LPC-60 60W Single Output Switching Power Supply series Features : Constant current design Universal AC input / Full range Withstand 300VAC surge input for 5 seconds Protections: Short circuit / Over voltage Cooling by free air convection Fully encapsulated with IP67 level (Note.8) Fully isolated plastic case Class power unit, no FG Class 2 power unit Pass LPS Suitable for LED lighting and moving sign applications (Note.7) 100% full load burn-in test Low cost, high reliability 2 years warranty LPS IP67 SPECIFICATION MODEL LPC-60-1050 LPC-60-1400 LPC-60-1750 1050mA 1400mA 1750mA DC VOLTAGE RANGE 9 ~ 48V 9 ~ 42V 9 ~ 34V RATED POWER 50.4W 58.8W 59.5W 200mVp-p 200mVp-p VOLTAGE TOLERANCE Note.3 5.0% CURRENT ACCURACY 5.0% LINE REGULATION 1.0% 2.0% LOAD REGULATION SETUP, RISE TIME Note.6 500ms, 120ms / 230VAC 50ms/230VAC HOLD UP TIME (Typ.) VOLTAGE RANGE INPUT Note.4 90 ~ 264VAC EFFICIENCY (Typ.) 87% AC CURRENT (Typ.) INRUSH CURRENT(max.) 1.2A/115VAC 0.7A/230VAC COLD START 30A/115VAC LEAKAGE CURRENT 0.25mA / 240VAC WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT 87% 60A/230VAC 50.4 ~ 60V 44.1 ~ 56.7V 39.1 ~ 45.9V Protection type : Shut off o/p voltage, clamping by TVS diode -30 ~ +70 (Refer to "Derating Curve") 20 ~ 90% RH non-condensing -40 ~ +80 , 10 ~ 95% RH VIBRATION SAFETY STANDARDS UL1310, CAN/CSA C22.2 No. 223-M91(for LPC-60-1750 only), IP67 approved ; design refer to TUV EN60950-1 WITHSTAND VOLTAGE I/P-O/P:3KVAC ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55022 (CISPR22) Class B, EN61000-3-2 Class A, EN61000-3-3 EMC EMISSION EMC IMMUNITY DIMENSION PACKING NOTE 85% 0.03%/ (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes MTBF OTHERS 127 ~ 370VDC 47 ~ 63Hz WORKING TEMP. EMC 500ms, 120ms / 115VAC at full load 16ms/115VAC at full load FREQUENCY RANGE PROTECTION OVER VOLTAGE SAFETY & ( for 1750mA only) RATED CURRENT RIPPLE & NOISE (max.) Note.2 200mVp-p OUTPUT ( except for 1750mA ) Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A 732Khrs min. MIL-HDBK-217F (25 ) 162.5*42.5*32mm (L*W*H) 0.4Kg; 32pcs/13.8Kg/0.56CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage. Please check the static characteristics for more details. 5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. 7. The unit might not be suitable for lighting applications in EU countries. Please check with your local authorities for the possible use of the unit. 8. Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minute. File Name:LPC-60-SPEC 2012-03-20 LPC-60 60W Single Output Switching Power Supply Mechanical Specification Case No. 976A 162.5 600 30 series Unit:mm 600 30 3.5 3.6 42.5 15 UL1015 18AWG AC/N(Blue) AC/L(Brown) 3.6 81.5 T case 3.5 3.5 UL1007 16AWG +V(Red) -V(Black) 3.5 32 T case: Max. Case Temperature. Recommend Mounting Direction Block Diagram fosc : 60KHz EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING +V -V O.C.P. O.L.P. PWM CONTROL Derating Curve DETECTION CIRCUIT Static Characteristics 100 100 90 80 80 70 LOAD (%) LOAD (%) 60 40 20 -30 -15 0 15 30 40 50 AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) 60 50 40 90 100 125 135 145 155 165 175 180 200 230 264 INPUT VOLTAGE (V) 60Hz File Name:LPC-60-SPEC 2012-03-20