#’
-SHARP
SPECIFICATIONS
Product Type : l’7%FG
Yodel
No.
lens-integrated
CMOSColor Area Sensor for CIF
LZOP3820
%This specifications
contains 24 pages including the cover.
If you have any objections,please
contact us before issuing
purchasing
CUSTOMERSAcCEpTANCJ3
DATE:
BY:
PRESENTED
I Dept. General Manager
REVIEWD BY:
PREPAREDBY:
Product Development Dept. II
CCD Development Center
Integrated Circuits Devel
SBABP CORPORATION
order.
SHARP
LZOP3820
l Handle this document carefully
for it contains material protected by international
copyright law. Any reproduction,
full or in part, of this material is prohibited
without the express written permission of the company.
l Vhen using the products covered herein,
please observe the conditions written herein
and the precautions outlined in the following paragraphs. In no event shall the
company be liable for any damages resulting
from failure to strictly
adhere to these
conditions and precautions,
(1) The products covered herein are designed and manufactured for the following
application
areas. Vhen using the products covered herein for the equipment
listed in Paragraph (2>, even for the following application
areas, be sure
to observe the precautions given in Paragraph CU. Never use the products
for the equipment listed in Paragraph (3).
*Office electronics
OInstrumentation
and measuring equipment
#Machine tools
SAudiovisual equipment
*Home appliances
Xommunication equipment other than for trunk lines
(2) Those contemplating
using the products covered herein for the following
equipment which demands high reliability,
should first contact a sales
representative
of the company and then accept responsibility
for incorporating
into the design fail-safe
operation, redundancy, and other appropriate
measures for ensuring reliability
and safety of the equipment and the overall
system.
*Control and safety devices for airplanes, trains, automobiles, and other
transportation
equipment
*Mainframe computers
*Traffic control systems
*Gas leak detectors and automatic cutoff devices
,Bescue and security equipment
*Other safety devices and safety equipment,etc.
(3) Do not use the products covered herein for the following equipment which
demands extremely high performance in terms of functionality,
reliability,
accuracy.
-Aerospace equipment
Xcfnmunications equipment for trunk lines
Control equipment for the nucJear power industry
BMedical equipment related to life support, etc.
(4) Please direct all queries and comments regarding
above three Paragraphs to a sales representative
0 Please direct
representative
all queries regarding
of the company.
the interpretation
of the company.
the products covered herein
to a sales
of the
or
SHARP
1
LZOP3820
CONTENTS
.
1. GENERALDESCRIPTION ~,I,*o.I.,Ill.l,.II,,.II1II1*1.L,~I~
P. 2
2. ARRANGEMENT
OF PIXELS ANDCOLORFILTORS 1**.111,*111.1,0
P. 3
3. BLOCKDIAGRAM ,..1,1,.111.1...,1...*.1...1.1,.,.,...**.*.
P. 4
4. PIN CONFIGURATION I.,,,I,..I...I..II.,.1O,IIOI..1,111..
P. 5
5. PIN DESCRIPTION ll,lI1111,1,1111,,,11,,11,1111,1.0,1~111
P. 6
6. ELECTRIC CHARACTERISTICS~II.,,,.I,,.11.1..,,I.,,.L,,III,,
P. 7
7. IMAGINGCiiABACTERISTICS II.I......11,1,,I.,,,,.I..I..I,.I
P.a
8. LENS SPECIFICATIONS ..,.11...1.1,,1.1,,..1....,.1..1..1..
p. 9
9. TIMING DIAGRAM ,,1,,,,1111.11111,,1,1~1,11~..~,..~~I1~..1
P. IO
10.
DESCRIPTIONOF SERIAL DATA 11111,1,,..1111.1111.011111,1
P. 13
1 1. EXAMPLEOF STANDARD
OPERATINGCIRCUIT ,.*..'.ll,,,*,l,ltl.
P. 16
SPECIFICATION FORBLEMISH . . . . ..*..0..111,.1.10,11..1..
P. 17
12.
1 3. CAUTIONSFORUSE ,1,,1.1,11..10,,,1....‘.,,~......,.~...
14.
PACKAGEOUTLINE ANDPACKINGSPECIFICATI(JN Illl,,l#ll.~l*t
P. 18
P. 20
SHARF,
l.GENERAL
LZOP3820
2
DESCRIPTION
LZOP3820 is a l/7-type(approx.2.6mm)
The sensor further
includes
a timing
sampling(CDS)
circuit,
an auto gain
digital
converter(ADC)
circuit.
All
by 3.3V single power supply. Having
possible
to make ultra-small
color
lens-integrated
CMOS image sensor.
generatoer(TG),
a correlated
double
control(AGC)
circuit
and an analog-tothe circuits
of the sensor can be driven
smaI1 lens and small LCC-type flat pakage,
camera easily.
Features
1) Number of image pixels
2)
3)
4)
5)
6)
7)
8)
9)
10)
: Horizontal
367 x vertical
291
(approximately
110,000 pixels)
: Horizontal
5.6Pm x vertical
5.6pm
Square pixel,
Pixel pitch
Progressive
acan
Compatible
with CIF standard
Primary color filter
composed of B. G, B
AnaIog output and a-bit digital
output
Variable
electronic
shutter (l/30 to l/10,000
s>
Variable
gain control
(3 to 30 dB)
Can be operating
by DC3.3V single power supply
36-pin half-pitch
LCC-type small pakage
(Base section size: ll.5mmXll.
5mm max. )
11) pprox. 58” (degrees) of horizontal
view angle lens includes.
12) Not designed or rated as radiation
hardened
Applications
Yireless
phone camera
Image capture camera for PC,PDA
Amusement (Game, Toy)
etc.
.
#The circuit
diagram and others included
in this specification
are intended
for use
we take no responsibility
for
to explain
typical
application
examples. Therefore,
any problem as may occur due to the use of the included circuit
and for any problem
with industrial
proprietary
rights or other rights.
SHARP
LZOP3820
2. -T
3
.OF PIXELS AND COLOR FILTERS
Optical
black
(4 Pixels)
Optical
black
(13 Pixels)
367(H)
x 291(V)
Optical
black
(13 Pixels)
by
opticaliy
OB(B):Standard
Optical
black
(4 Pixels)
(1
,
. . ..-
1
R
(367.291)
lG IRI
.
(367.1)
shielded
signs1
pixels
genera-
CLK tDATA-
HD,VD-
3
V
TG
output
.
I
+
+
I
Control
AGC
+
AGC
D/A
8bit
V
>
8bit
A/D
Digital
-+ Video
output
:*
-’ SHARP
4.PIN
LZOP3820
CONFIGRATION
VIEW>
BIAS1
SCLK
N. c.
CLP
D5
OFS
D4
BIAS2
LZOP3820
D3
SICOUT
D2
SIGIN
Dl
ACND
DO
AVDD
DGMD
N. c.
DVDD
*a
SHARP
a
5.
PIN
LZOP3820
DESCRIPTION
STBY
Ir;
N. C.
DVDD
DGND
DO
Dl
ii
13
14
16
18
19
I
1
I
I
1
D5
Output
-
Digital
Digital
Digital
Digital
n1 -~:L-,
mgisal
Digital
-- ~~
Digital
Digital
Diiital
1 AIX s&al
output 5
1 No connection
I ADC signal output 6
Digital power SUDDEN
ADCsigna 1 OUtDUt
_ 7 (MSB)
l--d------- CIWK
-1--1. ouepu~
-__A.-__A
/n
rxlR,-\
I nererence
\Y. urhuu/
1 Digital mound
Horizontal drive pulse input
I Vertical drive Dulse inmt
I Control data input (AGCiEE,Offset etc. >
II No connection
-~-~~-~ -1 Control clock input for SD1
Analog bias voltage for clamp circuit
Offset bias voltage for AGC
Analog bias voltage 2 for image sensor
Analog image signal output
-Analog image signal input
Analog ground
Analog power supply
No connection
I
N. C.
DGND
27
I
I
1
VD
iDI
28
1
SCLK
CLP
._
N. c.
rs
1
I
3
HD
1
Digital power supply
Digital ground
ADC signal output 0 (L SB)
AJX si&l
output 1
ADC simal OutDut 2
1 AM: signal
1
34
35
36
1
1
1
1
,1
Digital
Digital
23
t=k-
Digital
Di.gital
Digital
Digital
Digital
output
output
1
I++-33
II
I
D4
zg
29
OutDut
outp,t
output
D3
D6
DVDD
D7
-7 ”
LLh
20
21
sl.7
1
I
D2
15
17
6
BIAS2
SIGOUT
SIGIN
AGND
AVDD
N. C.
I
I!
1
1I
Input
1I
hlDUt
I
I
Input
I
1
outDut
output
n ‘ .I
uuqlur
-
Input
-
I
1
I
-
Digital
Analog
Analog
,I ADC siml
output
output 4
I
1
I
1
J
LZOP3820
SHARP
6.ELECTRIC
7
CHARACTERISTICS
6 - 1. ABSOLUTEMAXIMUM BATINGS
Parameter
Power supply voltage
Input signal voltage
Storage temperature
S)TllbOi
VDD
V@
Tstr
Wings
-0.3
-0.3
-
4.6
-
VDD+O.
-20
-70
Unit
V
V
3
@c
6 - 2. BECOBBNDEDOPEBATING CONDITIONS
Parameter
Power supply voltage
Oneratine temnerature
Oscillator
frequency
Digital
input Low level
vo 1tage
High level
Analog input voltage
or---
---..a
--c-m
~~~
Analog bias voltage
Note 1 : Apply
Note 2 : Apply
Note 3 : Apply
Please
to input
to input
to pins
do not
SYUlbOl
VDD
Tonr
Fck
V9L
VdJH
.
YIN
‘lYP
MAX
Unit
3. 0
3.3
-10
25
9-o
3. 6
60
V
"c
__
Note
MHZ
0.2VDD V
0.8VDD
VDD
(Connect to terminal
through capacitor)
(Connect to GND
through capacitor)
1
V
pins HD, VD, SD1 and SCLK
pin SIGIN, Please do not connect to DC directly.
BIASI, BIASZ, OFS, ADL, DAL, CLP.
connect to GND directly.
2
3
C’
SHARi=
~5
LZOP3820
8
7. 7
Readout mode : l/30 see, Normal mode
Ambient temperature : 25 “C
Driving voltage : 3.3 V
Color temperature of light source : 3200K
*Measurement point : Analog image signal output (pin no.32) before ACC and AD.
I
[Note]'
(a> Vo is the average output voltage of Green channel int the central areaWlO,V/lO)
under
uniform illumination.
The standard exposure condition is defined when Vo is 150 mV.
(b) The image area is divided into IO x 10 segments under 10 times exposure of the standard
exposure condition,
The segment’s voltage is the average output voltages of all pixels
whithin the segments. Vsat is the minimum segment’s voltage of all the segments voltage.
cc> Vdark is the difference between average output voltage of the effective area and that of
the OB area, under non-exposure condition.
Cd). Image area is divided into 10 X 10 segments under non-exposure condition.
DSNU is defined
by (Vdmax - Vdmin), where Vdmax and Vdmin are the maximum and minimun values of all
the segments voltage, respectively.
-(e> R(G) is the average output voltage of Green channel at central areaWlO.V/lO)
when a
1000 Iux light source on a 90% reflector
is image.
(f) One mean horizontal
line signal <bi> is obtained by adding all the horizontal
line
signals <aij> verticalIy
and dividing them by the line number, <xi> is the deviation of
the center pixel from the average of successive 5 pixels in <bi>. V-FPN is the maximum
absolute value of (xi>.
(g)The limited
resolusion
in the central area(H/lO,V/lO)
whitch the image of TV resolusion
chart(ex.
EIAJ test chart:type-A)
can be distinguished
on the B/I video monitor when
converted into composite video signal.
(h)The limited
resolusion
in the perpheral area(image height:Y=O.7)
under the conditions
mentioned above.
tilDefined
following
formura at the brightness of standard output voltage. Cat C-channel]
Vco:output voltage of edge of the image. (image height:Y=O. 8)
0ko/Vce)X100C%l
Vce:output voltage of center of the image.
(j)Difference
of center between image and monitor, Ratio of horizontal
underscaning
monitor size.
(k) IVDD is the total current of analog and digital
power supply in the dark and on the
standard load condition.
SHARP
8.
LENS
LZOP3820
SPECIFICATIONS
Kondi t ions1
(a> Effective
Image Area : (Hj2.06
(b) TV distortion
at capturing
is defined
rectangular
x (V)l. 63mm
the formura,
pattern
(A y /Y
> x 1 0 0 [%I
sized Horizontal
by Vertcal as 4by 3.
“Y”
is defined as the Vertical
height
of center of Horizontal
* y”
is defined as the Vertical
height
of edge of Horizontal
line.
line.
t
(c) The range isthe best points
by adjustment
(d) Toruques which are necessary for turning
(at shipping
of products)
.
by screwing the lens head.
the lens.
Mirror
nor*a1
11rror
*The falling
*The rising
(DO-D7)
ADOUT
CLK
HD
(DO-D7 >
HD
2
4
8
12
I8
20
24
104
108
112
116
edge of HD pulse
124
128
132
138
140
32
144
36
must be between two rising
must be between two rising
120
28
9 - 1. Ho;izontal
%Ixxxxxm
1 08 .-.-.-.-.--..................OB
s
3
di
edge of HD pulse
7
906
L
Qld
: I*
.. ..
152
44
156
48
158
60
172
64
176
68
180
72
08
184
7’6
x x x x x K x x x x x x x
()B . . . . . . . . . . . . . _ ._...
_ . . . . . . .._ 08
KxXXXxxxrxwxxxxwxxxKxxX
164
56
,)B ._......._._._...............
160
52
Timing
edges of CLK(90)
and CLK(91).
edges of CLKtO> and CLK(l).
148
40
Pulse
x x
366
2
188
80
K x
364
4
192
84
x x
362.
6
196
200
10
x n-T
360
358
8
88 ioie2
.. .
,I
.>.!
,.
’
SHARP
LZOP3820
11
SHARP
,
LZOP3820
12
SHARP
10.
LZOP3820
DESCRIPTION
OF
SERIAL
(Fix
13
DATA
to Low level)
Shutter speed control
(Exposure time is 1 to l/330
D31
D32
D33
D34
D35
D36
D37
D38
MIRH
MIRV
SAD1
(MS31
SAD0
(LSB)
MAX2
(MSB)
MAX 1
MAX0
(LSB)
L PMD
frame period)
H:Horizontal
mirror inversion
image,
H:Vertical
mirror inversion
image,
Phase select of AD clock
(Fix to Low level)
Fixed gain select
(3 to 10 dB)
L:Normal
L:Normal
A:Power save mode (AGC and AD off),
L:All
image
image
active
SHARI=
10-l.
LZOP3820
SETTING
OF
AUTUN
14
CONTROL
*One LSB of the gain code represents
appoximately
0.156dB.
*Nominal
gain values at typical
codes are shown below.
1
20
H(HI
10-2.
SETTtNG
OF
oFFSET
LEVEL
-One LSB of the offset code represents
appoximately
0.002Y.
-Nominal
offset
values at typical
codes are shown below.
HI
RI
H]
SHARP
LZOP3820
-One LSB of shutter
10-4.
,SETTING
*One LSB of gain
speed code represents
OF
FIXED
code represents
GAIN
1dB.
15
lfi,
where 1H is HD pulse
period.
SHARF,
LZOP3820
ll.EXAMPLE
I
1
OF
OPERATING
16
CIRCU
I
A
3
w
,*
.’
SHARP
LZOP3820
12.SPECIFI&A-JION
FOR
17
BLEMISH
<To
be J&rmdb
1) Definition
of blemish
*Size of blemish : d 3 lines square by vertical lines.
[For reference]
Size of stain : 2 4 lines square by vertical
l
lines.
(Green channel : 150mV)
$@efer to note below
White blemish
{note)
B
l
l
vout
l
Vstd
:Blemish level defined in fig. below.
: Average output voltage at Green channel.
: 150 mV. The standard output voltage defined
* 7. Imaging Characteristics
”
2) Measureing conditions
Operating temperature
* Operating voltage
Measureing point
l
l
: Topr = 25°C
: VDD = 3.3V
: Analog image signal
White
Black
in the specification
output(Pin
No.32) before AGC and AD.
blemish
blemish
White
(a)
(Yout
= 150mV at Green
fig.
blemish
(b) Non-exposed
Exposed
channel)
Definition
of blemish
of
level
SHARP
13.
LZOP3820
LAUTIONS
FOR
18
USE&
1, Package breakage
In order to prevent the package, the lens holder and lens from being’broken,
instructions
below:
follow the
1) This CMOS image sensor is a precise optical component and the packaege-base material
is ceramic. Therefore, please be careful about the following instructions.
Take care not to drop the device when mounting. handling, or transporting.
Avoid giving a shock to the package. Especially when Ieads are fixed to the
shocks or the circuit board, a small shock could break the package more
easily tban when the package isn’t fixed.
l
l
2) If any damage or breakage occur on the surface of the lens, its characteristics
could deteriorate.
Therefore.
l Do not hit the Lens.
-Do not give a shock large enough to cause distortion,
*Do not scrub or scratch surface of the lens.
--Even a soft cloth or applicator,
if dry, could cause dust to scratch the Lens.
2. Electrostatic
Darnage
. As compared with general MOS-LSI, CMOS image sensor has lower ESD.
Therefore, take the following anti-static
measures when handling the CHCS image sensor.
1) Always discharge static electricity
by grounding the human body and the instrument
to be used. To ground the human body, provide resistance of about 1MQ between the
hman body and the ground to be on the safe side.
2) When directly
handling the device with the fingers, hoId the lens holder and do not
touth the lead,
3 > To avoid generating static electricity,
a. do not scrub the body and lens surface with cloth etc.
b. do not attach any tape or labels.
4) Vhen storing or transporting
the device, put it in a container of conductive
material.
..
SHARI==
LZOP3820
19
3. Dust and contamination
Dust or contamination
on the surface of lens and the inside of the lens holder could
deteriorate
the output characteristic
or cause a scar. In order to mini&e
dust or
contamination
on the device, take the following precautions:
1 > Do not remove the lens from the body.
Especially when adjusting macro, be careful
counterclockwise
too much
not to remove the lens by turning
it
2) Do not touch the surface of the lens with the fingers. If dust or contamination gets
on the surface of the lens, the following cleaning method is recommended:
l IInadle the built-in
lens CMOSimage sensor in a clean environment such as a
cleaned both.
.(The cleanliness
level should be, if possible, if possible class 1000 at least. >
*Dust from static electricity
should be blown off with an ionized air blower.
For anti-electrostatic
measures, however, ground all the leads on the device
before blowing off the dust.
=The contamination
on the surface of the lens should be wiped off with a clean
applicator
soaked in isopropyl alcohol. Wipe slowly and gently in one direction
only.
--Frequently replace the applicator and do not use the same applicator
to
clean more than one device.
Make sure there is no dust or contamination on the lens and screw it on the
lens holder.
l
4. Other
1) Soldering measure and condition.
*Use ESD-measured soldering iron.
*Do not put too much force onto the lens and the lens holder while soldering.
Be careful not to let the soldering iron touch the lens holder.
--Soldering can be quickly/neatly
done by laying the soldering iron so it
lightly
touches the border between the package and the circuit board
and sliding it in sideways.
2) There is no guarantee of the performance of the device which haa been removed or
resoldered after being soldered once under the conditions mentioned above.
3 > Avoid using or storing the CMOS image sensor at high temperature or high humidity
as it is a precise optical component. Do not give a mechanical shock to the CMOS
i wage sensor.
4) Do not expose the device to strong light, For the color device, long exposure to
strong light will fade the color of the color filters.
l
SHARP
LZOP3820
1 4. PACKAGEOUTLINE AND PACKING SPECIFICATION J
1. Package Outline Specification
Refer to attached drawing
2. Markings
Marking contents
(1) Product name
(2>Companyname
(3)Countryname
(41Datecode
:
:
:
:
LZOP3820
SHARP
JAPAN
1
I-----
I
Denotes the production ref.code.(l--2figures)
Denotes the production day of the week
1
2
314
51617
SUN. MON. TUE. 1 WED. TIIU. 1 FRI. 1 SAT.
Denotes the production week
(01, ozo3,
,52,53)
Denotes the production year.
(Lower two digits of the year. >
l
l
l
l
Positions of markings are shown in the package outline drawing
But,ntarkings shown in theat drawing are not provided any measurements of their
and their positions.
charactuers
!. Packing Specification
3 - 1. Packing materials
Device tray
Cover tray
Rubber band
Buffer
Cushion bag
Tape
Label
1 Conductive plastic
(SUdevices/tray)
1 Conductive plastic(2trays/case)
Cardboard
Conductive
Paper
Paper
1 Device packing(Gays/case)
Device packing
Device tray fixing
Shock absorber of device tray
Device tray fixing
Sealing cushion bag and device case
Indicates part number,
auantitv and date of manufacture
3 - 2. External appearance of packing
Refer to attached drawing
.
. Precaution
1) Before unpacking, confirm the imports of the chapter ‘l&CAUTIONS FOE USE” in this
device specifications.
2) Unpacking should be done on the stand treated with anti-ESD. At that time, the same
anti-ED
treatment should be done to operater’s body, too.
NIE NUMBER (NOTE)
--_-__________-_-_
C-HS3820A
-.
SHARF,
LZOP3820
N
8
:
I
:
:
/
T
,
SHARP
LZOP3820
S
__
fH
a
d
T
c)
;i
w
0
i
B
0 ‘g -xoJddy
SHARP
LZOP3820
!is?iz
\\\ -----
-
t
(UNIT
:
mm)
t4mMAw
tt
+
yxIL(-T-~-oOUTIIwr
WrEGRATKJ CmJfrs (lc) GROW
SHARP
CORPORATION
External
FTMSH
8%
NAME
,3--F
a,,E
.
m
DRAWING
\ \i , I
Appearance
of
Packing
I
*.;:::::
i:::;;;: : .
::::
;:
: : : ; : : : 1 : : : : :
II.,
9..
; : : ;
=
No.
L;C:-:H’L’3’8i
* * *
@A’ * .’
J