PRELIMINARY DATA SHEET NEC's HIGH NOISE REDUCTION HIGH SPEED ANALOG OUTPUT 5 PIN SOP OPTOCOUPLER PS8101 FEATURES DESCRIPTION • HIGH COMMON MODE TRANSISENT IMMUNITY: CMH,CML: ±10 kV/µs MIN NEC's PS8101 is an optically coupled isolator containing a GaAIAs LED on the light emitting diode (input) side and a PIN photodiode and a high speed amplifier transistor on the output side on one chip. Its small package makes it ideal for high density circuits and applications. • HIGH ISOLATION VOLTAGE: BV: 2500 Vr.m.s. • HIGH SUPPLY VOLTAGE: VCC = 35 V • HIGH SPEED RESPONSE: tPHL = 0.8 µs MAX, tPLH = 1.2 µs MAX • AVAILABLE IN TAPE AND REEL: PS8101-F3, F4 APPLICATIONS • COMPUTERS AND PERIPHERALS MANUFACTURES • GENERAL PURPOSE INVERTER • POWER SUPPLIES • RELAY AND PULSE TRANSFORMER REPLACEMENTS ESD SENSITIVE ELECTRICAL CHARACTERISTICS (TA = 25°C) PART NUMBER Diode SYMBOLS Detector UNITS VF Forward Voltage, IF = 16 mA V IR Reverse Current, VR = 3 V µA ∆VF/∆T TYP MAX 1.7 2.2 10 mV/°C -1.6 pF 60 IOH(1) High Level Output Current IF = 0 mA, VCC = VO = 5.5 V nA 3 IOH(2) High Level Output Current IF = 0 mA, VCC = VO = 30 V µA VOL Low Level Output Voltage IF = 16 mA, VCC = 4.5 V, LO = 1.2 mA V 0.1 ICCL Low Level Supply Current IF = 16 mA, VO = Open, VCC = 30 V µA 50 ICCH High Level Supply Current IF = 0 mA, VO = Open, VCC = 30 V µA 0.01 2 CTR Current Transfer Ratio, IF= 16 mA, VCC = 4.5 V, VO = 0.4 V % 20 35 RI-O Forward Voltage Temp. Coefficient, IF = 16 mA MIN Terminal Capacitance, V = 0 V, f = 1.0 MHz Ct 500 100 15 0.4 11 Isolation Resistance, V IN-OUT = 1k VDC, RH = 40 to 60 % Isolation Capacitance, V = 0, f = 1.0 MHz Ω pF tPHL Propagation Delay Time, (High → Low)1 IF = 16 mA, VCC = 5 V, RL = 2.2 k Ω, CL = 15 pF µs 0.5 0.8 tPLH Propagation Delay Time, (Low → High)1 IF= 16 mA, VCC = 5 V, RL = 2.2 k Ω, CL = 15 pF µs 0.6 1.2 CMH Common Mode Transient Immunity at High Level Output2 IF= 0 mA, VCC = 5 V, RL = 4.1 k Ω, VCM = 1.5 kV kV/µs 10 CML Common Mode Transient Immunity at Low Level Output 2 IF= 16 mA, VCC = 5 V, RL = 4.1 k Ω, VCM = 1.5 kV kV/µs -10 CI-O Coupled PARAMETERS PS8101 10 0.4 NOTES: 1. CTR rank K: 20 to 35 (%) N: 10 to 35 (%) CON'T ON NEXT PAGE. California Eastern Laboratories PS8101 ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS Diode IF VR PD Detector VCC VO IO PC Coupled BV TA TSTG PARAMETERS UNITS RATING Forward Current Reverse Voltage Power Dissipation mA V mW 25 5.0 45 Supply Voltage Output Voltage Output Current Power Dissipation V V mA mW 35 35 8.0 100 Vr.m.s. °C °C 2500 -55 to +100 -55 to +125 ORDERING INFORMATION PART NUMBER PACKAGE PS8101 Isolation Voltage2 Operating Ambient Temp. Storage Temperature 5-pin SOP PS8101-F3 PACKAGE STYLE APPLIICATION PART NUMBER* Magazine case 100 PCS PS8101 Embossed Tape 2500 pcs/reel PS8101-F4 * For the application of the Safety Standard, following part number should be used. Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. AC voltage for one minute at TA = 25°C, RH = 60% between input and output. (Continued from previous page) NOTES: 2. Test Circuit for Propagation Delay Time: 0.1 µF (Pulse width = 100 µs Duty Cycle = 1/10) Input (monitor) Input VCC = 5 V Pulse input (IF) 50% RL = 2.2 kΩ VO (monitor) CL = 15 pF 5V Output 47 Ω 1.5 V tPHL VOL tPLH *CL is approximately 15 pF which includes probe and stray wiring capacitance. 3. Test Circuit forCommon Mode Transient Immunity: 1.5 kV VCM 90 % VCC = 5 V IF 0.1 µF 10 % RL = 4.1 kΩ 0V VO (monitor) tr tf V0 (IF = 0 mA) 5V 2V VCM 0.8 V V0 Usage Cautions: (IF = 16 mA) 1. When handling this product, precautions should be taken against static electricity. 2. A by-pass capacitor of ≥ 0.1 µF is used between VCC and GND. V0L PS8101 MARKING OUTLINE DIMENSIONS (Units in mm) PS8101 3.4 +0.3 -0.1 (Top View) 5 4 3 1. 2. 3. 4. 5. 1 8101 N234 No. 1 pin Mark Initial of NEC (Engraved mark) Assembly Lot N N 2 7.0±0.3 4.4 2 34 Week Assembled Year Assembled (Last 1 Digit) Rank Code 0.1 ±0.1 0.15 +0.10 -0.05 2.6 ±0.2 Anode Cathode GND VO VCC 1.27 0.4 +0.10 -0.05 0.5±0.3 0.25 M Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. 12/22/2004 A Business Partner of NEC Compound Semiconductor Devices, Ltd.