HO1079 • • • SAW Frequency Stabilization Fundamental-Mode Oscillation at 1090.0 MHz Ideal for Air Traffic Control Applications 1090.0 MHz SAW Oscillator The frequency of this oscillator is stabilized by surface-acoustic-wave (SAW) technology. This results in excellent performance from a compact, rugged, oscillator operating at the fundamental frequency of 1090.0 MHz. The highly-reliable HO1079 is designed for use in air traffic control (ATC) radar transponders in commercial aviation. It is a commercial version of the HO1081 oscillator. Absolute Maximum Ratings Rating Value DC Supply Voltage 0 to +13 Ambient Temperature Units VDC Powered -40 to +85 Storage -40 to -100 Dip 16-8 Case °C Electrical Characteristics Characteristic Operating Frequency AbsoluteFrequency Tolerance from 310.0 MHz RF Output Power Discrete Spurious Sym fO PO DC Power Supply Typical 1090 1089.750 3, 6 +8 ZO 3 Operating Load VSWR GL 3, 5 VCC 3, 6 Operating Current MHz -35 <-100 -100 2, 3, 4 Nominal Impedance Operating Ambient Temperature Units 1090.250 -25 2, 3, 4 Nonharmonic 1 kHz Offset Operating Voltage Maximum +10 Second Harmonics 10 kHz Offset RF Impedance 1, 7 Minimum DfO Third and Higher Harmonics SSB Phase Noise Notes 3, 6 Lid Symbolization (YY=Year, WW=Week) kHz +14 -20 dBm -30 -80 dBc -90 -120 dBc/Hz -110 50 11.75 ICC TA ±250 W 12.0 1.5:1 12.25 VDC 35 40 mA +85 °C -40 RFM HO1079 YYWW BLOCK DIAGRAM CAUTION: Electrostatic Sensitive Device. Observe precautions for handling, COCOM CAUTION: Approval by the U.S. Department of Commerce is required prior to export of this device. V CC Notes: 1. 2. 3. 4. 5. 6. 7. One or more of the following United States patents apply: 4,616,197; 4,610,681; and 4,761,616. Unless noted otherwise, all specifications are listed at TA = +25°C ±2°C, VCC = nominal voltage ±0.01 VDC, and load impedance = 50 Ω with VSWR ≤ 1.5:1. The design, manufacturing process, and specifications of this device are subject to change without notice. Applies to oscillator only and not to sidebands caused by external electrical or mechanical sources. (Dedicated external voltage regulation with low-frequency filtering for the DC power supply and proper circuit board layout are recommended for optimum spectral purity.) For specified maximum operating load VSWR (any angle) at FO. (No instability or damage will occur for any passive load impedance.) For any combination of VCC and TA within the specified operating ranges. Applies for any combination of Note 5 and 6 conditions. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. RF OUTPUT SAW Oscillator Buffer Amplifier ELECTRICAL CONNECTIONS VCC Ground 1 Ground 2 15 Ground Top View Ground 7 Output 8 E-mail: [email protected] http://www.rfm.com HO1079-111201 10 Ground 9 Ground Page 1 of 2 1090.0 MHz DIP16-8 SAW Oscillator Metal Dual-Inline Package with 8 leads in a 16-lead DIP configuration mm Inches Dimension Top View MIN MAX MIN MAX A — 25.02 — 0.985 B — 12.83 — 0.505 C — 6.35 — 0.250 D 0.40 0.51 0.016 0.020 E 0.64 Nominal 0.025 Nominal F 7.62 Nominal 0.300 Nominal G 2.54 Nominal 0.100 Nominal H 17.78 Nominal 0.700 Nominal K 3,39 6.73 0.130 0.265 L 1.30 — 0.051 — M — 11.18 — 0.440 N — 22.60 — 0.890 R 1.75 2.26 0.069 0.089 Bottom View C B M K F (4 Places) R L (3 Places) 8 7 A 9 10 H N 2 1 D Pin 1 Mark (Optional) E 15 16 G (4 Places) (8 Places) RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com HO1079-111201 Page 2 of 2