ETC NT512D64S8HB0G-75B

NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
512MB, 256MB and 128MB
PC3200, PC2700 and PC2100
Unbuffered DDR DIMM
184 pin Unbuffered DDR DIMM
Based on DDR400/333/266 256M bit B Die device
Features
• 184 Dual In-Line Memory Module (DIMM)
• DRAM DLL aligns DQ and DQS transitions with clock transitions
• Unbuffered DDR DIMM based on 256M bit die B device,
• Address and control signals are fully synchronous to positive
organized as either 32Mbx8 or 16Mbx16
clock edge
• Performance:
• Programmable Operation:
- DIMM CAS Latency: 2, 2.5, 3
PC3200 PC2700 PC2100
fCK
tCK
Speed Sort
5T
6K
75B
DIMM CAS Latency
3
2.5
2.5
Clock Frequency
200
166
133
Clock Cycle
fDQ DQ Burst Frequency
- Burst Type: Sequential or Interleave
Unit
- Burst Length: 2, 4, 8
- Operation: Burst Read and Write
MHz
5
6
7.5
ns
400
333
266
MHz
• Auto Refresh (CBR) and Self Refresh Modes
• Automatic and controlled precharge commands
• Intended for 133, 166 and 200 MHz applications
• 7.8 µs Max. Average Periodic Refresh Interval
• Inputs and outputs are SSTL-2 compatible
• Serial Presence Detect EEPROM
• VDD = VDDQ = 2.5V ± 0.2V (2.6V ± 0.1V for PC3200)
• Gold contacts
• SDRAMs have 4 internal banks for concurrent operation
• SDRAMs are packaged in TSOP packages
• Differential clock inputs
• “Green” packaging – lead free
• Data is read or written on both clock edges
Description
NT512D64S8HB0G, NT512D64S8HB1G, NT512D64S8HB1GY, NT512D72S8PB0G, NT256D64SH88B0G, NT256D64SH88B1G,
NT256D64SH88B1GY, NT256D72S89B0G and NT128D64SH4B1G are unbuffered 184-Pin Double Data Rate (DDR) Synchronous DRAM
Dual In-Line Memory Modules (DIMM). NT512D64S8HB1GY and NT256D64SH88B1GY are packaged using lead free technology.
NT512D64S8HB0G, NT512D64S8HB1G and NT512D64S8HB1GY are 512MB modules organized as dual ranks using sixteen 32Mx8
TSOP devices. NT512D72S8PB0G has ECC and is organized as dual ranks using eighteen 32Mx8 TSOP devices. NT256D64SH88B0G,
NT256D64SH88B1G and NT256D64SH88B1GY are 256MB modules organized as single rank using eight 32Mx8 TSOP devices.
NT256D72S89B0G has ECC and is organized as single rank using nine 32Mx8 TSOP devices. NT128D64SH4B1G are 128MB modules,
organized as single rank using four 16Mx16 TSOP devices.
Depending on the speed grade, these DIMMs are intended for use in applications operating up to 200 MHz clock speeds and achieves
high-speed data transfer rates of up to 400 MHz. Prior to any access operation, the device CAS latency and burst type/ length/operation
type must be programmed into the DIMM by address inputs and I/O inputs BA0 and BA1 using the mode register set cycle.
The DIMM uses a serial EEPROM and through the use of a standard IIC protocol the serial presence-detect implementation (SPD) can be
accessed. The first 128 bytes of the SPD data are programmed with the module characteristics as defined by JEDEC.
REV 2.2
Aug 3, 2004
Preliminary
1
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Ordering Information
Part Number
Organization
NT512D72S8PB0G-5T
Speed
Power
Leads
64Mx72
NT512D64S8HB1G-5T
64Mx64
NT512D64S8HB1GY-5T
(lead free)
NT256D72S890G-5T
PC3200 200MHz (5ns @ CL = 3)
32Mx72
DDR400
2.6V
3-3-3
166MHz (6ns @ CL = 2.5)
NT256D64S88B1G-5T
32Mx64
NT256D64S88B1GY-5T
(lead free)
NT128D64SH4B1G-5T
16Mx64
NT512D64S8HB1G-6K
Gold
64Mx64
NT512D64S8HB1GY-6K
(lead free)
PC2700 166MHz (6ns @ CL = 2.5)
NT256D64S88B1GY-6K
(lead free)
DDR333
2.5-3-3 133MHz (7.5ns @ CL = 2)
32Mx64
NT256D64S88B0G-6K
2.5V
NT128D64SH4B1G-6K
16Mx64
NT512D64S8HB0G-75B
64Mx64
NT256D64S88B0G-75B
32Mx64
NT128D64SH4B1G-75B
PC2100 133MHz (7.5ns @ CL = 2.5)
DDR266B
2.5-3-3 100MHz (10ns @ CL = 2)
16Mx64
For the closest sales office or information, please visit: www.nanya.com
Nanya Technology Corporation
Hwa Ya Technology Park 669
Fu Hsing 3rd Rd., Kueishan,
Taoyuan, 333, Taiwan, R.O.C.
Tel: +886-3-328-1688
REV 2.2
Aug 3, 2004
Preliminary
2
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Pin Description
CK0, CK1, CK2,
Differential Clock Inputs.
DQ0-DQ63
Data input/output
CKE0, CKE1
Clock Enable
DQS0-DQS7
Bidirectional data strobes
RAS
Row Address Strobe
DM0-DM7
Input Data Mask
CAS
Column Address Strobe
VDD
Power
WE
Write Enable
VDDQ
Supply voltage for DQs
S0, S1
Chip Selects
VSS
Ground
CK0, CK1, CK2
A0-A9, A11, A12
Address Inputs
NC
No Connect
A10/AP
Address Input/Auto-precharge
SCL
Serial Presence Detect Clock Input
BA0, BA1
SDRAM Bank Address Inputs
SDA
Serial Presence Detect Data input/output
VREF
Ref. Voltage for SSTL_2 inputs
SA0-2
Serial Presence Detect Address Inputs
VDDID
VDD Identification flag.
VDDSPD
Serial EEPROM positive power supply
Pinout
Pin
Front
Pin
Back
Pin
Front
Pin
Back
Pin
Front
Pin
Back
1
VREF
93
VSS
32
A5
124
VSS
62
VDDQ
154
RAS
2
DQ0
94
DQ4
33
DQ24
125
A6
63
WE
155
DQ45
3
VSS
95
DQ5
34
VSS
126
DQ28
64
DQ41
156
VDDQ
4
DQ1
96
VDDQ
35
DQ25
127
DQ29
65
CAS
157
S0
5
DQS0
97
DM0/DQS9
36
DQS3
128
VDDQ
66
VSS
158
S1
6
DQ2
98
DQ6
37
A4
129
DM3/DQS12
67
DQS5
159
DM5/DQS14
7
VDD
99
DQ7
38
VDD
130
A3
68
DQ42
160
VSS
8
DQ3
100
VSS
39
DQ26
131
DQ30
69
DQ43
161
DQ46
9
NC
101
NC
40
DQ27
132
VSS
70
VDD
162
DQ47
10
NC
102
NC
41
A2
133
DQ31
71
NC
163
NC
11
VSS
103
NC
42
VSS
134
NC
72
DQ48
164
VDDQ
12
DQ8
104
VDDQ
43
A1
135
NC
73
DQ49
165
DQ52
13
DQ9
105
DQ12
44
NC
136
VDDQ
74
VSS
166
DQ53
14
DQS1
106
DQ13
45
NC
137
CK0
75
CK2
167
NC
15
VDDQ
107
DM1/DQS10
46
VDD
138
CK0
76
CK2
168
VDD
16
CK1
108
VDD
47
NC
139
VSS
77
VDDQ
169
DM6/DQS15
17
CK1
109
DQ14
48
A0
140
NC
78
DQS6
170
DQ54
18
VSS
110
DQ15
49
NC
141
A10
79
DQ50
171
DQ55
19
DQ10
111
CKE1
50
VSS
142
NC
80
DQ51
172
VDDQ
20
DQ11
112
VDDQ
51
NC
143
VDDQ
81
VSS
173
NC
21
CKE0
113
NC
52
BA1
144
NC
82
VDDID
174
DQ60
22
VDDQ
114
DQ20
83
DQ56
175
DQ61
23
DQ16
115
A12
53
DQ32
145
84
DQ57
176
VSS
KEY
KEY
VSS
24
DQ17
116
VSS
54
VDDQ
146
DQ36
85
VDD
177
DM7/DQS16
25
DQS2
117
DQ21
55
DQ33
147
DQ37
86
DQS7
178
DQ62
26
VSS
118
A11
56
DQS4
148
VDD
87
DQ58
179
DQ63
27
A9
119
DM2/DQS11
57
DQ34
149
DM4/DQS13
88
DQ59
180
VDDQ
28
DQ18
120
VDD
58
VSS
150
DQ38
89
VSS
181
SA0
29
A7
121
DQ22
59
BA0
151
DQ39
90
WP
182
SA1
30
VDDQ
122
A8
60
DQ35
152
VSS
91
SDA
183
SA2
31
DQ19
123
DQ23
61
DQ40
153
DQ44
92
SCL
184
VDDSPD
Note: All pin assignments are consistent for all 8-byte unbuffered versions.
REV 2.2
Aug 3, 2004
Preliminary
3
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Input/Output Functional Description
Symbol
Type
CK0, CK1, CK2,
CK0, CK1, CK2
CKE0, CKE1
(SSTL)
(SSTL)
Polarity
Cross
point
Active
High
Function
The system clock inputs. All address and command lines are sampled on the cross point of
the rising edge of CK and falling edge of CK. A Delay Locked Loop (DLL) circuit is driven
from the clock inputs and output timing for read operations is synchronized to the input
clock.
Activates the DDR SDRAM CK signal when high and deactivates the CK signal when low.
By deactivating the clocks, CKE low initiates the Power Down mode or the Self Refresh
mode.
Enables the associated DDR SDRAM command decoder when low and disables the
(SSTL)
Active
Low
RAS, CAS, WE
(SSTL)
Active
Low
VREF
Supply
S0, S1
command decoder when high. When the command decoder is disabled, new commands are
ignored but previous operations continue. Physical Bank 0 is selected by S0; Bank 1 is
selected by S1.
VDDQ
Supply
BA0, BA1
(SSTL)
When sampled at the positive rising edge of the clock, RAS, CAS, WE define the operation to
be executed by the SDRAM.
Reference voltage for SSTL-2 inputs
Isolated power supply for the DDR SDRAM output buffers to provide improved noise
immunity
-
Selects which SDRAM bank is to be active.
During a Bank Activate command cycle, A0-A12 defines the row address (RA0-RA12) when
sampled at the rising clock edge.
During a Read or Write command cycle, A0-A9 defines the column address (CA0-CA9)
when sampled at the rising clock edge. In addition to the column address, AP is used to
A0 - A9
A10/AP
A11, A12
(SSTL)
-
invoke auto-precharge operation at the end of the Burst Read or Write cycle. If AP is high,
auto-precharge is selected and BA0/BA1 defines the bank to be precharged. If AP is low,
auto-precharge is disabled.
During a Precharge command cycle, AP is used in conjunction with BA0/BA1 to control
which bank(s) to precharge. If AP is high all 4 banks will be precharged regardless of the
state of BA0/BA1. If AP is low, then BA0/BA1 are used to define which bank to pre-charge.
DQ0 - DQ63
(SSTL)
-
DQS0 - DQS7,
DQS9 – DQS16
(SSTL)
Active
High
CB0 – CB7
(SSTL)
-
DM0 – DM8
Input
Active
High
VDD, VSS
Supply
SA0 – SA2
-
SDA
-
SCL
-
VDDSPD
REV 2.2
Aug 3, 2004
Preliminary
Supply
Data and Check Bit input/output pins operate in the same manner as on conventional
DRAMs.
Data strobes: Output with read data, input with write data. Edge aligned with read data,
centered on write data. Used to capture write data.
Data Check Bit Input/Output pins. Used on ECC modules and is not used on x64 modules.
The data write masks, associated with one data byte. In Write mode, DM operates as a byte
mask by allowing input data to be written if it is low but blocks the write operation if it is high.
In Read mode, DM lines have no effect. DM8 is associated with check bits CB0-CB7, and is
not used on x64 modules.
Power and ground for the DDR SDRAM input buffers and core logic
Address inputs. Connected to either VDD or VSS on the system board to configure the Serial
Presence Detect EEPROM address.
This bi-directional pin is used to transfer data into or out of the SPD EEPROM. A resistor
must be connected from the SDA bus line to V DD to act as a pull-up.
This signal is used to clock data into and out of the SPD EEPROM. A resistor may be
connected from the SCL bus time to V DD to act as a pull-up.
Serial EEPROM positive power supply.
4
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Functional Block Diagram
2 Ranks, 16 devices, 32Mx8 DDR SDRAMs
S1
S0
DQS0
DM0/DQS9
DQS4
DM4/DQS13
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
CS
DQS
D0
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DQS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D8
CS
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D4
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DQS
D12
DQS5
DM5/DQS14
DQS1
DM1/DQS10
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
CS
DQS
D1
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DQS
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D9
DQS
D5
DQS
D13
DQS6
DM6/DQS15
DQS2
DM2/DQS11
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
CS
DQS
D2
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DQS
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D10
DQS
D6
DQS
D14
DQS7
DM7/DQS16
DQS3
DM3/DQS12
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
BA0-BA1
CS
D3
DQS
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
BA0-BA1 : SDRAMs D0-D15
A0-A13
A0-A13 : SDRAMs D0-D15
RAS
RAS : SDRAMs D0-D15
CAS
CAS : SDRAMs D0-D15
CKE0
CKE : SDRAMs D0-D7
CKE1
CKE : SDRAMs D8-D15
WE
Notes :
1.
2.
3.
4.
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
WE : SDRAMs D0-D15
CS
DQS
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D11
SPD
D0-D15
D0-D15
D0-D15
VDDSPD
VDD/VDDQ
VREF
VSS
VDDID
Strap: see Note 4
D7
DQS
DQS
D15
* Clock Wiring
Clock Input
SDRAMs
*CK0/CK0
4 SDRAMs
*CK1/CK1
6 SDRAMs
*CK2/CK2
6 SDRAMs
* Wire per Clock Loading Table/
Wiring Diagrams
Serial PD
SCL
WP
A0
A1
A2
SA0
SA1
SA2
SDA
DQ-to-I/O wiring is shown as recommended but may be changed.
DQ/DQS/DM/CKE/S relationships must be maintained as shown.
DQ, DQS, DM/DQS resistors: 22 Ohms.
VDDID strap connections (for memory device VDD, VDDQ):
STRAP OUT (OPEN): VDD = VDDQ
STRAP IN (VSS): VDD is not equal to VDDQ.
REV 2.2
Aug 3, 2004
Preliminary
5
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Functional Block Diagram
1 Rank, 8 devices, 32Mx8 DDR SDRAMs
S0
DQS0
DM0/DQS9
DQS4
DM4/DQS13
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
CS
DQS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D0
CS
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D4
DQS5
DM5/DQS14
DQS1
DM1/DQS10
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
CS
DQS
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D1
DQS2
DM2/DQS11
DQS
D5
DQS6
DM6/DQS15
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
CS
DQS
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D2
DQS
D6
DQS7
DM7/DQS16
DQS3
DM3/DQS12
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
BA0-BA1
CS
DQS
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D3
DQS
D7
BA0-BA1 : SDRAMs D0-D7
A0-A13
* Clock Wiring
Clock Input
SDRAMs
*CK0/CK0
2 SDRAMs
*CK1/CK1
3 SDRAMs
*CK2/CK2
3 SDRAMs
A0-A13 : SDRAMs D0-D7
RAS
RAS : SDRAMs D0-D7
CAS
CAS : SDRAMs D0-D7
CKE0
CKE : SDRAMs D0-D7
WE
* Wire per Clock Loading Table/
Wiring Diagrams
WE : SDRAMs D0-D7
VDDSPD
VDD/VDDQ
VREF
VSS
VDDID
Serial PD
SCL
WP
Notes :
1.
2.
3.
4.
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
A0
A1
A2
SA0
SA1
SA2
SDA
SPD
D0-D7
D0-D7
D0-D7
Strap: see Note 4
DQ-to-I/O wiring is shown as recommended but may be changed.
DQ/DQS/DM/CKE/S relationships must be maintained as shown.
DQ, DQS, DM/DQS resistors: 22 Ohms.
VDDID strap connections (for memory device VDD, VDDQ):
STRAP OUT (OPEN): VDD = VDDQ
STRAP IN (VSS): VDD is not equal to VDDQ.
REV 2.2
Aug 3, 2004
Preliminary
6
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Functional Block Diagram
1 Rank, 4 devices, 16Mx16 DDR SDRAMs
S0
DQS1
DM1/DQS10
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
LDQS
DQS0
DM0/DQS9
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
UDQS
CS
LDM
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
LDQS
DQS2
DM2/DQS11
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
UDQS
UDQS
CS
LDM
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
D2
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
DQS7
DM7/DQS16
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
LDQS
DQS6
DM6/DQS15
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
UDQS
D1
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
CS
LDM
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
D3
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
BA0-BA1 : SDRAMs D0-D3
A0-A13
* Clock Wiring
Clock Input
SDRAMs
*CK0/CK0
NC
*CK1/CK1
2 SDRAMs
*CK2/CK2
2 SDRAMs
A0-A13 : SDRAMs D0-D3
RAS
RAS : SDRAMs D0-D3
CAS
CAS : SDRAMs D0-D3
CKE0
CKE : SDRAMs D0-D3
WE
* Wire per Clock Loading Table/
Wiring Diagrams
WE : SDRAMs D0-D3
VDDSPD
VDD/VDDQ
VREF
VSS
VDDID
Serial PD
SCL
WP
Notes :
1.
2.
3.
4.
DQS4
DM4/DQS13
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
CS
LDM
I/O 6
I/O 4
I/O 1
I/O 3
I/O 2
I/O 0
I/O 5
I/O 7
BA0-BA1
LDQS
D0
UDM
I/O 8
I/O 10
I/O 15
I/O 13
I/O 12
I/O 14
I/O 11
I/O 9
DQS3
DM3/DQS12
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DQS5
DM5/DQS14
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
A0
A1
A2
SA0
SA1
SA2
SDA
SPD
D0-D3
D0-D3
D0-D3
Strap: see Note 4
DQ-to-I/O wiring is shown as recommended but may be changed.
DQ/DQS/DM/CKE/S relationships must be maintained as shown.
DQ, DQS, DM/DQS resistors: 22 Ohms.
VDDID strap connections (for memory device VDD, VDDQ):
STRAP OUT (OPEN): VDD = VDDQ
STRAP IN (VSS): VDD is not equal to VDDQ.
REV 2.2
Aug 3, 2004
Preliminary
7
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Functional Block Diagram
2 Ranks, 18 devices (ECC), 32Mx8 DDR SDRAMs
S1
S0
DQS0
DM0/DQS9
DQS4
DM4/DQS13
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
CS
DQS
D0
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DQS
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
D9
DQS1
DM1/DQS10
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D4
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DQS
D13
DQS5
DM5/DQS14
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
CS
DQS
D1
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DQS
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
D10
DQS2
DM2/DQS11
DQS
D5
DQS
D14
DQS6
DM6/DQS15
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
CS
DQS
D2
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DQS
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
D11
DQS3
DM3/DQS12
DQS
D6
DQS
D15
DQS7
DM7/DQS16
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D3
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DM
I/O 0
I/O 1
I/O 6
I/O 7
I/O 2
I/O 3
I/O 4
I/O 5
CS
DQS
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
D12
DQS8
DM8/DQS17
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
BA0-BA1
A0-A13
D8
DQS
RAS : SDRAMs D0-D17
CKE0
CKE : SDRAMs D0-D8
CKE1
CKE : SDRAMs D9-D17
Preliminary
DQS
D16
* Clock Wiring
Clock Input
SDRAMs
*CK0/CK0
6 SDRAMs
*CK1/CK1
6 SDRAMs
*CK2/CK2
6 SDRAMs
* Wire per Clock Loading Table/
Wiring Diagrams
Strap: see Note 4
Serial PD
SCL
WP
Notes :
1.
2.
3.
4.
A0-A13 : SDRAMs D0-D17
CAS : SDRAMs D0-D17
Aug 3, 2004
SPD
D0-D8
D0-D8
D0-D8
VDDSPD
VDD/VDDQ
VREF
VSS
VDDID
BA0-BA1 : SDRAMs D0-D17
RAS
REV 2.2
D7
D17
CAS
WE
DQS
DQS
A0
A1
A2
SA0
SA1
SA2
SDA
DQ-to-I/O wring may be changed within a byte.
DQ/DQS/DM/CKE/S relationships are maintained as shown.
DQ/DQS/DM/DQS resistors are 22 Ohms.
VDDID strap connections (for memory device VDD, VDDQ):
STRAP OUT (OPEN): VDD = VDDQ
STRAP IN (VSS): VDD is not equal to VDDQ.
WE : SDRAMs D0-D17
8
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Functional Block Diagram
1 Rank, 9 devices (ECC), 32Mx8 DDR SDRAMs
S0
DQS0
DM0/DQS9
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQS4
DM4/DQS13
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D0
DQS1
DM1/DQS10
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D1
BA0-BA1
A0-A13
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D2
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
DQS
D3
CS
DQS
D5
CS
DQS
D6
CS
DQS
D7
Serial PD
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
CS
SCL
DQS
WP
D8
VDDSPD
VDD/VDDQ
VREF
VSS
VDDID
A0
A1
A2
SA0
SA1
SA2
SDA
SPD
D0-D8
D0-D8
D0-D8
Strap: see Note 4
* Clock Wiring
Clock Input
SDRAMs
*CK0/CK0
3 SDRAMs
*CK1/CK1
3 SDRAMs
*CK2/CK2
3 SDRAMs
* Wire per Clock Loading Table/
Wiring Diagrams
BA0-BA1 : SDRAMs D0-D8
A0-A13 : SDRAMs D0-D8
CAS
CAS : SDRAMs D0-D8
CKE : SDRAMs D0-D8
Preliminary
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ56
DQ57
DQ58
DQ59
DQ60
DQ61
DQ62
DQ63
CKE0
Aug 3, 2004
D4
DQS7
DM7/DQS16
RAS : SDRAMs D0-D8
REV 2.2
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
RAS
WE
DQS
DQS6
DM6/DQS15
DQS8
DM8/DQS17
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ40
DQ41
DQ42
DQ43
DQ44
DQ45
DQ46
DQ47
DQS3
DM3/DQS12
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
CS
DQS5
DM5/DQS14
DQS2
DM2/DQS11
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DM
I/O 7
I/O 6
I/O 1
I/O 0
I/O 5
I/O 4
I/O 3
I/O 2
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
WE : SDRAMs D0-D8
Notes :
1. DQ-to-I/O wring may be changed within a byte.
2. DQ/DQS/DM/CKE/S relationships are maintained as shown.
3. DQ/DQS/DM/DQS resistors are 22 Ohms.
4. VDDID strap connections (for memory device VDD, VDDQ):
STRAP OUT (OPEN): VDD = VDDQ
STRAP IN (VSS): VDD is not equal to VDDQ.
9
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Serial Presence Detect
SPD Description
Byte
0
Description
Number of Serial PD Bytes Written during Production
Byte
26
Description
Maximum Data Access Time from Clock at CL=1
1
Total Number of Bytes in Serial PD device
27
Minimum Row Precharge Time (tRP)
2
Fundamental Memory Type
28
Minimum Row Active to Row Active delay (tRRD)
3
Number of Row Addresses on Assembly
29
Minimum RAS to CAS delay (tRCD)
4
Number of Column Addresses on Assembly
30
Minimum RAS Pulse Width (tRAS)
5
Number of DIMM Rank
31
Module Bank Density
6
Data Width of Assembly
32
Address and Command Setup Time Before Clock
7
Data Width of Assembly (cont’)
33
Address and Command Hold Time After Clock
8
Voltage Interface Level of this Assembly
34
Data Input Setup Time Before Clock
35
Data Input Hold Time After Clock
9
10
DDR SDRAM Device Cycle Time
CL=2.5
DDR SDRAM Device Access Time from Clock
CL=2.5
36-40
Reserved
11
DIMM Configuration Type
41
12
Refresh Rate/Type
42
13
Primary DDR SDRAM Width
43
Max Cycle Time (tCK max)
Error Checking DDR SDRAM Device Width
44
Maximum DQS-DQ Skew Time (tDQSQ)
45
Maximum Read Data Hold Skew Factor (tQHS)
14
15
16
17
18
19
DDR SDRAM Device Attr: Min CLK Delay, Random Col
Access
DDR SDRAM Device Attributes: Burst Length
Supported
46-61
DDR SDRAM Device Attributes: Number of Device
Banks
DDR SDRAM Device Attributes:
CAS Latencies Supported
DDR SDRAM Device Attributes: CS Latency
Minimum Active/Auto-refresh Time (tRC)
Auto-refresh to Active/Auto-refresh Command Period
(tRFC)
Reserved
62
SPD Revision
63
Checksum Data
64-71
20
DDR SDRAM Device Attributes: WE Latency
21
DDR SDRAM Device Attributes:
73-90
72
22
DDR SDRAM Device Attributes: General
91-92
Manufacturer’s JEDEC ID Code
Module Manufacturing Location
Module Part number
Module Revision Code
Module Manufacturing Data
23
Minimum Clock Cycle
CL=2.5
yy= Binary coded decimal year code, 0-99(Decimal),
93-94
00-63(Hex)
ww= Binary coded decimal year code, 01-52(Decimal),
01-34(Hex)
24
25
Maximum Data Access Time from Clock at
CL=2
Minimum Clock Cycle Time at CL=1
REV 2.2
Aug 3, 2004
Preliminary
95-98
Module Serial Number
99-127
Reserved
10
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
SPD Values for NT512D64S8HBxGx
PC3200 (5T)
PC2700 (6K)
PC2100 (75B)
Byte
Value
Hex
Value
Hex
Value
Hex
0
128
80
128
80
128
80
1
256
08
256
08
256
08
2
SDRAM DDR
07
SDRAM DDR
07
SDRAM DDR
07
3
13
0D
13
0D
13
0D
4
10
0A
10
0A
10
0A
5
2
02
2
02
2
02
6
x64
40
x64
40
x64
40
7
x64
00
x64
00
x64
00
8
SSTL 2.5V
04
SSTL 2.5V
04
SSTL 2.5V
04
9
5.0ns
50
6.0ns
60
7.5ns
75
10
6.0ns
60
7.0ns
70
7.5ns
75
11
Non-Parity
00
Non-Parity
00
Non-Parity
00
12
SR/1x(7.8us)
82
SR/1x(7.8us)
82
SR/1x(7.8us)
82
13
x8
08
x8
08
x8
08
14
N/A
00
N/A
00
N/A
00
15
1 Clock
01
1 Clock
01
1 Clock
01
16
2,4,8
0E
2,4,8
0E
2,4,8
0E
17
4
04
4
04
4
04
18
2/2.5/3
1C
2/2.5
0C
2/2.5
0C
19
0
01
0
01
0
01
20
1
02
1
02
1
02
21
Differential Clock
20
Differential Clock
20
Differential Clock
20
22
±0.1V Tolerance
00
±0.2V Tolerance
00
±0.2V Tolerance
00
23
6ns
60
7.5ns
75
10ns
A0
24
0.70ns
70
0.70ns
70
0.75ns
75
25
7.5ns
75
N/A
00
N/A
00
26
7.5ns
75
N/A
00
N/A
00
27
15ns
3C
18ns
48
20ns
50
28
10ns
28
12ns
30
15ns
3C
29
15ns
3C
18ns
48
20ns
50
30
40ns
28
42ns
2A
45ns
2D
31
256MB
40
256MB
40
256MB
40
32
0.60ns
60
0.75ns
75
0.90ns
90
33
0.60ns
60
0.75ns
75
0.90ns
90
34
0.40ns
40
0.45ns
45
0.50ns
50
35
0.40ns
40
0.45ns
45
0.50ns
50
36-40
Reserved
00
Reserved
00
Reserved
00
41
55ns
37
60ns
3C
65ns
41
42
70ns
46
72ns
48
75ns
4B
43
8ns
20
12ns
30
12ns
30
44
0.4ns
28
0.4ns
28
0.5ns
32
45
0.50ns
50
0.55ns
55
0.75ns
75
46-61
Reserved
00
Reserved
00
Reserved
00
62
Initial
00
Initial
00
Initial
00
63
Checksum
8F
Checksum
3C
Checksum
64-71
NANYA
7F7F7F0B
NANYA
00000000
7F7F7F0B
NANYA
00000000
23
7F7F7F0B
00000000
72
Assembly
--
Assembly
--
Assembly
--
73-90
Module PN
--
Module PN
--
Module PN
--
91-92
Revision
--
Revision
--
Revision
--
93-94
Year/Week Code
--
Year/Week Code
--
Year/Week Code
--
95-98
Serial Number
--
Serial Number
--
Serial Number
--
99-127
Reserved
--
Reserved
--
Reserved
--
REV 2.2
Aug 3, 2004
Preliminary
11
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
SPD Values for NT256D64S88BxGx
PC3200 (5T)
PC2700 (6K)
PC2100 (75B)
Byte
Value
Hex
Value
Hex
Value
Hex
0
128
80
128
80
128
80
1
256
08
256
08
256
08
2
SDRAM DDR
07
SDRAM DDR
07
SDRAM DDR
07
3
13
0D
13
0D
13
0D
4
10
0A
10
0A
10
0A
5
1
01
1
01
1
01
6
x64
40
x64
40
x64
40
7
x64
00
x64
00
x64
00
8
SSTL 2.5V
04
SSTL 2.5V
04
SSTL 2.5V
04
9
5.0ns
50
6.0ns
60
7.5ns
75
10
6.0ns
60
7.0ns
70
7.5ns
75
11
Non-Parity
00
Non-Parity
00
Non-Parity
00
12
SR/1x(7.8us)
82
SR/1x(7.8us)
82
SR/1x(7.8us)
82
13
x8
08
x8
08
x8
08
14
N/A
00
N/A
00
N/A
00
15
1 Clock
01
1 Clock
01
1 Clock
01
16
2,4,8
0E
2,4,8
0E
2,4,8
0E
17
4
04
4
04
4
04
18
2.5/3
18
2/2.5
0C
2/2.5
0C
19
0
01
0
01
0
01
20
1
02
1
02
1
02
21
Differential Clock
20
Differential Clock
20
Differential Clock
20
22
±0.1V Tolerance
00
±0.2V Tolerance
00
±0.2V Tolerance
00
23
5ns
50
7.5ns
75
10ns
A0
24
0.60ns
60
0.70ns
70
0.75ns
75
25
N/A
00
N/A
00
N/A
00
26
N/A
00
N/A
00
N/A
00
27
15ns
3C
18ns
48
20ns
50
28
10ns
28
12ns
30
15ns
3C
29
15ns
3C
18ns
48
20ns
50
30
40ns
28
42ns
2A
45ns
2D
31
256MB
40
256MB
40
256MB
40
32
0.60ns
60
0.75ns
75
0.90ns
90
33
0.60ns
60
0.75ns
75
0.90ns
90
34
0.40ns
40
0.45ns
45
0.50ns
50
35
0.40ns
40
0.45ns
45
0.50ns
50
36-40
Reserved
00
Reserved
00
Reserved
00
41
60ns
3C
60ns
3C
60ns
3C
42
72ns
48
72ns
48
72ns
48
43
12ns
30
12ns
30
12ns
30
44
0.4ns
28
0.4ns
28
0.4ns
28
45
0.55ns
55
0.55ns
55
0.55ns
55
46-61
Reserved
00
Reserved
00
Reserved
00
62
Initial
00
Initial
00
Initial
00
63
Checksum
9C
Checksum
3B
Checksum
F0
64-71
NANYA
7F7F7F0B
NANYA
00000000
7F7F7F0B
NANYA
00000000
7F7F7F0B
00000000
72
Assembly
--
Assembly
--
Assembly
--
73-90
Module PN
--
Module PN
--
Module PN
--
91-92
Revision
--
Revision
--
Revision
--
93-94
Year/Week Code
--
Year/Week Code
--
Year/Week Code
--
95-98
Serial Number
--
Serial Number
--
Serial Number
--
99-127
Reserved
--
Reserved
--
Reserved
--
REV 2.2
Aug 3, 2004
Preliminary
12
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
SPD Values for NT128D64SH4B1G
PC3200 (5T)
PC2700 (6K)
PC2100 (75B)
Byte
Value
Hex
Value
Hex
Value
Hex
0
128
80
128
80
128
80
1
256
08
256
08
256
08
2
SDRAM DDR
07
SDRAM DDR
07
SDRAM DDR
07
3
13
0D
13
0D
13
0D
4
9
09
9
09
9
09
5
1
01
1
01
1
01
6
x64
40
x64
40
x64
40
7
x64
00
x64
00
x64
00
8
SSTL 2.5V
04
SSTL 2.5V
04
SSTL 2.5V
04
9
5.0ns
50
6.0ns
60
7.5ns
75
10
6.0ns
60
7.0ns
70
7.5ns
75
11
Non-Parity
00
Non-Parity
00
Non-Parity
00
12
SR/1x(7.8us)
82
SR/1x(7.8us)
82
SR/1x(7.8us)
82
13
x16
10
x16
10
x16
10
14
N/A
00
N/A
00
N/A
00
15
1 Clock
01
1 Clock
01
1 Clock
01
16
2,4,8
0E
2,4,8
0E
2,4,8
0E
17
4
04
4
04
4
04
18
2.5/3
18
2/2.5
0C
2/2.5
0C
19
0
01
0
01
0
01
20
1
02
1
02
1
02
21
Differential Clock
20
Differential Clock
20
Differential Clock
20
22
±0.1V Tolerance
00
±0.2V Tolerance
00
±0.2V Tolerance
00
23
5ns
50
7.5ns
75
10ns
A0
24
0.60ns
60
0.70ns
70
0.75ns
75
25
N/A
00
N/A
00
N/A
00
26
N/A
00
N/A
00
N/A
00
27
15ns
3C
18ns
48
20ns
50
28
10ns
28
12ns
30
15ns
3C
29
15ns
3C
18ns
48
20ns
50
30
40ns
28
42ns
2A
45ns
2D
31
128MB
20
128MB
20
128MB
20
32
0.60ns
60
0.75ns
75
0.90ns
90
33
0.60ns
60
0.75ns
75
0.90ns
90
34
0.40ns
40
0.45ns
45
0.50ns
50
35
0.40ns
40
0.45ns
45
0.50ns
50
36-40
Reserved
00
Reserved
00
Reserved
00
41
60ns
3C
60ns
3C
60ns
3C
42
72ns
48
72ns
48
72ns
48
43
12ns
30
12ns
30
12ns
30
44
0.4ns
28
0.4ns
28
0.4ns
28
45
0.55ns
55
0.55ns
55
0.55ns
55
46-61
Reserved
00
Reserved
00
Reserved
00
62
Initial
00
Initial
00
Initial
00
63
Checksum
83
Checksum
22
Checksum
D7
64-71
NANYA
7F7F7F0B
NANYA
00000000
7F7F7F0B
NANYA
00000000
7F7F7F0B
00000000
72
Assembly
--
Assembly
--
Assembly
--
73-90
Module PN
--
Module PN
--
Module PN
--
91-92
Revision
--
Revision
--
Revision
--
93-94
Year/Week Code
--
Year/Week Code
--
Year/Week Code
--
95-98
Serial Number
--
Serial Number
--
Serial Number
--
99-127
Reserved
--
Reserved
--
Reserved
--
REV 2.2
Aug 3, 2004
Preliminary
13
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
SPD Values for NT512D72S8PB0G
PC3200 (5T)
Byte
Value
Hex
0
128
80
1
256
08
2
SDRAM DDR
07
3
13
0D
4
10
0A
5
2
02
6
x74
48
7
x74
00
8
SSTL 2.5V
04
9
5.0ns
50
10
6.0ns
60
11
Parity
02
12
SR/1x(7.8us)
82
13
x8
08
14
ECC Width
08
15
1 Clock
01
16
2,4,8
0E
17
4
04
18
2.5/3
18
19
0
01
20
1
02
21
Differential Clock
20
22
±0.1V Tolerance
00
23
5ns
50
24
0.60ns
60
25
N/A
00
26
N/A
00
27
15ns
3C
28
10ns
28
29
15ns
3C
30
40ns
28
31
256MB
40
32
0.60ns
60
33
0.60ns
60
34
0.40ns
40
35
0.40ns
40
36-40
Reserved
00
41
60ns
3C
42
72ns
48
43
12ns
30
44
0.4ns
28
45
0.55ns
55
46-61
Reserved
00
62
Initial
00
63
Checksum
AF
64-71
NANYA
72
Assembly
--
73-90
Module PN
--
91-92
Revision
--
93-94
Year/Week Code
--
95-98
Serial Number
--
99-127
Reserved
--
7F7F7F0B
00000000
REV 2.2
Aug 3, 2004
Preliminary
14
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
SPD Values for NT256D72S89B0G
PC3200 (5T)
Byte
Value
Hex
0
128
80
1
256
08
2
SDRAM DDR
07
3
13
0D
4
10
0A
5
1
01
6
x72
48
7
x72
00
8
SSTL 2.5V
04
9
5.0ns
50
10
6.0ns
60
11
Parity
02
12
SR/1x(7.8us)
82
13
x8
08
14
ECC Width
08
15
1 Clock
01
16
2,4,8
0E
17
4
04
18
2.5/3
18
19
0
01
20
1
02
21
Differential Clock
20
22
±0.1V Tolerance
00
23
5ns
50
24
0.60ns
60
25
N/A
00
26
N/A
00
27
15ns
3C
28
10ns
28
29
15ns
3C
30
40ns
28
31
256MB
40
32
0.60ns
60
33
0.60ns
60
34
0.40ns
40
35
0.40ns
40
36-40
Reserved
00
41
60ns
3C
42
72ns
48
43
12ns
30
44
0.4ns
28
45
0.55ns
55
46-61
Reserved
00
62
Initial
00
63
Checksum
AE
64-71
NANYA
72
Assembly
--
73-90
Module PN
--
91-92
Revision
--
93-94
Year/Week Code
--
95-98
Serial Number
--
99-127
Reserved
--
7F7F7F0B
00000000
REV 2.2
Aug 3, 2004
Preliminary
15
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Absolute Maximum Ratings
Symbol
VIN, VOUT
Parameter
Voltage on I/O pins relative to VSS
Rating
Units
-0.5 to VDDQ +0.5
V
VIN
Voltage on Input relative to VSS
-0.5 to +3.6
V
VDD
Voltage on VDD supply relative to VSS
-0.5 to +3.6
V
VDDQ
Voltage on VDDQ supply relative to VSS
-0.5 to +3.6
V
0 to +70
°C
-55 to +150
°C
W
mA
TA
TSTG
Operating Temperature (Ambient)
Storage Temperature (Plastic)
PD
Power Dissipation (per device component)
1
IOUT
Short Circuit Output Current
50
Note: Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is stress
rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
DC Electrical Characteristics and Operating Conditions
TA= 0°C ~ 70°C; VDDQ= VDD= 2.5V±0.2V(PC2100,PC2700); TA= 0°C ~ 70°C; VDDQ= VDD= 2.6V±0.1V(PC3200)
Symbol
VDD
VDDQ
VSS, VSSQ
VREF
VTT
Parameter
Max
Units
Notes
2.7
V
1
2.7
V
1
0
0
V
I/O Reference Voltage
0.49 x VDDQ
0.51 x VDDQ
V
1, 2
Supply Voltage
I/O Supply Voltage
Min
PC2100, PC2700
2.3
PC3200
2.5
PC2100, PC2700
2.3
PC3200
2.5
Supply Voltage, I/O Supply Voltage
I/O Termination Voltage (System)
VREF – 0.04
VREF + 0.04
V
1, 3
VIH (DC)
Input High (Logic1) Voltage
VREF + 0.15
VDDQ + 0.3
V
1
VIL (DC)
Input Low (Logic0) Voltage
-0.3
VREF - 0.15
V
1
VIN (DC)
Input Voltage Level, CK and CK Inputs
-0.3
VDDQ + 0.3
V
1
VID (DC)
Input Differential Voltage, CK and CK Inputs
0.30
VDDQ + 0.6
V
1, 4
-10
10
µA
1
-10
10
µA
1
-16.8
-
mA
1
16.8
-
mA
1
Input Leakage Current
II
Any input 0V ≤ VIN ≤ VDD;
All other pins not under test = 0V
Output Leakage Current
IOZ
DQs are disabled; 0V ≤ Vout ≤ VDDQ
Output High Current
IOH
(VOUT = VDDQ -0.373V, min VREF, min VTT)
Output Low Current
IOL
(VOUT = 0.373, max VREF, max VTT)
1. Inputs are not recognized as valid until VREF stabilizes.
2. VREF is expected to be equal to 0.5 VDDQ of the transmitting device, and to track variations in the DC level of the same. Peak-to-peak
noise on VREF may not exceed 2% of the DC value.
3. VTT is not applied directly to the DIMM. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF,
and must track variations in the DC level of VREF.
4. VID is the magnitude of the difference between the input level on CK and the input level on CK.
REV 2.2
Aug 3, 2004
Preliminary
16
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
AC Characteristics
Notes 1-5 apply to the following Tables; Electrical Characteristics and DC Operating Conditions, AC Operating
Conditions, Operating, Standby, and Refresh Currents, and Electrical Characteristics and AC Timing.)
1. All voltages referenced to VSS.
2. Tests for AC timing, IDD, and electrical, AC and DC characteristics, may be conducted at nominal reference/supply voltage levels, but the
related specifications and device operation are guaranteed for the full voltage range specified.
3. Outputs measured with equivalent load. Refer to the AC Output Load Circuit below.
4. AC timing and IDD tests may use a VIL to VIH swing of up to 1.5V in the test environment, but input timing is still referenced to VREF (or to
the crossing point for CK, CK), and parameter specifications are guaranteed for the specified AC input levels under normal use conditions.
The minimum slew rate for the input signals is 1V/ns in the range between VIL (AC) and VIH (AC) unless otherwise specified.
5. The AC and DC input level specifications are as defined in the SSTL_2 Standard (i.e. the receiver effectively switches as a result of the
signal crossing the AC input level, and remains in that state as long as the signal does not ring back above (below) the DC input LOW
(HIGH) level.
AC Output Load Circuits
VTT
50 ohms
Output
Timing Reference Point
VOUT
30 pF
AC Operating Conditions
TA = 0 °C ~ 70 °C; VDDQ= VDD= 2.5V ± 0.2V (PC2100/PC2700); VDDQ= VDD= 2.6V ± 0.1V (PC3200)
Symbol
Parameter/Condition
Min
VIH (AC)
Input High (Logic 1) Voltage.
VIL (AC)
Input Low (Logic 0) Voltage.
VID (AC)
Input Differential Voltage, CK and CK Inputs
VIX (AC)
Input Differential Pair Cross Point Voltage, CK and CK Inputs
Max
Unit
Notes
V
1, 2
VREF - 0.31
V
1, 2
0.62
VDDQ + 0.6
V
1, 2, 3
(0.5* VDDQ) - 0.2
(0.5* VDDQ) + 0.2
V
1, 2, 4
VREF + 0.31
1. Input slew rate = 1V/ ns.
2. Inputs are not recognized as valid until VREF stabilizes.
3. VID is the magnitude of the difference between the input level on CK and the input level on CK.
4. The value of VIX is expected to equal 0.5*VDDQ of the transmitting device and must track variations in the DC level of the same.
REV 2.2
Aug 3, 2004
Preliminary
17
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Operating, Standby, and Refresh Currents
TA = 0 °C ~ 70 °C; VDDQ= VDD= 2.5V ± 0.2V (PC2100/PC2700); VDDQ= VDD= 2.6V ± 0.1V (PC3200)
Symbol
IDD0
IDD1
IDD2P
IDD2N
IDD3P
IDD3N
IDD4R
IDD4W
Parameter/Condition
clock cycle; address and control inputs changing once per clock cycle
Operating Current: one bank; active/read/precharge; Burst = 2; tRC = tRC (MIN); CL=2.5; tCK = tCK (MIN); IOUT = 0mA; address and
control inputs changing once per clock cycle
Precharge Power-Down Standby Current: all banks idle; power-down mode; CKE ≤ VIL (MAX); tCK = tCK (MIN)
Idle Standby Current: CS ≥ VIH (MIN); all banks idle; CKE ≥ VIH (MIN); tCK = tCK (MIN); address and control inputs changing once
per clock cycle
Active Power-Down Standby Current: one bank active; power-down mode; CKE ≤ VIL (MAX); tCK = tCK (MIN)
Active Standby Current: one bank; active/precharge; CS ≥ VIH (MIN); CKE ≥ VIH (MIN); tRC = tRAS (MAX); tCK = tCK (MIN); DQ, DM, and
DQS inputs changing twice per clock cycle; address and control inputs changing once per clock cycle
Operating Current: one bank; Burst = 2; reads; continuous burst; address and control inputs changing once per clock cycle;
DQ and DQS outputs changing twice per clock cycle; CL = 2.5; tCK = tCK (MIN); IOUT = 0mA
Operating Current: one bank; Burst = 2; writes; continuous burst; address and control inputs changing once per clock cycle;
DQ and DQS inputs changing twice per clock cycle; CL=2.5; tCK = tCK (MIN)
IDD5
Auto-Refresh Current: tRC = tRFC (MIN)
IDD6
Self-Refresh Current: CKE ≤ 0.2V
IDD7
Notes
Operating Current: one bank; active/precharge; tRC = tRC (MIN); tCK = tCK (MIN); DQ, DM, and DQS inputs changing twice per
1,2
1,2
1,2
1,2
1,2
1,2
1,2
1,2
1,2,3
1,2
Operating Current: four bank; four bank interleaving with BL = 4, address and control inputs randomly changing; 50% of
data changing at every transfer; tRC = tRC (min); IOUT = 0mA.
1,2
1. IDD specifications are tested after the device is properly initialized.
2. Input slew rate = 1V/ ns.
3. Current at 7.8 µs is time averaged value of IDD5 at tRFC (MIN) and IDD2P over 7.8 µs.
All IDD current values are calculated from device level.
REV 2.2
Aug 3, 2004
Preliminary
18
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
NT512D64S8HB1Gx
NT256D64S88B1Gx
NT128D64SH4B1G
PC3200
PC2700
PC2100
PC3200
PC2700
PC2100
PC3200
PC2700
PC2100
(5T)
(6K)
(75B)
(5T)
(6K)
(75B)
(5T)
(6K)
(75B)
IDD0
1915
1755
1585
995
915
825
460
420
380
IDD1
1995
1995
1825
1035
1035
945
480
480
440
IDD2P
340
340
340
180
180
180
80
80
80
IDD2N
765
765
680
405
405
360
180
180
160
IDD3P
357
357
306
189
189
162
84
84
72
IDD3N
1275
1275
1105
675
675
585
300
300
260
IDD4R
3275
3275
2705
1675
1675
1385
800
800
660
IDD4W
3195
3195
2625
1635
1635
1345
780
780
640
IDD5
3675
2875
2785
1875
1475
1425
900
700
680
IDD6
51
51
51
27
27
27
12
12
12
IDD7
5275
5275
4065
2675
2675
2065
1300
1300
1000
Symbol
NT512D72S8PB0G
NT256256D64S89B0G
PC3200
PC2700
PC2100
PC3200
PC2700
PC2100
(5T)
(6K)
(75B)
(5T)
(6K)
(75B)
IDD0
1915
1755
1585
995
915
825
IDD1
1995
1995
1825
1035
1035
945
IDD2P
340
340
340
180
180
180
IDD2N
765
765
680
405
405
360
IDD3P
357
357
306
189
189
162
IDD3N
1275
1275
1105
675
675
585
IDD4R
3275
3275
2705
1675
1675
1385
IDD4W
3195
3195
2625
1635
1635
1345
IDD5
3675
2875
2785
1875
1475
1425
IDD6
51
51
51
27
27
27
IDD7
5275
5275
4065
2675
2675
2065
Symbol
REV 2.2
Aug 3, 2004
Preliminary
19
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
AC Timing Specifications for DDR SDRAM Devices Used on Module
TA = 0 °C ~ 70 °C; VDDQ= VDD= 2.5V ± 0.2V (PC2100/PC2700); VDDQ= VDD= 2.6V ± 0.1V (PC3200) (Part 1 of 2)
Symbol
tAC
tDQSCK
Parameter
5T
6K
75B
PC3200
PC2700
PC2100
Unit
Notes
Min.
Max.
Min.
Max.
Min.
Max.
DQ output access time from CK/CK
-0.65
+0.65
-0.7
+0.7
-0.75
+0.75
ns
1-4
DQS output access time from CK/CK
-0.55
+0.55
-0.7
+0.7
-0.75
+0.75
ns
1-4
tCH
CK high-level width
0.45
0.55
0.45
0.55
0.45
0.55
tCK
1-4
tCL
CK low-level width
0.45
0.55
0.45
0.55
0.45
0.55
tCK
1-4
tCK
Clock cycle time CL=3
5
8
-
-
-
-
tCK
Clock cycle time CL=2.5
6
12
6
12
7.5
12
ns
1-4
tCK
Clock cycle time CL=2
-
-
7.5
12
10
12
ns
1-4
tDH
DQ and DM input hold time
0.4
0.45
0.5
ns
tDS
DQ and DM input setup time
0.4
0.45
0.5
ns
tDIPW
DQ and DM input pulse width (each input)
1.75
1.75
1.75
ns
1-4
tHZ
Data-out high-impedance time from CK/CK
-0.6
+0.6
-0.7
+0.7
-0.75
+0.75
ns
1-4, 5
tLZ
Data-out low-impedance time from CK/CK
-0.6
+0.6
-0.7
+0.7
-0.75
+0.75
ns
1-4, 5
0.5
ns
1-4
tCK
1-4
tCK
1-4
0.75
ns
1-4
1.25
tCK
1-4
tDQSQ
tHP
tQH
DQS-DQ skew (DQS & associated DQ signals)
0.4
0.45
Minimum half clk period for any given cycle;
tCH or
tCH or
tCH or
defined by clk high (tCH) or clk low (tCL) time
tCL
tCL
tCL
tHP -
tHP -
tHP -
tQHS
tQHS
tQHS
Data output hold time from DQS
tQHS
Data hold Skew Factor
tDQSS
Write command to 1st DQS latching transition
tDQSL,
DQS input low (high) pulse width
tDQSH
(write cycle)
0.5
0.75
1.25
0.55
0.75
1.25
0.75
1-4,
15, 16
1-4,
15, 16
0.35
0.35
0.35
tCK
1-4
0.2
0.2
0.2
tCK
1-4
0.2
0.2
0.2
tCK
1-4
Mode register set command cycle time
2
2
2
tCK
1-4
tWPRES
Write preamble setup time
0
0
0
ns
1-4, 7
tWPST
Write postamble
0.40
tCK
1-4, 6
tWPRE
Write preamble
0.25
0.25
0.25
tCK
1-4
0.6
0.75
0.9
ns
0.6
0.75
0.9
ns
0.7
0.8
1.0
ns
tDSS
tDSH
tMRD
tIH
tIS
tIH
DQS falling edge to CK setup time
(write cycle)
DQS falling edge hold time from CK
(write cycle)
Address and control input hold time
(fast slew rate)
Address and control input setup time
(fast slew rate)
Address and control input hold time
(slow slew rate)
REV 2.2
Aug 3, 2004
Preliminary
0.60
0.40
0.60
0.40
0.60
2-4, 9,
11, 12
2-4, 9,
11, 12
2-4,
10, 11,
12, 14
20
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
AC Timing Specifications for DDR SDRAM Devices Used on Module
TA = 0 °C ~ 70 °C; VDDQ= VDD= 2.5V ± 0.2V (PC2100/PC2700); VDDQ= VDD= 2.6V ± 0.1V (PC3200) (Part 2 of 2)
Symbol
Parameter
5T
6K
75B
PC3200
PC2700
PC2100
Min.
Max.
Min.
Max.
Min.
Unit
Notes
ns
10-12,
Max.
2-4,
Address and control input setup time
tIS
tIPW
0.7
0.8
1.0
(slow slew rate)
14
2.2
ns
2-4, 12
1.1
tCK
1-4
0.40
0.60
tCK
1-4
45ns
120us
Input pulse width
2.2
2.2
tRP RE
Read preamble
0.9
1.1
0.9
1.1
0.9
tRP ST
Read postamble
0.40
0.60
0.40
0.60
tRAS
Active to Precharge command
42ns
120us
42ns
120us
tRC
Active to Active/Auto-refresh command period
55
60
65
ns
1-4
70
72
75
ns
1-4
Auto-refresh to Active/Auto-refresh command
tRFC
1-4
period
tRCD
Active to Read or Write delay
15
18
20
ns
1-4
tRAP
Active to Read Command with Auto-precharge
15
18
20
ns
1-4
tRP
Precharge command period
15
18
20
ns
1-4
tRRD
Active bank A to Active bank B command
10
12
15
ns
1-4
tWR
Write recovery time
15
(tWR/
tCK ) +
(tRP /
tCK )
1-4
Auto-precharge write recovery + precharge time
15
(tWR/
tCK ) +
(tRP /
tCK )
ns
tDAL
15
(tWR/
tCK ) +
(tRP /
tCK )
tCK
1-4, 13
tWTR
Internal write to read command delay
1
1
1
tCK
1-4
tPDEX
Power down exit time
5
6
7.5
ns
1-4
tXSNR
Exit self-refresh to non-read command
75
75
75
ns
1-4
tXSRD
Exit self-refresh to read command
200
200
200
tCK
1-4
tREFI
Average Periodic Refresh Interval
µs
1-4, 8
REV 2.2
Aug 3, 2004
Preliminary
7.8
7.8
7.8
21
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
AC Timing Specification Notes
1. Input slew rate = 1V/ns.
2. The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross: the input reference level for
signals other than CK/CK is VREF.
3. Inputs are not recognized as valid until VREF stabilizes.
4. The Output timing reference level, as measured at the timing reference point indicated in AC Characteristics (Note 3) is VTT.
5. tHZ and tLZ transitions occur in the same access time windows as valid data transitions. These parameters are not referred to a specific
voltage level, but specify when the device is no longer driving (HZ), or begins driving (LZ).
6. The maximum limit for this parameter is not a device limit. The device operates with a greater value for this parameter, but system
performance (bus turnaround) degrades accordingly.
7. The specific requirement is that DQS be valid (high, low, or some point on a valid transition) on or before this CK edge. A valid transition
is defined as monotonic and meeting the input slew rate specifications of the device. When no writes were previously in progress on the
bus, DQS will be transitioning from Hi-Z to logic LOW. If a previous write was in progress, DQS could be HIGH, LOW, or transitioning from
high to low at this time, depending on tDQSS.
8. A maximum of eight Auto refresh commands can be posted to any given DDR SDRAM device.
9. For command/address input slew rate >= 1.0 V/ns. Slew rate is measured between VOH (AC) and VOL (AC).
10. For command/address input slew rate >= 0.5 V/ns and < 1.0 V/ns. Slew rate is measured between VOH (AC) and VOL (AC).
11. CK/CK slew rates are >= 1.0 V/ns.
12. These parameters guarantee device timing, but they are not necessarily tested on each device, and they may be guaranteed by design
or tester characterization.
13. For each of the terms in parentheses, if not already an integer, round to the next highest integer. tCK is equal to the actual system clock
cycle time. For example, for PC2100 at CL= 2.5, tDAL = (15ns/7.5ns) +(20ns/7.0ns) = 2 + 3 = 5.
14. An input setup and hold time derating table is used to increase tIS and tIH in the case where the input slew rate is below 0.5 V/ns.
1.
2.
Input Slew Rate
Delta (tIS)
Delta (tIH)
Unit
Note
0.5 V/ns
0
0
ps
1, 2
0.4 V/ns
+50
0
ps
1, 2
0.3 V/ns
+100
0
ps
1, 2
Input slew rate is based on the lesser of the slew rates determined by either VIH (AC) to VIL (AC) or VIH (DC) to VIL (DC), similarly for rising
transitions.
These derating parameters may be guaranteed by design or tester characterization and are not necessarily tested on each device.
15. An input setup and hold time derating table is used to increase tDS and tDH in the case where the I/O slew rate is below 0.5 V/ns.
1.
2.
Input Slew Rate
Delta (tDS)
Delta (tDH)
Unit
Note
0.5 V/ns
0
0
ps
1, 2
0.4 V/ns
+75
+75
ps
1, 2
0.3 V/ns
+150
+150
ps
1, 2
I/O slew rate is based on the lesser of the slew rates determined by either VIH (AC) to VIL (AC) or VIH (DC) to VIL (DC), similarly for rising
transitions.
These derating parameters may be guaranteed by design or tester characterization and are not necessarily tested on each device.
16. An I/O Delta Rise, Fall Derating table is used to increase tDS and tDH in the case where DQ, DM, and DQS slew rates differ.
Delta Rise and Fall Rate
1.
2.
3.
4.
Delta (tDS)
Delta (tDH)
Unit
Note
0.0 ns/V
0
0
ps
1-4
0.25 ns/V
+50
+50
ps
1-4
0.5 ns/V
+100
+100
ps
1-4
Input slew rate is based on the lesser of the slew rates determined by either VIH (AC) to VIL (AC) or VIH (DC) to VIL (DC), similarly for rising
transitions.
Input slew rate is based on the larger of AC to AC delta rise, fall rate and DC to DC delta rise, fall rate.
The delta rise, fall rate is calculated as: [1/(slew rate 1)] - [1/(slew rate 2)]
For example: slew rate 1 = 0.5 V/ns; slew rate 2 = 0.4 V/ns. Delta rise, fall = (1/0.5) - (1/0.4) [ns/V] = -0.5 ns/V
Using the table above, this would result in an increase in tDS and tDH of 100 ps.
These derating parameters may be guaranteed by design or tester characterization and are not necessarily tested on each device.
REV 2.2
Aug 3, 2004
Preliminary
22
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Package Dimensions
Non-ECC, 16 TSOP devices
FRONT
133.35
5.250
17.80
0.700
31.75
1.250
10.0
0.394
(2x)4.00
0.157
128.93
5.076
Detail A
2.30
0.91
θ 2.50
0.098
Detail B
Side
BACK
4.00
0.157 MAX
Detail A
1.27+/- 0.10
0.050 +/- 0.004
3.80
0.150
4.00
0.157
Detail B
6.35
0.250
1.00 Width
0.039
1.27 Pitch
0.05
1.80
0.071
Note: All dimensions are typical with tolerances of +/- 0.15 (0.006) unless otherwise stated.
Units: Millimeters (Inches)
REV 2.2
Aug 3, 2004
Preliminary
23
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Package Dimensions
Non-ECC, 8 TSOP devices
FRONT
133.35
5.250
17.80
0.700
31.75
1.250
10.0
0.394
(2x)4.00
0.157
128.93
5.076
Detail A
2.30
0.91
θ 2.50
0.098
Detail B
Side
BACK
Detail A
3.18
0.125 MAX
1.27+/- 0.10
0.050 +/- 0.004
3.80
0.150
4.00
0.157
Detail B
6.35
0.250
1.00 Width
0.039
1.27 Pitch
0.05
1.80
0.071
Note: All dimensions are typical with tolerances of +/- 0.15 (0.006) unless otherwise stated.
Units: Millimeters (Inches)
REV 2.2
Aug 3, 2004
Preliminary
24
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Package Dimensions
Non-ECC, 4 TSOP devices
FRONT
133.35
5.250
17.80
0.700
31.75
1.250
10.00
0.394
(2x)4.00
0.157
128.93
5.076
Detail A
2.30
0.91
θ 2.50
0.098
Detail B
Side
BACK
Detail A
3.18
0.125 MAX
1.27+/- 0.10
0.050 +/- 0.004
3.80
0.150
4.00
0.157
Detail B
6.35
0.250
1.00 Width
0.039
1.27 Pitch
0.05
1.80
0.071
Note: All dimensions are typical with tolerances of +/- 0.15 (0.006) unless otherwise stated.
Units: Millimeters (Inches)
REV 2.2
Aug 3, 2004
Preliminary
25
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Package Dimensions
ECC, 18 TSOP devices
FRONT
133.35
5.25
(2)θ
2.50
0.098
Detail A
2.30
0.091
17.80
0.700
31.75
1.250
10.0
0.394
(2x)4.00
0.157
128.95
5.077
Detail B
Side
BACK
Detail A
4.00
0.157 max.
1.27+/- 0.10
0.050 +/- 0.004
3.80
0.150
4.00
0.157
Detail B
6.35
0.250
1.00 Width
0.039
1.27 Pitch
0.05
1.80
0.071
Note: All dimensions are typical with tolerances of +/- 0.15 (0.006) unless otherwise stated.
Units: Millimeters (Inches)
REV 2.2
Aug 3, 2004
Preliminary
26
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Package Dimensions
ECC, 9 TSOP devices
FRONT
133.35
5.25
(2)θ
2.50
0.098
Detail A
2.30
0.091
17.80
0.700
31.75
1.250
10.0
0.394
(2x)4.00
0.157
128.95
5.077
Detail B
Side
BACK
Detail A
2.59
0.157 max.
1.27+/- 0.10
0.050 +/- 0.004
3.80
0.150
4.00
0.157
Detail B
6.35
0.250
1.00 Width
0.039
1.27 Pitch
0.05
1.80
0.071
Note: All dimensions are typical with tolerances of +/- 0.15 (0.006) unless otherwise stated.
Units: Millimeters (Inches)
REV 2.2
Aug 3, 2004
Preliminary
27
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.
NT512D64S8HB1G / NT512D64S8HB1GY / NT512D64S8HB0G
NT256D64S88B1G / NT256D64S88B1GY NT256D64S88B0G
NT128D64SH4B1G / NT512D72S8PB0G (ECC) / NT256D72S89B0G (ECC)
Unbuffered DDR DIMM
Revision Log
Rev
Date
0.1
12/2003
1.0
Dec 19,2003
Modification
Updated format.
Release
Correction to block diagram label.
1.1
Feb 11, 2004
Correction to SPD bank and checksum values.
Package dimension added for x8 wide devices.
Document reorganized by order of B die generation / size and DIMM format.
DIMM: unbuffered DIMM
Speed grades: 5T, 6K, 75B
2.0
Mar 4, 2004
Modules: NT512D64S8HB1G, NT256D64S88B1G, NT128D64SH4B1G
Modules: NT512D72S8PB0G, NT256D72S89B0G
Modules: NT512D64S8HB1GY, NT256D64S88B1GY
2.1
May 11, 2004
Added NT256D64S88B0G-6K speed grade to ordering information.
2.2
Aug 3, 2004
Corrected SPD contents.
Nanya Technology Corporation
Hwa Ya Technology Park 669
Fu Hsing 3rd Rd., Kueishan,
Taoyuan, 333, Taiwan, R.O.C.
Tel: +886-3-328-1688
Please visit our home page for more information: www.nanya.com
Nanya reserves the right to make changes or deletions without any notice to any of its products. Nanya makes no guarantee, warranty or representation regarding the suitability of
its products for any particular purpose. Nanya assumes no liability arising out of the application or use of its products. All parameters can and do vary in its application and must
be validated for each customer application by the customer’s technician. By purchasing Nanya products, Nanya does not convey any license under its patent rights not the rights
of others. Nanya products are not designed or intended or authorized for use in systems intended for the military or surgical implants or any other applications where life is involved
or where injury or death may occur or the loss/corruption of data or the loss of system reliability or mission critical applications. Should the buyer purchase or use Nanya products
in such unintended or unauthorized application, the Buyer and user shall indemnify and hold Nanya and its officers, employees, subsidiaries, affiliates and distributors harmless
against all claims, costs, damages, all fees and expenses directly or indirectly arising from any claim of loss, injury or death associated with unintended or unauthorized use even
if such claims alleges Nanya was negligent regarding design or manufacture of the part. Nanya and the Nanya logo are trademarks of the Nanya Technology Corporation.
Printed in Taiwan
©2004
REV 2.2
Aug 3, 2004
Preliminary
28
© NANYA TECHNOLOGY CORPORATION
NANYA reserves the right to change products and specifications without notice.