(888) IPD-CONVerters ● (888) 473-2668 ● www.ipdconverters.com FRD SERIES - DUAL OUTPUT, 5 WATT DESCRIPTION FEATURES • 500V Isolation • Short Circuit Protection • 6-Sided Shielding FRD dual output DC/DC converters offer excellent • Wide Input Range regulation and isolation in an industry standard • Trim and Enable Pins package. Available in several input versions, the FRD • Remote Sense Pins is perfect for industrial, datacom, or telecom applications. The FRD features short circuit protection, six-sided shielding, and 500 VDC isolation. Please see the FRS series for single output applications. Efficiency vs. Load (28V Input) 80 75 EFFICIENCY % 70 65 60 55 EFF. FRD2812 50 EFF. FRD2815) 45 40 35 10 20 30 40 TECHNICAL SPECIFICATIONS 50 60 70 80 90 10 LOAD % Input Voltage Range Reflected Ripple Reverse Input Current 5V, 12V, 24V, 28V, and 48V Nominal See selection chart for specific input range. 20% Iin Max. 100% Iin Max. Efficiency vs. Load (48V Input) 70 65 EFFICIENCY % 60 Output Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Minimum Output Current Short Circuit Protection1 ±1% Vout ±0.15% Vout 55 50 45 EFF. FRD4812 40 EFF. FRD4815 ±0.15% Vout Iout Rated 10 % lout Rated Continuous 35 30 25 10 20 30 40 50 60 70 80 90 10 LOAD % General Switching Frequency Isolation Input - Output Isolation Resistance - Input to Output Case Temperature Operating Range Storage Range Humidity Max, Non-Condensing Temperature Coefficient Vibration, 3 Axes, 5 Min Each Safety Weight (Approx.) 20 kHz 500 VDC 109 Ohms -25 To +85°C -40 To +125°C 95% ±0.02%/°C 5 g, 10 - 55 Hz Consult Factory 2.2 oz C-64 Notes † MTBF predictions may vary slightly from model to model. Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. FRD SERIES - DUAL OUTPUT, 5 WATT MODELS - (See the last page of this file for options.) Vin (Volts) Vin Range (Volts) Iin Max.* (Amps) Vout (Volts) Iout Rated (Amps) Ripple & Noise Pk-Pk (mV) Efficiency Typ. ** Model 5 5 12 12 24 24 28 28 48 48 4.65 - 5.50 4.65 - 5.50 10.90 - 13.20 10.90 - 13.20 21.60 - 26.40 21.60 - 26.40 25.20 - 30.80 25.20 - 30.80 43.20 - 52.80 43.20 - 52.80 2.01 2.04 0.85 0.86 0.43 0.45 0.37 0.38 0.21 0.22 ±12 ±15 ±12 ±15 ±12 ±15 ±12 ±15 ±12 ±15 ±0.23 ±0.19 ±0.23 ±0.19 ±0.23 ±0.19 ±0.23 ±0.19 ±0.23 ±0.19 40 40 40 40 40 40 40 40 40 40 65% 66% 66% 67% 66% 65% 69% 71% 65% 66% FRD512 FRD515 FRD1212 FRD1215 FRD2412 FRD2415 FRD2812 FRD2815 FRD4812 FRD4815 * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. MECHANICAL DRAWING 2.00" (50.8mm) 0.18"(4.6mm) MIN. 0.100" -0.300" (-7.6mm) (2.5mm) 0.500" (12.7mm) 1.40" (35.6mm) 0.800" (20.3mm) 3 4 5 2.00" (50.8mm) BOTTOM VIEW 1 2 0 DIA 0.040" (1.0mm) 0.40" 0 (10.2mm) 1.10" (27.9mm) 0.200" (5.1mm) Pin Thermal Impedance Natural convection 100 LFM 200 LFM 300 LFM 400 LFM 10.3 7.7 6.3 5.1 4.1 °C/W °C/W °C/W °C/W °C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. Tolerances Function 1 2 3 4 5 +Vin -Vin + Vout Common - Vout Inches: .XX ± 0.040 .XXX ± 0.010 (Millimeters) .X ± 1.0 .XX ± 0.25 Pin: ± 0.002 ± 0.05 Case: + 0.04, - 0.00 + 1.0, - 0.0 (Tolerances as listed unless otherwise specified.) C-65 OPTIONS When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table. OPTION SUFFIX APPLICABLE SERIES Negative Logic N HAS, HBD, HBS, HES, LES, QBS, QES, TES, TQD Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES Terminal Strip TS REMARKS TTL “Low” Turns Module ON TTL “High” Turns Module OFF XWS, XWD, XWT Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES Current Share 4 SMS Headerless Y Encapsulated EWS, IWS, OWS PIN LENGTH AND HEATSINK OPTIONS Standard Pin Length is 0.180” (4.6mm) 0.110” (2.8mm) Pin Length 8 All Units (Except SMS) 0.150” (3.8mm) Pin Length 9 All Units (Except SMS) 0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Horizontal Heatsink 2H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Horizontal Heatsink 3H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and 0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length. NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. C105