L4916 VOLTAGE REGULATOR PLUS FILTER .. .. .. .. FIXED OUTPUT VOLTAGE 8.5 V 250 mA OUTPUT CURRENT HIGH RIPPLE REJECTION HIGH LOAD REGULATION HIGH LINE REGULATION SHORT CIRCUIT PROTECTION THERMAL SHUT DOWN WITH HYSTERESIS DUMP PROTECTION DESCRIPTION This circuit combinesboth a filter and a voltageregulator in order to provide a high ripple rejection over a wider input voltage range. A supervisor low-pass loop of the element prevents the outputtransistor from saturationat low input voltages. The non linear behaviour of this control circuitry allows a fast settling of the filter. POW ER MINIDIP (4 + 4) ORDERING NUMBER : L4916 BLOCK DIAGRAM June 2000 1/8 L4916 PIN CONNECTION (top view) ABSOLUTE MAXIMUM RATINGS Symbol Value Unit Vi Peak Input Voltage (300 ms) 40 V Vi DC Input Voltage 28 V IO Output Current Internally Limited Ptot Power Dissipation Internally Limited Tstg, Tj Parameter Storage and Junction Temperature – 40 to 150 °C Value 80 20 Unit THERMAL DATA Symbol Parameter R th j-amb Thermal Resistance Junction-ambient Rth j-pins Thermal Resistance Junction-pins 2/8 Max Max °C/W °C/W L4916 ELECTRICAL CHARACTERISTICS (Tamb =25 °C; Vi = 13.5 V, testcircuit of fig. 1, unlessotherwise specified) Symbol Parameter Vi Input Voltage VO Output Voltage Test Conditions Vi = 12 to 18 V IO = 5 to 150 mA Min. 8.1 Typ. Max. Unit 20 V 8.5 8.9 V 1.6 2.1 V ∆V I/O Controlled Voltage ∆VO Line Regulation Vi = 12 to 18 V IO = 10 mA 1 20 mV ∆VO Load Regulation IO = 5 to 250 mA ton = 30 µs toff = ≥ 1 ms 50 100 mV ∆VO Load Regulation (filter mode) Vi = 8.5 V IO = 5 to 150 mA ton = 30 µs toff = ≥ 1 ms 150 250 mV Iq Quiescent Current IO = 5 mA 1 2 mA ∆Iq Quiescent Current Change Vi = 6 to 18 V IO = 5 to 150 mA 0.05 mA ∆VO ∆T Output Voltage Drift IO = 10 mA 1.2 mV/°C SVR Supply Voltage Rejection Viac = 1 Vrms f = 100 Hz IO = 150 mA VIDC = 12 to 18 V VIDC = 6 to 11 V 70 35(*) dB dB 300 mA 500(*) 300 ms ms 145 °C Input-output Dropout Vi = 5 to 10 V IO = 5 to 150 mA ISC Short Circuit Current Ton Switch On Time TJ Thermal Shutdown Temperature 250 IO = 150 mA Vi = 5 to 11 V Vi = 11 to 18 V Junction ( *) D epending of the C FT capaci tor. Figure 1 : Test and Application Circuit. 3/8 L4916 Figure 2 : P.C. Board and Component Layout of Fig. 1 (1 : 1 scale). PRINCIPLE OF OPERATION During normal operation (input voltage upper than VI MIN = VOUT NOM + ∆VI/O). The device works as a normal voltage regulatorbuilt aroundthe OP1 of the block diagram. The series pass element use a PNP-NPN connection to reduce the dropout. The reference voltage of the OP1 is derived from a REF throughthe OP2and Q3, acting as an active zener diode of value VREF. In this conditionthe device works in the range (1) of the characteristic of the non linear drop control unit (see fig.3). The output voltage is fixed to its nominal value: R1 VOUT NOM = VREF (1 + )= R2 VCFT (1 + R1 ) R2 R1 = INTERNALLY FIXED RATIO = 2.4 R2 The ripple rejection is quite high (70 dB) and independent from CFT value. On the usualvoltage regulators, when the input voltage goes below the nominal value, the regulation transistors (series element) saturate bringing the system out of regulation making it very sensible to every variation of the input voltage. On the contrary, a control loop on the L4916 consents to avoid the saturation of the series element by regulating the value of the reference voltage (pin 2). In fact, whenever the input voltage decreases below VI MIN the supervisor loop, utilizing a non linear OTA, forces the reference voltage at pin 2 to decrease by discharging CFT. So, during the static mode, when the 4/8 input voltage goes below VMIN the drop out is kept fixed to about 1.6V. In this condition the device works as a low pass filter in the range (2) of the OTA characteristic. The ripple rejection is externally adjustable acting on CFT as follows : VI (jw) SVR (jw) = = Vout (jw) 10-6 1+ gm Where: jwCFT (1 + R1 ) R2 gm = 2 . 10-5 Ω-1 = OTA’S typical transconductance value on linear region R1 = fixed ratio R2 CFT = value of capacitor in µF The reaction time of the supervisor loop is given by the transconductanceof the OTA and by CFT. When the value of the ripple voltage is so high and its negative peak is fast enough to determine an istantaneous decrease of the dropout till 1.2 V, the OTA works in a higher transconductance condition [range (3) of the characteristic] and discharge the capacitor rapidously. If the ripple frequency is high enough the capacitor won’t charge itself completely, and the output voltage reachesa small value allowinga betterripple rejection ; the device’s again working as a filter (fast transient range). With CFT = 10 µF; f = 100Hz a SVR of 35is obtained. L4916 Figure 3 : Nonliner Transfer Characteristic of the Drop Control Unit. 1) Normal operating range (high ripple rejection) 2) Drop controlled range (medium ripple rejection) 3) Fast discharge of CFT Figure 4 : SupplyVoltage Rejection vs. Input Voltage. Figure 5 : Supply voltage Rejection vs. Frequency. Figure 6 : Vo vs. Supply Voltage. Figure 7 : Quiescent Current vs. Input Voltage. 5/8 L4916 Figure 8 : Dropout vs. Load Current. Figure 9 : Inhibit Function Realized on CFT Pin. 6/8 L4916 mm DIM. MIN. A TYP. inch MAX. MIN. 3.3 TYP. MAX. 0.130 a1 0.7 B 1.39 1.65 0.055 0.065 B1 0.91 1.04 0.036 0.041 b b1 0.028 0.5 0.38 0.020 0.5 D 0.015 0.020 9.8 0.386 E 8.8 0.346 e 2.54 0.100 e3 7.62 0.300 e4 7.62 0.300 F 7.1 0.280 I 4.8 0.189 L Z 3.3 0.44 OUTLINE AND MECHANICAL DATA 0.130 1.6 0.017 PowerMinidip 0.063 7/8 L4916 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2000 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A. http://www.st.com 8/8