05220 EMIF4-100LFC Only One Name Means ProTek’Tion™ EMI FILTER/TVS ARRAY APPLICATIONS ✔ Cellular Phones ✔ Notebooks ✔ Personal Digital Assistant (PDA) ✔ Ground Positioning System (GPS) ✔ SMART Cards IEC COMPATIBILITY (EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns 10 BUMP FC FEATURES ✔ ESD Protection > 25 kilovolts ✔ Bidirectional EMI Filtering/TVS Low Pass Filters ✔ Low Insertion Loss: -3db Roll-Off @ 90MHz ✔ Protects Up to Four(4) Data Lines ✔ RoHS Compliant on Lead-Free Versions MECHANICAL CHARACTERISTICS ✔ 10 Bump Flip Chip Package ✔ Weight 0.73 milligrams (Approximate) ✔ Available in Tin-Lead or Lead-Free Plating ✔ Solder Reflow Temperature: Tin-Lead - Sn/Pb, 85/15: 240-245°C Lead-Free - Sn/Ag/Cu, 96/3.5/0.5: 260-270°C ✔ Flammability Rating UL 94V-0 ✔ 8mm Tape and Reel Per EIA Standard 481 PIN CONFIGURATIONS O1 O2 O3 For Each Line O4 I/On G1 G2 100 Ohm I/On 15pF 15pF GND I1 I2 I3 I4 All grounds are connected internally 05220.R1 9/05 1 www.protekdevices.com EMIF4-100LFC DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25°C Unless Otherwise Specified SYMBOL VALUE UNITS TJ -40°C to 85°C °C TSTG -55°C to 150°C °C DC Power Per Resistor P 100 mW Typical Resistance @ ± 20% R 100 OHMS PARAMETER Operating Temperature Storage Temperature ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified PART NUMBER RATED STAND-OFF VOLTAGE MINIMUM BREAKDOWN VOLTAGE MAXIMUM REVERSE LEAKAGE CURRENT TYPICAL FORWARD VOLTAGE MINIMUM ATTENUATION VWM VOLTS @ 1mA V(BR) VOLTS @ 3V ID µA @10mA VF VOLTS 5.0 6.0 0.1 0.8 EMIF4-100LFC CUT-OFF FREQUENCY (50 Ohms I/O ZERO BIAS) TYPICAL CAPACITANCE PER LINE (See Note 1) @ 800-3000 MHz dB fc MHz @2.5V, 1 MHz C Line pF 30 90 30 Note 1: ±20% tolerance. FIGURE 1 RESISTANCE VS TEMPERATURE (Normalized to Resistance at 25°C) Normalized Resistance 1.100 1.060 1.020 0.980 0.940 0.900 -40 05220.R1 9/05 -20 0 20 40 Temperature °C 2 60 80 100 www.protekdevices.com EMIF4-100LFC GRAPHS FIGURE 2 OVERSHOOT & CLAMPING VOLTAGE 5 Volts per Division 35 25 15 5 -5 ESD Test Pulse: +15 kilovolt, 1/30ns (waveform) FIGURE 3 INSERTION LOSS 0 -5 -10 Gain (dB) -15 2.5 Volts -20 -25 -30 0 Volts -35 -40 -45 -50 0.1 05220.R1 9/05 1 10 100 Frequency (MHz) 3 1000 10000 www.protekdevices.com EMIF4-100LFC APPLICATION INFORMATION PRINTED CIRCUIT BOARD RECOMMENDATIONS VALUE PARAMETER Pad Size on PCB Pad Shape Pad Definition Solder Mask Opening Solder Stencil Thickness Solder Stencil Aperture Opening (laser cut, 5% tapered walls) Solder Paste Type Pad Protective Finish Tolerance - Edge To Corner Ball Solder Ball Side Coplanarity Maximum Dwell Time Above Liquidous (183°C) Soldering Maximum Temperature 0.275mm Round Non-Solder Mask Defined Pads 0.325mm Round 0.150mm 0.330mm Round No Clean OSP(Entek Cu Plus 106A) ±50µm ±20µm 60 Seconds 270°C RECOMMENDED NON-SOLDER MASK DEFINED PAD ILLUSTRATION REQUIREMENTS Non-Solder Mask Defined Pad 0.275mm DIA. Temperature: TP for Lead-Free (SnAgCu): 260-270°C TP for Tin-Lead: 240-245°C Preheat time and temperature depends on solder paste and flux activation temperature, component size, weight, surface area & plating. Solder Mask Opening 0.325mm DIA. Solder Stencil Opening 0.330mm DIA. TP Temperature - °C Ramp-up Ramp-down TL TSMAX 155° TSMIN 140° TS - Preheat t 25°C to Peak 30-60 seconds 05220.R1 9/05 Ramp-up 15 seconds 4 Solder Time 15-20 seconds Ramp-down www.protekdevices.com EMIF4-100LFC PACKAGE OUTLINE & DIMENSIONS PACKAGE OUTLINE PACKAGE DIMENSIONS MILLIMETERS BOTTOM VIEW A G D C SIDE VIEW E O F G B H I INCHES DIM MIN MAX MIN MAX A B C D E F G H I J 1.981 1.285 0.495 0.245 0.430 0.430 0.180 0.180 0.432 0.330 2.032 1.375 0.505 0.255 0.440 0.440 0.280 0.280 0.559 0.457 0.0780 0.0506 0.0195 0.0096 0.0169 0.0169 0.0071 0.0071 0.0170 0.0130 0.0800 0.0541 0.0199 0.0100 0.0173 0.0173 0.0110 0.0110 0.0220 0.0180 NOTE: 1. Controlling dimensions in millimeters. 1 2 3 4 I J 0.30 DIA. 63/67 Sn/Pb Solder Bumps Outline & Dimensions: Rev 1 - 8/05, 06060 Tape & Reel Specifications (Dimensions in millimeters) Reel Dia. Tape Width 178mm (7”) 8mm A0 B0 K0 D E F W P0 P2 P t 1.78 ± 0.05 2.18 ± 0.05 0.51 ± 0.05 1.50 ± 0.10 1.75 ± 0.10 3.50 ± 0.05 8.00 ±0.30 4.00 ±0.10 2.00 ±0.05 4.00 ±0.10 0.20±0.025 P0 t P2 D 10 Pitches Cumulative Tolerance on Tape. ± 0.2 E Top cover tape A0 F W K0 B0 P User Direction of Feed TAPE & REEL ORDERING NOMENCLATURE 1. Surface mount product is taped and reeled in accordance with EIA-481. 2. Plastic 8mm Tape: Suffix-T73-1 = 7 Inch Reel - 3,000 pieces per reel, i.e., EMIF4-100LFC-T73-1. 3. Suffix - LF - Lead-Free, i.e., EMIF4-100LFC-LF-T73-1. COPYRIGHT © ProTek Devices 2005 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. 05220.R1 9/05 5 ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: [email protected] Web Site: www.protekdevices.com www.protekdevices.com