ETC TA75S393F

General-Purpose Linear ICs
Operational Amplifier ICs & Comparator ICs z 118
Intelligent Power Devices (IPD) z 122
Interface Drivers z 125
Motor Drivers z 130
Power Supply ICs z 134
Small-Signal MMICs (High-Frequency Cell-pack) z 142
117
Operational Amplifier ICs & Comparator ICs
Operational Amplifier ICs & Comparator ICs (Bipolar, Single-Circuit Type)
Features
Operating Voltage
Pin Configuration (top view)
(Unit: mm)
SMV
Bipolar comparator
TA75S393F
SMV
TA
Single/dual power supply,
open-collector output
2 to 36 V
or
±1 to ±18 V
TA75S01F
SMV
SA
Single/dual power supply,
unity gain available
3 to 12 V
or
±1.5 to ±6 V
TA75S558F
SMV
SB
Dual power supply
±4 to ±18 V
−
+
SMV
Bipolar op amp
Note:
2.9
2.8
Marking
1.6
Package
2.8
Part Number
1.6
Function
2.9
+
−
Please note that the pin configurations of the input pins of the single operational amps and comparator differ. The US8 and SM8 types have the same pin configuration.
(Bipolar, Dual-Circuit Type)
Function
Part Number
Package
Marking
Features
Operating Voltage
Pin Configuration (top view)
(Unit: mm)
SM8
2.9
TA75W393FU
SM8
5W393
−
B +
2.8
Bipolar comparator
Single/dual power supply,
open-collector output
2 to 36 V
or
±1 to ±18 V
+
A −
TA75W01FU
SM8
5W01
Single/dual power supply,
unity gain available
3 to 12 V
or
±1.5 to ±6 V
US8
B
TA75W558FU
118
SM8
5W558
Dual power supply
±4 to ±18 V
A
+
−
−
+
2.3
2.0
Bipolar op amp
(CMOS, Single-Circuit Type)
Function
Part Number
Package
TC75S56F
TC75S56FU
TC75S56FE
TC75S57F
TC75S57FU
TC75S57FE
TC75S58F
TC75S58FU
TC75S58FE
TC75S59F
TC75S59FU
TC75S59FE
TC75S51F
TC75S51FU
TC75S51FE
TC75S54F
TC75S54FU
TC75S54FE
TC75S55F
TC75S55FU
TC75S55FE
CMOS comparator
CMOS op amp
USV
TD
Single/dual power supply,
push-pull output,
low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
TE
Single/dual power supply,
open-drain output,
ultra-low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
TF
Single/dual power supply,
open-drain output,
low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
SC
Single/dual power supply,
low-voltage operation
1.5 to 7 V
or
±0.75 to ±3.5 V
SE
Single/dual power supply,
low-voltage operation,
low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
SF
Single/dual power supply,
low-voltage operation,
ultra-low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
SH
Single/dual power supply,
high slew rate, high fT,
low-voltage operation,
low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
ESV
ESV
SMV
USV
ESV
SMV
USV
ESV
SMV
USV
ESV
SMV
USV
ESV
SMV
* TC75S60FU
USV
Pin Configuration
−
+
+
−
Please note that the pin configurations of the input pins of the single operational amps and comparator differ. The US8 and SM8 types have the same pin configuration.
USV
ESV
1.6
1.6
2.1
2.0
1.25
1.6
2.9
*: New product
1.2
SMV
2.8
TC
SMV
USV
Operating Voltage
1.8 to 7 V
or
±0.9 to ±3.5 V
SMV
USV
Features
Single/dual power supply,
push-pull output,
ultra-low current consumption
ESV
* TC75S60F
Note:
Marking
SMV
(mm)
(CMOS, Dual-Circuit Type)
TC75W56FU
Package
Marking
US8
TC75W57FU
SM8
TC75W57FK
US8
TC75W58FU
SM8
Single/dual power supply,
push-pull output,
ultra-low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
5W57
Single/dual power supply,
push-pull output,
low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
5W58
Single/dual power supply,
open-drain output,
ultra-low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
5W59
Single/dual power supply,
open-drain output,
low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
5W51
Single/dual power supply,
low-voltage operation
1.5 to 7 V
or
±0.75 to ±3.5 V
5W54
Single/dual power supply,
low-voltage operation,
low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
CMOS comparator
CMOS op amp
TC75W58FK
US8
TC75W59FU
SM8
TC75W59FK
US8
TC75W51FU
SM8
TC75W51FK
US8
TC75W54FU
SM8
TC75W54FK
US8
TC75W55FU
US8
* TC75W60FU
SM8
* TC75W60FK
5W55
Single/dual power supply,
low-voltage operation,
ultra-low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
5W60
Single/dual power supply,
high slew rate, high fT,
low-voltage operation,
low current consumption
1.8 to 7 V
or
±0.9 to ±3.5 V
SM8
TC75W55FK
US8
Operating Voltage
5W56
SM8
TC75W56FK
Features
Pin Configuration (top view)
(Unit: mm)
SM8
2.9
−
B +
2.8
Part Number
+
A −
US8
2.0
B
A
+
−
−
+
2.3
Function
*: New product
119
Power Op-Amp
Circuit
Dual
120
Part Number
TA7256P
TA7272P
Package
Maximum Ratings
IO (A)
VCC (V)
Remarks
HSIP10
±18
0.5
Internally phase-corrected type
HSIP10
±18
1.2
Internally phase-corrected type
Calculation Amplifier IC Series
Classification
Use/Function
Circuit
High-speed,
low-power
Single power supply
op-amps
Dual power supply
op-amps
(Op-Amp Series)
Dual
General-purpose,
low-power
General-purpose
Dual
Quad
Dual
Part Number
TA75358F
TA75358P
TA75358CF
TA75358CP
TA75902F
TA75902P
TA75458F
TA75458P
Package
SOP8
DIP8
SOP8
DIP8
SOP14
DIP14
SOP8
DIP8
Recommended
VCC (V)
VIO (mV)
Max
IIO (nA)
Max
II (nA)
Max
7
50
250
1.5
0.8
1.2
3 to 36
⎯
7
50
250
0.6
0.3
1.2
3 to 36
358
2904
7
30
150
⎯
⎯
1.2
3 to 36
2902
5
200
500
1.1
0.8
6
±15
1458
fT (MHz) SR (V/µs) ICC (mA)
Typ.
Typ.
Max
Remarks
Equivalent
(Comparator ICs)
Part Number
TA7522S
TA7522F
Circuit
Remarks
SIP9
+18
0.3 µA
10 mV
−2 µA
―
Open-collector output
Dual
SOP8
+18
0.3 µA
10 mV
−2 µA
―
Open-collector output
Quad
DIP14
SOP14
TA75393P
TA75393AP
TA75393F
Power Supply Input Offset Current Input Offset Voltage Input Bias Current Response Speed
(V)
Max
Max
Max
Typ.
Dual
TA75339P
TA75339AP
TA75339F
Package
Dual
DIP8
SOP8
Equivalent
⎯
⎯
LM339N
LM2901N
±18
50 nA
5 mV
250 nA
tr = 1.3 µs
or
+36
70 nA
10 mV
250 nA
tr = 1.0 µs
50 nA
5 mV
250 nA
tr = 1.3 µs
⎯
50 nA
5 mV
250 nA
tr = 1.3 µs
LM393N
LM2903N
±18
or
+36
50 nA
7 mV
250 nA
tr = 1.3 µs
50 nA
5 mV
250 nA
tr = 1.3 µs
High output current: 100 mA Typ.
High output current: 100 mA Typ.
⎯
⎯
⎯
TA8504F
Single
SOP8
−5
10 µA
±10 mV
40 µA
tr = 1.0 ns
tf = 0.7 ns
ECL output
⎯
TA8517F
Dual
SOP16
+5
3 µA
±10 mV
6 µA
tr = 4.0 ns
tf = 2.0 ns
TTL output
Comes with offset adjustment pin.
⎯
121
Intelligent Power Devices (IPD)
60 V Series
Operating
Junction
Protective Functions
Operating
Power
Supply
(Channel)
Over
Temperature
Dissipation Overcurrent
Overvoltage Short
Voltage
Temperature
Temperature
Topr (°C)
PD (W)
IS (A)
VS (V)
load
(V)
Tj (°C)
TS (°C)
Part Number
Use/Function
Outline
TPD1008SA
High-side
switch
VDSS 60 V
IO 4 A
RDS(ON) = 0.2 Ω Max
5 to 18
TPD1009S
High-side
switch
VDSS 60 V
IO 8 A
RDS(ON) = 0.06 Ω Max
5 to 18
TPD1011S
High-side
switch
VDSS 60 V
IO 15 A
RDS(ON) = 0.06 Ω Max
5 to 18
−40 to 85
TPD1018F
High-side
switch
VDSS 60 V
IO 0.5 A
RDS(ON) = 0.8 Ω Max
5 to 25
−40 to 125
TPD1024S
Low-side
switch
VDS(DC) 40 V
IO 1.5 A
RDS(ON) = 0.5 Ω Max
up to 18
TPD1024AS
Low-side
switch
VDS(DC) 40 V
IO 1.5 A
RDS(ON) = 0.5 Ω Max
up to 18
2-ch low-side
switch
VDS(DC) 40 V
IO 1 A
RDS(ON) = 0.6 Ω Max
Low-side
switch
2-ch low-side
switch
TPD1030F
TPD1031AF
TPD1032F
Diagnostic Functions
Input/
Open
Over
Overvoltage Output
load Temperature
Package
6 Typ.
160
Typ.
⎯
○
DIAG
L
○
DIAG
H
○
DIAG
L
⎯
H/H
TO-220(NIS)
5PIN
12 Typ.
160
Typ.
⎯
○
DIAG
L
○
DIAG
H
○
DIAG
L
⎯
H/H
TO-220(NIS)
5PIN
160
Typ.
○
○
○
40 Typ.
⎯
DIAG
L
DIAG
H
DIAG
L
⎯
H/H
TO-220(IS)
5PIN
○
1.5 Typ.
160
Typ.
○
0.3
30 Typ.
DIAG
L
⎯
DIAG
L
DIAG
L
H/H
SSOP-10PIN
−40 to 85
1
3.5 Typ.
160
Typ.
Active
clamp
40 Min
⎯
⎯
⎯
⎯
H/L
PW-MOLD
3PIN
−40 to 85
1.2
3.5 Typ.
160
Typ.
Active
clamp
40 Min
⎯
⎯
⎯
⎯
H/L
TPS
3PIN
up to 40
2.0
(t = 10 s)
(mounted
on board)
1 Min
160
Typ.
Active
clamp
40 Min
⎯
⎯
⎯
⎯
H/L
SOP-8PIN
VDS(DC) 50 V
IO 8 A
RDS(ON) = 0.065 Ω Max
up to 18
50
(Tc=25°C)
8 Min
160
Typ.
Active
clamp
50 Min
⎯
⎯
⎯
⎯
H/L
TO-220SM
3PIN
VDS(DC) 20 V
IO 3 A
RDS(ON) = 0.4 Ω Max
up to 20
2.0
(t = 10 s)
(mounted
on board)
3 Min
160
Typ.
Active
clamp
40 Min
⎯
⎯
⎯
⎯
H/L
SOP-8PIN
160
Typ.
○
○
○
6 Typ.
⎯
DIAG
L
DIAG
H
DIAG
L
⎯
H/H
SOP-8PIN
160
Typ.
○
○
○
12 Typ.
⎯
DIAG
L
DIAG
H
DIAG
L
⎯
H/H
SOP-8PIN
2.0
(t = 10 s)
(mounted
on board)
1.5 Min
160
Typ.
Active
clamp
40 Min
⎯
⎯
⎯
⎯
H/L
SOP-8PIN
160
Typ.
Active
clamp
40 Min
⎯
⎯
⎯
⎯
H/L
TO-92MOD
3PIN
−40 to 110
30
−40 to 110
○
TPD1033F
High-side
switch
VDSS 60 V
IO 4 A
RDS(ON) = 0.22 Ω Max
TPD1034F
High-side
switch
VDSS 60 V
IO 8 A
RDS(ON) = 0.08 Ω Max
TPD1036F
2-ch low-side
switch
VDS(DC) 30 V
IO 1.5 A
RDS(ON) = 0.5 Ω Max
TPD1037BS
Low-side
switch
VDS(DC) 40 V
IO 1.5 A
RDS(ON) = 0.25 Ω Max
up to 40
−40 to 85
0.9
In-rush
10 Typ.
Shorted
load
3 Typ.
TPD1038F
High-side
switch
VDSS 60 V
IO 3 A
RDS(ON) = 0.12 Ω Max
6 to 18
−40 to 110
1.1
(mounted
on board)
3 Min
150
Min
Active
clamp
50 Min
TPD1039F
Low-side
switch
VDS(DC) 45 V
IO 1.5 A
RDS(ON) = 0.25 Ω Max
up to 45
−40 to 85
1.1
(mounted
on board)
5 Typ.
125
Min
TPD1039S
Low-side
switch
VDS(DC) 45 V
IO 1.5 A
RDS(ON) = 0.25 Ω Max
up to 45
−40 to 85
0.9
5 Typ.
TPD1042F
High-side
switch
VDSS 60 V
IO 7 A
RDS(ON) = 0.18 Ω Max
6 to 18
−40 to 115
1.1
(mounted
on board)
TPD1044F
Low-side
switch
VDS(DC) 41 V
IO 1 A
RDS(ON) = 0.6 Ω Max
up to 41
−40 to 125
** TPD1045F
Low-side
switch
VDS(DC) 50 V
IO 5 A
RDS(ON) = 0.1 Ω Max
up to 18
−40 to 125
150
5 to 18
up to 30
2.4
(t = 10 s)
(mounted
on board)
○
○
○
DIAG
L
DIAG
H
DIAG
L
⎯
H/H
SOP-8PIN
Active
clamp
45 Min
⎯
⎯
⎯
⎯
H/L
SOP-8PIN
125
Min
Active
clamp
45 Min
⎯
⎯
⎯
⎯
H/L
TO-92MOD
3PIN
7 Min
150
Min
⎯
0.9
(mounted
on board)
1 Min
160
Typ.
1.1
(mounted
on board)
5 Min
170
Typ.
○
○
○
DIAG
L
DIAG
H
DIAG
L
⎯
H/H
SOP-8PIN
Active
clamp
41 Min
⎯
⎯
⎯
⎯
H/L
PS-8
Active
clamp
50 Min
⎯
⎯
⎯
⎯
H/L
SOP-8PIN
**: Under development
122
Part Number
Use/Function
Outline
Operating
Junction
Protective Functions
Operating
Power
Supply
(Channel)
Over
Temperature
Dissipation Overcurrent
Overvoltage
Voltage
Temperature
Temperature
Topr (°C)
PD (W)
IS (A)
VS (V)
(V)
Tj (°C)
TS (°C)
— TPD2004F
Air bag
VBB=4 to 25
2-ch squib
VBB 30 V
VCC=4.75
=
Ω
RDS(ON) 1 Max
driver
to 5.25
(high-side SS)
— TPD2005F
8-ch high-side
switch
VDD 45 V
IO 1 A
RDS(ON) = 1.2 Ω Max
— TPD2007F
8-ch low-side
switch
Input/
Output
Package
When
1) Squib-short, short-to-battery,
short-to-ground and open-circuit detection LSD = L
2) When an abnormal condition is diagnosed,
and
SSOP-24PIN
the safing sensor is turned on.
HSD = H,
3) Diagnosis performed on squib driver’s
squib
internal MOSFET
ignites.
⎯
⎯
8 to 40
0.8
1.0 Min
160
Typ.
⎯
⎯
⎯
⎯
⎯
H/H
SSOP-24PIN
VDS(DC) 40 V
IO 1 A
up to 40
RDS(ON) = 1.4 Ω Max
0.8
1.0 Min
160
Typ.
Active clamp
40 Min
⎯
⎯
⎯
⎯
H/L
SSOP-24PIN
0.5
VDS monitor
1.0 V
Typ.
⎯
Active clamp
35 V Typ.
{
DIAG
L
DIAG
H
⎯
⎯
0.8
Adjustable
⎯
(Undervoltage
Overcurrent
detected at
4.5 V Max)
⎯
⎯
⎯
H/H
SSOP-24PIN
⎯
{
FAULT
H
(and
undervoltage)
H/H
SSOP-24PIN
⎯
{
FAULT
H
(and
undervoltage)
H/H
SSOP-24PIN
⎯
{
FAULT
H
(only under
voltage)
H/H
SSOP-24PIN
−40 to 85
2-ch high-side
Power MOSFET
driver
(with built-in
charge pump)
VDD 30 V
Source current
0.1 A Typ.
Sink current
0.1 A Typ.
8 to 18
— TPD7201F
3-phase
full-bridge
Power MOSFET
driver
(with built-in
charge pump)
VDD 30 V
Source current
1 A Max
Sink current
1 A Max
— TPD7202F
H bridge
Power MOSFET
driver
(with built-in
charge pump
VDD 30 V
Source current
1 A Max
Sink current
1 A Max
— TPD7203F
3-phase
full-bridge
Power MOSFET
driver
(with built-in
charge pump)
VDD 30 V
Source current
1 A Max
Sink current
1 A Max
— TPD7100F
Over
Open
Overvoltage
load Temperature
⎯
VDH=8 to 18
VDL=4.5
to 5.5
driver
Short
load
0.8
VDH 25 V
Io 20 mA Max
4-ch low-side
— TPD7000AF Power MOSFET
Diagnostic Functions
−40 to 110
7 to 18
0.8
−40 to 125
0.8
⎯
⎯
⎯
{
22 V Typ.
(Undervoltage
detected at
6.0 V Typ.)
⎯
{
22 V Typ.
(Undervoltage
detected at
6.0 V Typ.)
⎯
⎯
⎯
⎯
{
7 to 18
H/H
SSOP-24PIN
(ENB=“H”)
{
150
7 to 18
{
0.8
⎯
⎯
(Undervoltage
detected at
6.0 V Typ.)
⎯
⎯
—: Dry-packed product
123
250 V/500 V Series
Part Number
Features
TPD4101K
Functions
Protective Functions
Over
Undervoltage
Overcurrent
temperature
Rating
Output Type
Package
High-voltage PWM
DC brushless
motor driver
250 V/±1 A
3-phase
full-bridge
Hall IC input, bootstrap circuit, PWM, 3-phase decoder
{
{
{
HZIP23
TPD4102K
High-voltage PWM
DC brushless
motor driver
500 V/±1 A
3-phase
full-bridge
Hall IC input, bootstrap circuit, PWM, 3-phase decoder
{
{
{
HZIP23
TPD4103K
High-voltage PWM
DC brushless
motor driver
500 V/±1 A
3-phase
full-bridge
6-input, low-side driver, high-side driver
{
{
{
HZIP23
TPD4103AK
High-voltage PWM
DC brushless
motor driver
500 V/±1 A
3-phase
full-bridge
6-input, low-side driver, high-side driver
⎯
{
{
HZIP23
TPD4104K
High-voltage PWM
DC brushless
motor driver
500 V/±2 A
3-phase
full-bridge
6-input, low-side driver, high-side driver
{
{
{
HZIP23
TPD4104AK
High-voltage PWM
DC brushless
motor driver
500 V/±2 A
3-phase
full-bridge
6-input, low-side driver, high-side driver
⎯
{
{
HZIP23
** TPD4105K
High-voltage PWM
DC brushless
motor driver
500 V/±3 A
3-phase
full-bridge
6-input, low-side driver, high-side driver
{
{
{
HZIP23
** TPD4105AK
High-voltage PWM
DC brushless
motor driver
500 V/±3 A
3-phase
full-bridge
6-input, low-side driver, high-side driver
⎯
{
{
HZIP23
** TPD4111K
High-voltage PWM
DC brushless
motor driver
250 V/±1 A
3-phase
full-bridge
Hall amplifier input, bootstrap circuit, PWM, 3-phase decoder
{
{
{
HZIP23
** TPD4112K
High-voltage PWM
DC brushless
motor driver
500 V/±1 A
3-phase
full-bridge
Hall amplifier input, bootstrap circuit, PWM, 3-phase decoder
{
{
{
HZIP23
**: Under development
124
Interface Drivers
Transistor Arrays
(Transistor Array/Interface Driver Series)
Part Number
Device Type
No. of Output Clamp Output Breakdown Output Current Input Resistor
Circuits
Diode
Voltage (V)
(mA)
(Ω)
Recommended
System Supply
Voltage (V)
Package
DIP16/SOP16
TD62001AP/AF
TD62002AP/AF
TD62003AP/AF
TD62004AP/AF
TD62006P/F
TD62008AP/AF
Darlington driver
7
{
50
500
NA
Any
Darlington driver
7
{
50
500
10.5 k + 7 VZ.D.
14 to 15
DIP16/SOP16
Darlington driver
7
{
50
500
2.7 k
5
DIP16/SOP16
Darlington driver
7
{
50
500
10.5 k
6 to 15
DIP16/SOP16
Darlington driver
6
{
22
150
20 k
6 to 20
DIP14/SOP14
Darlington driver
7
{
50
400
20 k
6 to 20
DIP16/SOP16
TD62064AP/AF/BP-1/BF
High-current darlington driver
4
{
50/50/80/80
1500
230
5
DIP16/
HSOP16
TD62074AP/AF
Isolated-type high-current darlington driver
4
50
1500
230
5
DIP16/
HSOP16
TD62081AP/AF
TD62082AP/AF
Darlington driver
8
{
50
500
NA
Any
DIP18/SOP18
Darlington driver
8
{
50
500
10.5 k + 7 VZ.D.
14 to 25
DIP18/SOP18
TD62083AP/AF/AFN
Darlington driver
8
{
50
500
2.7 k
5
DIP18/SOP18
SSOP18
TD62084AP/AF/AFN
Darlington driver
8
{
50
500
10.5 k
6 to 15
DIP18/SOP18
SSOP18
TD62101P/F
TD62103P/F
TD62104P/F
TD62105P/F
Darlington driver
7
25
500
NA
Any
DIP16/SOP16
Darlington driver
7
25
500
2.7 k
5
DIP16/SOP16
Darlington driver
7
25
500
10.5 k
6 to 15
DIP16/SOP16
Darlington driver
7
25
500
20 k
12 to 25
DIP16/SOP16
TD62107P/F
Darlington driver (with Enable pin)
4
{
45/35
750
LS-, TTLcompatible
5
DIP16/
HSOP16
TD62164AP/BP/AF/BF
High-current, low-saturation driver
4
{
50/80/50/80
700
2k
5 to 15
DIP16/
HSOP16
TD62304AP/AF/AFN
Low-input-active darlington driver
7
50
500
14 k
5
DIP16/SOP16
SSOP16
TD62305AP/AF/AFN
Low-input-active darlington driver
7
50
500
14 k + D.
5
DIP16/SOP16
SSOP16
TD62307P/F
Low-saturation driver
7
{
20
150
20 k
5 to 18
DIP16/SOP16
TD62308AP/AF/BP-1/BF
Low-input-active darlington driver
4
{
50/50/80/80
1500
4k
5
DIP16/
HSOP16
TD62309P/F
Low-saturation driver
6
{
20
700
2k
5
DIP16/
HSOP16
TD62318AP/BP/AF/BF
Low-input-active, low-saturation driver
4
{
50/80/50/80
700
4k
5
DIP16/
HSOP16
TD62381P/F/FN
Low-saturation driver
8
15
500
2.7 k
5 to 18
DIP18/SOP18
SSOP18
TD62382AP/AF/AFN
Low-input-active, low-saturation driver
8
50
50
14 k
5 to 18
DIP18/SOP18
SSOP18
TD62383P
TD62384AP/AF
TD62385AP/AF
TD62386AP/AF
Low-input-active, low-saturation driver
8
Low-input-active darlington driver
8
Low-input-active darlington driver
8
Low-input-active darlington driver
8
{
{
10
500
14 k + D.
5 to 18
DIP20
50
500
14 k
5 to 18
DIP18/SOP18
50
500
14 k + D.
5 to 18
DIP18/SOP18
50
500
14 k
5 to 7
DIP20/SOP20
125
Transistor Arrays
Part Number
(Transistor Array/Interface Driver Series) (continued)
Device Type
No. of Output Clamp Output Breakdown Output Current Input Resistor
Circuits
Diode
Voltage (V)
(mA)
(Ω)
Recommended
System Supply
Voltage (V)
Package
TD62387AP/AF/AFN
Low-input-active darlington driver
8
{
50
500
14 k + D.
5 to 7
DIP20/SOP20
SSOP20
TD62388AP/AF/AFN
Low-input-active darlington driver
8
{
50
500
14 k + D.
5 to 7
DIP20/SOP20
SSOP20
TD62501P/F
Single-transistor array (common-emitter)
7
35
200
NA
Any
DIP16/SOP16
TD62502P/F/FN
Single-transistor array (common-emitter)
7
35
200
10.5 k + 7 VZ.D.
14 to 25
DIP16/SOP16
SSOP16
TD62503P/F/FN
Single-transistor array (common-emitter)
7
35
200
2.7 k
5
DIP16/SOP16
SSOP16
TD62504P/F/FN
Single-transistor array (common-emitter)
7
35
200
10.5 k
6 to 15
DIP16/SOP16
SSOP16
TD62505P/F
TD62506P/F
TD62507P/F
TD62551S
TD62553S
TD62554S
TD62555S
TD62583AP/AF
TD62591AP
TD62592AP
TD62593AP/AFN
TD62594AP/AFN
TD62595AP/AF
TD62596AP/AF
Single-transistor array (common-collector)
7
35
−200
NA
Any
DIP16/SOP16
Single-transistor array (common-collector)
7
35
−200
2.7 k
5
DIP16/SOP16
Isolated-type single-transistor array
5
35
−200
NA
Any
DIP16/SOP16
Single-transistor array (common-emitter)
4
25
150
NA
Any
SIP9
Single-transistor array (common-emitter)
4
25
150
2.7 k
5
SIP9
Single-transistor array (common-emitter)
4
25
150
10.5 k
6 to 15
SIP9
Single-transistor array (common-emitter)
4
25
150
20 k
12 to 25
SIP9
Single-transistor array (common-emitter)
8
50
50
2.7 k
5
DIP18/SOP18
Single-transistor array (common-emitter)
8
50
200
NA
Any
DIP18
Single-transistor array (common-emitter)
8
50
200
10.5 k + 7 VZ.D.
14 to 25
DIP18
Single-transistor array (common-emitter)
8
50
200
2.7 k
5
DIP18/SSOP18
Single-transistor array (common-emitter)
8
50
200
10.5 k
6 to 15
DIP18/SSOP18
Single-transistor array (common-emitter)
8
{
50
200
NA
Any
DIP18/SOP18
Single-transistor array (common-emitter)
8
{
50
200
10.5 k + 7 VZ.D.
14 to 25
DIP18/SOP18
TD62597AP/AF/AFN
Single-transistor array (common-emitter)
8
{
50
200
2.7 k
5
DIP18/SOP18
SSOP18
TD62598AP/AF/AFN
Single-transistor array (common-emitter)
8
{
50
200
10.5 k
6 to 15
DIP18/SOP18
SSOP18
TD62601P/F
Threshold-free driver (inverted output)
6
20
10
1M
4 to 18
DIP16/SOP16
TD62602P/F
Threshold-free driver
(inverted output, open-collector)
6
20
10
1M
4 to 18
DIP16/SOP16
TD62603P/F
Threshold-free driver (non-inverted output)
6
20
10
1M
4 to 18
DIP16/SOP16
TD62604P/F
Threshold-free driver
(non-inverted output, open-collector)
6
20
10
1M
4 to 18
DIP16/SOP16
High breakdown voltage, source-type driver
6
60
−50
2.7 k
5
DIP14/SOP14
High breakdown voltage, source-type driver
6
60
−50
47 k
6 to 15
DIP16/SOP16
High breakdown voltage, source-type driver
6
60
−50
10 k
5
DIP16/SOP16
TD62708N
Source-type darlington driver
(with Enable pin)
8
40
−1800
NA
5
DIP24N
TD62781AP
Source-type darlington driver
(with pull-down resistor)
8
60
−50
10 k
5
DIP18
TD62782F
Source-type darlington driver
(with pull-down resistor)
8
35
−50
20 k
6 to 15
SOP18
TD62783AP/AF/AFN
Source-type darlington driver
8
{
50
−500
10 k
5
DIP18/SOP18
SSOP18
TD62784AP/AF/AFN
Source-type darlington driver
8
{
50
−500
10 k
6 to 15
DIP18/SOP18
SSOP18
TD62785P/F
Source-type darlington driver
8
7
−500
5.6-k
pull-up
5
DIP18/SOP18
TD62703P/F
TD62705P/F
TD62706P/F
TD62786AP/AF/AFN
Source-type darlington driver
8
{
50
−500
14 k
5
DIP18/SOP18
SSOP18
TD62787AP/AF
Source-type darlington driver
8
{
50
−500
14 k + D.
5
DIP18/SOP18
126
(DMOS Array Series)
Part Number
Package
TB62003F/P
TB62004F/P
TB62006F/P
TB62007F/P
TB62008F/P
TB62009F/P
Use
Structure
SOP20/DIP20
8-bit DMOS driver
8-bit DMOS driver with inverter gate, 35 V / 200 mA
SOP20/DIP20
8-bit DMOS driver
8-bit DMOS driver with non-inverter gate, 35 V / 200 mA
SOP20/DIP20
8-bit DMOS driver
8-bit DMOS driver with NAND gate, 35 V / 200 mA
SOP20/DIP20
8-bit DMOS driver
8-bit DMOS driver with AND gate, 35 V / 200 mA
SOP20/DIP20
8-bit DMOS driver
8-bit DMOS driver with NOR gate, 35 V / 200 mA
SOP20/DIP20
8-bit DMOS driver
8-bit DMOS driver with OR gate, 35 V / 200 mA
(Multi-Chip Transistor Array Series)
Part Number
TD62M4700F
TD62M2701F
TD62M2702F
TD62M3600F
TD62M3601F
TD62M3700F
TD62M3701F
TD62M3702F
TD62M3704F
TD62M4500F
TD62M4501F
TD62M4503AFN
TD62M4600F
TD62M4601F
TD62M8500F
TD62M8501F
TD62M8600F
TD62M8601F
TD62M8603F
TD62M8604AF
Output Breakdown Voltage
(V)
Output Current
(A)
Package
2-ch push-pull driver, low-saturation type
10
±2.0
SSOP16
2-ch push-pull driver, low-saturation type
10
±2.0
SSOP16
2-ch push-pull driver, low-saturation type
10
±2.0
SSOP16
3-ch source driver, low-saturation type
10
−2.0
SSOP10
3-ch source driver, low-saturation type
30
−1.5
SSOP10
3-ch push-pull driver, low-saturation type
30
±1.5
SSOP16
3-ch push-pull driver, low-saturation type
10
±2.0
SSOP16
3-ch push-pull driver, low-saturation type
15
±2.0
SSOP16
3-ch push-pull driver, low-saturation type
10
−0.4
SSOP16
4-ch sink driver, low-saturation type
10
2.0
SSOP16
4-ch sink driver, low-saturation type
20
2.0
SSOP16
4-ch power MOSFET sink driver + diode
60
0.8
SSOP24 (0.65 mm)
4-ch source driver, low-saturation type
10
−2.0
SSOP16
4-ch source driver, low-saturation type
20
−2.0
SSOP16
8-ch sink driver, low-saturation type
10
2.0
HSOP16
8-ch sink driver, low-saturation type
20
2.0
HSOP16
8-ch source driver, low-saturation type
10
−2.0
HSOP16
8-ch source driver, low-saturation type
20
−2.0
HSOP16
8-ch source driver, low-saturation type
30
−1.5
HSOP16
8-ch source driver, low-saturation type
50
−2.0
HSOP16
Device Type
127
LED Driver ICs
(LED Panel Driver ICs)
Part Number
TB62702P/F
TB62705CP/CF/CFN
TB62706BN/BF
TB62707F
TB62708N
TB62709N/F
TB62710P/F/FN
Package
Use
Structure
DIP20/SOP20
10-segment display
10-bit DMOS sink driver (SIPO, latch), 30 V/30 mA
DIP16/SSOP16
Small LED panel
8-bit constant-current sink driver (SIPO, latch), 17 V/90 mA
SDIP24N/SSOP24
Large LED panel
16-bit constant-current sink driver (SIPO, latch), 17 V/90 mA
SSOP24
Full-color LED panel
8-bit constant-current sink driver (PIPO, latch), 17 V/90 mA
SDIP30N
Large LED panel
16-bit constant-current source driver (SIPO, latch), 17 V/−90 mA
SDIP24N/SSOP24
7-segment display
4-digit 7-segment display (anode common) decoder + constant-current driver (SIPO),
17 V/50 mA, −400 mA/digit
DIP20/SSOP24/SSOP20
Small LED panel
8-bit constant-current source driver (SIPO, latch), 17 V/−90 mA
TB62713N/F
SDIP24N/SSOP24
7 × 5 dot display
7 × 5 dot display (common cathode rows) decoder + constant-current driver (SIPO),
17 V/60 mA, −420 mA/digit
TB62715FN
TB62717N/F
TB62718AF
SSOP20
Small LED panel
8-bit constant-current sink driver (SIPO, latch), 17 V/150 mA
SDIP42N/QFP48
Full-color LED panel
24-bit constant-current sink driver (SIPO, latch), 17 V/50 mA
HQFP64
Full-color LED panel
PWM control 256-level gray scale + current compensation, 16-bit constant-current sink driver, 26 V/80 mA
TB62719AF
HQFP64
Full-color LED panel
PWM control 256-level gray scale + current compensation, 16-bit constant-current sink driver, 26 V/80 mA
(upward compatible with the TB62718AF)
DIP16/SSOP16/SSOP16
Small LED panel
3.3-V to 5-V drive, 8-bit constant-current sink driver (SIPO, latch), 17 V/90 mA
SDIP24N/SSOP24
Large LED panel
3.3-V to 5-V drive, 16-bit constant-current sink driver (SIPO, latch), 17 V/90 mA
Full-color LED panel
16-bit constant-current sink driver with current compensate (SIPO, latch), 17 V/60 mA
TB62725BP/BF/BFN
TB62726AN/AF
TB62727FN
SSOP30
SIPO: Serial-in parallel-out
PIPO: Parallel-in parallel-out
Toshiba manufactures the products in bold in the factories in Malaysia and Thailand as well as in Japan. We ship the products from the factories for overseas assembly of end products.
(White LED Driver ICs)
Part Number
TB62731FUG
TB62732FUG
** TB62733FTG
TB62734FMG
** TB62735FTG
** TB62736FUG
** TB62737FUG
Package
Use
Structure
SOT23-6pin
White color LED back light driver
Constant current step-up DC/DC converter
(output: 320 mW, efficiency: 80%, maximum output voltage: 30 V, maximum switching current: 0.3 A)
VQON24
White color LED back light driver
Charge-pump type DC/DC converter (2ch output), output current: 200 mA
SON8
White color LED back light driver
Constant current step-up DC/DC converter, efficiency: 85% (max), output: 600 mW,
(with over voltage protection function)
QFN16
White color LED back light driver
Charge-pump DC/DC converter + constant-current driver (4ch)
SOT23-6pin
White color LED back light driver
Constant current step-up DC/DC converter, efficiency: 85% (max)
SOT23-6pin
White color LED back light driver
Constant current step-up DC/DC converter, efficiency: 85% (max), (with over voltage protection function)
**: Under development
CCD Clock Driver ICs (CCD Clock Driver ICs)
Part Number
TB62801F
TB62802F
Package
Use
Structure
HSOP16
CCD linear image sensor
Linear CCD clock driver
HSOP16
CCD linear image sensor
Linear CCD clock driver (EMI noise measures product)
Thermal Head Driver ICs
Part Number
TD62C805F
TD62C851P
TD62C852P
TD62C854AF
TB62600F
128
Package
Device Type
Structure
QFP80
48-bit TPH driver
8-bit parallel input, 6-stage shift register latch drivers (30 V / 100 mA)
DIP20
8-bit solenoid driver
8-bit shift register latch drivers (50 V / 200 mA)
DIP20
8-bit solenoid driver
8-bit shift register latch drivers (50 V / 500 mA)
SSOP24
8-bit LED driver
With Power ON Reset, 8-bit shift register latch drivers (50 V / 500 mA)
QFP100
64-bit TPH driver
8-bit parallel input, 8-stage (1 bit input, 64-stage) shift register latch drivers (30 V / 130 mA)
Vending Machine Driver ICs
Part Number
Package
Use
Structure
Power supply monitor level: 92% of 5 V or less
Built-in resistor for reset timer
TD62650F
TD62651F
SSOP30 (1.0 mm)
Vending machine system driver
5-V power supply and power supply monitor +
24-V communications interface IC
Power supply monitor level: 85% of 5 V or less
With external resistor for timer reset
Power supply monitor level: 92% of 5 V or less
With external resistor for timer reset
TD62652F
Other Driver ICs
Part Number
TD62930P/F
TD62C854F
TD62C854AF
Package
DIP16/SSOP16 (1.0 mm)
SSOP24 (1 mm)
SSOP24 (1 mm)
Use
IGBT gate driver for home appliances (inverters)
General purpose use
Structure
3-ch small-signal push-pull driver (30 V/± 100 mA)
8 outputs darlington driver
8 outputs darlington driver with Power ON Reset
129
Motor Drivers
Brush Motor Driver ICs
Part Number
(Bridge Driver ICs)
Package
Features
TA7354P
TA7257P
TA7267BP
TA7279AP/P
SIP9
IOUT = 0.2 A (avg), 0.6 A (peak), built-in diode, 4 modes
HSIP7
IOUT = 1.5 A (avg), 4.5 A (peak), built-in diode, 4 modes
HSIP7
IOUT = 1.0 A (avg), 3.0 A (peak), built-in diode, 4 modes
HDIP14
2-channel 4-mode driver, IOUT = 1.0 A (avg), 3.0 A (peak), built-in diode, built-in thermal shutdown circuit
TA7288P
HSIP10
Sequential dual driver with Vref, IOUT = 1.0 A (avg), 2.0 A (peak), built-in diode, 4 modes, built-in thermal shutdown circuit/output pin protection circuit,
built-in shoot through current protection circuit, hysteresis for all inputs
TA8400P
DIP16
Sequential dual driver with Vref A and Vref B, IOUT = 1.0 A (peak), built-in diode, 4 modes, built-in thermal shutdown circuit,
built-in shoot through current protection circuit, hysteresis for all inputs
TA8405S
SIP9
Sequential dual driver, IOUT = 1.0 A (peak), built-in diode, 4 modes, built-in thermal shutdown circuit, built-in shoot through current protection circuit,
hysteresis for all inputs
TA8409S
TA8409F
SIP9
TA7291P
HSIP10
4-mode driver, IOUT = 1.0 A (avg), 2.0 A (peak), built-in diode, with Vref, VCC (max) = 25 V (P)/30 V (AP),
built-in thermal shutdown circuit/output pin protection circuit, built-in standby circuit, hysteresis for all inputs
TA7291S
SIP9
4-mode driver, IOUT = 0.4 A (avg), 1.2 A (peak), built-in diode, with Vref, VCC (max) = 25 V (S)/30 V (AS),
built-in thermal shutdown circuit/output pin protection circuit, built-in standby circuit, hysteresis for all inputs
TA7291F
HSOP16
4-mode driver, IOUT = 0.4 A (avg), 1.2 A (peak), built-in diode, with Vref, VCC (max) = 25 V (F)/30 V (AF),
built-in thermal shutdown circuit/output pin protection circuit, built-in standby circuit, hysteresis for all inputs
TA8428K
TA8428F
TA8429H
TD62M4700F
TA7733F
TA8401F
HSIP7
4-mode driver, IOUT = 1.5 A (avg), 3.0 A (peak), VCC (max) = 30 V, built-in diode, built-in thermal shutdown circuit/overcurrent protection circuit
HSOP20
4-mode driver, IOUT = 0.8 A (avg), 2.4 A (peak), VCC (max) = 30 V, built-in diode, built-in thermal shutdown circuit/overcurrent protection circuit
HZIP12
4-mode driver, IOUT = 3.0 A (avg), 4.5 A (peak), VCC (max) = 30 V, built-in thermal shutdown circuit/overcurrent protection circuit, HZIP power package
SSOP16
Ultra-low voltage, low-saturation voltage type, IOUT = 2.0 A
SSOP16
Low-voltage use (VCC (min) = 1.8 V), IOUT = 0.5 A, 4 modes, wide operating voltage range, can be used as interface driver, high-efficient drive
SSOP16
Low-voltage use (VCC (min) = 3.0 V), IOUT = 0.5 A, 4 modes, wide operating voltage range, can be used as interface driver, high-efficient drive
TA8440H
HZIP12
Bridge H switch 50 V, IOUT = 1.5 A (avg), 3.0 A (peak), driver with phase-chopper pin, 4 modes, built-in diode, built-in thermal shutdown circuit,
CMOS compatible input
—
TA8482FN
SSOP30
Bridge driver + sensor amp in a single chip, VCC (min) = 2.7 V, IOUT = 0.6 A (peak), 4 modes, built-in current limiter, built-in thermal shutdown circuit,
built-in tape top/end sensor amp
—
TA8496FL
QON24
Constant-current operation, IOUT = 20 mA, built-in low-noise high-gain amp, magnetic head read/write IC for cameras,
writing and detecting of magnetic recording signals
TB6501P
TB6524FN
TB6549P/PG
TB6549F/FG
DIP16
H switch 25 V with rotation detector, 1 A, with Vref, 4 modes, rotation detection using back-EMF, built-in thermal shutdown circuit, output voltage control
SSOP16
2-channel driver, IOUT = 0.1 A, constant-current operation possible (VCC = 2.0 V to 7.0 V), 3 modes, built-in diode, Enable pin
DIP16
PWM control bridge driver, IOUT (max) = 3.5 A, VCC (max) = 30 V, 4 modes, PWM control, standby function,
built-in thermal shutdown (TSD) circuit/overcurrent protection circuit
** TB6549HQ
SSOP10
HSOP20
4-mode driver, IOUT = 0.4 A (avg), 1.0 A (peak), VCC (max) = 25 V, built-in diode, built-in thermal shutdown circuit, built-in standby circuit, hysteresis for all inputs
HZIP25
PWM control bridge driver, IOUT (max) = 4.5 A, VCC (max) = 30 V, 4 modes, PWM control, standby function,
built-in thermal shutdown (TSD) circuit/overcurrent protection circuit
PWM chopper type, constant-current dual DC motor driver, 40 V/8.0 A (peak), 4 modes, constant-current PWM control, standby function,
built-in thermal shutdown (TSD) circuit/overcurrent protection circuit
—
TB62300F
HSOP-36-0.65
—
—
—
—*
—*
TB6552FL/FLG
TB6552FN/FNG
TB6592FL/FLG
TB6555FLG
TB6595FLG
QON24
2-ch PWM bridge driver, 1.5 V/0.8 A (peak), 4 modes, standby function, built-in thermal shutdown (TSD) circuit, direct PWM control
SSOP16
2-ch PWM bridge driver, 1.5 V/0.8 A (peak), 4 modes, standby function, built-in thermal shutdown (TSD) circuit, direct PWM control
QON24
2-ch PWM bridge driver, 6 V/0.8 A (peak), 4 modes, standby function, built-in thermal shutdown (TSD) circuit, direct PWM control
—
—
QON36
4-ch PWM bridge driver, 15 V/0.8 A (peak), 4 modes, standby function, built-in thermal shutdown (TSD) circuit, direct PWM control
QON36
4-ch PWM bridge driver, 6 V/0.8 A (peak), 4 modes, standby function, built-in thermal shutdown (TSD) circuit, direct PWM control
TB6591FL/FLG
QON48
7-ch PWM bridge driver (6-ch full-bridge driver + 1-ch constant-current bridge driver), 6.0 V/0.8 A (peak), 4 modes, output PWM control, standby function,
built-in thermal shutdown (TSD) circuit
TB6557FLG
QON36
6-ch PWM bridge driver, 15 V/0.8 A (peak), 4 modes, standby function, built-in thermal shutdown (TSD) circuit, direct PWM control,
built-in serial interface decoder with 6 bit EVR DAC, weight register
—** TB6558FLG
QON24
2-ch PWM chopper type, constant-current driver, 15 V/0.8 A (peak), 4 modes, constant-current PWM control, standby function,
built-in thermal shutdown (TSD) circuit
SDIP24
2-ch PWM bridge driver, 40 V/1.5 A (peak), 4 modes, on-chip VDD (5 V) regulator for internal circuit, constant-current PWM control, standby function,
built-in thermal shutdown (TSD) circuit
** TB6561NG
—: Dry-packed product
130
*: New product
**: Under development
(Power Op-Amp)
Circuit
Dual
Part Number
TA7256P
TA7272P
Package
Maximum Ratings
IO (A)
VCC (V)
Remarks
HSIP10
±18
0.5
Internally phase-corrected type
HSIP10
±18
1.2
Internally phase-corrected type
131
Brushless Motor Driver ICs
Part Number
TA7712P
TA7712F
TA7713P
TB6539N
TB6539F
TB6551F
TB6556F
* TB6581HG
TA7259P
TA7259P(LB)
TA7259F
TA7262P
TA7262P(LB)
TA7262F
TA7736P
TA7736F
TA7745P
TA7745F
TA8416F
TA8423P
TA8423F
TA8424F
TA8463F
TA8466AF
TA8470AF
TA8483CP
TA84005F
TA84006F
TA8486F
TA8490AF
TA8492P
TA8493F
TA8493AF
TA8493BF
TA8499F
— TB6519F
— TB6525F
— TB6534F
TB6520P
TB6537P/F
TB6548F
* TB6575FNG
Package
(3-phase Controllers/Drivers)
Maximum Ratings
VO (V)
IO (A)
DIP20
0.025
SSOP24
0.025
8
DIP20
0.025
8
Features
8
General-purpose motor driver, external transistor system, 3-phase full-wave driver, rotation signal output function, brake function
SDIP24
0.02
18
SSOP30
0.02
18
SSOP24
0.002
12
SSOP30
0.002
12
3-phase full-wave sine-wave current PWM controller, automatic lead angle control
HZIP25
2.0
500
3-phase full-wave sine-wave PWM brushless driver, multi-chip package of sine-wave controller and TPD4103AK
HDIP14
1.2
26
HSOP14
1.2
26
HSOP20
1.2
26
HDIP14
1.5
25
HSOP14
1.5
25
HSOP20
1.5
25
DIP16
1.0
26
HSOP16
1.0
26
DIP16
1.0
18
SSOP16
1.0
18
SSOP16
0.7
8
DIP16
1.2
18
HSOP16
1.2
18
HSOP20
1.2
18
3-phase full-wave driver, Low-noise drive, built-in FG amp
HQFP30
0.6
8
3-phase full-wave driver, digital servo, Low-noise drive, built-in index amp
3-phase full-wave sine-wave current PWM controller
3-phase full-wave driver, current control type
3-phase full-wave driver, voltage control type
3-phase full-wave driver, current control type
3-phase full-wave/half-wave driver, voltage control type, suitable for low-voltage use
3-phase full-wave/half-wave driver, suitable for low-voltage use, 2 hall sensor drive
3-phase full-wave driver, 1-terminal input control, current control type, built-in reference voltage circuit for control amp
HSOP16
0.7
18
3-phase full-wave driver, 1-terminal input control, Low-noise drive, semi-linear type, reduced external parts
HSOP20
1.2
18
Low-noise drive, built-in FG amp
HDIP14
2.0
35
3-phase full-wave driver, PWM sensorless drive with the TB6520P
SSOP30
1.0
25
3-phase full-wave driver, PWM sensorless drive with the TB6548F
SSOP30
1.0
25
3-phase full-wave driver
SSOP24
2.0
15
Low-saturation voltage multi-chip transistor array, 3-phase + H bridge
SSOP30
1.2
16
CD-ROM spindle motor driver
3-phase full-wave driver, voltage control type
DIP16
1.5
20
SSOP30
1.2
16
SSOP30
1.2
16
SSOP30
1.2
16
SSOP30
1.2
16
QFP64 (0.5 mm)
0.01
14
QFP64 (0.5 mm)
0.015
8
Movie cylinder motor and loading motor controller
QFP64 (0.5 mm)
0.01
12
Movie cylinder motor and capstan motor controller
DIP16
DIP18/SSOP24
0.0002
7
0.02
5.5
CD-ROM spindle motor driver, direct PWM control system
Movie cylinder motor and capstan motor controller
PWM type, sensorless motor controller, VCC = 5 V, with TA8483CP
PWM type, sensorless motor controller, VCC = 5 V, external transistor system
SSOP24
0.02
5.5
PWM type, sensorless motor controller, VCC = 5 V, with TA84005F
SSOP24 (0.65 mm)
0.02
5.5
PWM type, sensorless motor controller, analog speed control input, function to improve startup
—: Dry-packed product
*: New product
(2-phase Fan Driver Controllers)
Part Number
TA8420AF
TA8421AF
TA8462F
TA8473F
TA8473FN
132
Package
Maximum Ratings
VO (V)
IO (A)
Features
SSOP10
2.0
15
Fan motor driver, with FG output
SSOP10
2.0
15
Fan motor driver, with motor status detection pin
SSOP10
1.5
15
Fan motor driver, with FG output and motor status detection pin
SSOP16
1.2
13.8
SSOP16 (0.65 mm)
1.2
13.8
Fan motor driver, variable speed type, with radio noise reduction pin
Stepping Motor Driver ICs (Bipolar)
Part Number
TA8411L
TB6500AH
TA8435H
TB62201AF
TB62202AFG
TB62205FG
TB62206FG
Package
Maximum Ratings
VO (V)
IO (A)
Features
HDIP24
0.8
30
HZIP25
0.8
30
HZIP25
1.5
40
Pseudo sine-wave drive (PWM chopper type), reset and monitor pins, built-in micro-step decoder, clock input
HSOP-36-0.65
1.5
40
Pseudo sine-wave drive (PWM chopper type), dual-stepping motor driver
HSOP-36-0.65
1.0
40
Pseudo sine-wave drive (PWM chopper type), dual-stepping motor driver
HSOP-36-0.65
0.7
30
Built-in 2-ch step-down DC/DC converter, pseudo sine-wave drive (PWM chopper type), on-chip VDD(5 V) regulator for internal circuit
HSOP20-1.00
1.8
40
PWM chopper type, phase input, 2-phase/1-2 phase excitation
—* TB62207BFG
HSOP-36-0.65
8.0
37
Pseudo sine-wave drive (PWM chopper type), dual-stepping motor driver
Built-in 2-ch step-down DC/DC converter, on-chip VDD(5 V) regulator for internal circuit
—
HSOP-36-0.65
1.8
40
Pseudo sine-wave drive (PWM chopper type), built-in micro-step decoder, clock input
—
—
—
TB62209FG
Serial input system driver for fax machines and printers
—** TB62217AFG
THQFP64
8.0
50
Pseudo sine-wave drive (PWM chopper type), dual-stepping motor driver
Built-in 3-ch step-down DC/DC converter, on-chip VDD(5 V) regulator for internal circuit
TB6504F
TB6512AF
TB6526AF
TA8430AF
TA84002F
TA7289P
TA7289F
TA7774P
TA7774F
—** TB6598FNG
** TB6562ANG
SSOP24
0.15
18
Pseudo sine-wave drive (PWM chopper type), reset and monitor pins, built-in micro-step decoder, clock input
SSOP24
0.12
12
Pseudo sine-wave drive (PWM chopper type), reset and monitor pins
SSOP24
0.12
10
Pseudo sine-wave drive (PWM chopper type), reset and monitor pins, built-in micro-step decoder, external PNP transistor
HSOP16
0.6
8
2-phase bipolar stepping motor driver, with Enable and output voltage adjustment pins
HSOP20
1.0
35
Bipolar PWM chopper type, phase input, 2-phase/1-2 phase excitation
HDIP14
1.5
30
HSOP20
0.7
30
DIP16
0.4
17
HSOP16
0.4
17
Bipolar PWM chopper type, built-in 4-bit DA conversion
2-phase bipolar drive, switchable power supply system
SSOP16
0.8
15
PWM chopper type, phase input, 2-phase/1-2 phase excitation
SDIP24
1.5
40
PWM chopper type, phase input, 2-phase/1-2 phase excitation, on-chip VDD (5 V) regulator for internal circuit
—: Dry-packed product
*: New product
**: Under development
(Unipolar)
Part Number
TD62064AP/AF
TD62064BP-1/BF
TD62107P
TD62164AP/AF
TD62164BP/BF
TD62308AP/AF
TD62308BP-1/BF
TD62318AP/AF
TD62318BP/BF
TA8415P
Package
Maximum Ratings
VO (V)
IO (A)
Features
DIP16/HSOP16
1.5
50
NPN darlington transistor array containing 4 circuits, with clamp diode, active-High
DIP16/HSOP16
1.5
80
NPN darlington transistor array containing 4 circuits, with clamp diode, active-High
DIP16
0.75
45
NPN darlington transistor array containing 4 circuits, with clamp diode and Enable pin
DIP16/HSOP16
0.7
50
NPN single transistor array containing 4 circuits, with clamp diode, active-High
DIP16/HSOP16
0.7
80
NPN single transistor array containing 4 circuits, with clamp diode, active-High
DIP16/HSOP16
1.5
50
NPN darlington transistor array containing 4 circuits, with clamp diode, active-Low
DIP16/HSOP16
1.5
80
NPN darlington transistor array containing 4 circuits, with clamp diode, active-Low
DIP16/HSOP16
0.7
50
NPN single transistor array containing 4 circuits, with clamp diode, active-Low
DIP16/HSOP16
0.7
80
NPN single transistor array containing 4 circuits, with clamp diode, active-Low
DIP16
0.4
28
Capable of 1-phase, 2-phase and 1-2 phase excitation of 3-phase/4-phase motors, unipolar system, clock input
(5-phase Controller)
Part Number
TB6528P
Package
DIP24
Maximum Ratings
IO (A)
VO (V)
0.03
20
Features
5-phase universal controller
133
Power Supply ICs
Point Regulators (LDO Regulators)
Point regulators are small regulator ICs which can be individually assigned to circuit blocks as necessary. These devices incorporate an ON/OFF control function,
which facilitates power management.
< Features >
• Small package
•
Built-in ON/OFF control function
• Low saturation voltage
•
Built-in overtemperature and overcurrent protection circuits
• Low noise
•
Capable to use a ceramic capacitor
• High ripple rejection
< Low-Dropout Voltage Regulator Series >
Single output power supply
TAR5S series
Dual output power supply
TAR5SB series
TAR8H series
TAR8D series
TAR5S**U series
(Single Output Type)
Part Number
(mm)
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
SMV
SMV
1.6
2.9
(mm)
TAR5S15U
TAR5S16U
TAR5S17U
TAR5S18U
TAR5S19U
TAR5S20U
TAR5S21U
TAR5S22U
TAR5S23U
TAR5S24U
TAR5S25U
TAR5S26U
TAR5S27U
TAR5S28U
TAR5S29U
TAR5S30U
TAR5S31U
TAR5S32U
TAR5S33U
TAR5S34U
TAR5S35U
TAR5S36U
TAR5S37U
TAR5S38U
TAR5S39U
TAR5S40U
TAR5S41U
TAR5S42U
TAR5S43U
TAR5S44U
TAR5S45U
TAR5S46U
TAR5S47U
TAR5S48U
TAR5S49U
TAR5S50U
TAR5S15
TAR5S16
TAR5S17
TAR5S18
TAR5S19
TAR5S20
TAR5S21
TAR5S22
TAR5S23
TAR5S24
TAR5S25
TAR5S26
TAR5S27
TAR5S28
TAR5S29
TAR5S30
TAR5S31
TAR5S32
TAR5S33
TAR5S34
TAR5S35
TAR5S36
TAR5S37
TAR5S38
TAR5S39
TAR5S40
TAR5S41
TAR5S42
TAR5S43
TAR5S44
TAR5S45
TAR5S46
TAR5S47
TAR5S48
TAR5S49
TAR5S50
IN
Rating
2.9
2.8
1.6
UFV
2.8
1.7
Output Voltage
(V)
2.1
2.0
OUT
CONTROL GND NOISE
Please ask your local retailer about the devices with other output voltage.
134
Power Dissipation
(mW)
(mm)
TAR5SB15
TAR5SB16
TAR5SB17
TAR5SB18
TAR5SB19
TAR5SB20
TAR5SB21
TAR5SB22
TAR5SB23
TAR5SB24
TAR5SB25
TAR5SB26
TAR5SB27
TAR5SB28
TAR5SB29
TAR5SB30
TAR5SB31
TAR5SB32
TAR5SB33
TAR5SB34
TAR5SB35
TAR5SB36
TAR5SB37
TAR5SB38
TAR5SB39
TAR5SB40
TAR5SB41
TAR5SB42
TAR5SB43
TAR5SB44
TAR5SB45
TAR5SB46
TAR5SB47
TAR5SB48
TAR5SB49
TAR5SB50
OUT
450
(UFV)
200
380
(SMV)
NOISE
Pin Configuration
♦: A result of an evaluation on a glass-epoxy board. (30 mm × 30 mm), Ta = 25°C
Output Current
(mA)
IN
GND
CONTROL
♦
(Dual Output Type)
TAR8H02K
TAR8H03K
TAR8H04K
TAR8H05K
TAR8H06K
TAR8D01K
TAR8D02K
TAR8D03K
Independent control
type
Output Current
(mA)
Ach
2.8
100
Bch
3.0
150
Ach
2.8
100
Bch
2.8
150
Ach
2.5
100
Bch
2.8
150
Ach
2.5
100
Bch
3.0
150
Ach
1.8
100
Bch
2.8
150
Ach
1.5
100
Bch
2.5
150
Ach
2.5
Bch
2.8
Ach
2.0
Bch
2.8
Ach
2.8
Bch
3.0
TAR8D04K
Ach
1.5
Bch
1.5
Ach
TAR8D05K
2.8
Bch
2.8
Ach
TAR8D06K
2.9
Bch
2.9
Ach
TAR8D07K
3.0
Bch
3.0
* TAR8D08K
Ach
2.8
Bch
2.85
♦
Power Dissipation
Internal Connection
Package
1. CONTROL
2. Noise(A)
3. Noise(B)
4. GND
5. VOUT(B)
6. VIN(B)
7. VIN(A)
8. VOUT(A)
2.0mm
8
400
2.3mm
TAR8H01K
Synchronous switch
type
Output Voltage
(V)
Part Number
3.1mm
Description
♦: A result of an evaluation on a glass-epoxy board. (30 mm × 30 mm), Ta = 25°C
The output voltage of A and B channels can be set from 1.5V to 5.0V at 0.1V intervals. (Semi-customization of the output voltage is supported.)
6
5
US8
1
100
7
2
3
4
1. Noise(A)
2. Noise(B)
3. CONTROL(A)
4. GND
5. CONTROL(B)
6. VOUT(B)
7. VIN
8. VOUT(A)
*: New product
135
Series Regulators
Positive-voltage output
Polarity
136
Part Number
TA7805F
TA78057F
TA7806F
TA7807F
TA7808F
TA7809F
TA7810F
TA7812F
TA7815F
TA7818F
TA7820F
TA7824F
TA7805S
TA78057S
TA7806S
TA7807S
TA7808S
TA7809S
TA7810S
TA7812S
TA7815S
TA7818S
TA7820S
TA7824S
TA7805SB
TA78057SB
TA7806SB
TA7807SB
TA7808SB
TA7809SB
TA7810SB
TA7812SB
TA7815SB
TA7818SB
TA7820SB
TA7824SB
TA78033LF
TA7804LF
TA7805LF
TA7807LF
TA7808LF
TA7809LF
TA78033LS
TA7804LS
TA7805LS
TA7807LS
TA7808LS
TA7809LS
TA78M05F
TA78M06F
TA78M08F
TA78M09F
TA78M10F
TA78M12F
TA78M15F
TA78M18F
TA78M20F
TA78M24F
Use/Function
Output
Output
Current
Voltage
(typ.) (V) (max) (mA)
Input Voltage
(max) (V)
Drop-out
Voltage
(typ.) (V)
5
Output
Bias
Power
Voltage
Current
Dissipation
Tolerance
(typ.) (mA)
(W)
(%)
Package
Equivalent
1.0
±4
(Ta = 25°C)
10
(Tj = 25°C)
(Tc = 25°C)
PW-MOLD
78XX
2.0
±4
(Ta = 25°C)
20
(Tj = 25°C)
(Tc = 25°C)
TO-220(NIS)
78XX
±4
1.8
(Tj = 25°C) (Ta = 25°C)
TPL
78XX
4.2
5.7
6
7
35
8
High-current output
Surface-mount PW-MOLD package
9
10
4.3
2.0
(IO = 1000 mA)
1000
12
15
4.4
18
4.5
40
20
4.6
24
5
4.2
5.7
6
7
35
8
High-current output
Isolation package
9
10
4.3
2.0
(IO = 1000 mA)
1000
12
15
4.4
18
4.5
40
20
4.6
24
5
4.2
5.7
6
7
High-current output
Radial tape packing for automatic
mounting
35
8
9
10
4.3
2.0
(IO = 1000 mA)
1000
12
15
4.4
18
4.5
40
20
4.6
24
3.3
4
High-current output
Surface-mount PW-MOLD package
5
7
1000
20
2.0
(IO = 1000 mA)
3.0
1.0
(Ta = 25°C)
±3
10
(Tj = 25°C)
(Tc = 25°C)
PW-MOLD
78XX
1000
20
2.0
(IO = 1000 mA)
3.0
2.0
±3
(Ta = 25°C)
(Tj = 25°C)
15
(Tc = 25°C)
TO-220(NIS)
78XX
1.0
(Ta = 25°C)
±4
10
(Tj = 25°C)
(Tc = 25°C)
PW-MOLD
78MXX
8
9
3.3
4
High-current output
Isolation package
5
7
8
9
5
4.5
6
8
Medium-current output
Surface-mount PW-MOLD package
10
12
4.6
35
9
1.7
(IO = 350 mA)
500
4.7
4.8
15
18
20
24
40
4.9
5.0
Positive-voltage output
Polarity
Part Number
TA78M05S
TA78M06S
TA78M08S
TA78M09S
TA78M10S
TA78M12S
TA78M15S
TA78M18S
TA78M20S
TA78M24S
TA78M05SB
TA78M06SB
TA78M08SB
TA78M09SB
TA78M10SB
TA78M12SB
TA78M15SB
TA78M18SB
TA78M20SB
TA78M24SB
TA78L005AP
TA78L006AP
TA78L007AP
TA78L075AP
TA78L008AP
TA78L009AP
TA78L010AP
TA78L012AP
TA78L132AP
TA78L015AP
TA78L018AP
TA78L020AP
TA78L024AP
TA78L05F
TA78L06F
TA78L07F
TA78L08F
TA78L09F
TA78L10F
TA78L12F
TA78L15F
TA78L18F
TA78L20F
TA78L24F
TA78L05PF
TA78L06PF
TA78L07PF
TA78L08PF
TA78L09PF
TA78L10PF
TA78L12PF
TA78L15PF
TA78L05S
TA78L07S
TA78L08S
TA78L09S
TA78L10S
TA78L12S
TA78L15S
Use/Function
Output
Output
Current
Voltage
(typ.) (V) (max) (mA)
Input Voltage
(max) (V)
Drop-out
Voltage
(typ.) (V)
5
8
12
4.6
35
9
10
Package
Equivalent
2.0
±4
(Ta = 25°C)
20
(Tj = 25°C)
(Tc = 25°C)
TO-220(NIS)
78MXX
±4
1.8
(Tj = 25°C) (Ta = 25°C)
TPL
78MXX
±4
0.8
(Tj = 25°C) (Ta = 25°C)
TO-92MOD
78LXX
±5
0.5
(Tj = 25°C) (Ta = 25°C)
PW-MINI
(SOT-89)
78LXX
1.3
(Ta = 25°C)
±4
Mounted on
(Tj = 25°C)
glass-epoxy
substrate
PS-8
78LXX
0.6
±4
(Tj = 25°C) (Ta = 25°C)
TO-92
78LXX
4.5
6
Medium-current output
Isolation package
Output
Bias
Power
Voltage
Current
Dissipation
Tolerance
(typ.) (mA)
(W)
(%)
1.7
(IO = 350 mA)
500
4.7
4.8
15
18
40
20
4.9
24
5.0
5
4.5
6
8
Medium-current output
Radial tape packing for automatic
mounting
10
12
4.6
35
9
1.7
(IO = 350 mA)
500
4.7
4.8
15
18
40
20
4.9
24
5.0
5
6
3.1
7
7.5
8
Low-current output
Radial tape packing for automatic
mounting
35
9
10
1.7
(IO = 150 mA)
150
12
3.2
13.2
15
3.3
18
40
20
24
3.5
5
6
3.1
7
8
Low-current output
Surface-mount
PW-MINI (SOT-89) package
35
9
10
1.7
(IO = 150 mA)
150
12
3.2
15
3.3
18
40
20
24
3.5
5
6
3.1
7
Low-current output
Small thin surface-mount PS-8 package
8
9
150
35
2.0
(IO = 150 mA)
10
3.2
12
15
5
3.1
7
Low-current output
Radial tape packing for automatic
mounting
8
9
10
100
35
1.7
(IO = 100 mA)
3.2
12
15
3.3
137
Series Regulators (continued)
Positive-voltage output (low dropout)
Polarity
Part Number
TA48015F
TA48018F
TA4802F
TA48025F
TA4803F
TA48033F
TA4805F
TA48018S
TA4802S
TA48025S
TA4803S
TA48033S
TA4805S
** TA48015AF
** TA48018AF
** TA48025AF
** TA48033AF
** TA4805AF
** TA4809AF
** TA48015AS
** TA48018AS
** TA48025AS
** TA48033AS
** TA4805AS
** TA4809AS
TA48M025F
TA48M03F
TA48M033F
TA48M0345F
TA48M04F
TA48M05F
TA78DM05S
TA78DM08S
TA78DM09S
TA78DM12S
** TA58L05F
** TA58L06F
** TA58L08F
** TA58L09F
** TA58L10F
** TA58L12F
** TA58L15F
TA58L05S
TA58L06S
TA58L08S
TA58L09S
TA58L10S
TA58L12S
TA58L15S
Use/Function
Output
Output
Current
Voltage
(typ.) (V) (max) (mA)
Input Voltage
(max) (V)
1.5
Drop-out
Voltage
(typ.) (V)
Output
Bias
Power
Voltage
Current
Dissipation
Tolerance
(typ.) (mA)
(W)
(%)
Package
1.0
(Ta = 25°C)
10
(Tc = 25°C)
PW-MOLD
±4.5
(Tj = 0
to 125°C)
2.0
(Ta = 25°C)
20
(Tc = 25°C)
TO-220(NIS)
±4
1.0
(Ta = 25°C)
10
(Tc = 25°C)
PW-MOLD
2.0
(Ta = 25°C)
20
(Tc = 25°C)
TO-220(NIS)
1.0
(Ta = 25°C)
10
(Tc = 25°C)
PW-MOLD
0.8 Max
1.8
High-current output
Low drop-out
Surface-mount PW-MOLD package
2
2.5
Equivalent
1000
16
3
0.5 Max
(IO = 500 mA)
0.8
(IO = 0 A)
±4.5
(Tj = 0
to 125°C)
3.3
High-current output
Low drop-out
Isolation package
5
1.8
2
2.5
3
3.3
5
1000
16
1.5
High-current output
Low drop-out
Surface-mount PW-MOLD package
1.8
2.5
3.3
5
9
High-current output
Low drop-out
Isolation package
0.8
(IO = 0 A)
0.8 Max
1000
16
1.5
1.8
2.5
3.3
5
9
0.5 Max
(IO = 500 mA)
0.5 Max
(IO = 500 mA)
0.8
(IO = 0 A)
(Tj = 0
to 125°C)
0.8 Max
1000
16
0.5 Max
(IO = 500 mA)
0.8
(IO = 0 A)
±4
(Tj = 0
to 125°C)
2.5
3
Medium-current output
Low drop-out
Surface-mount PW-MOLD package
Medium-current output
Low drop-out
Isolation package
Medium-current output
Low drop-out
Surface-mount PW-MOLD package
Medium-current output
Low drop-out
Isolation package
0.8
3.3
3.45
500
29
0.65 Max
(IO = 500 mA)
4
0.9
5
1.0
(IO = 0 A)
5
0.8
8
9
500
29
(load dump = 60 V)
0.75 Max
(IO = 500 mA)
0.9
12
1.0
(IO = 0 A)
5
0.45
6
0.5
8
0.55
9
10
250
29
(load dump = 60 V)
0.4 Max
(IO = 200 mA)
0.6
0.6
12
0.65
15
0.75
(IO = 0 A)
5
0.45
6
0.5
8
0.55
9
10
250
29
(load dump = 60 V)
0.4 Max
(IO = 200 mA)
0.6
0.6
12
0.65
15
0.75
(IO = 0 A)
±5
(Tj = 0
to 125°C)
2.0
±6
(Ta = 25°C)
(Tj = 25°C)
20
(Tc = 25°C)
±4
(Ta = −40
to 105°C)
±4
(Ta = −40
to 105°C)
TO-220(NIS)
1.0
(Ta = 25°C)
10
(Tc = 25°C)
PW-MOLD
2.0
(Ta = 25°C)
20
(Tc = 25°C)
TO-220(NIS)
**: Under development
138
Negative-voltage output
Positive-voltage output (low dropout)
Polarity
Part Number
TA48L018F
TA48L02F
TA48L025F
TA48L03F
TA48L033F
TA48L05F
TA78DS05BP
TA78DS05CP
TA78DS06BP
TA78DS08BP
TA78DS09BP
TA78DS10BP
TA78DS12BP
TA78DS15BP
TA78DS05F
TA78DS05AF
TA78DS06F
TA78DS08F
TA78DS09F
TA78DS10F
TA78DS12F
TA78DS15F
TA79005S
TA79006S
TA79007S
TA79008S
TA79009S
TA79010S
TA79012S
TA79015S
TA79018S
TA79020S
TA79024S
TA79005SB
TA79006SB
TA79007SB
TA79008SB
TA79009SB
TA79010SB
TA79012SB
TA79015SB
TA79018SB
TA79020SB
TA79024SB
TA79L05F
TA79L06F
TA79L08F
TA79L09F
TA79L10F
TA79L12F
TA79L15F
TA79L18F
TA79L20F
TA79L24F
TA79L005P
TA79L006P
TA79L008P
TA79L009P
TA79L010P
TA79L012P
TA79L015P
TA79L018P
TA79L020P
TA79L024P
Use/Function
Output
Output
Current
Voltage
(typ.) (V) (max) (mA)
Input Voltage
(max) (V)
Drop-out
Voltage
(typ.) (V)
16
0.5 Max
(IO = 100 mA)
Output
Bias
Power
Voltage
Current
Dissipation
Tolerance
(typ.) (mA)
(W)
(%)
Package
Equivalent
1.8
Low-current output
Low drop-out
Surface-mount PW-MINI (SOT-89)
package
2
2.5
3
150
0.4
(IO = 0 A)
±5
(Tj = 0
to 125°C)
0.5
(Ta = 25°C)
PW-MINI
(SOT-89)
0.8
(Ta = 25°C)
TO-92MOD
0.5
(Ta = 25°C)
PW-MINI
(SOT-89)
3.3
5
5
0.6
5
Low-current output
Low drop-out
Radial tape packing for automatic
mounting
6
8
9
30
29
(load dump = 60 V)
0.3 Max
(IO = 10 mA)
0.7
10
12
0.8
15
1.0
(IO = 0 A)
BP: ±10
CP: ±5
(Ta = −40
to 85°C)
5
0.6
5
Low-current output
Low drop-out
Surface-mount PW-MINI (SOT-89)
package
6
8
9
30
29
(load dump = 60 V)
0.3 Max
(IO = 10 mA)
0.7
10
F: ±10
AF: ±5
(Ta = −40
to 85°C)
12
0.8
15
1.0
(IO = 0 A)
−5
−6
−7
4.3
−8
High-current output
Isolation package
−35
−9
−10
2.0
(IO = 1.0 A)
1000
−12
4.4
−15
−18
2.0
(Ta = 25°C)
±4
(Tj = 25°C)
20
(Tc = 25°C)
TO-220(NIS)
79XX
±4
1.8
(Tj = 25°C) (Ta = 25°C)
TPL
79XX
±4
0.5
(Tj = 25°C) (Ta = 25°C)
PW-MINI
(SOT-89)
79LXX
±4
0.8
(Tj = 25°C) (Ta = 25°C)
TO-92MOD
79LXX
4.5
−40
−20
4.6
−24
−5
−6
−7
4.3
−8
High-current output
Radial tape packing for automatic
mounting
−35
−9
−10
2.0
(IO = 1.0 A)
1000
−12
4.4
−15
−18
4.5
−40
−20
4.6
−24
−5
−6
3.1
−8
Low-current output
Surface-mount PW-MINI (SOT-89)
package
−35
−9
−10
−12
1.7
(IO = 40 mA)
150
3.2
−15
−18
3.3
−40
−20
−24
3.5
−5
−6
3.1
−8
Low-current output
Radial tape packing for automatic
mounting
−35
−9
−10
−12
1.7
(IO = 40 mA)
150
3.2
−15
−18
−20
−24
3.3
−40
3.5
139
Shunt Regulators
Polarity
Part Number
TA76431F/FR
Use/Function
Variable output voltage
Surface-mount PW-MINI (SOT-89)
package
TA76431S
Variable output voltage
Radial tape packing for automatic
mounting
TA76L431FT
Variable output voltage
Small thin surface-mount UFV package
Cathode Cathode
Reference Output
Voltage
Current
Voltage
Voltage
(typ.) (V) (typ.) (V) (max) (mA) (max) (V)
2.495
Positive-voltage output
2.49
Variable
2.495 to 36
Variable
2.49 to 19
Sink
150
37
Sink
50
20
Minimum
Cathode
Current
(max) (mA)
Reference
Voltage
Tolerance
(%)
1.0
±2.2
(Ta = 25°C)
0.5
±1.0
(Ta = 25°C)
Power Dissipation
(W)
Package
Equivalent
0.5
(Ta = 25°C)
PW-MINI
(SOT-89)
431
0.8
(Ta = 25°C)
TO-92MOD
431
0.45
(Ta = 25°C)
Mounted on
glass-epoxy substrate
UFV
431
0.8
(Ta = 25°C)
TO-92MOD
431
TA76L431S
Variable output voltage
Radial tape packing for automatic
mounting
TA76432FT
TA76432AFT
Variable output voltage
Small thin surface-mount UFV package
0.45
(Ta = 25°C)
Mounted on
glass-epoxy substrate
UFV
TA76432FC
Variable output voltage
Surface-mount SMV package
0.38
(Ta = 25°C)
Mounted on
glass-epoxy substrate
SMV
0.5
(Ta = 25°C)
PW-MINI
(SOT-89)
0.8
(Ta = 25°C)
TO-92MOD
0.38
(Ta = 25°C)
Mounted on
glass-epoxy substrate
SMV
TA76432F/FR
TA76432AF/AFR
Variable output voltage
Surface-mount PW-MINI (SOT-89)
package
TA76432S
TA76432AS
Variable output voltage
Radial tape packing for automatic
mounting
TA76433FC
Cathod separation type
Variable output voltage
Surface-mount SMV package
1.26
1.26
Variable
1.26 to 19
Variable
1.26 to 14
±1.4
Sink
20
20
Sink
20
15
0.4
0.4
A: ±1.0
(Ta = 25°C)
±1.4
(Ta = 25°C)
Multi-Functional Regulators
Positive-voltage output (low dropout)
Polarity
140
Part Number
Use/Function
TA48S018F
TA48S02F
TA48S025F
TA48S03F
TA48S033F
TA48S05F
High-current output
Low drop-out
Built-in ON/OFF control function
Bias current (OFF): 5 µA (max)
Surface-mount 5-pin PW-MOLD
package
TA8004SA
Medium-current output
Built-in power-on reset timer function
Low drop-out
Input Voltage
(max) (V)
Drop-out
Voltage
(typ.) (V)
1000
16
0.5 Max
(IO = 500 mA)
400
29
(load dump = 60 V)
0.6 Max
(IO = 400 mA)
Output
Output
Voltage
Current
(typ.) (V) (max) (mA)
Output
Bias
Power
Voltage
Current
Dissipation
Tolerance
(typ.) (mA)
(W)
(%)
Package
0.8
(IO = 0 A)
1.0
(Ta = 25°C)
10
to 125°C)
(Tc = 25°C)
PW-MOLD
5 pin
3.0
(IO = 0 A)
2.0
±5
(Ta = 25°C) TO-220N(IS)
(Ta = −40
20
5 pin
to 85°C)
(Tc = 25°C)
1.8
2
2.5
3
3.3
±4.5
(Tj = 0
5
5
Equivalent
AC-DC Converter ICs
Part Number
Package
TA1294N/F
P-SDIP24-300-1.78
P-SSOP24-300-1.78
TA1307P
P-DIP8-300-2.54A
TA1319AP/AF
P-DIP8-300-2.54A
P-SOP8-225-1.27
** TA1361P/F
TC90A75P/F
Use
Operating Supply
Voltage Range
Functions/Features
Power factor correction + PWM control, fH = 30 kHz to 110 kHz
Can be used for both flyback (external synchronization) and half-bridge converters.
7.0 to 14.0 V
Reduced standby power consumption by intermittent control, fH = 20 kHz to 150 kHz
7.5 to 11.5 V
PWM control (for power supply at 50 W or less),
AC wide input voltage, automatic frequency reduction at standby mode
9.5 to 24.0 V
P-DIP8-300-2.54A
P-SOP8-225-1.27
RCC control (for power supply at 140 W or less),
AC wide input voltage, automatic frequency reduction at standby mode
9.0 to 23.5 V
DIP8-C-300A
DIP8-F-255C
AC transformer control, reduced standby power consumption to maximum by intermittent control
AC/DC switching power
supply control
8.5 to 14.0 V
**: Under development
Other Power Supply ICs
Part Number
* TB62501F
TB62503FM
Package
Use
VQFP64
Power supply monitor + controller for notebook PCs
Power management IC for notebook PCs
Structure
SON8
Step-down power supply
Step-down DC/DC converter, 1.3-V output, efficiency = 85%
* TB62504FMG
SON8
System power supply for cellular phone PAs
Step-down DC/DC converter (variable output) + switching MOSFET,
output current capability 300 mA
TB6807F
TB6808F
VQFP64
Power supply monitor + controller for notebook PCs
Power management IC for notebook PCs
VQFP64
Power supply monitor + controller for notebook PCs
Power management IC for notebook PCs
** TB62507FMG
SON8
System power supply for cellular phone PAs
Step-down DC/DC converter (variable output) + switching MOSFET,
output current capability 500 mA
** TB62505FTG
VQON24
System power supply for cellular phone PAs
Step-down DC/DC converter (variable output) + switching MOSFET,
output current capability 500 mA + reference regulater (285 V)
*: New product
**: Under development
141
Small-Signal MMICs (High-Frequency Cell-pack)
Wide Band Amplifiers
Part Number
Package
Structure
Applications
Electrical Characteristics (Ta = 25°C)
B/W = 1.3 GHz
Gp = 15dB @f = 400 MHz, VCC = 5 V
TA4000F
SM6
Bipolar linear wideband amp
BS tuners, communications equipment,
VHF/UHF amps
TA4001F
SMQ
Bipolar linear wideband amp
BS tuners, communications equipment,
VHF/UHF amps
B/W = 2.4 GHz
Gp = 12.5dB @f = 500 MHz, VCC = 5 V
TA4002F
SMQ
Bipolar linear wideband amp
BS tuners, communications equipment,
VHF/UHF amps
B/W = 1.3 GHz
Gp = 23dB @f = 500 MHz, VCC = 5 V
TA4004F
SMV
Bipolar linear wideband amp
Communications equipment,
VHF/UHF amps
B/W = 1.2 GHz
Gp = 10.5dB @f = 500 MHz, VCC = 2 V
TA4011AFE
ESV
Bipolar linear wideband amp
Communications equipment, UHF amp
B/W = 2.4 GHz,
P01dB = −6dBmW @VCC = 2 V
TA4011FU
USV
Bipolar linear wideband amp
Communications equipment, UHF amp
B/W = 2.4 GHz,
P01dB = −6dBmW @VCC = 2 V
TA4012AFE
ESV
Bipolar linear wideband amp
Communications equipment, UHF amp
B/W = 2.0 GHz,
P01dB = 0dBmW @VCC = 2 V
TA4012FU
USV
Bipolar linear wideband amp
Communications equipment, UHF amp
B/W = 2.0 GHz,
P01dB = 0dBmW @VCC = 2 V
TA4016AFE
ES6
Bipolar linear wideband amp
Communications equipment, UHF amp
B/W = 3.2 GHz
Gp = 19dB @f = 1.5 GHz, VCC = 2 V
TA4017FT
TU6
Bipolar differential amp
CATV, IF amp
|S21|2 = 13dB, P01dB = 2dBmW @VCC = 5 V,
f = 45 MHz
TA4018F
SM8
Bipolar differential gain control amp
CATV, IF variable amp
2
|S21| = 11dB, GR = 37dB @VCC = 5 V,
f = 45 MHz
TA4019F
SM8
Bipolar differential amp
CATV, IF amp
2
|S21| = 30dB, IM3 = 53dB @VCC = 5 V,
f = 45 MHz, Pin = −35dBmW
Frequency Converters
Part Number
Package
TA4107F
SM8
TA4303F
SSOP-20
Structure
Applications
Electrical Characteristics (Ta = 25°C)
Bipolar linear down converter
CATV analog digital tuner
C・Gain = −0.5dB, IIP3 = 12dBmW @fRF = 1 GHz,
fLO = 950 MHz, VCC = 4.5 V
Bipolar linear down converter, Si-MMIC
BS tuner OSC + DBC + IF
C・Gain = 18dB/1.6 GHz,
IP3 = 17dBmW VCC = 5 V, ICC = 74 mA
High-Frequency Oscillators (VCO, TCXO)
Part Number
Package
Structure
Applications
TA4014FT
TU6
Bipolar linear OSC & buffer
TCXO
VCXO
TA4014FE
ES6
Bipolar linear OSC & buffer
TCXO
VCXO
TA4014FC
CS6
Bipolar linear OSC & buffer
TCXO
VCXO
TA4015FT
TU6
Bipolar linear OSC & buffer
TCXO
VCXO
Electrical Characteristics (Ta = 25°C)
ICC = 1.2 mA @VCC = 3.0 V
VOSC = 1.2 Vp-p (reference value)
ICC = 1.3 mA @VCC = 3.0 V
VOSC = 1.2 Vp-p (reference value)
TA4015FE
ES6
Bipolar linear OSC & buffer
TCXO
VCXO
*
TA4203F
QS16
Bipolar linear OSC & buffer & SW
GSM/DCS VCO
ICC = 40 mA @VCC = 2.7 V
PO = +10dBmW
*
TA4205FC
CS6
Bipolar linear OSC & buffer
VCO
ICC = 8 mA @VCC = 2.7 V
VOSC = 0.63 Vp-p (reference value)
*: New product
142
High-Frequency Switches
Part Number
Package
Structure
Applications
Electrical Characteristics (Ta = 25°C)
TG2210FT
TU6
GaAs low-power SPDT switch
RF general-purpose SPDT switch,
bluetooth
LOSS = 0.4dB, ISL = 30dB
Pi1dB = 18dBmW (min)
@f = 1 GHz, VC = 0 V/2.5 V
TG2211FT
TU6
GaAs low-power SPDT switch, built-in
inverter
RF general-purpose SPDT switch,
bluetooth
LOSS = 0.55dB, ISL = 17dB
Pi1dB = 22dBmW @f = 2.5 GHz, VC = 0 V/2.7 V
TG2213S
sES6
GaAs low-power SPDT switch, small type
RF general-purpose SPDT switch,
bluetooth
LOSS = 0.45dB, ISL = 22dB
Pi1dB = 17dBmW @f = 2.5 GHz, VC = 0 V/2.7 V
TG2214S
sES6
GaAs low-power SPDT switch, small type
Reverse logic type of TG2213S.
RF general-purpose SPDT switch,
bluetooth
LOSS = 0.45dB, ISL = 22dB
Pi1dB = 17dBmW @f = 2.5 GHz, VC = 0 V/2.7 V
TG2216TU
UF6
GaAs medium-power SPDT switch
Cellular phone, bluetooth, wireless LAN
LOSS = 0.7dB, ISL = 23dB
Pi1dB = 28dBmW
@f = 2.5 GHz, VC = 0 V/2.7 V
143
144