SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 FEATURES • • • • • • • • Single-Chip Mixer/Oscillator and PLL Synthesizer Three-Band Local Oscillator I2C Bus Protocol (Bidirectional Data Transmission) 30-V Tuning Voltage Output Four NPN-Type Band-Switch Drivers Programmable Reference Divider Ratio (512, 640, or 1024 ) 5-V Power Supply 30-Pin TSSOP Package APPLICATIONS • • • TV VCR/DVD Recorder Set-Top Box DESCRIPTION DBT PACKAGE (TOP VIEW) VHI OSC C VHI OSC B OSC GND VLO OSC C VLO OSC B UHF OSC B1 UHF OSC C1 UHF OSC C2 UHF OSC B2 IF GND VCC IF OUT1 IF OUT2 CP VTU 1 30 2 29 3 28 4 27 5 26 6 25 7 24 8 23 9 22 10 21 11 20 12 19 13 18 14 17 15 16 UHF RF IN2 UHF RF IN1 VHF RF IN RF GND MIX OUT2 MIX OUT1 BS4 BS2 BS1 BS3 ADC AS SDA SCL XTAL P0038-01 The SN761681 is a synthesized tuner IC designed for TV tuning systems. The circuit consists of a PLL synthesizer, three-band local oscillator and mixer, 30-V output tuning amplifier, four NPN band-switch drivers, and is available in a small-outline package. A 15-bit programmable counter and reference divider are controlled by I2C bus protocol. Tuning step frequency is selectable by this reference divider ratio for a crystal oscillator. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2005, Texas Instruments Incorporated SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. VHF-L Osc VCC MIX OUT1 MIX OUT2 UHF OSC B2 UHF OSC C2 UHF OSC B1 VHF-H Osc UHF OSC C1 VHI OSC C VHI OSC B OSC GND VLO OSC C VLO OSC B Functional Block Diagram UHF Osc IF Amp IF OUT1 IF OUT2 VHF Mixer VHF RF IN IF GND UHF Mixer UHF RF IN1 UHF RF IN2 1/8 Prescaler 1/32, 1/33 Prescaler CP 15-Bit Counter VTU RF GND XTAL Op Amp XTAL Osc 4 MHz 512/640/1024 Divider Charge Pump Phase Detector NPN Band Switch Port SCL SDA 2 I C Bus Interface AS BS4 BS3 BS2 BS1 ADC 5-Level ADC B0089-02 2 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 Pin Assignments Pin Description TERMINAL NAME DESCRIPTION NO. SCHEMATIC ADC 20 ADC input Figure 1 AS 19 Address selection input Figure 2 BS1 22 Band switch1 output (NPN emitter follower) Figure 3 BS2 23 Band switch2 output (NPN emitter follower) Figure 3 BS3 21 Band switch3 output (NPN emitter follower) Figure 3 BS4 24 Band switch4 output (NPN emitter follower) Figure 3 CP 14 Charge pump output Figure 4 IF GND 10 IF ground IF OUT1 12 IF output Figure 5 IF OUT2 13 IF output Figure 5 MIX OUT1 25 Mixer output Figure 6 MIX OUT2 26 Mixer output Figure 6 OSC GND 3 Oscillator ground RF GND 27 RF ground SCL 17 Serial clock input Figure 7 SDA 18 Serial data input/output Figure 8 UHF OSC B1 6 UHF oscillator base1 Figure 9 UHF OSC B2 9 UHF oscillator base2 Figure 9 UHF OSC C1 7 UHF oscillator collector1 Figure 9 UHF OSC C2 8 UHF oscillator collector2 Figure 9 UHF RF IN1 29 UHF RF input Figure 10 UHF RF IN2 30 UHF RF input Figure 10 VCC 11 Supply voltage for mixer/oscillator/PLL: 5-V VHF RF IN 28 VHF RF input Figure 11 VHI OSC B 2 VHF HIGH oscillator base Figure 12 VHI OSC C 1 VHF HIGH oscillator collector Figure 12 VLO OSC B 5 VHF LOW oscillator base Figure 13 VLO OSC C 4 VHF LOW oscillator collector Figure 13 VTU 15 Tuning voltage amplifier output Figure 14 XTAL 16 4-MHz crystal oscillator input Figure 15 150 kW 20 19 50 kW S0159-01 S0133-03 Figure 1. Figure 2. 3 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 21 14 22 23 50 kW 24 S0138-02 S0156-01 Figure 3. Figure 4. 25 26 12 13 S0160-01 S0155-01 Figure 5. Figure 6. 18 17 S0136-03 S0133-02 Figure 7. 4 Figure 8. SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 29 8 7 9 6 3 kW 30 3 kW S0142-05 S0130-01 Figure 9. Figure 10. 1 28 2 3 kW 3 kW S0142-04 S0129-01 Figure 11. Figure 12. 15 4 5 3 kW 3 kW S0129-02 S0157-01 Figure 13. Figure 14. 5 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 16 S0158-01 Figure 15. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) Supply voltage, VCC (2) VCC (Pin 11) –0.4 V to 6.5 V Input voltage 1, VGND (2) RF GND, OSC GND (Pins 3, 27) –0.4 V to 0.4 V Input voltage 2, VVTU (2) VTU –0.4 V to 35 V Input voltage 3, VIN (2) Other pins (Pins 1, 2, 4–9, 12–14, 16–26, 28–30) –0.4 V to 6.5 V Continuous total dissipation, PD (3) TA ≤ 25°C 1071 mW Operating free-air temperature, TA –20°C to 85°C Storage temperature range, Tstg –65°C to 150°C Maximum junction temperature, TJ 150°C Maximum short-circuit time, tSC(max) (1) (2) (3) Each pin to VCC or to GND 10 s Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Voltage values are with respect to the IF GND of the circuit. Derating factor is 8.57 mW/°C for TA ≥ 25°C. RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) Supply voltage, VCC MIN NOM MAX 4.5 5 5.5 V 30 33 V 10 mA 85 °C Tuning supply voltage, VTU Output current of band switch, IBS Operating free-air temperature, TA 6 One port on –20 UNIT SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 ELECTRICAL CHARACTERISTICS, Total Device and Serial Interface VCC = 4.5 V to 5.5 V, TA = –20°C to 85°C, unless otherwise noted PARAMETER TEST CONDITIONS MIN TYP MAX UNIT ICC1 Supply current 1 ICC2 Supply current 2 VIH High-level input voltage (SCL, SDA) VIL Low-level input voltage (SCL, SDA) 1.4 V IIH High-level input current (SCL, SDA) 10 µA IIL Low-level input current (SCL, SDA) –10 VPOR Power-on-reset supply voltage (threshold of supply voltage between reset and operation mode) 2.1 One band switch on (IBS = 10 mA) 60 mA 70 mA 2.8 VCC V µA 2.8 3.5 V I2C INTERFACE VASH Address-select high-input voltage (AS) VCC = 5 V 4.5 5 V VASM1 Address-select mid1-input voltage (AS) VCC = 5 V 2 3 V VASM2 Address-select mid2-input voltage (AS) VCC = 5 V 1 1.5 V VASL Address-select low-input voltage (AS) VCC = 5 V 0.5 V IASH Address-select high-input current (AS) 140 µA IASL Address-select low-input current (AS) VADC ADC input voltage See Table 8 IADH ADC high-level input current VADC = VCC IADL ADC low-level input current VADC = 0 V VOL Low-level output voltage (SDA) VCC = 5 V, IOL = 3 mA 0.4 V lSDAH High-level output leakage current (SDA) VSDA = 5.5 V 10 µA fSCL Clock frequency (SCL) 400 kHz µA –50 0 VCC V 10 µA µA –50 100 I2C Timing (see timing chart, Figure 16) thd(DAT) Data hold time 0 µs t(BUF) Bus free time 1.3 µs thd(STA) Start hold time 0.6 µs t(Low) SCL-low hold time 1.3 µs t(High) SCL-high hold time 0.6 µs tsu(STA) Start setup time 0.6 µs tsu(DAT) Data setup time 0.1 µs tr SCL, SDA rise time 0.3 µs tf SCL, SDA fall time 0.3 µs tsu(STO) Stop setup time 0.6 µs 7 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 ELECTRICAL CHARACTERISTICS, PLL and Band Switch VCC = 4.5 V to 5.5 V, TA = –20°C to 85°C, unless otherwise noted PARAMETER TEST CONDITIONS MIN N Divider ratio 15-bit frequency word 256 fXTAL Crystal oscillator frequency RXTAL = 25 Ω to 300 Ω 3.2 ZXTAL Crystal oscillator input impedance VIXTAL2 Minimum reference input sensitivity (XTAL) 4 MHz, ac coupling with 0.1 µF capacitor VVTUL Tuning amplifier low-level output voltage RL = 22 kΩ, VTU = 33 V IVTUOFF Tuning amplifier leakage current (off) OS = 1, VTU = 33 V ICPH Charge-pump high-level input current ICPL Charge-pump low-level input current CP = 0 VCP Charge-pump output voltage PLL locked ICPOFF Charge-pump leakage current T2 = 0, T1 = 1, VCP = 2 V, TA = 25°C IBS Band-switch driver output current VBS1 VBS2 IBSOFF 8 Band-switch driver output voltage Band-switch driver leakage current TYP MAX 4 4.48 1.6 0.3 CP = 1 IBS = 10 mA IBS = 10 mA, VCC = 5 V, TA = 25°C VBS = 0 V 0.4 MHz kΩ 100 mVp-p 0.5 V 10 µA 280 µA 60 µA 1.95 V –15 15 nA 10 mA 3 3.5 UNIT 32767 V 3.9 3 µA SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 ELECTRICAL CHARACTERISTICS, Mixer, Oscillator, IF Amplifier VCC = 5 V, TA = 25°C, measured in Figure 17 reference measurement circuit at 50-Ω system, IF filter characteristics: fpeak = 43 MHz (unless otherwise noted) PARAMETER Gc1 Gc3 Gc4 Gc6 Gc7 Gc9 NF1 MIN TYP MAX (1) Conversion gain (mixer-IF amplifier), fin = 58 MHz VHF-LOW fin = 130 MHz (1) 22 25 28 22 25 28 (1) Conversion gain (mixer-IF amplifier), fin = 136 MHz VHF-HIGH fin = 364 MHz (1) 22 25 28 22 25 28 (1) Conversion gain (mixer-IF amplifier), fin = 370 MHz VHF-UHF fin = 804 MHz (1) 26 29 32 25 28 31 fin = 55.25 MHz 9.5 fin = 127.25 MHz 9.5 fin = 133.25 MHz 10 fin = 361.25 MHz 10 fin = 367.25 MHz 11 fin = 801.25 MHz 11 1% cross-modulation distortion, VHF-LOW fin = 55.25 MHz (2) 89 MHz (2) 89 1% cross-modulation distortion, VHF-HIGH fin = 133.25 MHz (2) 86 fin = 361.25 MHz (2) 86 fin = 367.25MHz (2) 87 fin = 801.25 MHz (2) 87 fin = 55.25 MHz (3) 117 Noise figure, VHF-LOW NF3 NF4 Noise figure, VHF-HIGH NF6 NF7 Noise figure, UHF NF9 CM1 CM3 CM4 CM6 CM7 CM9 VIFO1 VIFO3 VIFO4 VIFO6 VIFO7 VIFO9 ΦOSC1 ΦOSC3 ΦOSC4 ΦOSC6 ΦOSC7 ΦOSC9 TEST CONDITIONS 1% cross-modulation distortion, UHF IF output voltage, VHF-LOW IF output voltage, VHF-HIGH IF output voltage, UHF Phase noise, VHF-LOW Phase noise, VHF-HIGH Phase noise, UHF fin = 127.25 MHz (3) 117 fin = 133.25 MHz (3) 117 fin = 361.25 MHz (3) 117 fin = 367.25MHz (3) 117 MHz (3) 117 fin = 127.25 fin = 801.25 fin = 55.25 MHz (4) 88 fin = 127.25 MHz (4) 88 fin = 133.25 MHz (4) 86 fin = 361.25 MHz (4) 86 fin = 367.25MHz (4) 84 MHz (4) 84 fin = 801.25 Prescaler beat (5) (1) (2) (3) (4) (5) UNIT dB dB dB dB dB dB dBµV dBµV dBµV dBµV dBµV dBµV dBc/Hz dBc/Hz dBc/Hz 25 dBµV IF = 43 MHz, RF input level = 80 dBµV fundes = fdes ±6 MHz, Pin = 80 dBµV, AM 1 kHz, 30%, DES/CM = S/I = 46 dB IF = 45.75 MHz Offset = 10 kHz, RF input level = 70 dBµV Design parameter, not tested 9 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 Functional Description I2C Bus Mode I2C Write Mode (R/W = 0) Table 1. Write Data Format MSB LSB (1) Address byte (ADB) 1 1 0 0 0 MA1 MA0 R/W = 0 A Divider byte 1 (DB1) 0 N14 N13 N12 N11 N10 N9 N8 A Divider byte 2 (DB2) N7 N6 N5 N4 N3 N2 N1 N0 A Control byte (CB) 1 CP T2 T1 T0 RSA RSB OS A Band-switch byte (BB) X X X X BS4 BS3 BS2 BS1 A (1) A: Acknowledge Table 2. Description of Data Symbols SYMBOL DESCRIPTION MA[1:0] Address-set bits (see Table 3, Address Selection) N[14:0] Programmable counter set bits DEFAULT N14 = N13 = N12 = ... = N0 = 0 N = N14 × 214 + N13 × 213 + ... + N1 × 2 + N0 Oscillation frequency = fr × 8 × N fr = Reference frequency = 4 MHz/Reference divider CP Charge-pump current-set bit CP = 1 60 µA (CP = 0), 280 µA (CP = 1) T[2:0] TEST bits (see Table 4, Test Bits) T[2:0] = 001 Normal mode: T2 = 0, T1 = 0, T0 = 1/0 RSA, RSB Reference divider ratio selection bits RSA = 0, RSB = 1 See Table 6, Reference Divider Ratio. OS Tuning amplifier control bit OS = 0 Tuning voltage on (OS = 0) Tuning voltage off, high impedance (OS = 1) BS[4:1] Band-switch control bits BSn = 0 BSn = 0: Tr = OFF BSn = 1: Tr = ON Band selection by BS1, BS2, BS4 X 10 BS1(VL) BS2(VH) BS4(U) 1 X X 0 1 X 0 0 1 Don't care VHF-LO VHF-HI UHF SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 Table 3. Address Selection MA1 MA0 Voltage Applied on AS Input 0 0 LOW: 0 V to 0.1 VCC 0 1 MID2: open, or 0.2 VCC to 0.3 VCC 1 0 MID1: 0.4 VCC to 0.6 VCC 1 1 HIGH: 0.9 VCC to VCC Table 4. Test Bits (1) (1) T2 T1 T0 0 0 0 Normal operation Device Operation 0 0 1 Normal operation 0 1 X Charge pump is off. 1 1 0 Charge pump is sink. 1 1 1 Charge pump is source. 1 0 X Test mode Note Default ADC not available Not used for other bit patterns Table 5. Reference Divider Ratio RSA RSB Reference Divider Ratio X 0 640 0 1 1024 1 1 512 I2C Read Mode (R/W = 1) Table 6. Read Data Format MSB Address byte (ADB) Status byte (SB) (1) LSB (1) 1 1 0 0 0 MA1 MA0 R/W = 1 A POR FL 1 1 1 A2 A1 A0 – A: Acknowledge Table 7. Description of Data Symbols SYMBOL DESCRIPTION MA[1:0] Address-set bits (see Table 3, Address Selection) POR Power-on-reset flag DEFAULT POR = 1 POR set: Power on POR reset: End-of-data transmission procedure FL In-lock flag A[2:0] Digital data of ADC (see Table 8, ADC Level) PLL locked (FL = 1), PLL unlocked (FL = 0) 11 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 Table 8. ADC Level (1) Voltage Applied on ADC Input (1) A2 A1 A0 1 0 0 0.6 VCC to VCC 0 1 1 0.45 VCC to 0.6 VCC 0 1 0 0.3 VCC to 0.45 VCC 0 0 1 0.15 VCC to 0.3 VCC 0 0 0 0 V to 0.15 VCC Accuracy is 0.03 × VCC. t(High) tr t(Low) SCL thd(STA) tsu(DAT) tf thd(DAT ) tsu(STA) tsu(STO) SDA t(BUF) T0101-01 2 Figure 16. I C Timing Chart 12 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 APPLICATION INFORMATION Reference Measurement Circuit C27 X1 16 15 R10 SCL C28 R11 C29 R12 19 C30 20 C43 21 IF OUT2 BS3 C42 C41 ADC VCC BS3 IF GND BS1 UHF OSC B2 9 R19 C12 R3 7 6 MIX OUT1 UHF OSC B1 MIX OUT2 VLO OSC B C10 VC3 C9 L4 RF GND VLO OSC C R18 R5 R2 C6 VC2 4 27 R14 3 28 VHF RF IN C5 C7 OSC GND C8 L2 2 29 C40 C14 5 26 UHF RF IN1 VHI OSC B UHF RF IN2 VHI OSC C C2 1 30 UIN1 R4 C13 UHF OSC C1 25 C34 VIN VCC C17 C11 UHF OSC C2 24 L5 C35 C18 C21 8 U1 BS4 L6 R21 L3 BS4 C33 IF OUT1 C20 10 BS2 C44 R22 11 23 BS2 IF OUT2 C25 IF OUT1 22 BS1 C24 C23 12 AS ADC C22 13 SDA AS C36 CP 18 SDA TU R8 14 17 SCL R7 VTU XTAL L1 C1 C38 C4 C3 UIN2 C39 VC1 R1 C16 S0161-01 NOTE: This application information is advisory and a performance check is required for actual application circuits. TI assumes no responsibility for the consequences of the use of this circuit nor for any infringement of patent or patent rights of third parties which may result from its use. Figure 17. Reference Measurement Circuit 13 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 APPLICATION INFORMATION (continued) Component Values for Measurement Circuit PART NAME VALUE PART NAME VALUE C1 (VHI OSC C) 3 pF C39 (UIN2) 2.2 nF C2 (VHI OSC B) 2 pF C40 (VIN) 2.2 nF C3 (VHI OSC) 68 pF C41 (BS2) 2.2 nF C4 (VHI OSC) Open C42 (BS1) 2.2 nF C5 (VLO OSC C) 1 pF C43 (BS3) 2.2 nF C6 (VLO OSC B) 1 pF C44 (BS4) 2.2 nF C7 (VLO OSC) 47 pF L1 (VHI OSC) φ2,4 mm, 4T, wire 0,4 mm C8 (VLO OSC) 3 pF L2 (VLO OSC) φ3 mm, 8T, wire 0,32 mm C9 (UHF OSC B1) 1.5 pF L3 (UHF OSC) φ3 mm, 2T, wire 0,4 mm C10 (UHF OSC C1) 1.5 pF L4 (UHF OSC) φ2 mm, 3T, wire 0,4 mm C11 (UHF OSC C2) 1.5 pF L5 (MIXOUT) φ2,4 mm, 16T, wire 0,26 mm C12 (UHF OSC B2) 1.5 pF L6 (MIXOUT) φ2,4 mm, 16T, wire 0,26 mm C13 (UHF OSC) 12 pF R1(VHI OSC) 33 kΩ C14 (UHF OSC) 100 pF R2 (VLO OSC) 33 kΩ C16 (VTU) 2.2 nF/50 V R3 (UHF OSC) 22 kΩ C17 (VTU) 2.2 nF/50 V R4 (UHF OSC) 33 kΩ C18 (VTU) 2.2 nF/50 V R5 (VTU) 22 kΩ C20 (IF OUT1) 2.2 nF R7 (CP) 22 kΩ C21 (VCC) 4.7 nF R8 (VTU) 22 kΩ C22 (CP) 2.2 nF R10 (SCL) 330 Ω C23 (CP) 0.1 µF/50 V R11 (SDA) 330 Ω C24 (VTU) 2.2 nF/50 V R12 (AS) 330 Ω C25 (IF OUT2) 2.2 nF R14 (MIXOUT) 0 C27 (XTAL) 68 pF R18 (UHF OSC) 0 C28 (SCL) Open R19 (UHF OSC) 0 C29 (SDA) Open R21 (IF OUT1) Open C30 (AS) Open R22 (IF OUT2) 51 Ω C33 (MIXOUT) Open U1 SN761681 C34 (MIXOUT) 22 pF VC1 (VHI OSC) 1T363A C35 (MIXOUT) Open VC2 (VLO OSC) 1T363A C36 (MIXOUT) 4.7 nF VC3 (UHF OSC) 1T363A C38 (UIN1) 2.2 nF X1 4-MHz crystal 14 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 Test Circuits DUT SG VHF RF IN 50 W 50 W IF OUT1 VIN Spectrum Analyzer VOUT Diff VOUT IF OUT2 50 W Gc = 20log(VOUT Diff/VIN) = 20log(VOUT/VIN) + 6 50 W S0144-02 Figure 18. VHF-Conversion Gain-Measurement Circuit DUT SG UHF RF IN1 50 W 50 W VIN IF OUT1 UHF RF IN2 Spectrum Analyzer VOUT Diff VOUT IF OUT2 50 W Gc = 20log(VOUT Diff/VIN) = 20log(VOUT/VIN) + 6 50 W S0145-01 Figure 19. UHF-Conversion Gain-Measurement Circuit NF Meter Noise Source DUT B0090-01 Figure 20. Noise-Figure Measurement Circuit Signal Generator fdes: P = 80 dBmV Signal Generator Mix Pad fdes ±6 MHz AM 30%, 1 kHz DUT Modulation Analyzer B0091-01 Figure 21. 1% Cross-Modulation Distortion Measurement Circuit 15 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 TYPICAL CHARACTERISTICS Band-Switch Driver Output Voltage (BS1–BS4) BS OUTPUT CURRENT vs OUTPUT VOLTAGE 5 VCC = 5.5 V VCC = 5 V VSS − Supply Voltage − V 4 VCC = 4.5 V 3 2 1 0 −2 −4 −6 −8 −10 −12 −14 −16 −18 −20 IBS − BS Current IBS −mA G001 Figure 22. Band-Switch Driver Output Voltage S-Parameter 1 0 ¥ 50 MHz 400 MHz 1 M0047-04 Figure 23. VHF Input 16 SN761681 TV TUNER IC www.ti.com SLES165 – DECEMBER 2005 TYPICAL CHARACTERISTICS (continued) 1 0 ¥ 900 MHz 350 MHz 1 M0047-05 Figure 24. UHF Input 1 60 MHz 30 MHz 0 ¥ 1 M0047-06 Figure 25. IF Output 17 PACKAGE OPTION ADDENDUM www.ti.com 14-Mar-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN761681DBT ACTIVE SM8 DBT 30 60 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN761681DBTG4 ACTIVE SM8 DBT 30 60 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN761681DBTR ACTIVE SM8 DBT 30 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN761681DBTRG4 ACTIVE SM8 DBT 30 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated