DIP Switches SMT Half Pitch Type DIP Switches DX48 Series DX48L Terminal Length 8.1mm PCB LAYOUT 02 04 06 08 10 CODE OF 2 DX48S Terminal Length 6.7mm PCB LAYOUT How to order: 1 2 Material: 3 4 5 DX48 1 L S 2 02 04 06 08 10 TERMINAL LENGTH: 8.1 mm 6.7 mm NO. OF POSITIONS: 2 Positions 4 Positions 6 Positions 8 Positions 10 Positions [email protected] 3 ACTUATOR POSITION: F In OFF Position (Standard) O In ON Position 4 SEAL: N Regular (Standard) T Top Tape Sealed 5 PACKAGE STYLE: TB Tube TR Tape & Reel Item Description Materials 1 Cover High-Temp. Thermoplastic Nylon UL94V-0 2 Actuator High-Temp. Thermoplastic LCP 3 Contact Phosphor Bronze 4 Terminal Brass 5 Base High-Temp. Thermoplastic Nylon UL94V-0 6 Tape Katpon Treatment Molded Black Molded White Gold Plated Gold Plated Molded Black www.greatecs.com 1 DIP Switches SMT Half Pitch Type DIP Switches DX48 Series SPECIFICATIONS 1. Style: This specification describes "SMT HALF PITCH TYPE DIP SWITCHES” mainly used as signal switch of electric devices, with the general requirements of mechanical and electrical characteristics. 1.1 Operating Temperature Range : -40к~+85к 1.2 Storage Temperature Range :-40к~+85к 2. Current Range: 2.1 Non-Switching: 100mA, 50V DC 2.2 Switching: 25mA, 24V DC 3. Type of Actuation: Actuated by sliding 4. Test Sequence: MELECTRIC PERFORMANCE ITEM DESCRIPTION 1. Visual Examination 2. Contact Resistance 3. Insulation Resistance Dielectric 4. withstanding Voltage 5. Capacitance [email protected] TEST CONDITIONS REQUIREMENTS There shall be no By visual examination check without defects that affect the any out pressure & testing. serviceability of the product. 1)To be measured between the two terminals associated with each switch pole. 100m max. (initial) 2)Measurements shall be made with a 1 kHz shall current contact resistance meter. 500 V DC , 1 minute±5 sec. 300 V AC (50Hz or 60 Hz) shall be applied between all the adjacent terminals and between the terminal and the frame for 1 minute. 1MHz±10kHz 100M min There shall be no breakdown or flashover. 5 pF max. www.greatecs.com 2 DIP Switches SMT Half Pitch Type DIP Switches DX48 Series Applied in the direction of operation. ON OFF 30°~120° OFF ON MECHANICAL PERFORMANCE 6 7 500 gf max 㧔4.9N max㧕 Operation Force Stop Strength 1 kgf is applied in the operating direction There shall be no sign of and pulling direction operated for a damage mechanically. period of 15 seconds. 1)Soldering Temperature : Soldering 8 Heat Resistance 9 Vibration 10 Shock [email protected] PROD SMT TYPE TERMINAL SERIES TEMP 260±5к TIME 5~10sce 2)Duration of Solder Immersion: 5±1seconds. 3)Frequency of Solder Process: 1 times max. (PCB is 1.6 mm in thickness.) Shall be vibrated in accordance with Method 201A of MIL-STD-202F 1)Frequency: 10-55-10 Hz 1 min/cycle. 2)Direction: 3 vertical directions including the direction of operation 3)Test Time: 2 hours each direction. Shall be shocked in accordance with Method 213B Condition A of MIL-STD202F 1)Acceleration : 50G 2)Action Time : 11±1 m seconds 3)Testing Direction : 6 sides 4)Test cycle : 3 times in each direction 1)As shown in item 3~6 2)Contact Resistance: 2 max. (final-after test) 1)As shown in item 2~6 2)Contact Resistance: 2 max.) (final-after test) 1)As shown in item 2~6 2)Contact Resistance: 2 max. (final-after test) www.greatecs.com 3 DIP Switches WEATHER-PROOF DURABILITY SMT Half Pitch Type DIP Switches Measurements shall be made following the test set forth below: 1)25mA,24 V DC resistive load 11 Operation Life 2)Rate of Operation : 15~20 cycles/minute 3)Cycle of Operation : 1000 cycles Following the test set forth below the sample shall be left in normal temperature and humidity conditions Resistance Low for an hour before measurements are 12 Temperature made : 1)Temperature : -40±3к 2)Time : 96 hours DX48 Series 1)As shown in item 3,4 2)Contact Resistance: 2 max. (final-after test) 1)As shown in item 2~6 2)Contact Resistance: 2 max. (final-after test) Following the test set forth below the 1)As shown in item sample shall be left in normal 3~6 Resistance High temperature and humidity conditions for 13 an hour before measurements are made : 2)Contact Resistance : Temperature 2max. 1)Temperature :85±2к (final-after test) 2)Time : 96 hours 14 Resistance Humidity [email protected] 1)As shown in item Following the test set forth below the sample shall be left in normal 4~6 temperature and humidity conditions for 2)Contact Resistance : an hour before measurements are made : 2max. 1)Temperature : 40±2к 3)Insulation 2)Relative Humidity : 90~95% Resistance: 3)Time : 96 hours 10 M min . www.greatecs.com 4 DIP Switches SMT Half Pitch Type DIP Switches 5. DX48 Series SOLDERING CONDITIONS: Condition for Soldering MAX 260° 255° 230° 150° Room Temperature 120~150sec 5~10sec 60sec TIME(sec) The condition mentioned above is the temperature on the Cu foil of the PCB surface. There are cases where board's temperature greatly differs from switch's surface temperature depending on board's material, size, thickness, etc. Care, therefore, should be used not to allow switch's surface temperature to exceed 260к. Manual Soldering Soldering Temperature Max,350к Continuous Soldering Time Max,5 seconds Precautions in Handling 1. Care should be exercised so that flux from the upper part of the printed circuit board does not adhere to the switch. 2. Don’t clean the switch body except with top tape sealed type, which can only spray of cleaning method from top of s/w. 3. Slide the DX48 actuator from sec operation. Z axial direction with in 30°~120°of max 300 gf / 10 30°~12 4. The suggest tool for actuator adjust is as below. ( example for 4 position ) [email protected] www.greatecs.com 5