www.make-ps.com E-mail:[email protected] 800 series Single, Dual, Triple Output DC/DC Converter FEATURES • • • • • • Synchronization 6 sided Continuous Shielding 9.38W/In3 Power Density Efficiency to 82% VDE / EN 60950 Approved >1,000,000 Hours MTBF DESCRIPTIONS INPUT CHARACTERISTICS The 800 series is family of miniature, high performance and high reliability DC/DC converters. The 800 series operates over 2:1 input voltage ranges of 9 to 18, 18 to 36 or 36 to 72VDC; providing single, dual and triple output combinations of 5, 12, 15, ±5, ±12, ±15, 5/±12 and 5/±15 VDC. Standard features include 500VDC input/output isolation, efficiency as high as 82%, tight line/load regulation and low output ripple and noise. All 24 models are packaged in compact, low profile 1” X 2” X 0.4” metal cases. Min Typ Max Unit/Comments Input Voltage Range 12 VDC Input Models VDC 9 12 18 24 VDC Input Models VDC 18 24 36 48 VDC Input Models VDC 36 48 72 Remote On / OFF Control Supply ON 0 VDC to 0.6 VDC Supply OFF 1 VDC to 5 VDC Logic Referenced to Negative Input Input Filter LC Type Input Fuse Rating See Model Selection Guide OUTPUT CHARACTERISTICS Min Typ Max Unit/Comments Output Voltage Accuracy Single & Dual Outputs ±1.0 % 1 Triple Outputs - Primary ±1.0 % 1 - Auxiliaries ±6.0 % 1 Voltage Balance: Dual Outputs ±1.0 %; Equal Output Loads Triple Outputs (Auxiliaries) ±1.0 %; Equal Output Loads Minimum Load Full Load 10% Line Regulation Single & Dual Outputs ±0.5 % 2 Triple Outputs - Primary ±0.5 % 2 - Auxiliaries 5.0 % 2 Load Regulation Single Outputs ±0.5 % 3 Dual Outputs ±1.0 % 3 ; Equal Loads Triple Outputs - Primary ±0.5 % 3 - Auxiliaries ±6.0 % 3 ; Equal Loads Ripple/Noise 2 % of Vout (20 MHz B.W.) Short Circuit Protection Continuous, Automatic Recovery Transient Recovery Time 200 μS to within1% error band for 50% step load change Temperature Coefficient ±0.01 % per oC Over Voltage Protection See Model Selection Guide GENERAL CHARACTERISTICS Switching Frequency Isolation Voltage Isolation Resistance MTBF (MIL-HBK-217F) 1 2 3 Min Typ Max Unit/Comments kHz 100 VDC, 1 minute 500 Mohm, 500VDC 1000 Million Hours, 1 +25oC, Ground Benign = Output voltage at nominal line & FL = % Output voltage measured from min. input line to maximum = Output voltage measured from FL to 10% Load >> B-85 www.make-ps.com E-mail:[email protected] ENVIRONMENTAL SPECIFICATIONS Operating Temp. Range Storage Temp. Range Relative Humidity Min -30 -40 PHYSICAL CHARACTERISTICS Typ Max +75 +125 95 Cooling Unit/Comments o C; Ambient o C % Humidity; noncondensing Free-Air Convection Unit/Comments 1.0 X 2.0 X 0.4 inches (25.5 X 51.0 X 10.2 mm) Coated Metal Case Size Case Material Shield Connection 12V and 24V Input Models 48V Input Models Flammability Weight Negative Input, Pin 3 Positive Input, Pin 4 UL94V-0 42.5 Grams OUTLINE DRAWING 1.00 (25.4) 0.10 (2.5) 0.20 0.20 0.20 0.20 (5.1) (5.1) (5.1) (5.1) 0.10 (2.5) 9 8 7 6 5 2.00 (50.8) BOTTOM 4 3 2 SIDE 1 0.10 (2.5) .20 .20 .20 .20 (5.1) (5.1) (5.1) (5.1) .040± .005 (1.0) DIA. 0.30. (7.6) 0.40 (10.2) PIN OUT CHART Pin 1 2 3 4 5 6 7 8 9 Single Dual Triple Remote On/Off Remote On/Off Remote On/Off Sync Sync Sync - Vin - Vin - Vin + Vin + Vin + Vin NC - Vout - Vout (Aux) NC Common Common(Aux) NC + Vout +Vout (Aux) - Vout NC +5V Common + Vout NC +5V Vout Notes: 1. Unless otherwise specified dimensions are in inches (mm). Tolerances Inches mm X.XX = ±0.02 X.X = ±0.5 NC = No Connection All specifications are typical at nominal input, nominal load and 25° C unless otherwise specified. External, low ESR, 10 microfarad (minimum) capacitor across output is recommended for operation. >> B-86 www.make-ps.com E-mail:[email protected] HOW TO ORDER HOW TO ORDER SINGLE AND DUAL OUTPUT 8 XX D XX Nominal Input Voltage Wattage Output Voltage Output Configuration (S=Single, D=Dual) TRIPLE OUTPUT 8 XX / 15 T XX Nominal Input Voltage Wattage Main Output Voltage Aux Output Voltage Output Configuration (T= Triple) MODEL SELECTION CHART Model 805S12 812S12 815S12 805D12 812D12 815D12 805S24 812S24 815S24 805D24 812D24 815D24 805S48 812S48 815S48 805D48 812D48 815D48 805/12T12 805/15T12 805/12T24 805/15T24 805/12T48 805/15T48 Nominal Input Voltage (VDC) Output Voltage (VDC) Full Load Output Current (mA) No Load Input Current (mA) 12 12 12 12 12 12 24 24 24 24 24 24 48 48 48 48 48 48 12 12 24 24 48 48 5 12 15 ±5 ±12 ±15 5 12 15 ±5 ±12 ±15 5 12 15 ±5 ±12 ±15 5, ±12 5, ±15 5, ±12 5, ±15 5, ±12 5, ±15 1500 625 500 ±750 ±300 ±250 1500 625 500 ±750 ±300 ±250 1500 625 500 ±750 ±300 ±250 1000±100 1000±100 1000±100 1000±100 1000±100 1000±100 46 46 46 46 46 46 55 55 55 55 55 55 40 40 40 40 40 40 42 42 42 42 40 40 Input Full Load Reflected Input Ripple Current Current (mA) (mA) 780 786 786 786 786 786 384 384 384 382 382 382 198 198 198 204 198 198 843 843 411 411 203 203 30 30 30 30 30 30 40 40 40 40 40 40 30 30 30 30 30 30 36 36 36 36 33 33 Output Over Voltage (VDC) Fuse (mA) Efficiency @ FL (%) 6.8 15.0 18.0 ±6.8 ±15.0 ±18.0 6.8 15.0 18.0 ±6.8 ±15.0 ±18.0 6.8 15.0 18.0 ±6.8 ±15.0 ±18.0 6.8, ±15.0 6.8, ±18.0 6.8, ±15.0 6.8, ±18.0 6.8, ±15.0 6.8, ±18.0 1500 1500 1500 1500 1500 1500 750 750 750 750 750 750 500 500 500 500 500 500 2000 2000 1000 1000 500 500 79 79 79 79 80 80 81 81 82 82 82 82 79 79 79 78 79 79 79 79 81 81 82 82 >> B-87