TI TPS650732TRSLRQ1

TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
Single Chip Power Solution for Battery Powered Systems
Check for Samples: TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
FEATURES
1
•
•
2
•
•
•
•
Qualified for Automotive Applications
Charger/Power Path Management:
– 2A Output Current on the Power Path
– Linear Charger; 1.5A Maximum Charge
Current
– 100mA/500mA/ 800mA/1300mA Current
Limit From USB Input
– Thermal Regulation, Safety Timers
– Temperature Sense Input
3 Step-Down Converters:
– 2.35MHz Fixed Frequency Operation
– Up to 1.5A of Output Current
– Adjustable or Fixed Output Voltage
– VIN Range From 2.8V to 6.3V
– Power Save Mode at Light Load Current
– Output Voltage Accuracy in PWM Mode
±1.5%
– Typical 19 mA Quiescent Current per
Converter
– 100% Duty Cycle for Lowest Dropout
LDOs:
– Fixed Output Voltage
– Dynamic Voltage Scaling on LDO2
– 20mA Quiescent Current
– 200mA Maximum Output Current
– VIN Range From 1.8V to 6.3V
wLED Boost Converter:
– Internal Dimming Using I2C
– Up to 2 × 10 LEDs
– Up to 25mA per String With Internal Current
Sink
2
I C Interface
•
•
•
10 Bit A/D Converter
Touch Screen Interface
Undervoltage Lockout and Battery Fault
Comparator
APPLICATIONS
•
•
Portable Navigation Systems
Low-Power DSP Supply
DESCRIPTION
The TPS6507x are single chip Power Management
ICs for portable applications consisting of a battery
charger with power path management for a single
Li-Ion or Li-Polymer cell. The charger can either be
supplied by a USB port on pin USB or by a dc voltage
from a wall adapter connected to pin AC. Three
highly efficient 2.25MHz step-down converters are
targeted at providing the core voltage, memory and
I/O voltage in a processor based system. The
step-down converters enter a low power mode at light
load for maximum efficiency across the widest
possible range of load currents. For low noise
applications the devices can be forced into fixed
frequency PWM using the I2C interface. The
step-down converters allow the use of small inductors
and capacitors to achieve a small solution size. The
TPS6507x also integrate two general purpose LDOs
for an output current of 200mA. These LDOs can be
used to power an SD-card interface and an
always-on rail, but can be used for other purposes as
well. Each LDO operates with an input voltage range
between 1.8V and 6.3V allowing them to be supplied
from one of the step-down converters or directly from
the main battery. An inductive boost converter with
two programmable current sinks power two strings of
white LEDs.
The TPS6507x come in a 48-pin leadless package
(6mm × 6mm QFN) with a 0.4mm pitch.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011, Texas Instruments Incorporated
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
TA
-40°C to
105°C
(1)
OUTPUT VOLTAGE
AT DCDC3
OUTPUT
VOLTAGE AT
DCDC1/DCDC2
OUTPUT
VOLTAGE AT
LDO1/LDO2
OUTPUT CURRENT
AT
DCDC1/DCDC2/DCD
C3
1.0V / 1.2V
(OMAP-L1x8)
3.3V
1.8V / 3.3V
1.8V / 1.2V
0.6A / 1.5A / 1.5A
VQFN-48 RSL
1.2V / 1.4V
(Atlas IV)
3.3V
1.8V / 2.5V
1.2V / 1.2V
3 x 600 mA
1.2V / 1.35V
(OMAP35xx)
1.8V
1.2V / 1.8V
1.8V / 1.8V
1.2V / 1.35V
(OMAP35xx)
1.8V
1.2V / 1.8V
1.2V / 1.35V
(AM3505)
1.8V
1.8V / 3.3V
PART NUMBER (1)
TOP-SIDE
MARKING
Reel of 2500
TPS65070TRSLRQ1
Preview
VQFN-48 RSL
Reel of 2500
TPS65072TRSLRQ1
Preview
0.6A / 0.6A / 1.5A
External sequencing
VQFN-48 RSL
Reel of 2500
TPS65073TRSLRQ1
Preview
1.8V / 1.8V
0.6A / 0.6A / 1.5A
Internal sequencing
VQFN-48 RSL
Reel of 2500
TPS650731TRSLRQ1
Preview
1.8V / 1.8V
0.6A / 0.6A / 1.5A
Internal sequencing
VQFN-48 RSL
Reel of 2500
TPS650732TRSLRQ1
TPS650732T
PACKAGE
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VALUE / UNIT
Voltage range on all pins except the pins listed below with respect to AGND
–0.3 to 7V
Voltage range on pins INT, RESET, PGOOD, PB_OUT with respect to AGND
–0.3 to V(AVDD6)
Voltage range on pins VINDCDC1/2, VINDCDC3, VINLDO respect to AGND
–0.3 to V(SYS)
Voltage range on pins AD_IN1, AD_IN2, AD_IN3, AD_IN4 with respect to AGND
–0.3 to 3.3 V
Voltage range on pins ISINK1, ISINK2, AC, USB
–0.3 to 20 V
Voltage range on pin L4 (output voltage of boost converter), FB_wLED
–0.3 to 40 V
Current at SYS, AC, USB, BAT, L3
3000 mA
Current at all other pins
1000 mA
Continuous total power dissipation
See Dissipation Rating Table
Operating free-air temperature, TA
40°C to 105°C
Maximum junction temperature, TJ
125°C
Storage temperature, Tst
(1)
–65°C to 150°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATINGS (1)
PACKAGE
RqJA
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
TA = 105°C
POWER RATING
RSL
37 K/W
2.6 W
26 mW/K
1.48 W
1.0 W
520 mW
(1)
2
The thermal resistance RqJ-P junction to PowerPAD of the RSL package is 1.1 K/W. The value for RqJ-A was measured on a high K
board.
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
RECOMMENDED OPERATING CONDITIONS
MIN
NOM
MAX
UNIT
BATTERY CHARGER AND POWER PATH
VIN
Input voltage for power path manager at pins AC or USB
4.30
17
Input voltage for power path manager at pins AC or USB, charger and power path
active (no overvoltage lockout)
4.30
5.8
3.6
17
Input voltage for power path manager at pins AC or USB in case there is no battery
connected at pin BAT
IIN
IBAT
Input current at AC pin
2.5
Input current at USB pin
1.3
Current at BAT pin
V
A
2
A
DCDC CONVERTERS AND LDOs
VINDCDC
Input voltage range for step-down converter DCDC1, DCDC2, DCDC3
2.8
6.3 (1)
V
VDCDC1
Output voltage range for VDCDC1 step-down converter
0.6
VINDCDC1
V
VDCDC2
Output voltage range for VDCDC2, DCDC3 step-down converter
0.6
VINDCDC2
V
(1)
V
VINLDOx
Input voltage range for LDO1 and LDO2
1.8
VLDO1
Output voltage range for LDO1
0.9
3.3
V
VLDO2
Output voltage range for LDO2
0.8
3.3
V
IOUTDCDC1
Output current at L1
L1
Inductor at L1
CINDCDC12
Input Capacitor at VINDCDC1 and VINDCDC2 (2)
22
COUTDCDC1
Output Capacitor at VDCDC1 (2)
10
IOUTDCDC2
Output current at L2
L2
Inductor at L2 (2)
COUTDCDC2
Output Capacitor at VDCDC2
IOUTDCDC3
Output current at L3
L3
Inductor at L3 (2)
1.5
CINDCDC3
Input Capacitor at VINDCDC3 (2)
10
(2)
10
(2)
1.5
(2)
6.3
600
mA
2.2
mH
mF
22
mF
1500
mA
1.5
2.2
mH
10
22
mF
1500
mA
2.2
mH
mF
COUTDCDC3
Output Capacitor at VDCDC3
L4
Inductor at L4
COUTWLED
Output Capacitor at wLED boost converter
4.7
mF
CINLDO1/2
Input Capacitor at VINLDO1/2
2.2
mF
COUTLDO1
Output Capacitor at VLDO1
2.2
IOUTLDO1
Output Current at VLDO1
COUTLDO2
Output Capacitor at VLDO2
IOUTLDO2
Output Current at VLDO2
CAC
Input Capacitor at AC
1
mF
CUSB
Input Capacitor at USB
1
mF
CBAT
Capacitor at BAT pin
10
CSYS
Capacitor at SYS pin
22
CBYPASS
Capacitor at BYPASS pin
10
mF
CINT_LDO
Capacitor at INT_LDO pin
2.2
mF
CAVDD6
Capacitor at AVDD6 pin
4.7
TA
Operating ambient temperature
–40
105
°C
TJ
Operating junction temperature
–40
125
°C
(1)
(2)
(3)
(2)
22
mF
22
mH
mF
100
mA
2.2
mF
100
mA
mF
100
(3)
mF
mF
6.3 V or VSYS whichever is less
See application section for more details
For proper soft-start
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
3
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
VSYS = 3.6V, EN_DCDCx = VSYS, L = 2.2mH, COUT = 10mF, TA = –40°C to 105°C typical values are at TA = 25°C (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
VINDCDC Input voltage range for DCDC converters
2.8
Only DCDC2, DCDC3 and LDO1 enabled, device in
ON-mode; DCDC converters in PFM
IQ
ISD
VUVLO
TSD
Operating quiescent current
Total current into VSYS, VINDCDCx, VINLDO1/2
6.3
140
Per DC/DC converter, PFM mode
19
Per DC/DC converter, PWM mode
2.5
For LDO1 or LDO2 (either one enabled)
20
For LDO1 and LDO2 (both enabled)
34
For wLED converter
1.5
Shutdown current
All converters, LDOs, wLED driver and ADC disabled, no
input voltage at AC and USB;
SYS voltage turned off
Undervoltage lockout threshold
Voltage at the output of the power manager detected at pin
SYS; falling voltage, voltage defined with <UVLO0>,
<UVLO1> DEFAULT: 3.0V
Undervoltage lockout hysteresis
Rising voltage defined with <UVLO hysteresis>; DEFAULT:
500mV
Undervoltage lockout deglitch time
Due to internal delay
Thermal shutdown for DCDC converters, wLED
driver and LDOs
Thermal shutdown hysteresis
V
–2%
30
mA
35
mA
8
12
2.8
3.0
3.1
3.25
2%
mA
V
360
450
mV
4
ms
Increasing junction temperature
150
°C
Decreasing junction temperature
20
°C
EN_DCDC1, EN_DCDC2, EN_DCDC3, DEFDCDC2, DEFDCDC3, SDAT, SCLK, EN_wLED (optional)
VIH
High Level Input Voltage, EN_DCDC1,
EN_DCDC2, EN_DCDC3, DEFDCDC2,
DEFDCDC3, SDAT, SCLK, EN_wLED
1.2
VSYS
V
VIL
Low Level Input Voltage, EN_DCDC1,
EN_DCDC2, EN_DCDC3, DEFDCDC2,
DEFDCDC3, SDAT, SCLK, EN_wLED
0
0.4
V
IIN
Input bias current, EN_DCDC1, EN_DCDC2,
EN_DCDC3, DEFDCDC2, DEFDCDC3, SDAT,
SCLK
1.0
mA
4
Submit Documentation Feedback
0.01
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
DCDC1 CONVERTER
PARAMETER
VVINDCDC1
Input voltage range
IO
Maximum output
RDS(ON)
High side MOSFET on-resistance
ILH
High side MOSFET leakage current
TEST CONDITIONS
MIN
Connected to SYS pin
TYP
MAX
2.8
mA
VINDCDC1 = 2.8 V
150
300
VINDCDC1 = 3.5 V
120
200
VINDCDC1 = 2.8 V
200
300
VINDCDC1 = 3.5 V
160
180
VINDCDC1 = 6.3 V
ILL
Low side MOSFET leakage current
VDS = 6.3 V
ILIMF
Forward current limit
for TPS65072, TPS65073, TPS650731,
TPS650732
ILIMF
Forward current limit
for TPS65070
fS
Oscillator frequency
Vout
Fixed output voltage range
0.8
Internal resistor divider, I2C selectable
1.1
mA
mΩ
1
mA
1.5
A
1.1
1.6
2.2
A
1.95
2.35
2.55
MHz
3.3
V
0.725
For TPS65070, TPS65072
3.3
For TPS65073, TPS650731, TPS650732
1.8
Vout
Default output voltage
Vout
DC output voltage accuracy; PFM mode (1)
VINDCDC1 = VDCDC1 +0.3 V to 6.3 V;
0 mA ≤ IO ≤ 0.6 A
–2%
3%
Vout
DC output voltage accuracy; PWM mode (1)
VINDCDC1 = VDCDC1 +0.3 V to 6.3 V;
0 mA ≤ IO ≤ 0.6 A
–1.5%
1.5%
ΔVOUT
Power save mode ripple voltage (2)
IOUT = 1 mA, PFM mode
tStart
Start-up time
Time from active EN to Start switching
tRamp
VOUT ramp up time
(2)
mΩ
2
Low side MOSFET on-resistance
(1)
V
600
RDS(ON)
RDIS
UNIT
6.3
V
40
mVpp
170
ms
Time to ramp from 5% to 95% of VOUT
250
ms
power good threshold
rising voltage
Vo 5%
power good threshold
falling voltage
Vo 10%
Internal discharge resistor at L1
–35%
250
Ω
35%
Output voltage specification does not include tolerance of external voltage programming resistors. Output voltage in PFM mode is
scaled to +1% of nominal value.
Configuration L= 2.2 mH, COUT = 10 mF
DCDC2 CONVERTER
PARAMETER
VVINDCDC
TEST CONDITIONS
Input voltage range
Connected to SYS pin
MIN TYP
2.8
MAX
6.3
UNIT
V
2
IO
Maximum output current
RDS(ON)
High side MOSFET on-resistance
ILH
High side MOSFET leakage current
RDS(ON)
Low side MOSFET on-resistance
ILL
Low side MOSFET leakage current
ILIMF
Forward current limit
fS
Oscillator frequency
Vout
Adjustable output voltage range
Vref
Reference voltage
Vout
Fixed output voltage range
TPS65072/73/731/732
TPS65070
600
Vin > 2.8 V
mA
1500
VINDCDC2 = 2.8 V
150
300
VINDCDC2 = 3.5 V
120
200
VINDCDC2 = 2.8 V
200
300
VINDCDC2 = 3.5 V
160
180
0.8
1.1
1.5
2.1
2.4
3.5
1.95 2.35
2.55
VINDCDC2 = 6.3 V
2
VDS = 6.3 V
TPS65072/73/731/732
TPS65070
1
2.8 V < VINDCDC2 < 6.3 V
External resistor divider
0.6
Vin
600
Copyright © 2011, Texas Instruments Incorporated
Internal resistor divider, I2C
selectable (Default setting)
0.725
mA
mΩ
mA
A
MHz
V
mV
3.3
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
mΩ
V
5
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
DCDC2 CONVERTER (continued)
PARAMETER
TEST CONDITIONS
Default output voltage for TPS65070, TPS650732
Vout
Default output voltage for TPS65072
Default output voltage for TPS65073, TPS650731
DC output voltage accuracy; PFM mode
DC output voltage accuracy; PWM mode
Vout
1.8
For DEFDCDC2 = HIGH
3.3
For DEFDCDC2 = LOW
1.8
For DEFDCDC2 = HIGH
2.5
For DEFDCDC2 = LOW
1.2
For DEFDCDC2 = HIGH
(1)
VINDCDC2 = 2.8 V to 6.3 V;
0 mA ≤ IO ≤ 1.5 A
DC output voltage accuracy with resistor divider at DEFDCDC2; PWM
VINDCDC2 = VDCDC2 +0.3 V (min
2.8 V) to 6.3 V; 0 mA ≤ IO ≤ 1.5A
Power save mode ripple voltage
IOUT = 1 mA, PFM mode (2)
tStart
tRamp
RDIS
(1)
(2)
MAX
UNIT
V
1.8
(1)
DC output voltage accuracy with resistor divider at DEFDCDC2; PFM
ΔVOUT
MIN TYP
For DEFDCDC2 = LOW
–2%
3%
–1.5
%
1.5%
–2%
3%
–1%
1%
40
mVpp
Start-up time
Time from active EN to Start
switching
170
ms
VOUT ramp up time
Time to ramp from 5% to 95% of
VOUT
250
ms
power good threshold
rising voltage
Vo 5%
power good threshold
falling voltage
Vo 10%
Internal discharge resistor at L2
–35%
250
35%
Ω
Output voltage specification does not include tolerance of external voltage programming resistors. Output voltage in PFM mode is
scaled to +1% of nominal value.
Configuration L= 2.2 mH, COUT = 10 mF
DCDC3 CONVERTER
PARAMETER
VVINDCDC
TEST CONDITIONS
Input voltage range
MIN
Connected to SYS pin
TYP
2.8
MAX
6.3
UNIT
V
3
TPS65072
IO
Maximum output current
RDS(ON)
High side MOSFET on-resistance
ILH
High side MOSFET leakage current
RDS(ON)
Low side MOSFET on-resistance
ILL
Low side MOSFET leakage current
ILIMF
Forward current limit
fS
Oscillator frequency
Vout
Adjustable output voltage range
Vref
Reference voltage
Vout
Fixed output voltage range
TPS65070, TPS65073, TPS650731,
TPS650732
(1)
6
VINDCDC3 = 2.8 V
150
300
VINDCDC3 = 3.5 V
120
200
VINDCDC3 = 2.8 V
200
300
VINDCDC3 = 3.5 V
160
180
0.8
1.1
1.5
2.1
2.4
3.5
1.95
2.35
2.55
2
VDS = 6.3 V
TPS65072
TPS65070/73/731/732
1
2.8 V < VINDCDC3 < 6.3 V
External resistor divider
0.6
Vin
600
Internal resistor divider, I2C
selectable (Default setting)
Default output voltage for TPS65072
Default output voltage for TPS65073, TPS650731, TPS650732
Vout
mA
1500
VINDCDC3 = 6.3 V
Default output voltage for TPS65070
Vout
600
Vin > 2.8 V
DC output voltage accuracy; PFM mode
DC output voltage accuracy; PWM mode
(1)
(1)
0.725
1.0
For DEFDCDC3 = HIGH
1.2
For DEFDCDC3 = LOW
1.2
For DEFDCDC3 = HIGH
1.4
For DEFDCDC3 = LOW
1.2
For DEFDCDC3 = HIGH
1.35
VINDCDC3 = 2.8 V to 6.3 V;
0 mA ≤ IO ≤ 1.5 A
mA
mΩ
mA
A
MHz
V
mV
3.3
For DEFDCDC3 = LOW
mΩ
V
V
–2%
3%
–1.5%
1.5%
Output voltage specification does not include tolerance of external voltage programming resistors. Output voltage in PFM mode is
scaled to +1% of nominal value.
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
DCDC3 CONVERTER (continued)
PARAMETER
TEST CONDITIONS
MIN
DC output voltage accuracy with resistor divider at DEFDCDC3; PWM
VINDCDC3 = VDCDC3 +0.3 V (min
2.8 V) to 6.3 V; 0 mA ≤ IO ≤ 1.5A
–2%
ΔVOUT
Power save mode ripple voltage
IOUT = 1 mA, PFM mode (2)
tStart
Start-up time
tRamp
Vout
DC output voltage accuracy with resistor divider at DEFDCDC3; PFM
Vout
RDIS
(2)
TYP
MAX
UNIT
3%
–1%
1%
40
mVpp
Time from active EN to Start
switching
170
ms
VOUT ramp up time
Time to ramp from 5% to 95% of
VOUT
250
ms
power good threshold
rising voltage
Vo 5%
power good threshold
falling voltage
Vo 10%
Internal discharge resistor at L3
–35%
250
35%
Ω
Configuration L= 2.2 mH, COUT = 10 mF
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
7
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
VLDO1 and VLDO2 LOW DROPOUT REGULATORS
MAX
UNIT
VINLDO
Input voltage range for LDO1, LDO2
PARAMETER
1.8
6.3 (1)
V
VLDO1
LDO1 output voltage range
1.0
3.3
V
VLDO2
LDO2 output voltage range
0.725
3.3
V
IO
Output current for LDO1
200
mA
VLDO1
LDO1 default output voltage
VLDO2
LDO2 default output voltage
TEST CONDITIONS
MIN
Voltage options available see register description
TYP
For TPS65072
1.2
For TPS65070, TPS65073, TPS650731, TPS650732
1.8
For TPS65070
1.2
For TPS65072
1.2
For TPS65073, TPS650731, TPS650732
1.8
V
V
IO
Output current for LDO2
200
mA
ISC
LDO1 short circuit current limit
VLDO1 = GND
400
mA
ISC
LDO2 short circuit current limit
VLDO2 = GND
400
mA
Minimum voltage drop at LDO1
IO = 100 mA, VINLDO = 3.3 V
150
mV
Minimum voltage drop at LDO2
IO = 100 mA, VINLDO = 3.3 V
150
mV
Output voltage accuracy for LDO1, LDO2
ILDO1 = 100 mA; ILDO2 = 100 mA;
Vin ≥ Vout + 200 mV
–1%
1.5%
Line regulation for LDO1, LDO2
VINLDO1,2 = VLDO1,2 + 0.5 V (min. 2.8 V) to 6.5 V,
ILDO1 = 100 mA; ILDO2 = 100 mA
–1%
1%
Load regulation for LDO1, LDO2
IO = 1 mA to 200 mA
Load regulation for LDO1, LDO2
IO < 1 mA ; Vo < 1V
RDIS
Internal discharge resistor at VLDO1, VLDO2
tRamp
VOUT ramp up time
(1)
8
–1%
1%
–2.5%
2.5%
Time to ramp from 5% to 95% of VOUT
400
Ω
250
ms
6.3 V or VSYS whichever is less
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
wLED BOOST CONVERTER
PARAMETER
VL4
voltage at L4 pin
Vsink1,2
Input voltage at ISINK1, ISINK2 pins
VOUT
Internal overvoltage protection
TEST CONDITIONS
MIN
Maximum boost factor (Vout/Vin)
Tmin_off
Minimum off pulse width
RDS(ON)
N-channel MOSFET on-resistance
Isink1 = Isink2 = 20 mA, Vin = 2.8 V
N-channel leakage current
35
37
9
10
0.8
Minimum voltage drop at Isink pin to GND for
proper regulation
VISET
ISET pin voltage
KISET
Isink1, Isink2
fPWM
Current multiple Iout/Iset
1.6
VDS = 25 V, TA = 25°C
V
16
V
39
V
ns
Ω
2.0
A
1
mA
1.125
MHz
400
mV
1.24
V
Iset current = 15 mA
1000
Iset current = 25 mA
1000
Minimum current into ISINK1, ISINK2 pins
For proper dimming (string can be disabled also)
Maximum current into ISINK1, ISINK2 pins
Vin = 3.3 V
DC current set accuracy
Isinkx = 5 mA to 25 mA; no PWM dimming
±5%
Current difference between Isink1 and isink2
Rset1 = 50k; Isink1 = 25 mA, Vin = 3.6 V; no PWM
dimming
±5%
Current difference between Isink1 and Isink2
Rset2 = 250k; Isink1 = 5 mA, Vin = 3.6 V; no PWM
dimming
±5%
PWM dimming frequency
Rise / fall time of PWM signal
4
25
–15%
100
15%
PWM dimming Bit = 01 (default)
–15%
200
15%
PWM dimming Bit = 10
–15%
500
15%
PWM dimming Bit = 11
–15%
1000
15%
2
Dimming PWM DAC resolution
mA
mA
PWM dimming Bit = 00
For all PWM frequencies
UNIT
39
0.6
Switching frequency
Vsink1,
Vsink2
MAX
70
VL4 = 3.6 V
N-channel MOSFET current limit
ILN_NFET
TYP
2.8
Hz
ms
1%
Reset, PB_IN, PB_OUT, PGood, Power_on, INT, EN_EXTLDO, EN_wLED
PARAMETER
Reset delay time and PGOOD delay time
TEST CONDITIONS
Input voltage at threshold pin rising; time
defined with <PGOOD DELAY0>, <PGOOD
DELAY1>
PB-IN debounce time
PB_IN “Reset-detect- time”
Internal timer
PGOOD low time when PB_IN = Low for >15s
MIN
TYP
MAX
–15%
20
100 (1)
200
400
15%
UNIT
–15%
50
15%
–15%
15
15%
s
–15%
0.5
15%
ms
ms
ms
VIH
High level input voltage on pin POWER_ON
1.2
VIN
V
VIH
High level input voltage on pin PB_IN
1.8
AVDD6
V
VIL
Low Level Input Voltage, PB_IN, Power_on
0
0.4
Internal pull-up resistor from PB_IN to AVDD6
50
Output current at AVDD6
IIN
Input bias current at Power_on
0.01
VOL
Reset, PB_OUT, PGood, INT output low voltage,
EN_EXTLDO
IOL = 1 mA, Vthreshold < 1 V
VOH
EN_EXTLDO HIGH level output voltage
IOH = 0.1 mA; optional push pull output
IOL
Reset, PB_OUT, PGood, INT sink current
mA
mA
0.3
V
VSYS
Reset, PB_OUT, PGood, INT open drain
output in high impedance state
Vth
Threshold voltage at THRESHOLD pin
Input voltage falling
Vth_hyst
Hysteresis on THRESHOLD pin
Input voltage rising
Iin
Input bias current at EN_wLED, THRESHOLD
(1)
1
1.0
1
Reset, PB_OUT, PGood,INT output leakage current
1
V
mA
0.25
–4%
V
kΩ
4%
7
mA
V
mV
1
mA
Default Reset delay time is set to 100 ms typical
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
9
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
ADC CONVERTER
PARAMETER
VIN
TEST CONDITIONS
MIN
TYP
MAX
Input voltage range at AD_IN1 to AD_IN4 pin
(channel 0 to channel 3)
For full scale measurement
0
2.25
Input voltage range internal channel 6 to channel 9
For full scale measurement
0
6
Input voltage range on channel4 (TS pin) and channel5
(ISET pin)
Unipolar measurement of charge current at pin
ISET (voltage at ISET)
0
2.25
4
UNIT
V
Iin
AD_IN1 to AD_IN4 input current
0.1
Cin
Input capacitance at AD_IN1 to AD_IN4
15
pF
ADC resolution
10
Bits
Differential linearity error
±1
mA
LSB
Offset error
1
Gain error
±8
LSB
220
ms
Sampling time
Conversion time
5
19
Wait time after enable
Time needed to stabilize the internal voltages
Quiescent current, ADC enabled by I2C
includes current needed for I2C block
ms
1.5
ms
500
mA
Quiescent current, conversion ongoing
1
Reference voltage output on pin BYPASS
–1%
LSB
2.260
Output current on reference output pin BYPASS
mA
1%
V
0.1
mA
TOUCH SCREEN INTERFACE
PARAMETER
VTSREF
TEST CONDITIONS
MIN
Voltage at internal voltage regulator for TSC
TYP
MAX
2.30
UNIT
V
TOUCHSCREEN PANEL SPECIFICATIONS
Plate resistance X
Specified by design
200
400
1200
Ω
Plate resistance Y
Specified by design
200
400
1200
Ω
Resistance between plates contact
180
400
1000
Ω
Resistance between plates pressure
180
400
1000
Position measurement; 400 Ω, 100 pF
Settling time
5.5
Capacitance between plates
2
10
100
pF
20.9
22
23.1
kΩ
111
160
Total capacitance at pins TSX1,TSX2,TSY1,TSY2 to GND
internal TSC reference resistance
Ω
ms
nF
SWITCH MATRIX SPECIFICATIONS
Tgate resistance
Specified by design
230
Ω
PMOS resistance
Specified by design
20
Ω
NMOS resistance
Specified by design
20
Ω
Quiescent supply current
in TSC standby mode with TSC_M[2..0] =
101
10
mA
POWER PATH
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
QUIESCENT CURRENT
IQSPP1
Quiescent current, AC or USB mode
Current into AC or USB, AC or USB selected,
no load at SYS
20
mA
INPUT SUPPLY
VBATMIN
Minimum battery voltage for BAT SWITCH
operation
No input power, BAT_SWITCH on
2.75
V
VIN(DT)
Input voltage detection threshold
AC detected when V(AC)–V(BAT) > VIN(DT) ;
USB detected when
V(USB)–V(BAT) > VIN(DT)
150
mV
VIN(NDT)
Input Voltage removal threshold
AC not detected when V(AC)–V(BAT) <
VIN(NDT) ; USB not detected when
V(USB)–V(BAT) < VIN(NDT)
IDISCH
Internal discharge current at AC and USB input
Activated based on settings in CHGCONFIG3
Bit 0 and Bit 7
10
Submit Documentation Feedback
75
95
mV
mA
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
POWER PATH (continued)
PARAMETER
TDGL(DT)
Power detected deglitch
VIN(OVP)
Input over voltage detection threshold
TEST CONDITIONS
MIN
TYP
AC or USB voltage increasing
MAX
22.5
5.8
6
UNIT
ms
6.3
V
POWER PATH TIMING
TSW(ACBAT)
Switching from AC to BAT
No USB, AC power removed
200
ms
SW(USBBAT)
T Switching from USB to BAT
No AC, USB power removed
200
ms
TSW(PSEL)
Switching from USB to AC
I2C
150
ms
TSW(ACUSB)
Switching from AC/ USB, USB / AC
AC power removed or USB power removed
200
ms
SYS power up delay
Measured from power applied to start of
power-up sequence
TSYSOK
11
ms
POWER PATH INTEGRATED MOSFETS CHARACTERISTICS
AC Input switch dropout voltage
(ILIMITAC set = 2.5 A I(SYS) = 1 A)
150
mV
USB input switch dropout voltage
ILIMITUSB = 1300 mA I(SYS) = 500 mA
ILIMITUSB = 1300 mA I(SYS) = 800 mA
100
160
mV
Battery switch dropout voltage
V(BAT) = 3.0 V, I(BAT) = 1 A
85
100
mV
Input Current Limit
IUSB100
Input current limit; USB pin
USB input current [0,0]
90
100
mA
IUSB500
Input current limit; USB pin
USB input current [0,1] (default)
450
500
mA
IUSB800
Input current limit; USB pin
USB input current [1,0]
700
800
mA
IUSB1300
Input current limit; USB pin
USB input current [1,1]
1000
1300
mA
IAC100
Input current limit; AC pin
AC input current [0,0]
90
100
mA
IAC500
Input current limit; AC pin
AC input current [0,1]
450
500
mA
IA1300
Input current limit; AC pin
AC input current [1,0]
1000
1300
mA
IAC2500
Input current limit; AC pin
AC input current [1,1] (default)
2000
2500
mA
POWER PATH SUPPLEMENT DETECTION PROTECTION AND RECOVERY FUNCTIONS
VBSUP1
Enter battery supplement mode
VBSUP2
Exit battery supplement mode
VSYS(SC1)
Sys short-circuit detection threshold, power-on
VOUT ≤ VBAT –
45 mV
AC input current set to 10: 1.3A
VOUT ≥ VBAT –
35 mV
All power path switches set to OFF if V VSYS <
VSYS(SC1)
1.4
Short circuit detection threshold hysteresis
RFLT(AC)
Sys Short circuit recovery pull-up resistors
Internal resistor connected from AC to SYS;
Specified by design
RFLT(USB)
Sys Short circuit recovery pull-up resistors
Internal resistor connected from USB to SYS;
Specified by design
VSYS(SC2)
Output short-circuit detection threshold, supplement
mode VBAT – VSYS > VO(SC2) indicates short-circuit
tDGL(SC2)
Deglitch time, supplement mode short circuit
tREC(SC2)
Recovery time, supplement mode short circuit
VBAT(SC)
BAT pin short-circuit detection threshold
IBAT(SC)
Source current for BAT pin short-circuit detection
200
1.8
2.0
V
50
mV
500
Ω
500
Ω
250
300
mV
120
ms
60
ms
1.4
1.8
2.0
V
4
7.5
11
mA
DPPM LOOP (1)
VDPM
(1)
Threshold at which DPPM loop is enabled. This is
the approximate voltage at SYS pin, when the USB
or AC switch reaches current limit and the charging
current is reduced; Selectable by I2C
3.5
3.75
4.25
4.50
Set with Bits
<PowerPath DPPM threshold1>;
<PowerPath DPPM threshold0>
V
If the DPPM threshold is lower than the battery voltage, supplement mode will be engaged first and the SYS voltage will chatter around
the battery voltage; during that condition no DPPM mode is available.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
11
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
BATTERY CHARGER
(1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
–1%
4.10
1%
–1%
4.15
1%
–1%
4.20
1%
–1%
4.25
1%
UNIT
CHARGER SECTION
Battery discharge current
2
Battery charger voltage
Depending on setting in CHGCONFIG2
And internal EEPROM
Default = 4.20V
VLOWV
Pre-charge to fast-charge transition threshold
default = 2.9 V set with
Bit <Precharge Voltage>
tDGL1(LOWV)
Vo(BATREG)
A
V
2.9
2.5
V
Deglitch time on pre-charge to fast-charge
transition
25
ms
tDGL2(LOWV)
Deglitch time on fast-charge to pre-charge
transition
25
ms
ICHG
Battery fast charge current range
VBAT(REG) > VBAT > VLOWV, VIN = VAC or VUSB =
5V
ICHG
Battery fast charge current
VBAT > VLOWV, VIN = 5 V, IIN-MAX > ICHG, no
load on SYS pin, thermal loop not active,
DPPM loop not active
KISET
Fast charge current factor
for a charge current of 1500 mA
840
900
1000
AΩ
KISET
Fast charge current factor
for a charge current of 100 mA
930
1100
1200
AΩ
0.1×
ICHG
0.12×
ICHG
A
0.13×
ICHG
A
100
1500
KISET/RISET
IPRECHG
Pre-charge current
0.08×
ICHG
ITERM
Charge current value for termination detection
threshold (internally set)
0.08×
ICHG
0.1×
ICHG
tDGL(TERM)
Deglitch time, termination detected
VRCH
Recharge detection threshold
150
100
tDGL(RCH)
Deglitch time, recharge threshold detected
tDGL(NO-IN)
Delay time, input power loss to charger turn-off
IBAT(DET)
Sink current for battery detection
tDET
Battery detection timer
A
25
Voltage below nominal charger voltage
VBAT = 3.6V. Time measured from
VIN: 5V → 3.3V 1ms fall-time
ms
65
ms
20
ms
10
250
TCHG
Charge safety timer
TPRECHG
Precharge timer
Pre charge timer range, thermal and
DPM/DPPM loops not active scalable with
<Precharge Time>
TPCHGADD
Pre-charge safety timer “add-on” time range
Maximum value for pre-charge safety timer,
thermal, DPM or DPPM loops always active
mV
125
3
Safety timer range, thermal and DPM not
active selectable by I2C with Bits
<ChargeSafetyTimerValue1>
<ChargeSafetyTimerValue0>
mA
ms
–15%
4
5
6
8
15%
25
50
30
60
35
70
0
mA
2×TCHG
h
min
h
BATTERY-PACK NTC MONITOR
RT1
Pull-up resistor from thermistor to Internal LDO .
I2C selectable
10 k curve 2 NTC
–2%
7.35
2%
100 k curve 1 NTC
–2%
62.5
2%
VHOT
High temperature trip point (set to 45°C)
Battery charging
VHYS(HOT)
Hysteresis on high trip point (set to 3°C)
VCOLD
Low temperature trip point (set to 0°C)
VHYS(COLD)
kΩ
kΩ
860
mV
Battery charging
50
mV
Battery charging
1660
mV
Hysteresis on low trip point (set to 3°C)
Battery charging
50
mV
VnoNTC
No NTC detected
NTC error
2000
mV
THRMDLY
Deglitch time for thermistor detection after
thermistor power on
tDGL(TS)
Deglitch time, pack temperature fault detection
(1)
12
3
Battery charging
ms
50
ms
The Battery Charger is DISABLED by default
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
BATTERY CHARGER (1) (continued)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
115
125
135
°C
THERMAL REGULATION
If temperature is exceeded, charge current is
reduced
TJ(REG)
Temperature regulation limit
TJ(OFF)
Charger thermal shutdown
TJ(OFF-HYS)
Charger thermal shutdown hysteresis
155
°C
20
°C
DEVICE INFORMATION
PIN ASSIGNMENT (TOP VIEW)
30
PGND3
SYS
8
29
VDCDC3
ISET
9
28
SCLK
AC
10
27
SDAT
TS
11
26
PGOOD
USB
12
25
PB_IN
21
22
23
24
VINDCDC1/2
L2
VDCDC2
PB_OUT
19
20
L1
DEFDCDC2
VDCDC1
17
18
DEFDCDC3
15
16
EN_DCDC2
EN_DCDC1
EN_DCDC3
13
14
POWER_ON
POWER PAD
AGND
BYPASS
INT
RESET
FB_WLED
L4
42
41
40
39
38
37
AD_IN2 (TSX2)
AD_IN1 (TSX1)
44
43
AD_IN4 (TSY2)
AD_IN3 (TSY1)
46
45
INT_LDO
THRESHOLD
48
47
31
L3
SYS
7
30
PGND3
SYS
8
29
VDCDC3
ISET
9
28
SCLK
AC
10
27
SDAT
TS
11
26
PGOOD
USB
12
25
PB_IN
POWER PAD
24
7
6
PB_OUT
SYS
VIN_DCDC3
BAT
23
L3
VDCDC2
31
32
22
6
5
21
BAT
ISINK2
BAT
L2
VIN_DCDC3
VINDCDC1/2
32
33
19
5
4
20
BAT
ISINK1
VLDO1
L1
ISINK2
VDCDC1
33
34
17
4
3
18
VLDO1
ISET1
VINLDO1/2
DEFDCDC2
ISINK1
ISET2
35
DEFDCDC3
34
36
2
15
3
1
16
VINLDO1/2
AVDD6
VLDO2
EN_DCDC2
ISET1
EN_DCDC3
ISET2
35
13
36
2
14
1
EN_DCDC1
L4
37
AVDD6
VLDO2
POWER_ON
EN_EXTLDO
FB_WLED
38
INT
40
39
AGND
BYPASS
41
TPS65070, TPS65073, TPS650731, TPS650732
42
AD_IN2
AD_IN1
44
43
AD_IN4
AD_IN3
46
45
INT_LDO
EN_wLED
48
47
TPS65072
PIN FUNCTIONS
PIN
NAME
NO.
I/O
DESCRIPTION
CHARGER BLOCK:
AC
10
I
Input power for power path manager, connect to external DC supply. Connect external 1mF (minimum) to
GND
USB
12
I
Input power for power path manager, connect to external voltage from a USB port. Connect external 1mF
(minimum) to GND. Default input current limit is 500 mA max
BAT
5,6
O
Charger power stage output, connect to battery. Place a ceramic capacitor of 10mF from these pins to GND
1
O
Internal “always-on”-voltage. Connect a 4.7mF cap from AVDD6 to GND
SYS
7, 8
O
System voltage; output of the power path manager. All voltage regulators are typically powered from this
output.
TS
11
I
Temperature sense input. Connect to NTC thermistor to sense battery pack temperature. TPS6507x can be
internally programmed to operate with a 10k curve 2 or 100k curve 1 thermistor. To linearize the thermistor
response, use a 75k (for the 10k NTC) or a 360k (for the 100k NTC) in parallel with the thermistor. Default
setting is 10k NTC
ISET
9
I
Connect a resistor from ISET to GND to set the charge current.
SCLK
28
I
Clock input for the I2C interface.
SDAT
27
AD_IN1
(TSX1)
43
AVDD6
I/O Data line for the I2C interface.
I
Analog input1 for A/D converter TPS65070, TPS65073, TPS650731, TPS650732 only:
Input 1 to the x-plate for the touch screen.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
13
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
PIN FUNCTIONS (continued)
PIN
I/O
DESCRIPTION
NAME
NO.
AD_IN2
(TSX2)
44
I
Analog input2 for A/D converter TPS65070, TPS65073, TPS650731, TPS650732 only:
Input 2 to the x-plate for the touch screen
AD_IN3
(TSY1)
45
I
Analog input3 for A/D converter TPS65070, TPS65073, TPS650731, TPS650732 only:
Input 1 to the y-plate for the touch screen
AD_IN4
(TSY2)
46
I
Analog input4 for A/D converter TPS65070, TPS65073, TPS650731, TPS650732 only:
Input 2 to the y-plate for the touch screen
BYPASS
41
O
Connect a 10mF bypass cap from this pin to GND. This pin can optionally be used as a reference output
(2.26 V). The maximum load on this pin is 0.1mA.
INT_LDO
48
O
Connect a 2.2mF bypass cap from this pin to GND. The pin is connected to an internal LDO providing the
power for the touch screen controller (TSREF).
O
Open drain interrupt output. An interrupt can be generated upon:
• A touch of the touch screen
• Voltage applied or removed at pins AC or USB
• PB_IN actively pulled low (optionally actively pulled high)
INT
40
The output is actively pulled low if the interrupt is active. The output goes high after the Bit causing the
interrupt in register INT has been read. The interrupt sources can be masked in register INT, so no interrupt
is generated and pin INT is pulled high with its external pull-up resistor.
CONVERTERS:
VINDCDC1/2
21
I
Input voltage for DCDC1 and DCDC2 step-down converter. This pin must be connected to the SYS pin.
VDCDC1
19
I
Feedback voltage sense input. For the fixed voltage option, this pin must directly be connected to Vout1, for
the adjustable version, this pin is connected to an external resistor divider.
L1
20
O
Switch Pin for DCDC1. Connect to Inductor
EN_DCDC1
14
I
Enable Input for DCDC1, active high
VDCDC2
23
I
Feedback voltage sense input, connect directly to Vout2
DEFDCDC2
18
I
Select Pin of DCDC2 output voltage.
L2
22
O
Switch Pin of DCDC2. Connect to Inductor.
EN_DCDC2
15
I
Enable Input for DCDC2, active high
VINDCDC3
32
I
Input voltage for DCDC3 step-down converter. This pin must be connected to the SYS pin.
VDCDC3
29
I
Feedback voltage sense input, connect directly to Vout3
DEFDCDC3
17
I
Select Pin of DCDC3 output voltage.
L3
31
O
Switch Pin of DCDC3. Connect to Inductor.
EN_DCDC3
16
I
Enable Input for DCDC3, active high
PGND3
30
AGND
42
VINLDO1/2
3
I
Input voltage for LDO1 and LDO2
VLDO1
4
O
Output voltage of LDO1
VLDO2
2
O
Output voltage of LDO2
L4
37
I
Switch Pin of the white LED (wLED) boost converter. Connect to Inductor and rectifier diode.
FB_wLED
38
I
Feedback input for the boost converter's output voltage.
Iset1
(AD_IN6)
35
I
Connect a resistor from this pin to GND to set the full scale current for Isink1 and Isink2 with Bit Current
Level in register WLED_CTRL0 set to 1.
Analog input6 for the A/D converter.
Iset2
(AD_IN7)
36
I
Connect a resistor from this pin to GND to set the full scale current for Isink1 and Isink2 with Bit Current
Level in register WLED_CTRL0 set to 0.
Analog input7 for the A/D converter.
Isink1
34
I
Input to the current sink 1. Connect the cathode of the LEDs to this pin.
Isink2
33
I
Input to the current sink 2. Connect the cathode of the LEDs to this pin.
PB_IN
25
I
Enable input for TPS6507x. When pulled LOW, the DCDC converters and LDOs start with the sequencing
as programmed internally. Internal 50kΩ pull-up resistor to AVDD6
14
Power GND for DCDC3. Connect to PGND (PowerPAD)
Analog GND, connect to PGND (PowerPAD)
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
PIN FUNCTIONS (continued)
PIN
NAME
NO.
I/O
DESCRIPTION
POWER_ON
13
I
Power_ON input for the internal state machine. After PB_IN was pulled LOW to turn on the TPS6507x, the
POWER_ON pin needs to be pulled HIGH by the application processor to keep the system in ON-state
when PB_IN is released HIGH. If POWER_ON is released LOW, the DCDC converters and LDOs will turn
off when PB_IN is HIGH.
PB_OUT
24
O
Open drain output. This pin is driven by the status of the /PB_IN input (after debounce). PB_OUT=LOW if
PB_IN=LOW
PGOOD
26
O
Open drain power good output. The delay time equals the setting for Reset. The pin will go low depending
on the setting in register PGOODMASK. Optionally it is also driven LOW for 0.5ms when PB_IN is pulled
LOW for >15s.
THRESHOLD
47
I
TPS65070, TPS65073, TPS650731, TPS650732:Input for the reset comparator. RESET will be LOW if this
voltage drops below 1V.
RESET
39
O
Open drain active low reset output, reset delay time. The status depends on the voltage applied at
THRESHOLD.
PowerPAD™
Power ground connection for the PMU. Connect to GND
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
15
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
Functional Block Diagram
AC
SYS
AC
switch
22 mF
SYS
USB
USB
switch
AVDD6
Iset
4.7 mF
Batt
BAT
switch
Charger/power path mgmt
Batt
TS
TSX1 TSX2
INT_LDO
AD_IN1
INTERNAL BIASING
Thermistor
biasing
Touch
screen
biasing
AD_IN2
BYPASS
AD_IN3
TSY1 TSY2
AD_IN4
AD_IN1
AD_IN2
AD_IN3
AD_IN4
V_TS
ANALOG MUX
I_Ch
V_AC
V_USB
AD_IN5
V_SYS
V_BAT_SNS
10 BIT SAR
ADC
SCLK
State
machine
I²C
SDAT
INT
Power_ON
PB_IN
PB_OUT
ON/OFF circuitry / power good logic
undervoltage lockout
PGOOD
2.2 mH
L1
VIN_DCDC1/2
DCDC1
STEP-DOWN CONVERTER
600mA
EN_DCDC1
VI/O
VDCDC1
10 mF
PGND1
2.2 mH
L2
DCDC2
STEP-DOWN CONVERTER
600mA / 1500mA
DEFDCDC2
EN_DCDC2
Vmem
VDCDC2
10 mF
PGND2/PAD
2.2 mH
L3
VIN_DCDC3
DCDC3
STEP-DOWN CONVERTER
DEFDCDC3
EN_DCDC3
Sequencing
600mA / 1500mA
10 mF
PGND3/PAD
VINLDO1/2
EN_LDO1(I2C)
Vcore
VDCDC3
VLDO1
LDO1
200mA LDO
VLDO1
2.2 mF
VLDO2
EN_LDO2(I2C)
VLDO2
LDO2
200mA LDO
2.2 mF
L4
SYS
FB_wLED
iset1
1 mF
wLED boost
I2C controlled
up to 25mA per string
iset2
Isink1
Isink2
THRESHOLD
PGND4/PAD
(EN_wLED)
Reset
-
(EN_EXTLDO )
delay
+
Vref =1V
AGND
16
Submit Documentation Feedback
PGND(PAD)
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
PARAMETER MEASUREMENT INFORMATION
The data sheet graphs were taken on the evaluation module (EVM). Please refer to the EVM user´s guide
(SLVU291) for the setup information.
TYPICAL CHARACTERISTICS
TABLE OF GRAPHS
FIGURE
Efficiency DCDC1 vs Load current / PWM mode
VO = 3.3V; VI = 3.0V, 3.6V, 4.2V, 5V
1
Efficiency DCDC1 vs Load current / PFM mode
VO = 3.3V; VI = 3.0V, 3.6V, 4.2V, 5V
2
Efficiency DCDC2 vs Load current / PWM mode up to 1.5A
VO = 2.5V; VI = 3.0V, 3.6V, 4.2V, 5V
3
Efficiency DCDC2 vs Load current / PFM mode up to 1.5A
VO = 2.5V; VI = 3.0V, 3.6V, 4.2V, 5V
4
Efficiency DCDC2 vs Load current / PWM mode up to 1.5A
VO = 1.8V; VI = 3.0V, 3.6V, 4.2V, 5V
5
Efficiency DCDC2 vs Load current / PFM mode up to 1.5A
VO = 1.8V; VI = 3.0V, 3.6V, 4.2V, 5V
6
Efficiency DCDC3 vs Load current / PWM mode up to 1.5A
VO = 1.2V; VI = 3.0V, 3.6V, 4.2V, 5V
7
Efficiency DCDC3 vs Load current / PFM mode up to 1.5A
VO = 1.2V; VI = 3.0V, 3.6V, 4.2V, 5V
8
Efficiency DCDC3 vs Load current / PWM mode up to 1.5A
VO = 1.0V; VI = 3.0V, 3.6V, 4.2V, 5V
9
Efficiency DCDC3 vs Load current / PFM mode up to 1.5A
VO = 1.0V; VI = 3.0V, 3.6V, 4.2V, 5V
10
Load transient response converter 1
Scope plot; IO= 60mA to 540mA; VO = 3.3V; VI = 3.6V
11
Load transient response converter 2
Scope plot; IO= 150mA to 1350mA; VO = 1.8V; VI = 3.6V
12
Load transient response converter 3
Scope plot; IO= 150mA to 1350mA; VO = 1.2V; VI = 3.6V
13
Line transient response converter 1
Scope plot; VO= 3.3; VI = 3.6V to 5V to 3.6V; IO= 600mA
14
Line transient response converter 2
Scope plot; VO= 1.8; VI = 3.6V to 5V to 3.6V; IO = 600mA
15
Line transient response converter 3
Scope plot; VO = 1.2V; VI=3.6V to 5V to 3.6V; IO = 600mA
16
Output voltage ripple and inductor current converter 2;
PWM Mode
Scope plot; VI = 3.6V; VO=1.8V; IO = 10mA
17
Output voltage ripple and inductor current converter 2;
PFM Mode
Scope plot; VI = 3.6V; VO=1.8V; IO = 10mA
18
Startup DCDC1, DCDC2 and DCDC3, LDO1, LDO2
Scope plot
19
Load transient response LDO1
Scope plot; VO= 1.2V; VI=3.6V
20
Line transient response LDO1
Scope plot
21
KSET vs RISET
22
wLED efficiency vs duty cycle
2 x 6LEDs (VLED=19.2V); IO= 2x20mA
23
wLED efficiency vs input voltage
2 x 6LEDs (VLED=19.2V); IO= 2x20mA
24
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
17
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
EFFICIENCY DCDC1
vs
LOAD CURRENT/PWM MODE
EFFICIENCY DCDC1
vs
LOAD CURRENT/PFM MODE
100
3.4V
80
60
5V
50
40
60
50
40
30
30
20
20
10
10
100
90
0.001
0.01
0.1
IO - Output Current - A
1
VO = 3.3 V,
PWM Mode
25°C
0
0.0001
10
0.001
1
Figure 2.
EFFICIENCY DCDC2
vs
LOAD CURRENT/PWM MODE
EFFICIENCY DCDC2
vs
LOAD CURRENT/PFM MODE
10
100
VO = 2.5 V,
PWM Mode
25°C
3V
90
3V
80 3.6V
3.6V
4.2V
70
70
5V
60
Efficiency - %
4.2V
Efficiency - %
0.01
0.1
IO - Output Current - A
Figure 1.
80
5V
50
40
60
50
40
30
30
20
20
10
10
0
0.0001
0.001
0.01
0.1
IO - Output Current - A
Figure 3.
18
4.2V
70
4.2V
0
0.0001
5V 3.6V
80
3.6V
70
Efficiency - %
3.4V
90
Efficiency - %
90
100
VO = 3.3 V,
PWM Mode
25°C
Submit Documentation Feedback
1
10
0
0.0001
VO = 2.5 V,
PWM Mode
25°C
0.001
0.01
0.1
IO - Output Current - A
1
10
Figure 4.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
EFFICIENCY DCDC2
vs
LOAD CURRENT/PWM MODE
EFFICIENCY DCDC2
vs
LOAD CURRENT/PFM MODE
100
100
VO = 1.8 V,
90 PWM Mode
25°C
80
80
3V
60
4.2V
50
5V
40
20
10
10
0.01
0.1
IO - Output Current - A
1
0
0.0001
10
0.001
0.01
0.1
IO - Output Current - A
1
Figure 6.
EFFICIENCY DCDC3
vs
LOAD CURRENT/PWM MODE
EFFICIENCY DCDC3
vs
LOAD CURRENT/PFM MODE
70
VO = 1.2 V,
90 PWM Mode
25°C
80
3V
3V
70 3.6V
Efficiency - %
3.6V
60
4.2V
5V
40
40
20
20
10
10
Figure 7.
Copyright © 2011, Texas Instruments Incorporated
1
10
5V
50
30
0.01
0.1
IO - Output Current - A
4.2V
60
30
0.001
10
100
VO = 1.2 V,
90 PWM Mode
25°C
80
Efficiency - %
VO = 1.8 V,
PWM Mode
25°C
Figure 5.
100
0
0.0001
5V
40
20
50
4.2V
50
30
0.001
3.6V
60
30
0
0.0001
3V
70
3.6V
Efficiency - %
Efficiency - %
70
90
0
0.0001
0.001
0.01
0.1
IO - Output Current - A
1
10
Figure 8.
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
19
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
EFFICIENCY DCDC3
vs
LOAD CURRENT/PWM MODE
EFFICIENCY DCDC3
vs
LOAD CURRENT/PFM MODE
100
90
100
VO = 1 V,
PWM Mode
25°C
90
80
3.6V
70
70
3.6V
60
50
4.2V
Efficiency - %
Efficiency - %
3V
80
3V
5V
40
40
20
20
10
10
0.01
0.1
IO - Output Current - A
1
10
5V
50
30
0.001
4.2V
60
30
0
0.0001
0
0.0001
0.001
0.01
0.1
IO - Output Current - A
1
Figure 9.
Figure 10.
LOAD TRANSIENT RESPONSE
CONVERTER 1
LOAD TRANSIENT RESPONSE
CONVERTER 2
VOUT DCDC1 (Offset: 3.3 V)
10
VOUT DCDC2 (Offset: 1.8 V)
ILoad DCDC2
ILoad DCDC1
VIN DCDC3 = 3.6V,
Load = 60 mA - 560 mA - 60 mA
Figure 11.
20
VO = 1 V,
PWM Mode
25°C
Submit Documentation Feedback
VIN DCDC3 = 3.6 V,
Load mA - 1350 mA - 150 mA
Figure 12.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
LOAD TRANSIENT RESPONSE
CONVERTER 3
VOUT DCDC3 (Offset: 1.2 V)
LINE TRANSIENT RESPONSE
CONVERTER 1
VOUT DCDC1 (Offset: 3.25 V)
ILoad DCDC3
VIN DCDC1 (Offset: 3 V)
VIN = 3.6 V - 5 V - 3.6V,
Load = 0.6 A
VIN DCDC3 = 3.6 V,
Load = 150 mA - 1350 mA - 150 mA
Figure 13.
Figure 14.
LINE TRANSIENT RESPONSE
CONVERTER 2
LINE TRANSIENT RESPONSE
CONVERTER 3
VOUT DCDC2 (Offset: 1.75 V)
VOUT DCDC3 (Offset: 1.16 V)
VIN DCDC2 (Offset: 3 V)
VIN DCDC3 (Offset: 3 V)
VIN = 3.6 V - 5 V - 3.6V,
Load = 1.5 A
Figure 15.
Copyright © 2011, Texas Instruments Incorporated
VIN = 3.6 V - 5 V - 3.6V,
Load = 1.5 A
Figure 16.
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
21
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
OUTPUT VOLTAGE RIPPLE AND INDUCTOR CURRENT
CONVERTER 2 – PWM MODE
OUTPUT VOLTAGE RIPPLE AND INDUCTOR CURRENT
CONVERTER 2 – PFM MODE
VOUT DCDC2 (Offset: 1.8 V)
VOUT DCDC2 (Offset: 1.78 V)
IL DCDC2
IL DCDC2
VIN = 3.6 V,
Load = 200 mA PWM
VIN = 3.6 V,
Load = 15 mA PFM
Figure 17.
Figure 18.
STARTUP DCDC1, DCDC2, AND DCDC3,
LDO1, LDO2
LOAD TRANSIENT RESPONSE LDO1
VOUT DCDC1,
(LOAD: 100 mA)
VOUT LDO1 (Offset: 1.8 V)
VOUT DCDC2,
(LOAD: 100 mA)
Vbat = VIN LDO1 = 3.6 V,
LOAD = 20 mA - 180 mA
VOUT DCDC3 (LOAD: 100 mA)
LDO1 (LOAD: 50 mA)
VOUT LDO2 (LOAD: 50 mA)
VIN = 3.6 V
Figure 19.
22
Submit Documentation Feedback
ILOAD LDO1
Figure 20.
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
KSET
vs
RISET
LINE TRANSIENT RESPONSE LDO1
1200
1150
VOUT LDO1 (Offset: 1.8 V)
1100
Kset
Vbat = 5 V,
VIN LDO1: 3.6 V - 5 V - 3.6 V,
LOAD = 40 mA
VIN LDO1 (Offset: 3 V)
1050
1000
950
900
0.1
1
10
100
RIset - kW
Figure 21.
Figure 22.
wLED EFFICIENCY
vs
Duty Cycle
wLED EFFICIENCY
vs
Vin
100
100
2x6 LEDs
20 mA each
90
90
2x6 LEDs
20 mA each
100% duty cycle
5V
3V
70
60
50
40
50
40
20
20
10
10
10
20
30
40 50 60 70
Duty Cycle - %
Figure 23.
Copyright © 2011, Texas Instruments Incorporated
80
90 100
25% duty cycle
60
30
0
50% duty cycle
70
30
0
75% duty cycle
80
3.6V
wLED - Efficiency - %
wLED - Efficiency - %
80
0
2.8
3.2
3.6
4
4.4
4.8
5.2
VI - Input Voltage - V
5.6
6
Figure 24.
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
23
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
DETAILED DESCRIPTION
BATTERY CHARGER AND POWER PATH
The integrate a Li-ion linear charger and system power path management targeted at space-limited portable
applications. The power the system while simultaneously and independently charging the battery. This feature
reduces the number of charge and discharge cycles on the battery, allows for proper charge termination and
enables the system to run with a defective or absent battery pack. It also allows instant system turn-on even with
a totally discharged battery. The input power source for charging the battery and running the system can be an
AC adapter or an USB port. The power-path management feature automatically reduces the charging current if
the system load increases. The power-path architecture also permits the battery to supplement the system
current requirements when the adapter cannot deliver the peak system currents.
250 mV
AVDD6V
Vsys (sc1)
V BAT
SYS-SC1
SYS - SC2
t DGL(SC2)
500 W
AC
VSYS
I(AC)
VAC
ADC2
SYS
ADC0
AC SWITCH
V ISET
V IPRECHG
I(AC) / KILIMIT
ADC5
ISET
500
VI CHG
I(USB)
VUSB
ADC1
USB
I(USB)
IAC
T J(REG)
V DPPM
V OUT
I²C
IAC100
IAC500
DAC
Sys
V BAT(REG)
DUSBSWON
IAC1300
IAC2500
ISAMPLE
Short
Detect
USB SWITCH
DACSWON
IINLIM
I²C
IPRECHG
ITERM
TJ
AC Input
Current
Limit Error
Opamp
40 mV
VSYS
Supplement
IUSB100
IUSB500
IUSB800
IUSB1300
I²C
USB Input
Current
Limit Error
Opamp
IBAT(SC)
I²C
BAT
V LOWV
V
VRCH
V BAT(SC)
ADC3
BAT_sense
IUSB
I BAT (DET)
tDGL(TERM)
V BAT + V IN- DT
t DGL2( LOWV)
t DGL1( LOWV)
/VUSB
t DGL(RCH)
BAT - SC
VAC
DAC
I²C
t DGL(NO-IN)
t DGL(PGOOD)
V UVLO
I²C
V OVP
t BLK(OVP)
VTHRON
DTHCHG
Charge control
Half timers
I²C
I²C
V HOT(45)
Dynamically
controlled
Oscillator
Fast-charge timer
Pre-charge timer
V ISET
I²C
TS
t DGL(TS)
V IPRECHG
VI CHG
ADC4
Reset timers
Timers disabled
V COLD (0)
Timer fault
I²C
CC1 3
RST
CC1 0
V DIS(TS)
EN
I²C EN
Figure 25. Charger Block Diagram
24
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
POWER DOWN
The charger remains in a power down mode when the input voltage at the AC or USB pin is below the
under-voltage lockout threshold VUVLO. During the power down mode the host commands at the control pins are
not interpreted.
POWER-ON RESET
The charger resets when the input voltage at the AC or USB pin enters the valid range between VUVLO and
VOVLO. All internal timers and other circuit blocks are reset. The device then waits for a time period TDGL(PGOOD),
after which CHARGER ACTIVE Bit indicates the input power status, and the Iset pin is interpreted.
POWER-PATH MANAGEMENT
There are two inputs to the power path called AC and USB. Both inputs support the same voltage rating but are
typically set to a different current limit with AC beeing at the higher limit and USB at the lower. If voltage is
applied at both inputs and both are enabled in register PPATH1 (default setting), AC will be preferred over USB.
In this case, the deivce is only powered from AC and there is no current from USB. If voltage at AC is removed,
the USB input will become and is powered from USB. The current at the input pin AC or USB of the power path
manager is shared between charging the battery and powering the system load on the SYS pin. Priority is given
to the system load. The input current is monitored continuously. If the sum of the charging and system load
currents exceeds the preset maximum input current (programmed internally by I2C), the charging current is
reduced automatically. See the electrical characteristics or the register desciption for the default current limit on
AC and USB for the different family members.
Figure 26 illustrates what happens in an example case where the battery fast-charge current is set to 500mA, the
input current limit is set at 900mA and the system load varies from 0 to 750mA.
IOUT
400 mA
IBAT
750 mA
500 mA
150 mA
IIN
IIN -MAX
900 mA
500 mA
Figure 26. Power Path Functionality
SYS Output
The SYS pin is the output of the power path. When is turned off and there is no voltage at AC or USB, the SYS
output is disconnected internally from the battery. When is turned on by pulling PB_IN =LOW, the voltage at SYS
will ramp with a soft-start. During soft start, the voltage at SYS is ramped with a 30mA current source until the
voltage reached 1.8V. During the soft start, the SYS pin must not be loaded by an external load.
BATTERY CHARGING
When Bit CHARGER ENABLE in register CHGCONFIG1 is set to 1, battery charging can begin. First, the device
checks for a short-circuit on the BAT pin: IBAT(SC) is turned on till the voltage on the BAT pin rises above VBAT(SC).
If conditions are safe, it proceeds to charge the battery.
The battery is charged in three phases: conditioning pre-charge, constant current fast charge (current regulation)
and a constant voltage tapering-off (voltage regulation). In all charge phases, an internal control loop monitors
the IC junction temperature and reduces the charge current if the internal temperature threshold is exceeded.
Figure 27 shows what happens in each of the three phases:
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
25
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
PRECHARGE
CC FAST CHARGE
CV TAPER
DONE
VBAT(REG)
IO(CHG)
Battery Current
Battery
Voltage
VLOWV
TERM CURRENT = 1
I(PRECHG)
I(TERM)
Figure 27. Battery Charge
In the pre-charge phase, the battery is charged at a current of IPRECHG. The battery voltage starts rising. Once the
battery voltage crosses the VLOWV threshold, the battery is charged at a current of ICHG. The battery voltage
continues to rise. When the battery voltage reaches VBAT(REG), the battery is held at a constant value of VBAT(REG).
The battery current now decreases as the battery approaches full charge. When the battery current reaches
ITERM, the TERM CURRENT flag in register CHGCONFIG0 indicates charging done by going high.
Note that termination detection is disabled whenever the charge rate is reduced from the set point because of the
actions of the thermal loop, the DPM loop or the VIN-LOW loop.
The value of the fast-charge current is set by the resistor connected from the ISET pin to GND, and is given by
the equation
ICHG = KISET / RISET
(1)
(1)
RISET = KISET / ICHG
(2)
(2)
Note that if ICHG is programmed as greater than the input current limit, the battery will not charge at the rate of
ICHG, but at the slower rate of IIN-MAX (minus the load current on the OUT pin, if any). In this case, the charger
timers will be slowed down by 2x whenever the thermal loop or DPPM is active.
I-PRECHARGE:
The value for the pre-charge current is fixed to a factor of 0.1 of the fast charge current (full scale current)
programmed by the external resistor Rset
ITERM:
The value for the termination current threshold can be set in register CHGCONFIG3 using Bits TERMINATION
CURRENT FACTOR 0 and TERMINATION CURRENT FACTOR 1. The termination current is pre-set to a factor
of 0.1 of the fast charge current programmed by the external resistor Rset.
Battery Detection and Recharge:
Whenever the battery voltage falls below VRCH (Vset-100mV), a check is performed to see whether the battery
has been removed: current IBAT(DET) is pulled from the battery for a duration tDET. If the voltage on the BAT pin
remains above VLOWV, it indicates that the battery is still connected. If the charger is enabled by Bit CHARGER
ENABLE in register CHGCONFIG1 set to 1, the charger is turned on again to top up the battery.
26
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
If the BAT pin voltage falls below VLOWV in the battery detection test, it indicates that the battery has been
removed. The device then checks for battery insertion: it turns on FET Q2 and sources IPRECHG out of the BAT
pin for duration tDET. If the voltage does not rise above VRCH, it indicates that a battery has been inserted, and a
new charge cycle can begin. If, however, the voltage does rise above VRCH, it is possible that a fully charged
battery has been inserted. To check for this, IBAT(DET) is pulled from the battery for tDET: if the voltage falls below
VLOWV, a battery is not present. The device keeps looking for the presence of a battery.
Charge Termination On/Off:
Charge termination can be disabled by setting the Bit CHARGE TERMINATION ON/OFF in register
CHGCONFIG1 to logic high. When termination is disabled, the device goes through the pre-charge, fast-charge
and CV phases, then remains in the CV phase – the charger behaves like an LDO with an output voltage equal
to VBAT(REG), able to source current up to ICHG or IIN-MAX, whichever is lesser. Battery detection is not performed.
Timers:
The charger in has internal safety timers for the pre-charge and fast-charge phases to prevent potential damage
to either the battery or the system. The default values for the timers can be changed in registers CHGCONFIG1
and CHGCONFIG3. The timers can be disabled by clearing Bit SAFETY TIMERS ENABLE in register
CHGCONFIG1. (Note that the timers are disabled when termination is disabled: Bit CHARGE TERMINATION
ON/OFF in register CHGCONFIG1 =1).
Dynamic Timer Function:
The following events can reduce the charging current and increase the timer durations in the fast charge phase:
1. The system load current increases, and the DPPM loop reduces the available charging current
2. The input current is reduced because the input voltage has fallen to VIN-LOW
3. The device has entered thermal regulation because the IC junction temperature has exceeded TJ(REG)
In each of these events, the internal timers are slowed down proportionately to the reduction in charging current.
Note also that whenever any of these events occurs, termination detection is disabled.
A modified charge cycle with the thermal loop active is shown in Figure 28.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
27
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
PRECHARGE
THERMAL
REGULATION
CC FAST
CHARGE
CV TAPER
DONE
VO(REG)
IO(CHG)
Battery
Voltage
Battery
Current
V(LOWV)
TERM CURRENT = 1
I(PRECHG)
I(TERM)
IC junction
temperature, TJ
TJ(REG)
Figure 28. Thermal Loop
Timer Fault:
The following events generate a fault status:
1. If the battery voltage does not exceed VLOWV in time tPRECHG during pre-charging
2. If the battery current does not reach ITERM in time tMAXCH in fast charge (measured from beginning of fast
charge).
The fault status is indicated by Bits CHG TIMEOUT or PRECHG TIMEOUT in register CHGCONFIG0 set to 1.
BATTERY PACK TEMPERATURE MONITORING
The device has a TS pin that connects to the NTC resistor in the battery pack. During charging, if the resistance
of the NTC indicates that the battery is operating outside the limits of safe operation, charging is turned off. All
timers maintain their values. When the battery pack temperature returns to a safe value, charging is resumed,
and the timers are also turned back on.
Battery pack temperature sensing is disabled when termination is disabled and the voltage on the TS pin is
higher than VDIS(TS) (caused by absence of pack and thus absence of NTC).
The default for the NTC is defined in register CHGCONFIG1 with Bit SENSOR TYPE as a 10k curve 2 NTC. The
sensor can be changed to a 100k curve 1 NTC by setting the Bit to 0.
There needs to be a resistor in parallel to the NTC for linearization of the temperature curve. The value for the
resistor is given in the table below:
28
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
Sensor type
resistor value in parallel to the NTC
10K curve 2
75k
100k curve 1
360k
BATTERY CHARGER STATE DIAGRAM
Wait 1 ms after
EN_REF_CHG=1
At any state, exit and force
EN_CHG=0 && EN_SHRT=0 &&
DBATSINK=0.
TEMP_ERROR=0. Also register should be enabled.
Check Bat lowV
EN_CHG=0
EN_ISHRT = 1
BAT_SHRT_D = 1
When
TEMP_ERROR=1 || BAT_OVERI_D=1
|| (BAT_SHRT_D = 1 && EN_CHG=1)
Or when AC and USB are not
detected. Out of normal mode.
YES
Reset timers when Supplement mode
is detected. SUPLM_D=1. Per
customer request.
NO
Check Iset shrt
EN_CHG=0
Slower timers 2x when DPPM_ON=1
or TREG_ON = 1
EN_ISHRT=0
EN_ISETDET_D = 1
And wait 1ms
YES
ISET_SHRT_D = 1
TEMP_HOT = 0 && TEMP_COLD = 0 && TSHUT = 0
NO
suspend = 0
cont precharge timer
EN_ISETDET_D=0
PRCHF = 1
Reset precharge timer
HALT_PRECHARGE
EN_CHG=0
suspend = 1
Halt precharge timer
PRECHARGE
EN_CHG=1
DPRCHF=1
TEMP_HOT = 1 || TEMP_COLD = 1 || TSHUT=1
FAULT
NO
Timeout = 1
TEMP_HOT = 0 && TEMP_COLD = 0
&& TSHUT = 0
NO
PRCH_D = 1
YES
EN_CHG=0
suspend = 1
Halt safety timer
TEMP_HOT = 1 || TEMP_COLD = 1 || TSHUT=1
CC_CV_CHARGE
EN_CHG=1
DPRCHF=0
FAULT
Timeout = 1
PRCH_D = 1
YES
HALT_CC_CV_CHARGE
suspend = 0
cont safety timer
Clear precharge timer
Reset safetytimer
PRCHF = 0
NO
TAPER_D = 1
YES
Clear safety timer
EN_CHG=0
RECHARGE
EN_CHG=0
NO
RCH_D = 1
YES
EN_DCH=1 && DBATSINK = 1 for Tdet
Then release. EN_DCH returns to previous state.
BAT_SRHT_D = 1
YES
EN_ISHRT=1 for Tdet
Figure 29. Charger State Machine
DCDC CONVERTERS AND LDOs
OPERATION
The step down converters operate with typically 2.25MHz fixed frequency pulse width modulation (PWM) at
moderate to heavy load currents. At light load currents the converter automatically enters Power Save Mode and
operates in Pulse Frequency Modulation (PFM) .
During PWM operation the converter use a unique fast response voltage mode controller scheme with input
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
29
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
voltage feed-forward to achieve good line and load regulation allowing the use of small ceramic input and output
capacitors. At the beginning of each clock cycle initiated by the clock signal, the High Side MOSFET switch is
turned on. The current flows now from the input capacitor via the High Side MOSFET switch through the inductor
to the output capacitor and load. During this phase, the current ramps up until the PWM comparator trips and the
control logic will turn off the switch. The current limit comparator will also turn off the switch in case the current
limit of the High Side MOSFET switch is exceeded. After a dead time preventing shoot through current, the Low
Side MOSFET rectifier is turned on and the inductor current will ramp down. The current flows now from the
inductor to the output capacitor and to the load. It returns back to the inductor through the Low Side MOSFET
rectifier.
The next cycle will be initiated by the clock signal again turning off the Low Side MOSFET rectifier and turning on
the on the High Side MOSFET switch.
The DC-DC converters operate synchronized to each other, with converter 1 as the master. A phase shift of 180°
between converter 1 and converter 2 decreases the input RMS current. Therefore smaller input capacitors can
be used. Converter 3 operates in phase with converter 1.
DCDC1 Converter
The output voltage for converter 1 is set to a fixed voltage internally in register DEFDCDC1. The voltage can be
changed using the I2C interface. The default settings are given in Table 1.
Optionally the voltage can be set by an external resistor divider if configured in register DEFDCDC1.
DCDC2 Converter
The VDCDC2 pin must be directly connected to the DCDC2 converter's output voltage. The DCDC2 converter's
output voltage can be selected via the DEFDCDC2 pin or optionally by changing the values in registers
DEFDCDC2_LOW and DEFDCDC2_HIGH. If pin DEFDCDC2 is pulled to GND, register DEFDCDC2_LOW
defines the output voltage. If the pin DEFDCDC2 is driven HIGH, register DEFDCDC2_HIGH defines the output
voltage. Therefore, the voltage can either be changed between two values by toggling pin DEFDCDC2 or by
changing the register values. Default voltages for DCDC1, DCDC2 and DCDC3 are:
Table 1. Default Voltages
DCDC1
DCDC2
DEFDCDC2=LOW
DCDC3
DEFDCDC2=HIGH
DEFDCDC3=LOW
DEFDCDC3=HIGH
DCDC3 Converter
The VDCDC3 pin must be directly connected to the DCDC3 converter's output voltage. The DCDC3 converter's
output voltage can be selected via the DEFDCDC3 pin or optionally by changing the values in registers
DEFDCDC3_LOW and DEFDCDC3_HIGH. If pin DEFDCDC3 is pulled to GND, register DEFDCDC3_LOW
defines the output voltage. If the pin DEFDCDC3 is driven HIGH, register DEFDCDC3_HIGH defines the output
voltage. Therefore, the voltage can either be changed between two values by toggling pin DEFDCDC3 or by
changing the register values.
LDO2 can optionally be forced to follow the voltage defined for DCDC3 by setting Bit LDO2 TRACKING in
register DEFLDO2.
POWER SAVE MODE
The Power Save Mode is enabled by default. If the load current decreases, the converter will enter Power Save
Mode operation automatically. During Power Save Mode the converter skips switching and operates with
reduced frequency in PFM mode and with a minimum quiescent current to maintain high efficiency. The
converter will position the output voltage typically +1% above the nominal output voltage. This voltage positioning
feature minimizes voltage drops caused by a sudden load step.
The transition from PWM Mode to PFM Mode occurs once the inductor current in the Low Side MOSFET switch
becomes 0.
30
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
During the Power Save Mode the output voltage is monitored with a PFM comparator. As the output voltage falls
below the PFM comparator threshold of VOUTnominal +1%, the device starts a PFM pulse. For this the High Side
MOSFET switch will turn on and the inductor current ramps up. Then it will be turned off and the Low Side
MOSFET switch will be turned on until the inductor current becomes 0.
The converter effectively delivers a current to the output capacitor and the load. If the load is below the delivered
current the output voltage will rise. If the output voltage is equal or higher than the PFM comparator threshold,
the device stops switching and enters a sleep mode with typical 15mA current consumption.
In case the output voltage is still below the PFM comparator threshold, further PFM current pulses will be
generated until the PFM comparator threshold is reached. The converter starts switching again once the output
voltage drops below the PFM comparator threshold.
With a single threshold comparator, the output voltage ripple during PFM Mode operation can be kept very small.
The ripple voltage depends on the PFM comparator delay, the size of the output capacitor and the inductor
value. Increasing output capacitor values and/or inductor values will minimize the output ripple.
The PFM Mode is left and PWM Mode entered in case the output current can not longer be supported in PFM
Mode or if the output voltage falls below a second threshold, called PFM comparator low threshold. This PFM
comparator low threshold is set to –1% below nominal Vout, and enables a fast transition from Power Save
Mode to PWM Mode during a load step. In Power Save Mode the quiescent current is reduced typically to 15mA.
The Power Save Mode can be disabled through the I2C interface for each of the step-down converters
independent from each other. If Power Save Mode is disabled, the converter will then operate in fixed PWM
mode.
Dynamic Voltage Positioning
This feature reduces the voltage under/overshoots at load steps from light to heavy load and vice versa. It is
active in Power Save Mode. It provides more headroom for both the voltage drop at a load step, and the voltage
increase at a load throw-off. This improves load transient behavior. At light loads, in which the converter operates
in PFM Mode, the output voltage is regulated typically 1% higher than the nominal value. In case of a load
transient from light load to heavy load, the output voltage drops until it reaches the PFM comparator low
threshold set to –1% below the nominal value and enters PWM mode. During a load throw off from heavy load to
light load, the voltage overshoot is also minimized due to active regulation turning on the Low Side MOSFET
switch.
Figure 30. Power Save Mode
100% Duty Cycle Low Dropout Operation
The device starts to enter 100% duty cycle Mode once the input voltage comes close the nominal output voltage.
In order to maintain the output voltage, the High Side MOSFET switch is turned on 100% for one or more cycles.
With further decreasing VIN the High Side MOSFET switch is turned on completely. In this case the converter
offers a low input-to-output voltage difference. This is particularly useful in battery-powered applications to
achieve longest operation time by taking full advantage of the whole battery voltage range.
The minimum input voltage to maintain regulation depends on the load current and output voltage, and can be
calculated as:
Vinmin = Voutmax + Ioutmax × (RDSonmax + RL)
(3)
(3)
With:
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
31
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
Ioutmax = maximum output current plus inductor ripple current
RDSonmax = maximum P-channel switch RDSon.
RL = DC resistance of the inductor
Voutmax = nominal output voltage plus maximum output voltage tolerance
Under-Voltage Lockout
The under voltage lockout circuit prevents the device from malfunctioning at low input voltages and from
excessive discharge of the battery and disables the DCDC converters and LDOs. The under-voltage lockout
threshold is configurable in the range of typically 2.8V to 3.25V with falling voltage at the SYS pin. The default
undervoltage lockout voltage as well as the hysteresis are defined in register CON_CTRL2. The default
undervoltage lockout voltage is 3.0V with 500mV hysteresis.
SHORT-CIRCUIT PROTECTION
The High Side and Low Side MOSFET switches are short-circuit protected with maximum output current = ILIMF.
Once the High Side MOSFET switch reaches its current limit, it is turned off and the Low Side MOSFET switch is
turned. The High Side MOSFET switch can only turn on again, once the current in the Low Side MOSFET switch
decreases below its current limit.
Soft Start
The 3 step-down converters in have an internal soft start circuit that controls the ramp up of the output voltage.
The output voltage ramps up from 5% to 95% of its nominal value within typ. 250ms. This limits the inrush current
in the converter during start up and prevents possible input voltage drops when a battery or high impedance
power source is used. The Soft start circuit is enabled after the start up time tStart has expired.
During soft start, the output voltage ramp up is controlled as shown in Figure 31.
EN
95%
5%
VOUT
tStart
tRAMP
Figure 31. Soft Start
ENABLE
To start up each converter independently, the device has a separate enable pin for each of the DCDC
converters. In order to enable any converter with its enable pins, the devices need to be in ON-state by pulling
PB_IN=LOW or POWER_ON=HIGH. The sequencing option programmed needs to be DCDC_SQ[2..0] = 101.
If EN_DCDC1, EN_DCDC2, EN_DCDC3 are set to high, the corresponding converter starts up with soft start as
previously described.
Pulling the enable pin low forces the device into shutdown, with a shutdown quiescent current as defined in the
electrical characteristics. In this mode, the high side and low side MOSFETs are turned-off, and the entire
internal control circuitry is switched-off. If disabled, the outputs of the DCDC converters are pulled low by internal
250Ω resistors, actively discharging the output capacitor. For proper operation the enable pins must be
terminated and must not be left floating.
32
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
Optionally, there is internal sequencing for the DCDC converters and both LDOs available. Bits DCDC_SQ[0..2]
in register CON_CTRL1 define the start-up and shut-down sequence for the DCDC converters. Depending on
the sequencing option, the signal at EN_DCDC1, EN_DCDC2 and EN_DCDC3 are ignored. For automatic
internal sequencing, the enable signals which are not used should be connected to GND.
LDO1 and LDO2 will start up automatically as defined in register LDO_CTRL1. See details about the sequencing
options in the register description for CON_CTRL1 and LDO_CTRL1.
RESET
The contain circuitry that can generate a reset pulse for a processor with a certain delay time. The input voltage
at a comparator is sensed at an input called THRESHOLD. When the voltage exceeds the threshold, the output
goes high with the delay time defined in register PGOOD. The reset circuitry is not active in OFF-state. The
pull-up resistor for this open drain output must not be connected directly to the battery as this may cause a
leakage path when the power path (SYS voltage) is turned off. The reset delay time equals the setting for the
PGOOD signal.
Vbat
THRESHOLD
/RESET
+
delay
-
Vref = 1 V
Vbat
THRESHOLD
comparator
output (internal)
RESET
T RESET
Figure 32. Reset Timing
PGOOD (reset signal for applications processor)
This open drain output generates a power-good signal depending on the status of the power good Bits for the
DCDC converters and the LDOs. Register PGOODMASK defines which of the power good Bits of the converters
and LDOs are used to drive the external PGOOD signal low when the voltage is below the target value. If e.g.,
Bit MASK DCDC2 is set to 1, the PGOOD pin will be driven low as long as the output of DCDC2 is below the
target voltage. If the output voltage of DCDC2 rises to its nominal value, the PGOOD pin will be released after
the delay time defined. See the default settings in the register description.
PB_IN (Push-button IN)
This pin is the ON/OFF button for the PMU to leave OFF-state and enter ON-state by pulling this pin to GND.
Entering ON-state will first ramp the output voltage of the power path (SYS), load the default register settings and
start up the DCDC converters and LDOs with the sequencing defined. In ON-state, the I2C interface is active and
the wLED converter can be enabled. The system turns on if PB_IN is pulled LOW for >50ms (debounce time)
AND the output voltage of the power path manager is above the undervoltage lockout voltage (AVDD6 > 3V).
This is for Vbat>3V OR VAC>3V OR VUSB>3V. The default voltage for the undervoltage lockout voltage can be
changed with Bits <UVLO1>, <UVLO0> in register CON_CTRL2. The value will be valid until the device was
turned off completely by entering Off state. The system turns off if PB_IN is released OR the system voltage falls
below the undervoltage lockout voltage of 3V. This is the case when either the battery voltage drops below 3.0V
or the input voltage at the pins AC or USB is below 3V. In order to keep the enabled after PB_IN is released
HIGH, there is an input pin called POWER_ON which needs to be pulled HIGH before the PB_IN button is
released. POWER_ON=HIGH will typically be asserted by the application processor to keep the PMU in
ON-state after the power button at PB_IN is released.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
33
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
In addition to this, there is a 15s timer which will drive PGOOD=LOW for 0.5ms when 15s are expired. The 15s
timer is enabled again when PB_IN is released HIGH. If PB_IN is pulled LOW for 30s continuously, PGOOD will
be driven LOW only once after the first 15s. When PGOOD is driven LOW due to PB_IN=low for 15s, all
registers in are set to their default value. See Figure 33.
Power OFF
SYS = OFF
voltage at AC applied OR
voltage at USB applied OR
PB_IN=0
Power OFF 2
SYS = ON
all voltages powered down
voltage at AC applied OR
voltage at USB applied
all voltages powered down
YES
NO
AC=1 OR
USB=1
WAIT FOR
POWER ON
SYS = ON
PB_IN=0
PB_IN=1 &&
POWER_ON=1
POWER
OFF 3
SYS = ON
PB_IN=0 (falling edge
detect)
POWER_ON=0
POWER
ON_1
SYS = ON
POWER_ON=1
DCDC converters
power down
LDOs power down
depending on
sequencing option
POWER
ON_2
SYS = ON
DCDC converters start
LDOs start
depending on sequencing option
Figure 33. State Machine
PB_OUT
This pin is a status output. PB_OUT is used as the wake-up interrupt to an application processor based on the
status of PB_IN. If PB_IN=LOW, PB_OUT = LOW (after 50ms debounce). If PB_IN=HIGH, PB_OUT= high
impedance (HIGH).
The pull-up resistor for this open drain output must not be connected directly to the battery as this may cause a
leakage path when the power path (SYS) is turned off.
POWER_ON
This pin is an input to the PMU which needs to be pulled HIGH for the PMU to stay in POWER ON_2-state once
PB_IN is released. Once this pin is pulled LOW while PB_IN=LOW, the PMU is shutting down without delay,
turning off the DCDC converters and the LDOs. If POWER_ON is pulled HIGH while there is power at USB or
AC, the will enter POWER ON_2-state and start the DCDC converters and LDOs according to the sequence
programmed. See Figure 33.
34
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
SHORT-CIRCUIT PROTECTION
All outputs are short circuit protected with a maximum output current as defined in the electrical specifications.
THERMAL SHUTDOWN
As soon as the junction temperature, TJ, exceeds typically 150°C for the DCDC converters or LDOs, the device
goes into thermal shutdown. In this mode, the high side MOSFETs are turned-off. The device continues its
operation when the junction temperature falls below the thermal shutdown hysteresis again. A thermal shutdown
for one of the DCDC converters or LDOs will disable all step-down converters simultaneously.
Low Dropout Voltage Regulators
The low dropout voltage regulators are designed to operate well with low value ceramic input and output
capacitors. They operate with input voltages down to 1.8V. The LDOs offer a maximum dropout voltage of
200mV at rated output current. Each LDO supports a current limit feature. LDO2 is enabled internally using Bit
ENABLE_LDO2 in register CON_CTRL1. The output voltage for LDO2 is defined by the settings in register
DEFLDO2. LDO2 can also be configured in such a way that it follows the output voltage of converter DCDC3 by
setting Bit LDO2 TRACKING = 1 in register DEFLDO2.
LDO1 is enabled internally using Bit ENABLE_LDO1 in register CON_CTRL1. The output voltage for LDO1 is
defined by the settings in register DEFLDO1. LDO1 can also be enabled automatically depending on the settings
in register LDO_CTRL1.
White LED Boost Converter
The converter is in shutdown mode by default and is being turned on by setting the enable Bit with the I2C
interface or for TPS65072 with pin EN_wLED. The enable Bit is located in register WLED_CTRL1 and is called
ENABLE ISINK as it enables the current sink for the white LEDs. Once enabled, an output voltage is
automatically generated at FB_wLED, high enough to force the programmed current through the string of white
LEDs. Two strings of white LEDs can be powered. The current in each of the two strings is regulated by an
internal current sink at pins Isink1 and Isink2. The maximum current through the current sinks is set with two
external resistors connected from pins ISET1 and ISET2 to GND. ISET1 sets the maximum current when Bit
CURRENT LEVEL in register WLED_CTRL2 is set to 1. If this Bit is set to 0, which is the default setting, the
maximum current is defined by the resistor connected at ISET2. This allows change between two different
maximum current settings during operation. The LED current can further be dimmed with an internal PWM signal.
The duty cycle for this PWM signal can be changed with the Bits LED DUTY CYCLE 0 to LED DUTY CYCLE 6 in
register WLED_CTRL2 in a range from 1% to 100%. In case a dimming ratio higher than 1:100 is needed, the
maximum LED current need to be changed to a lower value as defined with Iset2. In order to do this without any
flicker, the PWM dimming and the current level is defined in the same register, so both settings can be changed
at the same time with a single write access to register WLED_CTRL2. An internal overvoltage protection limits
the maximum voltage at FB_wLED to 37V typically. The output voltage at FB_WLED also has a lower limit which
is set to 12V. In case less than 4LEDs are used, the output voltage at the boost converter will not drop below
12V but the voltage from ISINK1 and ISINK2 to GND is increased accordingly.
A/D Converter
The 10Bit successive approximation (SAR) A/D converter with an input multiplexer can be used to monitor
different voltages in the system. These signals are monitored:
• Battery voltage
• Voltage at AC input
• Voltage at SYS output
• Input voltage of battery charger
• Battery temperature
• Battery charge current (voltage at pin Iset; Icharge = UISET/Rset × KISET)
• External voltage 1 to external voltage 4 (AD_IN1 to AD_IN4); 0V to 2.25V
• Optionally: External voltage 5 to external voltage 7 (AD_IN5 to AD_IN7); 0V to 6.0V
• Internal channel AD_IN14 and AD_IN15 for touch screen measurements
The A/D converter uses an internal 2.26V reference. The reference needs a bypass capacitor for stability which
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
35
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
is connected to pin BYPASS. The pin can be used as a reference output with a maximum output current of
0.1mA. The internal reference voltage is forced to be on when the ADC or the touch screen interface is enabled.
The reference voltage can additionally forced to be on using Bit Vref_enable in register ADCONFIG while ADC
and touch screen are off to allow external circuits to be supplied with a precise reference voltage while ADC and
touch screen are not used.
Touch Screen Interface
The touch screen itself consists of two parallel plates, called the X and Y plates, separated by short distance;
contact is initiated by using a stylus or your finger. This action creates a series of resistances noted by RX1,
RX2, RY1, RY2 , and Rcontact, shown in Figure 35. The points shown in the diagram as TSX1, TSX2, TSY1 and
TSY2 are connected to the touch screen interface. The resistances RX1 and RX2 scale linearly with the
x-position of the point of contact, where the RY1 and RY2 resistances scale with the y-position. The Rcontact
resistance decreases as the pressure applied at the point of contact increases and increases as the pressure
decreases. Using these relationships, the touch screen interface can make measurements of either position or
pressure.
X-Plate
TSX1
TSX2
RX1
RX2
Rcontact
TSY2
RY2
Y-Plate
RY1
TSY1
Figure 34. Touch Screen
The touch screen interface consists of a digital state machine, a voltage reference, and an analog switch matrix
which is connected to the four wire resistive touch screen inputs (TSX1, TSX2, TSY1, TSY2) and an internal
10-Bit ADC. The state machine controls the sequencing of the switch matrix to cycle through the three types of
measurement modes (position, pressure, plate resistance) and the low power standby mode. The separate
internal voltage reference (TSREF) is disabled in standby and off modes. The voltage is generated by an internal
LDO. Its voltage is bypassed by a capacitor connected to pin INT_LDO. The state of the touch screen is
controlled by the TSC_M[2,0] Bits of the TSCMODE register (08h) as shown in Table 2. The touch screen
controller uses transfer gates to the internal ADC on input channels AD_IN14 and AD_IN15.
Table 2. TSC Modes
CONTROL MULTIPLEXER
CONNECTIONS
MODE
MEASUREMENT
ADC_IN4
TGATE
X-Position
Voltage TSY1
TSREF
PMOS
GND
NMOS
Y-Position
Voltage TSX1
TSREF
GND
NMOS
GND
NMOS
Pressure
Current TSX1 and TSX2
TSREF
PMOS
GND
NMOS
HiZ
HiZ
Plate X
Reading on ADC_IN14
Current TSX1
0
HiZ
HiZ
TSREF
PMOS
GND
NMOS
Plate Y
Reading on ADC_IN14
Current TSY1
1
TSREF
TGATE
TSREF
TGATE
GND
NMOS
GND
NMOS
TSC standby
Voltage TSX1 and TSX2
TSC_M2
TSC_M1
TSC_M0
TSX1
TSX2
TSY1
TSY2
0
0
0
TSREF
PMOS
GND
NMOS
ADC_IN3
TGATE
0
0
1
ADC_IN1
TGATE
ADC_IN2
TGATE
0
1
0
TSREF
0
1
1
1
0
1
0
36
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
Table 2. TSC Modes (continued)
CONTROL MULTIPLEXER
CONNECTIONS
MODE
MEASUREMENT
A/D
TGATE
A/D
ADC used as stand alone
ADC using its analog inputs
OPEN
Disabled (no interrupt)
None
TSC_M2
TSC_M1
TSC_M0
TSX1
TSX2
TSY1
TSY2
1
1
0
A/D
TGATE
A/D
TGATE
A/D
TGATE
1
1
1
OPEN
OPEN
OPEN
If the Touch screen multiplexer is set to disabled mode [111], touch to the screen will not be detected. Standby
mode is entered by setting TSC_M[2:0] to 101. When there is a touch, the controller will detect a change in
voltage at the TSX1 point and after a 8ms deglitch the INT pin will be asserted if the interrupt is unmasked in
register INT. Once the host detects the interrupt signal, will enable the ADC converter and set the TSC_M<2:0>
via the I2C bus to select any of five measurements (position, pressure, plate) as shown in Table 3.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
37
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
Table 3. TSC Equations
MEASUREMENT
CHANNEL
EQUATION
X Plate resistance
AD_IN14
Rx = VTSREF/ [(VADC / 22k) × 150]
Y plate resistance
AD_IN14
Ry = VTSREF / [(VADC / 22k) × 150]
X position
AD_IN14
Xpos = Rx2 / (Rx1 + Rx2) = Rx2 / Rx
Rx2 = VADC x Rx/ VTSREF; Rx1 = Rx – Rx2
Xpos = ADRESULT / 1024
Y position
AD_IN14
Ypos = Ry2 / (Ry1 + Ry2) = Ry2 / Ry
Ry2 = VADC x Ry/ VTSREF; Ry1 = Ry – Ry2
Ypos = ADRESULT / 1024
Pressure
AD_IN14
Rc = R – Rx1//Rx2 – Ry1//Ry2
R = VTSREF/ [(VADC / 22k) × 150]
Rx1//Rx2 = Rx × Xpos × (1 – Xpos)
Ry1//Ry2 = Ry × Ypos × (1 – Ypos)
Performing Measurements Using the Touch Screen Controller
In order to take measurements with the touch screen controller, the ADC has to be enabled and configured for
use with the touch screen controller (TSC) first. In case the TSC is planned to be operated interrupt driven, the
TSC needs to be in TSC standby mode per default. Only in TSC standby mode an interrupt is generated based
on a touch of the screen. The TSC should therefore be in this mode until a touch is detected. Afterwards, the
TSC has to be configured for x-position measurement followed by y-position measurement. Now, the TSC can be
set to TSC standby again to wait for the next touch of the screen. For a non-interrupt driven sequence, see
TSCMODE. Register Address: 08h (page 50) in the Registers section. A typical interrupt driven sequence is
given below:
• Set TSCMODE to 101 to set TSC to TSC standby, so an interrupt is generated when the screen is touched
• Set Bit AD enable = 1 to provide power to the ADC
• Set input select for the ADC in register ADCONFIG to 1110 (AD_IN14 selected)
• In register INT, set MASK TSC = 1 to unmask the interrupt on a touch of the touch screen
• Read Bit TSC INT as it will be set after the TSC has been configured. Reading clears the interrupt.
• After a touch was detected, an interrupt is generated by INT pin going LOW
• Read Bit TSC INT to clear the interrupt
• Set TSCMODE to 000 to select x-position measurement
• Start an ADC conversion by setting CONVERSION START =1; wait until END OF CONVERSION = 1
• Read register ADRESULT_1 and AD_RESULT_2
• Set TSCMODE to 001 to select y-position measurement
• Start an ADC conversion by setting CONVERSION START =1; wait until END OF CONVERSION = 1
• Read register ADRESULT_1 and AD_RESULT_2
• Set TSCMODE to 101 to set TSC to TSC standby again
38
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
TO ADC
TSX1
TSY1
TO ADC
TSX1
TGATE
TGATE
TSY1
PMOS
PMOS
RX1
RY1
RY1
RX1
RC
TSREF
RC
RX2
TSREF
RY2
RY2
R X2
NMOS
TSX2
TSY2
NMOS
TSY2
TSX2
Y POSITION MEASUREMENT
X POSITION MEASUREMENT
Figure 35. Two Position Measurement
TSX1
I L/150
TSY1
IL
NMOS
R X1
RY1
TGATE
RC
TSREF
TO ADC
R X2
TGATE
RY2
22 kW
NMOS
TSY2
TSX2
PRESSURE MEASUREMET
Figure 36. Pressure Measurement
IL/150
IL
TSX1
TSY1
TSY1
PMOS
R X1
TGATE
TO ADC
TSX1
PMOS
R Y1
IL
TGATE
RC
RC
IL/150
R Y1
R X1
TSREF
TSREF
TGATE
RX2
R Y2
RX2
TO ADC
TGATE
R Y2
22 kW
22 kW
NMOS
NMOS
TSX2
TSY2
X PLATE RESISTANCE MEASUREMENT
TSX2
TSY2
Y PLATE RESISTANCE MEASUREMENT
Figure 37. Two Plate Resistance Measurement
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
39
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
TGATE
TSX1
TSY1
NMOS
TO INT BLOCK
TRESHOLD
DETECTOR
RX1
22 kW
R Y1
RC
TSREF
RX2
R Y2
NMOS
TGATE
TSX2
TSY2
STANDBY MODE
Figure 38. Touch Screen Standby Mode
I2C Interface Specification:
Serial interface
The serial interface is compatible with the standard and fast mode I2C specifications, allowing transfers at up to
400kHz. The interface adds flexibility to the power supply solution, enabling most functions to be programmed to
new values depending on the instantaneous application requirements and charger status to be monitored. The
has a 7-Bit address: ‘1001000’, other addresses are available upon contact with the factory. Attempting to read
data from register addresses not listed in this section will result in 00h being read out. For normal data transfer,
SDAT is allowed to change only when SCLK is low. Changes when SCLK is high are reserved for indicating the
start and stop conditions. During data transfer, the data line must remain stable whenever the clock line is high.
There is one clock pulse per Bit of data. Each data transfer is initiated with a start condition and terminated with
a stop condition. When addressed, the device generates an acknowledge Bit after the reception of each byte.
The master device (microprocessor) must generate an extra clock pulse that is associated with the acknowledge
Bit. The device must pull down the SDAT line during the acknowledge clock pulse so that the SDAT line is a
stable low during the high period of the acknowledge clock pulse. The SDAT line is a stable low during the high
period of the acknowledge–related clock pulse. Setup and hold times must be taken into account. During read
operations, a master must signal the end of data to the slave by not generating an acknowledge Bit on the last
byte that was clocked out of the slave. In this case, the slave device must leave the data line high to enable the
master to generate the stop condition.
All registers are set to their default value by one of these conditions:
• Voltage is below the UVLO threshold defined with registers <UVLO1>, <UVLO0>
• PB_IN is asserted LOW for >15s (option)
DATA
CLK
Data line
stable;
data valid
Change
of data
allowed
Figure 39. Bit Transfer on the Serial Interface
40
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
DATA
CLK
S
P
START Condition
STOP Condition
Figure 40. START and STOP Conditions
SCLK
...
SDAT
A6
...
A5 A4 ...
A0 R/W ACK
0
R7
R6
...
R5
R0 ACK
0
D7
D5 ...
D6
D0 ACK
0
Slave Address
Start
...
0
Register Address
Data
Stop
NOTE: SLAVE=TPS6507x
Figure 41. Serial I/f WRITE to TPS6507x
SCLK
...
SDAT
A6 ..
...
A0
R/W ACK
0
R7
..
...
R0
A6 ..
ACK
0
...
A0
0
R/W ACK
D7
Register
Address
D0
Slave
Drives
the Data
Slave Address
Repeated
Start
NOTE: SLAVE=TPS6507x
ACK
0
1
Start
Slave Address
..
Stop
Master
Drives
ACK and Stop
Figure 42. Serial I/f READ from TPS6507x: Protocol A
SCLK
...
SDAT
A6 ..
Start
...
A0
R/W ACK
0
R7 ..
..
0
Register
Address
Slave Address
A6 ..
R0 ACK
0
...
Stop Start
A0
R/W ACK
D7 ..
D0
ACK
0
1
Slave Address
Slave
Drives
the Data
Stop
Master
Drives
ACK and Stop
Figure 43. Serial I/f READ from TPS6507x: Protocol B
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
41
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
DATA
t( BUF)
th(STA)
t(LOW)
tr
tf
CLK
t h(STA)
t(HIGH)
th(DATA)
STO
STA
tsu(STA)
tsu(STO)
tsu(DATA)
STA
STO
Figure 44. Serial I/f Timing Diagram
MIN MAX
fMAX
Clock frequency
twH(HIGH)
Clock high time
600
twL(LOW)
Clock low time
1300
tR
SDAT and CLK rise time
tF
SDAT and CLK fall time
th(STA)
Hold time (repeated) START condition (after this period the first clock pulse is generated)
600
ns
th(SDAT)
Setup time for repeated START condition
600
ns
th(SDAT)
Data input hold time
0
ns
tsu(SDAT)
Data input setup time
100
ns
tsu(STO)
STOP condition setup time
600
ns
t(BUF)
Bus free time
1300
ns
42
Submit Documentation Feedback
400
UNIT
kHz
ns
ns
300
ns
300
ns
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
REGISTERS
PPATH1. Register Address: 01h
PPATH1
Bit name and
function
Default
Set by signal
B7
B6
USB power
AC power
x
x
B5
USB power
enable
0
B4
AC power
enable
0
UVLO
UVLO
R/W
R/W
Default value
loaded by:
Read/write
R
R
B3
AC input
current MSB
1
B2
AC input
current LSB
1
Voltage
Voltage
removed at
removed at
AC OR UVLO AC OR UVLO
R/W
R/W
B1
USB input
current MSB
0
BO
USB input
current LSB
1
Voltage
removed at
USB OR
UVLO
R/W
Voltage
removed at
USB OR
UVLO
R/W
Bit 7
USB power:
0 = USB power is not present and/or not in the range valid for charging
1 = USB source is present and in the range valid for charging. B7 remains active as long as the
charge source is present
Bit 6
AC power:
0 = wall plug is not present and/or not in the range valid for charging
1 = wall plug source is present and in the range valid for charging. B6 remains active as long as the
charge source is present
Bit 5
USB POWER ENABLE
0 = USB power input is enabled
1 = USB power input is disabled (USB suspend mode)
Bit 4
AC POWER ENABLE
0 = AC power input is enabled
1 = AC power input is disabled
Bit 3..2
AC INPUT CURRENT
00 = input current from AC
01 = input current from AC
10 = input current from AC
11 = input current from AC
Bit 1..0
input
input
input
input
USB INPUT CURRENT
00 = input current from USB
01 = input current from USB
10 = input current from USB
11 = input current from USB
is
is
is
is
input
input
input
input
100 mA max
500 mA max
1300 mA max
2500 mA
is 100 mA max
is 500 mA max
is 800 mA max
is 1300 mA max
Note: safety timers are cleared if the input voltage at both AC and USB are removed.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
43
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
INT. Register Address: 02h
INT
B7
B6
B5
Bit name and
function
MASK
AC/USB
MASK TSC
MASK
PB_IN
Default
0
0
0
UVLO
UVLO
UVLO
R/W
R/W
R/W
B4
0
Set by signal
Default value
loaded by:
Read/write
R
B3
B2
B1
BO
USB
or
AC
USB
or AC
PB_IN
TSC INT
input voltage input voltage
INT
applied
removed
0
0
0
0
Cleared when Cleared when Cleared when Cleared when
read
read
read
read
UVLO
UVLO
UVLO
UVLO
R
R
R
R
Bit 7
MASK AC/USB
0 = no interrupt generated if voltage at AC or USB is applied or removed
1 = the pin INT is actively pulled low if one of the Bits 1 to Bit 0 are 1
Bit 6
MASK TSC
0 = no interrupt generated if the touch screen is detecting a “touch”
1 = the pin INT is actively pulled low if a “touch” on the touch screen is detected
Bit 5
MASK PB_IN
0 = no interrupt generated if the PB_IN is pulled low.
1 = the pin INT is actively pulled low if PB_IN was pulled low.
Bit 3
TSC INT
0 = no “touch” on the touch screen detected
1 = “touch” detected and the Bit has not been read ever since
Bit 2
PB_IN INT
0 = PB_IN not active
1 = PB_IN is actively pulled low (or high optionally) and the Bit has not been read ever since
Bit 1
USB or AC INPUT VOLTAGE APPLIED
0 = no change (voltage still applied or never applied)
1 = voltage at USB or AC has been applied and the Bit has not been read ever since
Bit 0
USB or AC INPUT VOLTAGE REMOVED
0 = no change (voltage still applied or never applied)
1 = the voltage at USB or AC has been removed and the Bit has not been read ever since
44
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
CHGCONFIG0. Register Address: 03h
CHGCONFIG0
Bit name and function
Default
Set by signal
Default value loaded by:
Read/write
B7
Thermal
regulation
x
B6
DPPM
active
x
B5
Thermal
Suspend
x
B4
Term
Current
x
UVLO
R
UVLO
R
UVLO
R
UVLO
R
B3
0
B2
Chg
Timeout
x
B1
Prechg
Timeout
x
BO
BatTemp
error
x
R
UVLO
R
UVLO
R
UVLO
R
Bit 7
THERMAL REGULATION:
0 = charger is in normal operation
1 = charge current is reduced due to high chip temperature
Bit 6
DPPM ACTIVE:
0 = DPPM loop is not active
1 = DPPM loop is active; charge current is reduced to support the load with the current required
Bit 5
THERMAL SUSPEND:
0 = charging is allowed
1 = charging is momentarily suspended because battery temperature is out of range
Bit 4
TERM CURRENT:
0 = charge termination current threshold has not been crossed; charging or no voltage at AC and
USB
1 = charge termination current threshold has been crossed and charging has been stopped. This
can be due to a battery reaching full capacity or to a battery removal condition
Bit 2..Bit1
CHG TIMEOUT, PRECHG TIMEOUT
0 = charging, timers did not time out
1 = one of the timers has timed out and charging has been terminated
Bit 0
BAT TEMP ERROR:
0 = battery temperature is in the allowed range for charging
1 = no temperature sensor detected
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
45
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
CHGCONFIG1. Register Address: 04h
CHGCONFIG1
B7
B6
B5
B4
B3
Bit name and function
Charge safety
timer value1
Charge safety
timer value0
Safety timer
enable
SENSOR
TYPE
Charger
reset
0
0
1
1
UVLO
UVLO
UVLO
R/W
R/W
R/W
Default
Set by signal
Default value loaded
by:
Read/write
B1
BO
Suspend
Charge
Charger
enable
0
B2
Charge
Termination
ON/OFF
0
0
1
UVLO
UVLO
UVLO
UVLO
UVLO
R/W
R/W
R/W
R/W
R/W
Bit 7..6 CHARGE SAFETY TIMER VALUE0/1:
00 = safety timer times out after 4 hours
01 = safety timer times out after 5 hours
10 = safety timer times out after 6 hours
11 = safety timer times out after 8 hours
Bit 5
SAFETY TIMER ENABLE
0 = pre-charge timer, fast charge timer and taper timers are disabled
1 = pre-charge timer, fast charge timer and taper timers are enabled
Bit 4
SENSOR TYPE (NTC for battery temperature measurement)
0 = 100k curve 1 NTC
1 = 10k curve 2 NTC
Bit 3
CHARGER RESET:
0 = inactive
1 = Reset active. This Bit must be set and then reset via the serial interface to restart the charge
algorithm
Bit 2
CHARGE TERMINATION ON/OFF:
0 = charge termination enabled, based on timers and termination current
1 = charge termination will not occur and the charger will always be on
Bit 1
SUSPEND CHARGE:
0 = Safety Timer and Pre-Charge timers are not suspended
1 = Safety Timer and Pre-Charge timers are suspended
Bit 0
CHARGER ENABLE
0 = charger is disabled
1 = charger is enabled; toggling the enable Bit will not reset the charger. Use CHARGER RESET Bit to
reset charger.
46
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
CHGCONFIG2. Register Address: 05h
CHGCONFIG2
Bit name and function
Default
Set by signal
Default value loaded by:
Read/write
B7
Dynamic
Timer
function
1
B6
1
B5
Charge
voltage
selection1
1
B4
Charge
voltage
selection0
0
Precharge
voltage
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
B3
B2
B1
BO
0
0
0
0
R
R
R
R
Bit 7
DYNAMIC TIMER FUNCTION
0 = safety timers run with their nominal clock speed
1 = clock speed is divided by 2 if thermal loop or DPPM loop is active
Bit 6
PRECHARGE VOLTAGE
0 = pre-charge to fast charge transition voltage is 2.5V
1 = pre-charge to fast charge transition voltage is 2.9V
Bit 5..4
CHARGE VOLTAGE SELECTION0/1:
00 = 4.10V
01 = 4.15V
10 = 4.20V
11 = 4.25V
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
47
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
CHGCONFIG3. Register Address: 06h
CHGCONFIG3
B7
Bit name and function
Disable
Isink at AC
Default
Set by signal
Default value loaded by:
Read/write
B5
Power path
DPPM
threshold0
1
Precharge
time
0
B6
Power path
DPPM
threshold1
1
B4
B2
Termination
current
factor0
1
B1
BO
Charger
active
Disable
Isink at USB
0
B3
Termination
current
factor1
0
x
0
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R
UVLO
R/W
Bit 7
DISABLE ISINK AT AC (disables an internal current sink from pin AC to GND)
0 = 60 mA current sink enabled when no input voltage at pin AC detected
1 = 60 mA current sink disabled
Bit 6..5
POWER PATH DPPM THRESHOLD1/0:
00 = 3.5 V
01 = 3.75 V
10 = 4.25 V
11 = 4.50 V
Bit 4
PRECHARGE TIME
0 = pre-charge time is 30 min
1 = pre-charge time is 60 min
Bit 3..2
TERMINATION CURRENT FACTOR1/0:
00 = 0.04
01 = 0.1
10 = 0.15
11 = 0.2
Bit 1
CHARGER ACTIVE:
0 = charger is not charging
1 = charger is charging (DPPM or thermal regulation may be active)
Bit 0
DISABLE ISINK AT USB (disables an internal current sink from pin USB to GND)
0 = 60 mA current sink enabled when no input voltage at pin USB detected
1 = 60 mA current sink disabled
Note: There is a current sink on pins AC and USB which is activated when there is no voltage detected at
the pin and Bit7 or Bit0 in CHCONFIG3 are set to 0. This is implemented in order to avoid the pins to
be floating when not connected to a power source. The current sink is disabled automatically as soon
as an input voltage is detected at the pin.
48
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
ADCONFIG. Register Address: 07h
ADCONFIG
B7
B5
End of
conversion
1
Vref enable
0
B6
Conversion
start
0
Bit name and function
AD enable
Default
Set by signal
Default value loaded by:
Read/write
B4
0
B3
INPUT
SELECT_3
0
B2
INPUT
SELECT_2
0
B1
INPUT
SELECT_1
0
BO
INPUT
SELECT_0
0
UVLO
R/W
UVLO
R/W
UVLO
R
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
Bit 7
AD ENABLE:
0 = A/D converter disabled
1 = A/D converter enabled
Bit 6
CONVERSION START
0 = no conversion in progress
1 = start A/D conversion, Bit is automatically cleared if conversion is done
Bit 5
END OF CONVERSION
0 = conversion did not finish
1 = conversion done
Bit 4
VREF ENABLE
0 = reference voltage LDO (pin BYPASS) for ADC is disabled
1 = reference voltage LDO (pin BYPASS) for ADC is enabled
Bit 3..0
INPUT SELECT – see table
INPUT
SELECT_3
INPUT
SELECT_2
INPUT
SELECT_1
INPUT
SELECT_0
FULL SCALE
INPUT VOLTAGE
INPUT SELECTED
0
0
0
0
2.25V
Voltage at AD_IN1
0
0
0
1
2.25V
Voltage at AD_IN2
0
0
1
0
2.25V
Voltage at AD_IN3
0
0
1
1
2.25V
Voltage at AD_IN4
0
1
0
0
2.25V
Voltage at TS pin
0
1
0
1
2.25V
Voltage at ISET pin == battery charge
current
0
1
1
0
6.0V
Voltage at AC pin
0
1
1
1
6.0V
Voltage at SYS pin
1
0
0
0
6.0V
Input voltage of the charger
1
0
0
1
6.0V
Voltage at BAT pins
1
0
1
0
6.0V
Voltage at AD_IN5 (at pin
THRESHOLD)
1
0
1
1
6.0V
Voltage at AD_IN6 (at pin ISET1)
1
1
0
0
6.0V
Voltage at AD_IN7 (at pin ISET2)
1
1
1
0
2.25
Touch screen controller (TSC);
all functions
1
1
1
1
2.25
Touch screen controller (TSC);
x-position and y-position only
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
49
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
TSCMODE. Register Address: 08h
TSCMODE
Bit name and function
Default
Set by signal
Default value loaded by:
Read/write
B7
B6
B5
B4
B3
0
B2
TSC_M2
1
B1
TSC_M1
1
BO
TSC_M0
1
0
0
0
0
R
R
R
R
R
UVLO
R/W
UVLO
R/W
UVLO
R/W
Bit 3..0 MODE SELECT BITS FOR THE TOUCH SCREEN INTERFACE
Note: Data conversions using the touch screen interface require setting the touch screen mode with register
TSCMODE and selecting the analog input channel for the ADC according to the following table.
Measurement of x-position:
• Set TSCMODE to 000 to select x-position measurement
• Set Bit AD ENABLE=1 to provide power to the ADC.
• Set input select for the ADC in register ADCONFIG to 1110 (AD_IN14 selected).
• Start a conversion by setting CONVERSION START=1; wait until END OF CONVERSION=1
• Read register ADRESULT_1 and ADRESULT_2
TSC_M2
TSC_M1
TSC_M0
TSX1
(AD_IN1)
TSX2
(AD_IN2)
TSY1(AD_ TSY2(AD_
IN3)
IN4)
MODE
MEASUREMENT
0
0
0
TSREF
GND
A/D
0
0
1
A/D
HiZ
TSREF
HiZ
X-Position
Voltage TSY1
GND
Y-Position
0
1
0
TSREF
TSREF
GND
Voltage TSX1
GND
Pressure
Current TSX1 and
TSX2
0
1
1
TSREF
GND
1
0
0
HiZ
HiZ
HiZ
HiZ
Plate X
Current TSX1
TSREF
GND
Plate Y
Current TSY1
1
0
1
V2
V2
GND
GND
TSC standby
Voltage TSX1 and
TSX2
1
1
0
A/D
A/D
A/D
A/D
A/D
Voltage measurement
with ADC
1
1
1
open
open
open
open
TSC and ADC
disabled (no interrupt
generation)
ADRESULT_1. Register Address: 09h
ADRESULT_1
Bit name and function
Default
Set by signal
Default value loaded
by:
Read/write
50
B7
AD_BIT7
x
B6
AD_BIT6
x
B5
AD_BIT5
x
B4
AD_BIT4
x
B3
AD_BIT3
x
B2
AD_BIT2
x
B1
AD_BIT1
x
BO
AD_BIT0 LSB
x
R
R
R
R
R
R
R
R
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
ADRESULT_2. Register Address: 0Ah
ADRESULT_2
B7
B6
B5
B4
B3
B2
0
0
0
0
0
0
B1
AD_BIT9
MSB
x
R
R
R
R
R
R
R
R
B6
PGOOD
DELAY 1
B5
PGOOD
DELAY 0
B4
PGOOD
VDCDC1
B3
PGOOD
VDCDC2
B2
PGOOD
VDCDC3
B1
PGOOD
LDO1
BO
PGOOD
LDO2
x
1
1
x
0
0
PGOOD
VDCDC1
PGOOD
VDCDC1
R
PGOOD
VDCDC2
PGOOD
VDCDC2
R
PGOOD
VDCDC3
PGOOD
VDCDC3
R
PGOOD
LDO1
PGOOD
LDO1
R
PGOOD
LDO2
PGOOD
LDO2
R
Bit name and function
Default
Set by signal
Default value loaded by:
Read/write
BO
AD_BIT8
x
PGOOD. Register Address: 0Bh
PGOOD
B7
Bit name and function
Reset
Default for
–70, -73, -731, -732
Default for TPS65072
Set by signal
Default value loaded by:
Read/write
Bit 7
R
R/W
R/W
Reset:
0 = indicates that the comparator input voltage is above the 1V threshold.
1 = indicates that the comparator input voltage is below the 1V threshold.
Bit 6..5 PGOOD DELAY 0,1 (sets the delay time of Reset and PGOOD output):
00 = delay is 20ms
01 = delay is 100ms
10 = delay is 200ms
11 = delay is 400ms
Bit 4
PGOOD VDCDC1:
0 = indicates that the VDCDC1 converter output voltage is below its target regulation voltage or
disabled.
1 = indicates that the VDCDC1 converter output voltage is within its nominal range.
Bit 3
PGOOD VDCDC2:
0 = indicates that the VDCDC2 converter output voltage is below its target regulation voltage or
disabled.
1 = indicates that the VDCDC2 converter output voltage is within its nominal range.
Bit 2
PGOOD VDCDC3:
0 = indicates that the VDCDC3 converter output voltage is below its target regulation voltage or
disabled 1 = indicates that the VDCDC3 converter output voltage is within its nominal range.
Bit 1
PGOOD LDO1:
0 = indicates that LDO1 output voltage is below its target regulation voltage or disabled
1 = indicates that the LDO1 output voltage is within its nominal range.
Bit 0
PGOOD LDO2:
0 = indicates that the LDO2 output voltage is below its target regulation voltage or disabled.
1 = indicates that the LDO2 output voltage is within its nominal range.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
51
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
PGOODMASK. Register Address: 0Ch
B7
B6
0
0
0
0
B5
MASK
VDCDC3 and
LDO1
0
0
0
0
0
1
1
1
0
0
UVLO
UVLO
UVLO
UVLO
UVLO
UVLO
R/W
R/W
R/W
R/W
R/W
R/W
Bit name and function
Default for –70
Default for -72
Default for -73, -731,
-732
Set by signal
Default value loaded
by:
Read/write
R
R
B4
B3
B2
B1
BO
MASK
VDCDC1
MASK
VDCDC2
MASK
VDCDC3
MASKLDO1
MASK
LDO2
0
1
1
0
0
0
0
0
0
0
Bit 5
MASK VDCDC3 and LDO1:
0 = indicates that the output voltage of either DCDC3 or LDO1 is within its nominal range. The
PGOOD output is not affected (not driven LOW)
1 = indicates that both LDO1 AND DCDC3 output voltage is below its target regulation voltage or
disabled. This will drive the PGOOD output low.
Bit 4..0
MASK VDCDC1/2/3, LDO1,2:
0 = the status of the power good Bit in Register PGOOD does not affect the status of the PGOOD
output pin
1 = the PGOOD pin is driven low in case the output voltage of the converter or LDO is below its
target regulation voltage or disabled.
52
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
CON_CTRL1. Register Address: 0Dh
CON_CTRL1
B7
B6
B5
Bit name and function
DCDC_SQ2
DCDC_SQ1
DCDC_SQ0
Default for
–70, –72, -73, -732
for TPS65731 only
See Table 9
See Table 9
See Table 9
Set by signal
Default value loaded by:
Read/write
UVLO
R/W
UVLO
R/W
UVLO
R/W
B4
DCDC1
ENABLE
B3
DCDC2
ENABLE
B2
DCDC3
ENABLE
B1
LDO1
ENABLE
BO
LDO2
ENABLE
1
1
1
1
1
1
1
1
1
0
DCDC1_E DCDC2_EN DCDC3_EN
LDO_ENZ
NZ
Z
Z
UVLO
UVLO
UVLO
UVLO
R/W
R/W
R/W
R/W
LDO_ENZ
UVLO
R/W
The CON_CTRL1 register can be used to disable and enable all power supplies via the serial interface. Default
is to allow all supplies to be on, providing the relevant enable pin is high. The following tables indicate how the
enable pins and the CON_CTRL1 register are combined. The CON_CTRL1 Bits are automatically reset to
default when the corresponding enable pin is low.
Bit 7..5
DCDC_SQ2 to DCDC_SQ0: power-up sequencing (power down sequencing is the reverse)
000 = power-up sequencing is: DCDC2 only; DCDC1 and DCDC3 are not part of the automatic
sequencing and are enabled by their enable pins EN_DCDC1 and EN_DCDC3
001 = power-up sequencing is DCDC2 and DCDC3 at the same time, DCDC1 is not part of the
automatic sequencing and is enabled by its enable pin EN_DCDC1
010 = power-up sequencing is: DCDC1 when power good then DCDC2 and DCDC3 at the same time
011 = power-up sequencing is: DCDC3 when power good then DCDC2; DCDC1 is not part of the
automatic sequencing and is controlled by its EN_DCDC1 pin.
100 = power-up sequencing is: DCDC3 is started at the same time with LDO2 if Bit
MASK_EN_DCDC3 in register 0Eh is set (default is set). DCDC1 and DCDC2 are started at the same
time when LDO2 is PGOOD (defined in LDO sequencing 111); DCDC3 is enabled or disabled with its
EN_DCDC3 pin if MASK_EN_DCDC3 in register 0Eh is cleared (set =0). (Sirf PRIMA, start-up from
OFF or start-up after SLEEP)
101 = DCDC converters are enabled individually with the external enable pins
110 = DCDC1first, when power good then DCDC2, when power good then DCDC3
111 = power-up sequencing is: DCDC1 and DCDC2 at the same time >1ms after LDO2 has been
started (defined in LDO sequencing 010); DCDC3 is not part of the automatic sequencing but is
enabled with its EN_DCDC3 pin (Atlas4)
In case of automatic sequencing other than 101, the start is initiated by going into ON-state. DCDC converters
that are not part of the automatic sequencing can be enabled by pulling their enable pin to a logic HIGH level at
any time in ON-state. The enable pins for the converters that are automatically enabled, should be tied to GND.
For sequencing option DCDC_SEQ=111, the start is initiated by going into ON-state, however, the external LDO
connected to pin EN_EXTLDO is powered first, followed by LDO2.
(The sequencing of LDO1 and LDO2 is defined in register LDO_CTRL1)
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
53
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
Bit 4..0
EN_DCDC1 PIN
www.ti.com
DCDC1,2,3: See tables below
CON_CTRL1<4>
DCDC1 CONVERTER
EN_DCDC2 PIN
0
x
disabled
1
0
disabled
1
1
enabled
EN_DCDC3 PIN
54
Submit Documentation Feedback
CON_CTRL1<3>
DCDC2
CONVERTER
0
x
disabled
1
0
disabled
1
1
enabled
CON_CTRL1<2>
DCDC3 CONVERTER
0
x
disabled
1
0
disabled
1
1
enabled
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
CON_CTRL2. Register Address: 0Eh
CON_CTRL2
Bit name and function
Default value loaded
by:
Read/write
B7
ENABLE
1s timer
B6
ENABLE
5s timer
B5
B4
B3
DS_RDY
PWR_D
S
MASK_EN_DCDC3
UVLO
UVLO
UVLO
UVLO
UVLO
R/W
R/W
R/W
R/W
R/W
B2
UVLO
hysteresis
B1
BO
UVLO1
UVLO0
BG_GOOD
BG_GOOD
BG_GOOD
R/W
R/W
R/W
Bit 7…6
ENABLE TIMERS:
0 = the state machine timers of 1s and 5s, respectively are disabled
1 = the state machine timers of 1s and 5s, respectively are enabled
Bit 5
DS_RDY (data ready, memory content valid) for use with Sirf Prima processor DEEP SLEEP
mode:
0 = status Bit which is indicating the memory content is not valid after wake up from DEEP SLEEP.
This Bit is set / cleared by the Prima application processor. Cleared when device is in UVLO to tell
processor there was a power loss. The Bits needs to be cleared by user software after a wake up
from DEEP SLEEP to enable the DCDC2 converter to be powered down in shutdown sequencing
depending on the status of LDO2.
1 = memory content is valid after wake up from DEEP SLEEP (set by I2C command by application
processor only). The Prima processor is ready to power down to DEEP SLEEP mode or was just
waking up from DEEP SLEEP mode.
Bit 4
PWR_DS (enter DEEP SLEEP for sequencing option DCDC_SEQ=100, LDO_SQ=111):
0 = PMU is in normal operation
1 = PMU powers down all rails except DCDC2 and the external LDO on pin “EXT_LDO”. PGOOD
is pulled LOW.
Bit 3
MASK_EN_DCDC3; used for Prima application processor start-up sequencing:
0 = DCDC3 is enabled or disabled by the status of EN_DCDC3 for sequencing option
DCDC_SEQ=100.
1 = DCDC3 will start at the same time with LDO2 for sequencing option DCDC_SEQ=100. The
status of EN_DCDC3 is ignored
Bit 2
UNDERVOLTAGE LOCKOUT HYSTERESIS:
0 = 400mV hysteresis
1 = 500mV hysteresis
Bit 1..0
UVLO1, UVLO2 (undervoltage lockout voltage):
00 = the device turns off at 2.8V with the reverse of the sequencing defined in CON_CTRL1
01 = the device turns off at 3.0V with the reverse of the sequencing defined in CON_CTRL1
10 = the device turns off at 3.1V with the reverse of the sequencing defined in CON_CTRL1
11 = the device turns off at 3.25V with the reverse of the sequencing defined in CON_CTRL1
Note: The undervoltage lockout voltage is sensed at the SYS pin and the device goes to OFF state when
the voltage is below the value defined in the register. BG_GOOD is the internal bandgap good
signal which occurs at lower voltages than UVLO.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
55
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
CON_CTRL3. Register Address: 0Fh
CON_CTRL3
Bit name and function
Default value loaded by:
Read/write
B7
FPWM
DCDC3
UVLO
R/W
B6
FPWM
DCDC2
UVLO
R/W
B5
FPWM
DCDC1
UVLO
R/W
B4
DCDC1
discharge
UVLO
R/W
B3
DCDC2
discharge
UVLO
R/W
B2
DCDC3
discharge
UVLO
R/W
B1
LDO1
discharge
UVLO
R/W
BO
LDO2
discharge
UVLO
R/W
Bit 7
FPWM DCDC3:
0 = DCDC3 converter operates in PWM / PFM mode
1 = DCDC3 converter is forced into fixed frequency PWM mode
Bit 6
FPWM DCDC2:
0 = DCDC2 converter operates in PWM / PFM mode
1 = DCDC2 converter is forced into fixed frequency PWM mode
Bit 5
FPWM DCDC1:
0 = DCDC1 converter operates in PWM / PFM mode
1 = DCDC1 converter is forced into fixed frequency PWM mode
Bit 4–0
0 = the output capacitor of the associated converter or LDO is not actively discharged when
the converter or LDO is disabled
1 = the output capacitor of the associated converter or LDO is actively discharged when the
converter or LDO is disabled. This decreases the fall time of the output voltage at light load
DEFDCDC1. Register Address: 10h
DEFDCDC1
Bit name and function
Default value loaded by:
Read/write
B7
DCDC1
extadj
UVLO
R/W
B6
UVLO
R
B5
B4
B3
B2
B1
BO
DCDC1[5]
DCDC1[4]
DCDC1[3]
DCDC1[2]
DCDC1[1]
DCDC1[0]
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
DEFDCDC1 sets the output voltage for the DCDC1 converter. Per default the converter is internally fixed but can
be programmed to an externally adjustable version by setting Bit 7 (Ext adj). The default setting is defined in an
EEPROM Bit. In case the externally adjustable version is programmed, the external resistor divider need to be
connected to the VDCDC1 pin, otherwise this pin needs to be connected to the output voltage directly. For the
fixed voltage version, the output voltage is set with Bits B0 to B5 (DCDC1[5] to DCDC1[0]):
All step-down converters provide the same output voltage range, see details under DEFDCDC3
56
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
DEFDCDC2_LOW. Register Address: 11h
DEFDCDC2_LOW
Bit name and function
Default value loaded by:
Read/write
B7
B6
R
R
B5
DCDC2[5]
UVLO
R/W
B4
DCDC2[4]
UVLO
R/W
B3
DCDC2[3]
UVLO
R/W
B2
DCDC2[2]
UVLO
R/W
B1
DCDC2[1]
UVLO
R/W
BO
DCDC2[0]
UVLO
R/W
B5
DCDC2[5]
B4
DCDC2[4]
B3
DCDC2[3]
B2
DCDC2[2]
B1
DCDC2[1]
BO
DCDC2[0]
UVLO
UVLO
UVLO
UVLO
UVLO
UVLO
R/W
R/W
R/W
R/W
R/W
R/W
DEFDCDC2_HIGH. Register Address: 12h
DEFDCDC2_HIGH
Bit name and function
Default value loaded
by:
Read/write
B7
DCDC2 extadj
B6
UVLO
R/W
R
The output voltage for DCDC2 is switched between the value defined in DEFDCDC2_LOW and
DEFDCDC2_HIGH depending on the status of the DEFDCDC2 pin. IF DEFDCDC2 is LOW the value in
DEFDCDC2_LOW is selected, if DEFDCDC2 = HIGH, the value in DEFDCDC2_HIGH is selected. Per default
the converter is internally fixed but can be programmed to an externally adjustable version by EEPROM similar to
DCDC1.
DEFDCDC3_LOW. Register Address: 13h
DEFDCDC3_LOW
Bit name and function
Default value loaded by:
Read/write
B7
B6
R/W
R
B5
DCDC3[5]
UVLO
R/W
B4
DCDC3[4]
UVLO
R/W
B3
DCDC3[3]
UVLO
R/W
B2
DCDC3[2]
UVLO
R/W
B1
DCDC3[1]
UVLO
R/W
BO
DCDC3[0]
UVLO
R/W
B5
B4
B3
B2
B1
BO
DCDC3[5]
DCDC3[4]
DCDC3[3]
DCDC3[2]
DCDC3[1]
DCDC3[0]
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
UVLO
R/W
DEFDCDC3_HIGH. Register Address: 14h
DEFDCDC3_HIGH
Bit name and function
Default value loaded by:
Read/write
B7
DCDC3
extadj
UVLO
R/W
B6
R
The output voltage for DCDC3 is switched between the value defined in DEFDCDC3_LOW and
DEFDCDC3_HIGH depending on the status of the DEFDCDC3 pin. IF DEFDCDC3 is LOW the value in
DEFDCDC3_LOW is selected, if DEFDCDC3 = HIGH, the value in DEFDCDC3_HIGH is selected. Per default
the converter is internally fixed but can be programmed to an externally adjustable version by EEPROM similar to
DCDC2.
OUTPUT VOLTAGE
[V]
B5
B4
B3
B2
B1
B0
0.725
0
0
0
0
0
0
0.750
0
0
0
0
0
1
0.775
0
0
0
0
1
0
0.800
0
0
0
0
1
1
0.825
0
0
0
1
0
0
0.850
0
0
0
1
0
1
0.875
0
0
0
1
1
0
0.900
0
0
0
1
1
1
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
57
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
58
www.ti.com
OUTPUT VOLTAGE
[V]
B5
B4
B3
B2
B1
B0
0.925
0
0
1
0
0
0
0.950
0
0
1
0
0
1
0.975
0
0
1
0
1
0
1.000
0
0
1
0
1
1
1.025
0
0
1
1
0
0
1.050
0
0
1
1
0
1
1.075
0
0
1
1
1
0
1.100
0
0
1
1
1
1
1.125
0
1
0
0
0
0
1.150
0
1
0
0
0
1
1.175
0
1
0
0
1
0
1.200
0
1
0
0
1
1
1.225
0
1
0
1
0
0
1.250
0
1
0
1
0
1
1.275
0
1
0
1
1
0
1.300
0
1
0
1
1
1
1.325
0
1
1
0
0
0
1.350
0
1
1
0
0
1
1.375
0
1
1
0
1
0
1.400
0
1
1
0
1
1
1.425
0
1
1
1
0
0
1.450
0
1
1
1
0
1
1.475
0
1
1
1
1
0
1.500
0
1
1
1
1
1
1.550
1
0
0
0
0
0
1.600
1
0
0
0
0
1
1.650
1
0
0
0
1
0
1.700
1
0
0
0
1
1
1.750
1
0
0
1
0
0
1.800
1
0
0
1
0
1
1.850
1
0
0
1
1
0
1.900
1
0
0
1
1
1
1.950
1
0
1
0
0
0
2.000
1
0
1
0
0
1
2.050
1
0
1
0
1
0
2.100
1
0
1
0
1
1
2.150
1
0
1
1
0
0
2.200
1
0
1
1
0
1
2.250
1
0
1
1
1
0
2.300
1
0
1
1
1
1
2.350
1
1
0
0
0
0
2.400
1
1
0
0
0
1
2.450
1
1
0
0
1
0
2.500
1
1
0
0
1
1
2.550
1
1
0
1
0
0
2.600
1
1
0
1
0
1
2.650
1
1
0
1
1
0
2.700
1
1
0
1
1
1
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
OUTPUT VOLTAGE
[V]
B5
B4
B3
B2
B1
B0
2.750
1
1
1
0
0
0
2.800
1
1
1
0
0
1
2.850
1
1
1
0
1
0
2.900
1
1
1
0
1
1
3.000
1
1
1
1
0
0
3.100
1
1
1
1
0
1
3.200
1
1
1
1
1
0
3.300
1
1
1
1
1
1
B7
B6
B5
B4
B3
0
0
0
0
0
R
R
R
R
R
DEFSLEW. Register Address: 15h
DEFSLEW
Bit name and function
Default
Default value loaded by:
Read/write
B2
SLEW2
1
UVLO
R/W
B1
SLEW1
1
UVLO
R/W
BO
SLEW0
0
UVLO
R/W
The DEFSLEW register defines the slew rate of the output voltage for DCDC2 and DCDC3 in case the voltage is
changed during operation. In case Bit “LDO2 tracking“ in register DEFLDO2 is set, this is also valid for LDO2.
When the voltage change is initiated by toggling pin DEFDCDC2 or DEFDCDC3, the start of the voltage change
is triggered by the rising or falling edge of the DEFDCDC2 or DEFDCDC3 pin. If a voltage change is done
internally be re-programming register DEFDCDC2_LOW, DEFDCDC2_HIGH, DEFDCDC3_LOW or
DEFDCDC3_HIGH, the voltage change is initiated immediately after the new value has been written to the
register with the slew rate defined.
SLEW2 SLEW SLEW
1
0
VDCDC3
SLEW RATE
0
0
0
0.11 mV/ms
0
0
1
0.22 mV/ms
0
1
0
0.45 mV/ms
0
1
1
0.9 mV/ms
1
0
0
1.8 mV/ms
1
0
1
3.6 mV/ms
1
1
0
7.2 mV/ms
1
1
1
Immediate
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
59
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
LDO_CTRL1. Register Address: 16h
LDO_CTRL1
Bit name and function
Default value loaded by:
Read/write
Bit 7..5
B7
LDO_SQ2
UVLO
R/W
B6
LDO_SQ1
UVLO
R/W
B5
LDO_SQ0
UVLO
R/W
B4
R
B3
LDO1[3]
UVLO
R/W
B2
LDO1[2]
UVLO
R/W
B1
LDO1[1]
UVLO
R/W
BO
LDO1[0]
UVLO
R/W
LDO_SQ2 to LDO_SQ0: power-up sequencing: (power down sequencing is the reverse)
000 = LDO1 and LDO2 are enabled as soon as device is in ON-state by pulling PB_IN=LOW or
POWER_ON=HIGH
001 = LDO1 and LDO2 are enabled after DCDC3 was enabled and its power good Bit is high.
010 = external pin at “EN_EXTLDO” is driven HIGH first, after >1ms LDO2 is enabled, LDO1 is
enabled at the same time with DCDC3. EN_EXTLDO is driven LOW by going into OFF-state, LDO2
is disabled at the same time with EN_EXTLDO going LOW. Disabling LDO2 in register CON_CTRL1
will not drive EN_EXTLDO=LOW. (Atlas4)
011 = LDO1 is enabled 300us after PGOOD of DCDC1, LDO2 is off. LDO2 can be enabled/disabled
by an I2C command in register CON_CTRL1.
100 = LDO1 is enabled after DCDC1 shows power good; LDO2 is enabled with DCDC3
101 = LDO1 is enabled with DCDC2; LDO2 is enabled after DCDC1 is enabled and its power good
Bit is high
110 = LDO1 is enabled 10ms after DCDC2 is enabled and its power good Bit is high, LDO2 is off.
LDO2 can be enabled / disabled by an I2C command in register CON_CTRL1.
111 = external pin at EN_EXTLDO is driven HIGH first, after >1ms LDO2 is enabled, LDO1 is
enabled when EN_DCDC3 pin is pulled high AND DCDC3 is power good (first power–up from OFF
state). LDO1 is disabled when EN_DCDC3 pin goes LOW for SLEEP mode. LDO2 is disabled at the
same time with DCDC2 and DCDC1 during shutdown (Sirf PRIMA).
Automatic sequencing sets the enable Bits of the LDOs accordingly, so the LDOs can be enabled or disabled
by the I2C interface in ON-state.
All sequencing options that define a ramp in sequence for the DCDC converters and the LDOs, (not at the
same time) are timed such that the power good signal triggers the start for the next converter. If there is a time
defined such as 1ms delay, the timer is started after the power good signal of the previous converter is high.
LDO enable is delayed by 170us internally to match the delay for the DCDC converters. By this, for sequencing
options that define a ramp at the same time for an LDO and a DCDC converter, it is made sure they will ramp
at the same time, given the fact the DCDC converters have an internal 170us delay as well.
60
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
Bit 3..0
SLVSAP7 – JANUARY 2011
LDO1(3) to LDO1(0):
The Bits define the default output voltage of LDO1 according to the table below:
LDO1[3]
LDO1[2]
LDO1[1]
LDO1[0]
LDO1 OUTPUT
VOLTAGE
0
0
0
0
1.0 V
0
0
0
1
1.1 V
0
0
1
0
1.2 V
0
0
1
1
1.25 V
0
1
0
0
1.3 V
0
1
0
1
1.35 V
0
1
1
0
1.4 V
0
1
1
1
1.5 V
1
0
0
0
1.6 V
1
0
0
1
1.8 V
1
0
1
0
2.5 V
1
0
1
1
2.75 V
1
1
0
0
2.8 V
1
1
0
1
3.0 V
1
1
1
0
3.1 V
1
1
1
1
3.3 V
DEFLDO2. Register Address: 17h
DEFLDO2
Bit name and function
Default value loaded
by:
Read/write
B7
R
B6
LDO2 tracking
B5
LDO2[5]
B4
LDO2[4]
B3
LDO2[3]
B2
LDO2[2]
B1
LDO2[1]
BO
LDO2[0]
UVLO
UVLO
UVLO
UVLO
UVLO
UVLO
UVLO
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The DEFLDO2 register is used to set the output voltage of LDO2 according to the voltage table defined under
DEFDCDC3 when Bit LDO2 tracking is set to 0. In case Bit LDO2 tracking is set to 1, the output voltage of LDO2
is defined by the contents defined for DCDC3.
Bit 6
LDO2 TRACKING:
0 = the output voltage is defined by register DEFLDO2
1 = the output voltage follows the setting defined for DCDC3 (DEFDCDC3_LOW or
DEFDCDC3_HIGH, depending on the state of pin DEFDCDC3)
Bit 5..0
LDO2[5] to LDO2[0]:
output voltage setting for LDO2 similar to DCDC3
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
61
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
WLED_CTRL1. Register Address: 18h
WLED_CTRL1
Bit name and function
Default
Default value loaded by:
Read/write
B7
Enable
ISINK
0
UVLO
R/W
B6
0
R
B5
Dimming
frequency1
0
UVLO
R/W
B4
Dimming
frequency0
1
UVLO
R/W
B3
B2
B1
BO
0
0
0
0
R
R
R
R
B1
LED DUTY
CYCLE_1
1
UVLO
R/W
BO
LED DUTY
CYCLE_0
0
UVLO
R/W
Bit 7
ENABLE ISINK:
0 = both current sinks are turned OFF, the wLED boost converter is disabled
1 = both current sinks are turned on, the wLED boost converter is enabled
Bit 5..4
DIMMING FREQUENCY 0/1:
00 = 100 Hz
01 = 200 Hz
10 = 500 Hz
11 = 1000 Hz
WLED_CTRL2. Register Address: 19h
WLED_CTRL2
Bit name and function
Default
Default value loaded by:
Read/write
B7
Current
level
0
UVLO
R/W
B6
LED DUTY
CYCLE_6
0
UVLO
R/W
B5
LED DUTY
CYCLE_5
0
UVLO
R/W
B4
LED DUTY
CYCLE_4
1
UVLO
R/W
B3
LED DUTY
CYCLE_3
1
UVLO
R/W
B2
LED DUTY
CYCLE_2
1
UVLO
R/W
Bit 7
CURRENT LEVEL:
0 = current defined with resistor connected from ISET2 to GND
1 = current defined with resistor connected from ISET1 to GND
Bit 6..0
sets the duty cycle for PWM dimming from 1% (0000000) to 100% (1100011).
Values above 1100011 set the duty cycle to 0 %; default is 30% duty cycle
62
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
APPLICATION INFORMATION
STEP-DOWN CONVERTERS
OUTPUT FILTER DESIGN (INDUCTOR AND OUTPUT CAPACITOR)
Inductor Selection
The step-down converters operate typically with 2.2mH output inductor. Larger or smaller inductor values can be
used to optimize the performance of the device for specific operation conditions. The selected inductor has to be
rated for its DC resistance and saturation current. The DC resistance of the inductance will influence directly the
efficiency of the converter. Therefore an inductor with lowest DC resistance should be selected for highest
efficiency.
Equation 4 can be used to calculate the maximum inductor current under static load conditions. The saturation
current of the inductor should be rated higher than the maximum inductor current as calculated with Equation 4.
This is recommended because during heavy load transient the inductor current will rise above the calculated
value.
Vout
1Vin
D IL = Vout ´
L ´ ¦
(4)
ILmax = Ioutmax +
DIL
2
(5)
With
f = Switching Frequency (2.25MHz typical)
L = Inductor Value
ΔIL= Peak to Peak inductor ripple current
ILmax = Maximum Inductor current
The highest inductor current will occur at maximum Vin.
Open core inductors have a soft saturation characteristic and they can usually handle higher inductor currents
versus a comparable shielded inductor.
A more conservative approach is to select the inductor current rating just for the maximum switch current of the
corresponding converter. It must be considered, that the core material from inductor to inductor differs and will
have an impact on the efficiency especially at high switching frequencies.
Refer to Table 4 and the typical applications for possible inductors.
Table 4. Tested Inductors
INDUCTOR TYPE
RECOMMENDED
MAXIMUM DC
CURRENT
INDUCTOR VALUE
SUPPLIER
LPS3010
0.6 A
2.2 mH
Coilcraft
LPS3015
1.2 A
2.2 mH
Coilcraft
LPS4018
1.5 A
2.2 mH
Coilcraft
VLCF4020
1.5 A
2.2 mH
TDK
Output Capacitor Selection
The advanced Fast Response voltage mode control scheme of the two converters allow the use of small ceramic
capacitors with a typical value of 10mF, without having large output voltage under and overshoots during heavy
load transients. Ceramic capacitors having low ESR values result in lowest output voltage ripple and are
therefore recommended. Please refer to for recommended components.
If ceramic output capacitors are used, the capacitor RMS ripple current rating will always meet the application
requirements. Just for completeness the RMS ripple current is calculated as:
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
63
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
Vout
1
Vin ´
L ´ ¦
2 ´ 3
1IRMSCout = Vout ´
(6)
At nominal load current the inductive converters operate in PWM mode and the overall output voltage ripple is
the sum of the voltage spike caused by the output capacitor ESR plus the voltage ripple caused by charging and
discharging the output capacitor:
Vout
1ö
1
Vin ´ æ
DVout = Vout ´
+ ESR ÷
ç
L ´ ¦
è 8 ´ Cout ´ ¦
ø
(7)
Where the highest output voltage ripple occurs at the highest input voltage Vin.
At light load currents the converters operate in Power Save Mode and the output voltage ripple is dependent on
the output capacitor value. The output voltage ripple is set by the internal comparator delay and the external
capacitor. The typical output voltage ripple is less than 1% of the nominal output voltage.
Input Capacitor Selection/Input Voltage
Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is
required for best input voltage filtering and minimizing the interference with other circuits caused by high input
voltage spikes. The converters need a ceramic input capacitor of 10mF. The input capacitor can be increased
without any limit for better input voltage filtering.
The input voltage for the step-down converters needs to be connected to pin VINDCDC1/2 for DCDC1 and
DCDC2 and to pin VINDCDC3 for DCDC3. These pins need to be tied together to the power source on pin SYS
(output of the power path). The 3 step-down converters must not be supplied from different input voltages.
Table 5. Possible Capacitors
22 mF
0805
TDK C2012X5R0J226MT
Ceramic
22 mF
0805
Taiyo Yuden JMK212BJ226MG
Ceramic
10 mF
0805
Taiyo Yuden JMK212BJ106M
Ceramic
10 mF
0805
TDK C2012X5R0J106M
Ceramic
Output Voltage Selection
The DEFDCDC2 and DEFDCDC3 pins are used to set the output voltage for step-down converter DCDC2 and
DCDC3. See table 1 for the default voltages if the pins are pulled to GND or to Vcc.
Voltage Change on DCDC2 and DCDC3
The output voltage of DCDC2 and DCDC3 can be changed during operation from e.g. 1.0V to 1.2V (TPS65070)
and back by toggling the DEFDCDC2 or DEFDCDC3 pin. The status of the DEFDCDC3 pin is sensed during
operation and the voltage is changed as soon as the logic level on this pin changes from low to high or vice
versa.
The output voltage for DCDC2 and DCDC3 can also be changed by changing the register content in registers
DEFDCDC2_LOW, DEFDCDC2_HIGH, DEFDCDC3_LOW and DEFDCDC3_HIGH.
White-LED BOOST CONVERTER
LED-Current Setting/Dimming
The white LED boost converter generates an output voltage, high enough to drive current through up to 10 white
LEDs connected in series. support one or two strings of white LEDs. If two strings of white LEDs are used, the
number of LEDs in each string is limited to 6LEDs due to the switch current limit as defined in the electrical
characteristics. The boost converter block contains two current sinks to control the current through the white
LEDs. The anodes of the “upper” white-LEDs are directly connected to the output voltage at the output capacitor.
The cathode of the “lowest” LED is connected to the input of the current sink at pin ISINK1 or ISINK2. The
internal current sink controls the output voltage of the boost converter such that there is a minimum voltage at
the current sink to regulate the defined current. The maximum current is set with a resistor connected from pin
64
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
ISET1 to GND. Dimming is done with an internal PWM modulator by changing the duty cycle in the current sinks
from 1% to 100%. In order to set a LED current of less than 1% of the current defined at ISET1, a second current
range is set with a resistor at pin ISET2 to GND. By changing between the two current ranges and varying the
duty cycle, it is possible to achieve a dimming ratio of > 1:100. The main functions of the converter like enable /
disable of the converter, PWM duty cycle and dimming frequency are programmed in registers WLED_CTRL1
and WLED_CTRL2 – see the register description for details.
If only one string of white LEDs are used, ISINK1 and ISINK2 need to be connected in parallel.
Setup
In applications not requiring the wLED boost converter, the pins should be tied to a GND as stated below:
Pins L4, FB_wLED, ISINK1 and ISINK2 should be directly connected to GND. Each ISET1 and ISET2 should be
connected to GND with a 100k resistor. Optionally ISET1 and ISET2 can be used as analog inputs to the ADC.
In this case, these pins can be tied to a voltage source in the range from 0V to 2.25V.
Setting the LED Current
There are two resistors which set the default current for the current sinks at ISINK1 and ISINK2.
The resistor connected to ISET1 is used if Bit CURRENT LEVEL is set 1 in register 19h.
The resistor connected to ISET2 is used if Bit CURRENT LEVEL is set 0 in register 19h (default).
This allows switching between two different maximum values for the LED current with one Bit to extend the
resolution for dimming.
Dimming is done by an internal PWM signal that turns on and off the current sinks ISINK1 and ISINK2 at 200Hz
(default). The duty cycle range is 1% to 100% with a 1% resolution and a default duty cycle of 30%. In order to
get the full scale LED current, the PWM dimming needs to be set to 100% in register 19h. This is done by writing
63h to register 19h.
KISET is defined to be 1000 in the electrical spec, the reference voltage at ISET1 and ISET2 is 1.24V.
The current for each string is set by the resistor to:
ISINK1=ISINK2= KISET × 1.24V/RISETx
RISET1, RISET2 = KISET × 1.24V/10mA=124 kΩ
(8)
(8)
(9)
(9)
A resistor value of 124 kΩ sets the current on each string to 10mA.
For one string of wLEDs, both strings need to be connected in parallel, so the current in the wLEDs is twice the
current programmed by the resistor at ISET1 or ISET2.
Connecting both strings in parallel is required because the wLED converter generates its output voltage
dependant on the current in ISINK1 and ISINK2. If the current falls below the target, the output voltage is
increased. If one string is open, the wLED driver will boost the output voltage to its maximum because it
assumes the voltage is not high enough to drive current into this string (there could be different numbers of
wLEDs in the two strings).
Inductor Design
The inductor in a boost converter serves as an energy storage element. The energy stored equals ½ L × I2.
Therefore, the inductor must not be saturated as the inductance will drop and the energy stored will be reduced
causing bad efficiency. The converter operates with typically 15mH to 22mH inductors. A design example for an
application powering 6LEDs in one string given below:
Vin = 2.8 V — minimum input voltage for the boost converter
Vo = 6 × 3.2 V = 19.2 V — assuming a forward voltage of 3.2V per LED
Vf = 0.5 V — forward voltage of the Schottky diode
Io = 25 mA maximum LED current
Fsw = 1.125 MHz — switching frequency — T=890ns
Rds(on) = 0.6R — drain-source resistance of the internal NMOS switch
Vsw — voltage drop at the internal NMOS switch
IAVG — average current in NMOS when turned on
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
65
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
The duty cycle for a boost converter is:
Vo + V ¦ - Vin
D=
Vo + V ¦ - Vsw
(10)
With:
Vsw = Rds(on) ´ IAVG
Iavg =
Io
1 - D
(11)
A different approach to calculate the duty cycle is based on the efficiency of the converter. The typical number
can be found in the graphs, or as a first approach, we can assume to get an efficiency of about 80% as a typical
value.
æ
ö
Vi
D » ç1 - h ´
÷
Vo + V ¦ ø
è
(12)
With the values given above
2.8 V
æ
ö
D » ç 1 - 0.8
÷ » 89%
19.2
V
+
0.5
V
è
ø
(13)
ton = T × D = 890 ns × 0.89 = 792 ns
toff = 890 ns – 792 ns = 98ns
Vsw = Rds(on)
´
IAVG = Rds(on)
Io
25 mA
= 0.6W ´
» 140 mV
1 - D
1 - 0.89
´
(14)
When the NMOS switch is turned on, the input voltage is forcing a current into the inductor. The current slope
can be calculated with:
V L ´ dt
(Vin - Vsw) ´ dt
(2.8V - 0.14V) ´ 792 ns
di =
=
=
= 117 mA
L
L
18 mH
(15)
Iavg =
Io
25 mA
=
= 227 mA
1 - D
1 - 0.89
(16)
The minimum and maximum inductor current can be found by adding half of the inductor current ripple (di) to the
average value, which gives:
117 mA
Imax = 227 mA +
= 285 m A
2
117 mA
Imin = 227 m A = 169 mA
2
(17)
Given the values above, an inductor with a current rating greater than 290mA is needed. Plenty of margin should
be kept to the rating in the inductor vendors data sheets as the maximum current is typically specified at a
inductance drop of 20% or even 30%. A list of tested inductors is given in Table 6 with the test conditions as
mentioned below.
Test conditions:
• Vin = 2.8V
• Vf = 3.2V (per LED)
• Vf = 0.5V (Schottky diode)
• Iout = 25mA per string; no dimming
Table 6. Tested Inductors
66
LED CONFIGURATION
INDUCTOR TYPE
INDUCTOR VALUE
SUPPLIER
1 × 6LEDs
LPS3015
18 mH
Coilcraft
2 × 6LEDs
LPS4018
47 mH
Coilcraft
1 × 10LEDs
LPS4018
47 mH
Coilcraft
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
Other inductors, with lower or higher inductance values can be used. A higher inductance will cause a lower
inductor current ripple and therefore will provide higher efficiency. The boost converter will also stay in
continuous conduction mode over a wider load current range. The energy stored in an inductor is given by
E=1/2L × I2 where I is the peak inductor current. The maximum current in the inductor is limited by the internal
current limit of the device, so the maximum power is given by the minimum peak current limit (see electrical
specifications) times the inductance value. For highest output power, a large inductance value is needed. The
minimum inductor value possible is limited by the energy needed to supply the load. The limit for the minimum
inductor value is given during the on-time of the switch such that the current limit is not reached.
Example for the minimum inductor value:
Vin = 4.2 V, Vout = 19.7 V, Iout = 5 mA, Vsw =0.1 V
→ D = 79%
→ ton = 703 ns
During the on-time, the inductor current should not reach the current limit of 1.4 A.
With V… voltage across the inductor (V = Vin–Vsw)
→ L = V × dt/di = (4.2 V–0.1 V) × 703ns/1.4A = 2mH
Diode Selection
Due to the non-synchronous design of the boost converter, an external diode is needed. For best performance, a
Schottky diode with a voltage rating of 40V or above should be used. A diode such as the MBR0540 with an
average current rating of 0.5A is sufficient.
Output Capacitor Selection
A ceramic capacitor such as X5R or X7R type is required at the output. See Table 7 for reference.
Table 7. Tested Capacitor
LED
CONFIGURATION
TYPICAL VOLTAGE
ACROSS OUTPUT
CAPACITOR
CAPACITOR
VALUE
CAPACITOR
SIZE
2x6LEDs or 1x6LEDs
21 V
4.7 mF / 50 V
1x10LEDs
35 V
4.7 mF / 50 V
CAPACITOR TYPE
MANUFACTURER
1206
UMK316BJ475KL
Taiyo Yuden
1210
GRM32ER71H475KA
Murata
Input Capacitor Selection
A small ceramic input capacitor of 10 mF is needed at the input of the boost converter. If the inductor is directly
connected to the SYS output of , the capacitor can be shared. In this case the capacitance needs to be 22mF or
above. Only X5R or X7R ceramic capacitors should be used.
BATTERY CHARGER
Temperature Sensing
The battery charger integrated in has an over temperature protection for the Li-ion cell. The temperature is
sensed with a NTC located at the battery. Comparators in suspend charge at a temperature below 0°C and
above 45°C. The charger supports two different resistor values for the NTC. The default is internally programmed
to 10k. It is possible to change to a 100k NTC with the I2C interface.
Table 8. NTCs Supported
RESISTANCE AT 25°C
CURVE / B VALUE
RT2 NEEDED FOR
LINEARIZATION
MANUFACTURER
10k
Curve 2 / B=3477
75k
Several
100k
Curve 1 / B=3964
370k
Several
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
67
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
For best performance, the NTC needs to be linearized by connecting a resistor (RT2) in parallel to the NTC as
shown in Figure 46. The resistor value of RT2 needed for linearization can be found in Table 8.
If the battery charger needs to be operated without a NTC connected, e.g. for test purposes, a resistor of 10k or
100k needs to be connected from TS to GND, depending for which NTC is configured to in register
CHCONFIG1.
RT1
TS
2.25 V
RT2
NTC
VHOT(45)
VCOLD(0)
+
+
Figure 45. Linearizing the NTC
Changing the Charging Temperature Range (Default 0°C to 45°C)
The battery charger is designed to operate with the two NTCs listed above. These will give a cold and hot
temperature threshold of 0°C and 45°C. If the charger needs to operate (charge) in a wider temperature range
e.g. –5°C to 50°C, the circuit can be modified accordingly. The NTC changes its resistance based on the
equation listed below:
RNTC (T ) =
æ æ 1 1 öö
ç B´ç ÷
T T 0 ÷ø ø
R 25 ´ eè è
(18)
With:
R25 = NTC resistance at 25°C
T = temperature in Kelvin
T0 = reference temperature (298K)
Resistor RT2 in parallel to the NTC is used to linearize the resistance change with temperature of the NTC. As
the NTC has a high resistance at low temperature, the resulting resistance of NTC in parallel with RT2 is lower
especially for low temperatures where the NTC has a high resistance, so RT2 in parallel has a significant impact.
For higher temperatures, the resistance of the NTC dropped significantly, so RT2 in parallel does not change the
resulting resistance a lot. See Figure 46.
RT1
2.25 V
TS
RT3
RT2
NTC
VHOT(45)
VCOLD(0)
+
+
Figure 46. Changing the Temperature Range
68
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
40000
36000
32000
RNTC (T)
28000
24000
20000
16000
Rp (T)
12000
8000
4000
0
-5
0
5
10 15 20 25 30 35
Temperature - (T)
40 45
50
Figure 47. NTC [R(T)] and NTC in Parallel to RT2 [Rges(T)]
1.8
1.7
1.6
1.5
VTS (T)
1.4
1.3
1.2
1.1
1
0.9
0.8
-5
0
5
10
15 20 25 30 35
Temperature - (T)
40 45
50
Figure 48. Resulting TS Voltage
As Figure 47 shows, the result is an extended charging temperature range at lower temperatures. The upper
temperature limit is shifted to lower values as well resulting in a V(HOT) temperature of slightly less than 45°C.
Therefore RT3 is needed to shift the temperature range to higher temperatures again. Figure 48 shows the result
for:
• RT2 = 47k
• RT3 = 820R
Using these values will extend the temperature range for charging to –5°C to 50°C.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
69
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
POWER SOLUTIONS FOR DIFFERENT APPLICATION PROCESSORS
Default Settings
For proper power supply design with , not only the default output voltage is relevant but also in what sequence
the different power rails are enabled. The voltages are typically enabled internally based on the sequencing
options programmed. For different application processors, there are different sequencing options available. In
addition, the delay time and pulse for the reset signal to the application processor is different. See Table 9 with
the default settings for sequencing, output voltages and reset options for the family:
Table 9. Sequencing Settings
DEDICATED
FOR
DCDC_SQ[2..0]
LDO_SQ[2..0]
COMMENT
Starting
was developed for battery powered applications with focus on lowest shutdown and quiescent current. In order to
achieve this, in shutdown all mayor blocks and the system voltage at the output of the power path (SYS) are
turned off and only the input that turns on , pin PB_IN, is supervised. is designed such that only an ON-key on
PB_IN is needed pulling this pin LOW to enable . No external pull-up is needed as this is integrated into .
Once PB_IN is pulled LOW, the system voltage is ramped and the dcdc converters and LDOs are started with
the sequencing defined for the version used. If PB_IN is released again, TPS6507x would turn off, so a pin was
introduced to keep TPS6507x enabled after PB_IN was released. Pin POWER_ON serves this function and
needs to be pulled HIGH before the user releases the ON-key (PB_IN = HIGH). This HIGH signal at
POWER_ON can be provided by the GPIO of a processor or by a pull-up resistor to any voltage in the system
which is higher than 1.2V. Pulling POWER-ON to a supply voltage would significantly reduce the time PB_IN has
to be asserted LOW. If POWER_ON is tied to a GPIO, the processor has to boot up first which may take some
time. In this case however, the processor could do some additional debouncing, hence does not keep the power
enabled if the ON-key is only pressed for a short time. When there is a supply voltage for the battery charger at
pins AC or USB, the situation is slightly different. In this case, the power path is enabled and the system voltage
(SYS) has ramped already to whatever the voltage at AC or USB is. The dcdc converters are not enabled yet but
the start-up could not only be done by pulling PB_IN=LOW but also by pulling POWER_ON=HIGH.
In applications that do not require an ON-key but shall power-up automatically once supply voltage is applied,
there are two cases to consider. If TPS6507x is powered from its AC or USB pin (not powered from its BAT pin),
POWER-ON just needs to be pulled HIGH to enable the converters. PB_IN must not be tied LOW in this case.
If TPS6507x is powered from its BAT pin, PB_IN needs to be tied LOW to start-up the converters.
Layout Considerations
As for all switching power supplies, the layout is an important step in the design. Proper function of the device
demands careful attention to PCB layout. Care must be taken in board layout to get the specified performance. If
the layout is not carefully done, the regulators may show poor line and/or load regulation, and stability issues as
well as EMI problems. It is critical to provide a low impedance ground path. Therefore, use wide and short traces
for the main current paths. The input capacitors should be placed as close as possible to the IC pins as well as
the inductor and output capacitor.
For TPS6507x, connect the PGND pin of the device to the PowerPAD™ land of the PCB and connect the analog
ground connection (GND) to the PGND at the PowerPAD™. The PowerPAD™ serves as the power ground
connection for the DCDC1 and DCDC2 converters. Therefore it is essential to provide a good thermal and
electrical connection to GND using multiple vias to the GND-plane. Keep the common path to the GND pin,
which returns the small signal components, and the high current of the output capacitors as short as possible to
avoid ground noise. The VDCDCx line should be connected right to the output capacitor and routed away from
noisy components and traces (for example, the L1, L2, L3 and L4 traces). See the EVM users guide for details
about the layout for TPS6507x.
70
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
APPLICATION CIRCUITS
TPS65070
AC
BAT
BAT
1 mF
charger / power
path
USB
1 mF
LiIon
TS
SYS
NTC
Vin
BYPASS
DEFDCDC2
L1
SYS
sets default
voltage of
DCDC3 to
1.0 V or 1.2 V
DCDC1
600 mA
DEFDCDC3
AVDD6
EN
10 mF
2.2 mH
USB0_VDDA33 (3.3 V)
USB1_VDDA33 (3.3 V)
VDCDC1
TPS3805H33
10 mF
VDD
SYS
EN_DCDC1
Sense
Reset
VINLDO1/2
SYS
RTC_CVDD (1.2V)
VINDCDC3
set charge
current
SYS
sets default
voltage of
DCDC2 to
1.8 V or 3.3 V
LDO
VINDCDC1/2
ISET
OMAP-L138
TPS78101
22 mF
L2
1 mF
DCDC2
1500 mA
INT_LDO
2.2 mF
VDCDC2
L3
AVDD6
DCDC3
1500 mA
PB_IN
LDO2
200 mA
2.2 mH
DVDD3318_A (3.3V or 1.8 V)
DVDD3318_B (3.3V or 1.8 V)
10 mF
DVDD3318_C (3.3V or 1.8 V)
2.2 mH
CVDD (1.2 V)
10 mF
VDCDC3
4.7 mF
SATA_VDD (1.2 V)
VLDO2
ON
PLL0_VDDA (1.2 V)
PLL1_VDDA (1.2 V)
2.2 mF
USBs CVDD (1.2 V)
EN_DCDC2
L4
SYS
2.2 mF
VDDARNWA/1 (1.2 V)
SATA_VDDR (1.8 V)
10 kW
EN_DCDC3
Si2333
VLDO1
100 kW
LDO1
200 mA
USB0_VDDA18 (1.8 V)
1 mF
USB1_VDDA18 (1.8 V)
DDR_DVDD18 (1.8 V)
FB_wLED
PGND
1 mF
BC847
ISINK1
VDDIO
wLED
boost
PowerPad(TM)
ISINK2
ISET1
AD_IN1(TSX1)
100 kW
100 kW
3.3 kW
3.3 kW
RESET
SDAT
SDAT
INT
POWER_ON
AD_IN3(TSY1)
AD_IN4(TSY2)
+
PB_INTERRUPT
PGOOD
SCLK
AD_IN2(TSX2)
THRESHOLD
100 kW
PB_OUT
100 kW
AGND
ISET2
SCLK
INT
GPIO (power hold)
Reset
delay
Figure 49. Powering OMAP-L138
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
71
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
PB_IN
can be released HIGH any time
after POWR_ON = HIGH
PB_OUT
level not defined as
voltage at pull-up has
not ramped at that time
50ms debounce
50 ms debounce
SYS
POWER_ON
asserted HIGH by the application processor
any time while PB_IN = LOW to keep the
system alive
external LDO
(RTC_CVDD)
1.2 V
VDCDC3
(CVDD)
1.2 V
170 ms
250 ms
VLDO2
(SATA_VDD)
1.2 V
VDCDC2
(VDDSHV)
1.8 V
170 ms
250 ms
VLDO1
(SATA_VDDR)
1.8 V
VDCDC1
(USB0_VDDA33)
3.3 V
250 ms
170 ms
PGOOD
(Reset)
400 ms
Figure 50. Timing for OMAP-L138
72
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
AC
BAT
TPS65072
BAT
1 mF
USB
charger / power path
LiIon
TS
NTC
SYS
1 mF
VINDCDC1/2
ISET
2 x 10 mF
VINDCDC3
set
charge
current
BYPASS (2.25 V reference output)
DEFDCDC2
ALTAS IV
L1
DEFDCDC3
DCDC1
600 mA
VINLDO1/2
SYS
1 mF
2.2 mH
VCC_3V3 (VDDIO)
VDCDC1
10 mF
L2 2.2 mH
DCDC2
600 mA
INT_LDO
VCC_1V8 (VDDIO_MEM)
VDCDC2
2.2 mF
L3
DCDC3
600 mA
AVDD6
4.7 mF
10 mF
2.2 mH
VDD_PDN (1.2 V)
VDCDC3
10 mF
VLDO2
/PB_IN
VDD_PRE (1.2 V)
LDO2
200 mA
2.2 mF
LDO1
200 mA
2.2 mF
ON /
OFF
VDDPLL (1.2 V)
EN_DCDC1
VIN
SYS
EN_DCDC2
EN_EXTLDO
L4
SYS
LDO
EN
EN_wLED
FB_wLED
1 mF
ISINK1
GPIO (enable wLED)
GPIO (power hold)
POWER_ON
wLED
boost
VDD_RTCIO
EN_DCDC3
X_PWR_EN
VIO
ISET1
ISET2
PB_OUT
4.7k
4.7k
ISINK2
PGOOD
SDAT
SCLK
INT
PB_INTERRUPT
RESET
SDAT
SCLK
INT
Note: /Reset to Atlas 4 may need to
be a RC delay from VDDIO
Figure 51. Powering Atlas IV
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
73
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
PB_IN
can be released HIGH any time
after POWR_ON=HIGH
15s
PB_OUT
level not defined as
voltage at pull-up has
not ramped at that time
50ms debounce
50ms debounce
SYS
POWER_ON
asserted HIGH by the application processor
any time while /PB_IN=LOW to keep the
system alive
EN_EXTLDO
(VDD_RTCIO)
VLDO2
(VDD_PRE)
VDCDC1
(VCC_3V3)
1ms
0.95 x Vout,nominal
1ms
0.95 x Vout,nominal
1ms
250 ms
1ms
250 ms
VDCDC2
(VCC_1V8)
EN_DCDC3
(X_PWR_EN)
VDCDC3
(VDD_PDN)
170 ms
VLDO1
(VDDPLL)
250 ms
170 ms
250 ms
PGOOD
(X_RESET_B)
20ms
0.5ms
Figure 52. Timing for Atlas IV
74
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
Prima SLEEP Mode and DEEP SLEEP Mode Support
TPS6507x contains a sequencing option for the Sirf Prima processor. The sequencing option defines how the
voltages are ramped at initial power-up and shutdown as well as the timing for entering power save mode for the
processor (SLEEP mode). The Prima processor supports SLEEP mode and also DEEP SLEEP mode. The main
difference from a power supply point of view is:
• How the supply voltages are turned off
• Which voltages are turned off
• How power save mode is exited into normal mode
• Reset asserted or not (PGOOD pin of TPS6507x going actively low)
The sequencing option for Prima is defined in one register each for the sequencing of the DCDC converters and
for the LDOs. DCDC_SQ[2..0]=100 in register CON_CTRL1 defines the startup sequence for the DCDC
converters while LDO_SQ[2..0]=111 defines the sequence for the LDOs. The default is factory programmed
therefore it is ensured the first power-up is done in the right sequence.
When TPS6507x is off, a small state machine supervises the status of pin PB_IN while major blocks are not
powered for minimum current consumption from the battery as long as there is no input voltage to the charger.
Power-up for the TPS6507x is started by PB_IN going LOW. This will turn on the power-FET from the battery so
the system voltage (SYS) is rising and the main blocks of the PMU are powered. After a debounce time of 50ms,
the main state machine will pull PB_OUT = LOW to indicate that there is a “keypress” by the user and will ramp
the DCDC converters and LDOs according to the sequence programmed. It is important to connect the power
rails for the processor to exactly the dcdc converters and LDOs as shown in the schematic and sequencing
diagrams for proper sequencing. For Prima, the voltage rails for VDD_RTCIO needs to ramp first. This power rail
is not provided by the PMU but from an external LDO which is enabled by a signal called EN_EXTLDO from the
PMU. The PMU will therefore first rise the logic level an pin EN_EXTLDO high to enable the external LDO. After
a 1ms delay the PMU will ramp LDO2 for VDD_PRE and DCDC3 for VDD_PDN. When the output voltage of
LDO2 is within it s nominal range the internal power good comparator will trigger the state machine which will
ramp DCDC1 and DCDC2 to provide the supply voltage for VCC_3V3 and VCC_1V8. Now Prima needs to pull
its X_PWR_EN signal high which drives EN_DCDC3 on the PMU. This will now enable LDO1 to power VDDPLL.
X_RESET_B will be released by the PMU on pin PGOOD based on the voltage of DCDC1 after a delay of 20ms.
SLEEP Mode
At first power-up (start-up from OFF state), the voltage for VDD_PDN is ramped at the same time than
VDD_PRE. This is defined by Bit MASK_EN_DCDC3 in register CON_CTRL2 which is “1” per default. For
enabling SLEEP mode, Prima needs to clear this Bit, so the EN_DCDC3 pin takes control over the DCDC3
converter. Prima SLEEP mode is initialized by Prima pulling its X_PWR_EN pin LOW which is driving the
EN_DCDC3 pin of TPS6507x. This will turn off the power for VDDPLL (LDO1) and also for VDD_PDN (DCDC3).
All other voltage rails will stay on. Based on a “keypress” with PB_OUT going LOW, Prima will wake up and
assert EN_DCDC3=HIGH. This will turn DCDC3 and LDO1 back on and Sirf PRIMA will enter normal operating
mode.
DEEP SLEEP Mode
Entry into DEEP SLEEP mode is controlled by Prima by writing to register CON_CTRL2 of TPS6507x. Before
entering DEEP SLEEP mode, Prima will back up all memory and set Bit DS_RDY=1 to indicate the memory was
saved and the content is valid. Setting PWR_DS=1 will turn off all voltage rails except DCDC2 for the memory
voltage and the PMU will apply a reset signal by pulling PGOOD=LOW. Prima can not detect logic level change
by PB_OUT going low in DEEP SLEEP mode. A wakeup from DEEP sleep is therefore managed by the PMU.
The PMU will clear Bit PWR_DS and turn on the converters again based on a user “keypress” when PB_IN is
being pulled LOW. Prima will now check if DS_RDY=1 to determine if the memory content is still valid and clear
the Bit afterwards. In case there is a power loss and the voltage of the PMU is dropping below the undervoltage
lockout threshold, the registers in the PMU are re-set to the default and DS_RDY is cleared. The PMU would
perform a start-up from OFF state instead of exit from DEEP SLEEP and Sirf PRIMA would read DS_RDY=0,
which indicates memory data is not valid.
See timing diagrams for Sirf Prima SLEEP and DEEP SLEEP in Figure 53 and Figure 54.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
75
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
PB_IN
can be released HIGH any time
after POWR_ON=HIGH
15s
PB_OUT
level not defined as
voltage at pull-up has
not ramped at that time
50ms debounce
50ms debounce
SYS
POWER_ON
asserted HIGH by the application processor
any time while /PB_IN=LOW to keep the
system alive
EN_EXTLDO
(VDD_RTCIO)
VLDO2
(VDD_PRE)
1ms
0.95 x Vout,nominal
1ms
VDCDC1
(VCC_3V3)
0.95 x Vout,nominal
250 ms
170 ms
VDCDC2
(VCC_1V8)
250 ms
170 ms
Bit
MASK_EN_DCDC3
Bit MASK_EN_DCDC3 is cleared by the application processor.
DCDC3 and LDO1 are enabled / disabled by EN_DCDC3 to
enter / exit SLEEP mode
EN_DCDC3
(X_PWR_EN)
VDCDC3
(VDD_PDN)
Bit MASK_EN_DCDC3 is
set per default. DCDC3 is
startted with LDO2
170 ms
VLDO1
(VDDPLL)
170 ms
250 ms
250 ms
170 ms
PGOOD
(X_RESET_B)
20ms
0.5ms
Figure 53. Timing for Sirf Prima SLEEP Mode
76
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
PB_IN
can be released HIGH any time
after POWR_ON=HIGH
startup from OFF state
PB_OUT
wakeup
from
DEEP
SLEEP
level not defined as
voltage at pull-up has
not ramped at that time
50ms debounce
50ms debounce
SYS
POWER_ON
asserted HIGH by the application processor
any time while /PB_IN=LOW to keep the
system alive
EN_EXTLDO
(VDD_RTCIO)
VLDO2
(VDD_PRE)
VDCDC1
(VCC_3V3)
1ms
0.95 x Vout,nominal
0.95 x Vout,nominal
1ms
0.95 x Vout,nominal
250 ms
170 ms
VDCDC2
(VCC_1V8)
250 ms
170 ms
Bit
MASK_EN_DCDC3
set Bits DS_RDY to indicate
memory was backed-up
Bit
DS_RDY
Bit
PWR_DS
DS_RDY=0, start with
initial power-up sequence
DS_RDY=1, start wake-up sequence;
otherwise start initial power-up from OFF state
set Bits PWR_DS to set Titan 2
to DEEP SLEEP mode
DS_RDY is
cleared by user
software
PWR_DS is
cleared by
PB_IN going
LOW
EN_DCDC3
(driven from
VDCDC1)
VDCDC3 Bit MASK_EN_DCDC3 is
(VDD_PDN) set per default. DCDC3 is
startted at the same time
with LDO2
VLDO1
(VDDPLL)
PGOOD
(X_RESET_B)
20ms
20ms
Figure 54. Timing for Sirf Prima DEEP SLEEP Mode
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
77
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
TPS65073
AC
1uF
BAT
USB
charger / power path
1uF
VDDS_MMC1(1.8V / 3.0V)
LiIon
TS
NTC
SYS
ISET
VINDCDC1/2
set charge
current
VINDCDC3
2 x 10uF
1.5uH
L1
DEFDCDC2
DCDC1
600mA
DEFDCDC3
SYS
OMAP35xx
TPS79901
Vin
SYS
LDO
EN
BAT
VINLDO1/2
VDCDC1
L2
1uF
DCDC2
600mA
L3
ON /
OFF
DCDC3
1500mA
AVDD6
1.5uH
VDDCORE (1.2V)
VDCDC2
/PB_IN
VDDS_WKUP_BG (1.8V)
VDDS_MEM; VDDS
VDDS_SRAM
10uF
10uF
1.5uH
VDD_MPU_IVA (1.2V)
VDCDC3
10uF
LDO2
LDO2
200mA
AD_IN1 (TSX1)
VDDA_DAC (1.8V)
2.2uF
LDO1
AD_IN2 (TSX2)
LDO1
200mA
AD_IN3 (TSY1)
AD_IN4 (TSY2)
VDDS_DPLL_DLL (1.8V)
VDDS_DPLL_PER (1.8V)
2.2uF
VDDS
EN_DCDC1
BYPASS
SYS
SN74LVC1G06DCK
VDDS VCC
INT_LDO
EN_DCDC2
TPS3825-33DBVT
VDD
/RST
/MR
L4
SYS
SYS
EN_DCDC3
Y
A
SYS_OFF_MODE
GND
VDDS
GND
FB_wLED
1uF
PB_OUT
100k
4.7k
4.7k
100k
wLED
boost
100k
100kk
ISINK1
POWER_ON
ISINK2
PGOOD
ISET1
SDAT
ISET2
SCLK
/INT
THRESHOLD
GPIO (push-button int)
GPIO (/disable power)
SYS.nRESPWRON
SDAT
SCLK
/INT
/Reset
+
delay
Figure 55. OMAP35xx (Supporting SYS-OFF Mode)
78
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
PB_IN
can be released HIGH any time
after POWR_ON=HIGH
PB_OUT
level not defined as
voltage at pull-up has
not ramped at that time
50ms debounce
SYS
POWER_ON
asserted HIGH by the application processor (OMAP)
any time while /PB_IN=LOW to keep the system alive
VDCDC1
(VDDS_WKUP_BG,
VDDS, VDDS_MEM
)
250 ms
170 ms +
RC delay
VDCDC2
(VDD_CORE)
170 ms +
RC delay
250 ms
VDCDC3
(VDD_MPU_IVA)
VLDO1
250 ms
170 ms +
RCdelay
(VDDS_DPLL_DLL,
VDDS_DPLL_PER)
VLDO2
(VDDA_DAC)
PGOOD
(SYS.nRESPWRON)
400ms
Figure 56. OMAP35xx Timing (Supporting SYS-OFF Mode)
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
79
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
TPS650731
BAT
AC
BAT
1 mF
USB
charger / power path
NTC
SYS
1 mF
VINDCDC1/2
ISET
VINDCDC3
set
charge
current
L1
DCDC1
600mA
DEFDCDC2
OMAP35xx
2 x 10 mF
2.2 mH
VDCDC1
VDDS_WKUP_BG (1.8 V)
VDDS_MEM; VDDS
10 mF
VDDS_SRAM
DEFDCDC3
L2
SYS
LiIon
TS
DCDC2
600mA
VINLDO1/2
2.2 mH
VDDCORE (1.2 V)
VDCDC2
10 mF
2.2 mH
1uF
L3
DCDC3
1500mA
VDD_MPU_IVA (1.2 V)
VDCDC3
10 mF
LDO2
PB_IN
LDO2
200mA
ON /
OFF
VDDA_DAC (1.8 V)
2.2 mF
VDDDLL
VDDS_DPLL_DLL (1.8 V)
VDDS_DPLL_PER (1.8 V)
LDO1
LDO1
200mA
AD_IN1 (TSX1)
AD_IN2 (TSX2)
2.2 mF
VIO
AD_IN3 (TSY1)
EN_DCDC1
AD_IN4 (TSY2)
EN_DCDC2
SYS
POWER_ON
FB_wLED
PGOOD
1 mF
SDAT
ISINK1
SCLK
wLED
boost
/INT
4.7k
1M
PB_OUT
1M
4.7 k
L4
SYS
100 K
EN_DCDC3
GPIO (/disable power)
SYS.nRESPWRON
SDAT
SCLK
/INT
AVDD6
ISINK2
ISET1
ISET2
BYPASS
INT_LDO
THRESHOLD
/Reset
+
delay
Figure 57. TPS650731 for OMAP35xx
80
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
PB_IN
can be released HIGH any time
after POWR_ON=HIGH
PB_OUT
level not defined as
voltage at pull-up has
not ramped at that time
50ms debounce
50ms debounce
SYS
POWER_ON
asserted HIGH by the application processor
any time while /PB_IN=LOW to keep the
system alive
VDCDC1
(VDDS_WKUP_BG,
VDDS, VDDS_MEM
)
250 ms
170 ms
VDCDC2
(VDD_CORE)
170 ms
250 ms
VDCDC3
(VDD_MPU_IVA)
250 ms
170 ms
VLDO1
(VDDS_DPLL_DLL,
VDDS_DPLL_PER)
VLDO2
300 ms
(VDDA_DAC)
enabled by OMAP35xx by I2C command
PGOOD
(SYS.nRESPWRON)
400ms
Figure 58. TPS650731: OMAP35xx timing
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
81
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
SLVSAP7 – JANUARY 2011
www.ti.com
TPS650732
BAT
AC
BAT
1uF
USB
charger / power path
1uF
SYS
ISET
VINDCDC3
VDDS1-5 (1.8V)
VDCDC1
DEFDCDC3
VINLDO1/2
10uF
2.2uH
L2
DCDC2
600mA
AM3505
2 x 10uF
2.2uH
L1
DCDC1
600mA
DEFDCDC2
SYS
NTC
VINDCDC1/2
set
charge
current
SYS
LiIon
TS
VDDSHV (3.3V)
VDCDC2
10uF
2.2uH
1uF
L3
DCDC3
1500mA
/PB_IN
VDD_CORE (1.2V)
VDCDC3
10uF
LDO2
LDO2
200mA
ON /
OFF
VDDS_DPLL (1.8V)
2.2uF
LDO1
LDO1
200mA
AD_IN1 (TSX1)
AD_IN2 (TSX2)
VDDA1P8V(1.8V)
2.2uF
AD_IN3 (TSY1)
EN_DCDC1
AD_IN4 (TSY2)
EN_DCDC2
SYS
1uF
GPIO (/disable power)
SYS.nRESPWRON
SDAT
SCLK
/INT
PGOOD
SDAT
ISINK1
SCLK
wLED
boost
1M
4.7 k
POWER_ON
FB_wLED
1M
PB_OUT
4.7 k
SYS
100K
EN_DCDC3
L4
/INT
AVDD6
ISINK2
ISET1
ISET2
BYPASS
SYS
TPS79918
Vin
EN
VDDS_SRAM (1.8V)
LDO
INT_LDO
THRESHOLD
/Reset
+
delay
SYS
TPS79933
Vin
VDDA3P3V (3.3V)
LDO
EN
Figure 59. Powering AM3505 Using TPS650732
82
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
TPS65070-Q1, TPS65072-Q1, TPS65073-Q1, TPS650732-Q1
www.ti.com
SLVSAP7 – JANUARY 2011
/PB_IN
can be released HIGH any time
after POWR_ON=HIGH
PB_OUT
level not defined as
voltage at pull-up has
not ramped at that time
50ms debounce
50ms debounce
SYS
POWER_ON
asserted HIGH by the application processor
any time while /PB_IN=LOW to keep the
system alive
VDCDC1
(VDDS1-5
1.8V
)
170us
250us
VDCDC2
(VDDSHV)
3.3V
170us
250us
VLDO_ext1
(VDDS_SRAM)
1.8V
VDCDC3
(VDD_CORE)
1.2V
250us
170us
VLDO2
(VDDS_DPLL)
1.8V
VLDO1
(VDDA1P8V)
1.8V
VLDO_ext2
(VDDA3P3V)
3.3V
PGOOD
(SYS.nRESPWRON)
400ms
Figure 60. Timing Using TPS650732 for AM3505
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s) :TPS65070-Q1 TPS65072-Q1 TPS65073-Q1 TPS650732-Q1
83
PACKAGE OPTION ADDENDUM
www.ti.com
19-Sep-2011
PACKAGING INFORMATION
Orderable Device
TPS650732TRSLRQ1
Status
(1)
Package Type Package
Drawing
ACTIVE
VQFN
RSL
Pins
Package Qty
48
2500
Eco Plan
(2)
Green (RoHS
& no Sb/Br)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
CU NIPDAU Level-3-260C-168 HR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS650732-Q1 :
• Catalog: TPS650732
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TPS650732TRSLRQ1
Package Package Pins
Type Drawing
VQFN
RSL
48
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
16.4
Pack Materials-Page 1
6.3
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
6.3
1.1
12.0
16.0
Q2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS650732TRSLRQ1
VQFN
RSL
48
2500
367.0
367.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated