TSL202R 128 1 LINEAR SENSOR ARRAY TAOS032B – AUGUST 2002 128 × 1 Sensor-Element Organization 200 Dots-Per-Inch (DPI) Sensor Pitch High Linearity and Uniformity Wide Dynamic Range . . . 2000:1 (66 dB) Output Referenced to Ground Low Image Lag . . . 0.5% Typ Operation to 5 MHz Single 5-V Supply Replacement for TSL202 ÉÉ ÉÉ ÉÉ ÉÉ ÉÉ ÇÇ ÇÇ ÇÇ ÇÇ ÇÇ (TOP VIEW) VDD 1 SI1 2 CLK 3 AO1 4 GND 5 SO2 6 NC 7 14 NC 13 SO1 12 GND 11 NC 10 SI2 9 NC 8 AO2 NC – No internal connection Description The TSL202R linear sensor array consists of two sections of 64 photodiodes and associated charge amplifier circuitry arranged to form a contiguous 128 × 1 array. The pixels measure 120 µm (H) by 70 µm (W) with 125-µm center-to-center spacing and 55-µm spacing between pixels. Operation is simplified by internal control logic that requires only a serial-input (SI) signal and a clock. The TSL202R is intended for use in a wide variety of applications including mark detection and code reading, optical character recognition (OCR) and contact imaging, edge detection and positioning as well as optical linear and rotary encoding. Functional Block Diagram (each section — pin numbers apply to section 1) Pixel 1 Pixel 2 Integrator Reset Pixel 3 1 Pixel 64 VDD Analog Bus Output Amplifier _ 4 + AO Sample/ Output 5 GND Gain Trim Switch Control Logic Q1 CLK SI 3 Q2 RL (External 330 Load) Q3 Q64 64-Bit Shift Register 2 The LUMENOLOGY Company Copyright 2002, TAOS Inc. Texas Advanced Optoelectronic Solutions Inc. 800 Jupiter Road, Suite 205 Plano, TX 75074 (972) 673-0759 www.taosinc.com 1 TSL202R 128 1 LINEAR SENSOR ARRAY TAOS032B – AUGUST 2002 Terminal Functions TERMINAL NAME NO. DESCRIPTION AO1 4 Analog output of section 1 AO2 8 Analog output of section 2 CLK 3 Clock. Clk controls charge transfer, pixel output, and reset. GND 5,12 Ground (substrate). All voltages are referenced to GND. NC 7, 9, 11, 14 SI1 2 No internal connection Serial input (section 1). SI1 defines the start of the data-out sequence. SI2 10 Serial input (section 2). SI2 defines the start of the data-out sequence. SO1 13 Serial output (section 1). SO1 provides a signal to drive the SI2 input. SO2 6 Serial output (section 2). SO2 provides a signal to drive the SI input of another device for cascading or as an end-of-data indication. VDD 1 Supply voltage. Supply voltage for both analog and digital circuitry. Detailed Description The sensor consists of 128 photodiodes arranged in a linear array. Light energy impinging on a photodiode generates photocurrent, which is integrated by the active integration circuitry associated with that pixel. During the integration period, a sampling capacitor connects to the output of the integrator through an analog switch. The amount of charge accumulated at each pixel is directly proportional to the light intensity and the integration time. The integration time is the interval between two consecutive output periods. The output and reset of the integrators is controlled by a 128-bit shift register and reset logic. An output cycle is initiated by clocking in a logic 1 on SI for one positive going clock edge (see Figures1 and 2)†. As the SI pulse is clocked through the 128-bit shift register, the charge on the sampling capacitor of each pixel is sequentially connected to a charge-coupled output amplifier that generates a voltage output, AO. When the bit position goes low, the pixel integrator is reset. On the 129th clock rising edge, the SI pulse is clocked out of the shift register and the output assumes a high-impedance state. Note that this 129th clock pulse is required to terminate the output of the 128th pixel and return the internal logic to a known state. A subsequent SI pulse can be presented as early as the 130th clock pulse, thereby initiating another pixel output cycle. The voltage developed at analog output (AO) is given by: Vout = Vdrk + (Re) (Ee) (tint) where: Vout Vdrk Re Ee tint is is is is is the analog output voltage for white condition the analog output voltage for dark condition the device responsivity for a given wavelength of light given in V/(µJ/cm2) the incident irradiance in µW/cm2 integration time in seconds AO is driven by a source follower that requires an external pulldown resistor (330-Ω typical). The output is nominally 0 V for no light input, 2 V for normal white-level, and 3.4 V for saturation light level. When the device is not in the output phase, AO is in a high impedance state. A 0.1 µF bypass capacitor should be connected between VDD and ground as close as possible to the device. † For proper operation, after meeting the minimum hold time condition, SI must go low before the next rising edge of the clock. Copyright 2002, TAOS Inc. The LUMENOLOGY Company 2 www.taosinc.com TSL202R 128 1 LINEAR SENSOR ARRAY TAOS032B – AUGUST 2002 Absolute Maximum Ratings† Supply voltage range, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 6 V Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD + 0.3V Input clamp current, IIK (VI < 0 or VI > VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –20 mA to 20 mA Output clamp current, IOK (VO < 0 or VO > VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25 mA to 25 mA Voltage range applied to any output in the high impedance or power-off state, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD + 0.3V Continuous output current, IO (VO = 0 to VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25 mA to 25 mA Continuous current through VDD or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40 mA to 40 mA Analog output current range, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25 mA to 25 mA Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25°C to 85°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –25°C to 85°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C ESD tolerance, human body model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 V † Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Recommended Operating Conditions (see Figure 1 and Figure 2) Supply voltage, VDD MIN NOM 4.5 5 MAX UNIT 5.5 V Input voltage, VI 0 VDD V High-level input voltage, VIH Low-level input voltage, VIL 2 VDD V Wavelength of light source, λ Clock frequency, fclock Sensor integration time, serial, tint 0 0.8 400 1000 nm V 5 5000 kHz 0.026 100 ms Sensor integration time, parallel, tint Operating free-air temperature, TA 0.013 100 ms 0 70 °C Load resistance, RL 300 4700 Ω 420 pF Load capacitance, CL The LUMENOLOGY Company Copyright 2002, TAOS Inc. www.taosinc.com 3 TSL202R 128 1 LINEAR SENSOR ARRAY TAOS032B – AUGUST 2002 Electrical Characteristics at fclock = 1 MHz, VDD = 5 V, TA = 25°C, λp = 640 nm, tint = 5 ms, RL = 330 Ω, Ee = 16.5 µW/cm2 (unless otherwise noted) PARAMETER TEST CONDITIONS MIN See Note 1 TYP Vout Analog output voltage (white, average over 128 pixels) Vdrk Analog output voltage (dark, average over 128 pixels) PRNU Pixel response nonuniformity See Notes 2 & 3 Nonlinearity of analog output voltage See Note 3 ±0.4% Output noise voltage See Note 4 1 Re Responsivity SE Saturation exposure Vsat Analog output saturation voltage DSNU Dark signal nonuniformity All pixels IL Image lag See Note 7 IDD Supply current, output idle IIH High-level input current IIL Low-level input current VOH High level output voltage High-level voltage, SO1 and SO2 VOL Low level output voltage, Low-level voltage SO1 and SO2 Ci(SI) Input capacitance, SI Ci(CLK) Input capacitance, CLK MAX UNIT 1.6 2 2.4 V 0 50 150 mV ±4% ±10% 18 See Note 5 2.5 See Note 6 23 FS mVrms 30 V/ (µJ/cm 2) 142 nJ/cm 2 3.4 V 25 120 mV 8 mA VI = VDD 10 µA VI = 0 10 µA 0.5% 5 IO = 50 µA 4.5 4.95 IO = 4 mA 4.6 IO = 50 µA 0.01 IO = 4 mA 0.4 V 0.1 V 5 pF 10 pF NOTES: 1. The array is uniformly illuminated with a diffused LED source having a peak wavelength of 640 nm. 2. PRNU is the maximum difference between the voltage from any single pixel and the average output voltage from all pixels of the device under test when the array is uniformly illuminated at the white irradiance level. PRNU includes DSNU. 3. Nonlinearity is defined as the maximum deviation from a best-fit straight line over the dark-to-white irradiance levels, as a percent of analog output voltage (white). 4. RMS noise is the standard deviation of a single-pixel output under constant illumination as observed over a 5-second period. 5. Minimum saturation exposure is calculated using the minimum Vsat, the maximum Vdrk, and the maximum Re. 6. DSNU is the difference between the maximum and minimum output voltage in the absence of illumination. 7. Image lag is a residual signal left in a pixel from a previous exposure. It is defined as a percent of white-level signal remaining after a pixel is exposed to a white condition followed by a dark condition: IL V out (IL) V drk 100 V out (white) V drk Timing Requirements (see Figure 1 and Figure 2) MIN tsu(SI) Setup time, serial input (see Note 8) th(SI) Hold time, serial input (see Note 8 and Note 9) tw Pulse duration, clock high or low 50 tr, tf Input transition (rise and fall) time 0 NOM MAX UNIT 20 ns 0 ns ns 500 ns NOTES: 8. Input pulses have the following characteristics: tr = 6 ns, tf = 6 ns. 9. SI must go low before the rising edge of the next clock pulse. Copyright 2002, TAOS Inc. The LUMENOLOGY Company 4 www.taosinc.com TSL202R 128 1 LINEAR SENSOR ARRAY TAOS032B – AUGUST 2002 Dynamic Characteristics over recommended ranges of supply voltage and operating free-air temperature (see Figure 2) PARAMETER ts Analog output settling time to ±1% tpd(SO) Propagation delay time, SO1, SO2 TEST CONDITIONS RL = 330 Ω, MIN CL = 10 pF TYP MAX UNIT 185 ns 50 ns TYPICAL CHARACTERISTICS CLK SI ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎ 129 Clock Cycles AO Hi-Z Hi-Z Figure 1. Timing Waveforms tw 1 (65) 2 (66) 64 (128) 65 (129) 5V CLK 2.5 V 2.5 V 2.5 V 0V tsu(SI) 5V SI1 (SI2) 2.5 V 2.5 V 0V th(SI) tpd(SO) tpd(SO) SO1 (SO2) ts ts AO1 (A02) Pixel 1 (65) Pixel 64 (128) Figure 2. Operational Waveforms (each section) The LUMENOLOGY Company Copyright 2002, TAOS Inc. www.taosinc.com 5 TSL202R 128 1 LINEAR SENSOR ARRAY TAOS032B – AUGUST 2002 TYPICAL CHARACTERISTICS ANALOG OUTPUT SETTLING TIME vs LOAD CAPACITANCE AND RESISTANCE PHOTODIODE SPECTRAL RESPONSIVITY 1 600 TA = 25°C 500 ts — Settling Time to 1% — ns Normalized Responsivity 0.8 0.6 0.4 0.2 0 300 470 pF VDD = 5 V Vout = 1 V 220 pF 400 100 pF 300 10 pF 200 100 0 400 500 600 700 800 900 1000 1100 λ – Wavelength – nm 0 200 400 1000 1200 The LUMENOLOGY Company 6 800 Figure 4 Figure 3 Copyright 2002, TAOS Inc. 600 RL – Load Resistance – Ω www.taosinc.com TSL202R 128 1 LINEAR SENSOR ARRAY TAOS032B – AUGUST 2002 APPLICATION INFORMATION Power Supply Considerations For optimum device performance, power-supply lines should be decoupled by a 0.01-µF to 0.1-µF capacitor with short leads mounted close to the device package (see Figure 5 and Figure 6). Connection Diagrams VDD 0.1 µF TSL202R 1 2 3 4 5 6 7 SI CLK VDD SI1 CLK AO1 GND SO2 VDD NC SO1 GND NC SI2 NC AO2 14 13 12 11 10 9 8 AO RL Figure 5. Serial Connection VDD TSL202R 0.1 µF 1 2 3 4 5 6 7 Si CLK AO1 (Pixels 1–64) RL VDD SI1 CLK AO1 GND SO2 VDD NC SO1 GND NC SI2 NC AO2 14 13 12 11 10 9 8 AO2 (Pixels 65–128) RL Figure 6. Parallel Connection The LUMENOLOGY Company Copyright 2002, TAOS Inc. www.taosinc.com 7 TSL202R 128 1 LINEAR SENSOR ARRAY TAOS032B – AUGUST 2002 MECHANICAL INFORMATION This assembly consists of 2 sensor chips mounted on a printed-circuit board in a clear molded plastic package. TOP VIEW 19.30 18.29 Sensors CL Sensors 3.62 to Pin 1 3.92 ÉÉÉÉÉÉÇÇÇÇÇ Pixel 1 0.53 to Pin 1 0.28 10.67 9.65 Pin 1 Indicator END VIEW SIDE VIEW 3.18 2.79 Top of Die to 0.89 Top of Package 1.29 ÏÏÏÏÏÏÏÏÏÏÏ ÏÏÏÏÏÏÏÏÏÏÏ 14 4.60 MIN ÏÏÏÏÏÏ ÏÏÏÏÏÏ 14 14 0.50 0.00 0.508 0.406 BOTTOM VIEW 1.90 0.76 1 2 3 4 5 6 7 14 13 12 11 10 9 8 7.87 7.37 2 2.16 1.42 ÌÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ ÌÌÌÌÌ 12 2.54 Nonaccumulative See Note B NOTES: A. All linear dimensions are in millimeters. B. The true-position spacing is 2.54 mm between lead centerlines. Each pin centerline is located within 0.25 mm of its true longitudinal positions. C. Index of refraction of clear plastic is 1.52. D. This drawing is subject to change without notice. Figure 7. Packaging Configuration Copyright 2002, TAOS Inc. The LUMENOLOGY Company 8 www.taosinc.com TSL202R 128 1 LINEAR SENSOR ARRAY TAOS032B – AUGUST 2002 PRODUCTION DATA — information in this document is current at publication date. Products conform to specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard warranty. Production processing does not necessarily include testing of all parameters. NOTICE Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reserves the right to make changes to the products contained in this document to improve performance or for any other purpose, or to discontinue them without notice. Customers are advised to contact TAOS to obtain the latest product information before placing orders or designing TAOS products into systems. TAOS assumes no responsibility for the use of any products or circuits described in this document or customer product design, conveys no license, either expressed or implied, under any patent or other right, and makes no representation that the circuits are free of patent infringement. TAOS further makes no claim as to the suitability of its products for any particular purpose, nor does TAOS assume any liability arising out of the use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY RESULT IN PERSONAL INJURY OR DEATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY UNAUTHORIZED AND ANY SUCH USE BY A CUSTOMER IS COMPLETELY AT THE CUSTOMER’S RISK. LUMENOLOGY is a registered trademark, and TAOS, the TAOS logo, and Texas Advanced Optoelectronic Solutions are trademarks of Texas Advanced Optoelectronic Solutions Incorporated. The LUMENOLOGY Company Copyright 2002, TAOS Inc. www.taosinc.com 9