................
3.2.18 32-Bit CPU-Timers (0, 1, 2) ...................................................................................
3.2.19 Control Peripherals .............................................................................................
3.2.20 Serial Port Peripherals .........................................................................................
Register Map ................................................................................................................
Device Emulation Registers...............................................................................................
Interrupts ....................................................................................................................
3.5.1
External Interrupts ..............................................................................................
System Control .............................................................................................................
3.6.1
OSC and PLL Block ............................................................................................
3.6.2
Watchdog Block .................................................................................................
Low-Power Modes Block ..................................................................................................
Peripherals ........................................................................................................................ 43
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
5
ORDERING INFORMATION.............................................................................................. 10
Pin Assignments............................................................................................................ 11
Signal Descriptions ......................................................................................................... 14
Device and Development Support Tool Nomenclature................................................................ 75
Contents
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
5.2
6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
7
Documentation Support
...................................................................................................
76
Electrical Specifications ...................................................................................................... 79
Absolute Maximum Ratings ............................................................................................... 79
Recommended Operating Conditions ................................................................................... 79
Electrical Characteristics ................................................................................................. 80
Current Consumption ..................................................................................................... 80
6.4.1
Reducing Current Consumption .............................................................................. 83
6.4.2
Current Consumption Graphs .................................................................................. 84
Timing Parameter Symbology ............................................................................................ 84
6.5.1
General Notes on Timing Parameters ........................................................................ 85
6.5.2
Test Load Circuit ................................................................................................ 85
6.5.3
Device Clock Table ............................................................................................. 85
Clock Requirements and Characteristics ............................................................................... 86
Power Sequencing ......................................................................................................... 87
6.7.1
Power Management and Supervisory Circuit Solutions .................................................... 88
General-Purpose Input/Output (GPIO) .................................................................................. 91
6.8.1
GPIO - Output Timing ........................................................................................... 91
6.8.2
GPIO - Input Timing ............................................................................................. 92
6.8.3
Sampling Window Width for Input Signals ................................................................... 92
6.8.4
Low-Power Mode Wakeup Timing ............................................................................ 94
Enhanced Control Peripherals ............................................................................................ 96
6.9.1
Enhanced Pulse Width Modulator (ePWM) Timing ......................................................... 96
6.9.2
Trip-Zone Input Timing.......................................................................................... 97
6.9.3
External Interrupt Timing ....................................................................................... 99
6.9.4
I2C Electrical Specification and Timing ..................................................................... 100
6.9.5
Serial Peripheral Interface (SPI) Master Mode Timing .................................................... 100
6.9.6
SPI Slave Mode Timing ....................................................................................... 104
6.9.7
On-Chip Analog-to-Digital Converter ........................................................................ 107
Detailed Descriptions .................................................................................................... 112
Flash Timing ............................................................................................................... 113
Mechanical Data ............................................................................................................... 115
Contents
3
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
List of Figures
2-1
SM320F2808 100-Pin PZ LQFP (Top View) .................................................................................. 11
2-2
F2806 100-Pin PZ LQFP (Top View) ........................................................................................... 12
2-3
F2801/UCD9501 100-Pin PZ LQFP (Top View) .............................................................................. 13
2-4
SM320F280x 100-Ball GGM and ZGM MicroStar™ BGA (Bottom View) ................................................. 14
3-1
Functional Block Diagram ........................................................................................................ 20
3-2
F2808 Memory Map
3-3
3-4
3-5
3-6
3-7
3-8
3-9
3-10
3-11
3-12
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
5-1
5-2
6-1
6-2
6-3
6-4
4
..............................................................................................................
F2806 Memory Map ..............................................................................................................
F2801/9501 Memory Map........................................................................................................
External and PIE Interrupt Sources .............................................................................................
Multiplexing of Interrupts Using the PIE Block ................................................................................
Clock and Reset Domains .......................................................................................................
OSC and PLL Block Diagram ...................................................................................................
Using a 3.3-V External Oscillator ...............................................................................................
Using a 1.8-V External Oscillator ...............................................................................................
Using the Internal Oscillator .....................................................................................................
Watchdog Module .................................................................................................................
CPU-Timers ........................................................................................................................
CPU-Timer Interrupt Signals and Output Signal ..............................................................................
Multiple PWM Modules in a 280x System .....................................................................................
ePWM Sub-modules Showing Critical Internal Signal Interconects ........................................................
eCAP Functional Block Diagram ................................................................................................
eQEP Functional Block Diagram ................................................................................................
Block Diagram of the ADC Module .............................................................................................
ADC Pin Connections With Internal Reference ...............................................................................
ADC Pin Connections With External Reference ..............................................................................
eCAN Block Diagram and Interface Circuit ....................................................................................
eCAN-A Memory Map ............................................................................................................
eCAN-B Memory Map ............................................................................................................
Serial Communications Interface (SCI) Module Block Diagram ............................................................
SPI Module Block Diagram (Slave Mode) .....................................................................................
I2C Peripheral Module Interfaces ...............................................................................................
GPIO MUX Block Diagram .......................................................................................................
Qualification Using Sampling Window..........................................................................................
Example of SM320x280x Device Nomenclature ..............................................................................
Example of UCD Device Nomenclature ........................................................................................
Wirebond / EM Life for SM320F280xPZMEP .................................................................................
Typical Operational Current Versus Frequency (F2808) ....................................................................
Typical Operational Power Versus Frequency (F2808) ......................................................................
3.3-V Test Load Circuit ...........................................................................................................
List of Figures
21
22
23
34
35
37
38
39
39
39
41
43
44
45
47
48
50
53
54
55
58
59
60
64
68
70
71
74
76
76
82
84
84
85
Submit Documentation Feedback
www.ti.com
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6-5
Clock Timing ....................................................................................................................... 87
6-6
Power-on Reset ................................................................................................................... 89
6-7
Warm Reset........................................................................................................................ 90
6-8
........................................................................... 91
General-Purpose Output Timing ................................................................................................ 91
Sampling Mode .................................................................................................................... 92
General-Purpose Input Timing .................................................................................................. 93
IDLE Entry and Exit Timing ...................................................................................................... 94
STANDBY Entry and Exit Timing Diagram .................................................................................... 95
HALT Wake Up Using GPIOn ................................................................................................... 96
PWM Hi-Z Characteristics ....................................................................................................... 97
ADCSOCAO or ADCSOCBO Timing ........................................................................................... 99
External Interrupt Timing ......................................................................................................... 99
SPI Master Mode External Timing (Clock Phase = 0) ...................................................................... 102
SPI Master External Timing (Clock Phase = 1).............................................................................. 104
SPI Slave Mode External Timing (Clock Phase = 0)........................................................................ 105
SPI Slave Mode External Timing (Clock Phase = 1)........................................................................ 106
ADC Power-Up Control Bit Timing ............................................................................................ 108
ADC Analog Input Impedance Model ......................................................................................... 109
Sequential Sampling Mode (Single-Channel) Timing ....................................................................... 110
Simultaneous Sampling Mode Timing ........................................................................................ 111
6-9
6-10
6-11
6-12
6-13
6-14
6-15
6-16
6-17
6-18
6-19
6-20
6-21
6-22
6-23
6-24
6-25
Example of Effect of Writing Into PLLCR Register
List of Figures
5
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
List of Tables
2-1
2-2
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
3-9
3-10
3-11
3-12
3-13
3-14
3-15
3-16
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
6-1
6-2
6-3
6-4
6-5
6
...............................................................................................................
Signal Descriptions ...............................................................................................................
Addresses of Flash Sectors in F2808 ..........................................................................................
Addresses of Flash Sectors in F2806 ..........................................................................................
Addresses of Flash Sectors in F2801/9501 ...................................................................................
Wait States .........................................................................................................................
Boot Mode Selection..............................................................................................................
Peripheral Frame 0 Registers ...................................................................................................
Peripheral Frame 1 Registers ...................................................................................................
Peripheral Frame 2 Registers ...................................................................................................
Device Emulation Registers .....................................................................................................
PIE Peripheral Interrupts .........................................................................................................
PIE Configuration and Control Registers ......................................................................................
External Interrupt Registers ......................................................................................................
PLL, Clocking, Watchdog, and Low-Power Mode Registers ................................................................
PLLCR Register Bit Definitions ..................................................................................................
Possible PLL Configuration Modes .............................................................................................
Low-Power Modes ................................................................................................................
CPU-Timers 0, 1, 2 Configuration and Control Registers ...................................................................
ePWM Control and Status Registers ...........................................................................................
eCAP Control and Status Registers ............................................................................................
eQEP Control and Status Registers ............................................................................................
ADC Registers .....................................................................................................................
3.3-V eCAN Transceivers .......................................................................................................
CAN Register Map ................................................................................................................
SCI-A Registers ...................................................................................................................
SCI-B Registers ...................................................................................................................
SPI-A Registers ...................................................................................................................
SPI-B Registers ...................................................................................................................
SPI-C Registers ...................................................................................................................
SPI-D Registers ...................................................................................................................
I2C-A Registers ....................................................................................................................
GPIO Registers ...................................................................................................................
F2808 GPIO MUX Table .........................................................................................................
SM320F2808 Current Consumption by Power-Supply Pins at 100-MHz SYSCLKOUT .................................
F2806 Current Consumption by Power-supply Pins at 100 MHz SYSCLKOUT .........................................
F2801/UCD9501 Current Consumption by Power-supply Pins at 100-MHz SYSCLKOUT .............................
Typical Current Consumption by Various Peripherals (at 100 MHz) .......................................................
TMS320x280x Clock Table and Nomenclature ...............................................................................
Hardware Features
List of Tables
10
15
24
24
24
25
27
31
32
33
33
35
36
36
38
40
40
42
44
46
49
51
56
58
61
63
63
66
66
67
67
70
72
73
80
81
82
83
86
Submit Documentation Feedback
www.ti.com
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6-6
6-7
6-8
6-9
6-10
6-11
6-12
6-13
6-14
6-15
6-16
6-17
6-18
6-19
6-20
6-21
6-22
6-23
6-24
6-25
6-26
6-27
6-28
6-29
6-30
6-31
6-32
6-33
6-34
6-35
6-36
6-37
6-38
6-39
6-40
6-41
6-42
6-43
6-44
7-1
7-2
........................................................................................................... 86
XCLKIN Timing Requirements - PLL Enabled ................................................................................ 86
XCLKIN Timing Requirements - PLL Disabled ................................................................................ 86
XCLKOUT Switching Characteristics (PLL Bypassed or Enabled) ......................................................... 87
Power Management and Supervisory Circuit Solutions ...................................................................... 88
Reset (XRS) Timing Requirements ............................................................................................ 90
General-Purpose Output Switching Characteristics .......................................................................... 91
General-Purpose Input Timing Requirements ................................................................................. 92
IDLE Mode Timing Requirements............................................................................................... 94
IDLE Mode Switching Characteristics .......................................................................................... 94
STANDBY Mode Timing Requirements ........................................................................................ 94
STANDBY Mode Switching Characteristics .................................................................................. 95
HALT Mode Timing Requirements .............................................................................................. 95
HALT Mode Switching Characteristics ........................................................................................ 96
ePWM Timing Requirements .................................................................................................... 97
ePWM Switching Characteristics................................................................................................ 97
Trip-Zone input Timing Requirements .......................................................................................... 97
High Resolution PWM Characteristics at SYSCLKOUT = (60 - 100 MHz) ................................................ 98
Enhanced Capture (eCAP) Timing Requirement ............................................................................. 98
eCAP Switching Characteristics................................................................................................. 98
Enhanced Quadrature Encoder Pulse (eQEP) Timing Requirements ..................................................... 98
eQEP Switching Characteristics ................................................................................................ 98
External ADC Start-of-Conversion Switching Characteristics ............................................................... 98
External Interrupt Timing Requirements ....................................................................................... 99
External Interrupt Switching Characteristics ................................................................................... 99
I2C Timing ....................................................................................................................... 100
SPI Master Mode External Timing (Clock Phase = 0) ...................................................................... 101
SPI Master Mode External Timing (Clock Phase = 1) ...................................................................... 103
SPI Slave Mode External Timing (Clock Phase = 0)........................................................................ 104
SPI Slave Mode External Timing (Clock Phase = 1)........................................................................ 105
ADC Electrical Characteristics (over recommended operating conditions) .............................................. 107
ADC Power-Up Delays.......................................................................................................... 108
Current Consumption for Different ADC Configurations (at 12.5-MHz ADCCLK) ....................................... 108
Sequential Sampling Mode Timing ............................................................................................ 110
Simultaneous Sampling Mode Timing ........................................................................................ 111
Flash Endurance ................................................................................................................. 113
Flash Parameters at 100-MHz SYSCLKOUT ................................................................................ 113
Flash/OTP Access Timing ...................................................................................................... 113
Minimum Required Wait-States at Different Frequencies .................................................................. 114
F280x Thermal Model 100-pin GGM Results ................................................................................ 115
F280x Thermal Model 100-pin PZ Results ................................................................................... 115
Input Clock Frequency
List of Tables
7
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
8
List of Tables
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
1
•
•
•
•
•
•
•
•
•
•
•
(1)
Features
Controlled Baseline
– One Assembly/Test/Fabrication Site
Enhanced Diminishing Manufacturing Sources
(DMS) Support
Enhanced Product-Change Notification
Qualification Pedigree (1)
High-Performance Static CMOS Technology
– 100 MHz (10-ns Cycle Time)
– Low-Power (1.8-V Core, 3.3-V I/O) Design
– 3.3-V Flash Voltage
JTAG Boundary Scan Support
High-Performance 32-Bit CPU (TMS320C28x)
– 16 x 16 and 32 x 32 MAC Operations
– 16 x 16 Dual MAC
– Harvard Bus Architecture
– Atomic Operations
– Fast Interrupt Response and Processing
– Unified Memory Programming Model
– Code-Efficient (in C/C++ and Assembly)
On-Chip Memory
– F2808: 64K X 16 Flash, 18K X 16 SARAM
F2806: 32K X 16 Flash, 10K X 16 SARAM
F2801: 16K X 16 Flash, 6K X 16 SARAM
9501: 16K X 16 Flash, 6K X 16 SARAM
– 1K x 16 OTP ROM
Boot ROM (4K x 16)
– With Software Boot Modes (via SCI, SPI,
CAN, I2C, and Parallel I/O)
– Standard Math Tables
Clock and System Control
– Dynamic PLL Ratio Changes Supported
– On-Chip Oscillator
– Clock-Fail-Detect Mode
– Watchdog Timer Module
Any GPIO A Pin Can Be Connected to One of
the Three External Core Interrupts
Component qualification in accordance with JEDEC and
industry standards to ensure reliable operation over an
extended temperature range. This includes, but is not limited
to, Highly Accelerated Stress Test (HAST) or biased 85/85,
temperature cycle, autoclave or unbiased HAST,
electromigration, bond intermetallic life, and mold compound
life. Such qualification testing should not be viewed as
justifying use of this component beyond specified
performance and environmental limits.
•
•
•
•
•
•
•
•
•
•
•
Peripheral Interrupt Expansion (PIE) Block
That Supports All 43 Peripheral Interrupts
128-Bit Security Key/Lock
– Protects Flash/OTP/L0/L1 Blocks
– Prevents Firmware Reverse Engineering
Enhanced Control Peripherals
– Up to 16 PWM Outputs
– Up to Four HRPWM Outputs With 150 ps
MEP Resolution
– Up to Four Capture Inputs
– Up to Two Quadrature Encoder Interfaces
– Up to Six 32-bit Timers
– Up to Six 16-bit Timers
Three 32-Bit CPU Timers
Serial Port Peripherals
– Up to Four Serial Peripheral Interface (SPI)
Modules
– Up to Two Serial Communications Interface
(SCI), Standard UART Modules
– Up to Two Enhanced Controller Area
Network (eCAN) Modules
– One Inter-Integrated-Circuit (I2C) Bus
12-Bit ADC, 16 Channels
– 2 x 8 Channel Input Multiplexer
– Two Sample-and-Hold
– Single/Simultaneous Conversions
– Fast Conversion Rate: 160 ns/6.25 MSPS
– Internal or External Reference
Up to 35 Individually Programmable,
Multiplexed General-Purpose Input/Output
(GPIO) Pins With Input Filtering
Advanced Emulation Features
– Analysis and Breakpoint Functions
– Real-Time Debug via Hardware
Low-Power Modes and Power Savings
– IDLE, STANDBY, HALT Modes Supported
– Disable Individual Peripheral Clocks
Package Options
– Thin Quad Flatpack (PZ)
– MicroStar BGA™ (GGM, ZGM)
Temperature Options:
– M: -55°C to 125°C (PZ)
MicroStar BGA, TMS320C28x, MicroStar, C28x, TMS320C2000, DSP/BIOS, Code Composer Studio, TMS320 are trademarks of Texas
Instruments.
eZdsp, XDS510USB are trademarks of Spectrum Digital.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2007, Texas Instruments Incorporated
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
2
Introduction
The SM320F2808, F2806, and F2801/UCD9501 devices, members of the TMS320C28x™ DSP
generation, are highly integrated, high-performance solutions for demanding control applications. The
UCD9501 is a 32-bit digital signal controller for power management.
Throughout this document, SM320F2808, F2806, and F2801/UCD9501 are abbreviated as F2808, F2806,
and F2801/9501, respectively. TMS320x280x device reference guides, flash tools, and other collateral are
applicable to the UCD9501 device as well. Table 2-1 provides a summary of each device's features.
Table 2-1. Hardware Features
F2808
F2806 (1)
F2801/9501 (1)
10 ns
10 ns
10 ns
18K
(L0, L1, M0, M1, H0)
10K
(L0, L1, M0, M1)
6K
(L0, M0, M1)
3.3-V on-chip flash (16-bit word)
64K
32K
16K
Code security for on-chip flash/SARAM/OTP blocks
Yes
Yes
Yes
Boot ROM (4K X16)
Yes
Yes
Yes
One-time programmable (OTP) ROM
Yes
Yes
Yes
External memory interface
No
No
No
ePWM1, ePWM2
ePWM3, ePWM4,
ePWM5, ePWM6
ePWM1, ePWM2
ePWM3, ePWM4,
ePWM5, ePWM6
ePWM1,
ePWM2,
ePWM3
ePWM1A, ePWM2A
ePWM3A, ePWM4A
ePWM1A, ePWM2A
ePWM3A, ePWM4A
ePWM1A, ePWM2A
ePWM3A
Enhanced 32-bit CAPTURE inputs or auxiliary PWM outputs
eCAP1, eCAP2
eCAP3, eCAP4
eCAP1, eCAP2
eCAP3, eCAP4
eCAP1, eCAP2
Enhanced 32-bit QEP channels (four inputs/channel)
FEATURE
Instruction cycle (at 100 MHz)
Single-access RAM (SARAM) (16-bit word)
Enhanced PWM outputs (16-bit timer-based modules with 2
PWM outputs/module)
HRPWM channels
eQEP1, eQEP2
eQEP1, eQEP2
eQEP1
Watchdog timer
Yes
Yes
Yes
12-Bit ADC channels
16
16
16
32-Bit CPU timers
3
3
3
Serial Peripheral Interface (SPI)
SPI-A, SPI-B,
SPI-C, SPI-D
SPI-A, SPI-B,
SPI-C, SPI-D
SPI-A, SPI-B
Serial Communications Interface (SCI)
SCI-A, SCI-B
SCI-A, SCI-B
SCI-A
eCAN-A, eCAN-B
eCAN-A
eCAN-A
I2C-A
I2C-A
I2C-A
35
35
35
Enhanced Controller Area Network (eCAN)
Inter-Integrated Circuit (I2C)
Digital I/O pins (shared)
External interrupts
3
3
3
Supply voltage
1.8-V Core, 3.3-V I/O
1.8-V Core, 3.3-V I/O
1.8-V Core, 3.3-V I/O
Packaging
100-Pin PZ
100-Ball GGM, ZGM
100-Pin PZ
100-Ball GGM, ZGM
100-Pin PZ
100-Ball GGM, ZGM
(PZ, GGM, ZGM)
(PZ, GGM, ZGM)
(PZ, GGM, ZGM)
(PZ, GGM, ZGM)
(PZ, GGM, ZGM)
(PZ, GGM, ZGM)
(PZ)
(PZ)
(PZ)
Temperature options
(1)
M: -55°C to 125°C
Product Preview
ORDERING INFORMATION
10
Introduction
TA
PACKAGE
ORDERABLE PART NUMBER
-55°C to 125°C
LQFP-PZ
SM320F2801PZMEP
-55°C to 125°C
LQFP-PZ
SM320F2808PZMEP
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
2.1
Pin Assignments
52
GPIO18/SPICLKA/SCITXDB
GPIO5/EPWM3B/SPICLKD/ECAP1
GPIO17/SPISOMIA/CANRXB/TZ6
GPIO4/EPWM3A
54
53
51
GPIO6/EPWM4A/EPWMSYNCI/EPWMSYNCO
VSS
56
55
GPIO7/EPWM4B/SPISTED/ECAP2
GPIO19/SPISTEA/SCIRXDB
57
59
58
GPIO9/EPWM5B/SCITXDB/ECAP3
GPIO8/EPWM5A/CANTXB/ADCSOCAO
VDD
61
60
GPIO20/EQEP1A/SPISIMOC/CANTXB
VSS
63
62
GPIO10/EPWM6A/CANRXB/ADCSOCBO
64
65
GPIO21/EQEP1B/SPISOMIC/CANRXB
XCLKOUT
VDDIO
66
68
67
GPIO11/EPWM6B/SCIRXDB/ECAP4
VSS
VDD
69
70
71
TDI
GPIO23/EQEP1I/SPISTEC/SCIRXDB
GPIO22/EQEP1S/SPICLKC/SCITXDB
73
72
TCK
TMS
75
74
The SM320F2808, F2806, and F2801/UCD9501 100-pin PZ low-profile quad flatpack (LQFP) pin
assignments are shown in Figure 2-1, Figure 2-2 and Figure 2-3. Table 2-2 describes the function(s) of
each pin.
VDD
X2
85
41
VSS
86
40
VSS
X1
87
39
VDD2A18
VSS2AGND
88
38
ADCRESEXT
VSS
89
37
XCLKIN
90
36
ADCREFP
ADCREFM
GPIO25/ECAP2/EQEP2B/SPISOMIB
91
35
GPIO28/SCIRXDA/TZ5
VDD
92
34
93
33
VSS
94
32
GPIO13/TZ2/CANRXB/SPISOMIB
VDD3VFL
95
31
96
30
TEST1
TEST2
97
29
ADCINB3
ADCINB2
98
28
ADCINB1
GPIO26/ECAP3/EQEP2I/SPICLKB
99
27
100
26
ADCINB0
VDDAIO
19
ADCINA4
ADCINA3
ADCINA2
ADCINA1
18
ADCINA7
ADCINA6
ADCINA5
15
16
VSSA2
VDDA2
13
VSS1AGND
11
12
9
GPIO15/TZ4/SCIRXDB/SPISTEB
VDD
VSS
VDD1A18
GPIO33/SCLA/EPWMSYNCO/ADCSOCBO
GPIO30/CANRXA
GPIO31/CANTXA
GPIO14/TZ3/SCITXDB/SPICLKB
GPIO29/SCITXDA/TZ6
VSS
VDDIO
GPIO12/TZ1/CANTXB/SPISIMOB
GPIO32/SDAA/EPWMSYNCI/ADCSOCAO
24
GPIO34
VDD
25
42
VSSAIO
43
84
ADCLO
83
TRST
22
GPIO24/ECAP1/EQEP2A/SPISIMOB
23
44
ADCINA0
45
82
20
81
21
46
EMU1
VDDIO
17
80
GPIO3/EPWM2B/SPISOMID
GPIO0/EPWM1A
VDDIO
14
47
10
79
8
GPIO27/ECAP4/EQEP2S/SPISTEB
EMU0
7
48
5
78
6
VSS
XRS
3
GPIO16/SPISIMOA/CANTXB/TZ5
49
4
50
77
1
76
2
TDO
VSS
GPIO2/EPWM2A
GPIO1/EPWM1B/SPISIMOD
ADCREFIN
ADCINB7
ADCINB6
ADCINB5
ADCINB4
Figure 2-1. SM320F2808 100-Pin PZ LQFP (Top View)
Submit Documentation Feedback
Introduction
11
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
GPIO4/EPWM3A
51
52
GPIO18/SPICLKA/SCITXDB
GPIO5/EPWM3B/SPICLKD/ECAP1
GPIO17/SPISOMIA/TZ6
54
53
GPIO6/EPWM4A/EPWMSYNCI/EPWMSYNCO
VSS
56
55
GPIO7/EPWM4B/SPISTED/ECAP2
GPIO19/SPISTEA/SCIRXDB
GPIO8/EPWM5A/ADCSOCAO
VDD
58
GPIO9/EPWM5B/SCITXDB/ECAP3
61
60
57
GPIO20/EQEP1A/SPISIMOC
VSS
59
GPIO10/EPWM6A/ADCSOCBO
64
63
62
XCLKOUT
VDDIO
66
65
GPIO21/EQEP1B/SPISOMIC
67
68
GPIO11/EPWM6B/SCIRXDB/ECAP4
VSS
VDD
69
70
71
TDI
GPIO23/EQEP1I/SPISTEC/SCIRXDB
GPIO22/EQEP1S/SPICLKC/SCITXDB
73
72
TCK
TMS
75
74
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
50
GPIO16/SPISIMOA/TZ5
77
49
VSS
78
48
GPIO3/EPWM2B/SPISOMID
79
47
EMU0
EMU1
VDDIO
80
46
GPIO0/EPWM1A
VDDIO
81
45
GPIO2/EPWM2A
82
44
GPIO24/ECAP1/EQEP2A/SPISIMOB
TRST
83
43
84
42
GPIO1/EPWM1B/SPISIMOD
GPIO34
VDD
VDD
85
41
VSS
X2
VSS
86
40
87
39
VDD2A18
VSS2AGND
X1
VSS
88
38
ADCRESEXT
89
37
ADCREFP
XCLKIN
90
36
ADCREFM
GPIO25/ECAP2/EQEP2B/SPISOMIB
91
35
GPIO28/SCIRXDA/TZ5
VDD
92
34
ADCREFIN
ADCINB7
93
33
ADCINB6
VSS
GPIO13/TZ2/SPISOMIB
VDD3VFL
94
32
ADCINB5
95
31
ADCINB4
96
30
TEST1
TEST2
97
29
ADCINB3
ADCINB2
98
TDO
VSS
XRS
76
GPIO27/ECAP4/EQEP2S/SPISTEB
24
25
23
22
ADCINA1
ADCINA0
ADCLO
VSSAIO
20
21
ADCINA3
ADCINA2
18
19
ADCINA5
17
ADCINA6
ADCINA4
15
14
VSSA2
16
12
13
VDD1A18
VSS1AGND
VDDA2
11
VSS
ADCINA7
10
8
GPIO31/CANTXA
GPIO14/TZ3/SCITXDB/SPICLKB
9
7
GPIO30/CANRXA
GPIO15/TZ4/SCIRXDB/SPISTEB
VDD
5
6
GPIO33/SCLA/EPWMSYNCO/ADCSOCBO
2
3
ADCINB0
VDDAIO
4
26
VDDIO
100
GPIO29/SCITXDA/TZ6
ADCINB1
27
1
28
99
GPIO12/TZ1/SPISIMOB
VSS
GPIO26/ECAP3/EQEP2I/SPICLKB
GPIO32/SDAA/EPWMSYNCI/ADCSOCAO
Figure 2-2. F2806 100-Pin PZ LQFP (Top View)
12
Introduction
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
GPIO17/SPISOMIA/TZ6
GPIO4/EPWM3A
52
51
54
53
56
55
GPIO7/ECAP2
GPIO19/SPISTEA
GPIO6/EPWMSYNCI/EPWMSYNCO
VSS
GPIO18/SPICLKA
GPIO5/EPWM3B/ECAP1
58
57
GPIO8/ADCSOCAO
VDD
59
61
60
GPIO20/EQEP1A
VSS
GPIO9
62
GPIO10/ADCSOCBO
64
63
GPIO21/EQEP1B
XCLKOUT
VDDIO
65
66
68
GPIO11
VSS
VDD
67
GPIO22/EQEP1S
71
70
69
TDI
GPIO23/EQEP1I
73
72
TCK
TMS
75
74
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
GPIO16/SPISIMOA/TZ5
VSS
TDO
VSS
76
50
77
49
XRS
GPIO27
78
48
79
47
EMU0
80
46
EMU1
VDDIO
81
45
82
44
GPIO24/ECAP1
TRST
83
43
84
42
VDD
85
41
VSS
X2
VSS
86
40
87
39
VDD2A18
VSS2AGND
GPIO3/EPWM2B
GPIO0/EPWM1A
VDDIO
GPIO2/EPWM2A
GPIO1/EPWM1B
GPIO34
VDD
ADCINB1
27
100
26
ADCINB0
VDDAIO
17
ADCINA6
25
15
16
ADCINA7
8
GPIO14/TZ3
GPIO15/TZ4
VDD
VDD1A18
VSS1AGND
VSSA2
VDDA2
7
GPIO31/CANTXA
9
5
6
GPIO30/CANRXA
VDDIO
GPIO29/SCITXDA/TZ6
GPIO33/SCLA/EPWMSYNCO/ADCSOCBO
24
28
99
ADCLO
VSSAIO
98
GPIO26
GPIO32/SDAA/EPWMSYNCI/ADSOCAO
22
ADCINB3
ADCINB2
23
29
ADCINA1
TEST1
TEST2
ADCINA0
30
97
20
96
21
ADCINB4
VDD3VFL(A)
ADCINA3
31
ADCINA2
95
18
ADCINB5
GPIO13/TZ2
19
ADCINB6
32
ADCINA5
33
94
ADCINA4
ADCREFIN
ADCINB7
14
34
93
12
92
13
35
11
91
VSS
ADCREFM
GPIO25/ECAP2/SPISIMIB
GPIO28/SCIRXDA/TZ5
VDD
VSS
10
36
3
90
4
ADCREFP
XCLKIN
1
ADCRESEXT
37
2
38
89
VSS
88
GPIO12/TZ1
X1
VSS
Figure 2-3. F2801/UCD9501 100-Pin PZ LQFP (Top View)
Submit Documentation Feedback
Introduction
13
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
K
J
H
G
F
E
D
C
B
A
ADCINB0
ADCINB3
ADCINB5
ADCINB7
VSS2AGND
GPIO1
GPIO0
VSS
GPIO16
ADCLO
VDDAIO
ADCINB1
ADCINB4
ADCREFIN
VDD2A18
GPIO2
GPIO3
GPIO4
GPIO17
ADCINA1
ADCINA0
ADCINB2
ADCINB6
ADCREFM
VSS
VDDIO
GPIO18
GPIO5
VSS
ADCINA4
ADCINA3
ADCINA2
ADCINA5
ADCREFP
VDD
GPIO34
GPIO7
GPIO6
GPIO19
VSSA2
VDDA2
ADCINA7
ADCINA6
ADCRESEXT
GPIO20
VSS
GPIO9
GPIO8
VDD
GPIO15
VDD
VSS
VDD1A18
VSS1AGND
X1
GPIO21
XCLKOUT
VDDIO
GPIO10
GPIO31
GPIO30
GPIO14
VDD
GPIO28
VSS
VDD
GPIO22
GPIO11
VSS
GPIO33
VDDIO
GPIO29
VDD3VFL
GPIO25
X2
GPIO24
GPIO27
TDI
GPIO23
VSS
GPIO12
TEST2
GPIO13
XCLKIN
VDD
EMU1
XRS
TDO
TMS
GPIO32
GPIO26
TEST1
VSS
VSS
TRST
VDDIO
EMU0
VSS
TCK
1
2
3
4
5
6
7
8
9
10
VSSAIO
Bottom View
Figure 2-4. SM320F280x 100-Ball GGM and ZGM MicroStar™ BGA (Bottom View)
2.2
Signal Descriptions
Table 2-2 describes the signals on the 280x devices. All digital inputs are TTL-compatible. All outputs are
3.3 V with CMOS levels. Inputs are not 5-V tolerant.
14
Introduction
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 2-2. Signal Descriptions
PIN NO.
NAME
PZ PIN
#
DESCRIPTION
GGM
BALL #
(1)
JTAG
TRST
84
A6
JTAG test reset with internal pulldown. TRST, when driven high, gives the scan system control of
the operations of the device. If this signal is not connected or driven low, the device operates in its
functional mode, and the test reset signals are ignored.
NOTE: Do not use pullup resistors on TRST; it has an internal pull-down device. TRST is an active
high test pin and must be maintained low at all times during normal device operation. In a low-noise
environment, TRST may be left floating. In other instances, an external pulldown resistor is highly
recommended. The value of this resistor should be based on drive strength of the debugger pods
applicable to the design. A 2.2-kΩ resistor generally offers adequate protection. Since this is
application-specific, it is recommended that each target board is validated for proper operation of
the debugger and the application. (I, ↓)
TCK
75
A10
JTAG test clock with internal pullup (I, ↑)
TMS
74
B10
JTAG test-mode select (TMS) with internal pullup. This serial control input is clocked into the TAP
controller on the rising edge of TCK. (I, ↑)
TDI
73
C9
JTAG test data input (TDI) with internal pullup. TDI is clocked into the selected register (instruction
or data) on a rising edge of TCK. (I, ↑)
TDO
76
B9
JTAG scan out, test data output (TDO). The contents of the selected register (instruction or data)
are shifted out of TDO on the falling edge of TCK. (O/Z 8 mA drive)
EMU0
80
A8
Emulator pin 0. When TRST is driven high, this pin is used as an interrupt to or from the emulator
system and is defined as input/output through the JTAG scan. (I/O/Z, 8 mA drive ↑)
EMU1
81
B7
Emulator pin 1. When TRST is driven high, this pin is used as an interrupt to or from the emulator
system and is defined as input/output through the JTAG scan. (I/O/Z, 8 mA drive, ↑)
FLASH
VDD3VFL
96
C4
3.3-V Flash Core Power Pin. This pin should be connected to 3.3 V at all times.
TEST1
97
A3
Test Pin. Reserved for Texas Instruments. Must be left unconnected. (I/O)
TEST2
98
B3
Test Pin. Reserved for Texas Instruments. Must be left unconnected. (I/O)
CLOCK
XCLKOUT
66
E8
Output clock derived from SYSCLKOUT. XCLKOUT is either the same frequency, one-half the
frequency, or one-fourth the frequency of SYSCLKOUT. This is controlled by the bits 1, 0
(XCLKOUTDIV) in the XCLK register. At reset, XCLKOUT = SYSCLKOUT/4. The XCLKOUT signal
can be turned off by setting XCLKOUTDIV to 3. Unlike other GPIO pins, the XCLKOUT pin is not
placed in high-impedance state during a reset. (O/Z, 8 mA drive).
XCLKIN
90
B5
External Oscillator Input. This pin is to feed a clock from an external 3.3-V oscillator. In this case,
the X1 pin must be tied to GND. If a crystal/resonator is used (or if an external 1.8-V oscillator is
used to feed clock to X1 pin), this pin must be tied to GND. (I)
X1
88
E6
Internal/External Oscillator Input. To use the internal oscillator, a quartz crystal or a ceramic
resonator may be connected across X1 and X2. The X1 pin is referenced to the 1.8-V core digital
power supply. A 1.8-V external oscillator may be connected to the X1 pin. In this case, the XCLKIN
pin must be connected to ground. If a 3.3-V external oscillator is used with the XCLKIN pin, X1 must
be tied to GND. (I)
X2
86
C6
Internal Oscillator Output. A quartz crystal or a ceramic resonator may be connected across X1 and
X2. If X2 is not used it must be left unconnected. (O)
RESET
XRS
78
B8
Device Reset (in) and Watchdog Reset (out).
Device reset. XRS causes the device to terminate execution. The PC will point to the address
contained at the location 0x3FFFC0. When XRS is brought to a high level, execution begins at the
location pointed to by the PC. This pin is driven low by the DSP when a watchdog reset occurs.
During watchdog reset, the XRS pin is driven low for the watchdog reset duration of 512 OSCCLK
cycles. (I/OD, ↑)
The output buffer of this pin is an open-drain with an internal pullup (100 µA, typical). It is
recommended that this pin be driven by an open-drain device.
ADCINA7
16
F3
ADC Group A, Channel 7 input (I)
ADCINA6
17
F4
ADC Group A, Channel 6 input (I)
ADC SIGNALS
(1)
I = Input, O = Output, Z = High impedance, OD = Open drain, ↑ = Pullup, ↓ = Pulldown
Submit Documentation Feedback
Introduction
15
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 2-2. Signal Descriptions (continued)
PIN NO.
NAME
DESCRIPTION
(1)
PZ PIN
#
GGM
BALL #
ADCINA5
18
G4
ADC Group A, Channel 5 input (I)
ADCINA4
19
G1
ADC Group A, Channel 4 input (I)
ADCINA3
20
G2
ADC Group A, Channel 3 input (I)
ADCINA2
21
G3
ADC Group A, Channel 2 input (I)
ADCINA1
22
H1
ADC Group A, Channel 1 input (I)
ADCINA0
23
H2
ADC Group A, Channel 0 input (I)
ADCINB7
34
K5
ADC Group B, Channel 7 input (I)
ADCINB6
33
H4
ADC Group B, Channel 6 input (I)
ADCINB5
32
K4
ADC Group B, Channel 5 input (I)
ADCINB4
31
J4
ADC Group B, Channel 4 input (I)
ADCINB3
30
K3
ADC Group B, Channel 3 input (I)
ADCINB2
29
H3
ADC Group B, Channel 2 input (I)
ADCINB1
28
J3
ADC Group B, Channel 1 input (I)
ADCINB0
27
K2
ADC Group B, Channel 0 input (I)
ADCLO
24
J1
Low Reference (connect to analog ground) (I)
ADCRESEXT
38
F5
ADC External Current Bias Resistor. Connect a 22-kΩ resistor to analog ground.
ADCREFIN
35
J5
External reference input (I)
ADCREFP
37
G5
Internal Reference Positive Output. Requires a low ESR (50 mΩ - 1.5 Ω) ceramic bypass capacitor
of 2.2 µF to analog ground. (O)
ADCREFM
36
H5
Internal Reference Medium Output. Requires a low ESR (50 mΩ - 1.5 Ω) ceramic bypass capacitor
of 2.2 µF to analog ground. (O)
VDDA2
15
F2
ADC Analog Power Pin (3.3 V)
VSSA2
14
F1
ADC Analog Ground Pin
VDDAIO
26
J2
ADC Analog I/O Power Pin (3.3 V)
VSSAIO
25
K1
ADC Analog I/O Ground Pin
VDD1A18
12
E4
ADC Analog Power Pin (1.8 V)
VSS1AGND
13
E5
ADC Analog Ground Pin
VDD2A18
40
J6
ADC Analog Power Pin (1.8 V)
VSS2AGND
39
K6
ADC Analog Ground Pin
VDD
10
E2
VDD
42
G6
VDD
59
F10
VDD
68
D7
VDD
85
B6
VDD
93
D4
VDDIO
3
C2
VDDIO
46
H7
VDDIO
65
E9
VDDIO
82
A7
CPU AND I/O POWER PINS
16
Introduction
CPU and Logic Digital Power Pins (1.8 V)
Digital I/O Power Pin (3.3 V)
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 2-2. Signal Descriptions (continued)
PIN NO.
NAME
PZ PIN
#
GGM
BALL #
VSS
2
B1
VSS
11
E3
VSS
41
H6
VSS
49
K9
VSS
55
H10
VSS
62
F7
VSS
69
D10
VSS
77
A9
VSS
87
D6
VSS
89
A5
VSS
94
A4
DESCRIPTION
(1)
Digital Ground Pins
GPIOA AND PERIPHERAL SIGNALS (2)
GPIO0
EPWM1A
GPIO1
EPWM1B
SPISIMOD
GPIO2
EPWM2A
GPIO3
EPWM2B
SPISOMID
GPIO4
EPWM3A
GPIO5
EPWM3B
SPICLKD
ECAP1
GPIO6
EPWM4A
EPWMSYNCI
EPWMSYNCO
GPIO7
EPWM4B
SPISTED
ECAP2
GPIO8
EPWM5A
CANTXB
ADCSOCAO
GPIO9
EPWM5B
SCITXDB
ECAP3
(2)
(3)
47
44
K8
General purpose input/output 0 (I/O/Z) (3)
Enhanced PWM1 Output A and HRPWM channel (O)
-
K7
General purpose input/output 1 (I/O/Z) (3)
Enhanced PWM1 Output B (O)
SPI-D slave in, master out (I/O) (not available on F2801/9501)
-
J7
General purpose input/output 2 (I/O/Z) (3)
Enhanced PWM2 Output A and HRPWM channel (O)
-
J8
General purpose input/output 3 (I/O/Z) (3)
Enhanced PWM2 Output B (O)
SPI-D slave out, master in (I/O) (not available on F2801/9501)
-
J9
General purpose input/output 4 (I/O/Z) (3)
Enhanced PWM3 output A and HRPWM channel (O)
-
H9
General purpose input/output 5 (I/O/Z) (3)
Enhanced PWM3 output B (O)
SPI-D clock (I/O) (not available on F2801/9501)
Enhanced capture input/output 1 (I/O)
G9
General purpose input/output 6 (I/O/Z) (3)
Enhanced PWM4 output A and HRPWM channel (not available on F2801/9501) (O)
External ePWM sync pulse input (I)
External ePWM sync pulse output (O)
G8
General purpose input/output 7 (I/O/Z) (3)
Enhanced PWM4 output B (not available on F2801/9501) (O)
SPI-D slave transmit enable (not available on F2801/9501 (I/O)
Enhanced capture input/output 2 (I/O)
F9
General purpose input/output 8 (I/O/Z) (3)
Enhanced PWM5 output A (not available on F2801/9501) (O)
Enhanced CAN-B transmit (not available on F2806/F2801/9501) (O)
ADC start-of-conversion A (O)
F8
General purpose input/output 9 (I/O/Z) (3)
Enhanced PWM5 output B (not available on F2801/9501) (O)
SCI-B transmit data (not available on F2801/9501) (O)
Enhanced capture input/output 3 (not available on F2801/9501) (I/O)
45
48
51
53
56
58
60
61
All GPIO pins are I/O/Z, 4-mA drive typical (unless otherwise indicated), and have an internal pullup, which can be selectively
enabled/disabled on a per-pin basis. This feature only applies to the GPIO pins. The GPIO function (shown in Italics) is the default at
reset. The peripheral signals that are listed under them are alternate functions.
The pullups on GPIO0-GPIO11 pins are not enabled at reset.
Submit Documentation Feedback
Introduction
17
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 2-2. Signal Descriptions (continued)
PIN NO.
NAME
GPIO10
EPWM6A
CANRXB
ADCSOCBO
GPIO11
EPWM6B
SCIRXDB
ECAP4
GPIO12
TZ1
CANTXB
SPISIMOB
GPIO13
TZ2
CANRXB
SPISOMIB
GPIO14
TZ3
SCITXDB
SPICLKB
GPIO15
TZ4
SCIRXDB
SPISTEB
GPIO16
SPISIMOA
CANTXB
TZ5
GPIO17
SPISOMIA
CANRXB
TZ6
GPIO18
SPICLKA
SCITXDB
GPIO19
SPISTEA
SCIRXDB
GPIO20
EQEP1A
SPISIMOC
CANTXB
GPIO21
EQEP1B
SPISOMIC
CANRXB
GPIO22
EQEP1S
SPICLKC
SCITXDB
GPIO23
EQEP1I
SPISTEC
SCIRXDB
(4)
18
PZ PIN
#
64
70
1
95
8
9
50
52
54
57
63
67
71
72
DESCRIPTION
GGM
BALL #
(1)
E10
General purpose input/output 10 (I/O/Z) (3)
Enhanced PWM6 output A (not available on F2801/9501) (O)
Enhanced CAN-B receive (not available on F2806/F2801/9501) (I)
ADC start-of-conversion B (O)
D9
General purpose input/output 11 (I/O/Z) (3)
Enhanced PWM6 output B (not available on F2801/9501) (O)
SCI-B receive data (not available on F2801/9501) (I)
Enhanced CAP Input/Output 4 (not available on F2801/9501) (I/O)
B2
General purpose input/output 12 (I/O/Z) (4)
Trip Zone input 1 (I)
Enhanced CAN-B transmit (not available on F2806/F2801/9501) (O)
SPI-B Slave in, Master out (I/O)
B4
General purpose input/output 13 (I/O/Z) (4)
Trip zone input 2 (I)
Enhanced CAN-B receive (not available on F2806/F2801/9501) (I)
SPI-B slave out, master in (I/O)
D3
General purpose input/output 14 (I/O/Z) (4)
Trip zone input 3 (I)
SCI-B transmit (not available on F2801/9501) (O)
SPI-B clock input/output (I/O)
E1
General purpose input/output 15 (I/O/Z) (4)
Trip zone input (I)
SCI-B receive (not available on F2801/9501) (I)
SPI-B slave transmit enable (I/O)
K10
General purpose input/output 16 (I/O/Z) (4)
SPI-A slave in, master out (I/O)
Enhanced CAN-B transmit (not available on F2806/F2801/9501) (O)
Trip zone input 5 (I)
J10
General purpose input/output 17 (I/O/Z) (4)
SPI-A slave out, master in (I/O)
Enhanced CAN-B receive (not available on F2806/F2801/9501) (I)
Trip zone input 6(I)
H8
General purpose input/output 18 (I/O/Z) (4)
SPI-A clock input/output (I/O)
SCI-B transmit (not available on F2801/9501) (O)
-
G10
General purpose input/output 19 (I/O/Z) (4)
SPI-A slave transmit enable input/output (I/O)
SCI-B receive (not available on F2801/9501) (I)
-
F6
General purpose input/output 20 (I/O/Z) (4)
Enhanced QEP1 input A (I)
SPI-C slave in, master out (not available on F2801/9501) (I/O)
Enhanced CAN-B transmit (not available on F2806/F2801/9501) (O)
E7
General purpose input/output 21 (I/O/Z) (4)
Enhanced QEP1 input A (I)
SPI-C master in, slave out (not available on F2801/9501) (I/O)
Enhanced CAN-B receive (not available on F2806/F2801/9501) (I)
D8
General purpose input/output 22 (I/O/Z) (4)
Enhanced QEP1 strobe (I/O)
SPI-C clock (not available on F2801/9501) (I/O)
SCI-B transmit (not available on F2801/9501) (O)
C10
General purpose input/output 23 (I/O/Z) (4)
Enhanced QEP1 index (I/O)
SPI-C slave transmit enable (not available on F2801/9501) (I/O)
SCI-B receive (I) (not available on F2801/9501)
The pullups on GPIO12-GPIO34 are enabled upon reset.
Introduction
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 2-2. Signal Descriptions (continued)
PIN NO.
NAME
GPIO24
ECAP1
EQEP2A
SPISIMOB
GPIO25
ECAP2
EQEP2B
SPISOMIB
GPIO26
ECAP3
EQEP2I
SPICLKB
GPIO27
ECAP4
EQEP2S
SPISTEB
GPIO28
SCIRXDA
TZ5
GPIO29
SCITXDA
TZ6
GPIO30
CANRXA
GPIO31
CANTXA
GPIO32
SDAA
EPWMSYNCI
ADCSOCAO
GPIO33
SCLA
EPWMSYNCO
ADCSOCBO
GPIO34
-
PZ PIN
#
83
91
99
79
92
4
6
7
100
5
43
GGM
BALL #
DESCRIPTION
(1)
C7
General purpose input/output 24 (I/O/Z) (4)
Enhanced capture 1 (I/O)
Enhanced QEP2 input A (I) (not available on F2801/9501)
SPI-B slave in, master out (I/O)
C5
General purpose input/output 25 (I/O/Z) (4)
Enhanced capture 2 (I/O)
Enhanced QEP2 input B (I) (not available on F2801/9501)
SPI-B master in, slave out (I/O)
A2
General purpose input/output 26 (I/O/Z) (4)
Enhanced capture 3 (I/O) (not available on F2801/9501)
Enhanced QEP2 index (I/O) (not available on F2801/9501)
SPI-B clock (I/O)
C8
General purpose input/output 27 (I/O/Z) (4)
Enhanced capture 4 (I/O) (not available on F2801/9501)
Enhanced QEP2 strobe (I/O) (not available on F2801)
SPI-B slave transmit enable (I/O)
D5
General purpose input/output 28. This pin has an 8-mA (typical) output buffer. (I/O/Z) (4)
SCI receive data (I)
Trip zone 5 (I)
C3
General purpose input/output 29. This pin has an 8-mA (typical) output buffer. (I/O/Z) (4)
SCI transmit data (O)
Trip zone 6 (I)
D2
General purpose input/output 30. This pin has an 8-mA (typical) output buffer. (I/O/Z) (4)
Enhanced CAN-A receive data (I)
-
D1
General purpose input/output 31. This pin has an 8-mA (typical) output buffer. (I/O/Z) (4)
Enhanced CAN-A transmit data (O)
-
A1
General purpose input/output 32 (I/O/Z) (4)
I2C data open-drain bidirectional port (I/OD)
Enhanced PWM external sync pulse input (I)
ADC start-of-conversion (O)
C1
General-Purpose Input/Output 33 (I/O/Z) (4)
I2C clock open-drain bidirectional port (I/OD)
Enhanced PWM external synch pulse output (O)
ADC start-of-conversion (O)
G7
General-Purpose Input/Output 34 (I/O/Z) (4)
-
Submit Documentation Feedback
Introduction
19
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
3
Functional Overview
Memory Bus
TINT0
32-bit CPU TIMER 0
TINT1
7
32-bit CPU TIMER 1
TINT2
Real-Time JTAG
(TDI, TDO, TRST, TCK,
TMS, EMU0, EMU1)
32-bit CPU TIMER 2
INT14
PIE
(96 Interrupts)(A)
INT[12:1]
M0 SARAM
1 K 16
NMI, INT13
External Interrupt
Control
32
4
SCI-A/B
FIFO
2
GPIOs
(35)
GPIO MUX
4
FIFO
I2C-A
FIFO
L1 SARAM(B)
4 K 16
(0-wait)
eCAN-A/B (32 mbox)
8
H0 SARAM(C)
8 K 16
(0-wait)
eQEP1/2
4
eCAP1/2/3/4
(4 timers 32-bit)
12
C28x CPU
(100 MHz)
ePWM1/2/3/4/5/6
(12 PWM outputs,
6 trip zones,
6 timers 16-bit)
6
32
SYSCLKOUT
System Control
XCLKOUT
XRS
XCLKIN
X1
X2
RS
(Oscillator, PLL,
Peripheral Clocking,
Low Power Modes,
WatchDog)
M1 SARAM
1 K 16
L0 SARAM
4 K 16
(0-wait)
16
SPI-A/B/C/D
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
CLKIN
ROM
32K x 16 (C2802)
16K x 16 (C2801)
FLASH
128K x 16 (F2809)
64K x 16 (F2808)
32K x 16 (F2806)
32K x 16 (F2802)
16K x 16 (F2801)
16K x 16 (9501)
16K x 16 (F2801x)
OTP(D)
1K 16
ADCSOCA/B
ÍÍÍ
ÍÍÍ
ÍÍÍ
ÍÍÍ
SOCA/B
Boot ROM
4 K 16
(1-wait state)
12-Bit ADC
16 Channels
Protected by the code-security module.
A.
43 of the possible 96 interrupts are used on the devices.
B.
Not available in F2801/9501
C.
Not available in F2806 or F2801/9501
Peripheral Bus
Figure 3-1. Functional Block Diagram
20
Functional Overview
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
3.1
Memory Map
Block Start
Address
Data Space
Prog Space
0x00 0000
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
M0 SARAM (1 K y 16)
0x00 0400
M1 SARAM (1 K y 16)
0x00 0800
Low 64K [0000 − FFFF]
(24x/240x equivalent data space)
Peripheral Frame 0
0x00 0D00
PIE Vector − RAM
(256 x 16)
(Enabled if ENPIE = 1)
0x00 0E00
0x00 6000
0x00 7000
Peripheral Frame 1
(protected)
Peripheral Frame 2
(protected)
0x00 8000
L0 SARAM (0-wait)
(4 k y 16, Secure Zone, Dual Mapped)
0x00 9000
0x00 A000
L1 SARAM (0-wait)
(4 k y 16, Secure Zone, Dual Mapped)
H0 SARAM (0-wait)
(8 k y 16, Dual Mapped)
0x00 C000
0x3D 7800
OTP
(1 k y 16, Secure Zone)
0x3D 7C00
0x3E 8000
High 64K [3F0000 − 3FFFFF]
(24x/240x equivalent program space)
FLASH
(64 k y 16, Secure Zone)
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
0x3F 7FF8
128-bit Password
0x3F 8000
L0 SARAM (0-wait)
(4 k y 16, Secure Zone, Dual Mapped)
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
0x3F 9000
0x3F A000
L1 SARAM (0-wait)
(4 k y 16, Secure Zone, Dual Mapped)
H0 SARAM (0-wait)
(8 k y 16, Dual Mapped)
0x3F C000
0x3F F000
Boot ROM (4 k y 16)
0x3F FFC0
Vectors (32 y 32)
(enabled if VMAP = 1, ENPIE = 0)
Reserved
A.
Memory blocks are not to scale.
B.
Peripheral Frame 0, Peripheral Frame 1, and Peripheral Frame 2 memory maps are restricted to data memory only.
User program cannot access these memory maps in program space.
C.
“ Protected” means the order of Write followed by Read operations is preserved rather than the pipeline order.
D.
Certain memory ranges are EALLOW protected against spurious writes after configuration.
Figure 3-2. F2808 Memory Map
Submit Documentation Feedback
Functional Overview
21
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Block Start
Address
Data Space
Prog Space
0x00 0000
ÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
M0 SARAM (1K y 16)
0x00 0400
M1 SARAM (1K y 16)
Low 64K [0000−FFFF]
(24x/240x equivalent data space)
0x00 0800
Peripheral Frame 0
0x00 0D00
PIE Vector − RAM
(256 x 16)
(Enabled if ENPIE = 1)
0x00 0E00
0x00 6000
Peripheral Frame 1
(protected)
0x00 7000
Peripheral Frame 2
(protected)
0x00 8000
0x00 9000
0x00 A000
0x3D 7800
L0 SARAM (0-wait)
(4k y 16, Secure Zone, Dual Mapped)
L1 SARAM (0-wait)
(4k y 16, Secure Zone, Dual Mapped)
OTP
(1 K y 16, Secure Zone)
0x3D 7C00
High 64K [3F0000 −3FFFF]
(24x/240x equivalent program space)
0x3F 0000
0x3F 7FF8
FLASH
(32 K y 16, Secure Zone)
128-bit Password
0x3F 8000
L0 SARAM (0-wait) (4k y 16,
Secure Zone, Dual Mapped)
0x3F 9000
L1 SARAM (0-wait) (4k y 16,
Secure Zone, Dual Mapped)
0x3F A000
0x3F F000
ÉÉÉÉ
ÉÉÉÉ
ÉÉÉÉ
ÉÉÉÉ
0x3F FFC0
Boot ROM (4 K y 16)
Vectors (32 y 32)
(enabled if VMAP = 1, ENPIE = 0)
Reserved
A.
Memory blocks are not to scale.
B.
Peripheral Frame 0, Peripheral Frame 1, and Peripheral Frame 2 memory maps are restricted to data memory only.
User program cannot access these memory maps in program space.
C.
“ Protected” means the order of Write followed by Read operations is preserved rather than the pipeline order.
D.
Certain memory ranges are EALLOW protected against spurious writes after configuration.
Figure 3-3. F2806 Memory Map
22
Functional Overview
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Block Start
Address
0x00 0000
Data Space
Prog Space
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉ
M0 SARAM (1K y 16)
0x00 0400
Low 64K [0000−FFFF]
(24x/240x equivalent data space)
M1 SARAM (1K y 16)
0x00 0800
Peripheral Frame 0
0x00 0D00
0x00 0E00
0x00 6000
0x00 7000
0x00 8000
0x00 9000
0x3D 7800
0x3D 7C00
High 64K [3F0000 −3FFFF]
(24x/240x equivalent program space)
0x3F 4000
0x3F 7FF8
PIE Vector − RAM
(256 x 16)
(Enabled if ENPIE = 1)
Peripheral Frame 1
(protected)
Peripheral Frame 2
(protected)
L0 SARAM (0-wait)
(4K y 16, Secure Zone, Dual Mapped)
OTP (F2801/9501 Only)(A)
(1K y 16, Secure Zone)
FLASH (F2801/9501) or ROM (C2801)
(16K y 16, Secure Zone)
128-bit Password
0x3F 8000
L0 (0-wait)
(4K y 16, Secure Zone, Dual Mapped)
0x3F 9000
0x3F F000
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
0x3F FFC0
Boot ROM (4K y 16)
Vectors (32 y 32)
(enabled if VMAP = 1, ENPIE = 0)
Reserved
A.
Memory blocks are not to scale.
B.
Peripheral Frame 0, Peripheral Frame 1, and Peripheral Frame 2 memory maps are restricted to data memory only.
User program cannot access these memory maps in program space.
C.
“ Protected” means the order of Write followed by Read operations is preserved rather than the pipeline order.
D.
Certain memory ranges are EALLOW protected against spurious writes after configuration.
Figure 3-4. F2801/9501 Memory Map
Submit Documentation Feedback
Functional Overview
23
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 3-1. Addresses of Flash Sectors in F2808
ADDRESS RANGE
PROGRAM AND DATA SPACE
0x3E 8000
0x3E BFFF
Sector D (16K x 16)
0x3E C000
0x3E FFFF
Sector C (16K x 16)
0x3F 0000
0x3F 3FFF
Sector B (16K x 16)
0x3F 4000
0x3F 7F7F
Sector A (16K x 16)
0x3F 7F80
0x3F 7FF5
Program to 0x0000 when using the
Code Security Module
0x3F 7FF6
0x3F 7FF7
Boot-to-Flash Entry Point
(program branch instruction here)
0x3F 7FF8
0x3F 7FFF
Security Password (128-Bit)
(Do not program to all zeros)
Table 3-2. Addresses of Flash Sectors in F2806
ADDRESS RANGE
PROGRAM AND DATA SPACE
0x3F 0000
0x3F 1FFF
Sector D (8K x 16)
0x3F 2000
0x3F 3FFF
Sector C (8K x 16)
0x3F 4000
0x3F 5FFF
Sector B (8K x 16)
0x3F 6000
0x3F 7F7F
Sector A (8K x 16)
0x3F 7F80
0x3F 7FF5
Program to 0x0000 when using the
Code Security Module
0x3F 7FF6
0x3F 7FF7
Boot-to-Flash Entry Point
(program branch instruction here)
0x3F 7FF8
0x3F 7FFF
Security Password (128-Bit)
(Do not program to all zeros)
Table 3-3. Addresses of Flash Sectors in F2801/9501
24
Functional Overview
ADDRESS RANGE
PROGRAM AND DATA SPACE
0x3F 4000
0x3F 4FFF
Sector D (4K x 16)
0x3F 5000
0x3F 5FFF
Sector C (4K x 16)
0x3F 6000
0x3F 6FFF
Sector B (4K x 16)
0x3F 7000
0x3F 7F7F
Sector A (4K x 16)
0x3F 7F80
0x3F 7FF5
Program to 0x0000 when using the
Code Security Module
0x3F 7FF6
0x3F 7FF7
Boot-to-Flash Entry Point
(program branch instruction here)
0x3F 7FF8
0x3F 7FFF
Security Password (128-Bit)
(Do not program to all zeros)
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
NOTE
For code security operation, all addresses between 0x3F7F80 and 0x3F7FF5 cannot be
used as program code or data, but must be programmed to 0x0000 when the
code-security passwords are programmed. If security is not a concern, addresses
0x3F7F80 through 0x3F7FEF may be used for code or data. Addresses 0x3F7FF0 –
0x3F7FF5 are reserved for data variables and should not contain program code.
Peripheral Frame 1 and Peripheral Frame 2 are grouped together so as to enable these blocks to be
write/read peripheral block protected. The protected mode ensures that all accesses to these blocks
happen as written. Because of the C28x pipeline, a write immediately followed by a read, to different
memory locations, appears in reverse order on the memory bus of the CPU. This can cause problems in
certain peripheral applications where the user expected the write to occur first (as written). The C28x CPU
supports a block protection mode where a region of memory can be protected so as to make sure that
operations occur as written (the penalty is extra cycles are added to align the operations). This mode is
programmable and by default, it protects the selected zones.
The wait states for the various spaces in the memory map area are listed in Table 3-4.
Table 3-4. Wait States
3.2
3.2.1
AREA
WAIT-STATES
COMMENTS
M0 and M1 SARAMs
0-wait
Fixed
Peripheral Frame 0
0-wait
Fixed
Peripheral Frame 1
0-wait (writes)
2-wait (reads)
Fixed. The eCAN peripheral can extend a cycle as needed.
Peripheral Frame 2
0-wait (writes)
2-wait (reads)
Fixed
L0 & L1 SARAMs
0-wait
OTP
Programmed via the Flash registers. 1-wait-state operation
Programmable,
is possible at a reduced CPU frequency. See Section
1-wait minimum
Section 3.2.5 for more information.
Flash
Programmed via the Flash registers. 0-wait-state operation
Programmable, is possible at reduced CPU frequency. The CSM password
0-wait minimum locations are hardwired for 16 wait-states. See Section
Section 3.2.5 for more information.
H0 SARAM
0-wait
Fixed
Boot-ROM
1-wait
Fixed
Brief Descriptions
C28x CPU
The C28x™ DSP generation is the newest member of the TMS320C2000™ DSP platform. The C28x is an
efficient C/C++ engine, hence enabling users to develop not only their system control software in a
high-level language, but also enables math algorithms to be developed using C/C++. The C28x is as
efficient in DSP math tasks as it is in system control tasks that typically are handled by microcontroller
devices. This efficiency removes the need for a second processor in many systems. The 32 x 32-bit MAC
capabilities of the C28x and its 64-bit processing capabilities, enable the C28x to efficiently handle higher
numerical resolution problems that would otherwise demand a more expensive floating-point processor
solution. Add to this the fast interrupt response with automatic context save of critical registers, resulting in
a device that is capable of servicing many asynchronous events with minimal latency. The C28x has an
8-level-deep protected pipeline with pipelined memory accesses. This pipelining enables the C28x to
execute at high speeds without resorting to expensive high-speed memories. Special branch-look-ahead
hardware minimizes the latency for conditional discontinuities. Special store conditional operations further
improve performance.
Submit Documentation Feedback
Functional Overview
25
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
3.2.2
Memory Bus (Harvard Bus Architecture)
As with many DSP type devices, multiple busses are used to move data between the memories and
peripherals and the CPU. The C28x memory bus architecture contains a program read bus, data read bus
and data write bus. The program read bus consists of 22 address lines and 32 data lines. The data read
and write busses consist of 32 address lines and 32 data lines each. The 32-bit-wide data busses enable
single cycle 32-bit operations. The multiple bus architecture, commonly termed "Harvard Bus", enables the
C28x to fetch an instruction, read a data value and write a data value in a single cycle. All peripherals and
memories attached to the memory bus will prioritize memory accesses. Generally, the priority of memory
bus accesses can be summarized as follows:
Highest:
Data Writes
(Simultaneous data and program writes cannot occur on the memory bus.)
Program Writes
(Simultaneous data and program writes cannot occur on the memory bus.)
Data Reads
Lowest:
3.2.3
Program Reads
(Simultaneous program reads and fetches cannot occur on the memory bus.)
Fetches
(Simultaneous program reads and fetches cannot occur on the memory bus.)
Peripheral Bus
To enable migration of peripherals between various Texas Instruments DSP family of devices, the 280x
devices adopt a peripheral bus standard for peripheral interconnect. The peripheral bus bridge multiplexes
the various busses that make up the processor Memory Bus into a single bus consisting of 16 address
lines and 16 or 32 data lines and associated control signals. Two versions of the peripheral bus are
supported on the 280x. One version only supports 16-bit accesses (called peripheral frame 2). The other
version supports both 16- and 32-bit accesses (called peripheral frame 1).
3.2.4
Real-Time JTAG and Analysis
The 280x implements the standard IEEE 1149.1 JTAG interface. Additionally, the 280x supports real-time
mode of operation whereby the contents of memory, peripheral and register locations can be modified
while the processor is running and executing code and servicing interrupts. The user can also single step
through non-time critical code while enabling time-critical interrupts to be serviced without interference.
The 280x implements the real-time mode in hardware within the CPU. This is a unique feature to the
280x, no software monitor is required. Additionally, special analysis hardware is provided which allows the
user to set hardware breakpoint or data/address watch-points and generate various user-selectable break
events when a match occurs.
3.2.5
Flash
The F2808 contains 64K x 16 of embedded flash memory, segregated into four 16K X 16 sectors. The
F2806 has 32K X 16 of embedded flash, segregated into four 8K X 16 sectors. The F2801/UCD9501
devices contain 16K X 16 of embedded Flash (four 4K X 16 sectors). All three devices also contain a
single 1K x 16 of OTP memory at address range 0x3D 7800 - 0x3D 7BFF. The user can individually
erase, program, and validate a flash sector while leaving other sectors untouched. However, it is not
possible to use one sector of the flash or the OTP to execute flash algorithms that erase/program other
sectors. Special memory pipelining is provided to enable the flash module to achieve higher performance.
The flash/OTP is mapped to both program and data space; therefore, it can be used to execute code or
store data information. Note that addresses 0x3F7FF0 - 0x3F7FF5 are reserved for data variables and
should not contain program code.
26
Functional Overview
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
NOTE
The F2808/F2806/F2801 Flash and OTP wait states can be configured by the application.
This allows applications running at slower frequencies to configure the flash to use fewer
wait states.
Flash effective performance can be improved by enabling the flash pipeline mode in the
Flash options register. With this mode enabled, effective performance of linear code
execution will be much faster than the raw performance indicated by the wait state
configuration alone. The exact performance gain when using the Flash pipeline mode is
application-dependent.
For more information on the Flash options, Flash wait-state, and OTP wait-state registers,
see the TMS320x280x System Control and Interrupts Reference Guide (literature number
SPRU712).
3.2.6
M0, M1 SARAMs
All 280x devices contain these two blocks of single access memory, each 1K x 16 in size. The stack
pointer points to the beginning of block M1 on reset. The M0 and M1 blocks, like all other memory blocks
on C28x devices, are mapped to both program and data space. Hence, the user can use M0 and M1 to
execute code or for data variables. The partitioning is performed within the linker. The C28x device
presents a unified memory map to the programmer. This makes for easier programming in high-level
languages.
3.2.7
L0, L1, H0 SARAMs
The F2808 contains an additional 16K x 16 of single-access RAM, divided into 3 blocks (L0-4K, L1-4K,
H0-8K). The F2806 contains an additional 8K x 16 of single-access RAM, divided into 2 blocks (L0-4K,
L1-4K). The F2801/UCD9501 contain an additional 4K x 16 of single-access RAM (L0-4K). Each block
can be independently accessed to minimize CPU pipeline stalls. Each block is mapped to both program
and data space.
3.2.8
Boot ROM
The Boot ROM is factory-programmed with boot-loading software. Boot-mode signals are provided to tell
the bootloader software what boot mode to use on power up. The user can select to boot normally or to
download new software from an external connection or to select boot software that is programmed in the
internal Flash. The Boot ROM also contains standard tables, such as SIN/COS waveforms, for use in
math related algorithms.
Table 3-5. Boot Mode Selection
MODE
DESCRIPTION
GPIO18
SPICLKA
SCITXDB
GPIO29
SCITXDA
GPIO34
Boot to Flash
Jump to Flash address 0x3F 7FF6
You must have programmed a branch instruction here prior
to reset to redirect code execution as desired.
1
1
1
SCI-A Boot
Load a data stream from SCI-A
1
1
0
SPI-A Boot
Load from an external serial SPI EEPROM on SPI-A
1
0
1
I2C Boot
Load data from an external EEPROM at address 0x50 on
the I2C bus
1
0
0
eCAN-A Boot
Call CAN_Boot to load from eCAN-A mailbox 1.
0
1
1
Boot to M0 SARAM
Jump to M0 SARAM address 0x00 0000.
0
1
0
Boot to OTP
Jump to OTP address 0x3D 7800
0
0
1
Parallel I/O Boot
Load data from GPIO0 - GPIO15
0
0
0
Submit Documentation Feedback
Functional Overview
27
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
3.2.9
Security
The 280x devices support high levels of security to protect the user firmware from being reverse
engineered. The security features a 128-bit password (hardcoded for 16 wait states), which the user
programs into the flash. One code security module (CSM) is used to protect the flash/OTP and the L0/L1
SARAM blocks. The security feature prevents unauthorized users from examining the memory contents
via the JTAG port, executing code from external memory or trying to boot-load some undesirable software
that would export the secure memory contents. To enable access to the secure blocks, the user must
write the correct 128-bit "KEY" value, which matches the value stored in the password locations within the
Flash.
NOTE
For code security operation, all addresses between 0x3F7F80 and 0x3F7FF5 cannot be
used as program code or data, but must be programmed to 0x0000 when the Code
Security Password is programmed. If security is not a concern, addresses 0x3F7F80
through 0x3F7FEF may be used for code or data. Addresses 0x3F7FF0 – 0x3F7FF5 are
reserved for data variables and should not contain program code.
The 128-bit password (at 0x3F 7FF8 - 0x3F 7FFF) must not be programmed to zeros.
Doing so would permanently lock the device.
NOTE
Code Security Module Disclaimer
The Code Security Module ("CSM") included on this device was designed to password
protect the data stored in the associated memory (either ROM or Flash) and is warranted
by Texas Instruments (Texas Instruments), in accordance with its standard terms and
conditions, to conform to TI's published specifications for the warranty period applicable
for this device.
Texas Instruments DOES NOT, HOWEVER, WARRANT OR REPRESENT THAT THE
CSM CANNOT BE COMPROMISED OR BREACHED OR THAT THE DATA STORED IN
THE ASSOCIATED MEMORY CANNOT BE ACCESSED THROUGH OTHER MEANS.
MOREOVER, EXCEPT AS SET FORTH ABOVE, Texas Instruments MAKES NO
WARRANTIES OR REPRESENTATIONS CONCERNING THE CSM OR OPERATION
OF THIS DEVICE, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL Texas Instruments BE LIABLE FOR ANY CONSEQUENTIAL,
SPECIAL, INDIRECT, INCIDENTAL, OR PUNITIVE DAMAGES, HOWEVER CAUSED,
ARISING IN ANY WAY OUT OF YOUR USE OF THE CSM OR THIS DEVICE,
WHETHER OR NOT Texas Instruments HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED TO
LOSS OF DATA, LOSS OF GOODWILL, LOSS OF USE OR INTERRUPTION OF
BUSINESS OR OTHER ECONOMIC LOSS.
3.2.10
Peripheral Interrupt Expansion (PIE) Block
The PIE block serves to multiplex numerous interrupt sources into a smaller set of interrupt inputs. The
PIE block can support up to 96 peripheral interrupts. On the 280x, 43 of the possible 96 interrupts are
used by peripherals. The 96 interrupts are grouped into blocks of 8 and each group is fed into 1 of 12
CPU interrupt lines (INT1 to INT12). Each of the 96 interrupts is supported by its own vector stored in a
dedicated RAM block that can be overwritten by the user. The vector is automatically fetched by the CPU
on servicing the interrupt. It takes 8 CPU clock cycles to fetch the vector and save critical CPU registers.
Hence the CPU can quickly respond to interrupt events. Prioritization of interrupts is controlled in
hardware and software. Each individual interrupt can be enabled/disabled within the PIE block.
28
Functional Overview
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
3.2.11
External Interrupts (XINT1, XINT2, XNMI)
The 280x supports three masked external interrupts (XINT1, XINT2, XNMI). XNMI can be connected to
the INT13 or NMI interrupt of the CPU. Each of the interrupts can be selected for negative, positive, or
both negative and positive edge triggering and can also be enabled/disabled (including the XNMI). The
masked interrupts also contain a 16-bit free running up counter, which is reset to zero when a valid
interrupt edge is detected. This counter can be used to accurately time stamp the interrupt. Unlike the
281x devices, there are no dedicated pins for the external interrupts. Rather, any Port A GPIO pin can be
configured to trigger any external interrupt.
3.2.12
Oscillator and PLL
The 280x can be clocked by an external oscillator or by a crystal attached to the on-chip oscillator circuit.
A PLL is provided supporting up to 10 input-clock-scaling ratios. The PLL ratios can be changed on-the-fly
in software, enabling the user to scale back on operating frequency if lower power operation is desired.
Refer to the Electrical Specification section for timing details. The PLL block can be set in bypass mode.
3.2.13
Watchdog
The 280x devices contain a watchdog timer. The user software must regularly reset the watchdog counter
within a certain time frame; otherwise, the watchdog will generate a reset to the processor. The watchdog
can be disabled if necessary.
3.2.14
Peripheral Clocking
The clocks to each individual peripheral can be enabled/disabled so as to reduce power consumption
when a peripheral is not in use. Additionally, the system clock to the serial ports (except eCAN) and the
ADC blocks can be scaled relative to the CPU clock. This enables the timing of peripherals to be
decoupled from increasing CPU clock speeds.
3.2.15
Low-Power Modes
The 280x devices are full static CMOS devices. Three low-power modes are provided:
3.2.16
IDLE:
Place CPU into low-power mode. Peripheral clocks may be turned off selectively and only
those peripherals that need to function during IDLE are left operating. An enabled interrupt
from an active peripheral or the watchdog timer will wake the processor from IDLE mode.
STANDBY:
Turn off clock to CPU and peripherals. This mode leaves the oscillator and PLL functional.
An external interrupt event will wake the processor and the peripherals. Execution begins
on the next valid cycle after detection of the interrupt event
HALT:
Turn off oscillator. This mode basically shuts down the device and places it in the lowest
possible power consumption mode. A reset or external signal can wake the device from
this mode.
Peripheral Frames 0, 1, 2 (PFn)
The 280x segregate peripherals into three sections. The mapping of peripherals is as follows:
PF0:
PF1:
PIE:
PIE Interrupt Enable and Control Registers Plus PIE Vector Table
Flash:
Flash Control, Programming, Erase, Verify Registers
Timers:
CPU-Timers 0, 1, 2 Registers
CSM:
Code Security Module KEY Registers
ADC:
ADC Result Registers (dual-mapped)
eCAN:
eCAN Mailbox and Control Registers
GPIO:
GPIO MUX Configuration and Control Registers
ePWM:
Enhanced Pulse Width Modulator Module and Registers
Submit Documentation Feedback
Functional Overview
29
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
PF2:
eCAP:
Enhanced Capture Module and Registers
eQEP:
Enhanced Quadrature Encoder Pulse Module and Registers
SYS:
System Control Registers
SCI:
Serial Communications Interface (SCI) Control and RX/TX Registers
SPI:
Serial Port Interface (SPI) Control and RX/TX Registers
ADC:
ADC Status, Control, and Result Register
2
I C:
3.2.17
Inter-Integrated Circuit Module and Registers
General-Purpose Input/Output (GPIO) Multiplexer
Most of the peripheral signals are multiplexed with general-purpose input/output (GPIO) signals. This
enables the user to use a pin as GPIO if the peripheral signal or function is not used. On reset, GPIO pins
are configured as inputs. The user can individually program each pin for GPIO mode or peripheral signal
mode. For specific inputs, the user can also select the number of input qualification cycles. This is to filter
unwanted noise glitches. The GPIO signals can also be used to bring the device out of specific low-power
modes.
3.2.18
32-Bit CPU-Timers (0, 1, 2)
CPU-Timers 0, 1, and 2 are identical 32-bit timers with presettable periods and with 16-bit clock
prescaling. The timers have a 32-bit count down register, which generates an interrupt when the counter
reaches zero. The counter is decremented at the CPU clock speed divided by the prescale value setting.
When the counter reaches zero, it is automatically reloaded with a 32-bit period value. CPU-Timer 2 is
reserved for Real-Time OS (RTOS)/BIOS applications. CPU-Timer 1 is also reserved for Texas
Instruments system functions. CPU-Timer 2 is connected to INT14 of the CPU. CPU-Timer 1 can be
connected to INT13 of the CPU. CPU-Timer 0 is for general use and is connected to the PIE block.
3.2.19
Control Peripherals
The 280x devices support the following peripherals which are used for embedded control and
communication:
3.2.20
30
ePWM:
The enhanced PWM peripheral supports independent/complementary PWM generation,
adjustable dead-band generation for leading/trailing edges, latched/cycle-by-cycle trip
mechanism. Some of the PWM pins support HRPWM features.
eCAP:
The enhanced capture peripheral uses a 32-bit time base and registers up to four
programmable events in continuous/one-shot capture modes.
This peripheral can also be configured to generate an auxiliary PWM signal.
eQEP:
The enhanced QEP peripheral uses a 32-bit position counter, supports low-speed
measurement using capture unit and high-speed measurement using a 32-bit unit timer.
This peripheral has a watchdog timer to detect motor stall and input error detection logic
to identify simultaneous edge transition in QEP signals.
ADC:
The ADC block is a 12-bit converter, single ended, 16-channels. It contains two
sample-and-hold units for simultaneous sampling.
Serial Port Peripherals
Functional Overview
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
The 280x devices support the following serial communication peripherals:
3.3
eCAN:
This is the enhanced version of the CAN peripheral. It supports 32 mailboxes, time
stamping of messages, and is CAN 2.0B-compliant.
SPI:
The SPI is a high-speed, synchronous serial I/O port that allows a serial bit stream of
programmed length (one to sixteen bits) to be shifted into and out of the device at a
programmable bit-transfer rate. Normally, the SPI is used for communications between the
DSP controller and external peripherals or another processor. Typical applications include
external I/O or peripheral expansion through devices such as shift registers, display
drivers, and ADCs. Multi-device communications are supported by the master/slave
operation of the SPI. On the 280x, the SPI contains a 16-level receive and transmit FIFO
for reducing interrupt servicing overhead.
SCI:
The serial communications interface is a two-wire asynchronous serial port, commonly
known as UART. On the 280x, the SCI contains a 16-level receive and transmit FIFO for
reducing interrupt servicing overhead.
I2C:
The inter-integrated circuit (I2C) module provides an interface between a DSP and other
devices compliant with Philips Semiconductors Inter-IC bus (I2C-bus) specification version
2.1 and connected by way of an I2C-bus. External components attached to this 2-wire
serial bus can transmit/receive up to 8-bit data to/from the DSP through the I2C module.
On the 280x, the I2C contains a 16-level receive and transmit FIFO for reducing interrupt
servicing overhead.
Register Map
The 280x devices contain three peripheral register spaces. The spaces are categorized as follows:
Peripheral
Frame 0:
These are peripherals that are mapped directly to the CPU memory bus.
See Table 3-6
Peripheral
Frame 1
These are peripherals that are mapped to the 32-bit peripheral bus.
See Table 3-7
Peripheral
Frame 2:
These are peripherals that are mapped to the 16-bit peripheral bus.
See Table 3-8
Table 3-6. Peripheral Frame 0 Registers (1) (2)
ADDRESS RANGE
SIZE (x16)
ACCESS TYPE (3)
Device Emulation Registers
0x0880
0x09FF
384
EALLOW protected
FLASH Registers (4)
0x0A80
0x0ADF
96
EALLOW protected
CSM Protected
Code Security Module Registers
0x0AE0
0x0AEF
16
EALLOW protected
0xB00
0xB0F
16
Not EALLOW protected
CPU-TIMER0/1/2 Registers
0x0C00
0x0C3F
64
Not EALLOW protected
PIE Registers
0x0CE0
0x0CFF
32
Not EALLOW protected
PIE Vector Table
0x0D00
0x0DFF
256
EALLOW protected
NAME
ADC Result Registers
(dual-mapped)
(1)
(2)
(3)
(4)
Registers in Frame 0 support 16-bit and 32-bit accesses.
Missing segments of memory space are reserved and should not be used in applications.
If registers are EALLOW protected, then writes cannot be performed until the EALLOW instruction is executed. The EDIS instruction
disables writes to prevent stray code or pointers from corrupting register contents.
The Flash Registers are also protected by the Code Security Module (CSM).
Submit Documentation Feedback
Functional Overview
31
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 3-7. Peripheral Frame 1 Registers (1) (2)
NAME
ADDRESS RANGE
SIZE (x16)
eCANA Registers
0x6000
0x60FF
256
(128 x 32)
Some eCAN control registers (and selected bits in other eCAN
control registers) are EALLOW-protected.
eCANA Mailbox RAM
0x6100
0x61FF
256
(128 x 32)
Not EALLOW-protected
eCANB Registers
0x6200
0x62FF
256
(128 x 32)
Some eCAN control registers (and selected bits in other eCAN
control registers) are EALLOW-protected.
eCANB Mailbox RAM
0x6300
0x63FF
256
(128 x 32)
Not EALLOW-protected
ePWM1 Registers
0x6800
0x683F
64
(32 x 32)
Some ePWM registers are EALLOW protected.
See Table 4-2
ePWM2 Registers
0x6840
0x687F
64
(32 x 32)
Some ePWM registers are EALLOW protected.
See Table 4-2.
ePWM3 Registers
0x6880
0x68BF
64
(32 x 32)
Some ePWM registers are EALLOW protected.
See Table 4-2.
ePWM4 Registers
0x68C0
0x68FF
64
(32 x 32)
Some ePWM registers are EALLOW protected.
See Table 4-2.
ePWM5 Registers
0x6900
0x693F
64
(32 x 32)
Some ePWM registers are EALLOW protected.
See Table 4-2.
ePWM6 Registers
0x6940
0x697F
64
(32 x 32)
Some ePWM registers are EALLOW protected.
See Table 4-2.
eCAP1 Registers
0x6A00
0x6A1F
32
(16 x 32)
Not EALLOW protected
eCAP2 Registers
0x6A20
0x6A3F
32
(16 x 32)
Not EALLOW protected
eCAP3 Registers
0x6A40
0x6A5F
32
(16 x 32)
Not EALLOW protected
eCAP4 Registers
0x6A60
0x6A7F
32
(16 x 32)
Not EALLOW protected
eQEP1 Registers
0x6B00
0x6B3F
64
(32 x 32)
Not EALLOW protected
eQEP2 Registers
0x6B40
0x6B7F
64
(32 x 32)
Not EALLOW protected
GPIO Control Registers
0x6F80
0x6FBF
128
(64 x 32)
EALLOW protected
GPIO Data Registers
0x6FC0
0x6FDF
32
(16 x 32)
Not EALLOW protected
GPIO Interrupt and LPM
Select Registers
0x6FE0
0x6FFF
32
(16 x 32)
EALLOW protected
(1)
(2)
32
ACCESS TYPE
The eCAN control registers only support 32-bit read/write operations. All 32-bit accesses are aligned to even address boundaries.
Missing segments of memory space are reserved and should not be used in applications.
Functional Overview
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 3-8. Peripheral Frame 2 Registers (1) (2)
NAME
ADDRESS RANGE
SIZE (x16)
System Control Registers
0x7010
0x702F
32
EALLOW Protected
SPI-A Registers
0x7040
0x704F
16
Not EALLOW Protected
SCI-A Registers
0x7050
0x705F
16
Not EALLOW Protected
External Interrupt Registers
0x7070
0x707F
16
Not EALLOW Protected
ADC Registers
0x7100
0x711F
32
Not EALLOW Protected
SPI-B Registers
0x7740
0x774F
16
Not EALLOW Protected
SCI-B Registers
0x7750
0x775F
16
Not EALLOW Protected
SPI-C Registers
0x7760
0x776F
16
Not EALLOW Protected
SPI-D Registers
0x7780
0x778F
16
Not EALLOW Protected
I2C Registers
0x7900
0x792F
48
Not EALLOW Protected
(1)
(2)
ACCESS TYPE
Peripheral Frame 2 only allows 16-bit accesses. All 32-bit accesses are ignored (invalid data may be returned or written).
Missing segments of memory space are reserved and should not be used in applications.
3.4
Device Emulation Registers
These registers are used to control the protection mode of the C28x CPU and to monitor some critical
device signals. The registers are defined in Table 3-9.
Table 3-9. Device Emulation Registers
ADDRESS
RANGE
SIZE (x16)
DEVICECNF
0x0880
0x0881
2
Device Configuration Register
PARTID
0x0882
1
Part ID Register
0x002C (1) - F2801/9501
0x0034 - F2806
0x003C - F2808
REVID
0x0883
1
Revision ID Register
0x0000 - Silicon Rev. 0 - TMX
0x0001 - Silicon Rev. A - TMX
0x0002 - Silicon Rev. B - TMS
PROTSTART
0x0884
1
Block Protection Start Address Register
PROTRANGE
0x0885
1
Block Protection Range Address Register
NAME
(1)
DESCRIPTION
The first byte (00) denotes flash devices. "FF" is reserved for future ROM devices. Other values are reserved for future devices.
Submit Documentation Feedback
Functional Overview
33
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
3.5
Interrupts
Figure 3-5 shows how the various interrupt sources are multiplexed within the 280x devices.
Peripherals
(SPI, SCI, I2C, eCAN, ePWM, eCAP, eQEP, ADC)
WDINT
WAKEINT
XINT1
XINT1
Interrupt Control
Low Power Modes
MUX
LPMINT
Watchdog
96 Interrupts
XINT1CTR(15:0)
GPIOXINT1SEL(4:0)
XINT2SOC
ADC
XINT2
C28
MUX
INT1 to
INT12
PIE
XINT1CR(15:0)
XINT2
Interrupt Control
XINT2CR(15:0)
CPU
XINT2CTR(15:0)
GPIOXINT2SEL(4:0)
TINT0
CPU TIMER 0
TINT2
INT14
CPU TIMER 2 (for TI/RTOS)
TINT1
INT13
MUX
CPU TIMER 1 (for TI)
int13_select
nmi_select
GPIO0.int
MUX
NMI
GPIO
MUX
XNMI_XINT13
Interrupt Control
XNMICR(15:0)
MUX
GPIO31.int
1
XNMICTR(15:0)
GPIOXNMISEL(4:0)
Figure 3-5. External and PIE Interrupt Sources
Eight PIE block interrupts are grouped into one CPU interrupt. In total, 12 CPU interrupt groups, with 8
interrupts per group equals 96 possible interrupts. On the 280x, 43 of these are used by peripherals as
shown in Table 3-10.
34
Functional Overview
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
IFR(12:1)
IER(12:1)
INTM
INT1
INT2
1
MUX
INT11
INT12
(Flag)
INTx
Global
Enable
(Enable)
INTx.1
INTx.2
INTx.3
INTx.4
INTx.5
INTx.6
INTx.7
INTx.8
MUX
PIEACKx
(Enable/Flag)
(Enable)
(Flag)
PIEIERx(8:1)
PIEIFRx(8:1)
CPU
0
From
Peripherals or
External
Interrupts
Figure 3-6. Multiplexing of Interrupts Using the PIE Block
Table 3-10. PIE Peripheral Interrupts (1)
CPU
INTERRUPTS
(1)
PIE INTERRUPTS
INTx.8
INTx.7
INTx.6
INTx.5
INTx.4
INTx.3
INTx.2
INTx.1
INT1
WAKEINT
(LPM/WD)
TINT0
(TIMER 0)
ADCINT
(ADC)
XINT2
XINT1
reserved
SEQ2INT
(ADC)
SEQ1INT
(ADC)
INT2
reserved
reserved
INT3
reserved
reserved
EPWM6_INT
(ePWM6)
EPWM5_INT
(ePWM5)
EPWM4_INT
(ePWM4)
EPWM3_INT
(ePWM3)
EPWM2_INT
(ePWM2)
EPWM1_INT
(ePWM1)
INT4
reserved
reserved
reserved
reserved
ECAP4_INT
(eCAP4)
ECAP3_INT
(eCAP3)
ECAP2_INT
(eCAP2)
ECAP1_INT
(eCAP1)
INT5
reserved
reserved
reserved
reserved
reserved
reserved
EQEP2_INT
(eQEP2)
EQEP1_INT
(eQEP1)
INT6
SPITXINTD
(SPI-D)
SPIRXINTD
(SPI-D)
SPITXINTC
(SPI-C)
SPIRXINTC
(SPI-C)
SPITXINTB
(SPI-B)
SPIRXINTB
(SPI-B)
SPITXINTA
(SPI-A)
SPIRXINTA
(SPI-A)
INT7
reserved
reserved
reserved
reserved
reserved
reserved
reserved
reserved
I2CINT1A
(I2C-A)
EPWM6_TZINT EPWM5_TZINT EPWM4_TZINT EPWM3_TZINT EPWM2_TZINT EPWM1_TZINT
(ePWM6)
(ePWM5)
(ePWM4)
(ePWM3)
(ePWM2)
(ePWM1)
INT8
reserved
reserved
reserved
reserved
reserved
reserved
I2CINT2A
(I2C-A)
INT9
ECAN1_INTB
(CAN-B)
ECAN0_INTB
(CAN-B)
ECAN1_INTA
(CAN-A)
ECAN0_INTA
(CAN-A)
SCITXINTB
(SCI-B)
SCIRXINTB
(SCI-B)
SCITXINTA
(SCI-A)
SCIRXINTA
(SCI-A)
INT10
reserved
reserved
reserved
reserved
reserved
reserved
reserved
reserved
INT11
reserved
reserved
reserved
reserved
reserved
reserved
reserved
reserved
INT12
reserved
reserved
reserved
reserved
reserved
reserved
reserved
reserved
Out of the 96 possible interrupts, 43 interrupts are currently used. The remaining interrupts are reserved for future devices. These
interrupts can be used as software interrupts if they are enabled at the PIEIFRx level, provided none of the interrupts within the group is
being used by a peripheral. Otherwise, interrupts coming in from peripherals may be lost by accidentally clearing their flag while
modifying the PIEIFR. To summarize, there are two safe cases when the reserved interrupts could be used as software interrupts:
1) No peripheral within the group is asserting interrupts.
2) No peripheral interrupts are assigned to the group (example PIE group 12).
Submit Documentation Feedback
Functional Overview
35
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 3-11. PIE Configuration and Control Registers
NAME
SIZE (X16)
PIECTRL
0x0CE0
1
PIE, Control Register
PIEACK
0x0CE1
1
PIE, Acknowledge Register
PIEIER1
0x0CE2
1
PIE, INT1 Group Enable Register
PIEIFR1
0x0CE3
1
PIE, INT1 Group Flag Register
PIEIER2
0x0CE4
1
PIE, INT2 Group Enable Register
PIEIFR2
0x0CE5
1
PIE, INT2 Group Flag Register
PIEIER3
0x0CE6
1
PIE, INT3 Group Enable Register
PIEIFR3
0x0CE7
1
PIE, INT3 Group Flag Register
PIEIER4
0x0CE8
1
PIE, INT4 Group Enable Register
PIEIFR4
0x0CE9
1
PIE, INT4 Group Flag Register
PIEIER5
0x0CEA
1
PIE, INT5 Group Enable Register
PIEIFR5
0x0CEB
1
PIE, INT5 Group Flag Register
PIEIER6
0x0CEC
1
PIE, INT6 Group Enable Register
PIEIFR6
0x0CED
1
PIE, INT6 Group Flag Register
PIEIER7
0x0CEE
1
PIE, INT7 Group Enable Register
PIEIFR7
0x0CEF
1
PIE, INT7 Group Flag Register
PIEIER8
0x0CF0
1
PIE, INT8 Group Enable Register
PIEIFR8
0x0CF1
1
PIE, INT8 Group Flag Register
PIEIER9
0x0CF2
1
PIE, INT9 Group Enable Register
PIEIFR9
0x0CF3
1
PIE, INT9 Group Flag Register
PIEIER10
0x0CF4
1
PIE, INT10 Group Enable Register
PIEIFR10
0x0CF5
1
PIE, INT10 Group Flag Register
PIEIER11
0x0CF6
1
PIE, INT11 Group Enable Register
PIEIFR11
0x0CF7
1
PIE, INT11 Group Flag Register
PIEIER12
0x0CF8
1
PIE, INT12 Group Enable Register
PIEIFR12
0x0CF9
1
PIE, INT12 Group Flag Register
Reserved
0x0CFA
0x0CFF
6
Reserved
(1)
3.5.1
DESCRIPTION (1)
ADDRESS
The PIE configuration and control registers are not protected by EALLOW mode. The PIE vector table
is protected.
External Interrupts
Table 3-12. External Interrupt Registers
ADDRESS
SIZE (x16)
XINT1CR
NAME
0x7070
1
XINT1 control register
XINT2CR
0x7071
1
XINT2 control register
reserved
0x7072
0x7076
5
XNMICR
0x7077
1
XNMI control register
XINT1CTR
0x7078
1
XINT1 counter register
XINT2CTR
0x7079
1
XINT2 counter register
reserved
0x707A
0x707E
5
XNMICTR
0x707F
1
36
Functional Overview
DESCRIPTION
XNMI counter register
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Each external interrupt can be enabled/disabled or qualified using positive, negative, or both positive and
negative edge. For more information, see the TMS320x280x System Control and Interrupts Reference
Guide (literature number SPRU712).
3.6
System Control
This section describes the 280x oscillator, PLL and clocking mechanisms, the watchdog function and the
low power modes. Figure 3-7 shows the various clock and reset domains in the 280x devices that will be
discussed.
Reset
XRS
Watchdog
Block
SYSCLKOUT(A)
Peripheral Reset
X1
CLKIN(A)
28x
CPU
PLL
Peripheral
Registers
Peripheral Bus
System
Control
Registers
X2
Power
Modes
Control
CPU
Timers
XCLKIN
Clock Enables
Peripheral
Registers
ePWM 1/2/3/4/5/6
eCAP 1/2/3/4 eQEP 1/2
I/O
Peripheral
Registers
eCAN-A/B
I2C-A
I/O
Low-Speed Prescaler
Peripheral
Registers
OSC
GPIO
MUX
GPIOs
LSPCLK
Low-Speed Peripherals
SCI-A/B, SPI-A/B/C/D
I/O
High-Speed Prescaler
HSPCLK
ADC
Registers
A.
12-Bit ADC
16 ADC inputs
CLKIN is the clock into the CPU. It is passed out of the CPU as SYSCLKOUT (that is, CLKIN is the same frequency
as SYSCLKOUT).
Figure 3-7. Clock and Reset Domains
Submit Documentation Feedback
Functional Overview
37
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
The PLL, clocking, watchdog and low-power modes, are controlled by the registers listed in Table 3-13.
Table 3-13. PLL, Clocking, Watchdog, and Low-Power Mode Registers (1)
ADDRESS
SIZE (x16)
XCLK
NAME
0x7010
1
XCLKOUT Pin Control, X1 and XCLKIN Status Register
PLLSTS
0x7011
1
PLL Status Register
reserved
0x7012
0x7019
8
HISPCP
0x701A
1
High-Speed Peripheral Clock Prescaler Register (for HSPCLK)
LOSPCP
0x701B
1
Low-Speed Peripheral Clock Prescaler Register (for LSPCLK)
PCLKCR0
0x701C
1
Peripheral Clock Control Register 0
PCLKCR1
0x701D
1
Peripheral Clock Control Register 1
LPMCR0
0x701E
1
Low Power Mode Control Register 0
reserved
0x701F
0x7020
1
PLLCR
0x7021
1
PLL Control Register
SCSR
0x7022
1
System Control and Status Register
WDCNTR
0x7023
1
Watchdog Counter Register
reserved
0x7024
1
WDKEY
0x7025
1
reserved
0x7026
0x7028
3
WDCR
0x7029
1
reserved
0x702A
0x702F
6
(1)
DESCRIPTION
Watchdog Reset Key Register
Watchdog Control Register
All of the registers in this table are EALLOW protected.
3.6.1
OSC and PLL Block
Figure 3-8 shows the OSC and PLL block on the 280x.
XCLKIN
(3.3-V clock input)
OSCCLK
OSCCLK
0
xor
PLLSTS[OSCOFF]
PLL
OSCCLK or
VCOCLK
CLKIN
VCOCLK
n
n≠0
/2
PLLSTS[PLLOFF]
PLLSTS[CLKINDIV]
X1
On chip
oscillator
4-bit PLL Select (PLLCR)
X2
Figure 3-8. OSC and PLL Block Diagram
The on-chip oscillator circuit enables a crystal/resonator to be attached to the 280x devices using the X1
and X2 pins. If the on-chip oscillator is not used, an external oscillator can be used in either one of the
following configurations:
1. A 3.3-V external oscillator can be directly connected to the XCLKIN pin. The X2 pin should be left
unconnected and the X1 pin tied low. The logic-high level in this case should not exceed VDDIO.
2. A 1.8-V external oscillator can be directly connected to the X1 pin. The X2 pin should be left
38
Functional Overview
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
unconnected and the XCLKIN pin tied low. The logic-high level in this case should not exceed VDD.
The three possible input-clock configurations are shown in Figure 3-9 through Figure 3-11
XCLKIN
X1
X2
NC
External Clock Signal
(Toggling 0 −VDDIO)
Figure 3-9. Using a 3.3-V External Oscillator
X2
X1
XCLKIN
External Clock Signal
(Toggling 0 −VDD)
NC
Figure 3-10. Using a 1.8-V External Oscillator
XCLKIN
X1
X2
CL2
CL1
Crystal
Figure 3-11. Using the Internal Oscillator
3.6.1.1
External Reference Oscillator Clock Option
The typical specifications for the external quartz crystal for a frequency of 20 MHz are listed below:
• Fundamental mode, parallel resonant
• CL (load capacitance) = 12 pF
• CL1 = CL2 = 24 pF
• Cshunt = 6 pF
• ESR range = 30 to 60 Ω
Texas Instruments recommends that customers have the resonator/crystal vendor characterize the
operation of their device with the DSP chip. The resonator/crystal vendor has the equipment and expertise
to tune the tank circuit. The vendor can also advise the customer regarding the proper tank component
values that will produce proper start up and stability over the entire operating range.
3.6.1.2 PLL-Based Clock Module
The 280x devices have an on-chip, PLL-based clock module. This module provides all the necessary
clocking signals for the device, as well as control for low-power mode entry. The PLL has a 4-bit ratio
control PLLCR[DIV] to select different CPU clock rates. The watchdog module should be disabled before
writing to the PLLCR register. It can be re-enabled (if need be) after the PLL module has stabilized, which
takes 131072 OSCCLK cycles.
Submit Documentation Feedback
Functional Overview
39
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 3-14. PLLCR Register Bit Definitions
(1)
(2)
SYSCLKOUT
(CLKIN) (2)
PLLCR[DIV] (1)
PLLSTS[CLKINDIV]
0000 (PLL bypass)
0
OSCCLK/2
0000 (PLL bypass)
1
OSCCLK
0001
0
(OSCCLK*1)/2
0010
0
(OSCCLK*2)/2
0011
0
(OSCCLK*3)/2
0100
0
(OSCCLK*4)/2
0101
0
(OSCCLK*5)/2
0110
0
(OSCCLK*6)/2
0111
0
(OSCCLK*7)/2
1000
0
(OSCCLK*8)/2
1001
0
(OSCCLK*9)/2
1010
0
(OSCCLK*10)/2
1011-1111
0
reserved
This register is EALLOW protected.
CLKIN is the input clock to the CPU. SYSCLKOUT is the output
clock from the CPU. The frequency of SYSCLKOUT is the same as
CLKIN.
CAUTION
PLLSTS[CLKINDIV] can be set to 1 only if PLLCR is 0x0000. PLLCR should not be
changed once PLLSTS[CLKINDIV] is set.
The PLL-based clock module provides two modes of operation:
• Crystal-operation - This mode allows the use of an external crystal/resonator to provide the time base
to the device.
• External clock source operation - This mode allows the internal oscillator to be bypassed. The device
clocks are generated from an external clock source input on the X1 or the XCLKIN pin.
Table 3-15. Possible PLL Configuration Modes
REMARKS
PLLSTS[CLKINDIV]
SYSCLKOUT
(CLKIN)
Invoked by the user setting the PLLOFF bit in the PLLSTS register. The PLL block
is disabled in this mode. This can be useful to reduce system noise and for low
power operation. The PLLCR register must first be set to 0x0000 (PLL Bypass)
before entering this mode. The CPU clock (CLKIN) is derived directly from the
input clock on either X1/X2, X1 or XCLKIN.
0
OSCCLK/2
1
OSCCLK
0
OSCCLK/2
1
OSCCLK
0
OSCCLK*n/2
PLL MODE
PLL Off
PLL Bypass is the default PLL configuration upon power-up or after an external
reset (XRS). This mode is selected when the PLLCR register is set to 0x0000 or
PLL Bypass
while the PLL locks to a new frequency after the PLLCR register has been
modified. In this mode, the PLL itself is bypassed but the PLL is not turned off.
PLL Enable
Achieved by writing a non-zero value n into the PLLCR register. Upon writing to the
PLLCR the device will switch to PLL Bypass mode until the PLL locks.
3.6.1.3 Loss of Input Clock
In PLL-enabled and PLL-bypass mode, if the input clock OSCCLK is removed or absent, the PLL will still
issue a "limp-mode" clock. The limp-mode clock continues to clock the CPU and peripherals at a typical
frequency of 1-5 MHz. Limp mode is not specified to work from power-up, only after input clocks have
been present initially. In PLL bypass mode, the limp mode clock from the PLL is automatically routed to
the CPU if the input clock is removed or absent.
Normally, when the input clocks are present, the watchdog counter decrements to initiate a watchdog
40
Functional Overview
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
reset or WDINT interrupt. However, when the external input clock fails, the watchdog counter stops
decrementing (i.e., the watchdog counter does not change with the limp-mode clock). In addition to this,
the device will be reset and the “Missing Clock Status” (MCLKSTS) bit will be set. These conditions could
be used by the application firmware to detect the input clock failure and initiate necessary shut-down
procedure for the system.
NOTE
Applications in which the correct CPU operating frequency is absolutely critical should
implement a mechanism by which the DSP will be held in reset, should the input clocks
ever fail. For example, an R-C circuit may be used to trigger the XRS pin of the DSP,
should the capacitor ever get fully charged. An I/O pin may be used to discharge the
capacitor on a periodic basis to prevent it from getting fully charged. Such a circuit would
also help in detecting failure of the flash memory and the VDD3VFL rail.
3.6.2
Watchdog Block
The watchdog block on the 280x is similar to the one used on the 240x and 281x devices. The watchdog
module generates an output pulse, 512 oscillator clocks wide (OSCCLK), whenever the 8-bit watchdog up
counter has reached its maximum value. To prevent this, the user disables the counter or the software
must periodically write a 0x55 + 0xAA sequence into the watchdog key register which will reset the
watchdog counter. Figure 3-12 shows the various functional blocks within the watchdog module.
WDCR (WDPS(2:0))
WDCR (WDDIS)
WDCNTR(7:0)
OSCCLK
Watchdog
Prescaler
/512
WDCLK
8-Bit
Watchdog
Counter
CLR
Clear Counter
Internal
Pullup
WDKEY(7:0)
Watchdog
55 + AA
Key Detector
WDRST
Generate
Output Pulse
WDINT
(512 OSCCLKs)
Good Key
XRS
Core-reset
WDCR (WDCHK(2:0))
WDRST(A)
A.
1
0
Bad
WDCHK
Key
SCSR (WDENINT)
1
The WDRST signal is driven low for 512 OSCCLK cycles.
Figure 3-12. Watchdog Module
The WDINT signal enables the watchdog to be used as a wakeup from IDLE/STANDBY mode.
Submit Documentation Feedback
Functional Overview
41
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
In STANDBY mode, all peripherals are turned off on the device. The only peripheral that remains
functional is the watchdog. The WATCHDOG module will run off OSCCLK. The WDINT signal is fed to the
LPM block so that it can wake the device from STANDBY (if enabled). See Section Section 3.7,
Low-Power Modes Block, for more details.
In IDLE mode, the WDINT signal can generate an interrupt to the CPU, via the PIE, to take the CPU out of
IDLE mode.
In HALT mode, this feature cannot be used because the oscillator (and PLL) are turned off and hence so
is the WATCHDOG.
3.7
Low-Power Modes Block
The low-power modes on the 280x are similar to the 240x devices. Table 3-16 summarizes the various
modes.
Table 3-16. Low-Power Modes
EXIT (1)
MODE
LPMCR0(1:0)
OSCCLK
CLKIN
SYSCLKOUT
IDLE
00
On
On
On (2)
XRS, Watchdog interrupt, any enabled
interrupt, XNMI
STANDBY
01
On
(watchdog still running)
Off
Off
XRS, Watchdog interrupt, GPIO Port A
signal, debugger (3), XNMI
HALT
1X
Off
(oscillator and PLL turned off,
watchdog not functional)
Off
Off
XRS, GPIO Port A signal, XNMI,
debugger (3)
(1)
(2)
(3)
The Exit column lists which signals or under what conditions the low power mode will be exited. A low signal, on any of the signals, will
exit the low power condition. This signal must be kept low long enough for an interrupt to be recognized by the device. Otherwise the
IDLE mode will not be exited and the device will go back into the indicated low power mode.
The IDLE mode on the C28x behaves differently than on the 24x/240x. On the C28x, the clock output from the CPU (SYSCLKOUT) is
still functional while on the 24x/240x the clock is turned off.
On the C28x, the JTAG port can still function even if the CPU clock (CLKIN) is turned off.
The various low-power modes operate as follows:
IDLE Mode:
This mode is exited by any enabled interrupt or an XNMI that is recognized by
the processor. The LPM block performs no tasks during this mode as long as the
LPMCR0(LPM) bits are set to 0,0.
STANDBY Mode:
Any GPIO port A signal (GPIO[31:0]) can wake the device from STANDBY
mode. The user must select which signal(s) will wake the device in the
GPIOLPMSEL register. The selected signal(s) are also qualified by the OSCCLK
before waking the device. The number of OSCCLKs is specified in the LPMCR0
register.
HALT Mode:
Only the XRS and any GPIO port A signal (GPIO[31:0]) can wake the device
from HALT mode. The user selects the signal in the GPIOLPMSEL register.
NOTE
The low-power modes do not affect the state of the output pins (PWM pins included).
They will be in whatever state the code left them in when the IDLE instruction was
executed. See the TMS320x280x System Control and Interrupts Reference Guide
(literature number SPRU712) for more details.
42
Functional Overview
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
4
Peripherals
The integrated peripherals of the 280x are described in the following subsections:
• Three 32-bit CPU-Timers
• Up to six enhanced PWM modules (ePWM1, ePWM2, ePWM3, ePWM4, ePWM5, ePWM6)
• Up to four enhanced capture modules (eCAP1, eCAP2, eCAP3, eCAP4)
• Up to two enhanced QEP modules (eQEP1, eQEP2)
• Enhanced analog-to-digital converter (ADC) module
• Up to two enhanced controller area network (eCAN) modules (eCAN-A, eCAN-B)
• Up to two serial communications interface modules (SCI-A, SCI-B)
• Up to four serial peripheral interface (SPI) modules (SPI-A, SPI-B, SPI-C, SPI-D)
• Inter-integrated circuit module (I2C)
• Digital I/O and shared pin functions
4.1
32-Bit CPU-Timers 0/1/2
There are three 32-bit CPU-timers on the 280x devices (CPU-TIMER0/1/2).
CPU-Timer 1 is reserved for Texas Instruments system functions and Timer 2 is reserved for
DSP/BIOS™. CPU-Timer 0 can be used in user applications. These timers are different from the timers
that are present in the ePWM modules.
NOTE
NOTE: If the application is not using DSP/BIOS, then CPU-Timer 2 can be used in the
application.
Reset
Timer Reload
16-Bit Timer Divide-Down
TDDRH:TDDR
SYSCLKOUT
TCR.4
(Timer Start Status)
32-Bit Timer Period
PRDH:PRD
16-Bit Prescale Counter
PSCH:PSC
Borrow
32-Bit Counter
TIMH:TIM
Borrow
TINT
Figure 4-1. CPU-Timers
In the 280x devices, the timer interrupt signals (TINT0, TINT1, TINT2) are connected as shown in
Figure 4-2.
Submit Documentation Feedback
Peripherals
43
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
INT1
to
INT12
PIE
TINT0
CPU-TIMER 0
C28x
CPU-TIMER 1
(Reserved for TI
system functions)
TINT1
INT13
XINT13
CPU-TIMER 2
(Reserved for
DSP/BIOS)
TINT2
INT14
A.
The timer registers are connected to the memory bus of the C28x processor.
B.
The timing of the timers is synchronized to SYSCLKOUT of the processor clock.
C.
While TIMER1 is reserved, INT13 is not reserved and the user can use XINT13 connected to INT13.
Figure 4-2. CPU-Timer Interrupt Signals and Output Signal
The general operation of the timer is as follows: The 32-bit counter register "TIMH:TIM" is loaded with the
value in the period register "PRDH:PRD". The counter register decrements at the SYSCLKOUT rate of the
C28x. When the counter reaches 0, a timer interrupt output signal generates an interrupt pulse. The
registers listed in Table 4-1 are used to configure the timers. For more information, see the TMS320x280x
System Control and Interrupts Reference Guide (literature number SPRU712).
Table 4-1. CPU-Timers 0, 1, 2 Configuration and Control Registers
ADDRESS
SIZE (x16)
TIMER0TIM
NAME
0x0C00
1
CPU-Timer 0, Counter Register
TIMER0TIMH
0x0C01
1
CPU-Timer 0, Counter Register High
TIMER0PRD
0x0C02
1
CPU-Timer 0, Period Register
TIMER0PRDH
0x0C03
1
CPU-Timer 0, Period Register High
TIMER0TCR
0x0C04
1
CPU-Timer 0, Control Register
reserved
0x0C05
1
TIMER0TPR
0x0C06
1
CPU-Timer 0, Prescale Register
TIMER0TPRH
0x0C07
1
CPU-Timer 0, Prescale Register High
TIMER1TIM
0x0C08
1
CPU-Timer 1, Counter Register
TIMER1TIMH
0x0C09
1
CPU-Timer 1, Counter Register High
TIMER1PRD
0x0C0A
1
CPU-Timer 1, Period Register
TIMER1PRDH
0x0C0B
1
CPU-Timer 1, Period Register High
TIMER1TCR
0x0C0C
1
CPU-Timer 1, Control Register
reserved
0x0C0D
1
TIMER1TPR
0x0C0E
1
CPU-Timer 1, Prescale Register
TIMER1TPRH
0x0C0F
1
CPU-Timer 1, Prescale Register High
TIMER2TIM
0x0C10
1
CPU-Timer 2, Counter Register
TIMER2TIMH
0x0C11
1
CPU-Timer 2, Counter Register High
TIMER2PRD
0x0C12
1
CPU-Timer 2, Period Register
TIMER2PRDH
0x0C13
1
CPU-Timer 2, Period Register High
TIMER2TCR
0x0C14
1
CPU-Timer 2, Control Register
reserved
0x0C15
1
44
Peripherals
DESCRIPTION
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 4-1. CPU-Timers 0, 1, 2 Configuration and Control Registers (continued)
ADDRESS
SIZE (x16)
TIMER2TPR
NAME
0x0C16
1
CPU-Timer 2, Prescale Register
TIMER2TPRH
0x0C17
1
CPU-Timer 2, Prescale Register High
reserved
0x0C18
0x0C3F
40
4.2
DESCRIPTION
Enhanced PWM Modules (ePWM1/2/3/4/5/6)
The 280x device contains up to six enhanced PWM Modules (ePWM). Figure 4-3 shows a block diagram
of multiple ePWM modules. Figure 4-4 shows the signal interconnections with the ePWM. See the
TMS320x280x Enhanced Pulse Width Modulator (ePWM) Module Reference Guide (literature number
SPRU791) for more details.
EPWM1SYNCI
EPWM1INT
EPWM1SYNCI
EPWM1A
EPWM1SOC
ePWM1 module
EPWM1B
TZ1 to TZ6
to eCAP1
module
(sync in)
EPWM1SYNCO
EPWM1SYNCO
.
EPWM2SYNCI
EPWM2INT
EPWM2SOC
PIE
EPWM2A
ePWM2 module
EPWM2B
GPIO
MUX
TZ1 to TZ6
EPWM2SYNCO
EPWMxSYNCI
EPWMxINT
EPWMxSOC
EPWMxA
ePWMx module
EPWMxB
EPWMxSYNCO
TZ1 to TZ6
ADCSOCx0
ADC
Peripheral Bus
Figure 4-3. Multiple PWM Modules in a 280x System
Table 4-2 shows the complete ePWM register set per module.
Submit Documentation Feedback
Peripherals
45
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 4-2. ePWM Control and Status Registers
NAME
EPWM1
EPWM2
EPWM3
EPWM4
EPWM5
EPWM6
SIZE (x16) /
#SHADOW
TBCTL
0x6800
0x6840
0x6880
0x68C0
0x6900
0x6940
1/0
Time Base Control Register
TBSTS
0x6801
0x6841
0x6881
0x68C1
0x6901
0x6941
1/0
Time Base Status Register
TBPHSHR
0x6802
0x6842
0x6882
0x68C2
N/A
N/A
1/0
Time Base Phase HRPWM Register
TBPHS
0x6803
0x6843
0x6883
0x68C3
0x6903
0x6943
1/0
Time Base Phase Register
TBCNT
0x6804
0x6844
0x6884
0x68C4
0x6904
0x6944
1/0
Time Base Counter Register
TBPRD
0x6805
0x6845
0x6885
0x68C5
0x6905
0x6945
1/1
Time Base Period Register Set
CMPCTL
0x6807
0x6847
0x6887
0x68C7
0x6907
0x6947
1/0
Counter Compare Control Register
CMPAHR
0x6808
0x6848
0x6888
0x68C8
N/A
N/A
1/1
Time Base Compare A HRPWM Register
CMPA
0x6809
0x6849
0x6889
0x68C9
0x6909
0x6949
1/1
Counter Compare A Register Set
CMPB
0x680A
0x684A
0x688A
0x68CA
0x690A
0x694A
1/1
Counter Compare B Register Set
AQCTLA
0x680B
0x684B
0x688B
0x68CB
0x690B
0x694B
1/0
Action Qualifier Control Register For Output A
AQCTLB
0x680C
0x684C
0x688C
0x68CC
0x690C
0x694C
1/0
Action Qualifier Control Register For Output B
AQSFRC
0x680D
0x684D
0x688D
0x68CD
0x690D
0x694D
1/0
Action Qualifier Software Force Register
AQCSFRC
0x680E
0x684E
0x688E
0x68CE
0x690E
0x694E
1/1
Action Qualifier Continuous S/W Force Register Set
DBCTL
0x680F
0x684F
0x688F
0x68CF
0x690F
0x694F
1/1
Dead-Band Generator Control Register
DBRED
0x6810
0x6850
0x6890
0x68D0
0x6910
0x6950
1/0
Dead-Band Generator Rising Edge Delay Count Register
DBFED
0x6811
0x6851
0x6891
0x68D1
0x6911
0x6951
1/0
Dead-Band Generator Falling Edge Delay Count Register
TZSEL
0x6812
0x6852
0x6892
0x68D2
0x6912
0x6952
1/0
Trip Zone Select Register (1)
TZCTL
0x6814
0x6854
0x6894
0x68D4
0x6914
0x6954
1/0
Trip Zone Control Register (1)
TZEINT
0x6815
0x6855
0x6895
0x68D5
0x6915
0x6955
1/0
Trip Zone Enable Interrupt Register (1)
TZFLG
0x6816
0x6856
0x6896
0x68D6
0x6916
0x6956
1/0
Trip Zone Flag Register
TZCLR
0x6817
0x6857
0x6897
0x68D7
0x6917
0x6957
1/0
Trip Zone Clear Register (1)
TZFRC
0x6818
0x6858
0x6898
0x68D8
0x6918
0x6958
1/0
Trip Zone Force Register (1)
ETSEL
0x6819
0x6859
0x6899
0x68D9
0x6919
0x6959
1/0
Event Trigger Selection Register
ETPS
0x681A
0x685A
0x689A
0x68DA
0x691A
0x695A
1/0
Event Trigger Prescale Register
ETFLG
0x681B
0x685B
0x689B
0x68DB
0x691B
0x695B
1/0
Event Trigger Flag Register
ETCLR
0x681C
0x685C
0x689C
0x68DC
0x691C
0x695C
1/0
Event Trigger Clear Register
ETFRC
0x681D
0x685D
0x689D
0x68DD
0x691D
0x695D
1/0
Event Trigger Force Register
PCCTL
0x681E
0x685E
0x689E
0x68DE
0x691E
0x695E
1/0
PWM Chopper Control Register
HRCNFG
0x6820
0x6860
0x68A0
0x68E0
N/A
N/A
1/0
HRPWM Configuration Register
(1)
46
DESCRIPTION
Registers that are EALLOW protected.
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Time−base (TB)
Sync
in/out
select
Mux
CTR=ZERO
CTR=CMPB
Disabled
TBPRD shadow (16)
TBPRD active (16)
CTR=PRD
EPWMxSYNCO
TBCTL[SYNCOSEL]
TBCTL[CNTLDE]
EPWMxSYNCI
Counter
up/down
(16 bit)
CTR=ZERO
CTR_Dir
TBCNT
active (16)
TBPHSHR (8)
16
8
TBPHS active (24)
Phase
control
Counter compare (CC)
CTR=CMPA
CMPAHR (8)
16
TBCTL[SWFSYNC]
(software forced sync)
Action
qualifier
(AQ)
CTR = PRD
CTR = ZERO
CTR = CMPA
CTR = CMPB
CTR_Dir
8
Event
trigger
and
interrupt
(ET)
EPWMxINT
EPWMxSOCA
EPWMxSOCB
HiRes PWM (HRPWM)
CMPA active (24)
EPWMA
EPWMxAO
CMPA shadow (24)
CTR=CMPB
Dead
band
(DB)
16
PWM
chopper
(PC)
EPWMB
EPWMxBO
CMPB active (16)
CMPB shadow (16)
Trip
zone
(TZ)
EPWMxTZINT
CTR = ZERO
TZ1 to TZ6
Figure 4-4. ePWM Sub-modules Showing Critical Internal Signal Interconects
4.3
Hi-Resolution PWM (HRPWM)
The HRPWM module offers PWM resolution (time granularity) which is significantly better than what can
be achieved using conventionally derived digital PWM methods. The key points for the HRPWM module
are:
• Significantly extends the time resolution capabilities of conventionally derived digital PWM
• Typically used when effective PWM resolution falls below ~ 9-10 bits. This occurs at PWM frequencies
greater than ~200 KHz when using a CPU/System clock of 100 MHz.
• This capability can be utilized in both duty cycle and phase-shift control methods.
• Finer time granularity control or edge positioning is controlled via extensions to the Compare A and
Phase registers of the ePWM module.
• HRPWM capabilities are offered only on the A signal path of an ePWM module (i.e., on the EPWMxA
output). EPWMxB output has conventional PWM capabilities.
Only PWM channels ePWM 1A, 2A, 3A, 4A support HRPWM features. The remaining ePWM
channels do not support the HRPWM features.
Submit Documentation Feedback
Peripherals
47
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
4.4
Enhanced CAP Modules (eCAP1/2/3/4)
The 280x device contains up to four enhanced capture (eCAP) modules. Figure 4-5 shows a functional
block diagram of a module. See the TMS320x280x Enhanced Capture (eCAP) Module Reference Guide
(literature number SPRU807) for more details.
The eCAP modules are clocked at the SYSCLKOUT rate.
SYNC
The clock enable bits (ECAP1/2/3/4ENCLK) in the PCLKCR1 register are used to turn off the eCAP
modules individually (for low power operation). Upon reset, ECAP1ENCLK, ECAP2ENCLK,
ECAP3ENCLK, and ECAP4ENCLK are set to low, indicating that the peripheral clock is off.
SYNCIn
SYNCOut
CTRPHS
(phase register−32 bit)
TSCTR
(counter−32 bit)
APWM mode
OVF
RST
CTR_OVF
Delta−mode
CTR [0−31]
PRD [0−31]
PWM
compare
logic
CMP [0−31]
32
CTR=PRD
CTR [0−31]
CTR=CMP
32
32
LD1
CAP1
(APRD active)
APRD
shadow
32
32
MODE SELECT
PRD [0−31]
Polarity
select
LD
32
CMP [0−31]
CAP2
(ACMP active)
32
LD
LD2
Polarity
select
Event
qualifier
ACMP
shadow
32
CAP3
(APRD shadow)
LD
32
CAP4
(ACMP shadow)
LD
eCAPx
Event
Pre-scale
Polarity
select
LD3
LD4
Polarity
select
4
Capture events
4
CEVT[1:4]
to PIE
Interrupt
Trigger
and
Flag
control
CTR_OVF
Continuous /
Oneshot
Capture Control
CTR=PRD
CTR=CMP
Figure 4-5. eCAP Functional Block Diagram
48
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 4-3. eCAP Control and Status Registers
NAME
ECAP1
ECAP2
ECAP3
ECAP4
SIZE
(x16)
DESCRIPTION
TSCTR
0x6A00
0x6A20
0x6A40
0x6A60
2
Time-Stamp Counter
CTRPHS
0x6A02
0x6A22
0x6A42
0x6A62
2
Counter Phase Offset Value Register
CAP1
0x6A04
0x6A24
0x6A44
0x6A64
2
Capture 1 Register
CAP2
0x6A06
0x6A26
0x6A46
0x6A66
2
Capture 2 Register
CAP3
0x6A08
0x6A28
0x6A48
0x6A68
2
Capture 3 Register
Capture 4 Register
CAP4
0x6A0A
0x6A2A
0x6A4A
0x6A6A
2
Reserved
0x6A0C0x6A12
0x6A2C0x6A32
0x6A4C0x6A52
0x6A6C0x6A72
8
ECCTL1
0x6A14
0x6A34
0x6A54
0x6A74
1
Capture Control Register 1
ECCTL2
0x6A15
0x6A35
0x6A55
0x6A75
1
Capture Control Register 2
ECEINT
0x6A16
0x6A36
0x6A56
0x6A76
1
Capture Interrupt Enable Register
ECFLG
0x6A17
0x6A37
0x6A57
0x6A77
1
Capture Interrupt Flag Register
ECCLR
0x6A18
0x6A38
0x6A58
0x6A78
1
Capture Interrupt Clear Register
ECFRC
0x6A19
0x6A39
0x6A59
0x6A79
1
Capture Interrupt Force Register
Reserved
0x6A1A0x6A1F
0x6A3A0x6A3F
0x6A5A0x6A5F
0x6A7A0x6A7F
6
4.5
Enhanced QEP Modules (eQEP1/2)
The 280x device contains up to two enhanced quadrature encoder (eQEP) modules. See the
TMS320x280x Enhanced Quadrature Encoder (eQEP) Module Reference Guide (literature number
SPRU790) for more details.
Submit Documentation Feedback
Peripherals
49
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
System
control registers
To CPU
EQEPxENCLK
Data bus
SYSCLKOUT
QCPRD
QCTMR
QCAPCTL
16
16
16
Quadrature
capture unit
(QCAP)
QCTMRLAT
QCPRDLAT
Registers
used by
multiple units
QUTMR
QWDTMR
QUPRD
QWDPRD
32
16
QEPCTL
QEPSTS
UTIME
QFLG
UTOUT
QWDOG
QDECCTL
16
WDTOUT
PIE
EQEPxAIN
QCLK
EQEPxINT
16
QI
Position counter/
control unit
(PCCU)
QPOSLAT
QS
PHE
QPOSSLAT
EQEPxIIN
Quadrature
decoder
(QDU)
PCSOUT
QPOSILAT
EQEPxIOUT
EQEPxIOE
EQEPxSIN
EQEPxSOUT
EQEPxSOE
32
32
QPOSCNT
QPOSINIT
QPOSMAX
QPOSCMP
EQEPxA/XCLK
EQEPxBIN
QDIR
EQEPxB/XDIR
GPIO
MUX
EQEPxI
EQEPxS
16
QEINT
QFRC
QCLR
QPOSCTL
Enhanced QEP (eQEP) peripheral
Figure 4-6. eQEP Functional Block Diagram
50
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 4-4. eQEP Control and Status Registers
NAME
EQEP1
ADDRESS
EQEP2
ADDRESS
EQEP1
SIZE(x16)/
#SHADOW
REGISTER DESCRIPTION
QPOSCNT
0x6B00
0x6B40
2/0
eQEP Position Counter
QPOSINIT
0x6B02
0x6B42
2/0
eQEP Initialization Position Count
QPOSMAX
0x6B04
0x6B44
2/0
eQEP Maximum Position Count
QPOSCMP
0x6B06
0x6B46
2/1
eQEP Position-compare
QPOSILAT
0x6B08
0x6B48
2/0
eQEP Index Position Latch
QPOSSLAT
0x6B0A
0x6B4A
2/0
eQEP Strobe Position Latch
QPOSLAT
0x6B0C
0x6B4C
2/0
eQEP Position Latch
QUTMR
0x6B0E
0x6B4E
2/0
eQEP Unit Timer
QUPRD
0x6B10
0x6B50
2/0
eQEP Unit Period Register
QWDTMR
0x6B12
0x6B52
1/0
eQEP Watchdog Timer
QWDPRD
0x6B13
0x6B53
1/0
eQEP Watchdog Period Register
QDECCTL
0x6B14
0x6B54
1/0
eQEP Decoder Control Register
QEPCTL
0x6B15
0x6B55
1/0
eQEP Control Register
QCAPCTL
0x6B16
0x6B56
1/0
eQEP Capture Control Register
QPOSCTL
0x6B17
0x6B57
1/0
eQEP Position-compare Control Register
QEINT
0x6B18
0x6B58
1/0
eQEP Interrupt Enable Register
QFLG
0x6B19
0x6B59
1/0
eQEP Interrupt Flag Register
QCLR
0x6B1A
0x6B5A
1/0
eQEP Interrupt Clear Register
QFRC
0x6B1B
0x6B5B
1/0
eQEP Interrupt Force Register
QEPSTS
0x6B1C
0x6B5C
1/0
eQEP Status Register
QCTMR
0x6B1D
0x6B5D
1/0
eQEP Capture Timer
QCPRD
0x6B1E
0x6B5E
1/0
eQEP Capture Period Register
QCTMRLAT
0x6B1F
0x6B5F
1/0
eQEP Capture Timer Latch
QCPRDLAT
0x6B20
0x6B60
1/0
eQEP Capture Period Latch
Reserved
0x6B210x6B3F
0x6B610x6B7F
31/0
Submit Documentation Feedback
Peripherals
51
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
4.6
Enhanced Analog-to-Digital Converter (ADC) Module
A simplified functional block diagram of the ADC module is shown in Figure 4-7. The ADC module
consists of a 12-bit ADC with a built-in sample-and-hold (S/H) circuit. Functions of the ADC module
include:
• 12-bit ADC core with built-in S/H
• Analog input: 0 V to 3 V (Voltages above 3 V produce full-scale conversion results.)
• Fast conversion rate: 160 ns at 12.5-MHz ADC clock, 6.25 MSPS
• 16-channel, MUXed inputs
• Autosequencing capability provides up to 16 "autoconversions" in a single session. Each conversion
can be programmed to select any 1 of 16 input channels
• Sequencer can be operated as two independent 8-state sequencers or as one large 16-state
sequencer (i.e., two cascaded 8-state sequencers)
• Sixteen result registers (individually addressable) to store conversion values
– The digital value of the input analog voltage is derived by:
when input ≤ 0 V
Digital Value + 0,
Digital Value + 4096
Digital Value + 4095,
A.
•
•
•
•
•
Input Analog Voltage * ADCLO
3
when 0 V < input < 3 V
when input ≥ 3 V
All fractional values are truncated.
Multiple triggers as sources for the start-of-conversion (SOC) sequence
– S/W - software immediate start
– ePWM start of conversion
– XINT2 ADC start of conversion
Flexible interrupt control allows interrupt request on every end-of-sequence (EOS) or every other EOS.
Sequencer can operate in "start/stop" mode, allowing multiple "time-sequenced triggers" to
synchronize conversions.
SOCA and SOCB triggers can operate independently in dual-sequencer mode.
Sample-and-hold (S/H) acquisition time window has separate prescale control.
The ADC module in the 280x has been enhanced to provide flexible interface to ePWM peripherals. The
ADC interface is built around a fast, 12-bit ADC module with a fast conversion rate of 160 ns at 12.5-MHz
ADC clock. The ADC module has 16 channels, configurable as two independent 8-channel modules. The
two independent 8-channel modules can be cascaded to form a 16-channel module. Although there are
multiple input channels and two sequencers, there is only one converter in the ADC module. Figure 4-7
shows the block diagram of the ADC module.
The two 8-channel modules have the capability to autosequence a series of conversions, each module
has the choice of selecting any one of the respective eight channels available through an analog MUX. In
the cascaded mode, the autosequencer functions as a single 16-channel sequencer. On each sequencer,
once the conversion is complete, the selected channel value is stored in its respective RESULT register.
Autosequencing allows the system to convert the same channel multiple times, allowing the user to
perform oversampling algorithms. This gives increased resolution over traditional single-sampled
conversion results.
52
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
System
Control Block
ADCENCLK
SYSCLKOUT
High-Speed
Prescaler
HALT
DSP
HSPCLK
Analog
MUX
Result Registers
Result Reg 0
ADCINA0
70A8h
Result Reg 1
S/H
ADCINA7
12-Bit
ADC
Module
Result Reg 7
70AFh
Result Reg 8
70B0h
Result Reg 15
70B7h
ADCINB0
S/H
ADCINB7
ADC Control Registers
S/W
EPWMSOCA
GPIO/XINT2
_ADCSOC
SOC
Sequencer 2
Sequencer 1
S/W
SOC
EPWMSOCB
Figure 4-7. Block Diagram of the ADC Module
To obtain the specified accuracy of the ADC, proper board layout is very critical. To the best extent
possible, traces leading to the ADCIN pins should not run in close proximity to the digital signal paths.
This is to minimize switching noise on the digital lines from getting coupled to the ADC inputs.
Furthermore, proper isolation techniques must be used to isolate the ADC module power pins ( VDD1A18,
VDD2A18 , VDDA2, VDDAIO ) from the digital supply.Figure 4-8 shows the ADC pin connections for the 280x
devices.
NOTE
1. The ADC registers are accessed at the SYSCLKOUT rate. The internal timing of the
ADC module is controlled by the high-speed peripheral clock (HSPCLK).
2. The behavior of the ADC module based on the state of the ADCENCLK and HALT
signals is as follows:
–
–
ADCENCLK: On reset, this signal will be low. While reset is active-low (XRS) the
clock to the register will still function. This is necessary to make sure all registers
and modes go into their default reset state. The analog module, however, will be
in a low-power inactive state. As soon as reset goes high, then the clock to the
registers will be disabled. When the user sets the ADCENCLK signal high, then
the clocks to the registers will be enabled and the analog module will be enabled.
There will be a certain time delay (ms range) before the ADC is stable and can be
used.
HALT: This mode only affects the analog module. It does not affect the registers.
In this mode, the ADC module goes into low-power mode. This mode also will stop
the clock to the CPU, which will stop the HSPCLK; therefore, the ADC register
logic will be turned off indirectly.
Submit Documentation Feedback
Peripherals
53
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Figure 4-8 shows the ADC pin-biasing for internal reference and Figure 4-9 shows the ADC pin-biasing for
external reference.
ADC 16-Channel Analog Inputs
ADCINA[7:0]
ADCINB[7:0]
ADCLO
ADCREFIN
Analog input 0−3 V with respect to ADCLO
Connect to analog ground
Float or ground if internal reference is used
22 kW
ADC External Current Bias Resistor
ADCRESEXT
ADC Reference Positive Output
ADCREFP
ADC Reference Medium Output
ADCREFM
ADC Power
2.2 mF (A)
2.2 mF (A)
VDD1A18
VDD2A18
ADCREFP and ADCREFM should not
be loaded by external circuitry
VSS1AGND
VSS2AGND
ADC Analog Power Pin (1.8 V)
ADC Analog Power Pin (1.8 V)
ADC Analog Ground Pin
ADC Analog Ground Pin
VDDA2
VSSA2
ADC Analog Power Pin (3.3 V)
ADC Analog Ground Pin
VDDAIO
VSSAIO
ADC Analog Power Pin (3.3 V)
ADC Analog I/O Ground Pin
ADC Analog and Reference I/O Power
A.
TAIYO YUDEN LMK212BJ225MG-T or equivalent
B.
External decoupling capacitors are recommended on all power pins.
C.
Analog inputs must be driven from an operational amplifier that does not degrade the ADC performance.
Figure 4-8. ADC Pin Connections With Internal Reference
54
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
ADC 16-Channel Analog Inputs
ADCINA[7:0]
ADCINB[7:0]
ADCLO
ADCREFIN
Analog input 0−3 V with respect to ADCLO
Connect to Analog Ground
Connect to 1.500, 1.024, or 2.048-V precision source (D)
22 kW
ADC External Current Bias Resistor
ADCRESEXT
ADC Reference Positive Output
ADCREFP
ADC Reference Medium Output
ADCREFM
ADC Analog Power
VDD1A18
VDD2A18
VSS1AGND
VSS2AGND
ADC Analog Power Pin (1.8 V)
ADC Analog Power Pin (1.8 V)
ADC Analog Ground Pin
ADC Analog Ground Pin
VDDA2
VSSA2
ADC Analog Power Pin (3.3 V)
ADC Analog Ground Pin
VDDAIO
VSSAIO
ADC Analog Power Pin (3.3 V)
ADC Analog and Reference I/O Power
2.2 mF (A)
2.2 mF (A)
ADCREFP and ADCREFM should not
be loaded by external circuitry
ADC Analog I/O Ground Pin
A.
TAIYO YUDEN LMK212BJ225MG-T or equivalent
B.
External decoupling capacitors are recommended on all power pins.
C.
Analog inputs must be driven from an operational amplifier that does not degrade the ADC performance.
D.
External voltage on ADCREFIN is enabled by changing bits 15:14 in the ADC Reference Select register depending on
the voltage used on this pin. Texas Instruments recommends Texas Instruments part REF3020 or equivalent for
2.048-V generation. Overall gain accuracy will be determined by accuracy of this voltage source.
Figure 4-9. ADC Pin Connections With External Reference
NOTE
The temperature rating of any recommended component must match the rating of the end
product.
The ADC operation is configured, controlled, and monitored by the registers listed in Table 4-5.
Submit Documentation Feedback
Peripherals
55
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 4-5. ADC Registers (1)
NAME
ADDRESS (1)
ADDRESS (2)
ADCTRL1
0x7100
1
ADC Control Register 1
SIZE (x16)
DESCRIPTION
ADCTRL2
0x7101
1
ADC Control Register 2
ADCMAXCONV
0x7102
1
ADC Maximum Conversion Channels Register
ADCCHSELSEQ1
0x7103
1
ADC Channel Select Sequencing Control Register 1
ADCCHSELSEQ2
0x7104
1
ADC Channel Select Sequencing Control Register 2
ADCCHSELSEQ3
0x7105
1
ADC Channel Select Sequencing Control Register 3
ADCCHSELSEQ4
0x7106
1
ADC Channel Select Sequencing Control Register 4
ADCASEQSR
0x7107
1
ADC Auto-Sequence Status Register
ADCRESULT0
0x7108
0x0B00
1
ADC Conversion Result Buffer Register 0
ADCRESULT1
0x7109
0x0B01
1
ADC Conversion Result Buffer Register 1
ADCRESULT2
0x710A
0x0B02
1
ADC Conversion Result Buffer Register 2
ADCRESULT3
0x710B
0x0B03
1
ADC Conversion Result Buffer Register 3
ADCRESULT4
0x710C
0x0B04
1
ADC Conversion Result Buffer Register 4
ADCRESULT5
0x710D
0x0B05
1
ADC Conversion Result Buffer Register 5
ADCRESULT6
0x710E
0x0B06
1
ADC Conversion Result Buffer Register 6
ADCRESULT7
0x710F
0x0B07
1
ADC Conversion Result Buffer Register 7
ADCRESULT8
0x7110
0x0B08
1
ADC Conversion Result Buffer Register 8
ADCRESULT9
0x7111
0x0B09
1
ADC Conversion Result Buffer Register 9
ADCRESULT10
0x7112
0x0B0A
1
ADC Conversion Result Buffer Register 10
ADCRESULT11
0x7113
0x0B0B
1
ADC Conversion Result Buffer Register 11
ADCRESULT12
0x7114
0x0B0C
1
ADC Conversion Result Buffer Register 12
ADCRESULT13
0x7115
0x0B0D
1
ADC Conversion Result Buffer Register 13
ADCRESULT14
0x7116
0x0B0E
1
ADC Conversion Result Buffer Register 14
ADCRESULT15
0x7117
0x0B0F
1
ADC Conversion Result Buffer Register 15
ADCTRL3
0x7118
1
ADC Control Register 3
ADCST
0x7119
1
ADC Status Register
Reserved
0x711A
0x711B
2
(1)
(2)
56
ADCREFSEL
0x711C
1
ADC Reference Select Register
ADCOFFTRIM
0x711D
1
ADC Offset Trim Register
Reserved
0x711E
0x711F
2
ADC Status Register
The registers in this column are Peripheral Frame 2 Registers.
The ADC result registers are dual mapped in the 280x DSP. Locations in Peripheral Frame 2 (0x7108-0x7117) are 2 wait states and left
justified. Locations in Peripheral frame 0 space (0x0B00-0x0B0F) are 0 wait sates and right justified. During high speed/continuous
conversion use of the ADC, use the 0 wait state locations for fast transfer of ADC results to user memory.
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
4.7
Enhanced Controller Area Network (eCAN) Modules (eCAN-A and eCAN-B)
The CAN module has the following features:
• Fully compliant with CAN protocol, version 2.0B
• Supports data rates up to 1 Mbps
• Thirty-two mailboxes, each with the following properties:
– Configurable as receive or transmit
– Configurable with standard or extended identifier
– Has a programmable receive mask
– Supports data and remote frame
– Composed of 0 to 8 bytes of data
– Uses a 32-bit time stamp on receive and transmit message
– Protects against reception of new message
– Holds the dynamically programmable priority of transmit message
– Employs a programmable interrupt scheme with two interrupt levels
– Employs a programmable alarm on transmission or reception time-out
• Low-power mode
• Programmable wake-up on bus activity
• Automatic reply to a remote request message
• Automatic retransmission of a frame in case of loss of arbitration or error
• 32-bit local network time counter synchronized by a specific message (communication in conjunction
with mailbox 16)
• Self-test mode
– Operates in a loopback mode receiving its own message. A "dummy" acknowledge is provided,
thereby eliminating the need for another node to provide the acknowledge bit.
NOTE
For a SYSCLKOUT of 100 MHz, the smallest bit rate possible is 15.6 kbps.
Submit Documentation Feedback
Peripherals
57
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
eCAN0INT
Controls Address
eCAN1INT
Data
Enhanced CAN Controller
32
Message Controller
Mailbox RAM
(512 Bytes)
32-Message Mailbox
of 4 × 32-Bit Words
Memory Management
Unit
32
CPU Interface,
Receive Control Unit,
Timer Management Unit
eCAN Memory
(512 Bytes)
Registers and Message
Objects Control
32
32
Receive Buffer
eCAN Protocol Kernel
Transmit Buffer
Control Buffer
Status Buffer
SN65HVD23x
3.3-V CAN Transceiver
CAN Bus
Figure 4-10. eCAN Block Diagram and Interface Circuit
Table 4-6. 3.3-V eCAN Transceivers
58
PART NUMBER
SUPPLY
VOLTAGE
LOW-POWER MODE
SLOPE
CONTROL
VREF
OTHER
TA
SN65HVD230
3.3 V
Standby
Adjustable
Yes
–
-40°C to 85°C
SN65HVD230Q
3.3 V
Standby
Adjustable
Yes
–
-40°C to 125°C
SN65HVD231
3.3 V
Sleep
Adjustable
Yes
–
-40°C to 85°C
SN65HVD231Q
3.3 V
Sleep
Adjustable
Yes
–
-40°C to 125°C
SN65HVD232
3.3 V
None
None
None
–
-40°C to 85°C
SN65HVD232Q
3.3 V
None
None
None
–
-40°C to 125°C
SN65HVD233
3.3 V
Standby
Adjustable
None
Diagnostic
Loopback
-40°C to 125°C
SN65HVD234
3.3 V
Standby & Sleep
Adjustable
None
–
-40°C to 125°C
SN65HVD235
3.3 V
Standby
Adjustable
None
Autobaud
Loopback
-40°C to 125°C
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
eCAN-A Control and Status Registers
Mailbox Enable − CANME
Mailbox Direction − CANMD
Transmission Request Set − CANTRS
Transmission Request Reset − CANTRR
Transmission Acknowledge − CANTA
eCAN-A Memory (512 Bytes)
6000h
Abort Acknowledge − CANAA
Received Message Pending − CANRMP
Control and Status Registers
Received Message Lost − CANRML
603Fh
6040h
607Fh
6080h
60BFh
60C0h
60FFh
Remote Frame Pending − CANRFP
Local Acceptance Masks (LAM)
(32 × 32-Bit RAM)
Global Acceptance Mask − CANGAM
Message Object Time Stamps (MOTS)
(32 × 32-Bit RAM)
Bit-Timing Configuration − CANBTC
Message Object Time-Out (MOTO)
(32 × 32-Bit RAM)
Transmit Error Counter − CANTEC
Master Control − CANMC
Error and Status − CANES
Receive Error Counter − CANREC
Global Interrupt Flag 0 − CANGIF0
Global Interrupt Mask − CANGIM
Global Interrupt Flag 1 − CANGIF1
eCAN-A Memory RAM (512 Bytes)
6100h−6107h
Mailbox 0
6108h−610Fh
Mailbox 1
6110h−6117h
Mailbox 2
6118h−611Fh
Mailbox 3
6120h−6127h
Mailbox 4
Mailbox Interrupt Mask − CANMIM
Mailbox Interrupt Level − CANMIL
Overwrite Protection Control − CANOPC
TX I/O Control − CANTIOC
RX I/O Control − CANRIOC
Time Stamp Counter − CANTSC
Time-Out Control − CANTOC
Time-Out Status − CANTOS
61E0h−61E7h
Mailbox 28
61E8h−61EFh
Mailbox 29
61F0h−61F7h
Mailbox 30
61F8h−61FFh
Mailbox 31
Reserved
Message Mailbox (16 Bytes)
61E8h−61E9h
Message Identifier − MSGID
61EAh−61EBh
Message Control − MSGCTRL
61ECh−61EDh
Message Data Low − MDL
61EEh−61EFh
Message Data High − MDH
Figure 4-11. eCAN-A Memory Map
Submit Documentation Feedback
Peripherals
59
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
eCAN-B Control and Status Registers
Mailbox Enable − CANME
Mailbox Direction − CANMD
Transmission Request Set − CANTRS
Transmission Request Reset − CANTRR
Transmission Acknowledge − CANTA
eCAN-B Memory (512 Bytes)
6200h
Abort Acknowledge − CANAA
Received Message Pending − CANRMP
Control and Status Registers
Received Message Lost − CANRML
623Fh
6240h
627Fh
6280h
62BFh
62C0h
62FFh
Remote Frame Pending − CANRFP
Local Acceptance Masks (LAM)
(32 × 32-Bit RAM)
Global Acceptance Mask − CANGAM
Message Object Time Stamps (MOTS)
(32 × 32-Bit RAM)
Bit-Timing Configuration − CANBTC
Message Object Time-Out (MOTO)
(32 × 32-Bit RAM)
Transmit Error Counter − CANTEC
Master Control − CANMC
Error and Status − CANES
Receive Error Counter − CANREC
Global Interrupt Flag 0 − CANGIF0
Global Interrupt Mask − CANGIM
Global Interrupt Flag 1 − CANGIF1
eCAN-B Memory RAM (512 Bytes)
6300h−6307h
Mailbox 0
6308h−630Fh
Mailbox 1
6310h−6317h
Mailbox 2
6318h−631Fh
Mailbox 3
6320h−6327h
Mailbox 4
Mailbox Interrupt Mask − CANMIM
Mailbox Interrupt Level − CANMIL
Overwrite Protection Control − CANOPC
TX I/O Control − CANTIOC
RX I/O Control − CANRIOC
Time Stamp Counter − CANTSC
Time-Out Control − CANTOC
Time-Out Status − CANTOS
63E0h−63E7h
Mailbox 28
63E8h−63EFh
Mailbox 29
63F0h−63F7h
Mailbox 30
63F8h−63FFh
Mailbox 31
Reserved
Message Mailbox (16 Bytes)
63E8h−63E9h
Message Identifier − MSGID
63EAh−63EBh
Message Control − MSGCTRL
63ECh−63EDh
Message Data Low − MDL
63EEh−63EFh
Message Data High − MDH
Figure 4-12. eCAN-B Memory Map
The CAN registers listed in Table 4-7 are used by the CPU to configure and control the CAN controller
and the message objects. eCAN control registers only support 32-bit read/write operations. Mailbox RAM
can be accessed as 16 bits or 32 bits. 32-bit accesses are aligned to an even boundary.
60
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 4-7. CAN Register Map (1)
REGISTER NAME
ECAN-A
ADDRESS
ECAN-B
ADDRESS
SIZE
(x32)
(1)
DESCRIPTION
CANME
0x6000
0x6200
1
Mailbox enable
CANMD
0x6002
0x6202
1
Mailbox direction
CANTRS
0x6004
0x6204
1
Transmit request set
CANTRR
0x6006
0x6206
1
Transmit request reset
CANTA
0x6008
0x6208
1
Transmission acknowledge
CANAA
0x600A
0x620A
1
Abort acknowledge
CANRMP
0x600C
0x620C
1
Receive message pending
CANRML
0x600E
0x620E
1
Receive message lost
CANRFP
0x6010
0x6210
1
Remote frame pending
CANGAM
0x6012
0x6212
1
Global acceptance mask
CANMC
0x6014
0x6214
1
Master control
CANBTC
0x6016
0x6216
1
Bit-timing configuration
CANES
0x6018
0x6218
1
Error and status
CANTEC
0x601A
0x621A
1
Transmit error counter
CANREC
0x601C
0x621C
1
Receive error counter
CANGIF0
0x601E
0x621E
1
Global interrupt flag 0
CANGIM
0x6020
0x6220
1
Global interrupt mask
CANGIF1
0x6022
0x6222
1
Global interrupt flag 1
CANMIM
0x6024
0x6224
1
Mailbox interrupt mask
CANMIL
0x6026
0x6226
1
Mailbox interrupt level
CANOPC
0x6028
0x6228
1
Overwrite protection control
CANTIOC
0x602A
0x622A
1
TX I/O control
CANRIOC
0x602C
0x622C
1
RX I/O control
CANTSC
0x602E
0x622E
1
Time stamp counter (Reserved in SCC mode)
CANTOC
0x6030
0x6230
1
Time-out control (Reserved in SCC mode)
CANTOS
0x6032
0x6232
1
Time-out status (Reserved in SCC mode)
These registers are mapped to Peripheral Frame 1.
Submit Documentation Feedback
Peripherals
61
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
4.8
Serial Communications Interface (SCI) Modules (SCI-A, SCI-B)
The 280x devices include two serial communications interface (SCI) modules. The SCI modules support
digital communications between the CPU and other asynchronous peripherals that use the standard
non-return-to-zero (NRZ) format. The SCI receiver and transmitter are double-buffered, and each has its
own separate enable and interrupt bits. Both can be operated independently or simultaneously in the
full-duplex mode. To ensure data integrity, the SCI checks received data for break detection, parity,
overrun, and framing errors. The bit rate is programmable to over 65000 different speeds through a 16-bit
baud-select register.
Features of each SCI module include:
• Two external pins:
– SCITXD: SCI transmit-output pin
– SCIRXD: SCI receive-input pin
NOTE: Both pins can be used as GPIO if not used for SCI.
– Baud rate programmable to 64K different rates:
•
•
•
•
•
•
•
•
•
•
Baud rate =
LSPCLK
(BRR ) 1) * 8
when BRR ≠ 0
Baud rate =
LSPCLK
16
when BRR = 0
Data-word format
– One start bit
– Data-word length programmable from one to eight bits
– Optional even/odd/no parity bit
– One or two stop bits
Four error-detection flags: parity, overrun, framing, and break detection
Two wake-up multiprocessor modes: idle-line and address bit
Half- or full-duplex operation
Double-buffered receive and transmit functions
Transmitter and receiver operations can be accomplished through interrupt-driven or polled algorithms
with status flags.
– Transmitter: TXRDY flag (transmitter-buffer register is ready to receive another character) and TX
EMPTY flag (transmitter-shift register is empty)
– Receiver: RXRDY flag (receiver-buffer register is ready to receive another character), BRKDT flag
(break condition occurred), and RX ERROR flag (monitoring four interrupt conditions)
Separate enable bits for transmitter and receiver interrupts (except BRKDT)
Max bit rate + 100 MHz + 6.25 106 bńs
16
NRZ (non-return-to-zero) format
Ten SCI module control registers located in the control register frame beginning at address 7050h
NOTE
All registers in this module are 8-bit registers that are connected to Peripheral Frame 2.
When a register is accessed, the register data is in the lower byte (7-0), and the upper
byte (15-8) is read as zeros. Writing to the upper byte has no effect.
Enhanced features:
• Auto baud-detect hardware logic
• 16-level transmit/receive FIFO
The SCI port operation is configured and controlled by the registers listed in Table 4-8 and Table 4-9.
62
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 4-8. SCI-A Registers (1)
(1)
(2)
NAME
ADDRESS
SIZE (x16)
SCICCRA
0x7050
1
SCI-A Communications Control Register
DESCRIPTION
SCICTL1A
0x7051
1
SCI-A Control Register 1
SCIHBAUDA
0x7052
1
SCI-A Baud Register, High Bits
SCILBAUDA
0x7053
1
SCI-A Baud Register, Low Bits
SCICTL2A
0x7054
1
SCI-A Control Register 2
SCIRXSTA
0x7055
1
SCI-A Receive Status Register
SCIRXEMUA
0x7056
1
SCI-A Receive Emulation Data Buffer Register
SCIRXBUFA
0x7057
1
SCI-A Receive Data Buffer Register
SCITXBUFA
0x7059
1
SCI-A Transmit Data Buffer Register
SCIFFTXA (2)
0x705A
1
SCI-A FIFO Transmit Register
SCIFFRXA (2)
0x705B
1
SCI-A FIFO Receive Register
SCIFFCTA (2)
0x705C
1
SCI-A FIFO Control Register
SCIPRIA
0x705F
1
SCI-A Priority Control Register
Registers in this table are mapped to Peripheral Frame 2 space. This space only allows 16-bit accesses. 32-bit accesses produce
undefined results.
These registers are new registers for the FIFO mode.
Table 4-9. SCI-B Registers (1) (2)
(1)
(2)
NAME
ADDRESS
SIZE (x16)
SCICCRB
0x7750
1
SCI-B Communications Control Register
DESCRIPTION
SCICTL1B
0x7751
1
SCI-B Control Register 1
SCIHBAUDB
0x7752
1
SCI-B Baud Register, High Bits
SCILBAUDB
0x7753
1
SCI-B Baud Register, Low Bits
SCICTL2B
0x7754
1
SCI-B Control Register 2
SCIRXSTB
0x7755
1
SCI-B Receive Status Register
SCIRXEMUB
0x7756
1
SCI-B Receive Emulation Data Buffer Register
SCIRXBUFB
0x7757
1
SCI-B Receive Data Buffer Register
SCITXBUFB
0x7759
1
SCI-B Transmit Data Buffer Register
SCIFFTXB (2)
0x775A
1
SCI-B FIFO Transmit Register
SCIFFRXB (2)
0x775B
1
SCI-B FIFO Receive Register
SCIFFCTB (2)
0x775C
1
SCI-B FIFO Control Register
SCIPRIB
0x775F
1
SCI-B Priority Control Register
Registers in this table are mapped to peripheral bus 16 space. This space only allows 16-bit accesses. 32-bit accesses produce
undefined results.
These registers are new registers for the FIFO mode.
Submit Documentation Feedback
Peripherals
63
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Figure 4-13 shows the SCI module block diagram.
SCICTL1.1
SCITXD
Frame Format and Mode
Parity
Even/Odd Enable
TXSHF
Register
TXENA
8
SCICCR.6 SCICCR.5
TX EMPTY
SCICTL2.6
TXRDY
TXWAKE
SCICTL1.3
1
Transmitter-Data
Buffer Register
8
TX INT ENA
SCICTL2.7
SCICTL2.0
TX FIFO
Interrupts
TX FIFO _0
TX FIFO _1
SCITXD
TXINT
TX Interrupt
Logic
-----
To CPU
TX FIFO _15
WUT
SCI TX Interrupt select logic
SCITXBUF.7-0
TX FIFO registers
SCIFFENA
AutoBaud Detect logic
SCIFFTX.14
SCIHBAUD. 15 - 8
Baud Rate
MSbyte
Register
SCIRXD
RXSHF
Register
SCIRXD
RXWAKE
LSPCLK
SCIRXST.1
SCILBAUD. 7 - 0
Baud Rate
LSbyte
Register
RXENA
8
SCICTL1.0
SCICTL2.1
Receive Data
Buffer register
SCIRXBUF.7-0
RXRDY
8
BRKDT
RX FIFO _15
----RX FIFO_1
RX FIFO _0
SCIRXBUF.7-0
RX/BK INT ENA
SCIRXST.6
SCIRXST.5
RX FIFO
Interrupts
RX Interrupt
Logic
To CPU
RX FIFO registers
SCIRXST.7
SCIRXST.4 - 2
RX Error
FE OE PE
RXINT
RXFFOVF
SCIFFRX.15
RX Error
RX ERR INT ENA
SCICTL1.6
SCI RX Interrupt select logic
Figure 4-13. Serial Communications Interface (SCI) Module Block Diagram
64
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
4.9
Serial Peripheral Interface (SPI) Modules (SPI-A, SPI-B, SPI-C, SPI-D)
The 280x devices include the four-pin serial peripheral interface (SPI) module. Up to four SPI modules
(SPI-A, SPI-B, SPI-C, and SPI-D) are available. The SPI is a high-speed, synchronous serial I/O port that
allows a serial bit stream of programmed length (one to sixteen bits) to be shifted into and out of the
device at a programmable bit-transfer rate. Normally, the SPI is used for communications between the
DSP controller and external peripherals or another processor. Typical applications include external I/O or
peripheral expansion through devices such as shift registers, display drivers, and ADCs. Multidevice
communications are supported by the master/slave operation of the SPI.
The SPI module features include:
• Four external pins:
– SPISOMI: SPI slave-output/master-input pin
– SPISIMO: SPI slave-input/master-output pin
– SPISTE: SPI slave transmit-enable pin
– SPICLK: SPI serial-clock pin
NOTE: All four pins can be used as GPIO, if the SPI module is not used.
• Two operational modes: master and slave
Baud rate: 125 different programmable rates.
•
•
•
•
•
Baud rate =
LSPCLK
(SPIBRR ) 1)
Baud rate =
LSPCLK
4
when SPIBRR = 3 to 127
when SPIBRR = 0,1, 2
Data word length: one to sixteen data bits
Four clocking schemes (controlled by clock polarity and clock phase bits) include:
– Falling edge without phase delay: SPICLK active-high. SPI transmits data on the falling edge of the
SPICLK signal and receives data on the rising edge of the SPICLK signal.
– Falling edge with phase delay: SPICLK active-high. SPI transmits data one half-cycle ahead of the
falling edge of the SPICLK signal and receives data on the falling edge of the SPICLK signal.
– Rising edge without phase delay: SPICLK inactive-low. SPI transmits data on the rising edge of the
SPICLK signal and receives data on the falling edge of the SPICLK signal.
– Rising edge with phase delay: SPICLK inactive-low. SPI transmits data one half-cycle ahead of the
falling edge of the SPICLK signal and receives data on the rising edge of the SPICLK signal.
Simultaneous receive and transmit operation (transmit function can be disabled in software)
Transmitter and receiver operations are accomplished through either interrupt-driven or polled
algorithms.
Nine SPI module control registers: Located in control register frame beginning at address 7040h.
NOTE
All registers in this module are 16-bit registers that are connected to Peripheral Frame 2.
When a register is accessed, the register data is in the lower byte (7-0), and the upper
byte (15-8) is read as zeros. Writing to the upper byte has no effect.
Enhanced feature:
• 16-level transmit/receive FIFO
• Delayed transmit control
The SPI port operation is configured and controlled by the registers listed in Table 4-10.
Submit Documentation Feedback
Peripherals
65
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 4-10. SPI-A Registers
(1)
DESCRIPTION (1)
NAME
ADDRESS
SIZE (X16)
SPICCR
0x7040
1
SPI-A Configuration Control Register
SPICTL
0x7041
1
SPI-A Operation Control Register
SPISTS
0x7042
1
SPI-A Status Register
SPIBRR
0x7044
1
SPI-A Baud Rate Register
SPIRXEMU
0x7046
1
SPI-A Receive Emulation Buffer Register
SPIRXBUF
0x7047
1
SPI-A Serial Input Buffer Register
SPITXBUF
0x7048
1
SPI-A Serial Output Buffer Register
SPIDAT
0x7049
1
SPI-A Serial Data Register
SPIFFTX
0x704A
1
SPI-A FIFO Transmit Register
SPIFFRX
0x704B
1
SPI-A FIFO Receive Register
SPIFFCT
0x704C
1
SPI-A FIFO Control Register
SPIPRI
0x704F
1
SPI-A Priority Control Register
Registers in this table are mapped to Peripheral Frame 2. This space only allows 16-bit accesses. 32-bit accesses produce undefined
results.
Table 4-11. SPI-B Registers
(1)
66
DESCRIPTION (1)
NAME
ADDRESS
SIZE (X16)
SPICCR
0x7740
1
SPI-B Configuration Control Register
SPICTL
0x7741
1
SPI-B Operation Control Register
SPISTS
0x7742
1
SPI-B Status Register
SPIBRR
0x7744
1
SPI-B Baud Rate Register
SPIRXEMU
0x7746
1
SPI-B Receive Emulation Buffer Register
SPIRXBUF
0x7747
1
SPI-B Serial Input Buffer Register
SPITXBUF
0x7748
1
SPI-B Serial Output Buffer Register
SPIDAT
0x7749
1
SPI-B Serial Data Register
SPIFFTX
0x774A
1
SPI-B FIFO Transmit Register
SPIFFRX
0x774B
1
SPI-B FIFO Receive Register
SPIFFCT
0x774C
1
SPI-B FIFO Control Register
SPIPRI
0x774F
1
SPI-B Priority Control Register
Registers in this table are mapped to Peripheral Frame 2. This space only allows 16-bit accesses. 32-bit accesses produce undefined
results.
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 4-12. SPI-C Registers
(1)
DESCRIPTION (1)
NAME
ADDRESS
SIZE (X16)
SPICCR
0x7760
1
SPI-C Configuration Control Register
SPICTL
0x7761
1
SPI-C Operation Control Register
SPISTS
0x7762
1
SPI-C Status Register
SPIBRR
0x7764
1
SPI-C Baud Rate Register
SPIRXEMU
0x7766
1
SPI-C Receive Emulation Buffer Register
SPIRXBUF
0x7767
1
SPI-C Serial Input Buffer Register
SPITXBUF
0x7768
1
SPI-C Serial Output Buffer Register
SPIDAT
0x7769
1
SPI-C Serial Data Register
SPIFFTX
0x776A
1
SPI-C FIFO Transmit Register
SPIFFRX
0x776B
1
SPI-C FIFO Receive Register
SPIFFCT
0x776C
1
SPI-C FIFO Control Register
SPIPRI
0x776F
1
SPI-C Priority Control Register
Registers in this table are mapped to Peripheral Frame 2. This space only allows 16-bit accesses. 32-bit accesses produce undefined
results.
Table 4-13. SPI-D Registers
(1)
DESCRIPTION (1)
NAME
ADDRESS
SIZE (X16)
SPICCR
0x7780
1
SPI-D Configuration Control Register
SPICTL
0x7781
1
SPI-D Operation Control Register
SPISTS
0x7782
1
SPI-D Status Register
SPIBRR
0x7784
1
SPI-D Baud Rate Register
SPIRXEMU
0x7786
1
SPI-D Receive Emulation Buffer Register
SPIRXBUF
0x7787
1
SPI-D Serial Input Buffer Register
SPITXBUF
0x7788
1
SPI-D Serial Output Buffer Register
SPIDAT
0x7789
1
SPI-D Serial Data Register
SPIFFTX
0x778A
1
SPI-D FIFO Transmit Register
SPIFFRX
0x778B
1
SPI-D FIFO Receive Register
SPIFFCT
0x778C
1
SPI-D FIFO Control Register
SPIPRI
0x778F
1
SPI-D Priority Control Register
Registers in this table are mapped to Peripheral Frame 2. This space only allows 16-bit accesses. 32-bit accesses produce undefined
results.
Submit Documentation Feedback
Peripherals
67
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Figure 4-14 is a block diagram of the SPI in slave mode.
SPIFFENA
Overrun
INT ENA
Receiver
Overrun Flag
SPIFFTX.14
RX FIFO registers
SPISTS.7
SPICTL.4
SPIRXBUF
RX FIFO _0
RX FIFO _1
−−−−−
SPIINT/SPIRXINT
RX FIFO Interrupt
RX Interrupt
Logic
RX FIFO _15
16
SPIRXBUF
Buffer Register
SPIFFOVF FLAG
SPIFFRX.15
To CPU
TX FIFO registers
SPITXBUF
TX FIFO _15
−−−−−
TX Interrupt
Logic
TX FIFO Interrupt
TX FIFO _1
TX FIFO _0
SPITXINT
16
SPI INT FLAG
SPITXBUF
Buffer Register
16
SPI INT
ENA
SPISTS.6
SPICTL.0
16
M
M
SPIDAT
Data Register
S
S
SW1
SPISIMO
M
M
SPIDAT.15 − 0
S
S
SW2
SPISOMI
Talk
SPICTL.1
SPISTE(A)
State Control
Master/Slave
SPI Char
SPICCR.3 − 0
3
2
1
SW3
M
SPI Bit Rate
LSPCLK
S
SPIBRR.6 − 0
6
A.
SPICTL.2
S
0
5
4
3
2
1
0
Clock
Polarity
Clock
Phase
SPICCR.6
SPICTL.3
SPICLK
M
SPISTE is driven low by the master for a slave device.
Figure 4-14. SPI Module Block Diagram (Slave Mode)
68
Peripherals
Submit Documentation Feedback
www.ti.com
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
4.10 Inter-Integrated Circuit (I2C)
The 280x device contains one I2C Serial Port. Figure 4-15 shows how the I2C peripheral module interfaces
within the 280x device.
The I2C module has the following features:
• Compliance with the Philips Semiconductors I2C-bus specification (version 2.1):
– Support for 1-bit to 8-bit format transfers
– 7-bit and 10-bit addressing modes
– General call
– START byte mode
– Support for multiple master-transmitters and slave-receivers
– Support for multiple slave-transmitters and master-receivers
– Combined master transmit/receive and receive/transmit mode
– Data transfer rate of from 10 kbps up to 400 kbps (Philips Fast-mode rate)
• One 16-bit receive FIFO and one 16-bit transmit FIFO
• One interrupt that can be used by the CPU. This interrupt can be generated as a result of one of the
following conditions:
– Transmit-data ready
– Receive-data ready
– Register-access ready
– No-acknowledgment received
– Arbitration lost
– Stop condition detected
– Addressed as slave
• An additional interrupt that can be used by the CPU when in FIFO mode
• Module enable/disable capability
• Free data format mode
Submit Documentation Feedback
Peripherals
69
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
System Control
Block
C28X CPU
I2CAENCLK
Peripheral Bus
SYSCLKOUT
SYSRS
Control
Data[16]
SDAA
Data[16]
GPIO
MUX
I2C−A
Addr[16]
SCLA
I2CINT1A
PIE
Block
I2CINT2A
A.
The I2C registers are accessed at the SYSCLKOUT rate. The internal timing and signal waveforms of the I2C port are
also at the SYSCLKOUT rate.
B.
The clock enable bit (I2CAENCLK) in the PCLKCRO register turns off the clock to the I2C port for low power
operation. Upon reset, I2CAENCLK is clear, which indicates the peripheral internal clocks are off.
Figure 4-15. I2C Peripheral Module Interfaces
The registers in Table 4-14 configure and control the I2C port operation.
Table 4-14. I2C-A Registers
70
NAME
ADDRESS
I2COAR
0x7900
DESCRIPTION
I2C own address register
I2CIER
0x7901
I2C interrupt enable register
I2CSTR
0x7902
I2C status register
I2CCLKL
0x7903
I2C clock low-time divider register
I2CCLKH
0x7904
I2C clock high-time divider register
I2CCNT
0x7905
I2C data count register
I2CDRR
0x7906
I2C data receive register
I2CSAR
0x7907
I2C slave address register
I2CDXR
0x7908
I2C data transmit register
I2CMDR
0x7909
I2C mode register
I2CISRC
0x790A
I2C interrupt source register
I2CPSC
0x790C
I2C prescaler register
I2CFFTX
0x7920
I2C FIFO transmit register
I2CFFRX
0x7921
I2C FIFO receive register
I2CRSR
-
I2C receive shift register (not accessible to the CPU)
I2CXSR
-
I2C transmit shift register (not accessible to the CPU)
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
4.11 GPIO MUX
On the 280x, the GPIO MUX can multiplex up to three independent peripheral signals on a single GPIO
pin in addition to providing individual pin bit-banging IO capability. The GPIO MUX block diagram per pin
is shown in Figure 4-16. Because of the open drain capabilities of the I2C pins, the GPIO MUX block
diagram for these pins differ. See the TMS320x280x System Control and Interrupts Reference Guide
(literature number SPRU712) for details.
GPIOXINT1SEL
GPIOLMPSEL
GPIOXINT2SEL
LPMCR0
GPIOXNMISEL
External Interrupt
MUX
Low Power
Modes Block
Asynchronous
path
GPxDAT (read)
GPxQSEL1/2
GPxCTRL
GPxPUD
00
Input
Qualification
Internal
Pullup
PIE
N/C
01
Peripheral 1 Input
10
Peripheral 2 Input
11
Peripheral 3 Input
GPxTOGGLE
Asynchronous path
GPIOx pin
GPxCLEAR
GPxSET
00
GPxDAT (latch)
01
Peripheral 1 Output
10
Peripheral 2 Output
11
Peripheral 3 Output
00
GPxDIR (latch)
High Impedance
Output Control
0 = Input, 1 = Output
XRS
= Default at Reset
01
Peripheral 1 Output Enable
10
Peripheral 2 Output Enable
11
Peripheral 3 Output Enable
GPxMUX1/2
A.
x stands for the port, either A or B. For example, GPxDIR refers to either the GPADIR and GPBDIR register
depending on the particular GPIO pin selected.
B.
GPxDAT latch/read are accessed at the same memory location.
Figure 4-16. GPIO MUX Block Diagram
Submit Documentation Feedback
Peripherals
71
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
The 280x supports 34 GPIO pins. The GPIO control and data registers are mapped to Peripheral Frame 1
to enable 32-bit operations on the registers (along with 16-bit operations). Table 4-15 shows the GPIO
register mapping.
Table 4-15. GPIO Registers
NAME
ADDRESS
SIZE (x16)
DESCRIPTION
GPIO CONTROL REGISTERS (EALLOW PROTECTED)
GPACTRL
0x6F80
2
GPIO A Control Register (GPIO0 to 31)
GPAQSEL1
0x6F82
2
GPIO A Qualifier Select 1 Register (GPIO0 to 15)
GPAQSEL2
0x6F84
2
GPIO A Qualifier Select 2 Register (GPIO16 to 31)
GPAMUX1
0x6F86
2
GPIO A MUX 1 Register (GPIO0 to 15)
GPAMUX2
0x6F88
2
GPIO A MUX 2 Register (GPIO16 to 31)
GPADIR
0x6F8A
2
GPIO A Direction Register (GPIO0 to 31)
GPAPUD
0x6F8C
2
GPIO A Pull Up Disable Register (GPIO0 to 31)
reserved
0x6F8E
0x6F8F
2
GPBCTRL
0x6F90
2
GPIO B Control Register (GPIO32 to 35)
GPBQSEL1
0x6F92
2
GPIO B Qualifier Select 1 Register (GPIO32 to 35)
GPBQSEL2
0x6F94
2
reserved
GPBMUX1
0x6F96
2
GPIO B MUX 1 Register (GPIO32 to 35)
GPBMUX2
0x6F98
2
reserved
GPBDIR
0x6F9A
2
GPIO B Direction Register (GPIO32 to 35)
GPBPUD
0x6F9C
2
GPIO B Pull Up Disable Register (GPIO32 to 35)
reserved
0x6F9E
0x6F9F
2
reserved
reserved
0x6FA0
0x6FBF
32
GPADAT
0x6FC0
2
GPIO Data Register (GPIO0 to 31)
GPIO DATA REGISTERS (NOT EALLOW PROTECTED)
GPASET
0x6FC2
2
GPIO Data Set Register (GPIO0 to 31)
GPACLEAR
0x6FC4
2
GPIO Data Clear Register (GPIO0 to 31)
GPATOGGLE
0x6FC6
2
GPIO Data Toggle Register (GPIO0 to 31)
GPBDAT
0x6FC8
2
GPIO Data Register (GPIO32 to 35)
GPBSET
0x6FCA
2
GPIO Data Set Register (GPIO32 to 35)
GPBCLEAR
0x6FCC
2
GPIO Data Clear Register (GPIO32 to 35)
GPBTOGGLE
0x6FCE
2
GPIO Data Toggle Register (GPIO32 to 35)
reserved
0x6FD0
0x6FDF
16
GPIO INTERRUPT AND LOW POWER MODES SELECT REGISTERS (EALLOW PROTECTED)
72
GPIOXINT1SEL
0x6FE0
1
XINT1 GPIO Input Select Register (GPIO0 to 31)
GPIOXINT2SEL
0x6FE1
1
XINT2 GPIO Input Select Register (GPIO0 to 31)
GPIOXNMISEL
0x6FE2
1
XNMI GPIO Input Select Register (GPIO0 to 31)
reserved
0x6FE3
0x6FE7
5
GPIOLPMSEL
0x6FE8
2
reserved
0x6FEA
0x6FFF
22
Peripherals
LPM GPIO Select Register (GPIO0 to 31)
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 4-16. F2808 GPIO MUX Table
DEFAULT AT RESET
PRIMARY I/O
FUNCTION
(GPxMUX1/2 BITS =
0,0)
PERIPHERAL SELECTION
1 (2)
(GPxMUX1/2 BITS = 0,1)
1-0
GPIO0
3-2
GPIO1
GPAMUX1/2 (1)
REGISTER
BITS
PERIPHERAL SELECTION 2
(GPxMUX1/2 BITS = 1,0)
PERIPHERAL SELECTION 3
(GPxMUX1/2 BITS = 1,1)
EPWM1A (O)
Reserved (3)
Reserved (3)
EPWM1B (O)
SPISIMOD (I/O)
Reserved (3)
Reserved (3)
GPAMUX1
5-4
GPIO2
EPWM2A (O)
Reserved (3)
7-6
GPIO3
EPWM2B (O)
SPISOMID (I/O)
Reserved (3)
9-8
GPIO4
EPWM3A (O)
Reserved (3)
Reserved (3)
11-10
GPIO5
EPWM3B (O)
SPICLKD (I/O)
ECAP1 (I/O)
13-12
GPIO6
EPWM4A (O)
EPWMSYNCI (I)
EPWMSYNCO (O)
15-14
GPIO7
EPWM4B (O)
SPISTED (I/O)
ECAP2 (I/O)
17-16
GPIO8
EPWM5A (O)
CANTXB (O)
ADCSOCAO (O)
19-18
GPIO9
EPWM5B (O)
SCITXDB (O)
ECAP3 (I/O)
21-20
GPIO10
EPWM6A (O)
CANRXB (I)
ADCSOCBO (O)
23-22
GPIO11
EPWM6B (O)
SCIRXDB (I)
ECAP4 (I/O)
25-24
GPIO12
TZ1 (I)
CANTXB (O)
SPISIMOB (I/O)
27-26
GPIO13
TZ2 (I)
CANRXB (I)
SPISOMIB (I/O)
29-28
GPIO14
TZ3 (I)
SCITXDB (O)
SPICLKB (I/O)
31-30
GPIO15
TZ4 (I)
SCIRXDB (I)
SPISTEB (I/O)
GPAMUX2
1-0
GPIO16
SPISIMOA (I/O)
CANTXB (O)
TZ5 (I)
3-2
GPIO17
SPISOMIA (I/O)
CANRXB (I)
TZ6 (I)
5-4
GPIO18
SPICLKA (I/O)
SCITXDB (O)
Reserved (3)
7-6
GPIO19
SPISTEA (I/O)
SCIRXDB (I)
Reserved (3)
9-8
GPIO20
EQEP1A (I)
SPISIMOC (I/O)
CANTXB (O)
11-10
GPIO21
EQEP1B (I)
SPISOMIC (I/O)
CANRXB (I)
13-12
GPIO22
EQEP1S (I/O)
SPICLKC (I/O)
SCITXDB (O)
15-14
GPIO23
EQEP1I (I/O)
SPISTEC (I/O)
SCIRXDB (I)
17-16
GPIO24
ECAP1 (I/O)
EQEP2A (I)
SPISIMOB (I/O)
19-18
GPIO25
ECAP2 (I/O)
EQEP2B (I)
SPISOMIB (I/O)
21-20
GPIO26
ECAP3 (I/O)
EQEP2I (I/O)
SPICLKB (I/O)
23-22
GPIO27
ECAP4 (I/O)
EQEP2S (I/O)
SPISTEB (I/O)
25-24
GPIO28
SCIRXDA (I)
Reserved (3)
TZ5 (I)
27-26
GPIO29
SCITXDA (O)
Reserved (3)
TZ6 (I)
29-28
GPIO30
CANRXA (I)
Reserved (3)
Reserved (3)
Reserved (3)
Reserved (3)
31-30
GPIO31
CANTXA (O)
1-0
GPIO32
SDAA (I/OC)
EPWMSYNCI (I)
ADCSOCAO (O)
3-2
GPIO33
SCLA (I/OC)
EPWMSYNCO (O)
ADCSOCBO (O)
5-4
GPIO34
Reserved (3)
Reserved (3)
Reserved (3)
GPBMUX1
(1)
(2)
(3)
GPxMUX1/2 refers to the appropriate MUX register for the pin; GPAMUX1, GPAMUX2 or GPBMUX1.
This table pertains to the 2808 device. Some peripherals may not be available in the 2806 or 2801 devices. See the pin descriptions for
more detail.
The word "Reserved" means that there is no peripheral assigned to this GPxMUX1/2 register setting. Should it be selected, the state of
the pin will be undefined and the pin may be driven. This selection is a reserved configuration for future expansion.
Submit Documentation Feedback
Peripherals
73
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
The user can select the type of input qualification for each GPIO pin via the GPxQSEL1/2 registers from
four choices:
• Synchronization To SYSCLKOUT Only (GPxQSEL1/2=0,0): This is the default mode of all GPIO pins
at reset and it simply synchronizes the input signal to the system clock (SYSCLKOUT).
• Qualification Using Sampling Window (GPxQSEL1/2=0,1 and 1,0): In this mode the input signal, after
synchronization to the system clock (SYSCLKOUT), is qualified by a specified number of cycles before
the input is allowed to change.
Time between samples
GPyCTRL Reg
GPIOx
SYNC
Qualification
Input Signal
Qualified By 3
or 6 Samples
GPxQSEL
SYSCLKOUT
Number of Samples
Figure 4-17. Qualification Using Sampling Window
•
•
The sampling period is specified by the QUALPRD bits in the GPxCTRL register and is configurable in
groups of 8 signals. It specifies a multiple of SYSCLKOUT cycles for sampling the input signal. The
sampling window is either 3-samples or 6-samples wide and the output is only changed when ALL
samples are the same (all 0s or all 1s) as shown in Figure 4-18 (for 6 sample mode).
No Synchronization (GPxQSEL1/2=1,1): This mode is used for peripherals where synchronization is
not required (synchronization is performed within the peripheral).
Due to the multi-level multiplexing that is required on the 280x device, there may be cases where a
peripheral input signal can be mapped to more then one GPIO pin. Also, when an input signal is not
selected, the input signal will default to either a 0 or 1 state, depending on the peripheral.
74
Peripherals
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
5
Device Support
Texas Instruments (Texas Instruments) offers an extensive line of development tools for the C28x™
generation of DSPs, including tools to evaluate the performance of the processors, generate code,
develop algorithm implementations, and fully integrate and debug software and hardware modules.
The following products support development of 280x-based applications:
Software Development Tools
• Code Composer Studio™ Integrated Development Environment (IDE)
– C/C++ Compiler
– Code generation tools
– Assembler/Linker
– Cycle Accurate Simulator
• Application algorithms
• Sample applications code
Hardware Development Tools
• 2808 eZdsp™
• JTAG-based emulators - SPI515, XDS510PP, XDS510PP Plus, XDS510USB™
• Universal 5-V dc power supply
• Documentation and cables
5.1
Device and Development Support Tool Nomenclature
To designate the stages in the product development cycle, Texas Instruments assigns prefixes to the part
numbers of all TMS320™ DSP devices and support tools. Each TMS320™ DSP commercial family
member has one of three prefixes: TMX, TMP, or TMS. Texas Instruments recommends two of three
possible prefix designators for its support tools: TMDX and TMDS. These prefixes represent evolutionary
stages of product development from engineering prototypes (TMX/TMDX) through fully qualified
production devices/tools (TMS/TMDS).
Device development evolutionary flow:
TMX
Experimental device that is not necessarily representative of the final device's electrical
specifications
TMP
Final silicon die that conforms to the device's electrical specifications but has not completed
quality and reliability verification
TMS
Fully qualified production device
Support tool development evolutionary flow:
TMDX
Development-support product that has not yet completed Texas Instruments internal qualification
testing
TMDS
Fully qualified development-support product
TMX and TMP devices and TMDX development-support tools are shipped against the following
disclaimer:
"Developmental product is intended for internal evaluation purposes."
TMS devices and TMDS development-support tools have been characterized fully and the quality and
reliability of the device have been demonstrated fully. Texas Instruments standard warranty applies.
Submit Documentation Feedback
Device Support
75
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Predictions show that prototype devices (TMX or TMP) have a greater failure rate than the standard
production devices. Texas Instruments recommends that these devices not be used in any production
system because their expected end-use failure rate still is undefined. Only qualified production devices are
to be used.
Texas Instruments device nomenclature also includes a suffix with the device family name. This suffix
indicates the package type (for example, PBK) and temperature range (for example, A). Figure 5-1
provides a legend for reading the complete device name for any family member.
SM
320
F
2808
PZ
M
4/(4*,+ 2(9:0*
" "# 5 :5 5
!
5 :5 5
5 :5 5
5 :5 5
%
!
533,8*0(2 85*,9904.
"&
'
>604 25< 685-02, 7;(+
-2(:6(*1 >)(22 )(22 .80+ (88(= ' >)(22 2,(+>-8,,
DEVICE FAMILY
"!
E ! (302=
$
"&
2(9/ >$ 58,
>$ Figure 5-1. Example of SM320x280x Device Nomenclature
X
' )& UCD
9501
PZ
A
#2+#-%(#). ' "#0%!#
,/ '%$%#" "#0%!#
5 .* 5
4+%) '*1 +-*$%'# ,/ "
$' .+ !& DEVICE FAMILY
(%'3
Figure 5-2. Example of UCD Device Nomenclature
5.2
Documentation Support
Extensive documentation supports all of the TMS320™ DSP family generations of devices from product
announcement through applications development. The types of documentation available include: data
sheets and data manuals, with design specifications; and hardware and software applications.
TMS320x280x device reference guides are applicable to the UCD9501 device as well. Useful reference
documentation includes:
76
SPRU051:
TMS320x281x, 280x Serial Communication Interface (SCI) Reference Guide
Describes the SCI, which is a two-wire asynchronous serial port, commonly known as a
UART. The SCI modules support digital communications between the CPU and other
asynchronous peripherals that use the standard non-return-to-zero (NRZ) format.
SPRU059:
TMS320x281x, 280x Serial Peripheral Interface (SPI) Reference Guide
Describes the SPI - a high-speed synchronous serial input/output (I/O) port that allows a
serial bit stream of programmed length (one to sixteen bits) to be shifted into and out of the
Device Support
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
device at a programmed bit-transfer rate. The SPI is used for communications between the
DSP controller and external peripherals or another controller.
SPRU074:
TMS320x281x, 280x Enhanced Controller Area Network (eCAN) Reference Guide
Describes the eCAN that uses established protocol to communicate serially with other
controllers in electrically noisy environments. With 32 fully configurable mailboxes and
time-stamping feature, the eCAN module provides a versatile and robust serial
communication interface. The eCAN module implemented in the 281x DSP is compatible
with the CAN 2.0B standard (active).
SPRU430:
TMS320C28x DSP CPU and Instruction Set Reference Guide
Describes the central processing unit (CPU) and the assembly language instructions of the
TMS320C28x fixed-point digital signal processors (DSPs). It also describes emulation
features available on these DSPs.
SPRU513:
TMS320C28x Assembly Language Tools User's Guide
Describes the assembly language tools (assembler and other tools used to develop
assembly language code), assembler directives, macros, common object file format, and
symbolic debugging directives for the TMS320C28x device.
SPRU514:
TMS320C28x Optimizing C Compiler User's Guide
describes the TMS320C28x C/C++ compiler. This compiler accepts ANSI standard C/C++
source code and produces TMS320 DSP assembly language source code for the
TMS320C28x device.
SPRU566:
TMS320x281x, 280x Peripheral Reference Guide
Describes the peripheral reference guides of the 28x digital signal processors (DSPs).
SPRU608:
The TMS320C28x Instruction Set Simulator Technical Overview
Describes the simulator, available within the Code Composer Studio for TMS320C2000 IDE,
that simulates the instruction set of the C28x core.
SPRU625:
TMS320C28x DSP/BIOS Application Programming Interface (API) Reference Guide
Describes development using DSP/BIOS.
SPRU712:
TMS320x280x System Control and Interrupts Reference Guide
Describes the various interrupts and system control features of the 280x digital signal
processors (DSPs).
SPRU716:
TMS320x280x Analog-to-Digital Converter (ADC) Reference Guide
Describes the ADC module. The module is a 12-bit pipelined ADC. The analog circuits of
this converter, referred to as the core in this document, include the front-end analog
multiplexers (MUXs), sample-and-hold (S/H) circuits, the conversion core, voltage regulators,
and other analog supporting circuits. Digital circuits, referred to as the wrapper in this
document, include programmable conversion sequencer, result registers, interface to analog
circuits, interface to device peripheral bus, and interface to other on-chip modules.
SPRU722:
TMS320x280x Boot ROM Reference Guide
Describes the purpose and features of the bootloader (factory-programmed boot-loading
software). It also describes other contents of the device on-chip boot ROM and identifies
where all of the information is located within that memory.
SPRU790:
TMS320x280x Enhanced Quadrature Encoder Pulse (eQEP) Reference Guide
Describes the eQEP module, which is used for interfacing with a linear or rotary incremental
encoder to get position, direction, and speed information from a rotating machine in high
performance motion and position control systems. It includes the module description and
registers.
Submit Documentation Feedback
Device Support
77
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
SPRU791:
TMS320x280x Enhanced Pulse Width Modulator (ePWM) Module Reference Guide
The PWM peripheral is an essential part of controlling many of the power related systems
found in both commercial and industrial equipments. This guide describes the main areas
that include digital motor control, switch mode power supply control, UPS (uninterruptible
power supplies), and other forms of power conversion. The PWM peripheral can be
considered as performing a DAC function, where the duty cycle is equivalent to a DAC
analog value, it is sometimes referred to as a Power DAC.
SPRU807:
TMS320x280x Enhanced Capture (eCAP) Module Reference Guide
Describes the enhanced capture module. It includes the module description and registers.
SPRU924:
High-Resolution Pulse Width Modulator (HRPWM) describes the operation of the
high-resolution extension to the pulse width modulator (HRPWM)
SPRA550:
3.3 V DSP for Digital Motor Control describes a scenario of a 3.3-V-only motor controller
indicating that for most applications, no significant issue of interfacing between 3.3 V and 5 V
exists. On-chip 3.3-V analog-to-digital converter (ADC) versus 5-V ADC is also discussed.
Guidelines for component layout and printed circuit board (PCB) design that can reduce
system noise and EMI effects are summarized.
A series of DSP textbooks is published by Prentice-Hall and John Wiley & Sons to support digital signal
processing research and education. The TMS320 DSP newsletter, Details on Signal Processing, is
published quarterly and distributed to update TMS320 DSP customers on product information.
Updated information on the TMS320 DSP controllers can be found on the worldwide web at:
http://www.ti.com.
To send comments regarding this data manual (literature number SPRS230), use the
[email protected] email address, which is a repository for feedback. For questions and support,
contact the Product Information Center listed at the http://www.ti.com/sc/docs/pic/home.htm site.
78
Device Support
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6
Electrical Specifications
This section provides the absolute maximum ratings and the recommended operating conditions for the
TMS320F280x DSPs.
6.1
Absolute Maximum Ratings (1) (2)
Unless otherwise noted, the list of absolute maximum ratings are specified over operating temperature ranges.
Supply voltage range, VDDIO, VDD3VFL
with respect to VSS
-0.3 V to 4.6 V
Supply voltage range, VDDA2, VDDAIO
with respect to VSSA
-0.3 V to 4.6 V
Supply voltage range, VDD
with respect to VSS
-0.3 V to 2.5 V
Supply voltage range, VDD1A18, VDD2A18
with respect to VSSA
-0.3 V to 2.5 V
Supply voltage range, VSSA2, VSSAIO, VSS1AGND, VSS2AGND
with respect to VSS
-0.3 V to 0.3 V
Input voltage range, VIN
-0.3 V to 4.6 V
Output voltage range, VO
-0.3 V to 4.6 V
±20 mA
Input clamp current, IIK (VIN < 0 or VIN > VDDIO) (3)
±20 mA
Output clamp current, IOK (VO < 0 or VO > VDDIO)
Operating ambient temperature ranges, TA (4)
-55°C to 125°C
Junction temperature range, Tj (4)
-55°C to 150°C
Storage temperature range, Tstg
(1)
(2)
(3)
(4)
6.2
(4)
- 65°C to 150°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Section 6.2 is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to VSS, unless otherwise noted.
Continuous clamp current per pin is ± 2 mA. This includes the analog inputs which have an internal clamping circuit that clamps the
voltage to a diode drop above VDDA2 or below VSSA2.
Long-term high-temperature storage and/or extended use at maximum temperature conditions may result in a reduction of overall device
life. For additional information, see IC Package Thermal Metrics Application Report (literature number SPRA953) and Reliability Data for
TMS320LF24x and TMS320F281x Devices Application Report (literature number SPRA963)
Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
Device supply voltage, I/O, VDDIO
3.14
3.3
3.47
V
Device supply voltage CPU, VDD
1.71
1.8
1.89
V
ADC supply voltage (3.3 V), VDDA2, VDDAIO
3.14
3.3
3.47
V
ADC supply voltage (1.8 V), VDD1A18, VDD2A18
1.71
1.8
1.89
V
Flash supply voltage, VDD3VFL
3.14
3.3
3.47
V
MHz
Supply ground, VSS, VSSIO
0
V
Device clock frequency (system clock), fSYSCLKOUT
2
100
High-level input voltage, VIH
2
VDDIO
Low-level input voltage, VIL
High-level output source current, VOH = 2.4 V, IOH
Low-level output sink current, VOL = VOL MAX, IOL
Ambient temperature, TA
(1)
V
0.8
All I/Os except Group 2
-4
Group 2 (1)
-8
All I/Os except Group 2
Group
4
2 (1)
mA
mA
8
-55
125
°C
Group 2 pins are as follows: GPIO28, GPIO29, GPIO30, GPIO31, TDO, XCLKOUT, EMU0, and EMU1
Submit Documentation Feedback
Electrical Specifications
79
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.3
Electrical Characteristics
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
IOH = IOHMAX
TYP
MAX
VOH
High-level output voltage
VOL
Low-level output voltage
IIL
Input current
(low level)
With pullup
VDDIO = 3.3 V, VIN = 0 V
Pullup disabled
VDDIO = 3.3 V, VIN = 0 V
±2
IIH
Input current
(high level)
With pullup
VDDIO = 3.3 V, VIN = VDD
±2
Pullup disabled
VDDIO = 3.3 V, VIN = VDD
IOZ
Output current, high-impedance
state (off-state)
CI
Input capacitance
6.4
UNIT
2.4
IOH = 50 µA
V
VDDIO - 0.2
IOL = IOLMAX
0.4
All I/Os (including XRS)
-80
-140
38
V
-190
50
µA
µA
80
±2
VO = VDDIO or 0 V
µA
2
pF
Current Consumption
Table 6-1. SM320F2808 Current Consumption by Power-Supply Pins at 100-MHz SYSCLKOUT
MODE
Operational
(Flash)
TEST CONDITIONS
•
I2C
All PWM pins are toggled
at 100 kHz.
Data is continuously
transmitted out of the
SCI-A, SCI-B, and
eCAN-A ports. The
hardware multiplier is
exercised.
Code is running out of
flash with 3 wait states.
XCLKOUT is turned off.
•
MAX
MAX
TYP
195 mA
230 mA
15 mA
27 mA
75 mA
90 mA
500 µA
12 mA
Flash is powered down.
Peripheral clocks are off.
6 mA
HALT
Flash is powered down.
Peripheral clocks are off.
Input clock is disabled.
70 µA
80
MAX
TYP (4)
35 mA
40 mA
2 mA
2 µA
100 µA
500 µA
60 µA
120 µA
IDDA33 (3)
MAX
TYP (4)
MAX
30 mA
38 mA
1.5 mA
2 mA
10 µA
5 µA
50 µA
15 µA
30 µA
2 µA
10 µA
5 µA
50 µA
15 µA
30 µA
2 µA
10 µA
5 µA
50 µA
15 µA
30 µA
I2C
STANDBY
(1)
(2)
(3)
(4)
IDDA18 (2)
IDD3VFL
TYP (4)
The following peripheral
clocks are enabled:
•
ePWM1/2/3/4/5/6
•
eCAP1/2/3/4
•
eQEP1/2
•
eCAN-A
•
SCI-A/B
•
SPI-A
•
ADC
Flash is powered down.
XCLKOUT is turned off.
The following peripheral
clocks are enabled:
•
eCAN-A
•
SCI-A
•
SPI-A
IDLE
IDDIO (1)
IDD
TYP (4)
IDDIO current is dependent on the electrical loading on the I/O pins.
IDDA18 includes current into VDD1A18 and VDD2A18 pins.
IDDA33 includes current into VDDA2 and VDDAIO pins.
The TYP numbers are applicable over room temperature and nominal voltage.
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
CAUTION
The peripheral - I/O multiplexing implemented in the 280x devices prevents all
available peripherals from being used at the same time. This is because more than
one peripheral function may share an I/O pin. It is, however, possible to turn on the
clocks to all the peripherals at the same time, although such a configuration is not
useful. If this is done, the current drawn by the device will be more than the numbers
specified in the current consumption tables.
Table 6-2. F2806 Current Consumption by Power-supply Pins at 100 MHz SYSCLKOUT
MODE
Operational
(Flash)
IDLE
TEST CONDITIONS
The following peripheral
clocks are enabled:
•
ePWM1/2/3/4/5/6
•
eCAP1/2/3/4
•
eQEP1/2
•
eCAN-A
•
SCI-A/B
•
SPI-A
•
ADC
•
I2C
All PWM pins are toggled at
100 kHz.
Data is continuously
transmitted out of the
SCI-A, SCI-B, and eCAN-A
ports. The hardware
multiplier is exercised.
Code is running out of flash
with 3 wait states.
XCLKOUT is turned off
Flash is powered down.
XCLKOUT is turned off.
The following peripheral
clocks are enabled:
•
eCAN-A
•
SCI-A
•
SPI-A
•
MAX
TYP (4)
195 mA
230 mA
75 mA
IDDA18 (2)
IDD3VFL
MAX
TYP (4)
MAX
TYP (4)
15 mA
27 mA
35 mA
40 mA
90 mA
500 µA
2 mA
2 µA
12 mA
100 µA
500 µA
60 µA
120 µA
IDDA33 (3)
MAX
TYP (4)
MAX
30 mA
38 mA
1.5 mA
2 mA
10 µA
5 µA
50 µA
15 µA
30 µA
2 µA
10 µA
5 µA
50 µA
15 µA
30 µA
2 µA
10 µA
5 µA
50 µA
15 µA
30 µA
I2C
STANDBY
Flash is powered down.
Peripheral clocks are off.
6 mA
HALT
Flash is powered down.
Peripheral clocks are off.
Input clock is disabled.
70 µA
(1)
(2)
(3)
(4)
IDDIO (1)
IDD
TYP (4)
IDDIO current is dependent on the electrical loading on the I/O pins.
IDDA18 includes current into VDD1A18 and VDD2A18 pins.
IDDA33 includes current into VDDA2 and VDDAIO pins.
The TYP numbers are applicable over room temperature and nominal voltage.
Submit Documentation Feedback
Electrical Specifications
81
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
16
14
Time-to-Fail − Years
12
10
8
6
EM Life
4
2
Wirebond Life
Voiding Effects
0
100 105 110 115 120 125 130 135 140 145 150
TJ − Junction Temperature − °C
G001
Figure 6-1. Wirebond / EM Life for SM320F280xPZMEP
CAUTION
The peripheral - I/O multiplexing implemented in the 280x devices prevents all
available peripherals from being used at the same time. This is because more than
one peripheral function may share an I/O pin. It is, however, possible to turn on the
clocks to all the peripherals at the same time, although such a configuration is not
useful. If this is done, the current drawn by the device will be more than the numbers
specified in the current consumption tables.
Table 6-3. F2801/UCD9501 Current Consumption by Power-supply Pins at 100-MHz SYSCLKOUT
MODE
Operational
(Flash)
(1)
(2)
(3)
(4)
82
TEST CONDITIONS
The following peripheral
clocks are enabled:
•
ePWM1/2/3
•
eCAP1/2
•
eQEP1
•
eCAN-A
•
SCI-A
•
SPI-A
•
ADC
•
I2C
All PWM pins are toggled at
100 kHz.
Data is continuously
transmitted out of the SCI-A,
SCI-B, and eCAN-A ports.
The hardware multiplier is
exercised.
Code is running out of flash
with 3 wait states.
XCLKOUT is turned off.
IDDIO (1)
IDD
IDD3VFL
IDDA18 (2)
IDDA33 (3)
TYP (4)
MAX
TYP (4)
MAX
TYP (4)
MAX
TYP (4)
MAX
TYP (4)
MAX
180 mA
210 mA
15 mA
27 mA
35 mA
40 mA
30 mA
38 mA
1.5 mA
2 mA
IDDIO current is dependent on the electrical loading on the I/O pins.
IDDA18 includes current into VDD1A18 and VDD2A18 pins.
IDDA33 includes current into VDDA2 and VDDAIO pins.
The TYP numbers are applicable over room temperature and nominal voltage.
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-3. F2801/UCD9501 Current Consumption by Power-supply Pins at 100-MHz SYSCLKOUT
(continued)
MODE
Flash is powered down.
XCLKOUT is turned off.
The following peripheral
clocks are enabled:
•
eCAN-A
•
SCI-A
•
SPI-A
IDLE
•
IDDA18 (2)
IDD3VFL
IDDA33 (3)
TYP (4)
MAX
TYP (4)
MAX
TYP (4)
MAX
TYP (4)
MAX
TYP (4)
MAX
75 mA
90 mA
500 µA
2 mA
2 µA
10 µA
5 µA
50 µA
15 µA
30 µA
12 mA
100 µA
500 µA
2 µA
10 µA
5 µA
50 µA
15 µA
30 µA
60 µA
120 µA
2 µA
10 µA
5 µA
50 µA
15 µA
30 µA
I2C
STANDBY
Flash is powered down.
Peripheral clocks are off.
6 mA
HALT
Flash is powered down.
Peripheral clocks are off.
Input clock is disabled.
70 µA
6.4.1
IDDIO (1)
IDD
TEST CONDITIONS
Reducing Current Consumption
280x devices have a richer peripheral mix compared to the 281x family. While the McBSP has been
removed, the following new peripherals have been added on the 280x:
• 3 SPI modules
• 1 CAN module
• 1 I2C module
The two event manager modules of the 281x have been enhanced and replaced with separate ePWM (6),
eCAP (4) and eQEP (2) modules, providing tremendous flexibility in applications. Like 281x, 280x DSPs
incorporate a unique method to reduce the device current consumption. Since each peripheral unit has an
individual clock-enable bit, significant reduction in current consumption can be achieved by turning off the
clock to any peripheral module that is not used in a given application. Furthermore, any one of the three
low-power modes could be taken advantage of to reduce the current consumption even further. Table 6-4
indicates the typical reduction in current consumption achieved by turning off the clocks.
Table 6-4. Typical Current Consumption by Various
Peripherals (at 100 MHz) (1)
(1)
(2)
Submit Documentation Feedback
PERIPHERAL
MODULE
IDD CURRENT
REDUCTION (mA)
ADC
8 (2)
I2C
5
eQEP
5
ePWM
5
eCAP
2
SCI
4
SPI
5
eCAN
11
All peripheral clocks are disabled upon reset. Writing to/reading
from peripheral registers is possible only after the peripheral clocks
are turned on.
This number represents the current drawn by the digital portion of
the ADC module. Turning off the clock to the ADC module results in
the elimination of the current drawn by the analog portion of the
ADC (IDDA18) as well.
Electrical Specifications
83
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
NOTE
The baseline IDD current (current when the core is executing a dummy loop with no
peripherals enabled) is 110 mA, typical. To arrive at the IDD current for a given application,
the current-drawn by the peripherals (enabled by that application) must be added to the
baseline IDD current.
6.4.2
Current Consumption Graphs
250.0
Current (mA)
200.0
150.0
100.0
50.0
0.0
10
20
30
40
50
60
70
80
90
100
SYSCLKOUT (MHz)
IDD
IDDA18
1.8-V current
IDDIO
IDD3VFL
3.3-V current
Figure 6-2. Typical Operational Current Versus Frequency (F2808)
600.0
500.0
Device Power (mW)
400.0
300.0
200.0
100.0
0.0
10
20
30
40
50
60
70
80
90
100
SYSCLKOUT (MHz)
TOTAL POWER
Figure 6-3. Typical Operational Power Versus Frequency (F2808)
6.5
Timing Parameter Symbology
Timing parameter symbols used are created in accordance with JEDEC Standard 100. To shorten the
symbols, some of the pin names and other related terminology have been abbreviated as follows:
84
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.5.1
Lowercase subscripts and their
meanings:
Letters and symbols and their
meanings:
a
access time
H
High
c
cycle time (period)
L
Low
d
delay time
V
Valid
f
fall time
X
Unknown, changing, or don't
care level
h
hold time
Z
High impedance
r
rise time
su
setup time
t
transition time
v
valid time
w
pulse duration (width)
General Notes on Timing Parameters
All output signals from the 28x devices (including XCLKOUT) are derived from an internal clock such that
all output transitions for a given half-cycle occur with a minimum of skewing relative to each other.
The signal combinations shown in the following timing diagrams may not necessarily represent actual
cycles. For actual cycle examples, see the appropriate cycle description section of this document.
6.5.2
Test Load Circuit
This test load circuit is used to measure all switching characteristics provided in this document.
Tester Pin Electronics
42 Ω
Data Sheet Timing Reference Point
3.5 nH
Transmission Line
Z0 = 50 Ω(Α)
Output
Under
Test
Device Pin(B)
4.0 pF
1.85 pF
A.
Input requirements in this data sheet are tested with an input slew rate of < 4 Volts per nanosecond (4 V/ns) at the
device pin.
B.
The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its
transmission line effects must be taken into account. A transmission line with a delay of 2 ns or longer can be used to
produce the desired transmission line effect. The transmission line is intended as a load only. It is not necessary to
add or subtract the transmission line delay (2 ns or longer) from the data sheet timing.
Figure 6-4. 3.3-V Test Load Circuit
6.5.3
Device Clock Table
This section provides the timing requirements and switching characteristics for the various clock options
available on the 280x DSPs. Table 6-5 lists the cycle times of various clocks.
Submit Documentation Feedback
Electrical Specifications
85
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-5. TMS320x280x Clock Table and Nomenclature
MIN
On-chip oscillator
clock
XCLKIN (1)
SYSCLKOUT
XCLKOUT
HSPCLK (2)
LSPCLK (2)
ADC clock
(1)
(2)
(3)
tc(OSC), Cycle time
NOM
MAX
UNIT
28.6
50
ns
Frequency
20
35
MHz
tc(CI), Cycle time
10
250
ns
MHz
Frequency
4
100
10
500
ns
2
100
MHz
tc(XCO), Cycle time
10
2000
ns
Frequency
0.5
100
MHz
tc(HCO), Cycle time
10
tc(SCO), Cycle time
Frequency
20 (3)
ns
50 (3)
Frequency
tc(LCO), Cycle time
MHz
100
MHz
ns
25 (3)
Frequency
tc(ADCCLK), Cycle time
100
40 (3)
10
80
ns
Frequency
12.5
MHz
This also applies to the X1 pin if a 1.8-V oscillator is used.
Lower LSPCLK and HSPCLK will reduce device power consumption.
This is the default reset value if SYSCLKOUT = 100 MHz.
6.6
Clock Requirements and Characteristics
Table 6-6. Input Clock Frequency
PARAMETER
MIN
Resonator (X1/X2)
Crystal (X1/X2)
fx
Input clock frequency
fl
Limp mode clock frequency range
External oscillator/clock
source (XCLKIN or X1 pin)
TYP
20
MAX
UNIT
35
20
35
Without PLL
4
100
With PLL
5
MHz
30
1-5
MHz
Table 6-7. XCLKIN (1) Timing Requirements - PLL Enabled
NO.
MIN
MAX
UNIT
33.3
200
ns
6
ns
6
ns
55
%
C8
tc(CI)
Cycle time, XCLKIN
C9
tf(CI)
Fall time, XCLKIN
C10
tr(CI)
Rise time, XCLKIN
C11
tw(CIL)
Pulse duration, XCLKIN low as a percentage of tc(OSCCLK)
45
C12
tw(CIH)
Pulse duration, XCLKIN high as a percentage of tc(OSCCLK)
45
55
%
MIN
MAX
UNIT
10
250
ns
Up to 20 MHz
6
ns
20 MHz to 100 MHz
2
ns
Up to 20 MHz
6
ns
20 MHz to 100 MHz
2
ns
(1)
This applies to the X1 pin also.
Table 6-8. XCLKIN (1) Timing Requirements - PLL Disabled
NO.
C8
tc(CI)
Cycle time, XCLKIN
C9
tf(CI)
Fall time, XCLKIN
C10
tr(CI)
Rise time, XCLKIN
(1)
This applies to the X1 pin also.
86
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-8. XCLKIN Timing Requirements - PLL Disabled (continued)
MIN
MAX
C11
NO.
tw(CIL)
Pulse duration, XCLKIN low as a percentage of tc(OSCCLK)
45
55
UNIT
%
C12
tw(CIH)
Pulse duration, XCLKIN high as a percentage of tc(OSCCLK)
45
55
%
The possible configuration modes are shown in Table 3-15.
Table 6-9. XCLKOUT Switching Characteristics (PLL Bypassed or Enabled) (1) (2)
NO.
PARAMETER
MIN
TYP
C1
tc(XCO)
Cycle time, XCLKOUT
C3
tf(XCO)
Fall time, XCLKOUT
2
C4
tr(XCO)
Rise time, XCLKOUT
2
C5
tw(XCOL)
Pulse duration, XCLKOUT low
H-2
C6
tw(XCOH)
Pulse duration, XCLKOUT high
H-2
tp
PLL lock time
(1)
(2)
(3)
MAX
UNIT
10
ns
ns
ns
H+2
ns
H+2
ns
131072tc(OSCCLK) (3) cycles
A load of 40 pF is assumed for these parameters.
H = 0.5tc(XCO)
OSCCLK is either the output of the on-chip oscillator or the output from an external oscillator.
C10
C9
C8
XCLKIN(A)
C6
C3
C1
C4
C5
XCLKOUT(B)
A.
The relationship of XCLKIN to XCLKOUT depends on the divide factor chosen. The waveform relationship shown is
intended to illustrate the timing parameters only and may differ based on actual configuration.
B.
XCLKOUT configured to reflect SYSCLKOUT.
Figure 6-5. Clock Timing
6.7
Power Sequencing
No requirements are placed on the power up/down sequence of the various power pins to ensure the
correct reset state for all the modules. However, if the 3.3-V transistors in the level shifting output buffers
of the I/O pins are powered prior to the 1.8-V transistors, it is possible for the output buffers to turn on,
causing a glitch to occur on the pin during power up. To avoid this behavior, power the VDD pins prior to or
simultaneously with the VDDIO pins, ensuring that the VDD pins have reached 0.7 V before the VDDIO pins
reach 0.7 V.
There are some requirements on the XRS pin:
1. During power up, the XRS pin must be held low for tw(RSL1) after the input clock is stable (see
Table 6-11). This is to enable the entire device to start from a known condition.
2. During power down, the XRS pin must be pulled low at least 8 µs prior to VDD reaching 1.5 V. This is to
enhance flash reliability.
Additionally it is recommended that no voltage larger than a diode drop (0.7 V) should be applied to any
pin prior to powering up the device. Voltages applied to pins on an unpowered device can bias internal p-n
junctions in unintended ways and produce unpredictable results.
Submit Documentation Feedback
Electrical Specifications
87
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.7.1
Power Management and Supervisory Circuit Solutions
Table 6-10 lists the power management and supervisory circuit solutions for 280x DSPs. LDO selection
depends on the total power consumed in the end application. Go to www.power.ti.com for a complete list
of Texas Instruments power ICs or select Texas Instruments DSP Power Solutions for links to the DSP
Power Selection Guide (slub006a.pdf) and links to specific power reference designs.
Table 6-10. Power Management and Supervisory Circuit Solutions
SUPPLIER
TYPE
PART
Texas Instruments
LDO
TPS767D301
Texas Instruments
LDO
TPS70202
Dual 500/250-mA LDO with SVS
Texas Instruments
LDO
TPS766xx
250-mA LDO with PG
Texas Instruments
SVS
TPS3808
Open Drain SVS with programmable delay
Texas Instruments
SVS
TPS3803
Low-cost Open-drain SVS with 5 µS delay
Texas Instruments
LDO
TPS799xx
200-mA LDO in WCSP package
Texas Instruments
LDO
TPS736xx
400-mA LDO with 40 mV of VDO
Texas Instruments
DC/DC
TPS62110
High Vin 1.2-A dc/dc converter in 4x4 QFN package
Texas Instruments
DC/DC
TPS6230x
500-mA converter in WCSP package
88
Electrical Specifications
DESCRIPTION
Dual 1-A low-dropout regulator (LDO) with supply voltage supervisor (SVS)
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
VDDIO, VDD3VFL
VDDA2, VDDAIO
(3.3 V)
VDD, VDD1A18,
VDD2A18
(1.8 V)
XCLKIN
X1/X2
OSCCLK/8(A)
XCLKOUT
tOSCST
User-Code Dependent
tw(RSL1)
XRS
Address/Data Valid. Internal Boot-ROM Code Execution Phase
Address/Data/
Control
(Internal)
td(EX)
th(boot-mode)(B)
Boot-Mode
Pins
User-Code Execution Phase
User-Code Dependent
GPIO Pins as Input
Peripheral/GPIO Function
Based on Boot Code
Boot-ROM Execution Starts
I/O Pins(C)
GPIO Pins as Input (State Depends on Internal PU/PD)
User-Code Dependent
A.
Upon power up, SYSCLKOUT is OSCCLK/2. Since the XCLKOUTDIV bits in the XCLK register come up with a reset
state of 0, SYSCLKOUT is further divided by 4 before it appears at XCLKOUT. This explains why XCLKOUT =
OSCCLK/8 during this phase.
B.
After reset, the boot ROM code samples Boot Mode pins. Based on the status of the Boot Mode pin, the boot code
branches to destination memory or boot code function. If boot ROM code executes after power-on conditions (in
debugger environment), the boot code execution time is based on the current SYSCLKOUT speed. The SYSCLKOUT
will be based on user environment and could be with or without PLL enabled.
Figure 6-6. Power-on Reset
Submit Documentation Feedback
Electrical Specifications
89
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-11. Reset (XRS) Timing Requirements
MIN
tw(RSL1)
(1)
Pulse duration, stable XCLKIN to XRS high
tw(RSL2)
Pulse duration, XRS low
tw(WDRS)
Pulse duration, reset pulse generated by
watchdog
td(EX)
Delay time, address/data valid after XRS high
tOSCST (2)
Oscillator start-up time
th(boot-mode)
Hold time for boot-mode pins
(1)
(2)
Warm reset
NOM
MAX
UNIT
8tc(OSCCLK)
cycles
8tc(OSCCLK)
cycles
512tc(OSCCLK)
cycles
32tc(OSCCLK)
cycles
1
10
200tc(OSCCLK)
ms
cycles
In addition to the tw(RSL1) requirement, XRS has to be low at least for 1 ms after VDD reaches 1.5 V.
Dependent on crystal/resonator and board design.
XCLKIN
X1/X2
OSCCLK/8
XCLKOUT
User-Code Dependent
OSCCLK * 5
tw(RSL2)
XRS
Address/Data/
Control
(Internal)
td(EX)
User-Code Execution
(Don’t Care)
Boot-ROM Execution Starts
Boot-Mode
Pins
Peripheral/GPIO Function
User-Code Execution Phase
GPIO Pins as Input
th(boot-mode)(A)
Peripheral/GPIO Function
User-Code Execution Starts
I/O Pins
User-Code Dependent
GPIO Pins as Input (State Depends on Internal PU/PD)
User-Code Dependent
A.
After reset, the Boot ROM code samples BOOT Mode pins. Based on the status of the Boot Mode pin, the boot code
branches to destination memory or boot code function. If Boot ROM code executes after power-on conditions (in
debugger environment), the Boot code execution time is based on the current SYSCLKOUT speed. The
SYSCLKOUT will be based on user environment and could be with or without PLL enabled.
Figure 6-7. Warm Reset
Figure 6-8 shows an example for the effect of writing into PLLCR register. In the first phase, PLLCR =
0x0004 and SYSCLKOUT = OSCCLK x 2. The PLLCR is then written with 0x0008. Right after the PLLCR
register is written, the PLL lock-up phase begins. During this phase, SYSCLKOUT = OSCCLK/2. After the
PLL lock-up is complete (which takes 131072 OSCCLK cycles), SYSCLKOUT reflects the new operating
frequency, OSCCLK x 4.
90
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
OSCCLK
Write to PLLCR
SYSCLKOUT
OSCCLK * 2
OSCCLK/2
OSCCLK * 4
(Current CPU
Frequency)
(CPU Frequency While PLL is Stabilizing
With the Desired Frequency. This Period
(PLL Lock-up Time, tp) is
131072 OSCCLK Cycles Long.)
(Changed CPU Frequency)
Figure 6-8. Example of Effect of Writing Into PLLCR Register
6.8
6.8.1
General-Purpose Input/Output (GPIO)
GPIO - Output Timing
Table 6-12. General-Purpose Output Switching Characteristics
PARAMETER
MIN
MAX
UNIT
tr(GPO)
Rise time, GPIO switching low to high
All GPIOs
8
tf(GPO)
Fall time, GPIO switching high to low
All GPIOs
8
ns
ns
tfGPO
Toggling frequency, GPO pins
25
MHz
GPIO
tf(GPO)
tr(GPO)
Figure 6-9. General-Purpose Output Timing
Submit Documentation Feedback
Electrical Specifications
91
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.8.2
GPIO - Input Timing
(A)
GPIO Signal
GPxQSELn = 1,0 (6 samples)
1
1
0
0
0
0
0
0
0
1
0
tw(SP)
0
0
1
1
1
1
1
1
1
1
1
Sampling Period determined
by GPxCTRL[QUALPRD](B)
tw(IQSW)
(SYSCLKOUT cycle * 2 * QUALPRD) * 5(C))
Sampling Window
SYSCLKOUT
QUALPRD = 1
(SYSCLKOUT/2)
(D)
Output From
Qualifier
A.
This glitch will be ignored by the input qualifier. The QUALPRD bit field specifies the qualification sampling period. It
can vary from 00 to 0xFF. If QUALPRD = 00, then the sampling period is 1 SYSCLKOUT cycle. For any other value
"n", the qualification sampling period in 2n SYSCLKOUT cycles (i.e., at every 2n SYSCLKOUT cycles, the GPIO pin
will be sampled)..
B.
The qualification period selected via the GPxCTRL register applies to groups of 8 GPIO pins.
C.
The qualification block can take either three or six samples. The GPxQSELn Register selects which sample mode is
used.
D.
In the example shown, for the qualifier to detect the change, the input should be stable for 10 SYSCLKOUT cycles or
greater. In other words, the inputs should be stable for (5 x QUALPRD x 2) SYSCLKOUT cycles. This would ensure 5
sampling periods for detection to occur. Since external signals are driven asynchronously, an 13-SYSCLKOUT-wide
pulse ensures reliable recognition.
Figure 6-10. Sampling Mode
Table 6-13. General-Purpose Input Timing Requirements
MIN
tw(SP)
Sampling period
tw(IQSW)
Input qualifier sampling window
tw(GPI) (2)
(1)
(2)
Pulse duration, GPIO low/high
MAX
UNIT
QUALPRD = 0
1tc(SCO)
cycles
QUALPRD ≠ 0
2tc(SCO) * QUALPRD
cycles
tw(SP) * (n (1) - 1)
cycles
2tc(SCO)
cycles
tw(IQSW) + tw(SP) + 1tc(SCO)
cycles
Synchronous mode
With input qualifier
"n" represents the number of qualification samples as defined by GPxQSELn register.
For tw(GPI), pulse width is measured from VIL to VIL for an active low signal and VIH to VIH for an active high signal.
6.8.3
Sampling Window Width for Input Signals
The following section summarizes the sampling window width for input signals for various input qualifier
configurations.
Sampling frequency denotes how often a signal is sampled with respect to SYSCLKOUT.
Sampling frequency = SYSCLKOUT/(2 * QUALPRD), if QUALPRD ≠ 0
Sampling frequency = SYSCLKOUT, if QUALPRD = 0
Sampling period = SYSCLKOUT cycle x 2 x QUALPRD, if QUALPRD ≠ 0
In the above equations, SYSCLKOUT cycle indicates the time period of SYSCLKOUT.
Sampling period = SYSCLKOUT cycle, if QUALPRD = 0
92
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
In a given sampling window, either 3 or 6 samples of the input signal are taken to determine the validity of
the signal. This is determined by the value written to GPxQSELn register.
Case 1:
Qualification using 3 samples
Sampling window width = (SYSCLKOUT cycle x 2 x QUALPRD) x 2, if QUALPRD ≠ 0
Sampling window width = (SYSCLKOUT cycle) x 2, if QUALPRD = 0
Case 2:
Qualification using 6 samples
Sampling window width = (SYSCLKOUT cycle x 2 x QUALPRD) x 5, if QUALPRD ≠ 0
Sampling window width = (SYSCLKOUT cycle) x 5, if QUALPRD = 0
XCLKOUT
GPIOxn
tw(GPI)
Figure 6-11. General-Purpose Input Timing
The pulse-width requirement
XINT2_ADCSOC signal as well.
Submit Documentation Feedback
for
NOTE
general-purpose
input
is
applicable
for
the
Electrical Specifications
93
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.8.4
Low-Power Mode Wakeup Timing
Table 6-14 shows the timing requirements, Table 6-15 shows the switching characteristics, and
Figure 6-12 shows the timing diagram for IDLE mode.
Table 6-14. IDLE Mode Timing Requirements (1)
MIN
tw(WAKE-INT)
(1)
Pulse duration, external wake-up signal
Without input qualifier
NOM
MAX
2tc(SCO)
With input qualifier
UNIT
cycles
5tc(SCO) + tw(IQSW)
For an explanation of the input qualifier parameters, see Table 6-13.
Table 6-15. IDLE Mode Switching Characteristics (1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
20tc(SCO)
cycles
Delay time, external wake signal to
program execution resume (2)
•
td(WAKE-IDLE)
•
•
Wake-up from Flash
– Flash module in active state
Without input qualifier
Wake-up from Flash
– Flash module in sleep state
Without input qualifier
Wake-up from SARAM
Without input qualifier
With input qualifier
20tc(SCO) + tw(IQSW)
1050tc(SCO)
With input qualifier
20tc(SCO)
With input qualifier
(1)
(2)
cycles
1050tc(SCO) + tw(IQSW)
cycles
20tc(SCO) + tw(IQSW)
For an explanation of the input qualifier parameters, see Table 6-13.
This is the time taken to begin execution of the instruction that immediately follows the IDLE instruction. execution of an ISR (triggered
by the wake up) signal involves additional latency.
td(WAKE−IDLE)
Addres/Data
(internal)
XCLKOUT
tw(WAKE−INT)
WAKE
A.
INT(A)
WAKE INT can be any enabled interrupt, WDINT, XNMI, or XRS.
Figure 6-12. IDLE Entry and Exit Timing
Table 6-16. STANDBY Mode Timing Requirements
TEST CONDITIONS
tw(WAKEINT)
(1)
94
Pulse duration, external
wake-up signal
Without input qualification
With input qualification (1)
MIN
3tc(OSCCLK)
(2 + QUALSTDBY) * tc(OSCCLK)
NOM
MAX
UNIT
cycles
QUALSTDBY is a 6-bit field in the LPMCR0 register.
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-17. STANDBY Mode Switching Characteristics
PARAMETER
TEST CONDITIONS
Delay time, IDLE instruction
executed to XCLKOUT low
td(IDLE-XCOL)
MIN
TYP
32tc(SCO)
MAX
UNIT
45tc(SCO)
cycles
Delay time, external wake signal
to program execution resume (1)
•
td(WAKE-STBY)
•
Wake up from flash
– Flash module in active
state
Without input qualifier
Wake up from flash
– Flash module in sleep
state
Without input qualifier
100tc(SCO)
With input qualifier
100tc(SCO) + tw(WAKE-INT)
With input qualifier
Wake up from SARAM
cycles
1125tc(SCO)
1125tc(SCO) + tw(WAKE-INT)
Without input qualifier
•
(1)
cycles
100tc(SCO)
With input qualifier
100tc(SCO) + tw(WAKE-INT)
cycles
cycles
This is the time taken to begin execution of the instruction that immediately follows the IDLE instruction. execution of an ISR (triggered
by the wake up signal) involves additional latency.
(A)
(C)
(B)
Device
Status
STANDBY
(E)
(D)
(F)
STANDBY
Normal Execution
Flushing Pipeline
Wake−up
Signal
tw(WAKE-INT)
td(WAKE-STBY)
X1/X2 or
X1 or
XCLKIN
XCLKOUT
td(IDLE−XCOL)
A.
IDLE instruction is executed to put the device into STANDBY mode.
B.
The PLL block responds to the STANDBY signal. SYSCLKOUT is held for approximately 32 cycles before being
turned off. This 32-cycle delay enables the CPU pipe and any other pending operations to flush properly.
C.
Clock to the peripherals are turned off. However, the PLL and watchdog are not shut down. The device is now in
STANDBY mode.
D.
The external wake-up signal is driven active.
E.
After a latency period, the STANDBY mode is exited.
F.
Normal execution resumes. The device will respond to the interrupt (if enabled).
Figure 6-13. STANDBY Entry and Exit Timing Diagram
Table 6-18. HALT Mode Timing Requirements
MIN
tw(WAKE-GPIO)
Pulse duration, GPIO wake-up signal
tw(WAKE-XRS)
Pulse duration, XRS wakeup signal
(1)
NOM
MAX
UNIT
toscst + 2tc(OSCCLK) (1)
cycles
toscst + 8tc(OSCCLK)
cycles
See Table 6-11 for an explanation of toscst.
Submit Documentation Feedback
Electrical Specifications
95
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-19. HALT Mode Switching Characteristics
PARAMETER
MIN
td(IDLE-XCOL)
Delay time, IDLE instruction executed to XCLKOUT low
tp
PLL lock-up time
td(WAKE-HALT)
Delay time, PLL lock to program execution resume
• Wake up from flash
– Flash module in sleep state
•
TYP
32tc(SCO)
(C)
45tc(SCO)
cycles
cycles
1125tc(SCO)
cycles
35tc(SCO)
cycles
(G)
(E)
(B)
Device
Status
(D)
HALT
Flushing Pipeline
UNIT
131072tc(OSCCLK)
Wake up from SARAM
(A)
MAX
(F)
HALT
PLL Lock-up Time
Wake-up Latency
Normal
Execution
GPIOn
td(WAKE−HALT)
tw(WAKE-GPIO)
tp
X1/X2
or XCLKIN
Oscillator Start-up Time
XCLKOUT
td(IDLE−XCOL)
A.
IDLE instruction is executed to put the device into HALT mode.
B.
The PLL block responds to the HALT signal. SYSCLKOUT is held for approximately 32 cycles before the oscillator is
turned off and the CLKIN to the core is stopped. This 32-cycle delay enables the CPU pipe and any other pending
operations to flush properly.
C.
Clocks to the peripherals are turned off and the PLL is shut down. If a quartz crystal or ceramic resonator is used as
the clock source, the internal oscillator is shut down as well. The device is now in HALT mode and consumes
absolute minimum power.
D.
When the GPIOn pin is driven low, the oscillator is turned on and the oscillator wake-up sequence is initiated. The
GPIO pin should be driven high only after the oscillator has stabilized. This enables the provision of a clean clock
signal during the PLL lock sequence. Since the falling edge of the GPIO pin asynchronously begins the wakeup
procedure, care should be taken to maintain a low noise environment prior to entering and during HALT mode.
E.
When GPIOn is deactivated, it initiates the PLL lock sequence, which takes 131,072 OSCCLK (X1/X2 or X1 or
XCLKIN) cycles.
F.
When CLKIN to the core is enabled, the device will respond to the interrupt (if enabled), after a latency. The HALT
mode is now exited.
G.
Normal operation resumes.
Figure 6-14. HALT Wake Up Using GPIOn
6.9
6.9.1
Enhanced Control Peripherals
Enhanced Pulse Width Modulator (ePWM) Timing
PWM refers to PWM outputs on ePWM1-6. Table 6-20 shows the PWM timing requirements and
Table 6-21, switching characteristics.
96
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-20. ePWM Timing Requirements (1)
TEST CONDITIONS
tw(SYCIN)
Sync input pulse width
MIN
UNIT
Asynchronous
2tc(SCO)
cycles
Synchronous
2tc(SCO)
cycles
1tc(SCO) + tw(IQSW)
cycles
With input qualifier
(1)
MAX
For an explanation of the input qualifier parameters, see Table 6-13.
Table 6-21. ePWM Switching Characteristics
PARAMETER
tw(PWM)
Pulse duration, PWMx output high/low
tw(SYNCOUT)
Sync output pulse width
td(PWM)tza
Delay time, trip input active to PWM forced high
Delay time, trip input active to PWM forced low
td(TZ-PWM)HZ
Delay time, trip input active to PWM Hi-Z
6.9.2
TEST CONDITIONS
MIN
MAX
UNIT
20
ns
8tc(SCO)
cycles
no pin load
25
ns
20
ns
Trip-Zone Input Timing
XCLKOUT(A)
tw(TZ)
TZ
td(TZ-PWM)HZ
PWM(B)
A.
TZ - TZ1, TZ2, TZ3, TZ4, TZ5, TZ6
B.
PWM refers to all the PWM pins in the device. The state of the PWM pins after TZ is taken high depends on the PWM
recovery software.
Figure 6-15. PWM Hi-Z Characteristics
Table 6-22. Trip-Zone input Timing Requirements (1)
MIN
tw(TZ)
Pulse duration, TZx input low
Asynchronous
Synchronous
With input qualifier
(1)
MAX
UNIT
1tc(SCO)
cycles
2tc(SCO)
cycles
1tc(SCO) + tw(IQSW)
cycles
For an explanation of the input qualifier parameters, see Table 6-13.
Table 6-23 shows the high-resolution PWM switching characteristics.
Submit Documentation Feedback
Electrical Specifications
97
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-23. High Resolution PWM Characteristics at SYSCLKOUT = (60 - 100 MHz)
MIN
TYP
MAX
UNIT
150
310
ps
Micro Edge Positioning (MEP) step size (1)
(1)
Maximum MEP step size is based on worst-case process, maximum temperature and maximum voltage. MEP step size will increase
with low voltage and high temperature and decrease with voltage and cold temperature.
Applications that use the HRPWM feature should use MEP Scale Factor Optimizer (SFO) estimation software functions. See the Texas
Instruments software libraries for details of using SFO function in end applications. SFO functions help to estimate the number of MEP
steps per SYSCLKOUT period dynamically while the HRPWM is in operation.
Table 6-24 shows the eCAP timing requirement and Table 6-25 shows the eCAP switching characteristics.
Table 6-24. Enhanced Capture (eCAP) Timing Requirement (1)
TEST CONDITIONS
tw(CAP)
Capture input pulse width
MIN
UNIT
Asynchronous
2tc(SCO)
cycles
Synchronous
2tc(SCO)
cycles
1tc(SCO) + tw(IQSW)
cycles
With input qualifier
(1)
MAX
For an explanation of the input qualifier parameters, see Table 6-13.
Table 6-25. eCAP Switching Characteristics
PARAMETER
tw(APWM)
TEST CONDITIONS
MIN
Pulse duration, APWMx output high/low
MAX
20
UNIT
ns
Table 6-26 shows the eQEP timing requirement and Table 6-27 shows the eQEP switching
characteristics.
Table 6-26. Enhanced Quadrature Encoder Pulse (eQEP) Timing Requirements (1)
TEST CONDITIONS
tw(QEPP)
QEP input period
tw(INDEXH)
QEP Index Input High time
With input qualifier
QEP Index Input Low time
tw(STROBH)
QEP Strobe High time
tw(STROBL)
QEP Strobe Input Low time
cycles
2tc(SCO)
cycles
2tc(SCO) +tw(IQSW)
cycles
2tc(SCO)
cycles
2tc(SCO) + tw(IQSW)
cycles
2tc(SCO)
cycles
2tc(SCO) + tw(IQSW)
cycles
2tc(SCO)
cycles
2tc(SCO) +tw(IQSW)
cycles
Asynchronous/synchronous
With input qualifier
(1)
2(1tc(SCO) + tw(IQSW))
Asynchronous/synchronous
With input qualifier
UNIT
cycles
Asynchronous/synchronous
With input qualifier
MAX
2tc(SCO)
Asynchronous/synchronous
With input qualifier
tw(INDEXL)
MIN
Asynchronous/synchronous
For an explanation of the input qualifier parameters, see Table 6-13.
Table 6-27. eQEP Switching Characteristics
MAX
UNIT
td(CNTR)xin
Delay time, external clock to counter increment
PARAMETER
TEST CONDITIONS
MIN
4tc(SCO)
cycles
td(PXCSOUT)QEP
Delay time, QEP input edge to position compare sync output
6tc(SCO)
cycles
Table 6-28. External ADC Start-of-Conversion Switching Characteristics
PARAMETER
tw(ADCSOCAL)
98
Pulse duration, ADCSOCAO low
Electrical Specifications
MIN
32tc(HCO)
MAX
UNIT
cycles
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
tw(ADCSOCAL)
ADCSOCAO
or
ADCSOCBO
Figure 6-16. ADCSOCAO or ADCSOCBO Timing
6.9.3
External Interrupt Timing
tw(INT)
XNMI, XINT1, XINT2
td(INT)
Address bus
(internal)
Interrupt Vector
Figure 6-17. External Interrupt Timing
Table 6-29. External Interrupt Timing Requirements (1)
TEST CONDITIONS
tw(INT)
(1)
Pulse duration, INT input low/high
MIN
MAX
UNIT
Synchronous
1tc(SCO)
cycles
With qualifier
1tc(SCO) + tw(IQSW)
cycles
For an explanation of the input qualifier parameters, see Table 6-13.
Table 6-30. External Interrupt Switching Characteristics (1)
PARAMETER
td(INT)
(1)
Delay time, INT low/high to interrupt-vector fetch
MIN
MAX
UNIT
tw(IQSW) + 12tc(SCO)
cycles
For an explanation of the input qualifier parameters, see Table 6-13.
Submit Documentation Feedback
Electrical Specifications
99
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.9.4
I2C Electrical Specification and Timing
Table 6-31. I2C Timing
TEST CONDITIONS
MIN
UNIT
400
kHz
SCL clock frequency
vil
Low level input voltage
Vih
High level input voltage
Vhys
Input hysteresis
Vol
Low level output voltage
3 mA sink current
tLOW
Low period of SCL clock
I2C clock module frequency is between 7
MHz and 12 MHz and I2C prescaler and
clock divider registers are configured
appropriately
1.3
µs
tHIGH
High period of SCL clock
I2C clock module frequency is between 7
MHz and 12 MHz and I2C prescaler and
clock divider registers are configured
appropriately
0.6
µs
lI
Input current with an input voltage
between 0.1 VDDIO and 0.9 VDDIO MAX
6.9.5
I2C clock module frequency is between 7
MHz and 12 MHz and I2C prescaler and
clock divider registers are configured
appropriately
MAX
fSCL
0.3 VDDIO
0.7 VDDIO
V
0.05 VDDIO
0
-10
V
V
0.4
10
V
µA
Serial Peripheral Interface (SPI) Master Mode Timing
Table 6-32 lists the master mode timing (clock phase = 0) and Table 6-33 lists the timing (clock phase =
1). Figure 6-18 and Figure 6-19 show the timing waveforms.
100
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-32. SPI Master Mode External Timing (Clock Phase = 0)
NO.
SPI WHEN (SPIBRR + 1) IS EVEN OR
SPIBRR = 0 OR 2
MIN
MAX
MIN
UNIT
MAX
tc(SPC)M
Cycle time, SPICLK
4tc(LCO)
128tc(LCO)
5tc(LCO)
127tc(LCO)
ns
2
tw(SPCH)M
Pulse duration, SPICLK high
(clock polarity = 0)
0.5tc(SPC)M -10
0.5tc(SPC)M
0.5tc(SPC)M - 0.5tc(LCO) - 10
0.5tc(SPC)M - 0.5tc(LCO)
ns
tw(SPCL)M
Pulse duration, SPICLK low
(clock polarity = 1)
0.5tc(SPC)M - 10
0.5tc(SPC)M
0.5tc(SPC)M - 0.5tc(LCO) - 10
0.5tc(SPC)M - 0.5tc(LCO)
tw(SPCL)M
Pulse duration, SPICLK low
(clock polarity = 0)
0.5tc(SPC)M - 10
0.5tc(SPC)M
0.5tc(SPC)M + 0.5tc(LCO)-10
0.5tc(SPC)M + 0.5tc(LCO)
tw(SPCH)M
Pulse duration, SPICLK high
(clock polarity = 1)
0.5tc(SPC)M - 10
0.5tc(SPC)M
0.5tc(SPC)M + 0.5tc(LCO)- 10
0.5tc(SPC)M + 0.5tc(LCO)
td(SPCH-SIMO)M
Delay time, SPICLK high to SPISIMO
valid (clock polarity = 0)
10
10
td(SPCL-SIMO)M
Delay time, SPICLK low to SPISIMO
valid (clock polarity = 1)
10
10
tv(SPCL-SIMO)M
Valid time, SPISIMO data valid after
SPICLK low (clock polarity = 0)
0.5tc(SPC)M -10
0.5tc(SPC)M + 0.5tc(LCO) -10
tv(SPCH-SIMO)M
Valid time, SPISIMO data valid after
SPICLK high (clock polarity = 1)
0.5tc(SPC)M -10
0.5tc(SPC)M + 0.5tc(LCO) -10
tsu(SOMI-SPCL)M
Setup time, SPISOMI before SPICLK
low (clock polarity = 0)
35
35
ns
tsu(SOMI-SPCH)M
Setup time, SPISOMI before SPICLK
high (clock polarity = 1)
35
35
ns
tv(SPCL-SOMI)M
Valid time, SPISOMI data valid after
SPICLK low (clock polarity = 0)
0.25tc(SPC)M -10
0.5tc(SPC)M- 0.5tc(LCO)- 10
tv(SPCH-SOMI)M
Valid time, SPISOMI data valid after
SPICLK high (clock polarity = 1)
0.25tc(SPC)M - 10
0.5tc(SPC)M- 0.5tc(LCO)- 10
4
5
8
9
(5)
SPI WHEN (SPIBRR + 1) IS ODD
AND SPIBRR > 3
1
3
(1)
(2)
(3)
(4)
(1) (2) (3) (4) (5)
ns
ns
ns
The MASTER / SLAVE bit (SPICTL.2) is set and the CLOCK PHASE bit (SPICTL.3) is cleared.
tc(SPC) = SPI clock cycle time = LSPCLK/4 or LSPCLK/(SPIBRR +1)
tc(LCO) = LSPCLK cycle time
Internal clock prescalers must be adjusted such that the SPI clock speed is limited to the following SPI clock rate:
Master mode transmit 25-MHz MAX, master mode receive 12.5-MHz MAX
Slave mode transmit 12.5-MAX, slave mode receive 12.5-MHz MAX.
The active edge of the SPICLK signal referenced is controlled by the clock polarity bit (SPICCR.6).
Submit Documentation Feedback
Electrical Specifications
101
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
1
SPICLK
(clock polarity = 0)
2
3
SPICLK
(clock polarity = 1)
4
5
SPISIMO
Master Out Data Is Valid
8
9
SPISOMI
Master In Data
Must Be Valid
SPISTE(A)
A.
In the master mode, SPISTE goes active 0.5tc(SPC) (minimum) before valid SPI clock edge. On the trailing end of the
word, the SPISTE will go inactive 0.5tc(SPC) after the receiving edge (SPICLK) of the last data bit.
Figure 6-18. SPI Master Mode External Timing (Clock Phase = 0)
102
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-33. SPI Master Mode External Timing (Clock Phase = 1)
NO.
SPI WHEN (SPIBRR + 1) IS EVEN
OR SPIBRR = 0 OR 2
MIN
MIN
UNIT
MAX
tc(SPC)M
Cycle time, SPICLK
4tc(LCO)
128tc(LCO)
5tc(LCO)
127tc(LCO)
ns
2
tw(SPCH)M
Pulse duration, SPICLK high (clock
polarity = 0)
0.5tc(SPC)M -10
0.5tc(SPC)M
0.5tc(SPC)M - 0.5tc (LCO)-10
0.5tc(SPC)M - 0.5tc(LCO)
ns
tw(SPCL))M
Pulse duration, SPICLK low (clock
polarity = 1)
0.5tc(SPC)M -10
0.5tc(SPC)M
0.5tc(SPC)M - 0.5tc (LCO)-10
0.5tc(SPC)M - 0.5tc(LCO
ns
tw(SPCL)M
Pulse duration, SPICLK low (clock
polarity = 0)
0.5tc(SPC)M -10
0.5tc(SPC)M
0.5tc(SPC)M + 0.5tc(LCO) - 10
0.5tc(SPC)M + 0.5tc(LCO)
ns
tw(SPCH)M
Pulse duration, SPICLK high (clock
polarity = 1)
0.5tc(SPC)M -10
0.5tc(SPC)M
0.5tc(SPC)M + 0.5tc(LCO) -10
0.5tc(SPC)M + 0.5tc(LCO)
ns
tsu(SIMO-SPCH)M
Setup time, SPISIMO data valid
before SPICLK high (clock polarity
= 0)
0.5tc(SPC)M -10
0.5tc(SPC)M - 10
ns
tsu(SIMO-SPCL)M
Setup time, SPISIMO data valid
before SPICLK low (clock polarity =
1)
0.5tc(SPC)M -10
0.5tc(SPC)M - 10
ns
tv(SPCH-SIMO)M
Valid time, SPISIMO data valid after
SPICLK high (clock polarity = 0)
0.5tc(SPC)M -10
0.5tc(SPC)M - 10
ns
tv(SPCL-SIMO)M
Valid time, SPISIMO data valid after
SPICLK low (clock polarity = 1)
0.5tc(SPC)M -10
0.5tc(SPC)M -10
ns
tsu(SOMI-SPCH)M
Setup time, SPISOMI before
SPICLK high (clock polarity = 0)
35
35
ns
tsu(SOMI-SPCL)M
Setup time, SPISOMI before
SPICLK low (clock polarity = 1)
35
35
ns
tv(SPCH-SOMI)M
Valid time, SPISOMI data valid after
SPICLK high (clock polarity = 0)
0.25tc(SPC)M -10
0.5tc(SPC)M -10
ns
tv(SPCL-SOMI)M
Valid time, SPISOMI data valid after
SPICLK low (clock polarity = 1)
0.25tc(SPC)M -10
0.5tc(SPC)M -10
ns
6
7
10
11
(4)
(5)
SPI WHEN (SPIBRR + 1) IS ODD
AND SPIBRR > 3
1
3
(1)
(2)
(3)
MAX
(1) (2) (3) (4) (5)
The MASTER/SLAVE bit (SPICTL.2) is set and the CLOCK PHASE bit (SPICTL.3) is set.
tc(SPC) = SPI clock cycle time = LSPCLK/4 or LSPCLK/(SPIBRR + 1)
Internal clock prescalers must be adjusted such that the SPI clock speed is limited to the following SPI clock rate:
Master mode transmit 25 MHz MAX, master mode receive 12.5 MHz MAX
Slave mode transmit 12.5 MHz MAX, slave mode receive 12.5 MHz MAX.
tc(LCO) = LSPCLK cycle time
The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).
Submit Documentation Feedback
Electrical Specifications
103
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
1
SPICLK
(clock polarity = 0)
2
3
SPICLK
(clock polarity = 1)
6
7
SPISIMO
Master Out Data Is Valid
Data Valid
10
11
Master In Data Must
Be Valid
SPISOMI
SPISTE(A)
A.
In the master mode, SPISTE goes active 0.5tc(SPC) (minimum) before valid SPI clock edge. On the trailing end of the
word, the SPISTE will go inactive 0.5tc(SPC) after the receiving edge (SPICLK) of the last data bit.
Figure 6-19. SPI Master External Timing (Clock Phase = 1)
6.9.6
SPI Slave Mode Timing
Table 6-34 lists the slave mode external timing (clock phase = 0) and Table 6-35 (clock phase = 1).
Figure 6-20 and Figure 6-21 show the timing waveforms.
Table 6-34. SPI Slave Mode External Timing (Clock Phase = 0) (1) (2) (3) (4) (5)
NO.
MIN
MAX
12
tc(SPC)S
Cycle time, SPICLKCycle time, SPICLK
13
tw(SPCH)S
Pulse duration, SPICLK high (clock polarity = 0)
0.5tc(SPC)S - 10
0.5tc(SPC)S
ns
tw(SPCL)S
Pulse duration, SPICLK low (clock polarity = 1)
0.5tc(SPC)S - 10
0.5tc(SPC)S
ns
tw(SPCL)S
Pulse duration, SPICLK low (clock polarity = 0)
0.5tc(SPC)S - 10
0.5tc(SPC)S
ns
tw(SPCH)S
Pulse duration, SPICLK high (clock polarity = 1)
0.5tc(SPC)S - 10
0.5tc(SPC)S
ns
td(SPCH-SOMI)S
Delay time, SPICLK high to SPISOMI valid (clock polarity = 0)
35
ns
td(SPCL-SOMI)S
Delay time, SPICLK low to SPISOMI valid (clock polarity = 1)
35
ns
tv(SPCL-SOMI)S
Valid time, SPISOMI data valid after SPICLK low (clock polarity = 0)
0.75tc(SPC)S
ns
tv(SPCH-SOMI)S
Valid time, SPISOMI data valid after SPICLK high (clock polarity = 1)
0.75tc(SPC)S
ns
tsu(SIMO-SPCL)S
Setup time, SPISIMO before SPICLK low (clock polarity = 0)
35
ns
tsu(SIMO-SPCH)S
Setup time, SPISIMO before SPICLK high (clock polarity = 1)
35
ns
tv(SPCL-SIMO)S
Valid time, SPISIMO data valid after SPICLK low (clock polarity = 0)
0.5tc(SPC)S
ns
tv(SPCH-SIMO)S
Valid time, SPISIMO data valid after SPICLK high (clock polarity = 1)
0.5tc(SPC)S
ns
14
15
16
19
20
(1)
(2)
(3)
(4)
(5)
104
4tc(LCO)
UNIT
ns
The MASTER / SLAVE bit (SPICTL.2) is cleared and the CLOCK PHASE bit (SPICTL.3) is cleared.
tc(SPC) = SPI clock cycle time = LSPCLK/4 or LSPCLK/(SPIBRR + 1)
Internal clock prescalers must be adjusted such that the SPI clock speed is limited to the following SPI clock rate:
Master mode transmit 25-MHz MAX, master mode receive 12.5-MHz MAX
Slave mode transmit 12.5-MHz MAX, slave mode receive 12.5-MHz MAX.
tc(LCO) = LSPCLK cycle time
The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
12
SPICLK
(clock polarity = 0)
13
14
SPICLK
(clock polarity = 1)
15
16
SPISOMI
SPISOMI Data Is Valid
19
20
SPISIMO
SPISIMO Data
Must Be Valid
SPISTE(A)
A.
In the slave mode, the SPISTE signal should be asserted low at least 0.5tc(SPC) (minimum) before the valid SPI clock
edge and remain low for at least 0.5tc(SPC) after the receiving edge (SPICLK) of the last data bit.
Figure 6-20. SPI Slave Mode External Timing (Clock Phase = 0)
Table 6-35. SPI Slave Mode External Timing (Clock Phase = 1) (1) (2) (3) (4)
NO.
tc(SPC)S
Cycle time, SPICLK
tw(SPCH)S
Pulse duration, SPICLK high (clock polarity = 0)
0.5tc(SPC)S - 10
0.5tc(SPC)S
ns
tw(SPCL)S
Pulse duration, SPICLK low (clock polarity = 1)
0.5tc(SPC)S - 10
0.5tc(SPC)S
ns
tw(SPCL)S
Pulse duration, SPICLK low (clock polarity = 0)
0.5tc(SPC)S - 10
0.5tc(SPC)S
ns
tw(SPCH)S
Pulse duration, SPICLK high (clock polarity = 1)
0.5tc(SPC)S - 10
0.5tc(SPC)S
ns
tsu(SOMI-SPCH)S
Setup time, SPISOMI before SPICLK high (clock polarity = 0)
0.125tc(SPC)S
ns
tsu(SOMI-SPCL)S
Setup time, SPISOMI before SPICLK low (clock polarity = 1
0.125tc(SPC)S
ns
tv(SPCH-SOMI)S
Valid time, SPISOMI data valid after SPICLK low (clock polarity = 0)
0.75tc(SPC)S
ns
tv(SPCL-SOMI)S
Valid time, SPISOMI data valid after SPICLK high (clock polarity =
1)
0.75tc(SPC)S
ns
tsu(SIMO-SPCH)S
Setup time, SPISIMO before SPICLK high (clock polarity = 0)
35
ns
tsu(SIMO-SPCL)S
Setup time, SPISIMO before SPICLK low (clock polarity = 1)
35
ns
tv(SPCH-SIMO)S
Valid time, SPISIMO data valid after SPICLK high (clock polarity =
0)
0.5tc(SPC)S
ns
tv(SPCL-SIMO)S
Valid time, SPISIMO data valid after SPICLK low (clock polarity = 1)
0.5tc(SPC)S
ns
18
21
22
8tc(LCO)
UNIT
13
17
(4)
MAX
12
14
(1)
(2)
(3)
MIN
ns
The MASTER / SLAVE bit (SPICTL.2) is cleared and the CLOCK PHASE bit (SPICTL.3) is cleared.
tc(SPC) = SPI clock cycle time = LSPCLK/4 or LSPCLK/(SPIBRR + 1)
Internal clock prescalers must be adjusted such that the SPI clock speed is limited to the following SPI clock rate:
Master mode transmit 25-MHz MAX, master mode receive 12.5-MHz MAX
Slave mode transmit 12.5-MHz MAX, slave mode receive 12.5-MHz MAX.
The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).
Submit Documentation Feedback
Electrical Specifications
105
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
12
SPICLK
(clock polarity = 0)
13
14
SPICLK
(clock polarity = 1)
17
18
SPISOMI
SPISOMI Data Is Valid
Data Valid
21
22
SPISIMO
SPISIMO Data
Must Be Valid
SPISTE(A)
A.
In the slave mode, the SPISTE signal should be asserted low at least 0.5tc(SPC) before the valid SPI clock edge and
remain low for at least 0.5tc(SPC) after the receiving edge (SPICLK) of the last data bit.
Figure 6-21. SPI Slave Mode External Timing (Clock Phase = 1)
106
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.9.7
On-Chip Analog-to-Digital Converter
Table 6-36. ADC Electrical Characteristics (over recommended operating conditions) (1) (2)
PARAMETER
MIN
TYP
MAX
UNIT
DC SPECIFICATIONS
Resolution
12
Bits
ADC clock
1
kHz
12.5
MHz
ACCURACY
INL (Integral nonlinearity)
1-12.5 MHz ADC clock (6.25 MSPS)
±1.5
LSB
DNL (Differential nonlinearity) (3)
1-12.5 MHz ADC clock (6.25 MSPS)
±1
LSB
+60
LSB
Offset error
(4)
-60
±4
Offset error with hardware trimming
Overall gain error with internal reference
(5)
Overall gain error with external reference
LSB
-60
+60
LSB
-60
+60
LSB
Channel-to-channel offset variation
±4
LSB
Channel-to-channel gain variation
±4
LSB
ANALOG INPUT
Analog input voltage (ADCINx to ADCLO)
(6)
0
ADCLO
-5
Input capacitance
0
V
5
mV
10
pF
±5
Input leakage current
INTERNAL VOLTAGE REFERENCE
3
µA
(5)
VADCREFP - ADCREFP output voltage at the pin based on
internal reference
1.275
V
VADCREFM - ADCREFM output voltage at the pin based on
internal reference
0.525
V
0.75
V
Voltage difference, ADCREFP - ADCREFM
Temperature coefficient
50
PPM/°C
EXTERNAL VOLTAGE REFERENCE (5) (7)
VADCREFIN - External reference voltage input on ADCREFIN
pin 0.2% or better accurate reference recommended
ADCREFSEL[15:14] = 11b
1.024
V
ADCREFSEL[15:14] = 10b
1.500
V
ADCREFSEL[15:14] = 01b
2.048
V
67.5
dB
68
dB
AC SPECIFICATIONS
SINAD (100 kHz) Signal-to-noise ratio + distortion
SNR (100 kHz) Signal-to-noise ratio
THD (100 kHz) Total harmonic distortion
-79
dB
ENOB (100 kHz) Effective number of bits
10.9
Bits
83
dB
SFDR (100 kHz) Spurious free dynamic range
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Tested at 12.5 MHz ADCCLK.
All voltages listed in this table are with respect to VSSA2.
Texas Instruments specifies that the ADC will have no missing codes.
1 LSB has the weighted value of 3.0/4096 = 0.732 mV.
A single internal/external band gap reference sources both ADCREFP and ADCREFM signals, and hence, these voltages track
together. The ADC converter uses the difference between these two as its reference. The total gain error listed for the internal reference
is inclusive of the movement of the internal bandgap over temperature. Gain error over temperature for the external reference option will
depend on the temperature profile of the source used.
Voltages above VDDA + 0.3 V or below VSS - 0.3 V applied to an analog input pin may temporarily affect the conversion of another pin.
To avoid this, the analog inputs should be kept within these limits.
Texas Instruments recommends using high precision external reference Texas Instruments part REF3020/3120 or equivalent for
2.048-V reference.
Submit Documentation Feedback
Electrical Specifications
107
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.9.7.1 ADC Power-Up Control Bit Timing
ADC Power Up Delay
ADC Ready for Conversions
PWDNBG
PWDNREF
td(BGR)
PWDNADC
td(PWD)
Request for
ADC
Conversion
Figure 6-22. ADC Power-Up Control Bit Timing
Table 6-37. ADC Power-Up Delays
PARAMETER (1)
MIN
td(BGR)
Delay time for band gap reference to be stable. Bits 7 and 6 of the ADCTRL3
register (ADCBGRFDN1/0) must be set to 1 before the PWDNADC bit is enabled.
td(PWD)
Delay time for power-down control to be stable. Bit delay time for band-gap
reference to be stable. Bits 7 and 6 of the ADCTRL3 register (ADCBGRFDN1/0)
must be set to 1 before the PWDNADC bit is enabled. Bit 5 of the ADCTRL3
register (PWDNADC)must be set to 1 before any ADC conversions are initiated.
(1)
20
TYP
MAX
UNIT
5
ms
50
µs
1
ms
Timings maintain compatibility to the 281x ADC module. The 280x ADC also supports driving all 3 bits at the same time and waiting
td(BGR) ms before first conversion.
Table 6-38. Current Consumption for Different ADC Configurations (at 12.5-MHz ADCCLK) (1) (2)
ADC OPERATING MODE
CONDITIONS
VDDA18
VDDA3.3
UNIT
Mode A (Operational Mode):
•
•
BG and REF enabled
PWD disabled
30
2
mA
Mode B:
•
•
•
ADC clock enabled
BG and REF enabled
PWD enabled
9
0.5
ma
Mode C:
•
•
•
ADC clock enabled
BG and REF disabled
PWD enabled
5
20
µA
Mode D:
•
•
•
ADC clock disabled
BG and REF disabled
PWD enabled
5
15
µA
(1)
(2)
108
Test Conditions:
SYSCLKOUT = 100 MHz
ADC module clock = 12.5 MHz
ADC performing a continuous conversion of all 16 channels in Mode A
VDDA18 includes current into VDD1A18 and VDD2A18. VDDA3.3 includes current into VDDA2 and VDDAIO.
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Rs
Source
Signal
ADCIN0
Ron
1 kΩ
Switch
Cp
10 pF
ac
Ch
1.64 pF
28x DSP
Typical Values of the Input Circuit Components:
Switch Resistance (Ron):
Sampling Capacitor (Ch):
Parasitic Capacitance (Cp):
Source Resistance (Rs):
1 kΩ
1.64 pF
10 pF
50 Ω
Figure 6-23. ADC Analog Input Impedance Model
6.9.7.2 Definitions
Reference Voltage
The on-chip ADC has a built-in reference, which provides the reference voltages for the ADC.
Analog Inputs
The on-chip ADC consists of 16 analog inputs, which are sampled either one at a time or two channels at
a time. These inputs are software-selectable.
Converter
The on-chip ADC uses a 12-bit four-stage pipeline architecture, which achieves a high sample rate with
low power consumption.
Conversion Modes
The conversion can be performed in two different conversion modes:
• Sequential sampling mode (SMODE = 0)
• Simultaneous sampling mode (SMODE = 1)
Submit Documentation Feedback
Electrical Specifications
109
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.9.7.3 Sequential Sampling Mode (Single-Channel) (SMODE = 0)
In sequential sampling mode, the ADC can continuously convert input signals on any of the channels (Ax
to Bx). The ADC can start conversions on event triggers from the ePWM, software trigger, or from an
external ADCSOC signal. If the SMODE bit is 0, the ADC will do conversions on the selected channel on
every Sample/Hold pulse. The conversion time and latency of the Result register update are explained
below. The ADC interrupt flags are set a few SYSCLKOUT cycles after the Result register update. The
selected channels will be sampled at every falling edge of the Sample/Hold pulse. The Sample/Hold pulse
width can be programmed to be 1 ADC clock wide (minimum) or 16 ADC clocks wide (maximum).
Sample n+2
Sample n+1
Analog Input on
Channel Ax or Bx
Sample n
ADC Clock
Sample and Hold
SH Pulse
SMODE Bit
td(SH)
tdschx_n+1
tdschx_n
ADC Event Trigger from
ePWM or Other Sources
tSH
Figure 6-24. Sequential Sampling Mode (Single-Channel) Timing
Table 6-39. Sequential Sampling Mode Timing
SAMPLE n
SAMPLE n + 1
AT 12.5 MHz
ADC CLOCK,
tc(ADCCLK) = 80 nS
REMARKS
Acqps value = 0-15
ADCTRL1[8:11]
td(SH)
Delay time from event trigger to
sampling
2.5tc(ADCCLK)
tSH
Sample/Hold width/Acquisition
Width
(1 + Acqps) *
tc(ADCCLK)
80 ns with Acqps = 0
td(schx_n)
Delay time for first result to appear
in Result register
4tc(ADCCLK)
320 ns
td(schx_n+1)
Delay time for successive results to
appear in Result register
110
Electrical Specifications
(2 + Acqps) *
tc(ADCCLK)
160 ns
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.9.7.4 Simultaneous Sampling Mode (Dual-Channel) (SMODE = 1)
In simultaneous mode, the ADC can continuously convert input signals on any one pair of channels
(A0/B0 to A7/B7). The ADC can start conversions on event triggers from the ePWM, software trigger, or
from an external ADCSOC signal. If the SMODE bit is 1, the ADC will do conversions on two selected
channels on every Sample/Hold pulse. The conversion time and latency of the result register update are
explained below. The ADC interrupt flags are set a few SYSCLKOUT cycles after the Result register
update. The selected channels will be sampled simultaneously at the falling edge of the Sample/Hold
pulse. The Sample/Hold pulse width can be programmed to be 1 ADC clock wide (minimum) or 16 ADC
clocks wide (maximum).
NOTE
In simultaneous mode, the ADCIN channel pair select has to be A0/B0, A1/B1, ..., A7/B7,
and not in other combinations (such as A1/B3, etc.).
Sample n
Sample n+2
Sample n+1
Analog Input on
Channel Ax
Analog Input on
Channel Bx
ADC Clock
Sample and Hold
SH Pulse
SMODE Bit
td(SH)
tdschA0_n+1
tSH
ADC Event Trigger from
ePWM or Other Sources
tdschA0_n
tdschB0_n+1
tdschB0_n
Figure 6-25. Simultaneous Sampling Mode Timing
Table 6-40. Simultaneous Sampling Mode Timing
SAMPLE n
SAMPLE n + 1
AT 12.5 MHz
ADC CLOCK,
tc(ADCCLK) = 80 ns
td(SH)
Delay time from event trigger to
sampling
2.5 tc(ADCCLK)
tSH
Sample/Hold width/Acquisition
Width
(1 + Acqps) x
tc(ADCCLK)
80 ns with Acqps = 0
td(schA0_n)
Delay time for first result to
appear in Result register
4 tc(ADCCLK)
320 ns
td(schB0_n)
Delay time for first result to
appear in Result register
5 tc(ADCCLK)
400 ns
td(schA0_n+1)
Delay time for successive results
to appear in Result register
(3 + Acqps) x tc(ADCCLK)
240 ns
td(schB0_n+1)
Delay time for successive results
to appear in Result register
(3 + Acqps) x tc(ADCCLK)
240 ns
Submit Documentation Feedback
REMARKS
Acqps value = 0-15
ADCTRL1[8:11]
Electrical Specifications
111
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.10 Detailed Descriptions
Integral Nonlinearity
Integral nonlinearity refers to the deviation of each individual code from a line drawn from zero through full
scale. The point used as zero occurs one-half LSB before the first code transition. The full-scale point is
defined as level one-half LSB beyond the last code transition. The deviation is measured from the center
of each particular code to the true straight line between these two points.
Differential Nonlinearity
An ideal ADC exhibits code transitions that are exactly 1 LSB apart. DNL is the deviation from this ideal
value. A differential nonlinearity error of less than ±1 LSB ensures no missing codes.
Zero Offset
The major carry transition should occur when the analog input is at zero volts. Zero error is defined as the
deviation of the actual transition from that point.
Gain Error
The first code transition should occur at an analog value one-half LSB above negative full scale. The last
transition should occur at an analog value one and one-half LSB below the nominal full scale. Gain error is
the deviation of the actual difference between first and last code transitions and the ideal difference
between first and last code transitions.
Signal-to-Noise Ratio + Distortion (SINAD)
SINAD is the ratio of the rms value of the measured input signal to the rms sum of all other spectral
components below the Nyquist frequency, including harmonics but excluding dc. The value for SINAD is
expressed in decibels.
Effective Number of Bits (ENOB)
For a sine wave, SINAD can be expressed in terms of the number of bits. Using the following
(SINAD * 1.76)
N+
6.02
formula,
it is possible to get a measure of performance expressed as N, the effective
number of bits. Thus, effective number of bits for a device for sine wave inputs at a given input frequency
can be calculated directly from its measured SINAD.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first nine harmonic components to the rms value of the measured
input signal and is expressed as a percentage or in decibels.
Spurious Free Dynamic Range (SFDR)
SFDR is the difference in dB between the rms amplitude of the input signal and the peak spurious signal.
112
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
6.11 Flash Timing
Table 6-41. Flash Endurance
Nf
Flash endurance for the array (write/erase cycles)
NOTP OTP endurance for the array (write cycles)
-55°C to 125°C (ambient)
MIN
TYP
100
1000
MAX
UNIT
cycles
-55°C to 125°C (ambient)
1
write
MAX
UNIT
Table 6-42. Flash Parameters at 100-MHz SYSCLKOUT
PARAMETER (1)
Program
Time
Erase Time
TEST CONDITIONS
TYP
50
µs
16K Sector
500
ms
8K Sector
250
ms
4K Sector
125
ms
16K Sector
10
S
8K Sector
10
S
4K Sector
10
S
75
mA
IDD3VFLP
VDD3VFL current consumption during the
Erase/Program cycle
IDDP
VDD current consumption during Erase/Program
cycle
IDDIOP
VDDIO current consumption during Erase/Program
cycle
(1)
MIN
16-Bit Word
Erase
Program
35
mA
140
mA
20
mA
Typical parameters as seen at room temperature using flash API version 3.00 including function call overhead.
Table 6-43. Flash/OTP Access Timing
PARAMETER (1)
MIN
TYP
MAX
UNIT
ta(fp)
Paged flash access time
36
ns
ta(fr)
Random flash access time
36
ns
OTP access time
60
ns
ta(OTP)
(1)
For 100 MHz, PAGE WS = 3 and RANDOM WS = 3; for 75 MHz, PAGE WS = 2, and RANDOM WS = 2.
Equations to compute the page wait state and random wait state in Table 6-44 are as follows:
Flash Page Wait-State +
ƪǒ Ǔ ƫ
ƪǒ Ǔ ƫ
Flash Random Wait-State +
Submit Documentation Feedback
ta(fp)
t c(SCO)
*1
ta(fr)
t c(SCO)
(round up to the next highest integer) or 0, whichever is larger
* 1 (round up to the next highest integer) or 1, whichever is larger
Electrical Specifications
113
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
Table 6-44. Minimum Required Wait-States at Different Frequencies
SYSCLKOUT (ns)
PAGE WAIT-STATE
RANDOM WAIT STATE (1)
100
10
3
3
75
13.33
2
2
50
20
1
1
30
33.33
1
1
25
40
0
1
15
66.67
0
1
4
250
0
1
SYSCLKOUT (MHz)
(1)
114
Random wait state must be greater than or equal to 1.
Electrical Specifications
Submit Documentation Feedback
SM320F2808-EP, SM320F2806-EP
SM320F2801-EP
Digital Signal Processors
www.ti.com
SGLS316A – MARCH 2006 – REVISED FEBRUARY 2007
7
Mechanical Data
Table 7-1 and Table 7-2 show the thermal data.
The mechanical package diagram(s) that follow the tables reflect the most current released mechanical
data available for the designated device(s).
Table 7-1. F280x Thermal Model 100-pin GGM Results
Air Flow
PARAMETER
0 lfm
150 lfm
250 lfm
500 lfm
θJA[°C/W] High k PCB
30.58
29.31
28.09
26.62
ΨJT[°C/W]
0.4184
0.32
0.3725
0.4887
θJC
12.08
θJB
16.46
Table 7-2. F280x Thermal Model 100-pin PZ Results
Air Flow
PARAMETER
0 lfm
150 lfm
250 lfm
500 lfm
θJA[°C/W] High k PCB
48.16
40.06
37.96
35.17
ΨJT[°C/W]
0.3425
0.85
1.0575
1.410
θJC
12.89
θJB
29.58
Submit Documentation Feedback
Mechanical Data
115
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SM320F2801PZMEP
ACTIVE
LQFP
PZ
100
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
SM320F2808PZMEP
ACTIVE
LQFP
PZ
100
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
V62/06619-01XE
ACTIVE
LQFP
PZ
100
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
V62/06619-03XE
ACTIVE
LQFP
PZ
100
90
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MTQF013A – OCTOBER 1994 – REVISED DECEMBER 1996
PZ (S-PQFP-G100)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
75
0,08 M
51
76
50
100
26
1
0,13 NOM
25
12,00 TYP
Gage Plane
14,20
SQ
13,80
16,20
SQ
15,80
0,05 MIN
1,45
1,35
0,25
0°– 7°
0,75
0,45
Seating Plane
0,08
1,60 MAX
4040149 /B 11/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated