18W Single Output Switching Power Supply LPL-18 series Features : 90-132VAC input only Fully encapsulated with IP67 level (Note.5) Protections:Short circuit/Over load/Over voltage/Over temperature Cooling by free air convection Pass LPS 100% full load burn-in test Suitable for LED lighting and moving sign applications High reliability/Low cost 2 years warranty LPS IP67 SPECIFICATION MODEL OUTPUT LPL-18-12 LPL-18-24 LPL-18-36 DC VOLTAGE 12V 24V 36V RATED CURRENT 1.5A 0.75A 0.5A CURRENT RANGE 0 ~ 1.5A 0 ~ 0.75A 0 ~ 0.5A RATED POWER 18W 18W 18W 150mVp-p 200mVp-p 83% 84% RIPPLE & NOISE (max.) Note.2 120mVp-p VOLTAGE TOLERANCE Note.3 3.0% LINE REGULATION 1.0% LOAD REGULATION INPUT 2.0% SETUP, RISE TIME 1500ms, 30ms / 115VAC HOLD UP TIME (Typ.) 20ms/115VAC at full load VOLTAGE RANGE 90 ~ 132VAC FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY(Typ.) 80% AC CURRENT INRUSH CURRENT(max.) 0.5A/115VAC Cold start 40A/115VAC 127 ~ 186VDC LEAKAGE CURRENT 0.25mA / 115VAC OVER CURRENT Above 105% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed PROTECTION OVER VOLTAGE 13.8~ 16.2V WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION 27.6~ 32.4V 41.4 ~ 48.6V Protection type : Shut off o/p voltage, clamping by zener diode Tj 140 OVER TEMPERATURE (LVD) typically (U1) detect on main control IC Protection type :Shut down, recovers automatically after temperature goes down -30 ~ 70 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +80 0.03%/ , 10 ~ 95% RH (0 ~ 50 ) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS IP67 approved; design refer to UL1310 Class 2,TUV EN60950-1, EN61347-2-13, CAN/CSA C22.2 No. 223-M91 WITHSTAND VOLTAGE I/P-O/P:3KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH EMC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B, FCC Part 15 HARMONIC CURRENT EMS IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE Compliance to EN61000-3-2 Class A,EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A 1207.4Khrs min. MIL-HDBK-217F(25 140*30*22(L*W*H) 0.175Kg; 70pcs/13.3Kgs/0.71CUFT ) 1. All parameters NOT specially mentioned are measured at 115VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 5. Suitable for indoor use or outdoor use without direct sunlight exposure. File Name: LPL-18-SPEC 2011-03-09 LPL-18 18W Single Output Switching Power Supply Mechanical Specification series Unit:mm 300 20 300 20 140 3.6 3.5 30 3.6 DC OUT AC IN 18AWG 1015 AC/N(Blue) AC/L(Brown) 3.5 3.5 18AWG 1015 -V(Black) +V(Red) 22 3.5 Block Diagram I/P fosc : 60KHz EMI FILTER RECTIFIERS & FILTER POWER SWITCHING RECTIFIERS +V -V DETECTION CIRCUIT PWM CONTROL Derating Curve Static Characteristics Ta=25 100 100 90 80 80 70 LOAD (%) LOAD (%) 60 40 20 -30 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) 60 50 40 90 100 110 120 132 INPUT VOLTAGE (VAC) 60Hz File Name: LPL-18-SPEC 2011-03-09