PCM1690 Burr-Brown Audio www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 24-Bit, 192-kHz Sampling, Enhanced Multi-Level ΔΣ, Eight-Channel Audio Digital-to-Analog Converter FEATURES 1 • 24-Bit Delta-Sigma DAC • 8-Channel DAC: – High Performance: Differential, fS = 48 kHz – THD+N: –94 dB – SNR: 113 dB – Dynamic Range: 113 dB – Sampling Rate: 8 kHz to 192 kHz – System Clock: 128 fS, 192 fS, 256 fS, 384 fS, 512 fS, 768 fS, 1152 fS – Differential Voltage Output: 8 VPP – Analog Low-Pass Filter Included – 4x/8x Oversampling Digital Filter: – Passband Ripple: ±0.0018 dB – Stop Band Attenuation: –75 dB – Zero Flag • Flexible Audio Interface: – I/F Format: I2S™, Left-/Right-Justified, DSP, TDM – Data Length: 16, 20, 24, 32 Bits • Flexible Mode Control: – 3-Wire SPI™, 2-Wire I2C™-Compatible Serial Control Interface, or Hardware Control • Multi Functions via SPI or I2C I/F: – Audio I/F Format Select: I2S, Left-Justified, Right-Justified, DSP, TDM – Digital Attenuation and Soft Mute – Digital De-Emphasis: 32 kHz, 44.1 kHz, 48 kHz – Data Polarity Control – Power Down • Multi Functions via H/W Control: – Audio I/F Format Select: I2S, TDM – Digital De-Emphasis Filter: 44.1 kHz • Analog Mute by Clock Halt Detection • External RESET Pin • 2345 • • Power Supplies: – 5 V for Analog and 3.3 V for Digital Package: HTSSOP-48 Operating Temperature Range: – –40°C to +85°C APPLICATIONS • • • • • • Blu-ray™ DVD Players HD DVD Players AV Receivers Home Theaters Car Audio External Amplifiers Car Audio AVN Applications DESCRIPTION The PCM1690 is a high-performance, single-chip, 24-bit, eight-channel, audio digital-to-analog converter (DAC) with differential outputs. The eight-channel, 24-bit DAC employs an enhanced, multi-level delta-sigma (ΔΣ) modulator and supports 8-kHz to 192-kHz sampling rates and a 16-/20-/24-/32-bit width digital audio input word on the audio interface. The audio interface of the PCM1690 supports the time-division-multiplexed (TDM) format in addition to the standard I2S, left-justified, right-justified, and DSP formats. The PCM1690 can be controlled through a three-wire, SPI-compatible interface, or two-wire, I2C-compatible serial interface in software, which provides access to all functions including digital attenuation, soft mute, de-emphasis, and so forth. Also, hardware control mode provides a subset of user-programmable functions through two control pins. The PCM1690 is available in a 12-mm × 8-mm (12-mm × 6-mm body) HTSSOP-48 package. 1 2 3 4 5 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Blu-ray is a trademark of Blu-ray Disk Association. SPI is a trademark of Motorola. I2S, I2C are trademarks of NXP Semiconductors. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2008, Texas Instruments Incorporated PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION (1) (1) PRODUCT PACKAGELEAD PACKAGE DESIGNATOR SPECIFIED TEMPERATURE RANGE PACKAGE MARKING PCM1690 HTSSOP-48 DCA –40°C to +85°C PCM1690 ORDERING NUMBER TRANSPORT MEDIA, QUANTITY PCM1690DCA Tube, 40 PCM1690DCAR Tape and Reel, 2000 For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) Over operating free-air temperature range (unless otherwise noted). PARAMETER PCM1690 UNIT Supply voltage: VCC1, VCC2 –0.3 to +6.5 V Supply voltage: VDD –0.3 to +4.0 V Ground voltage differences: AGND1, AGND2, DGND ±0.1 V Supply voltage differences: VCC1, VCC2 ±0.1 V Digital input voltage: RST, TEST, MS, MC, MD, SCKI, AMUTEI, AMUTEO –0.3 to +6.5 V Digital input voltage: BCK, LRCK, DIN1/2/3/4, MODE, ZERO1, ZERO2 –0.3 to (VDD + 0.3) < +4.0 V Analog input voltage: VCOM, VOUT1–8± –0.3 to (VCC + 0.3) < +6.5 V ±10 mA Ambient temperature under bias –40 to +125 °C Storage temperature –55 to +150 °C Junction temperature +150 °C Lead temperature (soldering, 5s) +260 °C Package temperature (IR reflow, peak) +260 °C Input current (all pins except supplies) (1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS Over operating free-air temperature range (unless otherwise noted). PCM1690 PARAMETER MIN TYP MAX UNIT Analog supply voltage, VCC 4.5 5.0 5.5 V Digital supply voltage, VDD 3.0 3.3 3.6 V Digital Interface Digital input clock frequency Analog output voltage Analog output load resistance LVTTL compatible Sampling frequency, LRCK System clock frequency, SCKI 8 192 kHz 2.048 36.864 MHz Differential 8 To ac-coupled GND 5 To dc-coupled GND 15 VPP kΩ kΩ Analog output load capacitance 50 pF Digital output load capacitance 20 pF +85 °C Operating free-air temperature 2 PCM1690 consumer grade Submit Documentation Feedback –40 +25 Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 ELECTRICAL CHARACTERISTICS: Digital Input/Output All specifications at TA = +25°C, VCC1 = VCC2 = 5 V, VDD = 3.3 V, fS = 48 kHz, SCKI = 512 fS, 24-bit data, and Sampling Mode = Auto, unless otherwise noted. PCM1690 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT DATA FORMAT I2S, LJ, RJ, DSP, TDM Audio data interface format 16, 20, 24, 32 Audio data word length Audio data format Bits MSB first, twos complement Sampling frequency fS 8 128 fS, 192 fS, 256 fS, 384 fS, 512 fS, 768 fS, 1152 fS System clock frequency 48 192 kHz 2.048 36.864 MHz 2.0 VDD VDC 0.8 VDC 5.5 VDC INPUT LOGIC Input logic level Input logic level Input logic current Input logic current VIH (1) (2) VIL (1) (2) VIH (3) (4) VIL 2.0 (3) (4) 0.8 VDC IIH (2) (3) VIN = VDD ±10 µA IIL (2) (3) VIN = 0 V ±10 µA +100 µA ±10 µA IIH (1) (4) VIN = VDD IIL (1) (4) VIN = 0 V VOH (5) IOUT = –4 mA (5) (6) IOUT = +4 mA +65 OUTPUT LOGIC Output logic level VOL 2.4 VDC 0.4 VDC REFERENCE OUTPUT 0.5 × VCC1 VCOM output voltage VCOM output impedance 7.5 Allowable VCOM output source/sink current (1) (2) (3) (4) (5) (6) V kΩ 1 µA BCK and LRCK (Schmitt trigger input with 50-kΩ typical internal pull-down resistor). DIN1/2/3/4 (Schmitt trigger input). SCKI, TEST/ADR1/RSV, MC/SCL/FMT, MD/SDA/DEMP, and AMUTEI (Schmitt trigger input, 5-V tolerant). RST and MS/ADR0/RSV (Schmitt trigger input with 50-kΩ typical internal pull-down resistor, 5-V tolerant). ZERO1 and ZERO2. SDA (I2C mode, open-drain low output) and AMUTEO (open-drain low output). Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 3 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com ELECTRICAL CHARACTERISTICS: DAC All specifications at TA = +25°C, VCC1 = VCC2 = 5 V, VDD = 3.3 V, fS = 48 kHz, SCKI = 512 fS, 24-bit data, and Sampling Mode = Auto, unless otherwise noted. PCM1690 PARAMETER TEST CONDITIONS MIN TYP 16 24 MAX UNIT DAC CHARACTERISTICS Resolution Bits DC ACCURACY Gain mismatch channel-to-channel ±2.0 ±6 % of FSR Gain error ±2.0 ±6 % of FSR Bipolar zero error ±1.0 % of FSR DYNAMIC PERFORMANCE (1) (2) Total harmonic distortion + noise THD+N fS = 48 kHz, VOUT = 0 dB –94 fS = 96 kHz, VOUT = 0 dB –94 dB fS = 192 kHz, VOUT = 0 dB –94 dB 113 dB 113 dB 113 dB 113 dB 113 dB 113 dB 109 dB fS = 96 kHz 109 dB fS = 192 kHz 108 dB Differential 1.6 × VCC1 VPP 0.5 × VCC1 V fS = 48 kHz, EIAJ, A-weighted Dynamic range 106 fS = 96 kHz, EIAJ, A-weighted fS = 192 kHz, EIAJ, A-weighted fS = 48 kHz, EIAJ, A-weighted Sighnal-to-noise ratio SNR 106 fS = 96 kHz, EIAJ, A-weighted fS = 192 kHz, EIAJ, A-weighted fS = 48 kHz Channel separation (between one channel and others) 103 –88 dB ANALOG OUTPUT Output voltage Center voltage Load impedance To ac-coupled GND (3) 5 To dc-coupled GND (3) 15 LPF frequency response kΩ kΩ f = 20 kHz –0.04 dB f = 44 kHz –0.18 dB DIGITAL FILTER PERFORMANCE WITH SHARP ROLL-OFF Passband (single, dual) Except SCKI = 128 fS and 192 fS 0.454 × fS Hz SCKI = 128 fS and 192 fS 0.432 × fS Hz 0.432 × fS Hz Passband (quad) Stop band (single, dual) Except SCKI = 128 fS and 192 fS 0.546 × fS Hz SCKI = 128 fS and 192 fS 0.569 × fS Hz 0.569 × fS Hz Stop band (quad) Passband ripple < 0.454 × fS, 0.432 × fS Stop band attenuation > 0.546 × fS, 0.569 × fS (1) (2) (3) 4 ±0.0018 –75 dB dB In differential mode at VOUTx± pin, fOUT = 1 kHz, using Audio Precision System II, Average mode with 20-kHz LPF and 400-Hz HPF. fS = 48 kHz: SCKI = 512 fS (single), fS = 96 kHz : SCKI = 256 fS (dual), fS = 192 kHz : SCKI = 128 fS (quad). Allowable minimum input resistance of differential to single-ended converter with D to S Gain = G is calculated as (1 + 2G)/(1 + G) × 5k for ac-coupled and (1+ 0.9G)/(1 + G) × 15k for dc-coupled connection; refer to Figure 41 and Figure 42 of the Application Information section. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 ELECTRICAL CHARACTERISTICS: DAC (continued) All specifications at TA = +25°C, VCC1 = VCC2 = 5 V, VDD = 3.3 V, fS = 48 kHz, SCKI = 512 fS, 24-bit data, and Sampling Mode = Auto, unless otherwise noted. PCM1690 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 0.328 × fS Hz DIGITAL FILTER PERFORMANCE WITH SLOW ROLL-OFF Passband Stop band 0.673 × fS Passband ripple < 0.328 × fS Stop band attenuation > 0.673 × fS Hz ±0.0013 –75 dB dB DIGITAL FILTER PERFORMANCE Except SCKI = 128 fS and 192 fS 28/fS sec SCKI = 128 fS and 192 fS 19/fS sec Group delay time (quad) 19/fS sec De-emphasis error ±0.1 dB Group delay time (single, dual) ELECTRICAL CHARACTERISTICS: Power-Supply Requirements All specifications at TA = +25°C, VCC1 = VCC2 = 5 V, VDD = 3.3 V, fS = 48 kHz, SCKI = 512 fS, 24-bit data, and Sampling Mode = Auto, unless otherwise noted. PCM1690 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 4.5 5.0 5.5 VDC 3.0 POWER-SUPPLY REQUIREMENTS Voltage range VCC1/2 VDD ICC 3.3 3.6 VDC fS = 48 kHz 74 110 mA fS = 192 kHz 74 Full power-down Supply current (1) 57 fS = 192 kHz Full power-down 90 76 (1) 558 mA mA µA 60 fS = 48 kHz Power dissipation µA 170 fS = 48 kHz IDD mA 847 mW fS = 192 kHz 621 mW Full power-down (1) 1.05 mW TEMPERATURE RANGE Operating temperature Thermal resistance (1) PCM1690 Consumer grade θJA HTSSOP-48 –40 +85 +23 °C °C/W SCKI, BCK, and LRCK stopped. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 5 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com PIN CONFIGURATION DCA PACKAGE HTSSOP-48 (12 mm x 8 mm) (TOP VIEW) RSV2 1 48 RSV2 RSV1 2 47 VCC2 RSV2 3 46 AGND2 RSV1 4 45 RSV2 RSV2 5 44 VOUT1- LRCK 6 43 VOUT1+ BCK 7 42 VOUT2- DIN1 8 41 VOUT2+ DIN2 9 40 VOUT3- DIN3 10 39 VOUT3+ DIN4 11 38 VOUT4- VDD 12 PCM1690 Thermal Pad DGND 13 37 VOUT4+ 36 VOUT5- SCKI 14 35 VOUT5+ RST 15 34 VOUT6- ZERO1 16 33 VOUT6+ ZERO2 17 32 VOUT7- AMUTEI 18 31 VOUT7+ AMUTEO 19 30 VOUT8- MD/SDA/DEMP 20 29 VOUT8+ 28 RSV2 MC/SCL/FMT 21 27 AGND1 MS/ADR0/RSV 22 26 VCOM TEST/ADR1/RSV 23 25 VCC1 MODE 24 TERMINAL FUNCTIONS TERMINAL NAME PIN I/O PULLDOWN 5-V TOLERANT RSV2 1 — — — Reserved, tied to analog ground RSV1 2 — — — Reserved, left open RSV2 3 — — — Reserved, tied to analog ground RSV1 4 — — — Reserved, left open RSV2 5 — — — Reserved, tied to analog ground LRCK 6 I Yes No Audio data word clock input BCK 7 I Yes No Audio data bit clock input DIN1 8 I No No Audio data input for DAC1 and DAC2 DIN2 9 I No No Audio data input for DAC3 and DAC4 DIN3 10 I No No Audio data input for DAC5 and DAC6 DIN4 11 I No No Audio data input for DAC7 and DAC8 6 DESCRIPTION Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 TERMINAL FUNCTIONS (continued) TERMINAL NAME PIN I/O PULLDOWN 5-V TOLERANT VDD 12 — — — Digital power supply, +3.3 V DGND 13 — — — Digital ground SCKI 14 I No Yes System clock input RST 15 I Yes Yes Reset and power-down control input with active low ZERO1 16 O No No Zero detect flag output 1 ZERO2 17 O No No Zero detect flag output 2 AMUTEI 18 I No Yes Analog mute control input with active low AMUTEO 19 O No Yes Analog mute status output (1) with active low MD/SDA/DEMP 20 I/O No Yes Input data for SPI, data for I2C (1), de-emphasis control for hardware control mode MC/SCL/FMT 21 I No Yes Clock for SPI, clock for I2C, format select for hardware control mode MS/ADR0/RSV 22 I Yes Yes Chip Select for SPI, address select 0 for I2C, reserve (set low) for hardware control mode TEST/ADR1/RSV 23 I/O No Yes Test (factory use, left open) for SPI, address select 1 for I2C, reserve (set low) for hardware control mode MODE 24 I No No Control port mode selection. Tied to VDD: SPI, left open: H/W mode, tied to DGND: I2C VCC1 25 — — — Analog power supply 1, +5 V VCOM 26 — — — Voltage common decoupling AGND1 27 — — — Analog ground 1 RSV2 28 — — — Reserved, tied to analog ground VOUT8+ 29 O No No Positive analog output from DAC8 VOUT8- 30 O No No Negative analog output from DAC8 VOUT7+ 31 O No No Positive analog output from DAC7 VOUT7- 32 O No No Negative analog output from DAC7 VOUT6+ 33 O No No Positive analog output from DAC6 VOUT6- 34 O No No Negative analog output from DAC6 VOUT5+ 35 O No No Positive analog output from DAC5 VOUT5- 36 O No No Negative analog output from DAC5 VOUT4+ 37 O No No Positive analog output from DAC4 VOUT4- 38 O No No Negative analog output from DAC4 VOUT3+ 39 O No No Positive analog output from DAC3 VOUT3- 40 O No No Negative analog output from DAC3 VOUT2+ 41 O No No Positive analog output from DAC2 VOUT2- 42 O No No Negative analog output from DAC2 VOUT1+ 43 O No No Positive analog output from DAC1 VOUT1- 44 O No No Negative analog output from DAC1 RSV2 45 — — — Reserved, tied to analog ground AGND2 46 — — — Analog ground 2 VCC2 47 — — — Analog power supply 2, +5 V RSV2 48 — — — Reserved, tied to analog ground (1) DESCRIPTION Open-drain configuration in out mode. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 7 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com FUNCTIONAL BLOCK DIAGRAM DIN1 DIN2 DIN3 DIN4 BCK LRCK VOUT1+ DAC VOUT1- Audio Interface VOUT2+ DAC VOUT2VOUT3+ SCKI TEST/ADR1/RSV MS/ADR0/RSV MC/SCL/FMT MD/SDA/DEMP MODE ZERO1 ZERO2 AMUTEI AMUTEO RST VCC1 AGND1 VCC2 AGND2 VDD DGND VCOM 8 DAC SCK Manager VOUT3VOUT4+ DAC Control Interface VOUT4- Digital Filter and Volume 2 (SPI/I C/HW) VOUT5+ DAC VOUT5VOUT6+ DAC VOUT6VOUT7+ DAC VOUT7- Power Supply and Common Voltage VOUT8+ DAC VOUT8- Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 TYPICAL CHARACTERISTICS: Digital Filter All specifications at TA = +25°C, VCC1 = VCC2 = 5 V, VDD = 3.3 V, fS = 48 kHz, SCKI = 512 fS, 24-bit data, and Sampling Mode = Auto, unless otherwise noted. FREQUENCY RESPONSE (Single Rate) FREQUENCY RESPONSE PASSBAND (Single Rate) 0 0.010 Sharp Slow Sharp Slow 0.008 0.006 -40 Amplitude (dB) Amplitude (dB) -20 -60 -80 0.004 0.002 0 -0.002 -0.004 -100 -0.006 -120 -0.008 -140 0 1 2 -0.010 4 3 0 0.1 Normalized Frequency (fS) 0.5 0.4 Figure 2. FREQUENCY RESPONSE (Dual Rate) FREQUENCY RESPONSE PASSBAND (Dual Rate) 0.010 Sharp Slow -20 Sharp Slow 0.008 0.006 -40 Amplitude (dB) Amplitude (dB) 0.3 Figure 1. 0 -60 -80 0.004 0.002 0 -0.002 -0.004 -100 -0.006 -120 -0.008 -140 0 1 2 -0.010 4 3 0 0.1 Normalized Frequency (fS) 0.2 0.3 0.5 0.4 Normalized Frequency (fS) Figure 3. Figure 4. FREQUENCY RESPONSE (Quad Rate) FREQUENCY RESPONSE PASSBAND (Quad Rate) 0 0.010 Sharp Slow -20 Sharp Slow 0.008 0.006 -40 Amplitude (dB) Amplitude (dB) 0.2 Normalized Frequency (fS) -60 -80 0.004 0.002 0 -0.002 -0.004 -100 -0.006 -120 -0.008 -140 0 0.5 1.0 1.5 2.0 -0.010 0 Normalized Frequency (fS) 0.1 0.2 0.3 0.4 0.5 Normalized Frequency (fS) Figure 5. Figure 6. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 9 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com TYPICAL CHARACTERISTICS: Digital De-Emphasis Filter All specifications at TA = +25°C, VCC1 = VCC2 = 5 V, VDD = 3.3 V, fS = 48 kHz, SCKI = 512 fS, 24-bit data, and Sampling Mode = Auto, unless otherwise noted. DE-EMPHASIS CHARACTERISTIC (fS = 44.1 kHz) 0 0 -1 -1 -2 -2 -3 -3 Amplitude (dB) Amplitude (dB) DE-EMPHASIS CHARACTERISTIC (fS = 48 kHz) -4 -5 -6 -4 -5 -6 -7 -7 -8 -8 -9 -9 -10 -10 0 4 2 6 8 10 12 14 16 18 20 22 0 2 4 6 8 10 12 Frequency (kHz) Frequency (kHz) Figure 7. Figure 8. DE-EMPHASIS CHARACTERISTIC (fS = 32 kHz) 14 16 18 20 ANALOG FILTER CHARACTERISTIC 0 0 -1 -10 -3 Amplitude (dB) Amplitude (dB) -2 -4 -5 -6 -20 -30 -7 -8 -40 -9 -10 0 10 2 4 6 8 10 -50 12 14 1k 10k 100k Frequency (kHz) Frequency (Hz) Figure 9. Figure 10. Submit Documentation Feedback 1M 10M Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 TYPICAL CHARACTERISTICS: Dynamic Performance All specifications at TA = +25°C, VCC1 = VCC2 = 5 V, VDD = 3.3 V, fS = 48 kHz, SCKI = 512 fS, 24-bit data, and Sampling Mode = Auto, unless otherwise noted. DYNAMIC RANGE AND SNR vs TEMPERATURE THD+N vs TEMPERATURE 118 Dynamic Range and SNR (dB) -90 THD+N (dB) -92 -94 -96 -98 -100 Dynamic Range 114 SNR 112 110 108 106 -102 -40 -15 35 10 60 85 -40 60 Temperature (°C) Figure 11. Figure 12. THD+N vs SUPPLY VOLTAGE DYNAMIC RANGE AND SNR vs SUPPLY VOLTAGE 85 Dynamic Range and SNR (dB) 118 -92 -94 -96 -98 -100 -102 4.50 35 10 -15 Temperature (°C) -90 THD+N (dB) 116 4.75 5.00 5.25 5.50 116 Dynamic Range 114 SNR 112 110 108 106 4.50 4.75 5.00 Supply Voltage (V) Supply Voltage (V) Figure 13. Figure 14. 5.25 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 5.50 11 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com TYPICAL CHARACTERISTICS: Output Spectrum All specifications at TA = +25°C, VCC1 = VCC2 = 5 V, VDD = 3.3 V, fS = 48 kHz, SCKI = 512 fS, 24-bit data, and Sampling Mode = Auto, unless otherwise noted. OUTPUT SPECTRUM (–60 dB, N = 32768) 0 0 -20 -20 -40 -40 Amplitude (dB) Amplitude (dB) OUTPUT SPECTRUM (0 dB, N = 32768) -60 -80 -100 -60 -80 -100 -120 -120 -140 -140 -160 -160 0 5 20 15 10 0 5 10 Frequency (kHz) 15 20 Frequency (kHz) Figure 15. Figure 16. OUTPUT SPECTRUM (BPZ, N = 32768) 0 -20 Amplitude (dB) -40 -60 -80 -100 -120 -140 -160 0 5 10 15 20 Frequency (kHz) Figure 17. 12 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 PRODUCT OVERVIEW The PCM1690 is a high-performance, multi-channel DAC targeted for consumer audio applications such as Blu-ray DVD players and HD DVD players, as well as home multi-channel audio applications (such as home theaters and A/V receivers). The PCM1690 consists of an eight-channel DAC. The DAC output type is fixed with a differential configuration. The PCM1690 supports 16-/20-/24-/32-bit linear PCM input data in I2S- and left-justified audio formats, and 24-bit linear PCM input data in right-justified, DSP, and TDM formats for various sampling frequencies from 8 kHz to 192 kHz. The TDM format is useful for saving bus line interface numbers for multi-channel audio data communication between the DAC and a digital audio processor. The PCM1690 offers three modes for device control: two-wire I2C software, three-wire SPI software, and hardware modes. ANALOG OUTPUTS The PCM1690 includes eight DACs, each with individual pairs of differential voltage outputs pins. The full-scale output voltage is (1.6 × VCC1) VPP at the differential output mode. A dc-coupled load is allowed in addition to an ac-coupled load if the load resistance conforms to the specification. These balanced outputs are each capable of driving 0.8 VCC1 (4 VPP) typical into a 5-kΩ, ac-coupled or 15-kΩ, dc-coupled load with VCC1 = +5 V. The internal output amplifiers for VOUT1 through VOUT8 are biased to the dc common voltage, equal to (0.5 × VCC1). The output amplifiers include an RC continuous-time filter that helps to reduce the out-of-band noise energy present at the DAC outputs as a result of the noise shaping characteristics of the PCM1690 delta-sigma (ΔΣ) DACs. The frequency response of this filter is shown in the Analog Filter Characteristic (Figure 10) of the Typical Characteristics. By itself, this filter is not enough to attenuate the out-of-band noise to an acceptable level for most applications. An external low-pass filter is required to provide sufficient out-of-band noise rejection. Further discussion of DAC post-filter circuits is provided in the Application Information section. Table 1. Pin Assignments in Differential Output Mode DIGITAL INPUT DIN1 DIN2 DIN3 DIN4 CHANNEL DIFFERENTIAL OUTPUT 1 (DAC1) VOUT1+, VOUT1– 2 (DAC2) VOUT2+, VOUT2– 3 (DAC3) VOUT3+, VOUT3– 4 (DAC4) VOUT4+, VOUT4– 5 (DAC5) VOUT5+, VOUT5– 6 (DAC6) VOUT6+, VOUT6– 7 (DAC7) VOUT7+, VOUT7– 8 (DAC8) VOUT8+, VOUT8– VOLTAGE REFERENCE VCOM The PCM1690 includes a pin for the common-mode voltage output, VCOM. This pin should be connected to the analog ground via a decoupling capacitor. This pin can also be used to bias external high-impedance circuits, if they are required. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 13 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com SYSTEM CLOCK INPUT The PCM1690 requires an external system clock input applied at the SCKI input for DAC operation. The system clock operates at an integer multiple of the sampling frequency, or fS. The multiples supported in DAC operation include 128 fS, 192 fS, 256 fS, 384 fS, 512 fS, 768 fS, and 1152 fS. Details for these system clock multiples are shown in Table 2. Figure 18 and Table 3 show the SCKI timing requirements. Table 2. System Clock Frequencies for Common Audio Sampling Rates DEFAULT SAMPLING MODE SAMPLING FREQUENCY SYSTEM CLOCK FREQUENCY (MHz) fS (kHz) 128 fS 192 fS 256 fS 384 fS 512 fS 768 fS 1152 fS 8 N/A N/A 2.0480 3.0720 4.0960 6.1440 9.2160 16 2.0480 3.0720 4.0960 6.1440 8.1920 12.2880 18.4320 32 4.0960 6.1440 8.1920 12.2880 16.3840 24.5760 36.8640 44.1 5.6448 8.4672 11.2896 16.9344 22.5792 33.8688 N/A Single rate Dual rate Quad rate 48 6.1440 9.2160 12.2880 18.4320 24.5760 36.8640 N/A 88.2 11.2896 16.9344 22.5792 33.8688 N/A N/A N/A 96 12.2880 18.4320 24.5760 36.8640 N/A N/A N/A 176.4 22.5792 33.8688 N/A N/A N/A N/A N/A 192 24.5760 36.8640 N/A N/A N/A N/A N/A tSCH High 2.0 V System Clock (SCKI) 0.8 V Low tSCY tSCL Figure 18. System Clock Timing Requirements Table 3. Timing Requirements for Figure 18 14 SYMBOL PARAMETER MIN tSCY System clock cycle time 27 ns tSCH System clock width high 10 ns tSCL System clock width low 10 ns — System clock duty cycle 40 Submit Documentation Feedback MAX 60 UNIT % Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 SAMPLING MODE The PCM1690 supports three sampling modes (single rate, dual rate, and quad rate) in DAC operation. In single rate mode, the DAC operates at an oversampling frequency of x128 (except when SCKI = 128 fS and 192 fS). This mode is supported for sampling frequencies less than 50 kHz. In dual rate mode, the DAC operates at an oversampling frequency of x64; this mode is supported for sampling frequencies less than 100 kHz. In quad rate mode, the DAC operates at an oversampling frequency of x32. The sampling mode is automatically selected according to the ratio of system clock frequency and sampling frequency by default (that is, single rate for 512 fS, 768 fS, and 1152 fS; dual rate for 256 fS and 384 fS; and quad rate for 128 fS and 192 fS), but manual selection is also possible for specified combinations through the serial mode control register. Table 4 and Figure 19 show the relation among the oversampling rate (OSR) of the digital filter and ΔΣ modulator, the noise-free shaped bandwidth, and each sampling mode setting. Table 4. DAC Filter OSR, Modulator OSR, and Noise-Free Shaped Bandwidth for Each Sampling Mode SAMPLING MODE REGISTER SETTING Auto Single Dual Quad (1) (2) NOISE-FREE SHAPED BANDWIDTH (kHz) (1) SYSTEM CLOCK FREQUENCY (xfS) fS = 48 kHz fS = 96 kHz fS = 192 kHz DIGITAL FILTER OSR MODULATOR OSR 512, 768, 1152 40 N/A N/A ×8 x128 256, 384 20 40 N/A x8 x64 128, 192 (2) 10 20 40 x4 x32 512, 768, 1152 40 N/A N/A x8 x128 256, 384 40 N/A N/A x8 x128 128, 192 (2) 20 N/A N/A x4 x64 256, 384 20 40 N/A x8 x64 (2) 20 40 N/A x4 x64 128, 192 (2) 10 20 40 x4 x32 128, 192 Bandwidth in which noise is shaped out. Quad mode filter characteristic is applied. 0 DSM_Single DSM_Dual DSM_Quad -20 Amplitude (dB) -40 DF_Single DF_Dual DF_Quad -60 -80 -100 -120 -140 -160 -180 -200 0 0.5 1.0 1.5 2.0 Normalized Frequency (fS) Figure 19. ΔΣ Modulator and Digital Filter Characteristic Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 15 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com RESET OPERATION The PCM1690 has both an internal power-on reset circuit and an external reset circuit. The sequences for both reset circuits are illustrated in Figure 20 and Figure 21. Figure 20 describes the timing at the internal power-on reset. Initialization is triggered automatically at the point where VDD exceeds 2.2 V typical, and the internal reset is released after 3846 SCKI clock cycles from power-on if RST is held high and SCKI is provided. VOUT from the DACs are forced to the VCOM level initially (that is, 0.5 × VCC1) and settle at a specified level according to the rising VCC. If synchronization among SCKI, BCK, and LRCK is maintained, VOUT provides an output that corresponds to DIN after 3846 SCKI clocks from power-on. If the synchronization is not held, the internal reset is not released, and both operating modes are maintained at reset and power-down states; after synchronization forms again, the DAC returns to normal operation with the previous sequences. Figure 21 illustrates a timing diagram at the external reset. RST accepts an externally-forced reset with RST low, and provides a device reset and power-down state that achieves the lowest power dissipation state available in the PCM1690. If RST goes from high to low under synchronization among SCKI, BCK, and LRCK, the internal reset is asserted, all registers and memory are reset, and finally the PCM1690 enters into all power-down states. At the same time, VOUT is immediately forced into the AGND1 level. To begin normal operation again, toggle RST high; the same power-up sequence is performed as the power-on reset shown in Figure 20. The PCM1690 does not require particular power-on sequences for VCC and VDD; it allows VDD on and then VCC on, or VCC on and then VDD on. From the viewpoint of the Absolute Maximum Ratings, however, simultaneous power-on is recommended for avoiding unexpected responses on VOUTx. Figure 20 illustrates the response for VCC on with VDD on. (VDD = 3.3 V, typ) VDD 0V (VDD = 2.2 V, typ) SCKI, BCK, LRCK RST Synchronous Clocks 3846 ´ SCKI Normal Operation Internal Reset VOUT1± to VOUT8± 0.5 ´ VCC VCOM (0.5 ´ VCC1) Figure 20. Power-On-Reset Timing Requirements (VDD = 3.3 V, typ) VDD SCKI, BCK, LRCK 0V Synchronous Clocks Synchronous Clocks 100 ns (min) RST 3846 ´ SCKI Internal Reset Normal Operation Power-Down Normal Operation VOUT1± to VOUT8± 0.5 ´ VCC Figure 21. External Reset Timing Requirements 16 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 AUDIO SERIAL PORT OPERATION The PCM1690 audio serial port consists of six signals: BCK, LRCK, DIN1, DIN2, DIN3, and DIN4. BCK is a bit clock input. LRCK is a left/right word clock input or frame synchronization clock input. DIN1/2/3/4 are the audio data inputs for VOUT1–8. AUDIO DATA INTERFACE FORMATS AND TIMING The PCM1690 supports 10 audio data interface formats: 16-/20-/24-/32-bit I2S, 16-/20-/24-/32-bit left-justified, 24-bit right-justified, 16-bit right-justified, 24-bit left-justified mode DSP, 24-bit I2S mode DSP, 24-bit left-justified mode TDM, 24-bit I2S mode TDM, 24-bit left-justified mode high-speed TDM, and 24-bit I2S mode high-speed TDM. In the case of I2S, left-justified, and right-justified data formats, 64 BCKs, 48 BCKs, and 32 BCKs per LRCK period are supported; but 48 BCKs are limited in 192/384/768 fS SCKI, and 32 BCKs are limited in 16-bit right-justified only. In the case of TDM data format in single rate, BCK, LRCK, and DIN1 are used. In the case of TDM data format in dual rate, BCK, LRCK, and DIN1/2 are used. In the case of high-speed TDM format in dual rate, BCK, LRCK, and DIN1 are used. In the case of high-speed TDM format in quad rate, BCK, LRCK, and DIN1/2 are used. TDM format and high-speed TDM format are supported only at SCKI = 512 fS, 256 fS, 128 fS, and fBCK ≤ fSCKI. The audio data formats are selected by MC/SCL/FMT in hardware control mode and by control register settings in software control mode. All data must be in binary twos complement and MSB first. Table 5 summarizes the applicable formats and describes the relationships among them and the respective restrictions with mode control. Figure 22 through Figure 28 show 10 audio interface data formats. Table 5. Audio Data Interface Formats and Sampling Rate, Bit Clock, and System Clock Restrictions CONTROL MODE FORMAT DATA BITS MAX LRCK FREQUENCY (fS) SCKI RATE (xfS) BCK RATE (xfS) APPLICABLE PINS I2S/Left-Justified 16/20/24/32 (1) 192 kHz 128 to 1152 (2) 64, 48 DIN1/2/3/4 Right-Justified 24, 16 192 kHz 128 to 1152 (2) 64, 48, 32 (16 bit) (3) DIN1/2/3/4 I S/Left-Justified DSP 24 192 kHz 128 to 768 64 DIN1/2/3/4 24 48 kHz 256, 512 256 DIN1 24 96 kHz 128, 256 128 DIN1/2 2 Software control I2S/ Left-Justified TDM High-Speed I2S/Left-Justified TDM 24 96 kHz 256 256 DIN1 24 192 kHz 128 128 DIN1/2 I2S 16/20/24/32 (1) 192 kHz 128 to 1152 (2) 64, 48 DIN1/2/3/4 24 48 kHz 512 256 DIN1 24 96 kHz 256 128 DIN1/2 Hardware control (1) (2) (3) I2S TDM 32-bit data length is acceptable only for BCK = 64 fS and when using I2S and Left-Justified format. 1152 fS is acceptable only for fS = 32 kHz, BCK = 64 fS, and when using I2S, Left-Justified, and 24-bit Right-Justified format. BCK = 32 fS is supported only for 16-bit data length. Ch 1 (DIN1) or Ch 3 (DIN2) Ch 5 (DIN3) or Ch 7 (DIN4) LRCK Ch 2 (DIN1) or Ch 4 (DIN2) Ch 6 (DIN3) or Ch 8 (DIN4) BCK DIN1/2/3/4 N M L 2 1 0 LSB MSB N M L 2 MSB 1 0 LSB Figure 22. Audio Data Format: 16-/20-/24-/32-Bit I2S (N = 15/19/23/31, M = 14/18/22/30, and L = 13/17/21/29) Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 17 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com LRCK Ch 2 (DIN1) or Ch 4 (DIN2) Ch 6 (DIN3) or Ch 8 (DIN4) Ch 1 (DIN1) or Ch 3 (DIN2) Ch 5 (DIN3) or Ch 7 (DIN4) BCK DIN1/2/3/4 N M L 2 N M L 1 0 LSB MSB 1 0 2 N LSB MSB Figure 23. Audio Data Format: 16-/20-/24-/32-Bit Left-Justified (N = 15/19/23/31, M = 14/18/22/30, and L = 13/17/21/29) Ch 2 (DIN1) or Ch 4 (DIN2) Ch 6 (DIN3) or Ch 8 (DIN4) Ch 1 (DIN1) or Ch 3 (DIN2) Ch 5 (DIN3) or Ch 7 (DIN4) LRCK BCK DIN1/2/3/4 0 23 22 21 2 MSB 1 0 23 22 21 LSB 2 MSB 1 0 LSB Figure 24. Audio Data Format: 24-Bit Right-Justified LRCK Ch 2 (DIN1) or Ch 4 (DIN2) Ch 6 (DIN3) or Ch 8 (DIN4) Ch 1 (DIN1) or Ch 3 (DIN2) Ch 5 (DIN3) or Ch 7 (DIN4) BCK DIN1/2/3/4 15 14 13 0 2 MSB 1 0 15 14 13 LSB 2 MSB 1 0 LSB Figure 25. Audio Data Format: 16-Bit Right-Justified 1/fS (64 BCKs) Ch 1 (DIN1) or Ch 3 (DIN2) Ch 5 (DIN3) or Ch 7 (DIN4) LRCK Ch 2 (DIN1) or Ch 4 (DIN2) Ch 6 (DIN3) or Ch 8 (DIN4) BCK Left-Justified Mode DIN1/2/3/4 23 22 21 2 1 0 2 1 23 22 21 2 1 0 2 1 23 22 21 2 I S Mode DIN1/2/3/4 23 22 21 0 23 22 21 0 23 22 Figure 26. Audio Data Format: 24-Bit DSP Format 18 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 1/fS (256 BCKs at Single Rate, 128 BCKs at Dual Rate) LRCK BCK Left-Justified Mode DIN1 (Single) 2 I S Mode DIN1 (Single) Left-Justified Mode DIN1/2 (Dual) 23 22 23 22 23 22 0 23 22 Ch 2 32 BCKs 0 23 22 23 22 0 1 0 23 22 0 23 22 Ch 3 32 BCKs 23 22 0 23 22 Ch 4 32 BCKs 0 23 22 Ch 1/Ch 5 32 BCKs 2 I S Mode DIN1/2 (Dual) 0 Ch 1 32 BCKs 23 22 0 1 0 23 22 23 22 23 22 0 23 22 Ch 6 32 BCKs 0 23 22 Ch 2/Ch 6 32 BCKs 1 0 0 Ch 5 32 BCKs 23 22 0 23 22 Ch 7 32 BCKs 0 1 0 23 22 0 23 22 23 22 23 22 23 22 0 1 0 Ch 3/Ch 7 32 BCKs 1 0 0 Ch 8 32 BCKs 23 22 23 22 Ch 4/Ch 8 32 BCKs 1 0 23 22 1 0 23 22 Figure 27. Audio Data Format: 24-Bit TDM Format (SCKI = 128 fS, 256 fS, and 512 fS Only) 1/fS (256 BCKs at Dual Rate, 128 BCKs at Quad Rate) LRCK BCK Left-Justified Mode DIN1 (Dual) 2 I S Mode DIN1 (Dual) Left-Justified Mode DIN1/2 (Quad) 23 22 23 22 Ch 1 32 BCKs 23 22 23 22 0 23 22 Ch 2 32 BCKs 0 23 22 1 0 23 22 1 0 0 23 22 Ch 3 32 BCKs 0 23 22 23 22 Ch 1/Ch 5 32 BCKs 2 I S Mode DIN1/2 (Quad) 0 0 23 22 Ch 4 32 BCKs 0 23 22 1 0 1 0 23 22 Ch 5 32 BCKs 0 23 22 0 23 22 Ch 6 32 BCKs 0 23 22 Ch 2/Ch 6 32 BCKs 23 22 0 23 22 1 0 1 0 23 22 Ch 7 32 BCKs 0 23 22 0 23 22 Ch 8 32 BCKs 0 23 22 Ch 3/Ch 7 32 BCKs 23 22 0 23 22 1 0 0 23 22 23 22 Ch 4/Ch 8 32 BCKs 23 22 1 0 23 22 Figure 28. Audio Data Format: 24-Bit High-Speed TDM Format (SCKI = 128 fS and 256 fS Only) Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 19 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com AUDIO INTERFACE TIMING Figure 29 and Figure 30 describe the detailed interface timing specifications. tBCH tBCL BCK (Input) 1.4 V tBCY tLRH tLRS LRCK (Input) 1.4 V tDIS tDIH DIN1/2/3/4 1.4 V Figure 29. Audio Interface Timing Requirements for Left-Justified, Right-Justified, and I2S Data Formats Table 6. Timing Requirements for Figure 29 SYMBOL DESCRIPTION MIN TYP MAX UNIT tBCY BCK cycle time 75 ns tBCH BCK pulse width high 35 ns tBCL BCK pulse width low 35 ns tLRS LRCK setup time to BCK rising edge 10 ns tLRH LRCK hold time to BCK rising edge 10 ns tDIS DIN1/2/3/4 setup time to BCK rising edge 10 ns tDIH DIN1/2/3/4 hold time to BCK rising edge 10 ns tBCL tBCH BCK (Input) 1.4 V tBCY tLRH tLRS LRCK (Input) 1.4 V tDIS tLRW tDIH DIN1/2/3/4 1.4 V Figure 30. Audio Interface Timing Requirements for DSP and TDM Data Formats Table 7. Timing Requirements for Figure 30 SYMBOL MIN TYP MAX UNIT BCK cycle time 40 ns tBCH BCK pulse width high 15 ns tBCL BCK pulse width low tLRW 20 DESCRIPTION tBCY 15 ns LRCK pulse width high (DSP format) tBCY tBCY 1/fS – tBCY LRCK pulse width high (TDM format) tBCY tLRS LRCK setup time to BCK rising edge 10 ns tLRH LRCK hold time to BCK rising edge 10 ns tDIS DIN1/2/3/4 setup time to BCK rising edge 10 ns tDIH DIN1/2/3/4 hold time to BCK rising edge 10 ns Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 SYNCHRONIZATION WITH THE DIGITAL AUDIO SYSTEM The PCM1690 operates under the system clock (SCKI) and the audio sampling rate (LRCK). Therefore, SCKI and LRCK must have a specific relationship. The PCM1690 does not need a specific phase relationship between the audio interface clocks (LRCK, BCK) and the system clock (SCKI), but does require a specific frequency relationship (ratiometric) between LRCK, BCK, and SCKI. If the relationship between SCKI and LRCK changes more than ±2 BCK clocks because of jitter, sampling frequency change, etc., the DAC internal operation stops within 1/fS, and the analog output is forced into VCOM (0.5 VCC1) until re-synchronization between SCKI, LRCK, and BCK completes and then 38/fS (single, dual rate) or 29/fS (quad rate) passes. In the event the change is less than ±2 BCKs, re-synchronization does not occur, and this analog output control and discontinuity does not occur. Figure 31 shows the DAC analog output during loss of synchronization. During undefined data periods, some noise may be generated in the audio signal. Also, the transition of normal to undefined data and undefined (or zero) data to normal data creates a discontinuity of data on the analog outputs, which then may generate some noise in the audio signal. DAC outputs (VOUTx) hold the previous state if the system clock halts, but the asynchronous and re-synchronization processes will occur after the system clock resumes. State of Synchronization Asynchronous Synchronous Within 1/fS Undefined Data DAC VOUTX± VCOM (0.5 VCC1) Synchronous 38/fS (single, dual rate) 29/fS (quad rate) Normal Normal Figure 31. DAC Outputs During Loss of Synchronization ZERO FLAG The PCM1690 has two ZERO flag pins (ZERO1 and ZERO2) that can be assigned to the combinations shown in Table 8. Zero flag combinations are selected through control register settings. If the input data of the left and right channel of all assigned channels remain at '0' for 1024 sampling periods (LRCK clock periods), the ZERO1/2 bits are set to a high level, logic '1' state. Furthermore, if the input data of any channels of assigned channels read '1', the ZERO1/2 are set to a low level, logic '0' state, immediately. Zero data detection is supported for 16-/20-/24-bit data width, but is not supported for 32-bit data width. The active polarity of the zero flag output can be inverted through control register settings. The reset default is active high for zero detection. In parallel hardware control mode, ZERO1 and ZERO2 are fixed with combination A shown in Table 8. Table 8. Zero Flag Outputs Combination ZERO FLAG COMBINATION ZERO1 ZERO2 A DATA1, left channel DATA1, right channel B DATA1–4 DATA1–4 C DATA4 DATA1–3 D DATA1 DATA2–4 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 21 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com AMUTE CONTROL The PCM1690 has an AMUTE control input, status output pins, and functionality. AMUTEI is the input control pin of the internal analog mute circuit. An AMUTEI low input causes the DAC output to cut-off from the digital input and forces it to the center level (0.5 VCC1). AMUTEO is the status output pin of the internal analog mute circuit. AMUTEO low indicates the analog mute control circuit is active because of a programmed condition (such as an SCKI halt, asynchronous detect, zero detect, or issue with the DAC disable command) that forces the DAC outputs to a center level. Because AMUTEI is not terminated internally and AMUTEO is an open-drain output, pull-ups by the appropriate resistors are required for proper operation. Additionally, because the AMUTEI pin control and power-down control in register (OPEDA when high, PSMDA when low) do not function together, AMUTEI takes priority over power-down control. Therefore, power-down control is ignored during AMUTEI low, and AMUTEI low forces the DAC output to a center level (0.5 VCC1) even if the power-down control is asserted. MODE CONTROL The PCM1690 includes three mode control interfaces with two oversampling configurations, depending on the input state of the MODE pin, as shown in Table 9. The pull-up and pull-down resistors must each be less than 10 kΩ. Table 9. Mode Control Selection MODE MODE CONTROL INTERFACE Two-wire (I2C) serial control, selectable oversampling configuration Tied to DGND, low Left open Two-wire parallel control, auto mode oversampling configuration Tied to VDD, high Three-wire (SPI) serial control, selectable oversampling configuration The input state of the MODE pin is sampled at the moment of power-on, or during a low-to-high transition of the RST pin, with the system clock input. Therefore, input changes after reset are ignored until the next power-on or reset. From the mode control selection described in Table 9, the functions of four pins are changed, as shown in Table 10. Table 10. Pin Functions for Interface Mode PIN ASSIGNMENTS PIN SPI I2C H/W 20 MD (input) SDA (input/output) DEMP (input) 21 MC (input) SCL (input) FMT (input) 22 MS (input) ADR0 (input) RSV (input, low) 23 Test (output, open) ADR1 (input) RSV (input, low) In serial mode control, the actual mode control is performed by register writes (and reads) through the SPI- or I2C-compatible serial control port. In parallel mode control, two specific functions are controlled directly through the high/low control of two specific pins, as described in the following section. PARALLEL HARDWARE CONTROL The functions shown in Table 11 and Table 12 are controlled by two pins, DEMP and FMT, in parallel hardware control mode. The DEMP pin controls the 44.1-kHz digital de-emphasis function of all eight channels. The FMT pin controls the audio interface format for all eight channels. Table 11. DEMP Functionality DEMP 22 DESCRIPTION Low De-emphasis off High 44.1 kHz de-emphasis on Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 Table 12. FMT Functionality FMT DESCRIPTION Low 16-/20-/24-/32-bit I2S format High 24-bit I2S mode TDM format THREE-WIRE (SPI) SERIAL CONTROL The PCM1690 includes an SPI-compatible serial port that operates asynchronously with the audio serial interface. The control interface consists of MD/SDA/DEMP, MC/SCL/FMT, and MS/ADR0/RSV. MD is the serial data input to program the mode control registers. MC is the serial bit clock that shifts the data into the control port. MS is the select input to enable the mode control port. CONTROL DATA WORD FORMAT All single write operations via the serial control port use 16-bit data words. Figure 32 shows the control data word format. The first bit (fixed at '0') is for write controls; after the first bit are seven other bits, labeled ADR[6:0] that set the register address for the write operation. The eight least significant bits (LSBs), D[7:0] on MD, contain the data to be written to the register specified by ADR[6:0]. MSB 0 LSB ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 ADR0 D6 D7 D5 D3 D4 Register Address D2 D1 D0 Register Data Figure 32. Control Data Word Format for MD REGISTER WRITE OPERATION Figure 33 shows the functional timing diagram for single write operations on the serial control port. MS is held at a high state until a register is to be written. To start the register write cycle, MS is set to a low state. 16 clocks are then provided on MC, corresponding to the 16 bits of the control data word on MD. After the 16th clock cycle has been completed, MS is set high to latch the data into the indexed mode control register. Also, the PCM1690 supports multiple write operations in addition to single write operations, which can be performed by sending the following N-times of the 8-bit register data after the first 16-bit register address and register data while keeping the MC clocks and MS at a low state. Closing a multiple write operation can be accomplished by setting MS to a high state. MS MC MD (1) X '0' ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 ADR0 D7 D6 D5 D4 D3 D2 D1 D0 X X 0 ADR6 (1) X = don't care. Figure 33. Register Write Operation Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 23 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com TIMING REQUIREMENTS Figure 34 shows a detailed timing diagram for the three-wire serial control interface. These timing parameters are critical for proper control port operation. tMHH MS 1.4 V tMCH tMSS tMCL tMSH MC 1.4 V tMCY tMDS ADR0 MSB (R/W) MD tMDH LSB (D0) D7 1.4 V Figure 34. Three-Wire Serial Control Interface Timing Table 13. Timing Requirements for Figure 34 SYMBOL PARAMETER MIN MAX UNIT tMCY MC pulse cycle time 100 ns tMCL MC low-level time 40 ns tMCH MC high-level time 40 ns tMHH MS high-level time tMCY ns tMSS MS falling edge to MC rising edge 30 ns tMSH MS rising edge from MC rising edge for LSB 15 ns tMDH MD hold time 15 ns tMDS MD setup time 15 ns TWO-WIRE (I2C) SERIAL CONTROL The PCM1690 supports an I2C-compatible serial bus and data transmission protocol for fast mode configured as a slave device. This protocol is explained in the I2C specification 2.0. The PCM1690 has a 7-bit slave address, as shown in Figure 35. The first five bits are the most significant bits (MSB) of the slave address and are factory-preset to '10011'. The next two bits of the address byte are selectable bits that can be set by MS/ADR0/RSV and TEST/ADR1/RSV. A maximum of four PCM1690s can be connected on the same bus at any one time. Each PCM1690 responds when it receives its own slave address. MSB 1 LSB 0 0 1 1 ADR1 ADR0 R/W Figure 35. Slave Address 24 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 PACKET PROTOCOL A master device must control the packet protocol, which consists of a start condition, slave address with the read/write bit, data if a write operation is required, acknowledgment if a read operation is required, and stop condition. The PCM1690 supports both slave receiver and transmitter functions. Details about DATA for both write and read operations are described in Figure 36. SDA SCL 1 to 7 St Slave Address 8 9 (1) R/W ACK 1 to 8 (2) (3) DATA 9 1 to 8 9 9 ACK DATA ACK ACK Sp Start Condition Stop Condition (1) R/W: Read operation if '1'; write operation otherwise. (2) ACK: Acknowledgment of a byte if '0', not Acknowledgment of a byte if '1'. (3) DATA: Eight bits (byte); details are described in the Write Operation and Read Operation sections. Figure 36. I2C Packet Control Protocol WRITE OPERATION The PCM1690 supports a receiver function. A master device can write to any PCM1690 register using single or multiple accesses. The master sends a PCM1690 slave address with a write bit, a register address, and the data. If multiple access is required, the address is that of the starting register, followed by the data to be transferred. When valid data are received, the index register automatically increments by one. When the register address reaches &h4F, the next value is &h40. When undefined registers are accessed, the PCM1690 does not send an acknowledgment. Figure 37 illustrates a diagram of the write operation. The register address and write data are in 8-bit, MSB-first format. Transmitter M M M S M S M S M S S M Data Type St Slave Address W ACK Reg Address ACK Write Data 1 ACK Write Data 2 ACK ACK Sp NOTE: M = Master device, S = Slave device, St = Start condition, W = Write, ACK = Acknowledge, and Sp = Stop condition. Figure 37. Framework for Write Operation READ OPERATION A master device can read the registers of the PCM1690. The value of the register address is stored in an indirect index register in advance. The master sends the PCM1690 slave address with a read bit after storing the register address. Then the PCM1690 transfers the data that the index register points to. Figure 38 shows a diagram of the read operation. Transmitter Data Type M St M Slave Address M W S M ACK Reg Address S ACK M Sr M Slave Address M R S S ACK Read Data M M NACK Sp NOTE: M = Master device, S = Slave device, St = Start condition, Sr = Repeated start condition, W = Write, R = Read, ACK = Acknowledge, NACK = Not acknowledge, and Sp = Stop condition. NOTE: The slave address after the repeated start condition must be the same as the previous slave address. Figure 38. Framework for Read Operation Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 25 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com TIMING REQUIREMENTS: SCL AND SDA A detailed timing diagram for SCL and SDA is shown in Figure 39. Repeated START START tBUF STOP tD-HD tD-SU tSDA-R tP-SU SDA tSCL-R tSDA-F tS-HD tLOW SCL tSCL-F tS-HD tHI tS-SU Figure 39. SCL and SDA Control Interface Timing Table 14. Timing Requirements for Figure 39 STANDARD MODE SYMBOL PARAMETER MIN MAX FAST MODE MIN 100 MAX UNIT 400 kHz fSCL SCL clock frequency tBUF Bus free time between STOP and START condition 4.7 1.3 µs tLOW Low period of the SCL clock 4.7 1.3 µs tHI High period of the SCL clock 4.0 0.6 µs tS-SU Setup time for START/Repeated START condition 4.7 0.6 µs tS-HD Hold time for START/Repeated START condition 4.0 0.6 µs tD-SU Data setup time 250 100 tD-HD Data hold time 0 tSCL-R ns 3450 0 900 ns Rise time of SCL signal 1000 20 + 0.1 CB 300 ns tSCL-F Fall time of SCL signal 1000 20 + 0.1 CB 300 ns tSDA-R Rise time of SDA signal 1000 20 + 0.1 CB 300 ns tSDA-F Fall time of SDA signal 1000 20 + 0.1 CB 300 tP-SU Setup time for STOP condition tGW Allowable glitch width N/A 50 CB Capacitive load for SDA and SCL line 400 100 VNH Noise margin at high level for each connected device (including hysteresis) 0.2 × VDD 0.2 × VDD V VNL Noise margin at low level for each connected device (including hysteresis) 0.1 × VDD 0.1 × VDD V VHYS Hysteresis of Schmitt trigger input N/A 0.05 × VDD V 26 4.0 Submit Documentation Feedback ns µs 0.6 pF Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 CONTROL REGISTER DEFINITIONS (SOFTWARE MODE ONLY) The PCM1690 has many user-programmable functions that are accessed via control registers, and are programmed through the SPI or I2C serial control port. Table 15 shows the available mode control functions along with reset default conditions and associated register address. Table 16 lists the register map. Table 15. User-Programmable Mode Control Functions FUNCTION RESET DEFAULT REGISTER LABEL Mode control register reset Normal operation 64 MRST System reset Normal operation 64 SRST Mute disabled 64 AMUTE[3:0] Auto 64 SRDA[1:0] Power save 65 PSMDA I2S 65 FMTDA[3:0] Normal operation 66 OPEDA[3:0] Sharp roll-off 66 FLT[3:0] Normal 67 REVDA[8:1] Mute disabled 68 MUTDA[8:1] ZERO[8:1] Analog mute function control Sampling mode selection Power-save mode selection Audio interface format selection Operation control Digital filter roll-off control Output phase selection Soft mute control Zero flag Digital attenuation mode Not detected 69 0 dB to –63 dB, 0.5 dB step 70 DAMS Disabled 70 DEMP[1:0] 70 AZRO[1:0] Digital de-emphasis function control ZERO1: DIN1, left-channel Zero flag function selection ZERO2: DIN1, right-channel Zero flag polarity selection Digital attenuation level setting High for detection 70 ZREV 0 dB, no attenuation 71–79 ATDAx[7:0] Table 16. Register Map ADR[6:0] (1) DATA[7:0] DEC HEX B7 B6 B5 B4 B3 B2 B1 B0 64 40 MRST SRST AMUTE3 AMUTE2 AMUTE1 AMUTE0 SRDA1 SRDA0 65 41 PSMDA RSV (1) RSV (1) RSV (1) FMTDA3 FMTDA2 FMTDA1 FMTDA0 66 42 OPEDA3 OPEDA2 OPEDA1 OPEDA0 FLT3 FLT2 FLT1 FLT0 67 43 REVDA8 REVDA7 REVDA6 REVDA5 REVDA4 REVDA3 REVDA2 REVDA1 68 44 MUTDA8 MUTDA7 MUTDA6 MUTDA5 MUTDA4 MUTDA3 MUTDA2 MUTDA1 69 45 ZERO8 ZERO7 ZERO6 ZERO5 ZERO4 ZERO3 ZERO2 ZERO1 70 46 DAMS RSV (1) DEMP1 DEMP0 RSV (1) AZRO1 AZRO0 ZREV 71 47 RSV (1) RSV (1) RSV (1) RSV (1) RSV (1) RSV (1) RSV (1) RSV (1) 72 48 ATDA17 ATDA16 ATDA15 ATDA14 ATDA13 ATDA12 ATDA11 ATDA10 73 49 ATDA27 ATDA26 ATDA25 ATDA24 ATDA23 ATDA22 ATDA21 ATDA20 74 4A ATDA37 ATDA36 ATDA35 ATDA34 ATDA33 ATDA32 ATDA31 ATDA30 75 4B ATDA47 ATDA46 ATDA45 ATDA44 ATDA43 ATDA42 ATDA41 ATDA40 76 4C ATDA57 ATDA56 ATDA55 ATDA54 ATDA53 ATDA52 ATDA51 ATDA50 77 4D ATDA67 ATDA66 ATDA65 ATDA64 ATDA63 ATDA62 ATDA61 ATDA60 78 4E ATDA77 ATDA76 ATDA75 ATDA74 ATDA73 ATDA72 ATDA71 ATDA70 79 4F ATDA87 ATDA86 ATDA85 ATDA84 ATDA83 ATDA82 ATDA81 ATDA80 RSV must be set to '0'. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 27 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com REGISTER DEFINITIONS DEC HEX B7 B6 B5 B4 B3 B2 B1 B0 64 40 MRST SRST AMUTE3 AMUTE2 AMUTE1 AMUTE0 SRDA1 SRDA0 MRST Mode control register reset This bit sets the mode control register reset to the default value. Pop noise may be generated. Returning the MRST bit to '1' is unnecessary, because it is automatically set to '1' after the mode control register is reset. Default value = 1. MRST SRST Mode control register reset 0 Set default value 1 Normal operation (default) System reset This bit controls system reset, the resynchronization between the system clock and sampling clock, and DAC operation restart. The mode control register is not reset and the PCM1690 does not go into a power-down state. Returning the SRST bit to '1' is unnecessary; it is automatically set to '1' after triggering a system reset. Default value = 1. SRST System reset 0 Resynchronization 1 Normal operation (default) AMUTE[3:0] Analog mute function control These bits control the enabling/disabling of each source event that triggers the analog mute control circuit. Default value = 0000. AMUTE 28 Analog mute function control xxx0 Disable analog mute control by SCKI lost xxx1 Enable analog mute control by SCKI lost xx0x Disable analog mute control by asynchronous detect xx1x Enable analog mute control by asynchronous detect x0xx Disable analog mute control by ZERO1 and ZERO2 detect x1xx Enable analog mute control by ZERO1 and ZERO2 detect 0xxx Disable analog mute control by DAC disable command 1xxx Enable analog mute control by DAC disable command Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 SRDA[1:0] Sampling mode selection These bits control the sampling mode of DAC operation. In Auto mode, the sampling mode is automatically set according to multiples between the system clock and sampling clock, single rate for 512 fS, 768 fS, and 1152 fS, dual rate for 256 fS or 384 fS, and quad rate for 128 fS and 192 fS. Default value = 00. SRDA Sampling mode selection 00 Auto (default) 01 Single rate 10 Dual rate 11 Quad rate DEC HEX B7 B6 B5 B4 B3 B2 B1 B0 65 41 PSMDA RSV RSV RSV FMTDA3 FMTDA2 FMTDA1 FMTDA0 PSMDA Power-save mode selection This bit selects the power-save mode for the OPEDA[3:0] function. When PSMDA = 0, OPEDA[3:0] controls the power-save mode and normal operation. When PSMDA = 1, OPEDA functions controls the DAC disable (not power-save mode) and normal operation. Default value: 0. PSMDA RSV Power-save mode selection 0 Power-save enable mode (default) 1 Power-save disable mode Reserved Reserved; do not use. FMTDA[3:0] Audio interface format selection These bits control the audio interface format for DAC operation. Details of the format, and any related restrictions with the system clock are described in the Audio Data Interface Formats and Timing section. Default value: 0000 (16-/20-/24-/32-bit I2S format). FMTDA Audio interface format selection 0000 16-/20-/24-/32-bit I2S format (default) 0001 16-/20-/24-/32-bit left-justified format 0010 24-bit right-justified format 0011 16-bit right-justified format 0100 24-bit I2S mode DSP format 0101 24-bit left-justified mode DSP format 0110 24-bit I2S mode TDM format 0111 24-bit left-justified mode TDM format 1000 24-bit high-speed I2S mode TDM format 1001 24-bit high-speed left-justified mode TDM format 101x Reserved 11xx Reserved Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 29 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com DEC HEX B7 B6 B5 B4 B3 B2 B1 B0 66 42 OPEDA3 OPEDA2 OPEDA1 OPEDA0 FLT3 FLT2 FLT1 FLT0 OPEDA[3:0] Operation control These bits control the DAC operation mode. In operation disable mode, the DAC output is cut off from DIN and the internal DAC data are reset. If PSMDA = 1, the DAC output is forced into VCOM. IF PSMDA = 0, the DAC output is forced into AGND and the DAC goes into a power-down state. For normal operating mode, these bits must be '0'. The serial mode control is effective during operation disable mode. Default value: 0000. OPEDA FLT[3:0] Operation control xxx0 DAC1/2 normal operation xxx1 DAC1/2 operation disable with or without power save xx0x DAC3/4 normal operation xx1x DAC3/4 operation disable with or without power save x0xx DAC5/6 normal operation x1xx DAC5/6 operation disable with or without power save 0xxx DAC7/8 normal operation 1xxx DAC7/8 operation disable with or without power save Digital filter roll-off control These bits allow users to select the digital filter roll-off that is best suited to their applications. Sharp and slow filter roll-off selections are available. The filter responses for these selections are shown in the Typical Characteristics section of this data sheet. Default value: 0000. 30 FLT Digital filter roll-off control xxx0 DAC1/2 sharp roll-off xxx1 DAC1/2 slow roll-off xx0x DAC3/4 sharp roll-off xx1x DAC3/4 slow roll-off x0xx DAC5/6 sharp roll-off x1xx DAC5/6 slow roll-off 0xxx DAC7/8 sharp roll-off 1xxx DAC7/8 slow roll-off Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 DEC HEX B7 B6 B5 B4 B3 B2 B1 B0 67 43 REVDA8 REVDA7 REVDA6 REVDA5 REVDA4 REVDA3 REVDA2 REVDA1 REVDA[8:1] Output phase selection These bits are used to control the phase of DAC analog signal outputs. Default value: 0000 0000. REVDA Output phase selection xxxx xxx0 DAC1 normal output xxxx xxx1 DAC1 inverted output xxxx xx0x DAC2 normal output xxxx xx1x DAC2 inverted output xxxx x0xx DAC3 normal output xxxx x1xx DAC3 inverted output xxxx 0xxx DAC4 normal output xxxx 1xxx DAC4 inverted output xxx0 xxxx DAC5 normal output xxx1 xxxx DAC5 inverted output xx0x xxxx DAC6 normal output xx1x xxxx DAC6 inverted output x0xx xxxx DAC7 normal output x1xx xxxx DAC7 inverted output 0xxx xxxx DAC8 normal output 1xxx xxxx DAC8 inverted output Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 31 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com DEC HEX B7 B6 B5 B4 B3 B2 B1 B0 68 44 MUTDA8 MUTDA7 MUTDA6 MUTDA5 MUTDA4 MUTDA3 MUTDA2 MUTDA1 MUTDA[8:1] Soft Mute control These bits are used to enable or disable the Soft Mute function for the corresponding DAC outputs, VOUT. The Soft Mute function is incorporated into the digital attenuators. When mute is disabled (MUTDA[8:1] = 0), the attenuator and DAC operate normally. When mute is enabled by setting MUTDA[8:1] = 1, the digital attenuator for the corresponding output is decreased from the current setting to infinite attenuation. By setting MUTDA[8:1] = 0, the attenuator is increased to the last attenuation level in the same manner as it is for decreasing levels. This configuration reduces pop and zipper noise during muting of the DAC output. This Soft Mute control uses the same resource of digital attenuation level setting. Mute control has priority over the digital attenuation level setting. Default value: 0000 0000. MUTDA 32 Soft Mute control xxxx xxx0 DAC1 Mute disabled xxxx xxx1 DAC1 Mute enabled xxxx xx0x DAC2 Mute disabled xxxx xx1x DAC2 Mute enabled xxxx x0xx DAC3 Mute disabled xxxx x1xx DAC3 Mute enabled xxxx 0xxx DAC4 Mute disabled xxxx 1xxx DAC4 Mute enabled xxx0 xxxx DAC5 Mute disabled xxx1 xxxx DAC5 Mute enabled xx0x xxxx DAC6 Mute disabled xx1x xxxx DAC6 Mute enabled x0xx xxxx DAC7 Mute disabled x1xx xxxx DAC7 Mute enabled 0xxx xxxx DAC8 Mute disabled 1xxx xxxx DAC8 Mute enabled Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 DEC HEX B7 B6 B5 B4 B3 B2 B1 B0 69 45 ZERO8 ZERO7 ZERO6 ZERO5 ZERO4 ZERO3 ZERO2 ZERO1 ZERO[8:1] Zero flag (read-only) These bits indicate the present status of the zero detect circuit for each DAC channel; these bits are read-only. ZERO Zero flag xxxx xxx0 DAC1 zero input not detected xxxx xxx1 DAC1 zero input detected xxxx xx0x DAC2 zero input not detected xxxx xx1x DAC2 zero input detected xxxx x0xx DAC3 zero input not detected xxxx x1xx DAC3 zero input detected xxxx 0xxx DAC4 zero input not detected xxxx 1xxx DAC4 zero input detected xxx0 xxxx DAC5 zero input not detected xxx1 xxxx DAC5 zero input detected xx0x xxxx DAC6 zero input not detected xx1x xxxx DAC6 zero input detected x0xx xxxx DAC7 zero input not detected x1xx xxxx DAC7 zero input detected 0xxx xxxx DAC8 zero input not detected 1xxx xxxx DAC8 zero input detected Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 33 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com DEC HEX B7 B6 B5 B4 B3 B2 B1 B0 70 46 DAMS RSV DEMP1 DEMP0 RSV AZRO1 AZRO0 ZREV DAMS Digital attenuation mode This bit selects the attenuation mode. Default value: 0. DAMS RSV Digital attenuation mode 0 Fine step: 0.5-dB step for 0 dB to –63 dB range (default) 1 Wide range: 1-dB step for 0 dB to –100 dB range Reserved Reserved; do not use. DEMP[1:0] Digital de-emphasis function/sampling rate control These bits are used to disable or enable the various sampling frequencies of the digital de-emphasis function. Default value: 00. DEMP AZRO[1:0] Digital de-emphasis function/sampling rate control 00 Disable (default) 01 48 kHz enable 10 44.1 kHz enable 11 32 kHz enable Zero flag channel combination selection The AZRO[1:0] bits are used to select the zero flag channel combination for ZERO1 and ZERO2. If the analog mute function control by ZERO flags is used, AZRO[1:0] should not be set '00'; otherwise, analog mute works even if the data of DATA2–4 are not zero. Default value: 00B. AZRO ZREV Zero flag combination selection 00 Combination A: ZERO1 = DATA1 left channel, ZERO2 = DATA1 right channel (default) 01 Combination B: ZERO1 = DATA1–4, ZERO2 = DATA1–4 10 Combination C: ZERO1 = DATA4, ZERO2 = DATA1–3 11 Combination D: ZERO1 = DATA1, ZERO2 = DATA2–4 Zero flag polarity selection This bit controls the polarity of the zero flag pin. Default value: 0. 34 ZREV Zero flag polarity selection 0 High for zero detect (default) 1 Low for zero detect Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 DEC HEX B7 B6 B5 B4 B3 B2 B1 B0 71 47 RSV RSV RSV RSV RSV RSV RSV RSV 72 48 ATDA17 ATDA16 ATDA15 ATDA14 ATDA13 ATDA12 ATDA11 ATDA10 73 49 ATDA27 ATDA26 ATDA25 ATDA24 ATDA23 ATDA22 ATDA21 ATDA20 74 4A ATDA37 ATDA36 ATDA35 ATDA34 ATDA33 ATDA32 ATDA31 ATDA30 75 4B ATDA47 ATDA46 ATDA45 ATDA44 ATDA43 ATDA42 ATDA41 ATDA40 76 4C ATDA57 ATDA56 ATDA55 ATDA54 ATDA53 ATDA52 ATDA51 ATDA50 77 4D ATDA67 ATDA66 ATDA65 ATDA64 ATDA63 ATDA62 ATDA61 ATDA60 78 4E ATDA77 ATDA76 ATDA75 ATDA74 ATDA73 ATDA72 ATDA71 ATDA70 79 4F ATDA87 ATDA86 ATDA85 ATDA84 ATDA83 ATDA82 ATDA81 ATDA80 RSV Reserved Reserved; do not use. ATDAx[7:0] Digital attenuation level setting Where x = 1 to 8, corresponding to the DAC output (VOUTx). Each DAC output (VOUT1 through VOUT8) has a digital attenuation function. The attenuation level can be set from 0 dB to R dB, in S-dB steps. Changes in attenuator levels are made by incrementing or decrementing one step (S dB) for every 8/fS time interval until the programmed attenuator setting is reached. Alternatively, the attenuation level can be set to infinite attenuation (or mute). R (Range) and S (Step) is –63 and 0.5 for DAMS = 0 and –100 and 1.0 for DAMS = 1, respectively. The DAMS bit is defined in Register 70 (46h). Table 17 shows attenuation levels for various settings. The attenuation level for each channel can be set individually using the following formula: Attenuation level (dB) = S × (ATDAx[7:0]DEC – 255) where ATDAx[7:0]DEC = 0 through 255. For ATDAx[7:0]DEC = 0 through 128 with DAMS = 0 or 0 through 154 with DAMS = 1, attenuation is set to infinite attenuation (mute). Default value: 1111 1111. Table 17. Attenuation Levels for Various Settings ATDAx[7:0] ATTENUATION LEVEL SETTING BINARY DECIMAL DAMS = 0 DAMS = 1 1111 1111 255 0 dB, no attenuation (default) 0 dB, no attenuation (default) 1111 1110 254 –0.5 dB –1 dB 1111 1101 253 –1.0 dB –2 dB ... ... ... ... 1001 1100 156 –45.9 dB –99 dB 1001 1011 155 –50.0 dB –100 dB 1001 1010 154 –50.5 dB Mute ... ... ... ... 1000 0010 130 –62.5 dB Mute 1000 0001 129 –63.0 dB Mute 0000 0000 128 Mute Mute ... ... ... ... 0000 0000 0 Mute Mute Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 35 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com APPLICATION INFORMATION CONNECTION DIAGRAMS A basic connection diagram is shown in Figure 40, with the necessary power-supply bypassing and decoupling components. Texas Instruments’ PLL170X is used to generate the system clock input at SCKI, as well as to generate the clock for the audio signal processor. The use of series resistors (22 Ω to 100 Ω) are recommended for SCKI, LRCK, BCK, DIN1, DIN2, DIN3, and DIN4 for electromagnetic interference (EMI) reduction. POWER SUPPLY AND GROUNDING The PCM1690 requires +5 V for the analog supply and +3.3 V for the digital supply. The +5-V supply is used to power the DAC analog and output filter circuitry, and the +3.3-V supply is used to power the digital filter and serial interface circuitry. For best performance, it is recommended to use a linear regulator with the +5-V and +3.3-V supplies. Five capacitors are required for supply bypassing (see Figure 40). These capacitors should be located as close as possible to the PCM1690 package. The 10-µF capacitors are aluminum electrolytic, while the three 1-µF capacitors are ceramic. 36 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 PCM1690 R1 R2 R3 Audio DSP or Decoder R4 R5 R6 1 RSV2 RSV2 48 2 RSV1 VCC2 47 3 RSV2 AGND2 46 4 RSV1 RSV2 45 5 RSV2 VOUT1- 44 6 LRCK VOUT1+ 43 7 BCK VOUT2- 42 8 DIN1 VOUT2+ 41 9 DIN2 VOUT3- 40 10 DIN3 VOUT3+ 39 11 DIN4 VOUT4- 38 12 VDD VOUT4+ 37 13 DGND VOUT5- 36 14 SCKI VOUT5+ 35 15 RST VOUT6- 34 16 ZERO1 VOUT6+ 33 17 ZERO2 VOUT7- 32 18 AMUTEI VOUT7+ 31 19 AMUTEO VOUT8- 30 20 MD/SDA/DEMP VOUT8+ 29 C3 C1 R7 PLL170x R8 mC or mP LPF and Buffer R9 21 MC/SCL/FMT 22 MS/ADR0/RSV 23 TEST/ADR1/RSV 24 MODE Termination Circuit RSV2 28 AGND1 27 + VCOM 26 C4 C2 VCC1 25 +5 V + + C6 +3.3 V C5 0V 24 3.3 V R10 24 R10 24 0V (High) (Open) (Low) C1 through C3 are 1-µF ceramic capacitors. C4 through C6 are 10-µF electrolytic capacitors. R1 through R7 are 22-Ω to 100-Ω resistors. R8 and R9 are resistors appropriate for pull-up. R10 is less than 10 kΩ. Figure 40. Basic Connection Diagram Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 37 PCM1690 SBAS448 – OCTOBER 2008.............................................................................................................................................................................................. www.ti.com LOW-PASS FILTER AND DIFFERENTIAL-TO-SINGLE-ENDED CONVERTER FOR DAC OUTPUTS ΔΣ DACs use noise-shaping techniques to improve in-band signal-to-noise ratio (SNR) performance at the expense of generating increased out-of-band noise above the Nyquist frequency, or fS/2. The out-of-band noise must be low-pass filtered in order to provide optimal converter performance. This filtering is accomplished by a combination of on-chip and external low-pass filters. Figure 41 and Figure 42 show the recommended external differential-to-single-ended converter with low-pass active filter circuits for ac-coupled and dc-coupled applications. These circuits are second-order Butterworth filters using a multiple feedback (MFB) circuit arrangement that reduces sensitivity to passive component variations over frequency and temperature. For more information regarding MFB active filter designs, please refer to Applications Bulletin SBAA055, Dynamic Performance Testing of Digital Audio D/A Converters, available from the TI web site (www.ti.com) or the local Texas Instruments' sales office. Because the overall system performance is defined by the quality of the DACs and the associated analog output circuitry, high-quality audio op amps are recommended for the active filters. Texas Instruments’ OPA2134, OPA2353, and NE5532A dual op amps are shown in Figure 41 and Figure 42, and are recommended for use with the PCM1690. R2 C2 R1 R3 47W C1 + VOUT(4 VPP) 10 mF + VOUT+ (4 VPP) 10 mF R1 Analog Output (2 VRMS) R3 R2 C2 NOTE: Amplifier is an NE5532A x1/2 or OPA2134 x1/2; R1 = 7.5-kΩ; R2 = 5.6-kΩ; R3 = 360-Ω; C1 = 3300-pF; C2 = 680-pF; Gain = 0.747; f–3 dB = 53 kHz. Figure 41. AC-Coupled, Post-LPF and Differential to Single-Ended Buffer R2 C2 VOUT+ (4 VPP) VOUT(4 VPP) R1 R3 47W C1 R1 Analog Output (2 VRMS) R3 R2 C2 NOTE: Amplifier is an NE5532A x1/2 or OPA2134 x1/2; R1 = 15-kΩ; R2 = 11-kΩ; R3 = 820-Ω; C1 = 1500-pF; C2 = 330-pF; Gain = 0.733; f–3 dB = 54 kHz. Figure 42. DC-Coupled, Post-LPF and Differential to Single-Ended Buffer 38 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 PCM1690 www.ti.com.............................................................................................................................................................................................. SBAS448 – OCTOBER 2008 PCB LAYOUT GUIDELINES A typical printed circuit board (PCB) layout for the PCM1690 is shown in Figure 43. A ground plane is recommended, with the analog and digital sections being isolated from one another using a split or cut in the circuit board. The PCM1690 should be oriented with the digital I/O pins facing the ground plane split/cut to allow for short, direct connections to the digital audio interface and control signals originating from the digital section of the board. Separate power supplies are recommended for the digital and analog sections of the board. This configuration prevents the switching noise present on the digital supply from contaminating the analog power supply and degrading the dynamic performance of the PCM1690. Digital Power +3.3 VD DGND Analog Power AGND +5 VA +VS -VS VDD VCC Digital Logic and Audio Processor DGND PCM1690 Output Circuits Digital Ground AGND Digital Section Analog Section Analog Ground Return Path for 3.3 VD and Digital Signals Figure 43. Recommended PCB Layout Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): PCM1690 39 PACKAGE OPTION ADDENDUM www.ti.com 13-Nov-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty PCM1690DCA ACTIVE HTSSOP DCA 48 PCM1690DCAR ACTIVE HTSSOP DCA PCM1690DCARG4 ACTIVE HTSSOP DCA 40 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) Cu NiPdAu Level-3-260C-168 HR 48 2000 Green (RoHS & no Sb/Br) Cu NiPdAu Level-3-260C-168 HR 48 2000 Green (RoHS & no Sb/Br) Cu NiPdAu Level-3-260C-168 HR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 21-Nov-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device PCM1690DCAR Package Package Pins Type Drawing SPQ HTSSOP 2000 DCA 48 Reel Reel Diameter Width (mm) W1 (mm) 330.0 24.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 8.6 15.8 1.8 12.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 21-Nov-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) PCM1690DCAR HTSSOP DCA 48 2000 346.0 346.0 41.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated