Integrated Circuit Systems, Inc. ICS9169C-232 Frequency Generator for Pentium™ Based Systems General Description Features The ICS9169C-232 is a low-cost frequency generator designed specifically for Pentium and Pentium-Pro based chip set systems. The integrated buffer minimizes skew and provides all the clocks required. A 14.318 MHz XTAL oscillator provides the reference clock to generate standard Pentium frequencies. The CPU clock makes gradual frequency transitions without violating the PLL timing of internal microprocessor clock multipliers. A raised frequency setting of 68.5 MHz is available for Turbo-mode of the 66.8 MHz CPU. The ICS9169C-232 contains 8 CPU clocks, 6 PCI clocks, 1 REF at 48MHz and 1 at 24MHz. • • • Strong output drive. Eight selectable CPU clocks operate up to 83.3 MHz Frequency selections include Turbo-mode speed of 68.5 MHz Maximum CPU jitter of ±200ps Six BUS clocks support sync or async bus operation 250ps skew window for CPU outputs, 500ps skew window for BUS outputs CPU clocks to BUS clocks skew 1-4 ns (CPU early) 48 MHz clock for USB support & 24 MHz clock for FD. Logic inputs latched at Power-On for frequency selection saving pins as Input/Output Integrated buffer outputs drive up to 30pF loads 3.0V - 3.7V supply range, CPU (1:6) outputs 2.5V (2.375 - 2.6V) VDD option 28-pin SOIC or SSOP package • • • • • • Either synchronous (CPU/2) or asynchronous (32 MHz) PCI bus operation can be selected by latching data on BSEL input. • • • Block Diagram Pin Configuration 28-Pin SOIC or SSOP Functionality 3.3V±10%, 0-70°C Crystal (X1, X2) = 14.31818 MHz ADD RESS SEL ECT FS2 FS1 VDD Groups: VDD1 = X1, X2, REF/BSEL VDD2 = CPU1-6 VDD3 = CPU7-8 & PLL Core VDD4 = BUS1-6 VDD5 = 48/24 MHz Latched Inputs: L1 = BSEL L2 = FS0 L3 = FS1 L4 = FS2 CP U(1:8) (MHz) FS0 BU S (1:6)MHz 48MHz 24MHz RE F BSEL=1 BSEL=0 0 0 0 50 25 32 48 24 REF 0 0 1 60 30 32 48 24 REF 0 1 0 66.8 33.4 32 48 24 REF 0 1 1 75.9 32 32 48 24 REF 1 0 0 55 27.5 32 48 24 REF 1 0 1 75.9 37.5 32 48 24 REF 1 1 0 83.3 41.7 32 48 24 REF 1 1 1 68.5 34.25 32 48 24 REF Pentium is a trademark of Intel Corporation. 9169C-232RevB031897 ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate. ICS169C-232 Pin Descriptions PIN NUM BER PIN NAM E TYPE 1 VDD1 PWR 2 X1 IN 3 X2 OUT 4,11,16,22 GND PWR 6,7,9,10,15 CPU(2,3,4,5,8) OUT 5,12,13 CPU1, CPU6, CPU7 OUT 5,12,13 FS (0:2) IN DESCRIPTION Power for control logic and crystal oscillator circuit and 14.318 M Hz output XTAL or external reference frequency input. This input includes XTAL load capacitance and feedback bias for a 12-16MHz crystal, nominally 14.31818M Hz. External crystal load of 30pF to GND recommended for VDD power on faster than 2.0ms. XTAL output which includes XTAL load capacitance. External crystal load of 10pF to GND recommended for VDD power on faster than 2.0ms. Ground for control logic. Processor clock outputs which are a multiple of the input reference clock as shown in the preceding table. Processor clock outputs which are a multiple of the input reference clock as shown in the preceding table. Frequency multiplier select pins. See shared pin programming description later in this data sheet for further explanation. 350K* internal pull up. Power for CPU (1:6) clock buffers only. This VDD supply can be reduced to 2.5V for CPU (1:6) outputs. Power for CPU (7:8) clock buffers and internal PLL and Core logic. Must be nominal 3.3V (3.0 to 3.7V) BUS clock outputs which are a multiple of the input reference clock as shown in the preceding table. 8 VDD2 PWR 14 VDD3 PWR BUS(1:6) OUT 19 VDD4 PWR Power for BUS clock buffers BUS (1;6) 25 26 VDD5 24 MHz PWR OUT Power for fixed clock buffer (48 MHz, 24 MHz) Fixed 24 MHz clock (assuming a 14.31818 MHz REF frequency). 27 48 MHz OUT Fixed 48 MHz clock (assuming a 14.31818 MHz REF frequency). REF OUT Fixed 14.31818 M Hz clock (assuming a 14.31818 MHz REF frequency). IN Selection for synchronous or asynchronous bus clock operation. 350K* internal pull up. 17,18,20,21,23, 24 28 BSEL * The internal pull up will vary from 350K to 500K based on temperature 2 ICS169C-232 Shared Pin Operation Input/Output Pins Test Mode Operation The ICS9169C-232 includes a production test verification mode of operation. This requires that the FS0 and FS1 pins be programmed to a logic high and the FS2 pin be programmed to a logic low(see Shared Pin Operation section). In this mode the device will output the following frequencies. Shared Pin Operation - Input/Output, Pins 5, 28, 12 and 13 on the ICS9169C-232 serve as dual signal functions to the device. During initial power-up, they act as input pins. The logic level (voltage) that is present on these pins at this time is read and stored into a 4-bit internal data latch. At the end of Power-On reset, (see AC characteristics for timing values), the device changes the mode of operations for these pins to an output function. In this mode the pins produce the specified buffered clocks to external loads. Pin REF 48MHz 24MHz CPU (1:8) BSEL=1 BUS (1:6) BESEL = 0 To program (load) the internal configuration register for these pins, a resistor is connected to either the VDD (logic 1) power supply or the GND (logic 0) voltage potential. A 10 Kilohm(10K) resistor is used to provide both the solid CMOS programming voltage needed during the power-up programming period and to provide an insignificant load on the output clock during the subsequent operating period. Frequency REF REF/2 REF/4 REF2 REF/4 REF/3 Note: REF is the frequency of either the crystal connected between the devices X1and X2 or, in the case of a device being driven by an external reference clock, the frequency of the reference (or test) clock on the device’s X1 pin. Figs. 1 and 2 show the recommended means of implementing this function. In Fig. 1 either one of the resistors is loaded onto the board (selective stuffing) to configure the device’s internal logic. Figs. 2a and b provide a single resistor loading option where either solder spot tabs or a physical jumper header may be used. These figures illustrate the optimal PCB physical layout options. These configuration resistors are of such a large ohmic value that they do not effect the low impedance clock signals. The layouts have been optimized to provide as little impedance transition to the clock signal as possible, as it passes through the programming resistor pad(s). Fig. 1 3 ICS169C-232 Fig. 2b Fig. 2a Fig. 3 4 ICS169C-232 Technical Pin Function Descriptions VDD1 This is the power supply to the internal logic of the device as well as the following clock output buffers: BUS (1:6) This pin is the clock output that is intended to drive the systems plug-in card bus. The voltage swing of these clocks is controlled by the supply that is applied to the VDD pin of the device. See the Functionality table at the beginning of this data sheet for a list of the specific frequencies that this clock operates at and the selection codes that are necessary to produce these frequencies. A. REF clock output buffers B. BUS clock output buffers C. Fixed clock output buffers This pin may be operated at any voltage between 3.0 and 5.5 volts. Clocks from the listed buffers that it supplies will have a voltage swing from ground to this level. For the actual guaranteed high and low voltage levels of these clocks, please consult the AC parameter table in this data sheet. FS0, FS1, FS2 These pins control the frequency of the clocks at the CPU, CPUL, BUS, SDRAM, AGP and IOAPIC pins. See the Funtionality table at the beginning of this data sheet for a list of the specific frequencies that this clock operates at and the selection codes that are necessary to produce these frequencies. The device reads these pins at power-up and stores the programmed selection code in an internal data latch. (See programming section of this data sheet for configuration circuitry recommendations. GND This is the power supply ground return pin for the internal logic of the device as well as the following clock output buffers: A. REF clock output buffers B. BUS clock output buffers C. CPU clock output buffers BSEL When this pin is a logic 1, it will place the CPU clocks in the synchronous mode (running at half the frequency of the Ref). If this pin is a logic 0, it will be in the asynchronous mode for the CPU clocks and will operate at the preprogrammed fixed frequency rate. It is a shared pin and is programed the same way as the Frequency Select pins. X1 This pin serves one of two functions. When the device is used with a crystal, X1 acts as the input pin for the reference signal that comes from the discrete crystal. When the device is driven by an external clock signal, X1 is the device’ input pin for that reference clock. This pin also implements an internal crystal loading capacitor that is connected to ground. See the data tables for the value of the capacitor. VDD 2, 3 These are the power supply pins for the CPU clock buffers. By separating the clock power pins, each group can receive the appropriate power decoupling and bypassing necessary to minimize EMI and crosstalk between the individual signals. VDD2 can be reduced to 2.5V VDD for advanced processor clocks, which will bring CPU (1:6) outputs at 0 to 2.5V output swings. X2 This pin is used only when the device uses a Crystal as the reference frequency source. In this mode of operation, X2 is an output signal that drives (or excites) the discrete crystal. This pin also implements an internal crystal loading capacitor that is connected to ground. See the data tables for the value of the capacitor. 48 MHz This is a fixed frequency clock that is typically used to drive Super I/O peripheral device needs. CPU (1:8) This pin is the clock output that drives processor and other CPU related circuitry that require clocks which are in tight skew tolerance with the CPU clock. The voltage swing of these clocks is controlled by that which is applied to the VDD pin of the device. See the Functionality table at the beginning of this data sheet for a list of the specific frequencies this clock operates at and the selection codes that are necessary to produce these frequencies. 24 MHz This is a fixed frequency clock that is typically used to drive Keyboard controller clock needs. VDD4 This power pin supplies the BUS clock buffers. REF This is a fixed frequency clock that runs at the same frequency as the input reference clock (typically 14.31818 MHz) is and typically used to drive Video and ISA BUS requirements. VDD5 This power pin supplies the 48/24 MHz clocks. 5 ICS169C-232 Absolute Maximum Ratings Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0 V Logic Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND –0.5 V to VDD +0.5 V Ambient Operating Temperature . . . . . . . . . . 0°C to +70°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only and functional operation of the device at these or any other conditions above those listed in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. Electrical Characteristics at 3.3V VDD = 3.0 – 3.7 V, TA = 0 – 70 ° C unless otherwise stated DC Characteristics PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS Input Low Voltage VIL - - 0.2VDD V Input High Voltage VIH 0.7VDD - - V Input Low Current IIL VIN = 0V -28.0 -10.5 - µA Input High Current IIH VIN = VDD -5.0 - 5.0 µA Output Low Current1 IOL VOL = 0.8V; for CPU, BUS, REF CLKs 19.0 30.0 - mA 1 Output High Current IOH VOL = 2.0V; for CPU, BUS, REF CLKs - -38.0 -16.0 mA Output Low Current1 IOL VOL = 0.8V; for fixed CLKs 16.0 25.0 - mA 1 Output High Current IOH VOL = 2.0V; for fixed CLKs - -30.0 -14.0 mA Output Low Voltage1 VOL IOL = 10mA; for CPU, BUS, REF CLKs - 0.3 0.4 V 1 Output High Voltage VOH IOH = -15mA; for CPU, BUS, REF CLKs 2.4 2.8 - V Output Low Voltage1 VOL IOL = 8mA; for fixed CLKs - 0.3 0.4 V 1 Output High Voltage VOH IOH = -8mA; for fixed CLKs 2.4 2.8 - V Supply Current IDD @66.6 MHz; all outputs unloaded - 70 140 mA Note 1: Parameter is guaranteed by design and characterization. Not 100% tested in production. 6 ICS169C-232 Electrical Characteristics at 3.3V VDD = 3.0 – 3.7 V, TA = 0 – 70° C unless otherwise stated AC Characteristics PARAMETER SYMBOL Rise Time 1 Tr1 Fall Time 1 Tf1 Rise Time 1 Tr2 Fall Time 1 Tf2 Duty Cycle1 Dt TEST CONDITIONS 20pF load, 0.8 to 2.0V CPU & BUS 20pF load, 2.0 to 0.8V CPU & BUS 20pF load, 20% to 80% CPU & BUS 20pF load, 80% to 20% CPU & BUS 20pF load @ VOUT=1.4V CPU & BUS Clocks; Load=20pF, BSEL=1 CPU & BUS Clocks; Load=20pF, BSEL=1 MIN TYP MAX UNITS - 0.9 1.5 ns - 0.8 1.4 ns - 1.5 2.5 ns - 1.4 2.4 ns 45 50 60 % - 50 150 ps -250 - 250 ps Jitter, One Sigma1 Tj1s1 Jitter, Absolute1 T jab1 Jitter, One Sigma1 Tj1s2 REF & Fixed CLKs; Load=20pF - 1 3 % Jitter, Absolute1 T jab2 REF & Fixed CLKs; Load=20pF -5 2 5 % 12.0 14.318 16.0 MHz Input Frequency 1 Fi Logic Input Capacitance1 CIN Logic input pins - 5 - pF Crystal Oscillator Capacitance1 CINX X1, X2 pins - 18 - pF - 2.5 4.5 ms - 2.0 4.0 ms Power-on Time 1 ton Frequency Settling Time 1 ts From VDD=1.6V to 1st crossing of 66.6 MHz V DD supply ramp < 40ms From 1st crossing of acquisition to < 1% settling Clock Skew1 Tsk1 CPU to CPU; Load=20pF; @1.4V - 150 250 ps Clock Skew1 Tsk2 BUS & BUS; Load=20pF; @1.4V - 160 500 ps Clock Skew1 Tsk3 CPU to BUS; Load=20pF; @1.4V (CPU is early) 1 2.6 4 ns Note 1: Parameter is guaranteed by design and characterization. Not 100% tested in production. 7 ICS169C-232 SSOP Package SSOP SYMBOL A A1 A2 B C D E e H L N ∝ SOIC Package COMMON DIMENSIONS MIN. NOM. 0.068 0.002 0.066 0.010 0.004 0.205 0.301 0.025 0° 0.073 0.005 0.068 0.012 0.006 See Variations 0.209 0.0256 BSC 0.307 0.030 See Variations 4° SSOP VARIATIONS MAX. 0.078 0.008 0.070 0.015 0.008 14 16 20 24 28 30 D MIN. NOM. 0.239 0.239 0.278 0.318 0.397 0.397 MAX. 0.244 0.244 0.284 0.323 0.402 0.402 0.249 0.249 0.289 0.328 0.407 0.407 0.212 0.311 0.037 8° Ordering Information ICS9169CF-232 ICS9169CM-232 Example: ICS XXXX F - PPP SOIC Package (wide body) e = 0.05 BSC LEAD COUNT 14L 16L 18L 20L 24L 28L 32L DIMENSION L 0.354 0.404 0.454 0.504 0.604 0.704 0.804 8 ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate.