ISO2-CMOS MT9162 5 Volt Single Rail Codec Advance Information DS5178 Features ISSUE 4 August 1999 Ordering Information • • • • • • • • • • Single 5 volt supply Programmable µ−law/A-law Codec and filters Fully differential output driver SSI digital interface SSI speed control via external pins CSLO-CSL2 Individual transmit and receive mute controls 0dB gain in receive path 6dB gain in transmit path Low power operation ITU-T G.714 compliant MT9162AE MT9162AS MT9162AN 20 Pin Plastic DIP (300 mil) 20 Pin SOIC 20 Pin SSOP -40°C to +85°C Description The MT9162 5V single rail Codec incorporates a built-in Filter/Codec, transmit anti-alias filter, a reference voltage and bias source. The device supports both A-law and µ-law requirements. Applications • • • The analog interface is capable of driving a 20k ohm load. Cellular radio sets Local area communications stations Line cards The MT9162 is fabricated in Mitel's ISO2-CMOS technology ensuring low power consumption and high reliability. FILTER/CODEC GAIN AIN+ VDD VSS ENCODER 6dB DECODER 0 dB VBias VRef AINAnalog Interface AOUT + AOUT - Din Dout STB Timing PCM Serial Interface CLOCKin Control PWRST IC A/µ CSL0 CSL1 CSL2 RXMute TXMute Figure 1 - Functional Block Diagram 7-161 MT9162 Advance Information VBias VRef PWRST IC A/µ RXMUTE TXMUTE CSL0 CSL1 CSL2 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 AIN+ AINVSS AOUT + AOUT VDD CLOCKin STB Din Dout 20 PIN PDIP/SOIC/SSOP Figure 2 - Pin Connections Pin Description Pin # Name 1 VBias Bias Voltage (Output). (VDD/2) volts is available at this pin for biasing external amplifiers. Connect 0.1 µ F capacitor to VSS. Connect 1 µF capacitor to Vref. 2 VRef Reference Voltage for Codec (Output). Nominally [(VDD/2)-1.9] volts. Used internally. Connect 0.1 µ F capacitor to VSS. Connect 1 µF capacitor to VBias 3 Description PWRST Power-up Reset. Resets internal state of device via Schmitt Trigger input (active low). 4 IC Internal Connection. Tie externally to VSS for normal operation. 5 A/µ A/µ Law Selection. CMOS level compatable input pin governs the companding law used by the device. A-law selected when pin tied to VDD or µ-law selected when pin tied to VSS. 6 RXMute Receive Mute. When 1, the transmit PCM is forced to negative zero code. When 0, normal operation. CMOS level compatible. 7 TXMute Transmit Mute. When 1, the transmit PCM is forced to negative zero code. When 0, normal operation. CMOS level compatible. 8 9 10 CSL0 CSL1 CSL2 Clock Speed Select. These pins are used to program the speed of the SSI mode as well as the conversion rate between the externally supplied MCL clock and the 512 kHz clock required by the filter/codec. Refer to Table 2 for details. CMOS level compatible. 11 Dout Data Output. A tri-state digital output for 8-bit wide channel data being sent to the Layer 1 device. Data is shifted out via the pin concurrent with the rising edge of BCL during the timeslot defined by STB. 12 Din Data Input. A digital input for 8-bit wide data from the layer 1 device. Data is sampled on the falling edge of BCL during the timeslot defined by STB. CMOS level compatible. 13 STB Data Strobe. This input determines the 8-bit timeslot used by the device for both transmit and receive data. This active high signal has a repetition rate of 8 kHz. CMOS level compatible. 14 CLOCKin Clock (Input). The clock provided to this input pin is used by the internal device functions. Connect bit clock to this pin when it is 512 kHz or greater. Connect a 4096 kHz clock to this pin when the bit clock is 128 kHz or 256 kHz. CMOS level compatible. 15 VDD Positive Power Supply. Nominally 5 volts. 16 AOUT- 17 AOUT+ Non-Inverting Analog Output. (balanced). Inverting Analog Output. (balanced). 18 VSS Ground. Nominally 0 volts. 19 Ain- Inverting Analog Input. No external anti-aliasing is required. 20 Ain+ Non-Inverting Analog Input. Non-inverting input. No external anti-aliasing is required. 7-162 MT9162 Advance Information Overview The 5V single rail Codec features complete Analog/ Digital and Digital/Analog conversion of audio signals (Filter/Codec) and an analog interface to a standard analog transmitter and receiver (Analog Interface). The receiver amplifier is capable of driving a 20k ohm load. Functional Description Filter/Codec Companding law selection for the Filter/Codec is provided by the A/ µ companding control pin. Table 1 illustrates these choices. ITU-T (G.711) Code µ -Law A-Law + Full Scale 1000 0000 1010 1010 + Zero 1111 1111 1101 0101 -Zero (quiet code) 0111 1111 0101 0101 - Full Scale 0000 0000 0010 1010 Table 1: Law Selection The Filter/Codec block implements conversion of the analog 0-3.3 kHz speech signals to/from the digital domain compatible with 64 kb/s PCM B-Channels. Selection of companding curves and digital code assignment are programmable. These are ITU-T G.711 A-law or µ-Law, with true-sign/Alternate Digit Inversion. The Filter/Codec block also implements a transmit audio path gain in the analog domain. Figure 3 depicts the nominal half-channel for the MT9162. The internal architecture is fully differential to provide the best possible noise rejection as well as to allow a wide dynamic range from a single 5 volt supply design. This fully differential architecture is continued into the analog interface section to provide full chip realization of these capabilities for the external functions. A reference voltage (VRef), for the conversion requirements of the Codec section, and a bias voltage (VBias), for biasing the internal analog sections, are both generated on-chip. VBias is also brought to an external pin so that it may be used for biasing external gain setting amplifiers. A 0.1µF capacitor must be connected from VBias to analog ground at all times. Likewise, although VRef may only be used internally, a 0.1µF capacitor from the VRef pin to ground is required at all times. The analog ground reference point for these two capacitors must be physically the same point. To facilitate this the VRef and VBias pins are situated on adjacent pins. The transmit filter is designed to meet ITU-T G.714 specifications. An anti-aliasing filter is included. This is a second order lowpass implementation with a corner frequency at 25 kHz. Analog Interfaces Standard interfaces are provided by the MT9162. These are: • The analog inputs (transmitter), pins AIN+/AIN-. The maximum peak to peak input is 3.667Vpp µ−law and across AIN+/AIN- 3.8Vpp A-law. • The analog outputs (receiver), pins AOUT+/ AOUT-. This internally compensated fully differential output driver is capable of driving a load of 20k ohms. PCM Serial Interface A serial link is required to transport data between the MT9162 and an external digital transmission device. The MT9162 utilizes the strobed data interface found on many standard Codec devices. This interface is commonly referred to as Simple Serial Interface (SSI). The required mode of operation is selected via the CSL2-0 control pins. See Table 2 for selections based in CSL2-0 pin settings. Quiet Code The PCM serial port can be made to send quiet code to the decoder and receive filter path by setting the RxMute pin high. Likewise, the PCM serial port will send quiet code in the transmit path when the The receive filter is designed to meet ITU-T G.714 specifications. Filter response is peaked to compensate for the sinx/x attenuation caused by the 8 kHz sampling rate. 7-163 MT9162 Advance Information CSL2 CSL1 CSL0 External Clock Bit Rate (kHz) 1 0 0 128 4096 1 0 1 256 4096 0 0 0 512 512 0 0 1 1536 1536 0 1 0 2048 2048 0 1 1 4096 4096 CLOCKin (kHz) In SSI mode the MT9162 supports only B-Channel operation. Hence, in SSI mode transmit and receive B-Channel data are always in the channel defined by the STB input. The data strobe input STB determines the 8-bit timeslot used by the device for both transmit and receive data. This is an active high signal with an 8 kHz repetition rate. Table 2: Bit Clock Rate Selection TxMute pin is high. When either of these pins are low their respective paths function normally. The -Zero entry of Table 1 is used for the quiet code definition. SSI Mode The SSI BUS consists of input and output serial data streams named Din and Dout respectively, a Clock input signal (CLOCKin), and a framing strobe input (STB). A 4.096 MHz master clock is also required for SSI operation if the bit clock is less than 512 kHz. Serial Receive Filter Gain 0 dB Decoder 2.05 dB PCM Applications where Bit Clock (BCL) is below 512 kHz are designated as asynchronous. The MT9162 will re-align its internal clocks to allow operation when the external master and bit clocks are asynchronous. Control pins CSL2, CSL1 and CSL0 are used to program the bit rates. Aout + PCM Dout SSI operation is separated into two categories based upon the data rate of the available bit clock. If the bit clock is 512 kHz or greater then it is used directly by the internal MT9162 functions allowing synchronous operation. If the available bit clock is 128 kHz or 256 kHz, then a 4096 kHz master clock is required to derive clocks for the internal MT9162 functions. Filter/Codec and Analog Interface Port Din The timing requirements for SSI are shown in Figures 5 & 6. Encoder -2.05 dB Transmit Filter Transmit Filter Gain Gain 0 to0dB +7 dB (1 dB steps) Transmit Gain -0.37 dB -2.05 dB Receiver Driver Transmit Gain 8.42 dB Internal To Device Figure 3 - Audio Gain Partitioning 7-164 Aout- AIN+ AIN- 20kΩ Analog Input External To Device MT9162 Advance Information For synchronous operation, data is sampled from Din, on the falling edge of BCL during the time slot defined by the STB input. Data is made available, on Dout, on the rising edge of BCL during the time slot defined by the STB input. Dout is tri-stated at all times when STB is not true. If STB is valid, then quiet code will be transmitted on Dout during the valid strobe period. There is no frame delay through the PCM serial circuit for synchronous operation. Applications Figure 4 shows the MT9162 in a line card application. For asynchronous operation Dout and Din are as defined for synchronous operation except that the allowed output jitter on Dout is larger. This is due to the resynchronization circuitry activity and will not affect operation since the bit cell period at 128 kb/s and 256 kb/s is relatively large. There is a one frame delay through the PCM serial circuit for asynchronous operation. Refer to the specifications of Figures 5 & 6 for both synchronous and asynchronous SSI timing. PWRST While the MT9162 is held in PWRST no device control or functionality is possible. 0.1 µF VBias ( Typical External Gain AV= 5-10 ) Input from Subscriber Line Interface 1 µF 0.1 µF +5V 1 2 100k 100k 1k 100k 3 4 5 A/µ RxMUTE TxMUTE MT9162 6 7 8 9 10 1k 100k 1k 100k CS0 1k 100k CS1 20 19 18 17 16 15 14 13 12 11 Out to Subscriber Line Interface +5V 1k 100k 1k CS2 DC to DC Converter +5V Din Lin MT8972 From Digital Phone ZT DNIC Dout Frame Pulse Twisted Pair Lout Clock Figure 4 - Line Card Application 7-165 MT9162 Advance Information Absolute Maximum Ratings† Parameter Symbol Min Max Units VDD - VSS - 0.3 7 V VI/VO VSS - 0.3 VDD + 0.3 V ± 20 mA + 150 °C 1 Supply Voltage 2 Voltage on any I/O pin 3 Current on any I/O pin (transducers excluded) II/IO 4 Storage Temperature TS - 65 5 Power Dissipation (package) PD 750 † Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. Recommended Operating Conditions Characteristics mW Voltages are with respect to VSS unless otherwise stated Sym Min Typ Max Units 5 5.25 V 1 Supply Voltage VDD 4.75 2 CMOS Input Voltage (high) VIHC 4.5 VDD V 3 CMOS Input Voltage (low) VILC VSS 0.5 V 4 Operating Temperature TA - 40 + 85 °C Test Conditions Power Characteristics Characteristics 1 Static Supply Current (clock disabled) 2 Dynamic Supply Current: Total all functions enabled Sym Min Typ Max Units IDDC1 4 20 µA Outputs unloaded, Input signals static, not loaded IDDFT 7.0 10 mA See Note 1 Note 1: Power delivered to the load is in addition to the bias current requirements. 7-166 Test Conditions MT9162 Advance Information DC Electrical Characteristics† - Voltages are with respect to ground (VSS) Characteristics Sym Min 3.5 Typ‡ unless otherwise stated. Max Units Test Conditions 1 Input HIGH Voltage CMOS inputs VIHC V 2 Input LOW Voltage CMOS inputs VILC 3 VBias Voltage Output VBias VDD/2 V Max. Load = 10kΩ 4 VRef Output Voltage VRef VDD/2-1.9 V No load 5 Input Leakage Current IIZ 0.1 µA VIN=VDD to VSS 6 Positive Going Threshold Voltage (PWRST only) Negative Going Threshold Voltage (PWRST only) VT+ 7 Output HIGH Current IOH 3 7 mA VOH = 0.9*VDD See Note 1 8 Output LOW Current IOL 5 10 mA VOL = 0.1*VDD See Note 1 9 Output Leakage Current IOZ 0.01 µA VOUT = VDD and VSS 10 Output Capacitance Co 15 pF 11 Input Capacitance Ci 10 pF 1.5 10 3.7 V V VT- 1.3 10 V † DC Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing. * Note 1 - Magnitude measurement, ignore signs. Clockin Tolerance Characteristics† Characteristics 1 CLOCKin Frequency (Asynchronous Mode) Min Typ‡ Max Units 4095.6 4096 4096.4 kHz Test Conditions (i.e., 100 ppm) † AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing. 7-167 MT9162 Advance Information AC Characteristics† for A/D (Transmit) Path - 0dBm0 = ALo3.17 - 3.17dB = 1.773Vrms for µ-Law and 0dBm0 = ALo3.14 - 3.14dB = 1.843Vrms for A-Law, at the Codec. (VRef=0.6 volts and VBias=2.5 volts.) Characteristics 1 Analog input equivalent to overload decision 2 Absolute half-channel gain Sym Min ALi3.17 ALi3.14 Typ‡ Max 7.334 7.6 Units Vp-p Vp-p Test Conditions µ-Law A-Law Both at Codec 6.8 dB Transmit filter gain=0dB setting. @1020Hz 0.3 0.6 1.6 dB dB dB 3 to -40 dBm0 -40 to -50 dBm0 -50 to -55 dBm0 dB dB dB 0 to -30 dBm0 -40 dBm0 -45 dBm0 AIN ± to Dout GAX1 5.2 3 Gain tracking vs. input level ITU-T G.714 Method 2 GTX -0.3 -0.6 -1.6 4 Signal to total Distortion vs. input level. ITU-T G.714 Method 2 DQX 35 29 24 5 Transmit Idle Channel Noise NCX NPX 6 Gain relative to gain at <50Hz 60Hz 200Hz 300 - 3000 Hz 3000 - 3400 Hz 4000 Hz >4600 Hz GRX 7 Absolute Delay DAX 360 µs at frequency of minimum delay 8 Group Delay relative to DAX DDX 750 380 130 750 µs µs µs µs 500-600 Hz 600 - 1000 Hz 1000 - 2600 Hz 2600 - 2800 Hz 9 Power Supply Rejection f=1020 Hz f=0.3 to 3 kHz f=3 to 4 kHz f=4 to 50 kHz 6.0 8.5 -71 -45 -0.25 -0.9 -23 -40 PSSR PSSR1 PSSR2 PSSR3 37 37 40 35 40 12 -69 dBrnC0 dBm0p -25 -30 0.0 0.25 0.25 -12.5 -25 dB dB dB dB dB dB dB dB dB dB dB µ-Law A-Law ±100mV peak signal on VDD µ-law PSSR1-3 not production tested † AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing. 7-168 MT9162 Advance Information AC Characteristics† for D/A (Receive) Path - 0dBm0 = ALo3.17 - 3.17dB = 1.773Vrms for µ-Law and 0dBm0 = ALo3.14 - 3.14dB = 1.843Vrms for A-Law, at the Codec. (VRef=0.6 volts and VBias=2.5 volts.) Sym 1 Analog output at the Codec full scale ALo3.17 ALo3.14 2 Absolute half-channel gain. Din to AOUT± GAR1 -0.8 3 Gain tracking vs. input level ITU-T G.714 Method 2 GTR -0.3 -0.6 -1.6 4 Signal to total distortion vs. input level. ITU-T G.714 Method 2 GQR 35 29 24 5 Receive Idle Channel Noise NCR NPR 6 Gain relative to gain at 1020Hz 200Hz 300 - 3000 Hz 3000 - 3400 Hz 4000 Hz >4600 Hz GRR 7 Absolute Delay DAR 240 µs at frequency of min. delay 8 Group Delay relative to DAR DDR 750 380 130 750 µs µs µs µs 500-600 Hz 600 - 1000 Hz 1000 - 2600 Hz 2600 - 2800 Hz 9 Crosstalk CTRT CTTR dB dB G.714.16 ITU-T D/A to A/D A/D to D/A Min Typ‡ Characteristics Max Units 7.225 7.481 0 7 -84 -0.25 -0.90 Vp-p Vp-p Test Conditions µ-Law A-Law 0.8 dB @1020Hz 0.3 0.6 1.6 dB dB dB 3 to -40 dBm0 -40 to -50 dBm0 -50 to -55 dBm0 dB dB dB 0 to -30 dBm0 -40 dBm0 -45 dBm0 10 -80 dBrnC0 dBm0p 0.25 0.25 0.25 -12.5 -25 dB dB dB dB dB -74 -80 µ-Law A-Law † AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing. Electrical Characteristics† for Analog Outputs Characteristics Sym Min 20k 1 Load impedance at Output EZL 2 Allowable output capacitive load ECL 3 Analog output harmonic distortion ED Typ‡ Max Units ohms 20 0.5 Test Conditions across AOUT± pF each pin: AOUT+, AOUT- % 20k ohms load across AOUT± VO≤693mVRMS † Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing. 7-169 MT9162 Advance Information Electrical Characteristics† for Analog Inputs Characteristics 1 2 Sym Min Typ‡ Max Units Test Conditions Maximum input voltage without overloading Codec across AIN+/AIN- VIOLH Input Impedance ZI 2.90 3.00 Vp-p 50 kΩ A/µ = 0 A/µ = 1 AIN+/AIN- to VSS † Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25 °C and are for design aid only: not guaranteed and not subject to production testing. AC Electrical Characteristics† - SSI BUS Synchronous Timing (see Figure 5) Characteristics Sym Min 1 BCL Clock Period tBCL 244 2 BCL Pulse Width High tBCLH 3 BCL Pulse Width Low Typ‡ Max Units Test Conditions 1953 ns BCL=4096 kHz to 512 kHz 122 ns BCL=4096 kHz tBCLL 122 ns BCL=4096 kHz 4 BCL Rise/Fall Time tR/tF ns Note 1 5 Strobe Pulse Width tENW 20 8 x tBCL ns Note 1 6 Strobe setup time before BCL falling tSSS 70 tBCL-80 ns 7 Strobe hold time after BCL falling tSSH 80 tBCL-80 ns 8 Dout High Impedance to Active Low from Strobe rising tDOZL 50 ns CL=150 pF, RL=1K 9 Dout High Impedance to Active High from Strobe rising tDOZH 50 ns CL=150 pF, RL=1K 10 Dout Active Low to High Impedance from Strobe falling tDOLZ 50 ns CL=150 pF, RL=1K 11 Dout Active High to High Impedance from Strobe falling tDOHZ 50 ns CL=150 pF, RL=1K 12 Dout Delay (high and low) from BCL rising tDD 50 ns CL=150 pF, RL=1K 13 Din Setup time before BCL falling tDIS 20 ns 14 Din Hold Time from BCL falling tDIH 50 ns † Timing is over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. NOTE 1: Not production tested, guaranteed by design. 7-170 MT9162 Advance Information tBCLH tBCL tR tF CLOCKin 70% (BCL) 30% tBCLL tDIS Din tDIH 70% 30% tDD tDOZL Dout 70% 30% tDOZH STB tDOLZ tDOHZ tSSH tENW tSSS 70% 30% NOTE: Levels refer to % VDD (CMOS I/O) Figure 5 - SSI Synchronous Timing Diagram AC Electrical Characteristics† - SSI BUS Asynchronous Timing (note 1) (see Figure 6) Characteristics 1 Bit Cell Period Sym Min TDATA Typ‡ Max 7812 3906 Units ns ns Test Conditions BCL=128 kHz BCL=256 kHz Tj 600 ns 3 Bit 1 Dout Delay from STB going high tdda1 Tj+600 ns CL=150 pF, RL=1K 4 Bit 2 Dout Delay from STB going high tdda2 600+ TDATA-Tj 600+ TDATA 600 + TDATA+Tj ns CL=150 pF, RL=1K 5 Bit n Dout Delay from STB going high tddan 600 + (n-1) x TDATA-Tj 600 + (n-1) x TDATA 600 + (n-1) x TDATA+Tj ns CL=150 pF, RL=1K n=3 to 8 TDATA1 TDATA-Tj TDATA+Tj ns 7 Din Bit n Data Setup time from STB rising tSU TDATA\2 +500ns-Tj +(n-1) x TDATA ns 8 Din Data Hold time from STB rising tho TDATA\2 +500ns+Tj +(n-1) x TDATA ns 2 Frame Jitter 6 Bit 1 Data Boundary n=1-8 † Timing is over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. 7-171 MT9162 Advance Information Tj STB 70% 30% tdda2 tdha1 tdda1 Dout 70% Bit 1 30% Bit 2 Bit 3 TDATA TDATA1 tho tsu Din 70% D2 D1 30% TDATA/2 TDATA D3 TDATA NOTE: Levels refer to % VDD (CMOS I/O) Figure 6 - SSI Asynchronous Timing Diagram 7-172 Package Outlines Pin 1 E A C L H e Notes: 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) 4) Ref. JEDEC Standard M0-150/M0118 for 48 Pin 5) A & B Maximum dimensions include allowable mold flash D A2 A1 B 20-Pin 24-Pin 28-Pin 48-Pin Dim Min A A1 0.002 (0.05) B 0.0087 (0.22) C Max Min Max 0.079 (2) - 0.079 (2) 0.002 (0.05) 0.013 (0.33) 0.0087 (0.22) 0.008 (0.21) Min Max Min Max 0.079 (2) 0.095 (2.41) 0.110 (2.79) 0.008 (0.2) 0.016 (0.406) 0.008 (0.2) 0.0135 (0.342) 0.002 (0.05) 0.013 (0.33) 0.0087 (0.22) 0.008 (0.21) 0.013 (0.33) 0.008 (0.21) 0.010 (0.25) D 0.27 (6.9) 0.295 (7.5) 0.31 (7.9) 0.33 (8.5) 0.39 (9.9) 0.42 (10.5) 0.62 (15.75) 0.63 (16.00) E 0.2 (5.0) 0.22 (5.6) 0.2 (5.0) 0.22 (5.6) 0.2 (5.0) 0.22 (5.6) 0.291 (7.39) 0.299 (7.59) e 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) A2 0.065 (1.65) 0.073 (1.85) 0.065 (1.65) 0.073 (1.85) 0.065 (1.65) 0.073 (1.85) 0.089 (2.26) 0.099 (2.52) H 0.29 (7.4) 0.32 (8.2) 0.29 (7.4) 0.32 (8.2) 0.29 (7.4) 0.32 (8.2) 0.395 (10.03) 0.42 (10.67) L 0.022 (0.55) 0.037 (0.95) 0.022 (0.55) 0.037 (0.95) 0.022 (0.55) 0.037 (0.95) 0.02 (0.51) 0.04 (1.02) Small Shrink Outline Package (SSOP) - N Suffix General-11 Package Outlines Pin 1 E A C L H e D L 4 mils (lead coplanarity) Notes: 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) 4) A & B Maximum dimensions include allowable mold flash A1 B DIM 16-Pin 18-Pin 20-Pin 24-Pin 28-Pin Min Max Min Max Min Max Min Max Min Max A 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) A1 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) B 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.030 (0.51) 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.020 (0.51) C 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) D 0.398 (10.1) 0.413 (10.5) 0.447 (11.35) 0.4625 (11.75) 0.496 (12.60) 0.512 (13.00) 0.5985 (15.2) 0.614 (15.6) 0.697 (17.7) 0.7125 (18.1) E 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) e 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) H 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) L 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) Lead SOIC Package - S Suffix NOTES: 1. Controlling dimensions in parenthesis ( ) are in millimeters. 2. Converted inch dimensions are not necessarily exact. General-7 Package Outlines 3 2 1 E1 E n-2 n-1 n D A2 A L C eA b2 e eC eB b Notes: D1 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) Plastic Dual-In-Line Packages (PDIP) - E Suffix DIM 8-Pin 16-Pin 18-Pin 20-Pin Plastic Plastic Plastic Plastic Min A Max Min 0.210 (5.33) Max Min 0.210 (5.33) Max Min 0.210 (5.33) Max 0.210 (5.33) A2 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) b2 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) C 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014(0.356) 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014 (0.356) D 0.355 (9.02) 0.400 (10.16) 0.780 (19.81) 0.800 (20.32) 0.880 (22.35) 0.920 (23.37) 0.980 (24.89) 1.060 (26.9) D1 0.005 (0.13) E 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) E1 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.005 (0.13) 0.005 (0.13) 0.005 (0.13) e 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) eA 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62) L 0.115 (2.92) eB eC 0.150 (3.81) 0.115 (2.92) 0.430 (10.92) 0 0.060 (1.52) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52) NOTE: Controlling dimensions in parenthesis ( ) are in millimeters. General-8 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.430 (10.92) 0 0.060 (1.52) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52) Package Outlines 3 2 1 E1 E n-2 n-1 n D α A2 A L C eA b2 e eB b Notes: D1 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) Plastic Dual-In-Line Packages (PDIP) - E Suffix DIM 22-Pin 24-Pin 28-Pin 40-Pin Plastic Plastic Plastic Plastic Min A Max Min 0.210 (5.33) Max Min 0.250 (6.35) Max Min 0.250 (6.35) Max 0.250 (6.35) A2 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) b2 0.045 (1.15) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) C 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) D 1.050 (26.67) 1.120 (28.44) 1.150 (29.3) 1.290 (32.7) 1.380 (35.1) 1.565 (39.7) 1.980 (50.3) 2.095 (53.2) D1 0.005 (0.13) E 0.390 (9.91) 0.005 (0.13) 0.430 (10.92) E E1 0.330 (8.39) 0.380 (9.65) E1 0.005 (0.13) 0.600 (15.24) 0.670 (17.02) 0.290 (7.37) .330 (8.38) 0.485 (12.32) 0.580 (14.73) 0.246 (6.25) 0.254 (6.45) 0.005 (0.13) 0.600 (15.24) 0.670 (17.02) 0.600 (15.24) 0.670 (17.02) 0.485 (12.32) 0.580 (14.73) 0.485 (12.32) 0.580 (14.73) e 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) eA 0.400 BSC (10.16) 0.600 BSC (15.24) 0.600 BSC (15.24) 0.600 BSC (15.24) eA 0.300 BSC (7.62) eB L α 0.430 (10.92) 0.115 (2.93) 0.160 (4.06) 0.115 (2.93) 0.200 (5.08) 15° Shaded areas for 300 Mil Body Width 24 PDIP only 15° 0.115 (2.93) 0.200 (5.08) 15° 0.115 (2.93) 0.200 (5.08) 15° http://www.mitelsemi.com World Headquarters - Canada Tel: +1 (613) 592 2122 Fax: +1 (613) 592 6909 North America Tel: +1 (770) 486 0194 Fax: +1 (770) 631 8213 Asia/Pacific Tel: +65 333 6193 Fax: +65 333 6192 Europe, Middle East, and Africa (EMEA) Tel: +44 (0) 1793 518528 Fax: +44 (0) 1793 518581 Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or other intellectual property rights owned by Mitel. This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s conditions of sale which are available on request. M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation Mitel Semiconductor is an ISO 9001 Registered Company Copyright 1999 MITEL Corporation All Rights Reserved Printed in CANADA TECHNICAL DOCUMENTATION - NOT FOR RESALE