SN54ABT651, SN74ABT651 OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCBS083E – JANUARY 1991 – REVISED APRIL 1998 D D D D D D D State-of-the-Art EPIC-ΙΙB BiCMOS Design Significantly Reduces Power Dissipation ESD Protection Exceeds 2000 V Per MIL-STD-883, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) Latch-Up Performance Exceeds 500 mA Per JESD 17 Typical VOLP (Output Ground Bounce) < 1 V at VCC = 5 V, TA = 25°C High-Drive Outputs (–32-mA IOH, 64-mA IOL ) Multiplexed Real-Time and Stored Data Inverting Data Paths Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), and Thin Shrink Small-Outline (PW) Packages, Ceramic Chip Carriers (FK), and Plastic (NT) and Ceramic (JT) DIPs SN54ABT651 . . . JT PACKAGE SN74ABT651 . . . DB, DW, NT, OR PW PACKAGE (TOP VIEW) CLKAB SAB OEAB A1 A2 A3 A4 A5 A6 A7 A8 GND 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 VCC CLKBA SBA OEBA B1 B2 B3 B4 B5 B6 B7 B8 SN54ABT651 . . . FK PACKAGE (TOP VIEW) description A1 A2 A3 NC A4 A5 A6 5 4 3 2 1 28 27 26 25 6 24 7 23 8 22 9 21 10 20 19 11 12 13 14 15 16 17 18 OEBA B1 B2 NC B3 B4 B5 A7 A8 GND NC B8 B7 B6 These devices consist of bus-transceiver circuits, D-type flip-flops, and control circuitry arranged for multiplexed transmission of data directly from the data bus or from the internal storage registers. Output-enable (OEAB and OEBA) inputs are provided to control the transceiver functions. The select-control (SAB and SBA) inputs are provided to select whether real-time or stored data is transferred. A low input level selects real-time data, and a high input level selects stored data. Figure 1 illustrates the four fundamental bus-management functions that can be performed with the ’ABT651 devices. 1 OEAB SAB CLKAB NC VCC CLKBA SAB D NC – No internal connection Data on the A or B bus, or both, can be stored in the internal D flip-flops by low-to-high transitions at the appropriate clock (CLKAB or CLKBA) inputs, regardless of the select- or enable-control pins. When SAB and SBA are in the real-time transfer mode, it also is possible to store data without using the internal D-type flip-flops by simultaneously enabling OEAB and OEBA. In this configuration, each output reinforces its input. When all the other data sources to the two sets of bus lines are at high impedance, each set remains at its last state. To ensure the high-impedance state during power up or power down, OEBA should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver (B to A). OEAB should be tied to GND through a pulldown resistor; the minimum value of the resistor is determined by the current-sourcing capability of the driver (A to B). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC-ΙΙB is a trademark of Texas Instruments Incorporated. Copyright 1998, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ABT651, SN74ABT651 OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCBS083E – JANUARY 1991 – REVISED APRIL 1998 description (continued) The SN54ABT651 is characterized for operation over the full military temperature range of –55°C to 125°C. The SN74ABT651 is characterized for operation from –40°C to 85°C. FUNCTION TABLE INPUTS DATA I/O OPERATION OR FUNCTION OEAB OEBA CLKAB CLKBA SAB SBA A1–A8 B1–B8 L H H or L H or L X X Input Input Isolation L H ↑ ↑ X X Input Input Store A and B data X H ↑ H or L X Input Unspecified† Store A, hold B H H ↑ ↑ X X‡ X Input Output Store A in both registers L X H or L ↑ X Unspecified† Input Hold A, store B L L ↑ ↑ X X X‡ Output Input Store B in both registers L L X X X L Output Input Real-time B data to A bus L L X H or L X H Output Input Stored B data to A bus H H X X L X Input Output Real-time A data to B bus H H H or L X H X Input Output Stored A data to B bus H L H or L H or L H H Output Output Stored A data to B bus and stored B data to A bus † The data output functions may be enabled or disabled by a variety of level combinations at OEAB or OEBA. Data input functions are always enabled; i.e., data at the bus terminals is stored on every low-to-high transition of the clock inputs. ‡ When select control is low, clocks can occur simultaneously if allowances are made for propagation delays from A to B (B to A) plus setup and hold times. When select control is high, clocks must be staggered to load both registers. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ABT651, SN74ABT651 OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS 1 23 2 CLKAB CLKBA SAB X X X 22 SBA L 21 OEBA H X H 1 23 2 CLKAB CLKBA SAB ↑ X ↑ X ↑ ↑ 23 CLKBA X 2 SAB L X X X BUS A BUS A 3 1 CLKAB X 22 SBA X REAL-TIME TRANSFER BUS A TO BUS B BUS B REAL-TIME TRANSFER BUS B TO BUS A OEAB X L L BUS B 3 21 OEAB OEBA H H BUS B 3 21 OEAB OEBA L L BUS A BUS A BUS B SCBS083E – JANUARY 1991 – REVISED APRIL 1998 22 3 21 1 23 2 22 SBA OEAB H OEBA L CLKAB CLKBA SAB SBA H or L H or L H H X X X TRANSFER STORED DATA TO A AND/OR B STORAGE FROM A, B, OR A AND B Pin numbers are for the DB, DW, JT, NT, and PW packages. Figure 1. Bus-Management Functions POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54ABT651, SN74ABT651 OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCBS083E – JANUARY 1991 – REVISED APRIL 1998 logic symbol† OEBA OEAB CLKBA SBA CLKAB SAB A1 21 3 23 22 1 EN1 [BA] EN2 [AB] C4 G5 2 C6 G7 4 ≥1 1 7 1 A3 A4 A5 A6 A7 A8 4D ≥1 B1 2 7 5 19 6 18 7 17 8 16 9 15 10 14 11 13 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the DB, DW, JT, NT, and PW packages. 4 20 5 1 6D A2 5 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 B2 B3 B4 B5 B6 B7 B8 SN54ABT651, SN74ABT651 OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCBS083E – JANUARY 1991 – REVISED APRIL 1998 logic diagram (positive logic) OEBA OEAB CLKBA SBA CLKAB SAB 21 3 23 22 1 2 One of Eight Channels 1D C1 4 A1 20 1D B1 C1 To Seven Other Channels Pin numbers shown are for the DB, DW, JT, NT, and PW packages. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54ABT651, SN74ABT651 OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCBS083E – JANUARY 1991 – REVISED APRIL 1998 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (except I/O ports) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Voltage range applied to any output in the high or power-off state, VO . . . . . . . . . . . . . . . . . . . –0.5 V to 5.5 V Current into any output in the low state, IO: SN54ABT651 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ABT651 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 2): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104°C/W DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81°C/W NT package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67°C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51, except for through-hole packages, which use a trace length of zero. recommended operating conditions (see Note 3) SN54ABT651 MAX MIN MAX 4.5 5.5 4.5 5.5 VCC VIH Supply voltage VIL VI Low-level input voltage IOH IOL High-level output current VCC –24 Low-level output current ∆t/∆v Input transition rise or fall rate High-level input voltage SN74ABT651 MIN 2 2 0.8 Input voltage 0 UNIT V V 0.8 V VCC –32 V mA 48 64 mA 5 5 ns/V 0 TA Operating free-air temperature –55 125 –40 85 °C NOTE 3: All unused pins (control or I/O) of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ABT651, SN74ABT651 OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCBS083E – JANUARY 1991 – REVISED APRIL 1998 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH TEST CONDITIONS VCC = 4.5 V, VCC = 4.5 V, II = –18 mA IOH = –3 mA VCC = 5 V, VCC = 4 4.5 5V VOL VCC = 4 4.5 5V MIN SN54ABT651 MIN –1.2 MAX SN74ABT651 MIN –1.2 MAX –1.2 2.5 2.5 2.5 IOH = –3 mA IOH = –24 mA 3 3 3 2 2 IOH = –32 mA IOL = 48 mA 2* IOL = 64 mA VCC = 5 5.5 5V V, VI = VCC or GND IOZH‡ IOZL‡ VCC = 5.5 V, VCC = 5.5 V, VO = 2.7 V VO = 0.5 V Ioff VCC = 0, VCC = 5.5 V, VO = 5.5 V VI or VO ≤ 4.5 V IO§ VCC = 5.5 V, ICC VCC = 5.5 V, IO = 0, VI = VCC or GND VO = 2.5 V Outputs high A or B ports ICEX 0.55 0.55* 0.55 mV ±1 ±1 ±100 ±100 ±100 50 50 50 µA –50 –50 Outputs high 50 –100 –180 Outputs low Outputs disabled VCC = 5.5 V, One input at 3.4 V, Other inputs at VCC or GND ∆ICC¶ Ci Control inputs Cio A or B ports VI = 2.5 V or 0.5 V VO = 2.5 V or 0.5 V V ±1 ±100 –50 V V 100 Control inputs UNIT 2 0.55 Vhys II TA = 25°C TYP† MAX 50 –50 –180 –50 µA –50 µA ±100 µA 50 µA –180 mA 250 250 250 µA 30 30 30 mA 250 250 250 µA 1.5 1.5 1.5 mA 6 pF 7.5 pF * On products compliant to MIL-PRF-38535, this parameter does not apply. † All typical values are at VCC = 5 V. ‡ The parameters IOZH and IOZL include the input leakage current. § Not more than one output should be tested at a time, and the duration of the test should not exceed one second. ¶ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 2) VCC = 5 V, TA = 25°C MIN MAX SN54ABT651 MIN 125 MAX SN74ABT651 MIN 125 UNIT MAX fclock tw Clock frequency Pulse duration, CLK high or low 4 4 4 125 MHz ns tsu th Setup time, A or B before CLKAB↑ or CLKBA↑ 3 3 3 ns Hold time, A or B after CLKAB↑ or CLKBA↑ 0 0 0 ns PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 SN54ABT651, SN74ABT651 OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCBS083E – JANUARY 1991 – REVISED APRIL 1998 switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Figure 2) PARAMETER fmax tPLH tPHL tPLH tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ tPZH tPZL tPHZ FROM (INPUT) TO (OUTPUT) VCC = 5 V, TA = 25°C MIN TYP SN54ABT651 MAX 125 CLKBA or CLKAB A or B A or B B or A SAB or SBA† A or B OEBA A OEBA A OEAB B MIN MAX 125 MHz 4 5.1 2.2 5.9 2.2 5.6 1.7 4 5.1 1.7 5.9 1.7 5.6 1.5 4 5.1 1.5 6.4 1.5 6.2 1.5 3.3 4.6 1.5 5.6 1.5 5.4 1.5 4 5.1 1.5 6.8 1.5 6.5 1.5 3.6 4.9 1.5 6.2 1.5 5.9 1.3 3.6 4.6 1.3 5.9 1.3 5.8 2.5 5.7 6.8 2.5 8.9 2.5 8.5 1.5 3.2 4.5 1.5 6.2 1.5 5 1.5 3 3.8 1.5 4.3 1.5 4.1 1.8 4.3 6.1 1.8 6.7 1.8 6.5 2.9 5.5 6.5 2.9 7.6 2.9 7.4 1.5 5.5 1.5 5.1 • DALLAS, TEXAS 75265 UNIT MAX 2.2 PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 MIN 125 1.5 3.3 4.5 1.5 6.5 OEAB B tPLZ 1.5 3.4 4.4 1.5 5.2 † These parameters are measured with the internal output state of the storage register opposite that of the bus input. 8 SN74ABT651 ns ns ns ns ns ns ns SN54ABT651, SN74ABT651 OCTAL BUS TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCBS083E – JANUARY 1991 – REVISED APRIL 1998 PARAMETER MEASUREMENT INFORMATION 7V S1 500 Ω From Output Under Test Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 7V Open LOAD CIRCUIT 3V Timing Input 1.5 V 0V tw tsu 3V Input 1.5 V 1.5 V th 3V Data Input 1.5 V 1.5 V 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES 3V 1.5 V Input 1.5 V 0V VOH 1.5 V Output 1.5 V VOL VOH Output 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 1.5 V 0V tPLZ Output Waveform 1 S1 at 7 V (see Note B) tPLH tPHL 1.5 V tPZL tPHL tPLH 3V Output Control Output Waveform 2 S1 at Open (see Note B) 1.5 V tPZH 3.5 V VOL + 0.3 V VOL tPHZ 1.5 V VOH – 0.3 V VOH ≈0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. Figure 2. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 PACKAGE OPTION ADDENDUM www.ti.com 21-Nov-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN74ABT651DBLE OBSOLETE SSOP DB 24 SN74ABT651DBR ACTIVE SSOP DB 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT651DBRE4 ACTIVE SSOP DB 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT651DW ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT651DWE4 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT651DWR ACTIVE SOIC DW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT651DWRE4 ACTIVE SOIC DW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT651NSR ACTIVE SO NS 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT651NSRE4 ACTIVE SO NS 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ABT651NT ACTIVE PDIP NT 24 15 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC SN74ABT651NTE4 ACTIVE PDIP NT 24 15 Pb-Free (RoHS) CU NIPDAU Level-NC-NC-NC TBD Lead/Ball Finish Call TI MSL Peak Temp (3) Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated