TI DAC8803

DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
Quad, Current Output, Serial Input 14-Bit Multiplying Digital-to-Analog Converter
FEATURES
DESCRIPTION
•
•
•
The DAC8803 is a quad, 14-bit, current-output digital-to-analog converter (DAC) designed to operate
from a single 2.7 V to 5-V supply.
•
•
•
•
•
•
•
•
The applied external reference input voltage VREF
determines the full-scale output current. An internal
feedback resistor (RFB) provides temperature tracking
for the full-scale output when combined with an
external I-to-V precision amplifier.
A doubled buffered serial data interface offers
high-speed, 3-wire, SPI and microcontroller compatible inputs using serial data in (SDI), clock (CLK), and
a chip select (CS). In addition, a serial data out pin
(SDO) allows for daisy chaining when multiple packages are used. A common level-sensitive load DAC
strobe (LDAC) input allows simultaneous update of all
DAC outputs from previously loaded input registers.
Additionally, an internal power on reset forces the
output voltage to zero at system turn on. An MSB pin
allows system reset assertion (RS) to force all registers to zero code when MSB = 0, or to half-scale
code when MSB = 1.
APPLICATIONS
•
•
•
Automatic Test Equipment
Instrumentation
Digitally Controlled Calibration
The DAC8803 is packaged in a SSOP package.
VREFA B C D
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
A0
A1
SDO
SDI
RFBA
Input
Register
R
DAC A
Register
R
DAC A
IOUTA
AGNDA
RFBB
16
Input
Register
R
DAC B
Register
R
DAC B
IOUTC
AGNDB
RFBC
Input
Register
R
DAC C
Register
R
DAC C
IOUTC
AGNDC
CS
CLK
RFBD
EN
DAC A
B
C
D
2:4
Decode
DGND
Input
Register
R
DAC D
Register
R
DAC D
IOUTD
AGNDD
Power-on
Reset
RS
MSB
AGNDF
LDAC
VSS
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
SPI is a trademark of Motorola, Inc.
All trademarks are the property of their respective owners.
PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the
right to change or discontinue these products without notice.
Copyright © 2005, Texas Instruments Incorporated
PRODUCT PREVIEW
•
•
•
Relative Accuracy: 1 LSB Max
Differential Nonlinearity: 1 LSB Max
2-mA Full-Scale Current ±20%,
With VREF = ±10 V
0.5-µs Settling Time
Midscale or Zero-Scale Reset
Four Separate 4-Quadrant Multiplying
Reference Inputs
Reference Bandwidth: 10 MHz
Reference Dynamics: -105 dB THD
50-MHz SPI™-Compatible 3-Wire Interface
Double Buffered Registers Enable
Simultaneous Multichannel Update
Internal Power On Reset
Compact SSOP-28 Package
Industry-Standard Pin Configuration
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated
circuits be handled with appropriate precautions. Failure to observe proper handling and installation
procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision
integrated circuits may be more susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION (1)
PRODUCT
MINIMUM
RELATIVE
ACCURACY
(LSB)
DIFFERENTIAL
NONLINEARITY
(LSB)
SPECIFIED
TEMPERATURE
RANGE
PACKAGELEAD
PACKAGE
DESIGNATOR
DAC8803
±1
±1
-40°C to +85°C
SSOP-28
DB
(1)
ORDERING
NUMBER
TRANSPORT
MEDIA
QUANTITY
DAC8803IDBT
Tape and Reel, 250
DAC8803IDBR
Tape and Reel, 2500
For the most current specifications and package information, see the Package Option Addendum at the end of this document, or see the
TI website at www.ti.com
ABSOLUTE MAXIMUM RATINGS (1)
PRODUCT PREVIEW
DAC8803
UNIT
-0.3 to +8
V
VSS to GND
-0.3 to -7
V
VREF to GND
-18 to +18
V
Logic inputs and output to GND
-0.3 to +8
V
V(IOUT) to GND
-0.3 to VDD + 0.3
V
AGNDX to DGND
-0.3 to +0.3
V
±50
mA
VDD to GND
Input current to any pin except supplies
Package power dissipation
Thermal resistance, θJA
(TJmax - TA)/θJA
28-Lead shrink surface-mount (RS-28)
100
°C/W
Maximum junction temperature (TJmax)
150
°C
Operating temperature range, Model A
-40 to +85
°C
Storage temperature range
-65 to +150
°C
Lead temperature
RS-28 (Vapor phase 60s)
215
°C
Lead temperature
RS-28 (Infrared 15s)
220
°C
(1)
2
Stresses above those listed under absolute maximum ratings may cause permanent damage to the device. This is a stress rating only;
functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum conditions for extended periods may affect device reliability.
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
ELECTRICAL CHARACTERISTICS
(1)
VDD = 5 V ± 10%; VSS = 0 V, IOUTX = Virtual GND, AGNDX = 0 V, VREFA, B, C, D = 10 V, TA = full operating temperature range,
unless otherwise noted.
DAC8803
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNIT
STATIC PERFORMANCE (2)
Resolution
Relative accuracy
Differential nonlinearity
DNL
Output leakage current
IOUTX
Data = 0000h, TA = 25°C
IOUTX
Data = 0000h, TA = TA max
Full-scale gain error
GFSE
Data = FFFFh
Full-scale tempco (3)
TCVFS
Feedback resistor
RFBX
±0.75
14
Bits
±1
LSB
±1
LSB
10
nA
20
nA
±3
mV
1
ppm/°C
VDD = 5 V
kΩ
VREFX Range
VREFX
-15
Input resistance
RREFX
4
Input resistance match
RREFX
Input capacitance (3)
CREFX
Channel-to-channel
6
15
V
8
kΩ
1
%
5
pF
PRODUCT PREVIEW
REFERENCE INPUT
ANALOG OUTPUT
Output current
Output capacitance (3)
IOUTX
Data = FFFFh
COUTX
Code-dependent
1.25
2.5
80
mA
pF
LOGIC INPUTS AND OUTPUT
Input low voltage
Input high voltage
VIL
VDD = +2.7 V
0.6
V
VIL
VDD = +5 V
0.8
V
VIH
VDD = +2.7 V
2.1
V
VIH
VDD = +5 V
2.4
V
Input leakage current
IIL
1
µA
Input capacitance (3)
CIL
10
pF
0.4
V
Logic output low voltage
Logic output high voltage
INTERFACE TIMING (3),
VOL
IOL = 1.6 mA
VOH
IOH = 100 µA
4
V
tCH
25
ns
(4)
Clock width high
Clock width low
tCL
25
ns
CS to Clock setup
tCSS
0
ns
Clock to CS hold
tCSH
25
tPD
2
Clock to SDO prop delay
Load DAC pulsewidth
ns
20
ns
tLDAC
25
ns
Data setup
tDS
20
ns
Data hold
tDH
20
ns
Load setup
tLDS
5
ns
Load hold
tLDH
25
ns
SUPPLY CHARACTERISTICS
Power supply range
Positive supply current
(1)
(2)
(3)
(4)
VDD
2.7
RANGE
IDD
Logic inputs = 0 V
2
5.5
V
5
µA
Specifications subject to change without notice.
All static performance tests (except IOUT) are performed in a closed-loop system using an external precision OPA277 I-to-V converter
amplifier. The DAC8803 RFB terminal is tied to the amplifier output. Typical values represent average readings measured at 25°C.
These parameters are specified by design and not subject to production testing.
All input control signals are specified with tR = tF = 2.5 ns (10% to 90% of 3 V) and timed from a voltage level of 1.5 V.
3
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
ELECTRICAL CHARACTERISTICS (continued)
VDD = 5 V ± 10%; VSS = 0 V, IOUTX = Virtual GND, AGNDX = 0 V, VREFA, B, C, D = 10 V, TA = full operating temperature range,
unless otherwise noted.
DAC8803
PARAMETER
Negative supply current
Power dissipation
Power supply sensitivity
AC
SYMBOL
TYP
MAX
IDD
VDD = +4.5 V to +5.5 V
CONDITIONS
2
5
µA
IDD
VDD = +2.7 V to +3.6 V
1
2.5
µA
ISS
Logic inputs = 0 V, VSS = -5 V
PDISS
PSS
MIN
0.001
UNIT
1
µA
Logic inputs = 0 V
0.025
mW
∆VDD = ±5%
0.006
%
CHARACTERISTICS (5)
Output voltage settling time
Reference multiplying BW
ts
To ±0.1% of full-scale,
Data = 0000h to FFFFh to 0000h
0.5
ts
To ±0.006% of full-scale,
Data = 0000h to FFFFh to 0000h
1
µs
10
MHz
Q
VREFX = 10 V, Data = 0000h to 8000h to 0000h
1
nV/s
Feedthrough error
VOUTX/VREFX
Data = 0000h, VREFX = 100 mVRMS, f = 100 kHz
-70
Crosstalk error
VOUTA/VREFB
Data = 0000h, VREFB = 100 mVRMS,
Adjacent channel, f = 100 kHz
-90
DAC glitch impulse
PRODUCT PREVIEW
Digital feedthrough
Total harmonic distortion
Output spot noise voltage
(5)
4
BW -3 dB VREFX = 100 mVRMS, Data = FFFFH, CFB = 15 pF
µs
Q
THD
en
CS = 1 and fCLK = 1 MHz
VREF = 5 VPP, Data = FFFFh, f = 1 kHz
2
-105
f = 1 kHz, BW = 1 Hz
All ac characteristic tests are performed in a closed-loop system using an OPA627 I-to-V converter amplifier.
12
dB
dB
nV/s
dB
nV/√Hz
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
PIN CONFIGURATIONS
DAC8803
(TOP VIEW)
AGNDA
IOUTA
VREFA
RFBA
MSB
RS
VDD
CS
CLK
SDI
RFBB
VREFB
IOUTB
AGNDB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
AGNDD
IOUTD
VREFD
RFBD
DGND
VSS
AGNDF
LDAC
SDO
NC
RFBC
VREFC
IOUTC
AGNDC
PIN DESCRIPTION
PIN
NAME
1, 14, 15, 28
AGNDA, AGNDB, AGNDC, AGNDD
DAC A, B, C, D Analog ground
DESCRIPTION
2, 13, 16, 27
IOUTA, IOUTB, IOUTC, IOUTD
DAC A, B, C, D Current output
3, 12, 17, 26
VREFA, VREFB, VREFC, VREFD
DAC A, B, C, D Reference voltage input terminal. Establishes DAC A, B, C, D full-scale
output voltage. Can be tied to VDD.
4, 11, 18, 25
RFBA, RFBB, RFBC, RFBD,
Establish voltage output for DAC A, B, C, D by connecting to external amplifier output.
5
MSB
6
RS
Reset pin, active low. Input register and DAC registers are set to all zeros or half scale
code (8000h) determined by the voltage on the MSB pin. Register data = 8000h when
MSB = 1.
7
VDD
Positive power-supply input. Specified range of operation 5 V ±10%.
8
CS
Chip-select; active low input. Disables shift register loading when high. Transfers shift
register data to input register when CS/LDAC goes high. Does not affect LDAC
operation.
MSB Bit set during a reset pulse (RS) or at system power on if tied to ground or VDD
9
CLK
Clock input; positive edge triggered clocks data into shift register
10
SDI
Serial data input; data loads directly into the shift register.
19
NC
Not connected; leave floating
20
SDO
Serial data output; input data load directly into shift register. Data appears at SDO, 19
clock pulses after input at the SDI pin.
21
LDAC
Load DAC register strobe; level sensitive active low. Tranfers all input register data to
the DAC registers. Asynchronous active low input. See Table 1 for operation.
22
AGNDF
High current analog force ground.
23
VSS
24
DGND
Negative bias power-supply input. Specified range of operation -0.3 V to -5.5 V.
Digital ground.
5
PRODUCT PREVIEW
NC − No internal connection
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Channel A
LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Graphic
Forthcoming
PRODUCT PREVIEW
Figure 1.
Figure 2.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 3.
6
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 4.
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Graphic
Forthcoming
Figure 5.
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 6.
PRODUCT PREVIEW
LINEARITY ERROR
vs DIGITAL INPUT CODE
7
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Channel B
LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Graphic
Forthcoming
PRODUCT PREVIEW
Figure 7.
Figure 8.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 9.
8
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 10.
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Graphic
Forthcoming
Figure 11.
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 12.
PRODUCT PREVIEW
LINEARITY ERROR
vs DIGITAL INPUT CODE
9
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Channel C
LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Graphic
Forthcoming
PRODUCT PREVIEW
Figure 13.
Figure 14.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 15.
10
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 16.
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Graphic
Forthcoming
Figure 17.
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 18.
PRODUCT PREVIEW
LINEARITY ERROR
vs DIGITAL INPUT CODE
11
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Channel D
LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Graphic
Forthcoming
PRODUCT PREVIEW
Figure 19.
Figure 20.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 21.
12
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 22.
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Graphic
Forthcoming
Figure 23.
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 24.
PRODUCT PREVIEW
LINEARITY ERROR
vs DIGITAL INPUT CODE
13
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
SUPPLY CURRENT
vs LOGIC INPUT VOLTAGE
REFERENCE MULTIPLYING BANDWIDTH
6
0
−6
−12
−18
−24
−30
−36
−42
−48
−54
−60
−66
−72
−78
−84
−90
−96
−102
−108
−114
1.6
VDD = +5.0V
1.2
Attenuation (dB)
Supply Current, IDD (mA)
1.4
1.0
0.8
0.6
0.4
0.2
VDD = +2.7V
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
10
1k
10k
100k
1M
Figure 25.
Figure 26.
DAC GLITCH
DAC SETTLING TIME
Code: 7FFFh to 8000h
Output Voltage (5V/div)
PRODUCT PREVIEW
Output Voltage (50mV/div)
100
10M
Bandwidth (Hz)
Logic Input Voltage (V)
Voltage Output Settling
Trigger Pulse
Trigger Pulse
Time (0.2µs/div)
Time (0.1µs/div)
Figure 27.
Figure 28.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Channel A
Graphic
Forthcoming
Figure 29.
14
Graphic
Forthcoming
Figure 30.
100M
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Graphic
Forthcoming
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 31.
Figure 32.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 33.
PRODUCT PREVIEW
LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 34.
15
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Channel B
LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Graphic
Forthcoming
PRODUCT PREVIEW
Figure 35.
Figure 36.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 37.
16
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 38.
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Graphic
Forthcoming
Figure 39.
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 40.
PRODUCT PREVIEW
LINEARITY ERROR
vs DIGITAL INPUT CODE
17
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Channel C
LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Graphic
Forthcoming
PRODUCT PREVIEW
Figure 41.
Figure 42.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 43.
18
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 44.
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Graphic
Forthcoming
Figure 45.
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 46.
PRODUCT PREVIEW
LINEARITY ERROR
vs DIGITAL INPUT CODE
19
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
Channel D
LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Graphic
Forthcoming
PRODUCT PREVIEW
Figure 47.
Figure 48.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 49.
20
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Figure 50.
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
TYPICAL CHARACTERISTICS: VDD = +2.7 V (continued)
At TA = +25°C, +VDD = +2.7 V, unless otherwise noted.
LINEARITY ERROR
vs DIGITAL INPUT CODE
DIFFERENTIAL LINEARITY ERROR
vs DIGITAL INPUT CODE
Graphic
Forthcoming
Graphic
Forthcoming
Figure 52.
PRODUCT PREVIEW
Figure 51.
PARAMETER MEASUREMENT INFORMATION
SDI
A1
A0
D13 D13 D12
D11 D10
D8
D9
D7
D2
D1
CLK
Input REG. LD
tCSS
CS
D0
tds
tdh
tch
tcsh
tcl
tlds
LDAC
tpd
SDO
tLDH
tLDAC
Figure 53. DAC8803 Timing Diagram
CIRCUIT OPERATION
The DAC8803 contains four 14-bit, current-output, digital-to-analog converters respectively. Each DAC has its
own independent multiplying reference input. The DAC8803 uses a 3-wire SPI compatible serial data interface,
with a configurable asynchronous RS pin for half-scale (MSB = 1) or zero-scale (MSB = 0) preset. In addition, an
LDAC strobe enables four channel simultaneous updates for hardware synchronized output voltage changes.
D/A Converter
The DAC8803 contains four current-steering R-2R ladder DACs. Figure 54 shows a typical equivalent DAC.
Each DAC contains a matching feedback resistor for use with an external I-to-V converter amplifier. The RFBX pin
is connected to the output of the external amplifier. The IOUTX terminal is connected to the inverting input of the
external amplifier. The AGNDX pin should be Kelvin-connected to the load point in the circuit requiring the full
14-bit accuracy.
21
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
The DAC is designed to operate with both negative or positive reference voltages. The VDD power pin is only
used by the logic to drive the DAC switches on and off. Note that a matching switch is used in series with the
internal 5 kΩ feedback resistor. If users are attempting to measure the value of RFB, power must be applied to
VDD in order to achieve continuity. An additional VSS bias pin is used to guard the substrate during high
temperature applications to minimize zero-scale leakage currents that double every 10°C. The DAC output
voltage is determined by VREF and the digital data (D) according to Equation 1:
V OUT VREF D
16384
(1)
Note that the output polarity is opposite to the VREF polarity for dc reference voltages.
VDD
RRR
VREFX
RFBX
2R
2R
2R
R
5 k
S2
S1
IOUTX
AGNDF
AGNDX
PRODUCT PREVIEW
From Other DACS AGND
VCC
DGND
Digital interface connections omitted for clarity.
Switches S1 and S2 are closed, VDD must be powered.
Figure 54. Typical Equivalent DAC Channel
The DAC is also designed to accommodate ac reference input signals. The DAC8803 accommodates input
reference voltages in the range of -12 V to +12 V. The reference voltage inputs exhibit a constant nominal input
resistance of 5 kΩ, ± 20%. On the other hand, the DAC outputs IOUTA, B, C, D are code-dependent and produce
various output resistances and capacitances.
The choice of external amplifier should take into account the variation in impedance generatedby the DAC8803
on the amplifiers' inverting input node. The feedback resistance, in parallel with the DAC ladder resistance,
dominates output voltage noise. For multiplying mode applications, an external feedback compensation capacitor
(CFB) may be needed to provide a critically damped output response for step changes in reference input
voltages.
Figure 5 and Figure 6 show the gain vs frequency performance at various attenuation settings using a 23 pF
external feedback capacitor connected across the IOUTX and RFBX terminals. In order to maintain good analog
performance, power supply bypassing of 0.01 µF, in parallel with 1 µF, is recommended. Under these conditions,
clean power supply with low ripple voltage capability should be used. Switching power supplies is usually not
suitable for this application due to the higher ripple voltage and PSS frequency-dependent characteristics. It is
best to derive the DAC8803 5-V supply from the system analog supply voltages. (Do not use the digital 5-V
supply.) See Figure 55.
22
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
15 V
2R
5V
+
Analog
Power
Supply
R
VDD
RRR
RFBX
VREFX
2R
2R
2R
R
5 k
15 V
S2
S1
IOUTX
VCC
AGNDF
AGNDX
From Other DACS AGND
VSS
Digital interface connections omitted for clarity.
Switches S1 and S2 are closed, VDD must be powered.
VOUT
A1
+
VEE
Load
DGND
PRODUCT PREVIEW
Figure 55. Recommended Kelvin-Sensed Hookup
23
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
VREF A B C D
CS
EN
VDD
CLK
SDI
SDO
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
A0
A1
16
RFBA
DAC A
Register R
Input
Register R
DAC A
IOUTA
AGNDA
RFBB
DAC B
Register R
Input
Register R
DAC B
ADC A
B
C
D
2:4
Decode
IOUTC
AGNDB
RFBC
DAC C
Register R
PRODUCT PREVIEW
Input
Register R
DAC C
IOUTC
AGNDC
RFBD
DAC D
Register R
Input
Register R
DAC D
IOUTD
AGNDD
Set MSB
Set
MSB
Poweron
Reset
DGND
AGNDF
MSB
LDAC
RS
VSS
Figure 56. System Level Digital Interfacing
SERIAL DATA INTERFACE
The DAC8803 uses a 3-wire (CS, SDI, CLK) SPI compatible serial data interface. Serial data of the DAC8803 is
clocked into the serial input register in an 14-bit data-word format. MSB bits are loaded first. Table 3 defines the
16 data-word bits for the DAC8803.
Data is placed on the SDI pin, and clocked into the register on the positive clock edge of CLK subject to the data
setup and data hold time requirements specified in the Interface Timing Specifications. Data can only be clocked
in while the CS chip select pin is active low. For the DAC8803, only the last 16 bits clocked into the serial register
are interrogated when the CS pin returns to the logic high state.
Since most microcontrollers output serial data in 8-bit bytes, three right-justified data bytes can be written to the
DAC8803. Keeping the CS line low between the first, second, and third byte transfers results in a successful
serial register update. Similarly, two right-justified data bytes can be written to the DAC8803. Keeping the CS line
low between the first and second byte transfer will result in a successful serial register update.
24
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
Once the data is properly aligned in the shift register, the positive edge of the CS initiates the transfer of new
data to the target DAC register, determined by the decoding of address bits A1and A0. For DAC8803, Table 1,
Table 3 and Figure 57 define the characteristics of the software serial interface. Figures 8 and 9 show the
equivalent logic interface for the key digital control pins for DAC8803.
To Input Register
Address
Decoder
CS
A
B
C
D
EN
Shift Register
CLK
SDI
19th/17th
CLOCK
SDO
Two additional pins RS and MSB provide hardware control over the preset function and DAC register loading. If
these functions are not needed, the RS pin can be tied to logic high. The asynchronous input RS pin forces all
input and DAC registers to either the zero-code state (MSB = 0), or the half-scale state (MSB = 1).
POWER ON RESET
When the VDD power supply is turned on, an internal reset strobe forces all the Input and DAC registers to the
zero-code state or half-scale, depending on the MSB pin voltage. The VDD power supply should have a smooth
positive ramp without drooping in order to have consistent results, especially in the region of VDD = 1.5 V to 2.3
V. The VSS supply has no effect on the power-on reset performance. The DAC register data stays at zero or
half-scale setting until a valid serial register data load takes place.
ESD Protection Circuits
All logic-input pins contain back-biased ESD protection Zener diodes connected to ground (DGND) and VDD as
shown in Figure 58.
VDD
DIGITAL
INPUTS
5 k
DGND
Figure 58. Equivalent ESD Protection Circuits
25
PRODUCT PREVIEW
Figure 57. DAC8803 Equivalent Logic Interface
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
PCB LAYOUT
In printed circuit board (PCB) layout, all analog ground, AGNDX, should be tied together. Amplifiers suitable for:
Table 1. Control Logic Truth Table (1)
CS
CLK
LDAC
RS
MSB
H
X
H
H
X
No effect
Latched
Latched
L
L
H
H
X
No effect
Latched
Latched
L
↑+
H
H
X
Shift register data advanced one bit
Latched
Latched
L
H
H
H
X
No effect
Latched
Latched
↑+
L
H
H
X
No effect
Selected DAC updated with current SR
contents
Latched
H
X
L
H
X
No effect
Latched
Transparent
H
X
H
H
X
No effect
Latched
Latched
H
X
↑+
H
X
No effect
Latched
Latched
H
X
H
L
0
No effect
Latched data = 0000h
Latched data = 0000h
X
↑+
H
L
H
No effect
Latched data = 8000h
Latched data = 8000h
(1)
SERIAL SHIFT REGISTER
INPUT REGISTER
DAC REGISTER
↑+ Positive logic transition; X = Do not care
Table 2. Serial Input Register Data Format, Data Loaded MSB First (1)
PRODUCT PREVIEW
Bit
B17
(MSB)
B16
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
(LSB)
Data
A1
A0
X
X
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
(1)
Only the last 18 bits of data clocked into the serial register (address + data) are inspected when the CS line's positive edge returns to
logic high. At this point an internally generated load strobe transfers the serial register data contents (bits D13-D0) to the decoded
DAC-input-register address determined by bits A1 and A0. Any extra bits clocked into the DAC8803 shift register are ignored, only the
last 18 bits clocked in are used. If double-buffered data is not needed, the LDAC pin can be tied logic low to disable the DAC registers.
Table 3. Address Decode
26
A1
A0
DAC DECODE
0
0
DAC A
0
1
DAC B
1
0
DAC C
1
1
DAC D
DAC8803
www.ti.com
SBAS340A – JANUARY 2005 – REVISED APRIL 2005
APPLICATION INFORMATION
The DAC8803, a 2-quadrant multiplying DAC, can be used to generate a unipolar output. The polarity of the
full-scale output IOUT is the inverse of the input reference voltage at VREF.
Some applications require full 4-quadrant multiplying capabilities or bipolar output swing. An additional external
op amp A2 is added as a summing amp. In this circuit the first and second amps (A1 and A2) provide a gain of
2X that widens the output span to 20 V. A 4-quadrant multiplying circuit is implemented by using a 10-V offset of
the reference voltage to bias A2. According to the following circuit transfer equation ( Equation 2), input data (D)
from code 0 to full scale produces output voltages of VOUT = -10 V to VOUT = 10 V.
V OUT (D32, 768 1) VREF
(2)
10 k
10 k
10 V
5 k
A2
VREF
VOUT
−10 V < VOUT< +10 V
VREFX
VFBX
One Channel
DAC8803
VSS
IOUTX
A1
AGNDFA AGNDX
Digital interface connections omitted for clarity.
Figure 59. Four-Quadrant Multiplying Application Circuit
Cross-Reference
The DAC8803 has an industry-standard pinout. Table 4 provides the cross-reference information.
Table 4. Cross-Reference
PRODUCT
INL (LSB)
DNL (LSB)
SPECIFIED
TEMPERATURE
RANGE
DAC8803IDB
±1
±1
-40°C to +85°C
PACKAGE
DESCRIPTION
PACKAGE
OPTION
CROSSREFERENCE PART
28-Lead MicroSOIC
SSOP-28
AD5554BRS
27
PRODUCT PREVIEW
VDD
PACKAGE OPTION ADDENDUM
www.ti.com
13-Apr-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
DAC8803IDBR
PREVIEW
SSOP
DB
28
2500
TBD
Call TI
Call TI
DAC8803IDBT
PREVIEW
SSOP
DB
28
250
TBD
Call TI
Call TI
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated