HMC350MS8 / 350MS8E v03.0308 MIXERS - SINGLE & DOUBLE BALANCED - SMT 10 GaAs MMIC HIGH IP3 SINGLEBALANCED MIXER, 0.6 - 1.2 GHz D E U N I T N O T C C S U I D D O PR Typical Applications Features The HMC350MS8 / HMC350MS8E is ideal for: Conversion Loss: 8 dB • Cellular Basestations Input IP3: +27 dBm • Cable Modems Input IP2: +45 dBm • Fixed Wireless Access Systems Input P1dB: +17 dBm Functional Diagram ns g i s De ew N r fo d e end m General Description com e R The HMC350MS8 & HMC350MS8E are miniature Not single balanced mixers in 8 lead plastic surface mount packages. The passive GaAs schottky diode mixer implements planar on chip baluns and requires no external components. The mixer can be used as an upconverter, down converter, or modulator. The mixer provides 7.5 dB conversion loss and +25 dBm IIP3 with LO drive levels of +19 dBm at mid-band. The design was optimized for low cost high volume applications where high converter linearity is required. Electrical Specifi cations, TA = +25° C LO = +19 dBm, IF = 100 MHz Parameter Units Min. Typ. Max. Min. Typ. Frequency Range, RF & LO 0.6 - 1.2 0.8 - 1.0 Frequency Range, IF DC - 0.3 DC - 0.3 Conversion Loss Noise Figure (SSB) 8 12 8 12 Max. GHz GHz 7.5 10 dB 7.5 10 dB LO to RF Isolation 19 22 19 22 dB LO to IF Isolation 5 8 5 8 dB RF to IF Isolation 14 18 15 20 dB IP3 (Input) 23 27 23 27 dBm IP2 (Input) 33 45 38 45 dBm 1 dB Compression (Input) 14 17 14 17 dBm *Unless otherwise noted, all measurements performed as downconverter, IF= 100 MHz. 10 - 1 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC350MS8 / 350MS8E v03.0308 GaAs MMIC HIGH IP3 SINGLEBALANCED MIXER, 0.6 - 1.2 GHz D E U N I T N O T C C S U I D D O PR Conversion Gain vs. Temperature @ LO = +19 dBm Isolation @ LO = +19 dBm 0 -10 -10 -20 0.5 0.7 0.9 -30 wD e N or f d de n e mm o c Re t o N +25C -40C +85C -15 1.1 -40 -60 0.5 1.5 0.7 0.9 1.1 1.3 1.5 FREQUENCY (GHz) FREQUENCY (GHz) Return Loss @ LO = +19 dBm Conversion Gain vs. LO Drive 0 0 +11 dBm +13 dBm +15 dBm +17 dBm +19 dBm +21 dBm -5 RETURN LOSS (dB) CONVERSION GAIN (dB) ns g i s e RF/IF LO/RF LO/IF -50 1.3 10 -20 -10 -15 -20 0.5 0.7 0.9 1.1 1.3 -5 -10 -20 0.5 1.5 RF LO -15 0.7 FREQUENCY (GHz) 0.9 1.1 1.3 1.5 FREQUENCY (GHz) Upconverter Performance, Conversion Gain @ LO = +19 dBm IF Bandwidth @ LO = +19 dBm 0 0 CONVERSION GAIN (dB) RETURN LOSS CONVERSION GAIN RESPONSE (dB) -5 -10 -15 -20 0 0.2 0.4 0.6 IF FREQUENCY (GHz) 0.8 1 -5 -10 MIXERS - SINGLE & DOUBLE BALANCED - SMT -5 ISOLATION (dB) CONVERSION GAIN (dB) 0 -15 -20 0.5 0.7 0.9 1.1 1.3 1.5 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 - 2 HMC350MS8 / 350MS8E v03.0308 GaAs MMIC HIGH IP3 SINGLEBALANCED MIXER, 0.6 - 1.2 GHz D E U N I T N O T C C S U I D D O PR Input IP3 vs. LO Drive * 34 70 28 26 LO = + 17dBm LO = + 19dBm LO = + 21dBm 60 IP2 (dBm) IP3 (dBm) 30 55 50 45 ew N r fo d e end m com e R Not ns g i s De 40 24 22 0.6 35 0.7 0.8 0.9 1 1.1 1.2 1.3 30 0.6 1.4 0.8 Input IP3 vs. Temperature * @ LO Drive = +19 dBm 1.2 1.4 P1dB vs. Temperature @ LO = +19 dBm 34 26 -40C +25C +85C 32 24 P1dB (dBm) 30 28 26 24 22 0.6 1 FREQUENCY (GHz) LO FREQUENCY (GHz) IP3 (dBm) MIXERS - SINGLE & DOUBLE BALANCED - SMT 65 LO = +17 dBm LO = +19 dBm LO = +21 dBm 32 10 Input IP2 vs. LO Drive * +25 C -40 C +85 C 22 20 18 16 0.8 1 1.2 1.4 FREQUENCY (GHz) 14 0.7 0.8 0.9 1 1.1 1.2 FREQUENCY (GHz) * Two-tone input power = 0 dBm each tone, 1 MHz spacing. 10 - 3 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC350MS8 / 350MS8E v03.0308 GaAs MMIC HIGH IP3 SINGLEBALANCED MIXER, 0.6 - 1.2 GHz D E U N I T N O T C C S U I D D O PR MxN Spurious Outputs Harmonics of LO mRF nLO Spur at RF Port 0 1 2 3 4 0 xx -28 -3 6 1 1 14 0 37 38 29 2 58 59 63 51 82 3 87 85 85 4 >94 >94 >94 LO Frequency (GHz) 1 0.6 28 0.75 24 0.9 22 1.05 23 71 >92 76 1.2 RF = 1.0 GHz @ -10 dBm LO = 0.9 GHz @ +19 dBm All values in dBc relative to the IF output power level. 1.35 15 3 4 63 43 ns g i s e 16 60 46 46 18 48 20 48 52 26 22 52 59 28 26 57 63 wD e N or f d de n e mm o c Re t o N 77 2 LO = +19 dBm Values in dBc below input LO level measured at the RF port. Absolute Maximum Ratings RF / IF Input +27 dBm LO Drive +27 dBm Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C IF DC Current ±18 mA ESD Sensitivity (HBM) Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 MIXERS - SINGLE & DOUBLE BALANCED - SMT nLO 10 - 4 HMC350MS8 / 350MS8E v03.0308 GaAs MMIC HIGH IP3 SINGLEBALANCED MIXER, 0.6 - 1.2 GHz D E U N I T N O T C C S U I D D O PR Outline Drawing MIXERS - SINGLE & DOUBLE BALANCED - SMT 10 10 - 5 ew N r fo d e end m com e R Not ns g i s De NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC350MS8 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC350MS8E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H350 XXXX [2] H350 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC350MS8 / 350MS8E v03.0308 GaAs MMIC HIGH IP3 SINGLEBALANCED MIXER, 0.6 - 1.2 GHz D E U N I T N O T C C S U I D D O PR Evaluation PCB List of Materials for Evaluation PCB 101830 [1] Item Description J1, J2, J3 PCB Mount SMA RF Connector U1 HMC350MS8 / HMC350MS8E Mixer PCB [2] 101828 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board as shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 10 MIXERS - SINGLE & DOUBLE BALANCED - SMT wD e N or f d de n e mm o c Re t o N ns g i s e 10 - 6