PT7771—5V 32 Amp “Sledge Hammer” Programmable ISR SLTS054A (Revised 6/30/2000) The PT7771 is a high-output Integrated Switching Regulator (ISR) housed in a 27-pin SIP package. The PT7771 operates off a standard 5V bus to provide a 32 amp low-voltage power source for the industry’s latest highspeed µPs, ASICs, DSPs. The PT7771 has been designed to work in parallel with one or more of the PT7746 -32A current boosters to increase the load current capability in increments of 32A. The output voltage is programmable from 1.3V to 3.5V via a 5-bit input, compatible with Intel’s Pentiumâ Pro Processor. A differential remote sense is also provided to compensate for voltage drop between the ISR and load. An output capacitance of 2400µF is required for proper operation. Note that this product does not include short circuit protection. Pin-Out Information Standard Application PROGRAMMING PINS VID0 VID1 VID2 VID3 VID4 VIN REMOTE SENSE (+) 6 4 3 2 1 L1 PT7770 7 - 11 1H C IN + 26 27 13 - 19 5 VOUT 20 - 25 12 C OUT + LOAD SYNC OUT GND GND STBY* REMOTE SENSE (-) Cin = Required 2400µF electrolytic Cout = Required 2400µF electrolytic L1 = Optional 1µH input choke Pin Function 1 VID0 2 VID1 3 VID2 4 VID3 5 STBY*- Stand-by 6 VID4 7 Vin 8 Vin 9 Vin 10 Vin 11 Vin 12 Remote Sense Gnd 13 GND Pin Function 14 GND 15 GND 16 GND 17 GND 18 19 20 21 22 23 24 25 26 27 GND GND Vout Vout Vout Vout Vout Vout Remote Sense Vout Sync Out For STBY* pin; open = output enabled; ground = output disabled. Specifications PT7771 Characteristics (T a = 25°C unless noted) Symbols Conditions Min Output Current Io Ta = +60°C, 200 LFM, pkg N Ta = +25°C, natural convection 0.1 0.1 Input Voltage Range Vin 0.1A ≤ Io ≤ 32A 4.5 Output Voltage Tolerance ∆Vo Vin = +5V, Io = 32A 0°C ≤ Ta ≤ +55°C Line Regulation Regline Load Regulation Regload Vo Ripple/Noise pk-pk Typ Max Units (1) (1) — — 32 26 A A (2) — 5.5 V Vo-0.03 — Vo+0.03 V 4.5V ≤ V in ≤ 5.5V, Io = 32A — ±10 — mV Vin = +5V, 0.1 ≤ I o ≤ 32A — ±10 — mV Vn Vin = +5V, Io = 32A — 50 — mV Transient Response with Cout = 2400µF ttr Vos Io step between 16A and 32A Vo over/undershoot — — 100 200 — — µSec mV Efficiency η Vin = +5V, Io = 20A, V o = 3.3V — 90 — % Switching Frequency ƒo 4.5V ≤ Vin ≤ 5.5V 0.1A ≤ Io ≤ 32A 650 700 750 kHz Absolute Maximum Operating Temperature Range Ta Over Vin Range 0 — +85 Storage Temperature Ts — -40 — +125 °C Weight — Vertical/Horizontal — 53/66 — grams (3) Notes: (1) ISR-will operate down to no load with reduced specifications. Please note that this product is not short-circuit protected. (2) The minimum input voltage is 4.5V or Vout +1.2V, whichever is greater. (3) Consult the SOA curves or contact the factory for the appropriate derating. Output Capacitors: The PT7771 regulator requires a minimum output capacitance of 2400µF for proper operation. Do not use Oscon type capacitors. The maximum allowable output capacitance is 30,000µF. Input Filter: An input filter is optional for most applications. The input inductor must be sized to handle 32ADC with a typical value of 1µH. The input capacitance must be rated for a minimum of 2.6Arms of ripple current. For transient or dynamic load applications, additional capacitance may be required. For technical support and more information, see inside back cover or visit www.ti.com/powertrends °C PT7771—5V 32 Amp “Sledge Hammer” Programmable ISR Programming Information Features • +5V input • 5-bit Programmable: 1.3V to 3.5V@32A • High Efficiency • Differential Remote Sense • Parallelable with PT7746 32A “Current Booster” • 27-pin SIP Package VID3 VID2 VID1 VID0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 Ordering Information PT7771❏ ❏ = 1.3 to 3.5 Volts VID4=1 VID4=0 Vout Vout 2.0V 2.1V 2.2V 2.3V 2.4V 2.5V 2.6V 2.7V 2.8V 2.9V 3.0V 3.1V 3.2V 3.3V 3.4V 3.5V For dimensions and PC board layout, see Package Style 1020 and 1030 1.30V 1.35V 1.40V 1.45V 1.50V 1.55V 1.60V 1.65V 1.70V 1.75V 1.80V 1.85V 1.90V 1.95V 2.00V 2.05V PT Series Suffix (PT1234X) Case/Pin Configuration N A C Vertical Through-Hole Horizontal Through-Hole Horizontal Surface Mount Logic 0 = Pin 12 potential (remote sense gnd) Logic 1 = Open circuit (no pull-up resistors) VID3 and VID4 may not be changed while the unit is operating. T Y P I C A L PT7771 @Vin =+5V, Vout =3.3V C H A R A C T E R I S T I C S Safe Operating Area Curves (See Note A) Efficiency vs Output Current 100 Vin 4.5V 5.0V 5.5V 80 70 60 0 4 8 12 16 20 24 28 Ambient TTemperature emperature (°C) 90 90 Efficiency (%) (See Note B) PT7771 @Vin =+5V, Vout =3.3V, Pkg N 80 70 Airflow Nat. Conv 60 60 LFM 120 LFM 200 LFM 50 40 30 20 32 0 Output Current (A) 4 8 12 16 20 24 28 32 Output Current (A) Power Dissipation vs Output Current 20 18 16 Vin Pd (W atts) (Watts) 14 12 4.5V 10 5.0V 5.5V 8 6 4 2 0 0 4 8 12 16 20 24 28 32 Output Current (A) Output Ripple vs Output Current 40 35 Ripple (mVpp) 30 Vin 25 4.5V 5.0V 5.5V 20 15 10 5 0 0 4 8 12 16 20 24 28 32 Output Current (A) Note A: All characteristic data in the above graphs has been developed from actual procducts tested at 25°C. This data is considered typical for the ISR. Note B: OA curves represent operating conditions at which internal components are at or below manufacturer’s maximum rated operating temperatures. For technical support and more information, see inside back cover or visit www.ti.com/powertrends PACKAGE OPTION ADDENDUM www.ti.com 10-Jan-2013 PACKAGING INFORMATION Orderable Device Status (1) PT7771C Package Type Package Pins Package Qty Drawing Eco Plan Lead/Ball Finish MSL Peak Temp Samples (3) (Requires Login) (2) LIFEBUY SIP MODULE EJC 27 6 TBD Call TI Level-1-215C-UNLIM PT7771N LIFEBUY SIP MODULE EJD 27 8 TBD Call TI Level-1-215C-UNLIM PT7771N1 OBSOLETE SIP MODULE EJD 27 TBD Call TI Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated