POWER-ONE HLD15YGB

HLD SERIES - 60 WATT
Half-Brick
DESCRIPTION
The HLD series are through-hole mount, Half-brick, Low profile,
Dual output DC/DC high density converters. The HLD series
provides onboard conversion of telecom and datacom input
voltages to isolated low output voltages without the need for a
heatsink. The HLD series is well suited for distributed power
architectures, telecom equipment, and LAN/WAN and data
process applications.
FEATURES
TECHNICAL SPECIFICATIONS
Input
Parameter
Voltage Range
24 nom.
48 nom.
Transient Voltage Withstand
24 nom.
48 nom.
Turn-on Time
Maximum
Unit
18-36
36-72
VDC
50/100
100/100
20
Input Reflected Ripple Current
80
• Single-board, multi-layer
design
• Planar magnetics
• Fully automated - minimal
‘touch time’
• Two independently
regulated outputs
• Can start into high
capacitive load
• Low profile
• Standard half-brick size and
pinout
General
V/ms
Parameter
Maximum
Unit
300
KHz
Positive
On>3.5/Off<1.8
V
Negative (optional)
On<1.8/Off>3.5
V
Isolation Input-Output
1500
VDC
Temp. Coefficient
0.03
%/ C
mS
Switching Frequency
mApk-pk
Remote ON/OFF
Vin UVLO Window
24 nom.
48 nom.
17/15
34/30
Von/Voff
Output
Parameter
Setpoint Accuracy
Line Reg. Vin min. – Vin max., Iout
rated
Output 1
Output 2
Load Reg. Iout min. – Iout max., Vin
nom.
Output 1
Output 2
Min. Output Current, each Output
Maximum
Unit
±1
% Vout
0.2
1.0
Operating Range
-40 to +100
°
Storage Range
-40 to +125
°
105-115
°
Thermal Shutdown Range
% Vout
Humidity max, Non-Condensing
Safety
0.5
1.0
% Vout
1.0
A
Pk Deviation
4
% Vout
Settling Time
500
µS
±10
%
Power Limit Threshold Range
110-150
% Pout rated
OVP Trip Range
115-140
% Vout
95
2
90%
Efficiency
80%
70%
Vin = 36V
60%
Vin = 48V
Vin = 72V
50%
Notes
40%
Specifications typically at 25°C, nominal line, and full load unless
otherwise stated.
Iout1 / Iout2 (A)
Specifications subject to change without notice.
Patents Pending
REV. 08/01
1
C
C
C
%
Pending
Weight (approx)
Dynamic Reg., 25% Loadstep
Voltage Trim Range
°
Board Temp
HLD15ZED
Oz.
HLD SERIES - 60 WATT
Half-Brick
MODELS - (See the last page of section for options.)
MODEL
HLD15YGE
HLD15YGB
HLD15YED
HLD15YEB
HLD15ZGE
HLD15ZGB
HLD15ZED
HLD15ZEB
HLD15ZED-G****
NOTES:
*
**
***
****
INPUT VOLTAGE
(VOLTS)
INPUT VOLTAGE
RANGE (VOLTS)
MAXIMUM INPUT
CURRENT (AMPS)*
OUTPUT
VOLTAGE (VOLTS)
RATED OUTPUT
CURRENT (AMPS)***
24
24
24
24
48
48
48
48
48
18-36
18-36
18-36
18-36
36-72
36-72
36-72
36-72
36-72
4.4
4.4
4.5
4.5
2.3
2.4
2.4
2.4
2.4
5.0/3.3
5.0/1.8
3.3/2.5
3.3/1.8
5.0/3.3
5.0/1.8
3.3/2.5
3.3/1.8
3.3/2.5
12/15
12/15
15/15
15/15
12/15
12/15
15/15
15/15
15/15
RIPPLE & NOISE
pk-pk (mV)
100/100
100/100
100/100
100/100
100/100
100/100
100/100
100/100
100/100
Maximum input current at minimum input voltage, maximum rated output power.
At nominal Vin, rated output.
Current can be drawn from any single output to its maximum rated value, or from both outputs to a combined power level of 60W.
-G overcurrent protection is latched; all other models hiccup.
MECHANICAL DRAWING
2.28
(57.9)
1.40 (35.56)
1
1.00 (25.40)
2
0.40 (10.16)
3
0
4
BottomView
5
1.50 (38.10)
6
1.20 (30.48)
7
0.90 (22.86)
8
0.50 (12.70)
9
0.20 (5.08)
10
0.10 (2.54)
2.40
(61.0)
0.40
(1.02)
1.90 (48.26)
0
0.19 (4.80)
0.50 (12.7)
0.18
(4.60)
0.50
(12.70)
Units inches (mm)
PIN
Tolerances
Function
1
-Vin
2
No Pin
3
Shutdown
4
+Vin
5
+Vout2
6
Vout2RTN
7
Vout2 Trim
8
+Vout1
9
Vout1RTN
10
Vout1Trim
Inches:
.XX ± 0.020
.XXX ± 0.010
Pin:
± 0.002
(Millimeters)
.X ± 0.5
.XX ± 0.25
± 0.05
(Dimensions as listed unless
otherwise specified.)
2
TYPICAL
EFFICIENCY**
84%
83%
81%
81%
86%
85%
83%
83%
83%
OPTIONS
When ordering equipment options, use the following suffix information. Select the option(s) that you prefer
and add them to the model number. Example ordering options are located below the options table.
OPTION
SUFFIX
APPLICABLE SERIES
Negative Logic
N
HAS, HBD, HBS, HES, HLS, HLD, LES,
QBS, QES, QLS, TES, TQD
Lucent-Compatible
T
HAS, HBD, HBS, HES, HLS, QBS, QES,
QLS
Terminal Strip
TS
XWS, XWD, XWT
Trim
1
IAS, LES
Enable
2
IAD, IAS, LES, SMS
Trim and Enable
3
IAS, LES
Current Share
4
SMS
Headerless
Y
Encapsulated EWS, IWS, OWS
Pin Length and Heatsink Options
REMARKS
TTL "Low" Turns Module ON
TTL "High" Turns Module OFF
Standard Pin Length is 0.180" (4.6mm)
0.110" (2.8mm) Pin Length
8
All Units (Except SMS)
0.150" (3.8mm) Pin Length
9
All Units (Except SMS)
0.24" (6.1mm) Horizontal Heatsink
1H
All Units (All Units Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.24" (6.1mm) Vertical Heatsink
1V
All Units (All Units Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.45" (11.4mm) Horizontal Heatsink
2H
All Units (All Units Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.45" (11.4mm) Vertical Heatsink
2V
All Units (All Units Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.95" (24.1mm) Horizontal Heatsink
3H
All Units (All Units Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
0.95" (24.1mm) Vertical Heatsink
3V
All Units (All Units Except DIP, HLS, HLD, QLS,
SIP, SM, TLD, and TKD Packages)
Includes Thermal Pad
Example Options:
HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95” vertical heatsink.
LES015YJ-3N = LES015YJ with optional trim and enable, negative logic.
QBS066ZG-AT8 = QBS066ZG-A with Lucent-compatible trim and 0.110” pin length.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
3