CML Semiconductor Products SPM and Security Subsystem FX651 D/651/4 September 1997 1.0 Features • Provisional Information Two Integrated Telecoms Functions: • Low Power (3.3V) Requirement • • 12kHz SPM Detector Half Duplex 18kHz Modem • Component Adjustable Input Sensitivity • Compact 16-pin Small Outline (SOIC) Package • Meets European 12kHz SPM Frequency Specifications • Card Operated Telephone Installations • Worldwide Pay-Phone Applications VBIAS 1.1 Brief Description The FX651 integrated circuit combines 12kHz Subscriber Private Metering (SPM) detection with 18kHz tone processing for anti-fraud purposes within a telephone system. This compact, low power device is suitable for battery or line powered systems. Under simple logic or µProcessor control it will: Decode 12kHz SPM pulses in the presence of high level voice and 18kHz signalling, and provide a logic output. Transmit an NRZ modulated 18kHz security tone to line. Decode an incoming modulated 18kHz security tone in the presence of high level voice and 12 kHz SPM tones, and provide a logic output. Employing high accuracy switched capacitor filters, the FX651 is protected from crosstalk and false decoding. 1997 Consumer Microcircuits Limited SPM and Security Subsystem FX651 CONTENTS Section Page 1.0 Features .......................................................................................................... 1 1.1 Brief Description ............................................................................................ 1 1.2 Block Diagram ................................................................................................ 3 1.3 Signal List ....................................................................................................... 4 1.4 External Components .................................................................................... 6 1.5 General Description ....................................................................................... 7 1.5.1 Overall Function............................................................................. 7 1.5.2 Description of Blocks .................................................................... 7 1.6 Application Notes........................................................................................... 9 1.6.1 Device Sensitivity........................................................................... 9 1.6.2 Alias Responses ............................................................................ 9 1.7 Performance Specification.......................................................................... 10 1.7.1 Electrical Performance ................................................................ 10 1.7.2 Packaging ..................................................................................... 14 1997 Consumer Microcircuits Limited 2 D/651/4 SPM and Security Subsystem 1.2 FX651 Block Diagram VBIAS Figure 1 Block Diagram 1997 Consumer Microcircuits Limited 3 D/651/4 SPM and Security Subsystem 1.3 FX651 Signal List Package D4 Pin No. Signal Name Description Type 1 XTAL I/P The input to the on-chip oscillator inverter. 2 XTALN O/P The inverted output of the on-chip oscillator. To use, a crystal of frequency 3.579545MHz should be connected between these two pins. No other external components are necessary. 4 CLKIN I/P A logic input which may be used when an external clock signal is available in place of a crystal. The external 3.579545MHz signal is applied to this pin and XTAL is tied to VDD. When not used, this pin should be tied to VDD. 5 RX/TXN I/P A logic input which controls the operating mode of the device. In Rx, the device detects the presence of 12kHz and 18kHz tones. In Tx, the 18kHz detect function is disabled and 18kHz is transmitted from the TXOP pin modulated ON OFF by the NRZ Data pin. 6 NRZ DATA I/P A logic input used in Tx mode to ASK modulate the TXOP pin. A logic high corresponds to no tone and logic low corresponds to 18kHz. 7 TXOP O/P The Tx mode output. It is ASK modulated by the NRZ data input pin. It transmits 18kHz or no tone depending upon the state of the NRZ data input pin. This pin goes to a high impedance state when in Rx mode. 8 VSS 9 VBIAS 1997 Consumer Microcircuits Limited POWER O/P Negative supply rail. A bias line for the internal circuitry, held at ½ VDD. It also forms the analogue ground for the input differential amplifier. This pin must be decoupled by a capacitor mounted close to the device pins (see Figure 1). 4 D/651/4 SPM and Security Subsystem FX651 Package D4 Pin No. Signal Name Description Type 10 AMPOP O/P The input amplifier's output. External components are used in conjunction with the amplifier to couple the line signal into the device. Both inputs are available to allow a differential configuration because a two wire input is assumed. 11 NEGIP I/P The input amplifier's inverting input. 12 POSIP I/P The input amplifier's non inverting input. 13 DETECT 18kHz O/P The logic output of the 18kHz channel which is active in Rx mode. Logic "0" signals the presence on the line of 18kHz tone within specified frequency and amplitude limits. 14 DETECT 12kHz O/P The logic output of the 12kHz channel. It goes to logic "0" when a 12kHz tone within specified frequency and amplitude limits has been detected for a minimum length of time. 16 VDD 3, 15 N/C Notes: I/P = O/P = POWER The positive supply rail. Levels and voltages are dependent upon this supply. This pin should be decoupled to VSS by a capacitor (see Figure 1). No internal connection: leave open circuit. Input Output 1997 Consumer Microcircuits Limited 5 D/651/4 SPM and Security Subsystem 1.4 FX651 External Components Component C1, C2 R1, R3 R2, R4 C3, C4 R5 C5 3.3V 33pF ±10% 1.1MΩ ±1% 270kΩ ±1% 5.0V 68pF ±10% 1.0MΩ ±1% 330kΩ ±1% 0.1µF ±20% 51kΩ ±1% 100pF ±10% Notes 1. The device's sensitivity is approximately proportional to its power supply (VDD) voltage. The input gain must compensate for this and also prevent the input circuitry saturating. It is recommended that the amplifier components (R1 to R4, C1 and C2) are used to set the gain between -10dB (if VDD is 5.0V) and -13dB (if VDD is 3.3V). Figure 2 Recommended External Components (D4) 1997 Consumer Microcircuits Limited 6 D/651/4 SPM and Security Subsystem FX651 1.5 General Description 1.5.1 Overall Function The FX651 is a dual channel tone detector for use in the French Payphone system where 12kHz SPM and 18kHz security tones are used. SPM (12kHz) Detector The SPM detector channel responds to a low level (50mV) 12kHz tone in the presence of a large security tone (16kHz - 20kHz) and speech. The device responds after a period of continuous valid tone and so recognises a valid SPM toneburst (minimum transmission duration, 75ms). This function is permanently enabled. Security Tone (18kHz) Detector (Rx Mode Only) This demodulates the 18kHz ASK signal in the presence of the SPM signalling. Security Tone Transmission (Tx Mode Only) An 18kHz tone modulated ON - OFF by the NRZ data pin. A logic low gates the signal ON so that 18kHz is transmitted. A logic high gates the signal OFF so that no tone appears at the TXOP pin. 1.5.2 Description of Blocks (See Figure 1) Input Amplifier This amplifier is connected as a differential amplifier and is used to couple the signal into the device. It also attenuates the combined speech, SPM tone and security tone to prevent its output saturating. Its signal gain should be -10dB at 5.0V supply and -13dB at 3.3V. (See Figure 2 for recommended component values) Sample and Hold (12kHz Channel) This samples the input signal at 17.898kHz and creates images of the incoming frequencies. The 12kHz SPM is translated to 5.898kHz and the security tone is translated to between 978Hz and 1182Hz. This simplifies the subsequent signal processing. Filtering and Frequency Detection (12kHz Channel) The output of the sample and hold circuit is passed to filter HPF1. This is a switched capacitor high pass filter which amplifies the frequency shifted SPM tone (about 5.9kHz) but rejects the frequency shifted security tone (about 1kHz). The filter also rejects any speech signals present. The filter output is passed to the level detect and frequency measurement circuitry which determines the presence or absence of a valid SPM signal on the line. A valid signal sends the "DETECT 12kHz" pin to logic low. Sample and Hold (18kHz Channel) This samples the input signal at 71.592kHz. It is synchronised with the following high pass filter, which is a switched capacitor circuit with the same sampling rate. The sample and hold circuit stores the value of the input waveform value between sampling instants so that it is a suitable input for the filter. Without the sample and hold circuit, speech or SPM tone components which are large compared with the security tone would interfere with the level discrimination at the filter output. 1997 Consumer Microcircuits Limited 7 D/651/4 SPM and Security Subsystem FX651 Filtering and Frequency Detection (18kHz Channel) The output of the sample and hold circuit is passed to filter HPF2. This is a switched capacitor high pass filter which amplifies the security tone (about 16.92kHz - 19.08kHz) but rejects the SPM tone. The filter output signal is passed to the level detect and frequency measurement circuitry which determines the presence or absence of a valid security tone on the line. A valid signal sends the "DETECT 18kHz" pin to logic low. Clock Oscillator and Dividers These circuits generate the internal clocks by division of the oscillator reference frequency. The crystal is connected as shown in Figure 2 without any need for other external components. When a crystal is used, the CLKIN pin should be left open circuit. Alternatively, when a frequency of 3.579545MHz is externally available, the use of a crystal is unnecessary. The external frequency is applied to the CLKIN pin. In this case, the XTAL pin should be tied to VDD. In Tx, the dividers also generate a pulse train, frequency 18kHz, which is passed to the Tx circuitry (Gate ON - OFF and Band Pass Filter) for digital modulation and filtering. Gate ON-OFF (Tx Only) This circuit is a digital block. It performs ON - OFF modulation of the 18kHz pulse train generated from the crystal frequency by the digital dividers. It is controlled by the NRZ DATA pin and is used to encode NRZ data packets as pulsed 18kHz (ASK data). The modulated digital signal is passed to the Tx filter for wave shaping. Band Pass Filter (Tx Only) This is a 4th order band pass filter with centre frequency 18kHz. It shapes the modulated digital pulse train from the previous block into a low distortion pulsed sinusoidal waveform. The resulting signal is the system acknowledgement security tone. It is transmitted by the subscriber equipment, via the telephone link, to the local exchange. 1997 Consumer Microcircuits Limited 8 D/651/4 SPM and Security Subsystem FX651 1.6 Application Notes 1.6.1 Device Sensitivity versus VDD - Input Amplifier Gain The device sensitivity is proportional to VDD because internal voltage references are derived from the power supply. This means that the input amplifier signal gain should be adjusted to compensate. Figure 2 shows components recommended for 5.0V and 3.3V operation. 1.6.2 Alias Responses - False Decodes The FX651 is designed to work in telephone systems where certain ranges of input frequencies are expected and other ranges are not. The 12kHz SPM channel works in the presence of speech and a tone in the range 16kHz - 20kHz. The security tone detector functions in the presence of an interfering tone in the range 11kHz - 13kHz. A significant tone at other frequencies may interfere with correct decoding of valid transmissions and should be avoided. A small range of input frequencies could cause false decoding when no valid tone has been received. This is because of the frequency shifting property of the SPM channel and the SWC filters (i.e sampled data filters) in both channels. The alias frequencies which should be avoided are: 12kHz Channel Input frequencies in the ranges: 5.708kHz - 6.078kHz 41.504kHz - 41.874kHz 23.606kHz - 23.976kHz 47.986kHz - 47.616kHz 29.718kHz - 30.088kHz 59.402kHz - 59.772kHz In general, decodes may be caused by tones in the ranges: (( n × 17.898) ± (5.708 − 6.078))kHz where n = 0, 1, 2, 3...... Taking n = 1 and the minus sign represents valid SPM inputs in the range 11.82kHz 12.18KHz. The other inputs represent false decodes. The response time and level sensitivity for a false decode is the same as that for a valid decode, e.g. 42ms - 45ms of 5708Hz at 50mV could cause a false decode at the "DETECT 12kHz" pin. 18kHz Channel Input frequencies in the ranges: 52.511kHz - 54.671kHz 88.511kHz - 90.671kHz In general, decodes could be caused by any tone in the ranges: (( n × 71.591) ± (16.92 − 19.08))kHz where n = 0, 1, 2, 3...... The case where n = 0 and the addition sign is used represents valid security tone inputs. The other cases represent false decodes. The response time and level sensitivity for a false decode is the same as that for a valid decode, e.g. 5.8ms of 52.511kHz at 40mV could cause a false response at the "DETECT 18kHz" pin. 1997 Consumer Microcircuits Limited 9 D/651/4 SPM and Security Subsystem 1.7 Performance Specification 1.7.1 Electrical Performance FX651 Absolute Maximum Ratings Exceeding these maximum ratings can result in damage to the device. Min. -0.3 -0.3 -30 -20 -55 -40 Supply (VDD - VSS) Voltage on any pin (wrt VSS) Current into or out of VDD and VSS pins Current into or out of any other pin Storage Temperature Operating Temperature Total Allowable Power Dissipation at Tamb = 25°C Derating ... Max. 7.0 VDD + 0.3 +30 +20 +125 +85 800 13 Units V V mA mA °C °C mW mW/°C Max. 5.5 +85 3.580082 Units V °C MHz Operating Limits Correct operation of the device outside these limits is not implied. Min. 3.0 -40 3.579008 Supply (VDD - VSS) Operating Temperature Xtal Frequency Operating Characteristics For the following conditions unless otherwise specified: Xtal Frequency = 3.579545MHz, Noise and Distortion Measured in 50kHz Bandwidth VDD = 3.3V to 5.5V, Tamb = -40°C to 85°C. Notes DC Parameters VDD IDD IDD Typ. Max. Units 2.5 1.0 5.5 4.0 2.0 V mA mA 3.3 1 2 Logic "1" Input Level Logic "0" Input Level Logic "1" Output Level at IOH = -120µA Logic "1" Output Level at IOL = 360µA Notes: Min. 1, 3 1, 3 1 1 3.5 1.5 4.6 0.4 1. At VDD = 5.0V only, IDD specification does not include any current drawn from the device pins by external circuitry. 2. At VDD = 3.3V only, IDD specification does not include any current drawn from the device pins by external circuitry. 3. CLKIN input signal may be sinusoidal. 1997 Consumer Microcircuits Limited 10 V V V V D/651/4 SPM and Security Subsystem FX651 Operating Characteristics (continued) Notes AC Parameters Tx Output Tx O/P Impedance (Tx mode) Tx O/P Impedance (Rx mode) Output Frequency Output Distortion Signal Level Signal Level Response/De-response Times Rise/Fall Times 4 4 5 5, 6 5, 7 8 9 300 17.82 3.0 2.0 Typ. Max. Units 1.0 500 2.5 kΩ kΩ kHz % Vp-p Vp-p µs ms 3.4 2.2 18.18 2 3.7 2.4 100 5 10 Rx Input Rx I/P Impedance Rx I/P Amp Voltage Gain 10.0 MΩ V/V 500 11 12kHz (SPM) Channel Performance 12 12 12 12 With Interfering Speech & Security Tone 12kHz Input Signal Level 12kHz Decode Min Signal Level 12kHz No Decode Max Signal Level Response Delay De-response Delay Detect Bandwidth Not Detect Frequencies (below 12kHz) Not Detect Frequencies (above 12kHz) 12, 13 12, 13 12 12 12 800 50 mV mV mV 50 50 12.18 11.52 ms ms kHz kHz kHz 1.2 40 V mV mV 8 19.08 16.25 ms kHz kHz kHz 25 40 40 11.82 12.48 14 18kHz (Security Tone) Channel Performance With Interfering Speech & SPM Tone 18kHz Input Signal Level 18kHz Decode Min Signal Level 18kHz No Decode Max Signal Level 15 15 15 15 Response/De-response Times Detect Bandwidth Not Detect Frequencies (below 18kHz) Not Detect Frequencies (above 18kHz) 15, 16 15 15 15 1997 Consumer Microcircuits Limited Min. 11 10 16.92 19.75 D/651/4 SPM and Security Subsystem Notes: FX651 4. Small signal impedance. 5. At output of smoothing network. 6. VDD = 5.0V. 7. VDD = 3.3V. 8. The time between a logic "1 - 0" transition at NRZ data input and the tone at TXOP reaching 10% of its full value or between a "0 - 1" transition at NRZ data input and the tone falling to 90% of its full value. 9. The time for the 18kHz tone at TXOP to rise from 10% to 90% or to fall from 90% to 10% of its full value. 10. Input amplifier signal gain set to -10dB for VDD = 5.0V, -13dB for VDD = 3.3V. 11. Maximum 10% distortion for incoming SPM tone, not including interfering speech or security tone (16kHz - 20kHz). Minimum SNR 22dB for incoming SPM tone. 12. Signal levels at the line side of the input capacitor. 12kHz channel performance specified in the presence of the following interfering signals: (a) A 1.2V tone in the frequency range 16kHz - 20kHz. (b) An ordinary speech signal containing frequencies in the range 300Hz - 3400Hz of maximum instantaneous amplitude 8.0Vpk-pk. 13. The device responds after 40-50ms of continuous valid tone and de-responds after: a 40-50ms period of no-tone, tones less than 25mV or an out of band tone. 14. Maximum 10% distortion for incoming security tone, not including interfering SPM tone (11kHz - 13kHz). Minimum 20dB SNR for incoming security tone. 15. Signal level specified at the line side, i.e. before the input capacitor. Performance specified in the presence of an interfering 800mV tone in the frequency range 11kHz 13kHz. 16. The device responds after 8ms of continuous valid tone and de-responds after: a 8ms period of no-tone, tone of 10mV or less, or an out of band tone. 1997 Consumer Microcircuits Limited 12 D/651/4 SPM and Security Subsystem FX651 System Timings (See also Table 1 on next page) (a) SPM (12kHz) channel. Toneburst and tonegaps less than the response and de-response are ignored. delays (b) Security tone (18kHz) channel. The response and de-response times are short to enable the device to recognise the short ON-OFF bursts (20ms each). (c) Transmit Mode. TXOP is modulated by the NRZ DATA pin. An 18kHz toneburst represents logic "0" and "no tone" represents logic "1". Data packets with symbol periods greater than or equal to 6ms can be transmitted. Figure 3 System Timing Diagrams 1997 Consumer Microcircuits Limited 13 D/651/4 SPM and Security Subsystem Rx FX651 Min Max Unit 40 40 50 50 ms ms 12KHz Response Delay De-response Delay 18KHz Response Time De-response Time 8 8 ms ms Transmit "0" Time Transmit "1" Time 5.1 5.1 ms ms Tx * Table 1 System Timings * Note: Tx Transmit Times include both Response/De-response Times and Rise/Fall Times. 1.7.2 Packaging The FX651 is available in the 16-pin SOIC package detailed below: D IM . A B C E F H J K K1 L P T W X Y M IN . T Y P. M AX. 0 .3 95 (1 0 .0 3) 0 .41 3 (1 0 .49 ) 0 .2 99 (7 .5 9) 0 .29 1 (7 .3 9) 0 .0 93 (2 .3 6 ) 0.1 0 5 (2 .67 ) 0.39 4 (1 0.0 1 ) 0.41 9 (1 0.64 ) 0 .3 66 (9 .2 9 ) 0 .00 4 (0 .1 0) 0 .0 1 2 (0.3 0 ) 0 .0 19 (0 .4 8 ) 0 .01 3 (0 .3 3) 0.04 1 (1 .04 ) 0 .0 41 (1 .0 4 ) 0.05 0 (1 .2 7) 0.0 1 6 (0 .41 ) 0.0 5 0 (1 .27 ) 0.01 2 (0 .3 0) 0 .0 0 9 (0.2 3 ) 45° 0° 8° 7° N O T E : A ll d im e nsio n s in in ch e s (m m .) A n g les in d e gre es Figure 4 SOIC Mechanical Outline: Order as part no. FX651D4 1997 Consumer Microcircuits Limited 14 D/651/4 SPM and Security Subsystem FX651 Handling precautions: This product includes input protection, however, precautions should be taken to prevent device damage from electro-static discharge. CML does not assume any responsibility for the use of any circuitry described. No IPR or circuit patent licences are implied. CML reserves the right at any time without notice to change the said circuitry and this product specification. CML has a policy of testing every product shipped using calibrated test equipment to ensure compliance with this product specification. Specific testing of all circuit parameters is not necessarily performed. CONSUMER MICROCIRCUITS LIMITED 1 WHEATON ROAD WITHAM - ESSEX CM8 3TD - ENGLAND Telephone: Telefax: e-mail: +44 1376 513833 +44 1376 518247 [email protected] http://www.cmlmicro.co.uk CML Microcircuits COMMUNICATION SEMICONDUCTORS CML Product Data In the process of creating a more global image, the three standard product semiconductor companies of CML Microsystems Plc (Consumer Microcircuits Limited (UK), MX-COM, Inc (USA) and CML Microcircuits (Singapore) Pte Ltd) have undergone name changes and, whilst maintaining their separate new names (CML Microcircuits (UK) Ltd, CML Microcircuits (USA) Inc and CML Microcircuits (Singapore) Pte Ltd), now operate under the single title CML Microcircuits. These companies are all 100% owned operating companies of the CML Microsystems Plc Group and these changes are purely changes of name and do not change any underlying legal entities and hence will have no effect on any agreements or contacts currently in force. CML Microcircuits Product Prefix Codes Until the latter part of 1996, the differentiator between products manufactured and sold from MXCOM, Inc. and Consumer Microcircuits Limited were denoted by the prefixes MX and FX respectively. These products use the same silicon etc. and today still carry the same prefixes. In the latter part of 1996, both companies adopted the common prefix: CMX. This notification is relevant product information to which it is attached. Company contact information is as below: CML Microcircuits (UK)Ltd CML Microcircuits (USA) Inc. CML Microcircuits (Singapore)PteLtd COMMUNICATION SEMICONDUCTORS COMMUNICATION SEMICONDUCTORS COMMUNICATION SEMICONDUCTORS Oval Park, Langford, Maldon, Essex, CM9 6WG, England Tel: +44 (0)1621 875500 Fax: +44 (0)1621 875600 [email protected] www.cmlmicro.com 4800 Bethania Station Road, Winston-Salem, NC 27105, USA Tel: +1 336 744 5050, 0800 638 5577 Fax: +1 336 744 5054 [email protected] www.cmlmicro.com No 2 Kallang Pudding Road, 09-05/ 06 Mactech Industrial Building, Singapore 349307 Tel: +65 7450426 Fax: +65 7452917 [email protected] www.cmlmicro.com D/CML (D)/1 February 2002