AS4LC1M16E5 ® 3V 1M×16 CMOS DRAM (EDO) Features • Organization: 1,048,576 words × 16 bits • High speed • Read-modify-write • TTL-compatible, three-state DQ • JEDEC standard package and pinout - 50/60 ns RAS access time - 20/25 ns hyper page cycle time - 12/15 ns CAS access time - 400 mil, 42-pin SOJ - 400 mil, 44/50-pin TSOP II • Low power consumption • 3V power supply (AS4LC1M16E5) • 5V tolerant I/Os; 5.5V maximum VIH • Industrial and commercial temperature available - Active: 500 mW max (-60) - Standby: 3.6 mW max, CMOS DQ • Extended data out • 1024 refresh cycles, 16 ms refresh interval - RAS-only or CAS-before-RAS refresh or self-refresh Pin arrangement Pin designation TSOP II SOJ Vcc DQ1 DQ2 DQ3 DQ4 Vcc DQ5 DQ6 DQ7 DQ8 NC NC WE RAS NC NC A0 A1 A2 A3 Vcc 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 VSS DQ16 DQ15 DQ14 DQ13 VSS DQ12 DQ11 DQ10 DQ9 NC LCAS UCAS OE A9 A8 A7 A6 A5 A4 VSS VCC DQ1 DQ2 DQ3 DQ4 VCC DQ5 DQ6 DQ7 DQ8 NC NC NC WE RAS NC NC A0 A1 A2 A3 VCC 1 2 3 4 5 6 7 8 9 10 11 15 16 17 18 19 20 21 22 23 24 25 50 49 48 47 46 45 44 43 42 41 40 36 35 34 33 32 31 30 29 28 27 26 VSS DQ16 DQ15 DQ14 DQ13 VSS DQ12 DQ11 DQ10 DQ9 NC NC LCAS UCAS OE A9 A8 A7 A6 A5 A4 VSS Pin(s) Description A0 to A9 Address inputs RAS Row address strobe DQ1 to DQ16 Input/output OE Output enable WE Write enable UCAS Column address strobe, upper byte LCAS Column address strobe, lower byte VCC Power VSS Ground Selection guide Symbol -50 -60 Unit Maximum RAS access time tRAC 50 60 ns Maximum column address access time tAA 25 30 ns Maximum CAS access time tCAC 10 12 ns Maximum output enable (OE) access time tOEA 10 12 ns Minimum read or write cycle time tRC 80 100 ns Minimum hyper page mode cycle time tHPC 20 25 ns Maximum operating current ICC1 140 120 mA Maximum CMOS standby current ICC5 1.0 1.0 mA Shaded areas indicate advance information. 4/11/01; v.1.0 Alliance Semiconductor Alliance Semiconductor P. 1 of 22 Copyright © Alliance Semiconductor. All rights reserved. AS4LC1M16E5 ® Functional description The AS4LC1M16E5 is a high performance 16-megabit CMOS Dynamic Random Access Memory (DRAM) organized as 1,048,576 words × 16 bits. The device is fabricated using advanced CMOS technology and innovative design techniques resulting in high speed, extremely low power and wide operating margins at component and system levels. The Alliance 16Mb DRAM family is optimized for use as main memory in personal and portable PCs, workstations, and multimedia and router switch applications. The AS4LC1M16E5 features hyper page mode operation where read and write operations within a single row (or page) can be executed at very high speed by toggling column addresses within that row. Row and column addresses are alternately latched into input buffers using the falling edge of RAS and xCAS inputs, respectively. Also, RAS is used to make the column address latch transparent, enabling application of column addresses prior to xCAS assertion. The AS4LC1M16E5 provides dual UCAS and LCAS for independent byte control of read and write access. Extended data out (EDO), also known as 'hyper-page mode,' enables high speed operation. In contrast to 'fast-page mode' devices, data remains active on outputs after xCAS is de-asserted high, giving system logic more time to latch the data. Use OE and WE to control output impedance and prevent bus contention during read-modify-write and shared bus applications. Outputs also go to high impedance at the last occurrance of RAS and xCAS going high. Refresh on the 1024 address combinations of A0 to A9 must be performed every 16 ms using: • RAS-only refresh: RAS is asserted while xCAS is held high. Each of the 1024 rows must be strobed. Outputs remain high impedence. • Hidden refresh: xCAS is held low while RAS is toggled. Outputs remain low impedence with previous valid data. • CAS-before-RAS refresh (CBR): At least one xCAS is asserted prior to RAS. Refresh address is generated internally. Outputs are high-impedence (OE and WE are don't care). • Normal read or write cycles refresh the row being accessed. • Self-refresh cycles The AS4LC1M16E5 is available in the standard 42-pin plastic SOJ and 44/50-pin TSOP II packages, respectively. The AS4LC1M16E5 device operates with a single power supply of 3V ± 0.3V and provides TTL compatible inputs and outputs. GND RAS UCAS RAS clock generator A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 CAS clock generator LCAS WE WE clock generator Data DQ buffers Column decoder Sense amp DQ1 to DQ16 OE Row decoder VCC Address buffers Refresh controller Logic block diagram 1024 × 1024 × 16 Array (16,777,216) Substrate bias generator Recommended operating conditions Parameter Supply voltage Input voltage Ambient operating temperature Symbol Min Nominal Max Unit VCC 3.0 3.3 3.6 V GND 0.0 0.0 0.0 V VIH 2.0 – 5.5 V –0.5 – 0.8 V 0 – 70 -40 – 85 VIL Commercial Industrial TA † °C † VIL min -3.0V for pulse widths less than 5 ns. Recommended operating conditions apply throughout this document unless otherwise specified. 4/11/01 Alliance Semiconductor 2 AS4LC1M16E5 ® Absolute maximum ratings Parameter Symbol Min Max Unit Input voltage VDQ -1.0 +5.5 V Power supply voltage VCC -1.0 +4.0 V Storage temperature (plastic) TSTG -65 +150 °C Soldering temperature × time TSOLDER – 260 × 10 o Power dissipation PD – 0.6 W Short circuit output current Iout – 50 mA C × sec Truth table Addresses RAS LCAS UCAS WE OE tR tC DQ0 to DQ15 Standby H H to X H to X X X X X High-Z Word read L L L H L ROW COL Data out Lower byte read L L H H L ROW COL Lower byte, Upper byte, Data out Upper byte read L H L H L ROW COL Lower byte, Data out, Upper byte Word (early) write L L L L X ROW COL Data in Lower byte (early) write L L H L X ROW COL Lower byte, Data in, Upper byte, High-Z Upper byte (early) write L H L L X ROW COL Lower byte, High-Z, Upper byte, Data in Read write L L L H to L L to H ROW COL Data out, Data in 1,2 1st cycle L H to L H to L H L ROW COL Data out 2 2nd cycle L H to L H to L H L n/a COL Data out 2 Any cycle L L to H L to H H L n/a n/a Data out 2 1st cycle L H to L H to L L X ROW COL Data in 1 EDO write 2nd cycle L H to L H to L L X n/a COL Data in 1 EDO read write 1st cycle L H to L H to L H to L L to H ROW COL Data out, Data in 1,2 2nd cycle L H to L H to L H to L L to H n/a COL Data out, Data in 1,2 L H H X X ROW n/a High Z CBR refresh H to L L L H X X X High Z 3 Self refresh H to L L L H X X X High Z 3 Operation EDO read RAS only refresh 4/11/01 Alliance Semiconductor Notes 3 AS4LC1M16E5 ® DC electrical characteristics -50 Parameter Symbol Test conditions -60 Min Max Min Max Unit Notes Input leakage current IIL 0V ≤ Vin ≤ VCC (max) Pins not under test = 0V -2 +2 -2 +2 µA Output leakage current IOL DOUT disabled, 0V ≤ Vout ≤ VCC (max) -2 +2 -2 +2 µA Operating power supply current ICC1 RAS, UCAS, LCAS, Address cycling; tRC=min – 140 – 130 mA TTL standby power supply current ICC2 RAS = UCAS = LCAS ≥ VIH, all other inputs at VIH or VIL – 2.0 – 2.0 mA Average power supply current, RAS refresh mode or CBR ICC3 RAS cycling, UCAS = LCAS ≥ VIH, tRC = min of RAS low after XCAS low. – 80 – 70 mA 4 EDO page mode average power supply current ICC4 RAS = VIL, UCAS or LCAS, address cycling: tHPC = min – 85 – 75 mA 4, 5 CMOS standby power supply current ICC5 RAS = UCAS = LCAS = VCC - 0.2V, F=0 – 1 – 1 mA VOH IOUT = -5.0 mA 2.4 – 2.4 – V VOL IOUT = 4.2 mA – 0.4 – 0.4 V ICC6 RAS, UCAS or LCAS cycling, tRC = min – 80 – 70 mA ICC7 RAS = UCAS = LCAS ≤ 0.2V, WE = OE ≥ VCC - 0.2V, all other inputs at 0.2V or VCC - 0.2V – 0.5 – 0.5 mA Output voltage CAS before RAS refresh current Self refresh current 4,5 Shaded areas indicate advance information. 4/11/01 Alliance Semiconductor 4 AS4LC1M16E5 ® AC parameters common to all waveforms -50 -60 Symbol Parameter Min Max Min Max Unit Notes tRC Random read or write cycle time 80 – 100 – ns tRP RAS precharge time 30 – 40 – ns tRAS RAS pulse width 50 10K 60 10K ns tCAS CAS pulse width 8 10K 10 10K ns tRCD RAS to CAS delay time 15 35 15 43 ns 9 tRAD RAS to column address delay time 9 25 10 30 ns 10 tRSH CAS to RAS hold time 10 – 10 – ns tCSH RAS to CAS hold time 40 – 50 – ns tCRP CAS to RAS precharge time 5 – 5 – ns tASR Row address setup time 0 – 0 – ns tRAH Row address hold time 8 – 10 – ns tT Transition time (rise and fall) 1 50 1 50 ns 7,8 tREF Refresh period – 16 – 16 ms 6 tCP CAS precharge time 8 – 10 – ns tRAL Column address to RAS lead time 25 – 30 – ns tASC Column address setup time 0 – 0 – ns tCAH Column address hold time 8 – 10 – ns Shaded areas indicate advance information. Read cycle -50 Symbol Parameter tRAC -60 Min Max Min Max Unit Notes Access time from RAS – 50 – 60 ns 9 tCAC Access time from CAS – 12 – 15 ns 9,16 tAA Access time from address – 25 – 30 ns 10,16 tRCS Read command setup time 0 – 0 – ns tRCH Read command hold time to CAS 0 – 0 – ns 12 tRRH Read command hold time to RAS 0 – 0 – ns 12 Shaded areas indicate advance information. 4/11/01 Alliance Semiconductor 5 AS4LC1M16E5 ® Write cycle -50 -60 Min Max Min Max Unit Write command setup time 0 – 0 – ns 14 tWCH Write command hold time 10 – 10 – ns 14 tWP Write command pulse width 10 – 10 – ns tRWL Write command to RAS lead time 10 – 10 – ns tCWL Write command to CAS lead time 8 – 10 – ns tDS Data-in setup time 0 – 0 – ns 15 tDH Data-in hold time 8 – 10 – ns 15 Symbol Parameter tWCS Notes Shaded areas indicate advance information. Read-modify-write cycle -50 -60 Symbol Parameter Min Max Min Max Unit tRWC Read-write cycle time 113 – 135 – ns tRWD RAS to WE delay time 67 – 77 – ns 14 tCWD CAS to WE delay time 32 – 35 – ns 14 42 – 47 – ns 14 tAWD Column address to Shaded areas indicate advance information. WE delay time Notes Refresh cycle -50 Symbol Parameter tCSR -60 Min Max Min Max Unit Notes CAS setup time (CAS-before-RAS) 5 – 5 – ns 6 tCHR CAS hold time (CAS-before-RAS) 8 – 10 – ns 6 tRPC RAS precharge to CAS hold time 0 – 0 – ns tCPT CAS precharge time (CBR counter test) 10 – 10 – ns Shaded areas indicate advance information. 4/11/01 Alliance Semiconductor 6 AS4LC1M16E5 ® Hyper page mode cycle -50 -60 Symbol Parameter Min Max Min Max Unit tCPWD CAS precharge to WE delay time 45 – 52 – ns tCPA Access time from CAS precharge – 28 – 35 ns tRASP RAS pulse width 50 100K 60 100K ns tDOH Previous data hold time from CAS 5 – 5 – ns tREZ Output buffer turn off delay from RAS 0 13 0 15 ns tWEZ Output buffer turn off delay from WE 0 13 0 15 ns tOEZ Output buffer turn off delay from OE 0 13 0 15 ns tHPC Hyper page mode cycle time 20 – 25 – ns tHPRWC Hyper page mode RMW cycle 47 – 56 – ns 30 – 35 – ns RAS hold time from tRHCP Shaded areas indicate advance information. CAS Notes 16 Output enable -50 Symbol Parameter tCLZ -60 Min Max Min Max Unit CAS to output in Low Z 0 – 0 – ns tROH RAS hold time referenced to OE 8 – 10 – ns tOEA OE access time – 13 – 15 ns tOED OE to data delay 13 – 15 – ns tOEZ Output buffer turnoff delay from OE 0 13 0 15 ns tOEH OE command hold time 10 – 10 – ns tOLZ OE to output in Low Z 0 – 0 – ns 0 13 0 15 ns 11,13 Notes Output buffer turn-off tOFF Shaded areas indicate advance information. time Notes 11 11 Self refresh cycle -50 Std Symbol Parameter -60 Min Max Min Max Unit tRASS RAS pulse width (CBR self refresh) 100 – 100 – µs tRPS RAS precharge time (CBR self refresh) 90 – 105 – ns tCHS CAS hold time (CBR self refresh) 8 – 10 – ns Shaded areas indicate advance information. 4/11/01 Alliance Semiconductor 7 AS4LC1M16E5 ® Notes 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Write cycles may be byte write cycles (either LCAS or UCAS active). Read cycles may be byte read cycles (either LCAS or UCAS active). One CAS must be active (either LCAS or UCAS). ICC1, ICC3, ICC4, and ICC6 are dependent on frequency. ICC1 and ICC4 depend on output loading. Specified values are obtained with the output open. An initial pause of 200 µs is required after power-up followed by any 8 RAS cycles before proper device operation is achieved. In the case of an internal refresh counter, a minimum of 8 CAS-before-RAS initialization cycles instead of 8 RAS cycles are required. 8 initialization cycles are required after extended periods of bias without clocks (greater than 8 ms). AC Characteristics assume tT = 2 ns. All AC parameters are measured with a load as described in AC test conditions below. VIH (min) and VIL (max) are reference levels for measuring timing of input signals. Transition times are measured between VIH and VIL. Operation within the tRCD (max) limit insures that tRAC (max) can be met. tRCD (max) is specified as a reference point only. If tRCD is greater than the specified tRCD (max) limit, then access time is controlled exclusively by tCAC. Operation within the tRAD (max) limit insures that tRAC (max) can be met. tRAD (max) is specified as a reference point only. If tRAD is greater than the specified tRAD (max) limit, then access time is controlled exclusively by tAA. Assumes three state test load (5 pF and a 380 Ω Thevenin equivalent). Either tRCH or tRRH must be satisfied for a read cycle. tOFF (max) defines the time at which the output achieves the open circuit condition; it is not referenced to output voltage levels. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. tWCS, tWCH, tRWD, tCWD and tAWD are not restrictive operating parameters. They are included in the datasheet as electrical characteristics only. If tWS ≥ tWS (min) and tWH ≥ tWH (min), the cycle is an early write cycle and data out pins will remain open circuit, high impedance, throughout the cycle. If tRWD ≥ tRWD (min), tCWD ≥ tCWD (min) and tAWD ≥ tAWD (min), the cycle is a read-write cycle and the data out will contain data read from the selected cell. If neither of the above conditions is satisfied, the condition of the data out at access time is indeterminate. These parameters are referenced to CAS leading edge in early write cycles and to WE leading edge in read-write cycles. Access time is determined by the longest of tCAA or tCAC or tCPA tASC ≥ tCP to achieve tPC (min) and tCPA (max) values. These parameters are sampled and not 100% tested. AC test conditions - Access times are measured with output reference levels of VOH = 2.4V and VOL = 0.4V, VIH = 2.0V and VIL = 0.8V - Input rise and fall times: 2 ns +3.3V R1 = 828Ω Dout 50 pF* R2 = 295Ω *including scope and jig capacitance GND Figure B: Equivalent output load (AS4LC1M16E5) Key to switching waveforms Rising input 4/11/01 Falling input Undefined output/don’t care Alliance Semiconductor 8 AS4LC1M16E5 ® Read waveform tRC tRAS tRCD tRSH tRP RAS tCSH tCRP tCAH tCAS tASC tRCS UCAS LCAS tRAD Address tRAL tRAH tASR Row address Column address tRRH tRCH WE tROH tWEZ tROH OE tOEZ tRAC tAA tOFF (see note 11) tOEA tCAC tREZ tCLZ DQ Data out tOLZ Upper byte read waveform tRC tRAS tRP RAS tRCD tRSH tCSH tCRP tCRP tCAS UCAS tRPC tCRP LCAS tRAH tRAL tRAD tASC tASR Address Row tCAH Column tRCH tRRH tRCS WE tROH tWEZ OE tOLZ tRAC tOEA tREZ tOEZ tAA tCAC tCLZ Upper DQ tOFF Data out Lower DQ 4/11/01 Alliance Semiconductor 9 AS4LC1M16E5 ® Lower byte read waveform tRC tRAS tRP RAS tRCD tRSH tCSH tCRP tCRP tCAS LCAS tCRP tRPC UCAS tASC tRAH tRAL tRAD tASR tCAH Address Row Column tRCH tRRH tRCS WE tROH tWEZ OE Upper DQ tRAC tREZ tOEA tOLZ tOEZ tAA tCAC tOFF tCLZ Lower DQ Data out Early write waveform tRC tRAS tRP RAS tCSH tRSH tCRP tRCD tCAS UCAS, tRAD LCAS tRAL tASC tASR Address tRAH tCAH Row address Column address tCWL tRWL tWP tWCS tWCH WE OE tDS DQ 4/11/01 tDH Data in Alliance Semiconductor 10 AS4LC1M16E5 ® Upper byte early write waveform tRC tRAS tRP RAS tASR tRAD tRAL tRAH Address Row address Column address tCAH tRSH tASC tRCD tCSH tCRP tCAS tCRP UCAS tCRP tRPC LCAS tCWL tWCH tWCS tRWL tWP WE OE tDS tDH Upper DQ Data in Lower DQ Lower byte early write waveform tRC tRAS tRP RAS tRAD tASR Address tRAL tRAH Row address Column address tCRP tRPC UCAS tASC tRCD tCAH tCAS tCSH tRSH tCRP tCRP LCAS tRWL tCWL tWCH tWP tWCS WE OE Upper DQ tDS Lower DQ 4/11/01 tDH Data in Alliance Semiconductor 11 AS4LC1M16E5 ® Write waveform OE controlled tRC tRAS tRP RAS tCSH tRSH tCRP tRCD tCAS UCAS, LCAS tRAL tRAD tRAH tASR tASC tCAH Row address Address Column address tRWL tCWL tWP WE tOEH OE tDS tOED tDH Data in DQ Upper byte write waveform OE controlled tRC tRAS tRP RAS tRAD tASR tRAL tRAH Address Row address Column address tCSH tRSH tRCD tCAH tCRP tCAS tASC tCRP UCAS tCRP tRPC LCAS tCWL tRWL tWP WE tOEH OE tDS Upper DQ tDH Data in tOED Lower DQ 4/11/01 Alliance Semiconductor 12 AS4LC1M16E5 ® Lower byte write waveform OE controlled tRC tRAS tRP RAS tRAD tASR tRAL tRAH Address Row address Column address tCAH tCAS tRCD tCSH tCRP tACS tRSH tCRP LCAS tCRP tRPC UCAS tCWL tRWL tWP WE tOEH OE Upper DQ tDH tDS Lower DQ Data in Read-modify-write waveform tRWC tRAS tRP RAS tCAS tCRP tRCD tRSH tCSH UCAS LCAS tAR tRAL tRAD tRAH tASR Address tASC tCAH Row address Column address tRWD tRWL tAWD tRCS WE tCWL tCWD tOEA tOEZ tWP tOED OE tRAC tAA tCAC tCLZ Data out DQ tDS tDH Data in tOLZ 4/11/01 Alliance Semiconductor 13 AS4LC1M16E5 ® Upper byte read-modify-write waveform tRWC tRAS tRP RAS tCSH tRCD tCAS tRSH tCRP UCAS tCRP tCRP tRPC LCAS tASR tRAD tACS tRAL tCAH tRAH Address Column address tRWD Row tCWL tRWL tAWD tCWD tRCS WE tWP tOEA OE Upper input tDS tOED tOLZ tCLZ tCAC tAA tDH Data in tOEZ tRAC Upper output Data out tOED Lower input Lower output Lower byte read-modify-write waveform tRWC tRAS tRP RAS tCRP tRPC UCAS tCSH tCAS tRSH tRCD tCRP tCRP LCAS tRAD tRAL tACS tASR tCAH tRAH Address Row Column address tCWL tRWD tRWL tWP tAWD tRCS tCWD WE tOEA OE Upper input Upper output tOLZ tOED tDH tDS tOED Lower input tRAC tAA tCAC tCLZ Data in tOEZ Lower output Data out 4/11/01 Alliance Semiconductor 14 AS4LC1M16E5 ® Hyper page mode read waveform tRASP tRP RAS tRHCP tCSH tCRP tRCD tCAS UCAS, LCAS tCP tRSH tHPC tAR tRAL tRAD tRAH tASR Address tASC Row tCAH Col address Col address Col address tRCS tRCH tRRH WE tOEA tOEA OE tRAC tCPA tCLZ tCAC tAA DQ tOEZ tOEZ tOFF tCPA Data out Data out tOLZ Data out tCLZ tCLZ Hyper page mode byte write waveform tRASP tRP RAS tCSH UCAS tRCD tCRP tCRP tRSH tCAS tCAS tHPC tCP tHPC tCRP tCAS Address tCAH tRAH tRAD tASC tASR Row tRAL tCAH Column 1 tRPC tCP LCAS tCAH tASC tASC Column 2 Column n tRCH tRCS WE tOEA tOEA tRRH tOEA OE tCAC tCLZ tAA tOLZ tCPA tOEZ Lower DQ Data out 2 tAA tRAC tCAC tCLZ tOLZ tOEZ tCAC tCLZ tAA tCPA tOFF tOEZ Upper DQ Data out 1 Data out n tOLZ 4/11/01 Alliance Semiconductor 15 AS4LC1M16E5 ® Hyper page mode early write waveform tRASP tRAH tRWL RAS tCRP tRCD tPC tCSH tCAS UCAS, LCAS tCAH tASC tCP tWCS tRSH tRAL tAR tASR Address tRAD Col address Row address Col address Col address tCWL tWP tWCH tOEH WE OE tHDR tOED tDH tDS DQ Data in Data In Data in Hyper page mode byte early write waveform tRASP tRP RAS tCSH tCRP tRCD tRSH tCAS tCAS tCRP UCAS tCP tCP tPC tPC tCAS tCRP tRPC LCAS tRAD tRAH tASR Address Row tRAL tCAH tCAH tASC tASC Column 1 Column 2 tCAH tASC Column n tRWL tWCH tWCH tWCS tWCH tWCS tWCS tWP tCWL tWP tCWL tWP tCWL WE OE tDS Lower DQ tDH Data In 2 tDS tDH tDS tDH Upper DQ Data in n Data in 1 4/11/01 Alliance Semiconductor 16 AS4LC1M16E5 ® Hyper page mode read-modify-write waveform tRASP tRP RAS tHPRWC tCSH tRCD UCAS, LCAS tCAS tCRP tRAD tASR tRAH tASC Address tCP tASC tCAH Row ad Col ad Col ad tRWD tRCS tRAL tASC tCAH tCAH Col address tCPWD tCWL tCWD tCWD tRWL tCWD tAWD tCWL tAWD tWP WE tOEA tOEZ tOED tOEA OE tAA tDH tRAC tCPA tDS tDS tCLZ tCLZ tCAC tCLZ tCAC DQ Data in tCAC Data in Data out Data out Data in Data out CAS before RAS refresh waveform WE = VIH tRC tRP tRAS RAS tRPC tCHR tCP tCSR UCAS, LCAS OPEN DQ RAS only refresh waveform WE = OE = VIH or VIL tRC tRAS tRP RAS UCAS, LCAS Address 4/11/01 tCRP tASR tRPC tRAH Row address Alliance Semiconductor 17 AS4LC1M16E5 ® Hyper page mode byte read-modify-write waveform tRASP tRP RAS tCSH tRCD tCRP tRSH tCAS tCAS tCRP UCAS tCP tCP tCAS LCAS tRAL tRAD tCAH tCAH tASR tASC Address tCAH tAWD tRAH R tASC tASC C1 Cn C2 tAWD tCPWD tAWD tCWD tCAH tAWD tCPWD tCWD tCWL tRWD tWP tRWL tCWD tCWL tAWD tCWL tWP tWP WE tOEA tOEA tOEA OE tDH tOED tDH tOED tDS tDS Upper input Data in 1 tRAC tAA tCAC tCLZ tCPA Data in n tAA tCAC tOEZ tOEZ tCLZ Upper output Data out 1 tDH tOED Data out n tDS Lower input Data in 2 tCPA tAA tOEZ tCAC tCLZ Lower output Data out 2 4/11/01 Alliance Semiconductor 18 AS4LC1M16E5 ® Hidden refresh waveform (read) tRC tRC tRAS tRP tRAS tRP RAS tCRP tCHR tRCD tRSH tCRP CAS tAR tRAD tCAH tRAH tASC tASR Row Address Col address tRCS tRRH WE tOEA OE tRAC tOFF tAA tCAC tCLZ tOEZ Data out DQ Hidden refresh waveform (write) tRC tRAS tRP RAS tCRP tRCD tRSH tCHR UCAS, LCAS tAR tRAD tRAL tRAH tASR Address tASC tCAH Row address Col address tRWL tWCR tWP tWCS tWCH WE tDS tDH tDHR DQ Data in OE 4/11/01 Alliance Semiconductor 19 AS4LC1M16E5 ® CAS before RAS refresh counter test waveform tRAS tRSH tRP RAS tCSR UCAS, tCPT tCAS tCHR LCAS tRAL tASC tCAH Address Col address tAA tCAC tCLZ tOFF tOEZ Read cycle DQ Data out tRRH tRCH tRCS WE tROH tOEA OE tRWL tCWL tWP tWCH Write cycle tWCS WE tDH tDS DQ Data in OE tRWL tRCS tWP tCWD tCWL tAWD Read-Write cycle WE tOEA t AA tCLZ DQ tDH tOEZ tCAC 4/11/01 tOED OE tDS Data out Data in Alliance Semiconductor 20 AS4LC1M16E5 ® CAS-before-RAS self refresh cycle tRP tRASS tRPS RAS tRPC tRPC tCP tCHS tCSR UCAS, LCAS tCEZ DQ Package dimensions D e c SOJ A A1 A2 B b c D E E1 E2 e E1 E2 Pin 1 E B A2 A A1 Seating Plane b c 36 35 34 33 32 31 30 29 28 27 26 50 49 48 47 46 45 44 43 42 41 40 TSOP II E He 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 10 11 d l A A1 A2 b c d E He e l 50-pin TSOP II Min Max (mm) (mm) 1.2 0.05 0.95 1.05 0.30 0.45 0.12 0.21 20.85 21.05 10.03 10.29 11.56 11.96 0.80 (typical) 0.40 0.60 A2 A A1 4/11/01 42-pin SOJ Min Max 0.128 0.148 0.025 0.105 0.115 0.026 0.032 0.015 0.020 0.007 0.013 1.070 1.080 0.370 NOM 0.395 0.405 0.435 0.445 0.050 NOM b e 0–5° Alliance Semiconductor 21 AS4LC1M16E5 ® Capacitance 15 Parameter Input capacitance DQ capacitance ƒ = 1 MHz, Ta = Room temperature Symbol Signals Test conditions Max Unit CIN1 A0 to A9 Vin = 0V 5 pF CIN2 RAS, UCAS, LCAS, WE, OE Vin = 0V 7 pF CDQ DQ0 to DQ15 Vin = Vout = 0V 7 pF AS4LC1M16E5 ordering information Package \ RAS access time 50 ns 60 ns Plastic SOJ, 400 mil, 42-pin AS4LC1M16E5-50JC AS4LC1M16E5-50JI AS4LC1M16E5-60JC AS4LC1M16E5-60JI TSOP II, 400 mil, 44/50-pin AS4LC1M16E5-50TC AS4LC1M16E5-50TI AS4LC1M16E5-60TC AS4LC1M16E5-60TI Shaded areas indicate advance information. AS4LC1M16E5 part numbering system AS4 LC 1M16E5 –XX X DRAM prefix C = 5V CMOS LC = 3.3V CMOS Device number RAS access time Package: Temperature range J = 42-pin SOJ 400 mil C=Commercial, 0°C to 70°C T = 44/50-pin TSOP II 400 mil I=Industrial, -40°C to 85°C 4/11/01; v.1.0 Alliance Semiconductor Alliance Semiconductor X P. 22 of 22 © Copyright Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their respective companies. Alliance reserves the right to make changes to this document and its products at any time without notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this data at any time, without notice. If the product described herein is under development, significant changes to these specifications are possible. The information in this product data sheet is intended to be general descriptive information for potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance). All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of products from Alliance does not convey a license under any patent rights, copyrights, mask works rights, trademarks, or any other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use.