Series AMEGR25-KZ-C1 700mA | AC-DC LED driver FEATURES: • • • • AC-DC Constant Current LED Driver Power Factor Correction Short circuit protection RoHS compliant • • • • Waterproof IP67 Over current protection Over voltage protection Low output ripple Models Single output Model Max Output Power (W) * Output Voltage Range (V) AMEGR25-3670KZ-C1 26.3 25-36 Output Current (mA) 700 ±30 Input Voltage (VAC/Hz) Efficiency (%) 175-250/47-63 82 * Exceeding the maximum output power will permanently damage the converter NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Conditions Typical 175V 230V 230V 175V 230V 175-250 10 20 0.25 0.14 0.12 0.8 Voltage range Inrush current <2ms Leakage current AC current No-load consumption External fuse Power Factor Maximum Units VAC A mA A W 250V/2.5A 0.9 Output Specifications Parameters Conditions Current accuracy Line regulation Load regulation Ripple & Noise Hold-up time (min) Typical ±5 ±5 ±10 100 4 Maximum Units 8 % % % mV p-p ms Maximum Units Isolation Specifications Parameters Tested I/O voltage Input FG Isolation resistance Conditions Typical 5mA/60Sec 3000 1500 >50 Conditions Typical VAC VAC MΩ General Specifications Parameters Switching frequency Over current protection Over voltage protection Short circuit protection Short Circuit restart Operating temperature * Maximum case temperature www.aimtec.com F 052.1e R1.D Maximum 100 115 Zener Diode clamp Continuous Auto-Recovery -30 to +55 KHz % o 85 Tel: +1 514 620 2722 1 of 2 Units o C C Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMEGR25-KZ-C1 700mA | AC-DC LED driver General Specifications (continued) Parameters Conditions Storage temperature Temperature coefficient Cooling Humidity Case material Weight Dimensions (L X H X W) MTBF Typical Maximum Units o -40 to +80 0.05 Free Air Convection C % / oC 95 % RH Aluminum 320 8.66 x 1.26 x 0.87 inches 220.00 x 32.00 x 22.00 mm 50,000 hrs (MIL-HDBK-217 F at +25 oC) g * NOTE: Converters do not have Over Temperature Protection and will be damaged if their maximum case temperature is exceeded. Safety Specifications Parameters Agency approvals Standards CE GB195110.1-2004/IEC61347-1:2003, EN55015, EN61000, EN61547 Dimensions NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 052.1e R1.D Tel: +1 514 620 2722 2 of 2 Toll free: + 1 888 9 AIMTEC (924 6832) North America only