1 TC7129 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ GENERAL DESCRIPTION Count Resolution ......................................... ±19,999 Resolution on 200 mV Scale .......................... 10 µV True Differential Input and Reference Low Power Consumption ................... 500 µA at 9V Direct LCD Driver for 4-1/2 Digits, Decimal Points, Low-Battery Indicator, and Continuity Indicator Overrange and Underrange Outputs Range Select Input ............................................ 10:1 High Common-Mode Rejection Ratio ......... 110 dB External Phase Compensation Not Required The TC7129 is a 4-1/2 digit analog-to-digital converter (ADC) that directly drives a multiplexed liquid crystal display (LCD). Fabricated in high-performance, low-power CMOS, the TC7129 ADC is designed specifically for highresolution, battery-powered digital multimeter applications. The traditional dual-slope method of A/D conversion has been enhanced with a successive integration technique to produce readings accurate to better than 0.005% of full scale, and resolution down to 10 µV per count. The TC7129 includes features important to multimeter applications. It detects and indicates low-battery condition. A continuity output drives an annunciator on the display, and can be used with an external driver to sound an audible alarm. Overrange and underrange outputs and a rangechange input provide the ability to create auto-ranging instruments. For snapshot readings, the TC7129 includes a latch-and-hold input to freeze the present reading. This combination of features makes the TC7129 the ideal choice for full-featured multimeter and digital measurement applications. ORDERING INFORMATION Part No. TC7129CKW TC7129CLW TC7129CPL 2 Pin Layout Formed — Normal Package Temperature Range 44-Pin PQFP 44-Pin PLCC 40-Pin PDIP 0°C to +70°C 0°C to +70°C 0°C to +70°C 3 4 5 TYPICAL OPERATING CIRCUIT LOW BATTERY CONTINUITY V+ 5 pF 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 6 120 kHz TC7129 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 330 kΩ * 0.1 µF 1 µF + 7 10 pF 0.1 µF 20 kΩ TC04 150 kΩ 0.1 µF V+ 10 kΩ + 100 kΩ 9V – + VIN 8 * NOTE: RC network between pins 26 and 28 is not required. TC7129-5 10/18/96 TELCOM SEMICONDUCTOR, INC. 3-231 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS TC7129 ABSOLUTE MAXIMUM RATINGS* (V+ V–) ............................................ 15V Supply Voltage to Reference Voltage (REF HI or REF LO) .............. V+ to V– Input Voltage (IN HI or IN LO) (Note 1) ................ V+ to V– VDISP ................................................V+ to (DGND – 0.3V) Digital Input, Pins 1, 2, 19, 20, 21, 22, 27, 37, 39, 40 .......... DGND to V+ Analog Input, Pins 25, 29, 30 ............................... V+ to V– Package Power Dissipation (TA ≤ 70°C) Plastic DIP ........................................................1.23W PLCC ................................................................1.23W Plastic QFP .......................................................1.00W Operating Temperature Range .................... 0°C to +70°C Storage Temperature Range ................ – 65°C to +150°C Lead Temperature (Soldering, 10 sec) ................. +300°C Notes: Input voltages may exceed supply voltages, provided input current is limited to ±400 µA. Currents above this value may result in invalid display readings but will not destroy the device if limited to ±1 mA. Dissipation ratings assume device is mounted with all leads soldered to printed circuit board. *Static-sensitive device. Unused devices must be stored in conductive material. Protect devices from static discharge and static fields. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to Absolute Maximum Rating Conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS: V+ to V– = 9V, VREF = 1V, TA = +25°C, fCLK = 120 kHz, unless otherwise indicated. Pin numbers refer to 40-pin DIP. Symbol Parameter Test Conditions Min Zero Input Reading Zero Reading Drift Ratiometric Reading Range Change Accuracy VIN = 0V, 200 mV Scale VIN = 0V, 0°C < TA < +70°C VIN = VREF = 1000 mV, Range = 2V VIN = 0.1V on Low Range 4VIN = 1V on High Range –VIN = +VIN = 199 mV 200 mV Scale VCM = 1V, VIN = 0V, 200 mV Scale VIN = 0V 200 mV Scale VIN = 0V 200 mV Scale VIN = 0V, Pins 32, 33 VIN = 199 mV, 0°C < TA < +70°C External VREF = 0 ppm/°C Typ Max Unit Input RE NL CMRR CMVR Roll-Over Error Linearity Error Common-Mode Rejection Ratio Common-Mode Voltage Range eN Noise (Peak-to-Peak Value Not Exceeded 95% of Time) Input Leakage Current Scale Factor Temperature Coefficient IIN Power VCOM DGND IS fCLK – 0000 0000 — ±0.5 9997 9999 0.9999 1.0000 +0000 — 10000 1.0001 Counts µV/°C Counts Ratio — — — — — — 1 1 110 (V–) +1.5 (V+) –1 14 2 — — — — — Counts Counts dB V V µVP-P — — 1 2 10 7 pA ppm/°C 3.2 0.6 10 5.3 1.2 9 0.8 120 50 7.2 3.5 — — 5.8 — 12 1.3 360 — 7.7 V mA µA V mA V mA kHz kΩ V 200 200 2 — 400 10 mV mV µA Common Voltage Common Sink Current Common Source Current Digital Ground Voltage Sink Current Supply Voltage Range Supply Current Excluding Common Current Clock Frequency VDISP Resistance Low-Battery Flag Activation Voltage V+ to Pin 28 ∆Common = +0.1V ∆Common = –0.1V V+ to Pin 36, V+ to V– = 9V ∆DGND = +0.5V V+ to V– V+ to V– = 9V VDISP to V+ V+ to V– 2.8 — — 4.5 — 6 — — — 6.3 Continuity Comparator Threshold Voltages Pull-Down Current VOUT Pin 27 = High VOUT Pin 27 = Low Pins 37, 38, 39 100 — — Digital 3-232 TELCOM SEMICONDUCTOR, INC. 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS 1 TC7129 ELECTRICAL CHARACTERISTICS: V+ to V– = 9V, VREF = 1V, TA = +25°C, fCLK = 120 kHz, unless otherwise indicated. Pin numbers refer to 40-pin DIP. Symbol Parameter Test Conditions "Weak Output" Current Sink/Source Pin 22 Source Current Pin 22 Sink Current Pins 20, 21 Sink/Source Pin 27 Sink/Source Min Typ Max — — — — 3/3 3/9 40 3 — — — — Unit µA µA µA µA PIN CONFIGURATIONS 1 40 OSC2 2 39 ANNUNICATOR DRIVE 3 38 DP2 B1, C1, CONT 4 37 RANGE A1, G1, D1 5 36 DGND F1, E1, DP1 6 35 REF LO B2, C2, LO BATT 7 34 REF HI A2, G2, D2 8 33 IN HI F2, E2, DP2 9 32 B3, C3, MINUS 10 DISPLAY A3, G3, D3 11 OUTPUT F LINES 3, E3, DP3 12 B4, C4, BC5 13 31 TC7129CPL 4 IN LO BUFF – 30 CREF + 29 CREF 28 COM 14 27 CONT 15 26 INT OUT BP3 16 BP2 17 25 INT IN + 24 V BP1 18 23 V – VDISP DP4/OR 19 22 LATCH/HOLD 20 21 DP3/UR F1, E1, DP1 1 33 REF LO 32 REF HI B2, C2, BATT 2 A2, G2, D2 3 31 IN HI DP1 DP2 RANGE DGND 34 OSC2 35 NC DGND 36 OSC1 RANGE 37 OSC3 DP2 38 A.D. DP1 41 40 39 B1, C1, CONT OSC2 42 5 A1, G1, D1 NC 44-Pin QFP OSC1 3 DP1 A4, G4, D4 F4, E4, DP4 OSC3 44 43 OSC1 OSC3 A.D. B1, C1, CONT A1, G1, D1 40-Pin PDIP 6 5 4 3 2 1 44 43 42 41 40 44-Pin PLCC 6 F1, E1, DP1 7 39 REF LO B2, C2, BATT A2, G2, D2 8 38 REF HI 9 37 IN HI F2, E2, DP2 4 30 IN LO F2, E2, DP2 10 36 IN LO B3, C3, MINUS 5 29 BUFF B3, C3, MINUS 11 35 BUFF NC 6 28 NC TC7129CKW NC 12 34 NC TC7129CLW 7 – 27 CREF A3, G3, D3 13 33 CREF F3, E3, DP3 8 26 C + REF F3, E3, DP3 14 32 CREF 25 COM B4, C4, BC5 15 31 COM 24 CONT A4, G4, D4 16 30 CONT 21 22 23 24 25 26 27 28 LATCH/HOLD V– V+ INT IN V+ 20 DP3/UR V– 18 19 NC LATCH/HOLD TELCOM SEMICONDUCTOR, INC. 29 INT OUT F4, E4, DP4 17 DP4/OR 21 22 VDISP 20 BP1 19 INT IN 18 DP3/UR VDISP 17 NC BP1 DP4/OR 15 16 BP2 14 BP3 23 INT OUT 12 13 BP2 F4, E4, DP4 11 + BP3 A4, G4, D4 10 7 – A3, G3, D3 B4, C4, BC5 9 2 8 3-233 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS TC7129 PIN DESCRIPTIONS Pin No. 40-Pin TC7129CPL 3-234 Pin No. 44-Pin TC7129CKW Pin No. 44-Pin TC7129CLW Symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40 41 2 3 43 44 1 2 3 4 5 7 8 9 10 11 12 13 14 15 16 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 OSC1 OSC3 ANNUNCIATOR B1, C1, CONT A1, G1, D1 F1, E1, DP1 B2, C2, LO BATT A2, G2, D2 F2, E2, DP2 B3, C3, MINUS A3, G3, D3 F3, E3, DP3 B4, C4, BC5 A4, D4, G4 F4, E4, DP4 BP3 BP2 BP1 VDISP DP4/OR 21 18 24 DP3/UR 22 19 25 LATCH/HOLD 23 24 20 26 27 V– V+ 25 26 27 21 23 24 28 29 30 INT IN INT OUT CONTINUITY 28 25 31 COMMON 29 30 31 32 33 26 27 29 30 31 32 33 35 36 37 C+REF C–REF BUFFER IN LO IN HI Function Input to first clock inverter. Output of second clock inverter. Backplane square-wave output for driving annunciators. Output to display segments. Output to display segments. Output to display segments. Output to display segments. Output to display segments. Output to display segments. Output to display segments. Output to display segments. Output to display segments. Output to display segments. Output to display segments. Output to display segments. Backplane #3 output to display. Backplane #2 output to display. Backplane #1 output to display. Negative rail for display drivers. Input: When HI, turns on most significant decimal point. Output: Pulled HI when result count exceeds ±19,999. Input: Second most significant decimal point on when HI. Output: Pulled HI when result count is less than ±1000. Input: When floating, ADC operates in the free-run mode. When pulled HI, the last displayed reading is held. When pulled LO, the result counter contents aren shown inincrementing during the deintegrate phase of cycle. Output: Negative-going edge occurs when the data latches are updated. Can be used for converter status signal. Negative power supply terminal. Positive power supply terminal and positive rail for display drivers. Input to integrator amplifier. Output of integrator amplifier. Input: When LO, continuity flag on the display is OFF. When HI, continuity flag is ON. Output: HI when voltage between inputs is less than +200 mV. LO when voltage between inputs is more than +200 mV. Sets common-mode voltage of 3.2V below V + for DE, 10X, etc. Can be used as preregulator for external reference. Positive side of external reference capacitor. Negative side of external reference capacitor. Output of buffer amplifier. Negative input voltage terminal. Positive input voltage terminal. TELCOM SEMICONDUCTOR, INC. 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS 1 TC7129 PIN DESCRIPTIONS 2 Pin No. 40-Pin TC7129CPL Pin No. 44-Pin TC7129CKW Pin No. 44-Pin TC7129CLW Symbol Function 34 35 36 32 33 34 38 39 40 REF HI REF LO DGND 37 35 41 RANGE 38 39 40 36 37 38 42 43 44 DP2 DP1 OSC2 Positive reference voltage in Negative reference voltage Internal ground reference for digital section. See "±5V Power Supply" paragraph. 3 µA pull-down for 200 mV scale. Pulled HI externally for 2V scale. Internal 3 µA pull-down. When HI, decimal point 2 will be on. Internal 3 µA pull-down. When HI, decimal point 1 will be on. Output of first clock inverter. Input of second clock inverter. 6,17, 28, 39 12, 23, 34,1 NC No Connection COMPONENT SELECTION (All pin designations refer to 40-Pin Dip) The TC7129 is designed to be the heart of a highresolution analog measurement instrument. The only additional components required are a few passive elements, a voltage reference, an LCD, and a power source. Most component values are not critical; substitutes can be chosen based on the information given below. The basic circuit for a digital multimeter application is shown in Figure 1. See "Special Applications" for variations. Typical values for each component are shown. The sections below give component selection criteria. Oscillator (XOSC, CO1, CO2, RO) The primary criterion for selecting the crystal oscillator is to chose a frequency that achieves maximum rejection of line-frequency noise. To do this, the integration phase should last an integral number of line cycles. The integration phase of the TC7129 is 10,000 clock cycles on the 200 mV range and 1000 clock cycles on the 2V range. One clock cycle is equal to two oscillator cycles. For 60 Hz rejection, the oscillator frequency should be chosen so that the period of one line cycle equals the integration time for the 2V range: 1/60 second = 16.7 msec = 1000 clock cycles * 2 osc cycles/clock cycle , oscillator frequency 3 4 The resistor and capacitor values are not critical; those shown work for most applications. In some situations, the capacitor values may have to be adjusted to compensate for parasitic capacitance in the circuit. The capacitors can be low-cost ceramic devices. Some applications can use a simple RC network instead of a crystal oscillator. The RC oscillator has more potential for jitter, especially in the least significant digit. See "RC Oscillator." 5 Integrating Resistor (RINT) The integrating resistor sets the charging current for the integrating capacitor. Choose a value that provides a current between 5 µA and 20 µA at 2V, the maximum fullscale input. The typical value chosen gives a charging current of 13.3 µA: ICHARGE = 6 2V 13.3 µA 150 kΩ Too high a value for RINT increases the sensitivity to noise pickup and increases errors due to leakage current. Too low a value degrades the linearity of the integration, leading to inaccurate readings. 7 giving an oscillator frequency of 120 kHz. A similar calculation gives an optimum frequency of 100 kHz for 50 Hz rejection. 8 TELCOM SEMICONDUCTOR, INC. 3-235 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS TC7129 LOW BATTERY CONTINUITY + V 14 13 11 12 9 10 7 8 6 5 4 ANNUNC OSC3 REF HI REF LO DGND RANGE DP2 DP1 OSC2 27 28 30 29 31 1 IN HI 26 2 IN LO 25 32 33 34 35 36 37 38 39 40 TC7129 BUFFER 24 CREF– CREF+ COMMON 23 3 OSC1 15 CONTINUITY VDISP 22 16 DISPLAY DRIVE OUTPUTS V– LATCH/ HOLD DP3 /UR 21 17 INT OUT DP4 /OR 18 INT IN 19 V+ 20 5 pF CO1 120 kHz CRYSTAL 330 kΩ RO 10 pF CINT 0.1 µF CREF 1 µf + 150 kΩ RINT + 9V RREF DREF 20 kΩ 0.1 µF V+ TC04 CIF 10 kΩ RBIAS CRF 0.1 µF CO2 RIF 100 kΩ – + V IN Figure 1. 3-236 Standard Circuit TELCOM SEMICONDUCTOR, INC. 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS 1 TC7129 Integrating Capacitor (CINT) Voltage Reference (DREF, RREF, RBIAS, CRF) The charge stored in the integrating capacitor during the integrate phase is directly proportional to the input voltage. The primary selection criterion for CINT is to choose a value that gives the highest voltage swing while remaining within the high-linearity portion of the integrator output range. An integrator swing of 2V is the recommended value. The capacitor value can be calculated from the equation: A TC04 band-gap reference provides a high-stability voltage reference of 1.25V. The reference potentiometer (RREF) provides an adjustment for adjusting the reference voltage; any value above 20 kΩ is adequate. The bias resistor (RBIAS) limits the current through DREF to less than 150 µA. The reference filter capacitor (CRF) forms an RC filter with RBIAS to help eliminate noise. Input filter (RIF, CIF) tINT x IINT CINT = , VSWING where tINT is the integration time. Using the values derived above (assuming 60 Hz operation), the equation becomes: CINT = 16.7msec x 13.3 µA = 0.1 µF. 2V The capacitor should have low dielectric absorption to ensure good integration linearity. Polypropylene and Teflon capacitors are usually suitable. A good measurement of the dielectric absorption is to connect the reference capacitor across the inputs by connecting: Pin to Pin 20 → 33 (CREF+ to IN HI) 30 → 32 (CREF– to IN LO) For added stability, an RC input noise filter is usually included in the circuit. The input filter resistor value should not exceed 100 kΩ. A typical RC time constant value is 16.7msec to help reject line-frequency noise. The input filter capacitor should have low leakage for a high-impedance input. 2 3 4 Battery The typical circuit uses a 9V battery as a power source. Any value between 6V and 12V can be used. For operation from batteries with voltages lower than 6V and for operation from power supplies, see "Powering the TC7129." SPECIAL APPLICATIONS The TC7129 as a Replacement Part A reading between 10,000 and 9998 is acceptable; anything lower indicates unacceptably high dielectric absorption. The TC7129 is a direct pin-for-pin replacement part for the ICL7129. Note, however, that part requires a capacitor and resistor between pins 26 and 28 for phase compensation. Since the TC7129 uses internal phase compensation, these parts are not required and, in fact, must be removed from the circuit for stable operation. Reference Capacitor (CREF) Powering the TC7129 The reference capacitor stores the reference voltage during several phases of the measurement cycle. Low leakage is the primary selection criterion for this component. The value must be high enough to offset the effect of stray capacitance at the capacitor terminals. A value of at least 1 µF is recommended. While the most common power source for the TC7129 is a 9V battery, there are other possibilities. Some of the more common ones are explained below. 5 6 7 8 TELCOM SEMICONDUCTOR, INC. 3-237 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS TC7129 ±5V Power Supply Measurements are made with respect to power supply ground. DGND (pin 36) is set internally to about 5V less than V+ (pin 24); it is not intended as a power supply input and must not be tied directly to power supply ground. (It can be used as a reference for external logic, as explained in "Connecting to External Logic." (See Figure 2.) 24 V+ REF HI 36 + 3.8V TO 6V REF LO COM TC7129 IN HI IN LO V– 2 REF HI 0.1 µF + TC04 REF LO 36 8 34 10 µF TC7660 35 28 33 32 + VIN – 23 4 5 DGND COM 0.1 µF IN HI TC7129 0.1 µF 35 TC04 DGND +5V 24 + V 34 IN LO V– 28 33 32 10 µF 3 + + VIN – Figure 3. Powering the TC7129 From a Low-Voltage Battery 23 +5V –5V Figure 2. Powering the TC7129 From a ±5V Power Supply 24 V+ Low-Voltage Battery Source Connecting to External Logic External logic can be directly referenced to DGND (pin 36), provided that the supply current of the external logic does not exceed the sink current of DGND (Figure 5). A safe value for DGND sink current is 1.2 mA. If the sink current is expected to exceed this value, a buffer is recommended. (See Figure 6.) 3-238 TC04 35 36 DGND 28 0.1 µF 33 +5V Power Supply Measurements are made with respect to power supply ground. COMMON (pin 28) is connected to REF LO (pin 35). A voltage doubler is needed, since the supply voltage is less than the 6V minimum needed by the TC7129. DGND (pin 36) must be isolated from power supply ground. (See Figure 4.) 34 0.1 µF A battery with voltage between 3.8V and 6V can be used to power the TC7129 when used with a voltage-doubler circuit as shown in Figure 3. The voltage doubler uses the TC7660 DC-to-DC voltage converter and two external capacitors. TC7129 8 V+ 32 V– 2 + + VIN – 23 10 µF TC7660 4 5 GND 3 10 µF + Figure 4. Powering the TC7129 From a +5V Power Supply TELCOM SEMICONDUCTOR, INC. 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS 1 TC7129 V+ V 2 + 24 24 EXTERNAL LOGIC EXTERNAL LOGIC TC7129 36 DGND ILOGIC + 36 DGND ILOGIC 23 23 V– V Figure 5. External Logic Referenced Directly to DGND 3 TC7129 – – Figure 6. External Logic Referenced to DGND With Buffer 4 Temperature Compensation For most applications, VDISP (pin 19) can be connected directly to DGND (pin 36). For applications with a wide temperature range, some LCDs require that the drive levels vary with temperature to maintain good viewing angle and display contrast. Figure 7 shows two circuits that can be adjusted to give temperature compensation of about 10 mV/°C between V+ (pin 24) and VDISP. The diode between DGND and VDISP should have a low turn-ON voltage because VDISP cannot exceed 0.3V below DGND. V+ 1N4148 V+ 39 kΩ 24 20 kΩ 19 5 kΩ 2N2222 TC7129 – + 36 6 39 kΩ 24 200 kΩ 5 TC7129 19 VDISP VDISP 7 36 DGND DGND 75 kΩ 18 kΩ 23 V– Figure 7. TELCOM SEMICONDUCTOR, INC. 23 V– 8 Temperature Compensating Circuits 3-239 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS TC7129 RC Oscillator For applications in which 3-1/2 digit (100 µV) resolution is sufficient, an RC oscillator is adequate. A recommended value for the capacitor is 51 pF. Other values can be used as long as they are sufficiently larger than the circuit parasitic capacitance. The resistor value is calculated from: R= 0.45 freq * C For 120 kHz frequency and C = 51 pF, the calculated value of R is 75 kΩ. The RC oscillator and the crystal oscillator circuits are shown in Figure 8. measurement of the time to ramp the integrated voltage to zero, and is therefore proportional to the input voltage being measured. This count can then be scaled and displayed as a measurement of the input voltage. Figure 9 shows the phases of the dual-slope conversion. The dual-slope method has a fundamental limitation. The count can only stop on a clock cycle, so that measurement accuracy is limited to the clock frequency. In addition, a delay in the zero-crossing comparator can add to the inaccuracy. Figure 10 shows these errors in an actual measurement. DEINTEGRATE INTEGRATE Measuring Techniques Two important techniques are used in the TC7129: successive integration and digital auto-zeroing. Successive integration is a refinement to the traditional dual-slope conversion technique. ZERO CROSSING Dual-Slope Conversion TIME A dual-slope conversion has two basic phases: integrate and deintegrate. During the integrate phase, the input signal is integrated for a fixed period of time; the integrated voltage level is thus proportional to the input voltage. During the deintegrate phase, the integrated voltage is ramped down at a fixed slope, and a counter counts the clock cycles until the integrator voltage crosses zero. The count is a 1 5 pF 40 120 kHz Figure 9. Dual-Slope Conversion Successive Integration The successive integration technique picks up where dual-slope conversion ends. The overshoot voltage shown in Figure 10, called the "integrator residue voltage," is measured to obtain a correction to the initial count. Figure 11 shows the cycles in a successive integration measurement. The waveform shown is for a negative input signal. The sequence of events during the measurement cycle is: TC7129 Phase Description 2 INT1 Input signal is integrated for fixed time. (1000 clock cycles on 2V scale, 10,000 on 200 mV) Integrator voltage is ramped to zero. Counter counts up until zero crossing to produce reading accurate to 3-1/2 digits. Residue represents an overshoot of the actual input voltage. Rest; circuit settles. Residue voltage is amplified 10 times and inverted. Integrator voltage is ramped to zero. Counter counts down until zero crossing to correct reading to 4-1/2 digits. Residue represents an undershoot of the actual input voltage. Rest; circuit settles. Residue voltage is amplified 10 times and inverted. Integrator voltage is ramped to zero. Counter counts up until zero crossing to correct reading to 5-1/2 digits. Residue is discarded. 270 kΩ 10 pF DE1 V+ V+ REST X10 DE2 TC7129 1 40 2 75 kΩ 51 pF REST X10 DE3 Figure 8. Oscillator Circuits 3-240 TELCOM SEMICONDUCTOR, INC. 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS 1 TC7129 2 DEINTEGRATE INTEGRATE OVERSHOOT DUE TO ZERO CROSSING BETWEEN CLOCK PULSES TIME OVERSHOOT CAUSED BY COMPARATOR DELAY OF 1 CLOCK PULSE CLOCK PULSES Figure 10. ZERO INTEGRATE AND LATCH 3 INTEGRATOR RESIDUE VOLTAGE INT1 INTEGRATE 4 Accuracy Errors in Dual-Slope Conversion DE1 DEINTEGRATE REST X10 DE2 REST X10 DE3 ZERO INTEGRATE 5 TC7129 6 NOTE: Shaded area greatly expanded in time and amplitude. INTEGRATOR RESIDUAL VOLTAGE Figure 11. Integrator Waveform Digital Auto-Zeroing Inside the TC7129 To eliminate the effect of amplifier offset errors, the TC7129 uses a digital auto-zeroing technique. After the input voltage is measured as described above, the measurement is repeated with the inputs shorted internally. The reading with inputs shorted is a measurement of the internal errors and is subtracted from the previous reading to obtain a corrected measurement. Digital auto-zeroing eliminates the need for an external auto-zeroing capacitor used in other ADCs. Figure 12 shows a simplified block diagram of the TC7129. TELCOM SEMICONDUCTOR, INC. 7 Integrator Section The integrator section includes the integrator, comparator, input buffer amplifier, and analog switches used to change the circuit configuration during the separate measurement phases described earlier. 3-241 8 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS TC7129 LOW BATTERY SEGMENT DRIVES CONTINUITY BACKPLANE DRIVES ANNUNCIATOR DRIVE OSC1 LATCH, DECODE DISPLAY MULTIPLEXER VDISP OSC2 UP/DOWN RESULTS COUNTER OSC3 SEQUENCE COUNTER/DECODER CONTROL LOGIC RANGE L/H CONT DP1 DP2 UR/DP3 OR/DP4 V+ V– ANALOG SECTION REF HI REF LO DGND INT OUT TC7129 INT IN COMMON IN IN HI LO Figure 12. 3-242 BUFF Functional Block Diagram TELCOM SEMICONDUCTOR, INC. 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS 1 TC7129 CREF REF HI RINT CINT 2 REF LO DE DE INTEGRATOR – INT1 10 pF – + IN HI DE– DE+ BUFFER X10 COMPARATOR 1 + – 100 pF DE– DE+ COMMON INT INT1, INT2 TO DIGITAL SECTION + COMPARATOR 2 ZI, X10 3 REST IN LO – + V 200 mV – CONTINUITY + 500 kΩ Figure 13. 4 TC7129 CONTINUITY COMPARATOR TO DISPLAY DRIVER Integrator Block Diagram Table I. Switch Legends Label Meaning DE DE– Open during all deintegrate phases. Closed during all deintegrate phases when input voltage is negative. Closed during all deintegrate phases when input voltage is positive. Closed during the first integrate phase (measurement of the input voltage). Closed during the second integrate phase (measurement of the amplifier offset). Open during both integrate phases. Closed during the rest phase. Closed during the zero-integrate phase. Closed during the X10 phase. Open during the X10 phase. DE+ INT1 INT2 INT REST ZI X10 X10 5 – + IN HI 6 COM TC7129 IN LO – 200 mV The buffer amplifier has a common-mode input voltage range from 1.5V above V– to 1V below V+. The integrator amplifier can swing to within 0.3V of the rails, although for best linearity the swing is usually limited to within 1V. Both amplifiers can supply up to 80 µA of output current, but should be limited to 20 µA for good linearity. Continuity Indicator A comparator with a 200 mV threshold is connected between IN HI (pin 33) and IN LO (pin 32). Whenever the voltage between inputs is less than 200 mV, the TELCOM SEMICONDUCTOR, INC. BUFFER V + 500 kΩ TO DISPLAY DRIVER (NOT LATCHED) CONT Figure 14. 7 Continuity Indicator Circuit CONTINUITY output (pin 27) will be pulled HIGH, activating the continuity annunciator on the display. The continuity pin can also be used as an input to drive the continuity annunciator directly from an external source. A schematic of the input/output nature of this pin is shown in Figure 15. 3-243 8 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS TC7129 Sequence and Results Counter A sequence counter and associated control logic provide signals that operate the analog switches in the integrator section. The comparator output from the integrator gates the results counter. The results counter is a six-section up/ down decade counter which holds the intermediate results from each successive integration. TC7129 '500 kΩ DP4/OR, PIN 20 DP3/UR, PIN 21 LATCH/HOLD PIN 22 CONTINUITY, PIN 27 Overrange and Underrange Outputs The common and digital ground (DGND) outputs are generated from internal zener diodes. The voltage between V+ and DGND is the internal supply voltage for the digital section of the TC7129. Common can source approximately 12 µA; DGND has essentially no source capability. When the results counter holds a value greater than ±19,999, the DP4/OR output (pin 20) is driven HIGH. When the results counter value is less than ±1000, the DP3/UR output (pin 21) is driven HIGH. Both signals are valid on the falling edge of LATCH/HOLD (L/H) and do not change until the end of the next conversion cycle. The signals are updated at the end of each conversion unless the L/H input (pin 22) is held HIGH. Pins 20 and 21 can also be used as inputs for external control of decimal points 3 and 4. Figure 15 shows a schematic of the input/output nature of these pins. Low Battery Latch/Hold The low battery annunciator turns on when supply voltage between V+ and V– drops below 6.8V. The internal zener has a threshold of 6.3V. When the supply voltage drops below 6.8V, the transistor tied to V– turns OFF, pulling the "Low Battery" point HIGH. (See Figure 16.) The L/H output goes LOW during the last 100 cycles of each conversion. This pulse latches the conversion data into the display driver section of the TC7129. This pin can also be used as an input. When driven HIGH, the display will not be updated; the previous reading is displayed. When driven LOW, the display reading is not latched; the sequence counter reading will be displayed. Since the counter is counting much faster than the backplanes are being updated, the reading shown in this mode is somewhat erratic. Figure 15. Input/Output Pin Schematic Common and Digital Ground 24 12 µA V + 3.2V 28 Display Driver COM – 5V N + LOGIC SECTION 36 P DGND N TC7129 23 Figure 16. 3-244 V – Digital Ground (DGND) and Common Outputs The TC7129 drives a triplexed LCD with three backplanes. The LCD can include decimal points, polarity sign, and annunciators for continuity and low battery. Figure 17 shows the assignment of the display segments to the backplanes and segment drive lines. The backplane drive frequency is obtained by dividing the oscillator frequency by 1200. This results in a backplane drive frequency of 100 Hz for 60 Hz operation (120 kHz crystal) and 83.3 Hz for 50 Hz operation (100 kHz crystal). Backplane waveforms are shown in Figure 18. These appear on outputs BP1, BP2, BP3 (pins 16, 17, and 18). They remain the same regardless of the segments being driven. Other display output lines (pins 4 through 15) have waveforms that vary depending on the displayed values. Figure 19 shows a set of waveforms for the A, G, D outputs (pins 5, 8, 11, and 14) for several combinations of "ON" segments. TELCOM SEMICONDUCTOR, INC. 4-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTER WITH ON-CHIP LCD DRIVERS 1 TC7129 LOW BATTERY 2 CONTINUITY BP1 BP2 BACKPLANE CONNECTIONS 3 BP3 LOW BATTERY CONTINUITY F4, E4, DP4 A4, G4, D4 B1, C1, CONTINUITY B4, C4, BC4 F1, E1, DP1 A1, G1, D1 F3, E3, DP3 A3, G3, D3 B2, C2, LOW BATTERY A2, G2, D2 B3, C3, MINUS F2, E2, DP2 Figure 17. 5 Display Segment Assignments VDD VH b SEGMENT LINE ALL OFF BP1 BP2 a SEGMENT ON d, g OFF BP3 a, g ON d OFF Figure 18. 4 VL VDISP VDD VH VL VDISP VDD VH VL VDISP TELCOM SEMICONDUCTOR, INC. 7 VDD VH Backplane Waveforms The ANNUNCIATOR DRIVE output (pin 3) is a squarewave running at the backplane frequency (100 Hz or 83.3 Hz), with a peak-to-peak voltage equal to DGND voltage. Connecting an annunciator to pin 3 turns it ON; connecting it to its backplane turns it OFF. 6 ALL ON VL VDISP Figure 19. 8 Typical Display Output Waveforms 3-245