FTDI C232HM-EDHSL-0

Future Technology Devices International Ltd
C232HM
USB 2.0 Hi-Speed to MPSSE Cable
Datasheet
Document Reference No.: FT_000401
Version 1.0
Issue Date: 2011-07-21
Future Technology Devices International Limited (FTDI)
Unit 1, 2 Seaward Place, Glasgow G41 1HH, United Kingdom
Tel.: +44 (0) 141 429 2777 Fax: + 44 (0) 141 429 2758
E-Mail (Support): [email protected] Web: http://www.ftdichip.com
Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to
defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such
use.
© Copyright 2011 Future Technology Devices International Ltd
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
1
Description
The USB 2.0 Hi-Speed to MPSSE cable contains a small internal electronic circuit board, utilising the
FTDI FT232H, which is encapsulated into the USB connector end of the cable, this handles all the USB
signalling and protocols. The cable provides a fast, simple way to connect devices with 3.3 Volt digital
interfaces to USB. For full details of the IC, consult the FT232H datasheet, this is available from
DS_FT232H.
The integrated FT232H device incorporates a command processor called the Multi-Protocol Synchronous
Serial Engine (MPSSE). The purpose of the MPSSE command processor is to communicate with devices
which use synchronous protocols (such as JTAG, SPI or I2C) in an efficient manner. Full details are
available in the MPSSE application note - AN_108.
The cable is terminated by ten individual wires with single pole connectors which can be interfaced to a
male header. Cable signals are compliant with CMOS logic at 3.3 volts.
The FT232H is a single channel USB 2.0 Hi-Speed (480Mb/s) to UART/FIFO IC. It can be configured in a
variety of industry standard serial or parallel interfaces, such as MPSSE - JTAG, SPI, I2C.
The C232HM MPSSE cable is easily configured into each interface e.g. JTAG, SPI, I2C via the application
software.
The cable is powered from a USB host port and is USB 2.0 Hi-Speed compatible. The cable is 0.5m long
and supports a data transfer up to 30Mbps in MPSSE mode.
The C232HM MPSSE cable requires USB device drivers, available free from http://www.ftdichip.com. The
D2XX driver is used with application software to directly access the FT232H in the cable though a DLL.
This is illustrated in the Figure 1-1
The C232HM MPSSE cable uses the FTDI’s FT232H USB to serial IC device.
Connector
C232HM
D2XX
DLL
API
USB
10 Female pin
headers
Software application access to USB via D2XX
Figure 1-1 Using the C232HM MPSSE Cable
Copyright © 2011 Future Technology Devices International Limited
1
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
1.1 Available Cables and Part Numbers
The following Table 1.1 gives details of the available C232HM MPSSE cables.
Part Number
Description
End Connector
Cable details
USB to MPSSE cable with +3.3V
digital level signals. Maximum
C232HM-DDHSL-0
output of 200mA @ 3.3VDC on
VCC
10 core, UL2464 24 AWG,
Single pole,
diam=6.5mm
receptacle x 10
(see Note 1)
USB to MPSSE cable with +3.3V
digital level signals. Maximum
C232HM-EDHSL-0
output of 200mA @ 5.0VDC on
VCC
10 core, UL2464 24 AWG,
Single pole,
diam=6.5mm
receptacle x 10
(see Note 2)
Table 1.1 C232HM MPSSE Cable Descriptions and Part Numbers
Note 1: The VCC power output signal (RED wire) is 3.3V. The source of 3.3V is the onboard regulator output, which
is switched onto the power output signal.
Note 2: The VCC power output signal (RED wire) is 5.0V. The source of 5.0V is the USB VBUS input, which is
switched onto the power output signal.
FTDI supports customised end connector designs. For more information, please contact your local FTDI
sales office (see end of datasheet for contact details).
1.2 Certifications
The FTDI C232HM MPSSE cables are fully RoHS, FCC and CE compliant.
Copyright © 2011 Future Technology Devices International Limited
2
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
Table of Contents
1
2
3
Description ..................................................................................... 1
1.1
Available Cables and Part Numbers ............................................................... 2
1.2
Certifications ................................................................................................. 2
Typical Applications ........................................................................ 4
2.1
Driver Support .............................................................................................. 4
2.2
Features ........................................................................................................ 5
C232HM MPSSE Cable connection and Mechanical Details .............. 6
3.1
C232HM MPSSE Cable Signal Descriptions .................................................... 7
3.2
C232HM MPSSE Cable Signal Descriptions .................................................... 8
3.3
C232HM MPSSE Cable Electrical Parameters ................................................. 9
3.3.1
C232HM-DDHSL-0
Electrical Parameters ..................................................... 9
3.3.2
C232HM-EDHSL-0 Electrical Parameters ....................................................... 9
3.3.1
C232HM-DDHSL-0 and C232HM-EDHSL-0 I/O Characteristics ........................10
4
Cable PCB Circuit Schematic ......................................................... 11
5
Contact Information ..................................................................... 13
Appendix A - Cable EEPROM Configuration ......................................... 15
Appendix B - List of Figures and Tables ............................................. 16
Appendix C – Revision History ........................................................... 17
Copyright © 2011 Future Technology Devices International Limited
3
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
2
Typical Applications
USB to JTAG interfaces
Rapid USB integration into existing
USB to SPI interfaces
electronic systems
2
USB to I C interfaces
Prototyping platform for USB interface on
Interfacing MCU / PLD / FPGA based
new systems
designs to USB
USB Instrumentation
USB Audio and Low Bandwidth Video data
transfer
2.1 Driver Support
Royalty free D2XX Direct Drivers
(USB Drivers + DLL S/W Interface)
Windows 98, 98SE, ME, 2000, Server 2003, XP
and Server 2008
Windows XP and XP 64-bit
Windows 7 and Windows 7 64-bit
Windows Vista and Vista 64-bit
Windows CE 4.2, 5.0 and 6.0
Linux 2.4.20 and greater
The drivers listed above are all available to download for free from http://www.ftdichip.com. Various
Third-Party Drivers are also available for various other operating systems - see
http://www.ftdichip.com/Support/Links.htm for details.
Copyright © 2011 Future Technology Devices International Limited
4
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
2.2 Features
Based on the Single chip USB Hi-Speed
FT232H device
USB 2.0 Hi-Speed (480Mbits/Second) and
Full Speed (12Mbits/Second) compatible
Entire USB protocol handled on the chip –
No USB-specific firmware programming
required
USB Type A connector for direct connection
to a host or hub
Transmit and receive LED drive signals
Adjustable receive buffer timeout
Support for USB suspend and resume
Low operating and USB suspend current
Low USB bandwidth consumption
UHCI / OHCI / EHCI host controller
compatible
USB bus powered
-40°C to +85°C operating temperature
range
Fully assisted hardware or X-On / X-Off
software handshaking
Cable length is 0.5m (19.7 inch)
Synchronous Serial (MPSSE) data rates of
up to 30Mbps on JTAG, SPI and I2C
1kByte receive and transmit buffers for
high data throughput
Custom versions also available (subject to
Minimum Order Quantity (MOQ))
FTDI’s royalty-free D2XX drivers eliminate
the requirement for USB driver
development in most cases
Copyright © 2011 Future Technology Devices International Limited
5
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
3
C232HM MPSSE Cable connection and Mechanical Details
The following Figure 3-1 shows the cable signals and the wire colours for these signals on the C232HM
MPSSE cable.
VCC
1
1
2
TCK
2
TDI
3
3
TD0
4
4
TMS
5
GPIOL0
6
6
GPIOL1
7
7
GPIOL2
8
8
GPIOL3
GND
9
10
5
CABLE 0.5m
9
10
RED
ORANGE
YELLOW
GREEN
BROWN
GREY
PURPLE
WHITE
BLUE
BLACK
Figure 3-1 C232HM MPSSE Cable Connections (numbers refer to pad numbers on the PCB)
Copyright © 2011 Future Technology Devices International Limited
6
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
3.1 C232HM MPSSE Cable Signal Descriptions
42.5
16
Figure 3-2 C232HM MPSSE Cable Mechanical Details (dimensions in mm)
Copyright © 2011 Future Technology Devices International Limited
7
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
3.2 C232HM MPSSE Cable Signal Descriptions
Colour
Pin
Number
Name
Type
Description
Red
1
VCC
Output
Power Supply Output to target board.
Gray
6
GPIOL0
Input/Output
General Purpose input/output.
Purple
7
GPIOL1
Input/Output
General Purpose input/output.
White
8
GPIOL2
Input/Output
General Purpose input/output.
Blue
9
GPIOL3
Input/Output
General Purpose input/output.
Black
10
GND
GND
Device ground supply pin.
Table 3.1 Common Cable Signal Descriptions
Colour
Pin
Number
Name
Type
Description
Orange
2
TCK
Output
Test Interface Clock
Yellow
3
TDI
Input
Green
4
TDO
Output
Test Data Output
Brown
5
TMS
Output
Test Mode Select
Test Data Input
Table 3.2 MPSSE Option JTAG - Signal Descriptions
Colour
Pin
Number
Name
Type
Description
Orange
2
SK
Output
Serial Clock
Yellow
3
DO
Output
Serial data output
Green
4
DI
Input
Serial Data Input
Brown
5
CS
Output
Serial Chip Select
Table 3.3 MPSSE Option SPI - Signal Descriptions
Colour
Pin
Number
Orange
2
Yellow
3
Green
4
Name
Type
Description
SCL
Output
Serial Clock
SDA
Input/Output
Serial data signal shorted together to create
bidirectional data(both yellow and green wires need to
be shorted together)
Table 3.4 MPSSE Option I2C - Signal Descriptions
Copyright © 2011 Future Technology Devices International Limited
8
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
3.3 C232HM MPSSE Cable Electrical Parameters
3.3.1 C232HM-DDHSL-0
Parameter
Description
Electrical Parameters
Minimum
Typical
Maximum
Units
VCC
Output Power Voltage
3.2
3.3
3.6
V
IO
Output Power Current
-
-
200
mA
T
Operating Temperature
Range
-40
+85
Conditions
o
C
Table 3.5 C232HM-DDHSL-0 Operating Parameters
3.3.2 C232HM-EDHSL-0 Electrical Parameters
Parameter
VCC
IO
T
Description
Output Power Voltage
Supply Current
Operating Temperature
Range
Minimum
Typical
Maximum
Units
4.75
5
5.25
V
-
-
200
mA
-40
+85
Conditions
Must be less that 2.5mA
during suspend.
o
C
Table 3.6 C232HM-EDHSL-0 Power Supply Output Parameters
Copyright © 2011 Future Technology Devices International Limited
9
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
3.3.1 C232HM-DDHSL-0 and C232HM-EDHSL-0 I/O Characteristics
Parameter
Description
Minimum
Typical
Voh
Output Voltage High
2.40
3.14
Maximum
Units
Conditions
Ioh = +/-2mA
V
I/O Drive strength* = 4mA
3.20
V
3.22
V
3.22
V
I/O Drive strength* = 8mA
I/O Drive strength* =
12mA
I/O Drive strength* =
16mA
Iol = +/-2mA
Vol
Output Voltage Low
0.18
0.40
V
I/O Drive strength* = 4mA
Vil
Vih
Vt
Vt-
Vt+
Rpu
Rpd
Iin
Ioz
0.12
V
0.08
V
0.07
V
Input low Switching
-
Input High Switching
Threshold
Schmitt trigger negative
going threshold voltage
0.80
resistance
Input Leakage Current
Tri-state output leakage
current
16mA
-
V
LVTTL
1.50
V
LVTTL
-
V
1.60
2.00
V
40
75
190
KΩ
Vin = 0
40
75
190
KΩ
Vin =VCCIO
15
45
85
μA
Vin = 0
μA
Vin = 5.5V or 0
going threshold voltage
Input pull-down
I/O Drive strength* =
1.10
Schmitt trigger positive
Input pull-up resistance
12mA
LVTTL
2.00
Switching Threshold
I/O Drive strength* =
V
Threshold
0.80
I/O Drive strength* = 8mA
±10
Table 3.7 C232HD-DDHSP-0 and C232HD-EDHSP-0 I/O Pin Characteristics
* The I/O drive strength and slow slew-rate are configurable in the EEPROM.
The I/O pins are +3.3v cells, which are +5V tolerant
Copyright © 2011 Future Technology Devices International Limited
10
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
4
Cable PCB Circuit Schematic
The circuit schematics for the small internal electronic circuit board, utilising the FTDI FT232H, which is
encapsulated into the USB connector end of the cable, are shown in Figure 4.1 Circuit Schematic of
C232HM-DDHSL-0 and Figure 4.2 - Circuit Schematic of PCB - C232HM-EDHSL-0.
Customised versions of these cables are also available. Users interested in customised versions of these
cables should contact FTDI sales ([email protected]).
Figure 4.1 Circuit Schematic of C232HM-DDHSL-0
Copyright © 2011 Future Technology Devices International Limited
11
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
Figure 4.2 - Circuit Schematic of PCB - C232HM-EDHSL-0
Copyright © 2011 Future Technology Devices International Limited
12
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
5
Contact Information
Head Office – Glasgow, UK
Future Technology Devices International Limited
Unit 1, 2 Seaward Place,
Centurion Business Park
Glasgow, G41 1HH
United Kingdom
Tel: +44 (0) 141 429 2777
Fax: +44 (0) 141 429 2758
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
Web Site URL
Web Shop URL
[email protected]
[email protected]
[email protected]
http://www.ftdichip.com
http://www.ftdichip.com
Branch Office – Taipei, Taiwan
Future Technology Devices International Limited (Taiwan)
2F, No. 516, Sec. 1, NeiHu Road
Taipei 114
Taiwan , R.O.C.
Tel: +886 (0) 2 8797 1330
Fax: +886 (0) 2 8751 9737
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
Web Site URL
[email protected]
[email protected]
[email protected]
http://www.ftdichip.com
Branch Office – Hillsboro, Oregon, USA
Future Technology Devices International Limited (USA)
7235 NW Evergreen Parkway, Suite 600
Hillsboro, OR 97123-5803
USA
Tel: +1 (503) 547 0988
Fax: +1 (503) 547 0987
E-Mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
Web Site URL
[email protected]
[email protected]
[email protected]
http://www.ftdichip.com
Branch Office – ShangHai, China
Future Technology Devices International Limited (China)
Room 408, 317 Xianxia Road,
ChangNing District,
ShangHai, P.R. China
Tel: +86 (21) 62351596
Fax: +86 (21) 62351595
E-Mail (Sales)
E-mail (Support)
E-Mail (General Enquiries)
Web Site URL
[email protected]
[email protected]
[email protected]
http://www.ftdichip.com
Distributor and Sales Representatives
Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales
representative(s) in your country.
Copyright © 2011 Future Technology Devices International Limited
13
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future
Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety,
regulatory and system-level performance requirements. All application-related information in this document (including
application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has
taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability
for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or
safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from
any and all damages, claims, suits or expense resulting from such use. This document is subject to change without
notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document.
Neither the whole nor any part of the information contained in, or the product described in this document, may be
adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder.
Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH,
United Kingdom. Scotland Registered Company Number: SC136640.
Copyright © 2011 Future Technology Devices International Limited
14
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
Appendix A - Cable EEPROM Configuration
Each C232HM MPSSE cable is controlled by the FTDI FT232H IC. This FT232H device contains an EEPROM
which contains the USB configuration descriptors for that device. When the cable is plugged into a PC or
a USB reset is performed, the PC will read these descriptors. The default values stored into the internal
EEPROM are defined in the following table
Parameter
Value
USB Vendor ID (VID)
0403h
FTDI default VID (hex)
USB Product UD (PID)
6014h
FTDI default PID (hex)
Serial Number Enabled?
Notes
Yes
A unique serial number is generated and programmed into
Serial Number
See Note
Manufacturer Name
the EEPROM during device final test.
FTDI
Product description depends on the cable. The following
lists a the Product descriptions for each different cable.
Product Description
See note
C232HM-VSW3V3
C232HM-VSW5V0
Max Bus Power Current
Power Source
500mA
Includes power available from the cable plus power
required for the FT232H
Bus Powered
Device Type
FT232H
USB Version
0200
Returns USB 2.0 device description to the host.
Note: The device is a USB 2.0 Hi-Speed device (480Mb/s).
Remote Wake Up
Disabled
500uA suspend limit when in this state
High Current I/Os
Enabled
Enables the high drive level on the CBUS I/O pins.
Invert TXD
Disabled
Signal on this pin becomes TXD# if enable.
Invert RXD
Disabled
Signal on this pin becomes RXD# if enable.
Invert RTS#
Disabled
Signal on this pin becomes RTS if enable.
Invert CTS#
Disabled
Signal on this pin becomes CTS if enable.
Default Internal EEPROM Configuration
The internal EEPROM in the cable can be re-programmed over USB using the utility program FT_PROG.
Both can be downloaded from www.ftdichip.com.
Copyright © 2011 Future Technology Devices International Limited
15
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
Appendix B - List of Figures and Tables
List of Figures
Figure 1-1 Using the C232HM MPSSE Cable ................................................................ 1
Figure 4-1 C232HM MPSSE Cable Connections (numbers refer to pad numbers on the
PCB) ........................................................................................................................... 6
Figure 4-2 C232HM MPSSE Cable Mechanical Details (dimensions in mm) ................ 7
Figure 5.1 Circuit Schematic of C232HM-DDHSL-0.................................................... 11
Figure 5.2 - Circuit Schematic of PCB - C232HM-EDHSL-0 ........................................ 12
List of Tables
Table 1.1 C232HM MPSSE Cable Descriptions and Part Numbers ................................ 2
Table 4.1 Common Cable Signal Descriptions ............................................................. 8
Table 4.2 MPSSE Option JTAG - Signal Descriptions ................................................... 8
Table 4.3 MPSSE Option SPI - Signal Descriptions ...................................................... 8
Table 4.4 MPSSE Option I2C - Signal Descriptions ...................................................... 8
Table 4.2 C232HM-DDHSL-0 Operating Parameters .................................................. 9
Table 4.4 C232HM-EDHSL-0 Power Supply Output Parameters................................. 9
Table 4.3 C232HD-DDHSP-0 and C232HD-EDHSP-0 I/O Pin Characteristics ............. 10
Copyright © 2011 Future Technology Devices International Limited
16
Document Reference No.: FT_000401
USB 2.0 HI-SPEED TO MPSSE CABLE Datasheet
Version 1.0
Clearance No.: FTDI# 214
Appendix C – Revision History
Version 1.0
First Release
21st July 2011
Copyright © 2011 Future Technology Devices International Limited
17