TMDS251 www.ti.com SLLS852 – AUGUST 2007 2.5 Gbps 2-TO-1 DVI/HDMI SWITCH • FEATURES 1 • • • • • • • • Compatible with HDMI 1.3a Supports 2.5 Gbps Signaling Rate for 480i/p, 720i/p, and 1080i/p Resolutions up to 12-Bit Color Depth Integrated Switchable Receiver Termination Selectable Receiver Equalization to Accommodate to Different Input Cable Lengths Intra-Pair Skew < 40 ps Inter-Pair Skew < 65 ps HBM ESD Protection Exceeds 8 kV to TMDS Inputs 3.3-V Fixed Supply to TMDS I/Os • • • • • 5-V Fixed Supply to HPD, DDC, and Source Selection Circuits 64-Pin TQFP Package Footprint Compatible with 3-to-1 Switch TMDS351 with Port 3 Disabled ROHS Compatible and 260°C Reflow Rated TMDS250 is Available with Port 1 Disabled and Ports 2 and 3 Enabled Supports 5-V to 3.3-V Level Shifting on DDC Links APPLICATIONS • • Digital TV Digital Projector DESCRIPTION The TMDS251 is a 2-port digital video interface (DVI) or high-definition multimedia interface (HDMI) switch that allows up to 2 DVI or HDMI ports to be switched to a single display terminal. Four TMDS channels, one hot plug detector, and a digital display control (DDC) interface are supported on each port. Each TMDS channel supports signaling rates up to 2.5 Gbps to allow 1080p resolution in 12-bit color depth. The input port is enabled by configuring source selectors, S1 and S2. When an input port is selected, the TMDS inputs are connected to the TMDS outputs through a 2-to-1 multiplexer, the MOSFET between the input DDC channel and the output DDC channel is turned on, and the HPD output follows the state of the HPD_SINK. The other input port is inactive with disconnected input terminations, disconnected TMDS inputs to the outputs, disconnected DDC inputs to the outputs, and the HPD outputs are low state. Check the source selection look up table for the details of port selections. When S1 is high and S2 is low, all input terminations are disconnected, TMDS inputs are high impedance with standard TMDS terminations, all internal MOSFETs are turned off to disable the DDC links, and all HPD outputs are connected to the HPD_SINK. This allows the initiation of the HDMI physical address discovery process. Termination resistors (50-Ω), pulled up to VCC, are integrated at each TMDS receiver input. External terminations are not required. A precision resistor is connected externally from the VSADJ pin to ground for setting the differential output voltage to be compliant with the TMDS standard. Typical Application DVD Player STB Digital TV TMDS251 2-to-1 PHY SX 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2007, Texas Instruments Incorporated TMDS251 www.ti.com SLLS852 – AUGUST 2007 The TMDS251 provides two levels of receiver input equalization for different ranges of cable lengths. Each TMDS receiver owns frequency responsive equalization circuits. When EQ sets low, the receiver supports the input connection in short range HDMI cables. When EQ sets high, the receiver supports the input connection in long range HDMI cables. The TMDS251 supports power saving operation. When a system is under standby mode and there is no digital audio/visual content from a connected source, the 3.3-V supply voltage, VCC, can be powered off to minimize power consumption from the TMDS inputs, outputs, and internal switching circuits. The HPD, DDC, and source selection circuits are powered up by the 5-V supply voltage, VDD, to maintain the system hot plug detect response, the DDC link from the selected source to the sink under system standby operation. The device is characterized for operation from 0°C to 70°C. 2 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 TMDS251 www.ti.com SLLS852 – AUGUST 2007 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. FUNCTIONAL BLOCK DIAGRAM EQ Vcc RINT RINT A14 B14 TMDS Rx Vcc RINT TMDS Rx RINT A11 Z4 Y3 Vcc TMDS Driver RINT A12 B12 Y4 TMDS Driver RINT A13 B13 2-to-1 MUX Z3 TMDS Rx Vcc RINT Y2 RINT TMDS Driver TMDS Rx B11 Z2 Vcc A24 B24 RINT Y1 RINT TMDS Driver TMDS Rx Z1 Vcc RINT VSADJ RINT A23 B23 TMDS Rx Vcc RINT RINT A22 B22 TMDS Rx Vcc RINT RINT A21 B21 TMDS Rx HPD1 HPD2 S1 S2 Control Logic HPD_SINK SCL1 SDA1 SCL_SINK SDA_SINK SCL2 SDA2 HPD/DDC Power Supply VDD Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 3 TMDS251 www.ti.com SLLS852 – AUGUST 2007 49 50 51 52 53 54 A14 47 3 46 4 45 5 44 B14 Vcc A13 B13 GND A12 6 43 TMDS251 7 42 8 41 64-pin TQFP 9 40 B11 SCL1 SDA1 HPD1 EQ S2 32 31 30 29 28 B12 Vcc A11 Y1 Z1 GND SCL_SINK SDA_SINK HPD_SINK S1 27 33 26 34 16 25 35 15 24 36 14 23 13 22 37 21 38 12 20 39 11 19 10 Y4 Z4 Vcc Y3 Z3 GND Y2 Z2 Vcc 4 55 56 57 58 59 60 61 62 48 2 17 NC Vcc NC NC GND VSADJ 1 18 NC NC GND NC NC Vcc NC NC GND NC 63 64 NC A24 B24 Vcc A23 B23 GND A22 B22 Vcc A21 B21 SCL2 SDA2 HPD2 VDD PAG PACKAGE (TOP VIEW) Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 TMDS251 www.ti.com SLLS852 – AUGUST 2007 TERMINAL FUNCTIONS TERMINAL NAME I/O NO. DESCRIPTION A11, A12, A13, A14 39, 42, 45, 48 I Source port 1 TMDS positive inputs A21, A22, A23, A24 54, 57, 60, 63 I Source port 2 TMDS positive inputs B11, B12, B13, B14 38, 41, 44, 47 I Source port 1 TMDS negative inputs B21, B22, B23, B24 53, 56, 59, 62 I Source port 2 TMDS negative inputs Y1, Y2, Y3, Y4 26,23,20,17 O Sink port TMDS positive outputs Z1, Z2, Z3, Z4 27,24,21,18 O Sink port TMDS negative outputs SCL1 37 I/O Source port 1 DDC I2C clock line SDA1 36 I/O Source port 1 DDC I2C data line SCL2 52 I/O Source port 2 DDC I2C clock line SDA2 51 I/O Source port 2 DDC I2C data line SCL_SINK 29 I/O Sink port DDC I2C clock line SDA_SINK 30 I/O Sink port DDC I2C data line HPD1 35 O Source port 1 hot plug detector output (status pin) HPD2 50 O Source port 2 hot plug detector output (status pin) HPD_SINK 31 I Sink port hot plug detector input (status pin) 32, 33 I Source selector EQ 34 I TMDS Input equalization selector (control pin) EQ = Low – HDMI 1.3 compliant cable EQ = High – 10m 28 AWG HDMI cable VSADJ 16 I TMDS compliant voltage swing control (control pin) S1, S2 VDD 49 VCC 6, 12, 19, 25, 40, 46, 55, 61 HPD/DDC Power supply Power supply GND 3, 9, 15, 22, 28, 43, 58 Ground 1, 2, 4, 5, 7, 8, 10, 11, 13, 14, 64 NC No connect: these pins should be left floating Table 1. Source Selection Lookup (1) CONTROL BITS (1) I/O SELECTED HOT PLUG DETECT STATUS S2 S1 Y/Z SCL_SINK SDA_SINK H H A1/B1 Terminations of A2/B2 are disconnected SCL1 SDA1 HPD_SINK L H L A2/B2 Terminations of A1/B1 are disconnected SCL2 SDA2 L HPD_SINK L L Disallowed (indeterminate) State All terminations are disconnected L L L H None (Z) All terminations are disconnected HPD_SINK HPD_SINK None (Z) Are pulled HIGH by external pull-up termination HPD1 HPD2 H: Logic high; L: Logic low; X: Don't care; Z: High impedance Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 5 TMDS251 www.ti.com SLLS852 – AUGUST 2007 EQUIVALENT INPUT AND OUTPUT SCHEMATIC DIAGRAMS TMDS Input Stage TMDS Output Stage VCC VCC Y Z 50 W 50 W A B 10 mA Status and Source Selector Control Input Stage VDD VCC HPD_SINK S1 S2 EQ DDC Pass Gate HPD Output Stage VDD VDD HPD1 HPD2 6 SCL/SDA Source Submit Documentation Feedback SCL/SDA Sink Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 TMDS251 www.ti.com SLLS852 – AUGUST 2007 ORDERING INFORMATION (1) (1) PART NUMBER PART MARKING PACKAGE TMDS251PAGR TMDS251 64-PIN TQFP Tape/Reel For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) UNIT Supply voltage range (2) Voltage range VCC –0.5 V to 4 V VDD –0.5 V to 6 V Anm (3), Bnm 2.5 V to 4 V Ym, Zm, VSADJ, EQ –0.5V to 4 V SCLn, SCL_SINK, SDAn, SDA_SINK, HPDn, HPD_SINK, S1, S2 –0.5 V to 6 V Human body model (4) Electrostatic discharge Anm, Bnm, Ym, Zm ±8000 V All pins ±4000 V Charged-device model (5) (all pins) Machine model (6) ±1500 V (all pins) ±200 V See Dissipation Rating Table Continuous power dissipation (1) (2) (3) (4) (5) (6) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values, except differential I/O bus voltages, are with respect to network ground terminal. n = 1, 2; m = 1, 2, 3, 4 Tested in accordance with JEDEC Standard 22, Test Method A114-B Tested in accordance with JEDEC Standard 22, Test Method C101-A Tested in accordance with JEDEC Standard 22, Test Method A115-A DISSIPATION RATINGS PACKAGE TA ≤ 25°C Low-K 1111 mW 11.19 mW/°C 611 mW High-K 1492 mW 14.92 820 mW 64-TQFP PAG (1) DERATING FACTOR ABOVE TA = 25°C (1) PCB JEDEC STANDARD TA = 70°C POWER RATING This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow. THERMAL CHARACTERISTICS over operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX (1) UNIT RθJB Junction-to-board thermal resistance 33.4 °C/W RθJC Junction- to-case thermal resistance 15.6 °C/W PD Device power dissipation (1) VIH = VCC, VIL = VCC - 0.6 V, RT = 50 Ω, AVCC = 3.3V, Am/Bm(2:4) = 2.5-Gbps HDMI data pattern, Am/Bm(1) = 250-MHz clock 590 750 mW UNIT The maximum rating is simulation under 3.6-V VCC, 5.5-V VDD, and 600 mV VID. RECOMMENDED OPERATING CONDITIONS VCC Supply voltage VDD Standby supply voltage MIN NOM MAX 3 3.3 3.6 V 4.5 5 5.5 V Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 7 TMDS251 www.ti.com SLLS852 – AUGUST 2007 RECOMMENDED OPERATING CONDITIONS (continued) MIN TA Operating free-air temperature NOM MAX UNIT 0 70 °C VCC–0.4 VCC+0.01 V TMDS DIFFERENTIAL PINS VIC Input common mode voltage VID Receiver peak-to-peak differential input voltage 150 1560 mVp-p RVSADJ Resistor for TMDS compliant voltage swing range 3.66 4.02 4.47 kΩ AVCC TMDS output termination voltage, see Figure 1 3 3.3 3.6 V RT Termination resistance, see Figure 1 45 50 Signaling rate 55 Ω 0 2.5 Gbps CONTROL PINS VIH LVTTL High-level input voltage 2 VCC V VIL LVTTL Low-level input voltage GND 0.8 V GND VDD V DDC I/O PINS VI(DDC) DDC Input voltage STATUS and SOURCE SELECTOR PINS VIH LVTTL High-level input voltage 2 VDD V VIL LVTTL Low-level input voltage GND 0.8 V ELECTRICAL CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER ICC Supply current IDD Power supply current, 5-V TYP (1) MAX S1/S2 = Low/Low, Low/High, High/High 176 200 S1/S2 = High/Low 8 20 2 5 mA TEST CONDITIONS VIH = VCC, VIL = VCC – 0.6 V, RT = 50 Ω, AVCC = 3.3 V Am/Bm(2:4) = 2.5 Gbps HDMI data pattern Am/Bm(1) = 250 MHz clock MIN UNIT mA VIH = VCC, VIL = VCC – 0.6 V, RT = 50 Ω, AVCC = 3.3 V Am/Bm(2:4) = 2.5 Gbps HDMI data pattern Am/Bm(1) = 250 MHz clock TMDS DIFFERENTIAL PINS VOH Single-ended high-level output voltage AVCC–10 AVCC+10 mV VOL Single-ended low-level output voltage AVCC–600 AVCC–400 mV Vswing Single-ended output swing voltage 400 600 mV VOD(O) Overshoot of output differential voltage VOD(U) Undershoot of output differential voltage ΔVOC(SS) Change in steady-state common-mode output voltage between logic states I(OS) Short circuit output current See Figure 3 VI(open) Single-ended input voltage under high impedance input or open input II = 10 µA RINT Input termination resistance VIN = 2.9 V See Figure 2, AVCC = 3.3 V, RT = 50 Ω 15% 2× Vswing 25% 2× Vswing 5 mV -12 12 mA VCC–10 VCC+10 mV 45 50 55 Ω CONTROL PINS IIH High-level digital input current (2) VIH = 2 V or VCC -10 10 µA IIL Low-level digital input current (2) VIL = GND or 0.8 V -10 10 µA -10 10 µA 10 pF 40 Ω 2.7 V DDC I/O PINS Ilkg Input leakage current VI = 0.1 VDD to 0.9 VDD to isolated DDC inputs CIO Input/output capacitance VI(pp) = 1 V, 100 kHz RON Switch resistance IO = 3 mA, VO = 0.4 V VPASS Switch output voltage VI = 5 V, IO = 100 µA 27 2.4 STATUS AND SOURCE SELECTOR PINS (1) (2) 8 All typical values are at 25°C and with a 3.3-V supply. IIH and IIL specifications are not applicable to the VSADJ pin. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 TMDS251 www.ti.com SLLS852 – AUGUST 2007 ELECTRICAL CHARACTERISTICS (continued) over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP (1) MAX UNIT IIH High-level digital input current VIH = 2 V or VDD -10 10 µA IIL Low-level digital input current VIL = GND or 0.8 V -10 10 µA VOH TTL High-level output voltage IOH = –100 μA 2.4 VDD V VOL TTL Low-level output voltage IOL = 100 μA GND 0.4 V SWITCHING CHARACTERISTICS (1) over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP (2) MAX UNIT TMDS DIFFERENTIAL PINS (Y/Z) tPLH Propagation delay time, low-to-high-level output 400 650 900 ps tPHL Propagation delay time, high-to-low-level output 400 650 900 ps tr Differential output signal rise time (20% - 80%) 60 80 140 ps tf Differential output signal fall time (20% - 80%) 60 80 140 ps tsk(p) Pulse skew (|tPHL – tPLH|) (3) 6 20 ps tsk(D) Intra-pair differential skew, see Figure 4 20 40 ps tsk(o) Inter-pair channel-to-channel output skew (4) 30 65 ps tsk(pp) Part-to-part skew (5) 510 ps tjit(pp) Peak-to-peak output jitter from Yj/Zj(1) residual jitter 8 20 ps tjit(pp) Peak-to-peak output jitter from Yj/Zj(2:4) residual jitter 60 80 ps tSX Select to switch output ten Enable time tdis See Figure 2, AVCC = 3.3 V, RT = 50 Ω See Figure 5, Am/Bm(1) = 250 MHz clock, Am/Bm(2:4) = 2.5 Gbps HDMI pattern 50 70 ns 170 200 ns Disable time 9 15 ns tpd(DDC) Propagation delay from SCLn to SCL_SINK or SDAn to SDA_SINK or SDA_SINK to SDAn 8 15 ns tsx(DDC) Switch time from SCLn to SCL_SINK 8 15 ns tpd(HPD) Propagation delay (from HPD_SINK to the active port of HPD) 14 20 ns tsx(HPD) Switch time from port select to the latest valid status of HPD 33 50 ns (1) (2) (3) (4) (5) See Figure 6, 10-mA Current source to the input See Figure 7, CL = 10 pF Measurements are made with the Agilent 81250 ParBert System with a N4872A generator (600 fs tJIT(CLK), 13 ps tJIT(pp)) and a N4873A analyzer. All typical values are at 25°C and with a 3.3-V supply. tsk(p) is the magnitude of the time difference between tPLH and tPHL of a specified terminal. tsk(o) is the magnitude of the difference in propagation delay times between any specified terminals of a sink-port bank when inputs of the active source port are tied together. tsk(pp) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices operate with the same source, the same supply voltages, at the same temperature, and have identical packages and test circuits. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 9 TMDS251 www.ti.com SLLS852 – AUGUST 2007 PARAMETER MEASUREMENT INFORMATION AVcc RT RT ZO = RT TMDS Driver TMDS Receiver ZO = RT Figure 1. Termination for TMDS Output Driver Vcc R R INT INT RT Y A VA TMDS Receiver VID TMDS Driver CL 0.5 pF B VB V ID VY AVcc RT Z = VA − VB Vswing = VY − VZ VZ VA VB DC Coupled Vcc AC Coupled Vcc+0.2 V Vcc−0.4 V Vcc−0.2 V 0.4 V VID V VID(pp) ID 0V −0.4 V t PHL t PLH 100% 80% Vswing V OD(O) 0V Differential VOD(pp) 20% 0% tf tr VOD(U) V OC nVOC(SS) NOTE: All input pulses are supplied by a generator having the following characteristics: tr or tf < 100 ps, 100 MHz from Agilent 81250. CL includes instrumentation and fixture capacitance within 0.06 m of the D.U.T. Measurement equipment provides a bandwidth of 20 GHz minimum. Figure 2. TMDS Input, Output, and Timing Definitions 10 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 TMDS251 www.ti.com SLLS852 – AUGUST 2007 PARAMETER MEASUREMENT INFORMATION (continued) 50 W IOS TMDS Driver 50 W + _ 0 V or 3.6 V Figure 3. Short Circuit Output Current Test Circuit VOH VY 50% VZ VOL tsk(D) Figure 4. Definition of Intra-Pair Differential Skew AVcc RT Data + Data Video Patterm Generator Coax Coax SMA RX + SMA EQ HDMI Cables 1000 mVpp Differential M U X OUT <2" 50! Transmission Line <2" 50! Transmission Line SMA SMA RT Coax Coax TMDS251 AVcc Jitter Test Instrument RT Clk+ Clk- Coax Coax SMA RX SMA + EQ M U X OUT <2" 50! Transmission Line <2" 50! Transmission Line SMA SMA RT Coax Coax Jitter Test Instrument TP1 TP2 TP3 A. HDMI 1.3 compliant cable when EQ = Low, and 10m 28AWG input cable when EQ = High. B. All jitters are measured in BER of 10-9 C. The residual jitter reflects the total jitter measured at the output of the DUT, TP3, subtract the total jitter from the signal generator, TP1 Figure 5. Jitter Test Circuit Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 11 TMDS251 www.ti.com SLLS852 – AUGUST 2007 PARAMETER MEASUREMENT INFORMATION (continued) Port 1 A B Port 2 A B S1 Clocking VDD 2 VDD 0V S2 tSX tSX 75 mV Output -75 mV 75 mV Hi-Z -75 mV ten tdis Figure 6. TMDS Outputs Control Timing Definitions VDD 2 HPD_SINK VDD 2 0.4 V HPD1 tpd(HPD) tsx(HPD) tpd(HPD) 2.4 V HPD2 S1 VDD 2 S2 VDD tsx(DDC) SDA_SINK 1.5V tpd(DDC) tpd(DDC) SDA1 1.5V SDA2 0V Figure 7. Port Switch Timing Definitions 12 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 TMDS251 www.ti.com SLLS852 – AUGUST 2007 TYPICAL CHARACTERISTICS SUPPLY CURRENT vs SIGNAL RATE SUPPLY CURRENT vs FREE-AIR TEMPERATURE 200 200 S1 = S2 = HIGH 150 VCC = AVCC = 3.3 V, TA = 25°C, TP1 VID(PP) = 1200 mVPP, RVSADJ = 4.02 kW, Am/Bm(2:4) HDMI Data pattern, 250 Mbps-2.5 Gbps Am/Bm(1) Clock, 25 MHz-250 MHz 100 50 S1 = HIGH S2 = LOW ICC - Supply Current - mA ICC - Supply Current - mA S1 = S2 = HIGH VCC = AVCC = 3.3 V, 150 VID(PP) = 1200 mVPP, RVSADJ = 4.02 kW, Am/Bm(2:4) 2.5-Gbps HDMI Data pattern, Am/Bm(1) 250-MHz Clock 100 50 IDD 0 0 250 450 650 850 1050 1250 1450 1650 1850 2450 0 Signal Rate - Mbps 20 30 40 50 60 TA - Free Air Temperature - °C Figure 9. RESIDUAL PEAK-TO-PEAK JITTER (Data Channels) vs SIGNAL RATE RESIDUAL PEAK-TO-PEAK JITTER (Clock Channel) vs FREQUENCY 70 5 See Note A See Note A Peak-to-Peak Jitter - % Tbit Peak-to-Peak Jitter - % Tbit 10 Figure 8. 20 15 EQ = LOW 5m 28 AWG 10 IDD S1 = HIGH S2 = LOW EQ = HIGH 15m 26 AWG 5 4 EQ = HIGH 15m 26 AWG 3 EQ = HIGH 10m 28 AWG EQ = LOW 3m 30 AWG 2 1 EQ = HIGH 10m 28 AWG EQ = LOW 5m 28 AWG EQ = LOW 3m 30 AWG 0 750 A. 950 0 1150 1485 1850 Signal Rate - Mbps Channels 2, 3, 4, VCC = AVCC = 3.3 V, TA = 25°C, RVSADJ = 4.02 kΩ, See Figure 5 Figure 10. 75 2250 95 115 148.5 185 225 f - Frequency - MHz A. Channel 1, VCC = AVCC = 3.3 V, TA = 25°C, RVSADJ = 4.02 kΩ, See Figure 5 Figure 11. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 13 TMDS251 www.ti.com SLLS852 – AUGUST 2007 TYPICAL CHARACTERISTICS (continued) RESIDUAL PEAK-TO-PEAK JITTER (Data Channel) vs CABLE 20 RESIDUAL PEAK-TO-PEAK JITTER (Data Channel) vs CABLE 20 See Note A See Note A Peak-to-Peak Jitter - % Tbit 16 14 12 EQ = Low 10 8 EQ = High 6 Peak-to-Peak Jitter - % Tbit 18 15 EQ = Low EQ = High 10 5 4 2 0 0 1.5m 30AWG A. 14 3m 30 AWG 5m 28AWG Cable 10m 28AWG 1.5m 30AWG 15m 26AWG 1080p 10-Bit, VCC = AVCC = 3.3 V, TA = 25°C, RVSADJ = 4.02 kΩ, See Figure 5, Clock Channel = 185.6 MHz, Data Channel = 1.856 Gbps Figure 12. A. 3m 30 AWG 5m 28AWG Cable 10m 28AWG 15m 26AWG 1080p 12-Bit, VCC = AVCC = 3.3 V, TA = 25°C, RVSADJ = 4.02 kΩ, See Figure 5, Clock Channel = 222.8 MHz, Data Channel = 2.228 Gbps Figure 13. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 TMDS251 www.ti.com SLLS852 – AUGUST 2007 APPLICATION INFORMATION Supply Voltage The TMDS251 is powered up with two different power sources. One is 3.3-V VCC for the TMDS circuitry, and the other is 5-V VDD for HPD, DDC, and most of the control logic. It is recommended to provide the same 3.3-V power source to the TMDS circuitry of the TMDS251 and its output termination voltage. This minimizes the leakage current from the ESD protection circuitry. When the digital television (DTV) is in standby mode operation, the same common 3.3-V power source can be turned on or off. Either way will minimize the leakage current in the device, and in the receiver connected at the output where the termination is integrated. TMDS Inputs Selectable frequency response equalization circuitries are provided to all twelve differential input to support short range and long range cable connections. The frequency response compensation curves and target cable losses are shown in Figure 14 and Figure 15. 0 -1 EQ = Low -2 3m 30 AWG cable -3 Loss - dB -4 -5 spec -6 -7 -8 -9 -10 -11 -12 -13 0 250 500 750 1000 1250 1500 1750 2000 f - Frequency - MHz Figure 14. Frequency Response Compensation Curve at EQ = L Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 15 TMDS251 www.ti.com SLLS852 – AUGUST 2007 0 -2 -4 spec -6 Loss -dB -8 -10 10m cable -12 -14 EQ = High -16 -18 -20 0 250 500 750 1000 1250 1500 1750 2000 f - Frequency - MHz Figure 15. Frequency Response Compensation Curve at EQ = H Internal termination circuitry which can be switched on or off, provides 50-Ω resistance to each differential input pin when a port is selected. External terminations are not required. When the termination is switched on, current will flow to the TMDS driver. When a port is not selected, the termination is open. This stops supply current flowing from the input pins of the unselected ports. This switchable termination provides the connected HDMI source another method of determining the sink port status, and whether it is selected or not selected, without referring to the HPD pin status. TMDS Input Fail-Safe The TMDS input does not incorporate a fail-safe circuit. To implement fail-safe, the input can be externally biased to prevent output oscillation. One pin can be pulled high to VCC with the other grounded through a 1-kΩ resistor as shown in Figure 16. VCC RINT RINT RT A B TMDS Receiver TMDS Driver Y AVCC Z RT Figure 16. TMDS Input Fail-Safe Recommendation TMDS Outputs A 10% precision resistor, 4.02-kΩ, is recommended to control the output swing to the HDMI compliant 400 mV to 600 mV range (500 mV typical). The TMDS outputs are high impedance under standby mode operation, S1 = H and S2 = L. 16 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 TMDS251 www.ti.com SLLS852 – AUGUST 2007 HPD Pins The HPD circuits are powered by the 5-V supply. They provide 5-V TTL output signals to the SOURCE with a typical 1-kΩ output resistance. An external 1-kΩ resistor is not needed here. The HPD output of the selected source port follows the logic level of the HPD_SINK input. Unselected HPD outputs are kept low. When the device is in standby mode, all HPD outputs follow HPD_SINK. A 1-kΩ resistor to ground keeps all HPD outputs low in standby mode if a fixed low state is preferred. DDC Channels The DDC circuits (SDA, SCL) are powered by a 5-V supply. The I/O pins can connect to the 5-V termination voltages directly. A 47-kΩ pull-up resistor to the 5 V is recommended on the SCL1 and SCL2 pins. There is no pull-up resistor on the SDA pins. The pull-up resistor can be replaced with a different value. Source Sink VDDSink VDDSource VCCRx RupSink RupSource RupRx I to-Source Ron SCL SDA SCL_SINK SDA_SINK I to-Sink Driver (Source) Driver (Sink) Figure 17. Simplified Electrical Circuit Model for DDC Channel In Figure 17, when the Driver (Sink) pulls the bus low, the highest voltage level is Vol(Sink)max. The current flow through the pass-gate resistor can be presented as: Vdd * V ol(Sink)max Ito * Sink + RupSource ø R upSink (1) where the Vddsource = Vddsink = Vdd To simplify the equation, Vol(Sink)max is set equal to 0 V to reach equation (2): Vdd lto * Sink + RupSource ø R upSink (2) The voltage at the input of the SINK is Ito - Sink × Ron + Vol(Sink)max, which should be lower than the minimum input low threshold voltage of the Driver (Source), Vith(Source)min to keep the bus in correct interoperations. V ith(Source)min u lto * Sink Ron ) V ol(Sink)max (3) By combining equations (2) and (3), the minimum pull-up resistor at the Sink input is: V dd Ron RupSource R upSink w (Vith(Source)min * Vol(Sink)max) RupSource * V dd Ron (4) Applying the same methodology to calculate the pull-up resistor at the input of the Driver (Sink), the minimum pull-up resistor is: V ccRx Ron R upRx w (Vith(Sink)min * Vol(Source)max) (5) The data sheet VPASS specification ensures the maximum output voltage is clamped at 3.6 V to support a 3.3-V connection. Resistors pulling up to 3.3 V on SCL_SINK and SDA_SINK ensure the high level does not exceed the 3.3-V termination voltage. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 17 TMDS251 www.ti.com SLLS852 – AUGUST 2007 Layout Considerations The high-speed differential TMDS inputs are the most critical paths for the TMDS251. There are several considerations to minimize discontinuities on these transmission lines between the connectors and the device: • Maintain 100-Ω differential transmission line impedance into and out of the TMDS251 • Keep an uninterrupted ground plane beneath the high-speed I/Os • Keep the ground-path vias to the device as close as possible to allow the shortest return current path • Keep the trace lengths of the TMDS signals between connector and device as short as possible Using the TMDS251 in Systems with Different CEC Link Requirements The TMDS251 supports a DTV with up to three HDMI inputs when used in conjunction with a signal-port HDMI receiver or three HDMI inputs when used in conjunction with a dual-port HDMI receiver. Figure 18 and Figure 19 show simplified application block diagrams for the TMDS251 in different DTVs with different consumer electronic control (CEC) requirements. The CEC is an optional feature of the HDMI interface for centralizing and simplifying user control instructions from multiple audio/video products in an inter-connected system, even when all the audio/video products are from different manufacturers. This feature minimizes the number of remote controls in a system, as well as reducing the number of times buttons need to be pressed. A DTV Supporting a Passive CEC Link In Figure 18, the DTV does not have the capability of handling CEC signals, but allows CEC signals to pass over the CEC bus. The source selection is done by the control command of the DTV. The user cannot force the command from any audio/video product on the CEC bus. The selected source reads the E-EDID data after receiving an asserted HPD signal. The micro-controller loads different CEC physical addresses while changing the source by means of the S1 and S2 pins. E-EDID Reading Configurations in Standby Mode When the DTV system is in standby mode, the sources will not read the E-EDID memory because the 1-kΩ pull-down resistor keeping the HPD_SINK input at logic low forces all HPD pins to output logic low to all sources. The source will not read the E-EDID data with a low on HPD signal. However, if reading the E-EDID data in the system standby mode is preferred, then TMDS251 can still support this need. The recommended configuration sequences are: 1. Apply the same 3.3-V power to the VCC of TMDS251 and the TMDS line termination at the HDMI receiver 2. Turn off VCC, and keep VDD on. The TMDS circuit is off, but the HPD, the DDC and the source selection circuits are active. 3. Set S1 and S2 to select the source port which is allowed to read the E-EDID memory. Please note if the source has a time-out limitation between the 5 V and the HPD signals, the above configuration is not applicable. Uses individual EEPROMs assigned for each input port, see Figure 19. The solution uses E-EDID data to be readable during system power off or standby mode operations. 18 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 TMDS251 www.ti.com SLLS852 – AUGUST 2007 SINK HPD 5V HPD 5V HPD1 5V SOURCE 1 SDA SCL CEC CLK D0 D1 D2 CLK D0 D1 D2 HPD 5V HPD 5V SDA SCL CEC SDA SCL CEC CLK D0 D1 D2 CLK D0 D1 D2 VCC (3.3V) EQ 47kW SDA SCL CEC VDD (5V) SDA1 SCL1 mController S1 S2 CEC A21/B11 A22/B12 A23/B13 A24/B14 HPD_SINK 1kW 3.3V 4.7kW HPD2 5V 47kW SOURCE 2 4.7kW DDC_SDA DDC_SCL SDA_SINK SCL_SINK E-EDID SDA2 SCL2 HDMI RX CEC Y1/Z1 Y2/Z2 Y3/Z3 Y4/Z4 Y1/Z1 Y2/Z2 Y3/Z3 Y4/Z4 A21/B21 A22/B22 A23/B23 A24/B24 GND VSadj 4.02kW 10% Figure 18. Two-Port HDMI Enabled DTV with TMDS251 – CEC Commands Passing Through A DTV Supporting an Active CEC Link In Figure 19, R, and S, the CEC PHY and CEC LOGIC functions are added. The DTV can initiate and/or react to CEC signals from its remote control or other audio/video products on the same CEC bus. All sources must have their own CEC physical address to support the full functionality of the CEC link. A source reads its CEC physical address stored its E-EDID memory after receiving a logic-high from the HPD feedback. When HPD is high, the sink-assigned CEC physical address should be maintained. Otherwise, when HPD is low the source sets CEC physical address value to (F.F.F.F). Case 1 – AC Coupled Source (See Figure 19, Port 1) When the source TMDS lines are AC coupled or when the source cannot detect the TMDS termination provided in the connected sink, the indication of the source selection can only come from the HPD signal. The TMDS251 HPD1 pin should be applied directly as the HPD signal back to the source. Case 2 – DC Coupled Source (See Figure 19, Port 2) When the source TMDS lines are DC coupled, there are two methods to inform the source that it is the active source to the sink. One is checking the HPD signal from the sink, and the other is checking the termination condition in the sink. In a full CEC operation mode, the HPD signal is set high whether the port is selected or not. The source loads and maintains the CEC physical address when HPD is high. As soon as HPD goes low, the source loses the CEC physical address. To keep the CEC physical address to the source, the HPD signal is looping back from the source provided 5-V signal through a 1-kΩ pull-up resistor in the sink. This method is acceptable in application where the HDMI transmitter can detect the receiver termination by current sensing, and the receiver has switchable termination on the TMDS inputs. The internal termination resistors are connected to the termination voltage when the port is selected, or they are disconnected when the port is not selected. The TMDS251 features switchable termination on the TMDS inputs. Case 3 – External Logic Control for HPD (See Figure 19, Port 3) When the HDMI transmitter does not have the capability of detecting the receiver termination, using the HPD signal as a reference for sensing port selections is the only possible method. External control logic for switching the connections of the HPD signals between the HPD pins of the TMDS251 and the 5-V signal from the source provides a good solution. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 19 TMDS251 www.ti.com SLLS852 – AUGUST 2007 E-EDID Reading Configurations in Standby Mode When the TMDS251 is in standby mode operation, S1 = H and S2 = L, all sources can read their E-EDID memories simultaneously with all HPD pins following HPD_SINK in logic-high. HPD_SINK input low will prevent E-EDID reading in standby mode operation. SINK HPD 5V SOURCE with AC coupled HDMI output HPD 5V SDA SCL CEC SDA SCL CEC CLK D0 D1 D2 CLK D0 D1 D2 HPDx VDD (5V) VCC (3.3V) SDA SCL EQ 5V 47kW mController S1 S2 SDAx SCLx CEC LOGIC CEC E-EDID Ax1/Bx1 Ax2/Bx2 Ax3/Bx3 Ax4/Bx4 HPD_SINK 1kW CEC PHY 3.3V 4.7kW 4.7kW DDC_SDA DDC_SCL SDA_SINK SCL_SINK HDMI RX Y1/Z1 Y2/Z2 Y3/Z3 Y4/Z4 Y1/Z1 Y2/Z2 Y3/Z3 Y4/Z4 VSadj GND 4.02kW 10% Figure 19. Two-Port HDMI Enabled DTV with TMDS251 – AC Coupled Source - CEC Commands Active SINK HPD 5V HPD 5V 1kW 5V 47kW SOURCE with DC coupled HDMI output SDA SCL CEC SDA SCL CEC CLK D0 D1 D2 CLK D0 D1 D2 HPDx VDD (5V) VCC (3.3V) SDA SCL EQ mController S1 S2 SDAx SCLx CEC LOGIC CEC E-EDID Ax1/Bx1 Ax2/Bx2 Ax3/Bx3 Ax4/Bx4 HPD_SINK 1kW CEC PHY 3.3V 4.7kW SDA_SINK SCL_SINK 4.7kW DDC_SDA DDC_SCL HDMI RX Y1/Z1 Y2/Z2 Y3/Z3 Y4/Z4 GND Y1/Z1 Y2/Z2 Y3/Z3 Y4/Z4 VSadj 4.02kW 10% Figure 20. Two-Port HDMI Enabled DTV with TMDS251 – DC Coupled Source - CEC Commands Active 20 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 TMDS251 www.ti.com SLLS852 – AUGUST 2007 SINK SOURCE in general HDMI output HPD 5V HPD 5V SDA SCL CEC SDA SCL CEC CLK D0 D1 D2 CLK D0 D1 D2 1kW 5V 47kW HPDx VDD (5V) VCC (3.3V) SDA SCL EQ mController S1 S2 SDAx SCLx CEC LOGIC CEC E-EDID Ax1/Bx1 Ax2/Bx2 Ax3/Bx3 Ax4/Bx4 HPD_SINK 1kW CEC PHY 3.3V 4.7kW SDA_SINK SCL_SINK 4.7kW DDC_SDA DDC_SCL HDMI RX Y1/Z1 Y2/Z2 Y3/Z3 Y4/Z4 GND Y1/Z1 Y2/Z2 Y3/Z3 Y4/Z4 VSadj 4.02kW 10% Figure 21. Two-Port HDMI Enabled DTV with TMDS251 – External Logic - CEC Commands Active Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TMDS251 21 MECHANICAL DATA MTQF006A – JANUARY 1995 – REVISED DECEMBER 1996 PAG (S-PQFP-G64) PLASTIC QUAD FLATPACK 0,27 0,17 0,50 48 0,08 M 33 49 32 64 17 0,13 NOM 1 16 7,50 TYP Gage Plane 10,20 SQ 9,80 12,20 SQ 11,80 0,25 0,05 MIN 1,05 0,95 0°– 7° 0,75 0,45 Seating Plane 0,08 1,20 MAX 4040282 / C 11/96 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Falls within JEDEC MS-026 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 5-Oct-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TMDS251PAGR ACTIVE TQFP PAG 64 1500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TMDS251PAGRG4 ACTIVE TQFP PAG 64 1500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 4-Oct-2007 TAPE AND REEL BOX INFORMATION Device TMDS251PAGR Package Pins PAG 64 Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) SITE 60 330 24 13.0 13.0 1.4 16 Pack Materials-Page 1 W Pin1 (mm) Quadrant 24 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 4-Oct-2007 Device Package Pins Site Length (mm) Width (mm) Height (mm) TMDS251PAGR PAG 64 SITE 60 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA MTQF006A – JANUARY 1995 – REVISED DECEMBER 1996 PAG (S-PQFP-G64) PLASTIC QUAD FLATPACK 0,27 0,17 0,50 48 0,08 M 33 49 32 64 17 0,13 NOM 1 16 7,50 TYP Gage Plane 10,20 SQ 9,80 12,20 SQ 11,80 0,25 0,05 MIN 1,05 0,95 0°– 7° 0,75 0,45 Seating Plane 0,08 1,20 MAX 4040282 / C 11/96 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Falls within JEDEC MS-026 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated