TSL1401CL

TAOS Inc.
is now
ams AG
The technical content of this TAOS datasheet is still valid.
Contact information:
Headquarters:
ams AG
Tobelbaderstrasse 30
8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0
e-Mail: [email protected]
Please visit our website at www.ams.com
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
r
r
128 × 1 Sensor-Element Organization
400 Dots-Per-Inch (DPI) Sensor Pitch
High Linearity and Uniformity
Wide Dynamic Range . . . 4000:1 (72 dB)
Output Referenced to Ground
Low Image Lag . . . 0.5% Typ
Operation to 8 MHz
Single 3-V to 5-V Supply
Rail-to-Rail Output Swing (AO)
No External Load Resistor Required
Replacement for TSL1401R−LF
RoHS Compliant
SI 1
8 NC
CLK 2
7 GND
AO 3
6 GND
VDD 4
5 NC
NC − No internal connection
lv
Package Drawing is Not to Scale
am
lc s
on A
te G
nt
st
il
Description
CL PACKAGE
(TOP VIEW)
al
id
D
D
D
D
D
D
D
D
D
D
D
D
TAOS136 − JULY 2011
The TSL1401CL linear sensor array consists of a 128 × 1 array of photodiodes, associated charge amplifier
circuitry, and an internal pixel data-hold function that provides simultaneous-integration start and stop times for
all pixels. The array is made up of 128 pixels, each of which has a photo-sensitive area of 3,524.3 square
micrometers. There is 8-μm spacing between pixels. Operation is simplified by internal control logic that requires
only a serial-input (SI) signal and a clock.
Functional Block Diagram
Pixel 1
S1
_
Pixel
3
Pixel
128
2
1
Output
Buffer
3
ch
ni
S2
Sample/Hold/
Output
CLK
SI
2
VDD
3
AO
6, 7
GND
Switch Control Logic
Q1
Te
Hold
4
Analog
Bus
ca
+
Pixel
2
1 Integrator
Reset
2
Q2
Q3
Q128
Gain
Trim
128-Bit Shift Register
1
The LUMENOLOGY r Company
Copyright E 2011, TAOS Inc.
r
Texas Advanced Optoelectronic Solutions Inc.
1001 Klein Road S Suite 300 S Plano, TX 75074 S (972)
r 673-0759
www.taosinc.com
1
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
Terminal Functions
TERMINAL
NO.
AO
3
Analog output.
CLK
2
Clock. The clock controls charge transfer, pixel output, and reset.
GND
6, 7
Ground (substrate). All voltages are referenced to the substrate.
NC
5, 8
No internal connection.
SI
1
Serial input. SI defines the start of the data-out sequence.
VDD
4
Supply voltage. Supply voltage for both analog and digital circuits.
Detailed Description
al
id
DESCRIPTION
NAME
lv
The sensor consists of 128 photodiodes arranged in a linear array. Light energy impinging on a photodiode
generates photocurrent, which is integrated by the active integration circuitry associated with that pixel.
am
lc s
on A
te G
nt
st
il
During the integration period, a sampling capacitor connects to the output of the integrator through an analog
switch. The amount of charge accumulated at each pixel is directly proportional to the light intensity and the
integration time.
The output and reset of the integrators is controlled by a 128-bit shift register and reset logic. An output cycle
is initiated by clocking in a logic 1 on SI. For proper operation, after meeting the minimum hold time condition,
SI must go low before the next rising edge of the clock. An internal signal, called Hold, is generated from the
rising edge of SI and transmitted to analog switches in the pixel circuit. This causes all 128 sampling capacitors
to be disconnected from their respective integrators and starts an integrator reset period. As the SI pulse is
clocked through the shift register, the charge stored on the sampling capacitors is sequentially connected to a
charge-coupled output amplifier that generates a voltage on analog output AO. Simultaneously, during the first
18 clock cycles, all pixel integrators are reset, and the next integration cycle begins on the 19th clock. On the
129th clock rising edge, the SI pulse is clocked out of the shift register and the analog output AO assumes a
high impedance state. Note that this 129th clock pulse is required to terminate the output of the 128th pixel, and
return the internal logic to a known state. If a minimum integration time is desired, the next SI pulse may be
presented after a minimum delay of tqt (pixel charge transfer time) after the 129th clock pulse.
AO is an op amp-type output that does not require an external pull-down resistor. This design allows a rail-to-rail
output voltage swing. With VDD = 5 V, the output is nominally 0 V for no light input, 2 V for normal white level, and 4.8 V
for saturation light level. When the device is not in the output phase, AO is in a high-impedance state.
ca
The voltage developed at analog output (AO) is given by:
Vout = Vdrk + (Re) (Ee)(tint)
ni
is the analog output voltage for white condition
is the analog output voltage for dark condition
is the device responsivity for a given wavelength of light given in V/(μJ/cm2)
is the incident irradiance in μW/cm2
is integration time in seconds
ch
where:
Vout
Vdrk
Re
Ee
tint
Te
A 0.1 μF bypass capacitor should be connected between VDD and ground as close as possible to the device.
The TSL1401CL is intended for use in a wide variety of applications, including: image scanning, mark and code
reading, optical character recognition (OCR) and contact imaging, edge detection and positioning, and optical
linear and rotary encoding.
Copyright E 2011, TAOS Inc.
The LUMENOLOGY r Company
r
r
2
www.taosinc.com
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
Absolute Maximum Ratings†
lv
al
id
Supply voltage range, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6 V
Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VDD + 0.3V
Input clamp current, IIK (VI < 0) or (VI > VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −20 mA to 20 mA
Output clamp current, IOK (VO < 0 or VO > VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25 mA to 25 mA
Voltage range applied to any output in the high impedance or power-off state, VO . . . −0.3 V to VDD + 0.3 V
Continuous output current, IO (VO = 0 to VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25 mA to 25 mA
Continuous current through VDD or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40 mA to 40 mA
Analog output current range, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25 mA to 25 mA
Maximum light exposure at 638 nm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 mJ/cm2
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25°C to 85°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25°C to 85°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds‡ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
ESD tolerance, human body model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 V
†
am
lc s
on A
te G
nt
st
il
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “Recommended Operating Conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡ Not recommended for solder reflow.
Recommended Operating Conditions (see Figure 1 and Figure 2)
Supply voltage, VDD
MIN
NOM
MAX
3
5
5.5
UNIT
V
Input voltage, VI
High-level input voltage, VIH
0
VDD
V
2
VDD
V
Low-level input voltage, VIL
Wavelength of light source, λ
0
0.8
V
400
1000
Clock frequency, fclock
5
Sensor integration time, tint (see Note 1)
Setup time, serial input, tsu(SI)
0.03375
nm
8000
kHz
100
ms
20
ns
Hold time, serial input, th(SI) (see Note 2)
0
ns
Operating free-air temperature, TA
0
70
°C
Te
ch
ni
ca
NOTES: 1. Integration time is calculated as follows:
tint(min) = (128 − 18) clock period + 20 ms
where 128 is the number of pixels in series, 18 is the required logic setup clocks, and 20 ms is the pixel charge transfer time (tqt)
2. SI must go low before the rising edge of the next clock pulse.
The LUMENOLOGY r Company
Copyright E 2011, TAOS Inc.
r
r
www.taosinc.com
3
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
Electrical Characteristics at fclock = 1 MHz, VDD = 5 V, TA = 25°C, λp = 640 nm, tint = 5 ms,
RL = 330 Ω, Ee = 11 μW/cm2 (unless otherwise noted) (see Note 3)
TEST CONDITIONS
MIN
TYP
MAX
1.6
2
2.4
V
0.1
0.2
V
± 4%
± 10%
Analog output voltage (white, average over 128 pixels)
See Note 4
Vdrk
Analog output voltage (dark, average over 128 pixels)
Ee = 0
PRNU
Pixel response nonuniformity
See Note 5
Nonlinearity of analog output voltage
See Note 6
± 0.4%
Output noise voltage
See Note 7
1
Re
Responsivity
See Note 8
25
35
4.8
Analog output saturation voltage
VDD = 5 V, RL = 330 Ω
4.5
Vsat
VDD = 3 V, RL = 330 Ω
2.5
2.8
SE
Saturation exposure
DSNU
Dark signal nonuniformity
All pixels, Ee = 0, See Note 10
IL
Image lag
See Note 11
IDD
Supply current
IIH
High-level input current
IIL
Low-level input current
Ci
Input capacitance
0
136
FS
mVrms
45
V/
(μJ/cm 2)
V
nJ/cm 2
lv
VDD = 5 V, See Note 9
UNIT
al
id
PARAMETER
Vout
VDD = 3 V, See Note 9
78
0.02
0.05
V
am
lc s
on A
te G
nt
st
il
0.5%
VDD = 5 V, Ee = 0
2.8
4.5
VDD = 3 V, Ee = 0
2.6
4.5
VI = VDD
VI = 0
mA
1
μA
1
μA
5
pF
ca
NOTES: 3. All measurements made with a 0.1 μF capacitor connected between VDD and ground.
4. The array is uniformly illuminated with a diffused LED source having a peak wavelength of 640 nm.
5. PRNU is the maximum difference between the voltage from any single pixel and the average output voltage from all pixels of the
device under test when the array is uniformly illuminated at the white irradiance level. PRNU includes DSNU.
6. Nonlinearity is defined as the maximum deviation from a best-fit straight line over the dark-to-white irradiance levels, as a percent
of analog output voltage (white).
7. RMS noise is the standard deviation of a single-pixel output under constant illumination as observed over a 5-second period.
8. Re(min) = [Vout(min) − Vdrk(max)] ÷ (Ee × tint)
9. SE(min) = [Vsat(min) − Vdrk(min)] × 〈Ee × tint) ÷ [Vout(max) − Vdrk(min)]
10. DSNU is the difference between the maximum and minimum output voltage for all pixels in the absence of illumination.
11. Image lag is a residual signal left in a pixel from a previous exposure. It is defined as a percent of white-level signal remaining after
a pixel is exposed to a white condition followed by a dark condition:
V out (IL) * V drk
IL +
100
V out (white) * V drk
Timing Requirements (see Figure 1 and Figure 2)
MIN
Setup time, serial input (see Note 12)
th(SI)
Hold time, serial input (see Note 12 and Note 13)
tw
Pulse duration, clock high or low
50
tr, tf
Input transition (rise and fall) time
0
ch
tqt
ni
tsu(SI)
Pixel charge transfer time
NOM
MAX
UNIT
20
ns
0
ns
ns
500
ns
μs
20
Te
NOTES: 12. Input pulses have the following characteristics: tr = 6 ns, tf = 6 ns.
13. SI must go low before the rising edge of the next clock pulse.
Dynamic Characteristics over recommended ranges of supply voltage and operating free-air
temperature (see Figures 7 and 8)
ts
PARAMETER
TEST CONDITIONS
Analog output settling time to ± 1%
Copyright E 2011, TAOS Inc.
RL = 330 Ω,
CL = 10 pF
TYP
120
MAX
UNIT
ns
The LUMENOLOGY r Company
r
r
4
MIN
www.taosinc.com
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
PARAMETER MEASUREMENT INFORMATION
CLK
al
id
tqt
SI
Internal
Reset
tint
Not Integrating
Integrating
lv
Integration
18 Clock Cycles
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
AO
Hi-Z
am
lc s
on A
te G
nt
st
il
129 Clock Cycles
Hi-Z
Figure 1. Timing Waveforms
tw
1
2
128
129
5V
2.5 V
CLK
tsu(SI)
50%
SI
th(SI)
0V
5V
0V
ts
AO
Pixel 128
ca
Pixel 1
Te
ch
ni
Figure 2. Operational Waveforms
The LUMENOLOGY r Company
Copyright E 2011, TAOS Inc.
r
r
www.taosinc.com
5
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
TYPICAL CHARACTERISTICS
NORMALIZED IDLE SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
PHOTODIODE SPECTRAL RESPONSIVITY
1
2
0.4
0.2
0
300
al
id
0.6
1.5
1
0.5
am
lc s
on A
te G
nt
st
il
Relative Responsivity
0.8
lv
IDD — Normalized Idle Supply Current
TA = 25°C
0
400
500
600
700
800
900
1000 1100
0
10
20
Figure 3
70
0.10
tint = 0.5 ms
tint = 1 ms
VDD = 5 V
ca
Vout — Output Voltage
0.09
1.5
ni
1
0.5
10
Copyright E 2011, TAOS Inc.
tint = 15 ms
tint = 5 ms
tint = 2.5 ms
0.06
20
30
40
60
50
TA − Free-Air Temperature − °C
Te
0
0.08
0.07
ch
Vout — Output Voltage — V
60
DARK OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
VDD = 5 V
tint = 0.5 ms to 15 ms
70
0
10
20
30
40
60
50
TA − Free-Air Temperature − °C
70
Figure 6
Figure 5
The LUMENOLOGY r Company
r
r
6
50
Figure 4
WHITE OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
0
40
TA − Free-Air Temperature − °C
λ − Wavelength − nm
2
30
www.taosinc.com
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
TYPICAL CHARACTERISTICS
SETTLING TIME
vs.
LOAD
SETTLING TIME
vs.
LOAD
600
600
VDD = 3 V
Vout = 1 V
VDD = 5 V
Vout = 1 V
220 pF
300
200
100 pF
470 pF
400
220 pF
300
lv
Settling Time to 1% — ns
400
al
id
500
470 pF
200
100 pF
am
lc s
on A
te G
nt
st
il
Settling Time to 1% — ns
500
100
100
10 pF
0
0
200
400
600
800
RL — Load Resistance − W
1000
0
0
10 pF
200
400
600
800
RL — Load Resistance − W
Figure 8
Te
ch
ni
ca
Figure 7
1000
The LUMENOLOGY r Company
Copyright E 2011, TAOS Inc.
r
r
www.taosinc.com
7
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
PRINCIPLES OF OPERATION
Integration Time
al
id
The integration time of the linear array is the period during which light is sampled and charge accumulates on
each pixel’s integrating capacitor. The flexibility to adjust the integration period is a powerful and useful feature
of the TAOS TSL14xx linear array family. By changing the integration time, a desired output voltage can be
obtained on the output pin while avoiding saturation for a wide range of light levels.
lv
The integration time is the time between the SI (Start Integration) positive pulse and the HOLD positive pulse
minus the 18 setup clocks. The TSL14xx linear array is normally configured with the SI and HOLD pins tied
together. This configuration will be assumed unless otherwise noted. Sending a high pulse to SI (observing
timing rules for setup and hold to clock edge) starts a new cycle of pixel output and integration setup. However,
a minimum of (n+1) clocks, where n is the number of pixels, must occur before the next high pulse is applied
to SI. It is not necessary to send SI immediately on/after the (n+1) clocks. A wait time adding up to a maximum
total of 100 ms between SI pulses can be added to increase the integration time creating a higher output voltage
in low light applications.
am
lc s
on A
te G
nt
st
il
Each pixel of the linear array consists of a light-sensitive photodiode. The photodiode converts light intensity
to a voltage. The voltage is sampled on the Sampling Capacitor by closing switch S2 (position 1) (see the
Functional Block Diagram on page 1). Logic controls the resetting of the Integrating Capacitor to zero by closing
switch S1 (position 2).
At SI input, all of the pixel voltages are simultaneously scanned and held by moving S2 to position 2 for all pixels.
During this event, S2 for pixel 1 is in position 3. This makes the voltage of pixel 1 available on the analog output.
On the next clock, S2 for pixel 1 is put into position 2 and S2 for pixel 2 is put into position 3 so that the voltage
of pixel 2 is available on the output.
Following the SI pulse and the next 17 clocks after the SI pulse is applied, the S1 switch for all pixels remains
in position 2 to reset (zero out) the integrating capacitor so that it is ready to begin the next integration cycle.
On the rising edge of the 19th clock, the S1 switch for all the pixels is put into position 1 and all of the pixels begin
a new integration cycle.
The first 18 pixel voltages are output during the time the integrating capacitor is being reset. On the 19th clock
following an SI pulse, pixels 1 through 18 have switch S2 in position 1 so that the sampling capacitor can begin
storing charge. For the period from the 19th clock through the nth clock, S2 is put into position 3 to read the output
voltage during the nth clock. On the next clock the previous pixel S2 switch is put into position 1 to start sampling
the integrating capacitor voltage. For example, S2 for pixel 19 moves to position 1 on the 20th clock. On the n+1
clock, the S2 switch for the last (nth) pixel is put into position 1 and the output goes to a high-impedance state.
ni
ca
If a SI was initiated on the n+1 clock, there would be no time for the sampling capacitor of pixel n to charge to
the voltage level of the integrating capacitor. The minimum time needed to guarantee the sampling capacitor
for pixel n will charge to the voltage level of the integrating capacitor is the charge transfer time of 20 μs.
Therefore, after n+1 clocks, an extra 20 μs wait must occur before the next SI pulse to start a new integration
and output cycle.
Te
ch
The minimum integration time for any given array is determined by time required to clock out all the pixels
in the array and the time to discharge the pixels. The time required to discharge the pixels is a constant.
Therefore, the minimum integration period is simply a function of the clock frequency and the number of pixels
in the array. A slower clock speed increases the minimum integration time and reduces the maximum light level
for saturation on the output. The minimum integration time shown in this data sheet is based on the maximum
clock frequency of 8 MHz.
Copyright E 2011, TAOS Inc.
The LUMENOLOGY r Company
r
r
8
www.taosinc.com
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
APPLICATION INFORMATION
The minimum integration time can be calculated from the equation:
T int(min) +
1
ǒmaximum clock
Ǔ
frequency
(n * 18)pixels ) 20ms
where:
is the number of pixels
al
id
n
In the case of the TSL1401CL with the maximum clock frequency of 8 MHz, the minimum integration time would
be:
(128 * 18) ) 20 ms + 33.75 ms
lv
T int(min) + 0.125 ms
am
lc s
on A
te G
nt
st
il
It is good practice on initial power up to run the clock (n+1) times after the first SI pulse to clock out indeterminate
data from power up. After that, the SI pulse is valid from the time following (n+1) clocks. The output will go into
a high-impedance state after the n+1 high clock edge. It is good practice to leave the clock in a low state when
inactive because the SI pulse required to start a new cycle is a low-to-high transition.
The integration time chosen is valid as long as it falls in the range between the minimum and maximum limits
for integration time. If the amount of light incident on the array during a given integration period produces a
saturated output (Max Voltage output), then the data is not accurate. If this occurs, the integration period should
be reduced until the analog output voltage for each pixel falls below the saturation level. The goal of reducing
the period of time the light sampling window is active is to lower the output voltage level to prevent saturation.
However, the integration time must still be greater than or equal to the minimum integration period.
If the light intensity produces an output below desired signal levels, the output voltage level can be increased
by increasing the integration period provided that the maximum integration time is not exceeded. The maximum
integration time is limited by the length of time the integrating capacitors on the pixels can hold their accumulated
charge. The maximum integration time should not exceed 100 ms for accurate measurements.
It should be noted that the data from the light sampled during one integration period is made available on the
analog output during the next integration period and is clocked out sequentially at a rate of one pixel per clock
period. In other words, at any given time, two groups of data are being handled by the linear array: the previous
measured light data is clocked out as the next light sample is being integrated.
Te
ch
ni
ca
Although the linear array is capable of running over a wide range of operating frequencies up to a maximum
of 8 MHz, the speed of the A/D converter used in the application is likely to be the limiter for the maximum clock
frequency. The voltage output is available for the whole period of the clock, so the setup and hold times required
for the analog-to-digital conversion must be less than the clock period.
The LUMENOLOGY r Company
Copyright E 2011, TAOS Inc.
r
r
www.taosinc.com
9
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
APPLICATION INFORMATION: HARDWARE
PCB Pad Layout
Suggested PCB pad layout guidelines for the CL package are shown in Figure 9.
1.3
al
id
Pin 1
lv
1.4
am
lc s
on A
te G
nt
st
il
2.5
0.8
0.8
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
Te
ch
ni
ca
Figure 9. Suggested CL Package PCB Layout
Copyright E 2011, TAOS Inc.
The LUMENOLOGY r Company
r
r
10
www.taosinc.com
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
PACKAGE INFORMATION
TOP VIEW
ARRAY DETAIL A
(Note B)
8
3.0 0.2
A
63.5
al
id
0.0635
(Note B)
76.6
95.3
Pin 1
55.5
46
9.4 0.2
Photodiode Array
(Not to Scale)
am
lc s
on A
te G
nt
st
il
SIDE VIEW
lv
8.064 (see note B)
37
END VIEW
0.22
BOTTOM
VIEW
CL of Solder Contact
CL of Pixel 5
1.2 0.2
Photodiode Array
(Not to Scale)
0.0208
Pin 1
0.95
0.8
0.95
0.305
0.6
CL of Package
ca
1.8
CL of Photodiode Array Area
2.5
1.0
Pb
ni
0.6
7.5 0.08
Te
ch
NOTES: A. All linear dimensions are in millimeters. Dimension tolerance is ± 0.05 mm unless otherwise noted.
B. Nominal photodiode array dimension. The array is made up of 124 inner pixels, 2 next-to-end pixels, and 2 end pixels. Pixel
#1 is closer to Pin 1. The inner pixels measure 63.5 μm (H) by 55.5 μm (W), the next-to-end pixels are 76.6 μm (H) by
46 μm (W), and the end pixels are 95.3 μm (H) by 37 μm (W). There is 8-μm spacing between all pixels. See Array Detail A.
C. Package top surface is molded with an electrically nonconductive clear plastic compound having an index of refraction of 1.56.
D. Contact finish is soft gold plated.
E. This package contains no lead (Pb).
F. This drawing is subject to change without notice.
The LUMENOLOGY r Company
Figure 10. Package CL Configuration
Copyright E 2011, TAOS Inc.
r
r
www.taosinc.com
11
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
CARRIER TAPE AND REEL INFORMATION
TOP VIEW
2.00
4.00
8.00
1.50
+ 0.10
− 0.00
1.75
al
id
B
16.00
+ 0.30
− 0.10
1.50
+ 0.25
− 0.00
8 Max
7 Max
9.85
1.53
Bo
Ko
ch
ni
ca
Ao
B
DETAIL B
0.30
0.02
3.45
A
am
lc s
on A
te G
nt
st
il
DETAIL A
A
lv
7.50
All linear dimensions are in millimeters. Dimension tolerance is ± 0.10 mm unless otherwise noted.
The dimensions on this drawing are for illustrative purposes only. Dimensions of an actual carrier may vary slightly.
Symbols on drawing Ao, Bo, and Ko are defined in ANSI EIA Standard 481−B 2001.
Each reel is 178 millimeters in diameter and contains 1000 parts.
TAOS packaging tape and reel conform to the requirements of EIA Standard 481−B.
In accordance with EIA standard, device pin 1 is located next to the sprocket holes in the tape.
This drawing is subject to change without notice.
Te
NOTES: A.
B.
C.
D.
E.
F.
G.
Copyright E 2011, TAOS Inc.
Figure 11. Package CL Carrier Tape
The LUMENOLOGY r Company
r
r
12
www.taosinc.com
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
SOLDERING INFORMATION
The CL package has been tested and has demonstrated an ability to be reflow soldered to a PCB substrate.
Table 1. Solder Reflow Profile
PARAMETER
REFERENCE
DEVICE
Average temperature gradient in preheating
tsoak
2 to 3 minutes
Time above 217°C (T1)
t1
Max 60 sec
Time above 230°C (T2)
t2
Max 50 sec
Time above Tpeak −10°C (T3)
t3
Max 10 sec
Tpeak
260°C
am
lc s
on A
te G
nt
st
il
Peak temperature in reflow
lv
Soak time
2.5°C/sec
Temperature gradient in cooling
Max −5°C/sec
Not to scale — for reference only
T3
T2
t3
t2
tsoak
t1
Figure 12. Solder Reflow Profile Graph
Te
ch
Time (sec)
ni
Temperature (C)
T1
ca
Tpeak
al
id
The solder reflow profile describes the expected maximum heat exposure of components during the solder
reflow process of product on a PCB. Temperature is measured on top of component. The components should
be limited to a maximum of three passes through this solder reflow profile.
The LUMENOLOGY r Company
Copyright E 2011, TAOS Inc.
r
r
www.taosinc.com
13
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
STORAGE INFORMATION
Moisture Sensitivity
al
id
Optical characteristics of the device can be adversely affected during the soldering process by the release and
vaporization of moisture that has been previously absorbed into the package. To ensure the package contains
the smallest amount of absorbed moisture possible, each device is dry-baked prior to being packed for shipping.
Devices are packed in a sealed aluminized envelope called a moisture barrier bag with silica gel to protect them
from ambient moisture during shipping, handling, and storage before use.
The CL package has been assigned a moisture sensitivity level of MSL 5a and the devices should be stored
under the following conditions:
5°C to 50°C
60% maximum
6 months from the date code on the aluminized envelope — if unopened
24 hours or fewer
lv
Temperature Range
Relative Humidity
Total Time
Opened Time
Te
ch
ni
ca
am
lc s
on A
te G
nt
st
il
Rebaking will be required if the devices have been stored unopened for more than 6 months or if the aluminized
envelope has been open for more than 24 hours. If rebaking is required, it should be done at 60°C for 24 hours.
Copyright E 2011, TAOS Inc.
The LUMENOLOGY r Company
r
r
14
www.taosinc.com
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
TAOS136 − JULY 2011
PRODUCTION DATA — information in this document is current at publication date. Products conform to
specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard
warranty. Production processing does not necessarily include testing of all parameters.
LEAD-FREE (Pb-FREE) and GREEN STATEMENT
al
id
Pb-Free (RoHS) TAOS’ terms Lead-Free or Pb-Free mean semiconductor products that are compatible with the current
RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous
materials. Where designed to be soldered at high temperatures, TAOS Pb-Free products are suitable for use in specified
lead-free processes.
Green (RoHS & no Sb/Br) TAOS defines Green to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and
Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material).
am
lc s
on A
te G
nt
st
il
lv
Important Information and Disclaimer The information provided in this statement represents TAOS’ knowledge and
belief as of the date that it is provided. TAOS bases its knowledge and belief on information provided by third parties,
and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate
information from third parties. TAOS has taken and continues to take reasonable steps to provide representative
and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and
chemicals. TAOS and TAOS suppliers consider certain information to be proprietary, and thus CAS numbers and other
limited information may not be available for release.
NOTICE
Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reserves the right to make changes to the products contained in this
document to improve performance or for any other purpose, or to discontinue them without notice. Customers are advised
to contact TAOS to obtain the latest product information before placing orders or designing TAOS products into systems.
TAOS assumes no responsibility for the use of any products or circuits described in this document or customer product
design, conveys no license, either expressed or implied, under any patent or other right, and makes no representation that
the circuits are free of patent infringement. TAOS further makes no claim as to the suitability of its products for any particular
purpose, nor does TAOS assume any liability arising out of the use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages.
ca
TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR
USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY
RESULT IN PERSONAL INJURY OR DEATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY
UNAUTHORIZED AND ANY SUCH USE BY A CUSTOMER IS COMPLETELY AT THE CUSTOMER’S RISK.
Te
ch
ni
LUMENOLOGY, TAOS, the TAOS logo, and Texas Advanced Optoelectronic Solutions are registered trademarks of Texas Advanced
Optoelectronic Solutions Incorporated.
The LUMENOLOGY r Company
Copyright E 2011, TAOS Inc.
r
r
www.taosinc.com
15
TSL1401CL
128 × 1 LINEAR SENSOR ARRAY WITH HOLD
Te
ch
ni
ca
am
lc s
on A
te G
nt
st
il
lv
al
id
TAOS136 − JULY 2011
Copyright E 2011, TAOS Inc.
The LUMENOLOGY r Company
r
r
16
www.taosinc.com