TI UCC3626PW

 SLUS318B – APRIL 1999 – REVISED JANUARY 2002
FEATURES
D Two-Quadrant and Four-Quadrant Operation
D Integrated Absolute Value Current Amplifier
D Pulse-by-Pulse and Average Current Sensing
D Accurate, Variable Duty-Cycle Tachometer
Output
D Trimmed Precision Reference
D Precision Oscillator
D Direction Output
DESCRIPTION
The UCC3626 motor controller device combines
many of the functions required to design a
high-performance, two- or four-quadrant, threephase, brushless dc motor controller into one
package. Rotor position inputs are decoded to
provide six outputs that control an external power
stage. A precision triangle oscillator and latched
comparator provide PWM motor control in either
voltage- or current-mode configurations. The
oscillator is easily synchronized to an external
master clock source via the SYNCH input.
Additionally, a QUAD select input configures the
chip to modulate either the low-side switches only,
or both upper and lower switches, allowing the
user to minimize switching losses in less
demanding two-quadrant applications.
The device includes a differential current-sense
amplifier and absolute-value circuit which provide
an accurate reconstruction of motor current,
useful for pulse-by-pulse overcurrent protection,
as well as closing a current control loop. A
precision tachometer is also provided for
implementing closed-loop speed control. The
TACH_OUT signal is a variable duty-cycle,
frequency output, which can be used directly for
digital control or filtered to provide an analog
feedback signal. Other features include COAST,
BRAKE, and DIR_IN commands, along with a
direction output, DIR_OUT.
Copyright  2002, Texas Instruments Incorporated
! " #$ %!&
% "! "! '! ! !( !
%% )*& % "!+ %! !!$* $ %!
!+ $$ "!!&
www.ti.com
1
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
AVAILABLE OPTIONS
TA
PDIP
(N)
PACKAGED DEVICES
SOIC{
(DW)
TSSOP{
(PW)
–40_C to 85_C
UCC2626N
UCC2626DW
UCC2626PW
0_C to 70_C
UCC3626N
UCC3626DW
UCC3626PW
{The DW and PW packages are available taped and reeled. Add TR suffix to device
type (e.g. UCC2626DWTR) to order quantities of 2,000 devices per reel.
N PACKAGE
(TOP VIEW)
GND
VREF
TACH_OUT
R_TACH
C_TACH
CT
SYNCH
DIR_OUT
SNS_NI
SNS_I
IOUT
OC_REF
PWM_I
PWM_NI
1
28
2
27
3
26
4
25
5
24
6
23
7
22
8
21
9
20
10
19
11
18
12
17
13
16
14
15
DW and PW PACKAGES
(TOP VIEW)
VDD
AHI
ALOW
BHI
BLOW
CHI
CLOW
DIR_IN
QUAD
BRAKE
COAST
HALLC
HALLB
HALLA
GND
VREF
TACH_OUT
R_TACH
C_TACH
CT
SYNCH
DIR_OUT
SNS_NI
SNS_I
IOUT
OC_REF
PWM_I
PWM_NI
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VDD
AHI
ALOW
BHI
BLOW
CHI
CLOW
DIR_IN
QUAD
BRAKE
COAST
HALLC
HALLB
HALLA
absolute maximum ratings over operating free-air temperature (unless otherwise noted)†
Supply voltage VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 V
Input voltage, BRAKE, COAST, DIR_IN, HALLA, HALLB, HALLC,
OC_REF, QUAD, SYNCH, PWM_I, PWM_NI . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD
SNS_I, SNS_NI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VDD
Output current AHI, ALOW, BHI, BLOW, CHI, CLOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±200 mA
DIR_OUT, IOUT, TACH_OUT, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 mA
VREF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –20 mA
Junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡ All voltages are with respect to GND. Currents are positive into negative out of the specified terminal.
2
www.ti.com
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
block diagram
28
VDD
2
VREF
27
AHI
25
BHI
23
CHI
26
ALOW
24
BLOW
QUAD 20
5 VOLT
REFERENCE
BRAKE 19
COAST 18
1.75V
DIR_IN 21
DIRECTION
SELECT
HALLA 15
HALLB 16
HALL
DECODER
HALLC 17
DIR_OUT 8
DIRECTION
DETECTOR
EDGE
DETECTOR
PWM_NI 14
22 CLOW
PWM_I 13
PWM
COMPARATOR
OSCILLATOR
RxC
SYNCH 7
CT
6
OC_REF 12
IOUT 11
SNS_NI
OVERCURRENT
COMPARATOR
S
Q
R
Q
S
SENSE AMPLIFIER
R
9
SNS_I 10
Q
ONE
SHOT
Q
3
TACH_OUT
5
C_TACH
4
R_TACH
1
GND
PWM LOGIC
X5
UDG–97173
www.ti.com
3
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
electrical characteristics over recommended operating conditions, VCC = 12 V; CT = 1 nF,
R_TACH = 250 kΩ, C_TACH = 100 pF, TA = TJ, TA = –40°C to 85°C for the UCC2626, and 0°C to 70°C
for the UCC3626 (unless otherwise noted)
overall
PARAMETER
TEST CONDITIONS
Supply current
Outputs not switching
MIN
TYP
MAX
UNIT
1
3
5
MIN
TYP
MAX
UNIT
mA
undervoltage lockout
PARAMETER
TEST CONDITIONS
Start threshold
UVLO hysteresis
9.0
10.5
11.0
V
0.35
0.40
0.50
V
MIN
TYP
MAX
UNIT
4.9
5
5.1
V
10
mV
10
mV
5-V reference
PARAMETER
TEST CONDITIONS
Output voltage
Line regulation voltage
IVREF = –2 mA
11 V < VCC < 14.5 V
Load regulation voltage
–1 mA > IVREF > –5 mA
Short circuit current
40
120
240
mA
coast input comparator
MIN
TYP
MAX
UNIT
Threshold voltage
PARAMETER
TEST CONDITIONS
1.60
1.75
2.00
V
Hysteresis
0.04
0.10
0.16
V
MIN
TYP
MAX
UNIT
current sense amplifier
PARAMETER
TEST CONDITIONS
Input offset voltage
VCM = 0 V
Input bias current
VCM = 0 V
5
10
15
µA
Gain
VCM = 0 V
4.85
5.00
5.15
V/V
PSRR
11 V < VCC < 14.5 V
60
dB
High-level output voltage
IIOUT= –100 µA
IIOUT = 100 µA
6.3
V
VIOUT = 2 V
VIOUT = 2 V
500
µA
300
µA
Low-level output voltage
UCC3626
Output source current
UCC2626
8
70
mV
mV
pwm comparator
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Input common mode range
2.0
8.0
V
Propagation delay time
75
150
ns
MAX
UNIT
overcurrent comparator
PARAMETER
TEST CONDITIONS
MIN
Input common mode range
0.0
Propagation delay time
50
MIN
TYP
5.0
V
175
250
ns
TYP
MAX
UNIT
logic inputs
PARAMETER
TEST CONDITIONS
High-level logic input voltage
QUAD, BRAKE, DIR, SYNCH
Low-level logic input voltage
QUAD, BRAKE, DIR, SYNCH
4
www.ti.com
3.6
V
1.4
V
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
electrical characteristics over recommended operating conditions, VCC = 12 V; CT = 1 nF,
R_TACH = 250 kΩ, C_TACH = 100 pF, TA = TJ, TA = –40°C to 85°C for the UCC2626, and 0°C to 70°C
for the UCC3626 (unless otherwise noted)
hall buffer inputs
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
1.9
2.1
High-level input voltage
HALLA, HALLB, HALLC
1.7
Hysteresis
HALLA, HALLB, HALLC
0.6
Input current
0V < VIN < 5 V
1.0
UNIT
V
V
µA
–25
oscillator
PARAMETER
TEST CONDITIONS
Frequency
RTACH = 250 kΩ, CT = 1nF
12 V < VCC < 14.5 V
Frequency change with voltage
MIN
TYP
MAX
UNIT
9.0
10.0
11.0
kHz
3%
CT peak voltage
7.25
7.5
7.75
CT peak-to-valley voltage
4.75
5.0
5.25
SYNCH pin minimum pulse width
500
V
V
ns
tachometer
PARAMETER
TEST CONDITIONS
IOUT = –10 µA
IOUT = 10 µA
High-level output voltage/VREF
Low-level output voltage
MIN
Low-level on-resistance
High-level ramp threshold voltage
CTACH charge current
UNIT
20
mV
1
1.5
kΩ
1
1.5
kΩ
2.5
Ramp voltage
On time accuracy
On-time
MAX
100%
0
IOUT = –100 µA
IOUT = 100 µA
High-level on-resistance
TYP
99%
2.375
2.500
48
51
V
2.625
V
53
µA
UCC3626
RTACH = 49.9 kΩ
See Note 1
–3%
3%
UCC2626
See Note 1
–4%
3%
direction output
PARAMETER
TEST CONDITIONS
IOUT = –100 µA
IOUT = 100 µA
High-level output voltage
Low-level output voltage
MIN
TYP
MAX
UNIT
4.5
5.2
V
0
0.5
V
output
PARAMETER
TEST CONDITIONS
MIN
TYP
Maximum duty cycle
IOUT = 2 mA
IOUT = 100 µA
0.0
Lo le el o
Low-level
output
tp t voltage
oltage
IOUT = –2 mA
IOUT = –100 µA
4.0
High level output voltage
High-level
Rise and fall time
CI = 10 pF
NOTE 1: tON is calculated using the formula t ON +
MAX
UNIT
100%
C TACH
0.1
0.0
4.7
4.8
0.5
V
0.1
V
5.2
V
5.2
V
100
ns
ǒV HI * V LOǓ
I CHARGE
www.ti.com
5
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
pin descriptions
AHI, BHI, CHI: Digital outputs used to control the high-side switches in a three-phase inverter. For specific
decoding information reference Table I.
ALOW, BLOW, CLOW: Digital outputs used to control the low-side switches in a three-phase inverter. For
specific decoding information reference Table I.
BRAKE: BRAKE is a digital input which causes the device to enter brake mode. In brake mode all three highside outputs (AHI, BHI & CHI) are turned off, while all three lowside outputs (ALOW, BLOW, CLOW) are turned
on. During brake mode the tachometer output remains operational. The only conditions that can inhibit the
low-side commands during brake are UVLO, exceeding peak current, the output of the PWM comparator, or
the COAST command.
COAST: The COAST input consists of a hysteretic comparator which disables the outputs. The input is useful
in implementing an overvoltage bus clamp in four-quadrant applications. The outputs are disabled when the
input is above 1.75 V.
CT: This pin is used in conjunction with the R_TACH pin to set the frequency of the oscillator. A timing capacitor
is normally connected between this point and ground and is alternately charged and discharged between 2.5 V
and 7.5 V.
C_TACH: A timing capacitor is connected between this pin and ground to set the width of the TACH_OUT pulse.
The capacitor is charged with a current set by the resistor on pin R_TACH .
DIR_IN: DIR_IN is a digital input which determines the order in which the HALLA, HALLB, and HALLC inputs
are decoded. For specific decode information reference Table I.
DIR_OUT: DIR_OUT represents the actual direction of the rotor as decoded from the HALLA, HALLB, and
HALLC inputs. For any valid combination of HALLA, HALLB, and HALLC inputs there are two valid transitions;
one of which translates to a clockwise rotation and another which translates to a counterclockwise rotation. The
polarity of DIR_OUT is the same as DIR_IN while motoring, (i.e. sequencing from top to bottom in Table 1.)
GND: GND is the reference ground for all functions of the part. Bypass and timing capacitors should be
terminated as close as possible to this point.
HALLA, HALLB, HALLC: These three inputs are designed to accept rotor position information positioned 120°
apart. For specific decode information reference Table I. These inputs should be externally pulled up to VREF
or another appropriate external supply.
IOUT: IOUT represents the output of the current sense and absolute value amplifiers. The output signal
appearing is a representation of the following expression:
ǒ
Ǔ
I OUT + ABS I SNS_I * I SNS_NI
5
This output can be used to close a current control loop as well as provide additional filtering of the current sense
signal.
OC_REF: OC_REF is an analog input which sets the trip voltage of the overcurrent comparator. The sense input
of the comparator is internally connected to the output of the current sense amplifier and absolute value circuit.
PWM_NI: PWM_NI is the noninverting input to the PWM comparator.
PWM_I: PWM_I is the inverting input to the PWM comparator.
QUAD: The QUAD input selects between two-quadrant operation (QUAD = 0) and four-quadrant operation
(QUAD = 1) . When in two-quadrant mode, only the low-side devices are effected by the output of the PWM
comparator. In four-quadrant mode both high- and low-side devices are controlled by the PWM comparator.
6
www.ti.com
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
pin descriptions
SYNCH: The SYNCH input is used to synchronize the PWM oscillator with an external digital clock. When using
the SYNCH feature, a resistor equal to R_TACH must be placed in parallel with CT. When not using the SYNCH
feature, SYNCH must be grounded.
SNS_NI, SNS_I: These inputs are the noninverting and inverting inputs to the current sense amplifier,
respectively. The integrated amplifier is configured for a gain of five. An absolute value function is also
incorporated into the output in order to provide a representation of actual motor current when operating in
four-quadrant mode.
TACH_OUT: TACH_OUT is the output of a monostable triggered by a change in the commutation state, thus
providing a variable duty cycle, frequency output. The on time of the monostable is set by the timing capacitor
connected to C_TACH. The monostable is capable of being retriggered if a commutation occurs during its
on-time.
R_TACH: A resistor connected between R_TACH and ground programs the current for both the oscillator and
tachometer.
VDD: VDD is the input supply connection for this device. Undervoltage lockout keeps the outputs off for inputs
below 10.5 V. The input should be bypassed with a 0.1-µF ceramic capacitor, minimum.
VREF: VREF is a 5-V, 2% trimmed reference output with 5 mA of maximum available output current. This pin
should be bypassed to ground with a ceramic capacitor with a value of at least 0.1 µF.
APPLICATION INFORMATION
Table 1 provides the decode logic for the six outputs, AHI, BHI, CHI, ALOW, BLOW, and CLOW as a function
of the BRAKE, COAST, DIR_IN, HALLA, HALLB, and HALLC inputs.
Table 1. Commutation Truth Table
HALL
INPUTS
HIGH-SIDE
OUTPUTS
LOW-SIDE
OUTPUTS
C
A
B
C
A
B
C
1
1
0
0
0
1
0
0
0
1
0
0
0
0
1
1
1
0
0
1
0
0
0
1
1
0
1
0
0
1
0
1
0
0
1
0
1
1
0
0
1
1
0
0
0
1
0
0
1
0
0
1
0
1
0
0
0
0
1
0
1
0
1
0
1
0
0
0
0
0
0
0
1
0
1
0
0
0
1
0
0
0
0
1
1
1
0
0
0
0
1
0
0
0
0
1
0
1
0
0
0
1
0
0
0
0
1
1
0
0
0
1
0
1
0
0
0
0
1
0
0
0
0
1
1
0
0
X
1
X
X
X
X
0
0
0
0
0
0
1
0
X
X
X
X
0
0
0
1
1
1
0
0
X
1
1
1
0
0
0
0
0
0
0
0
X
0
0
0
0
0
0
0
0
0
BRAKE
COAST
DIR_IN
A
B
0
0
1
1
0
0
0
1
1
0
0
1
0
0
0
0
0
www.ti.com
7
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
The UCC3626 is designed to operate with 120° position sensor encoding. In this format, the three position
sensor signals are never simultaneously high or low. Motors whose sensors provide 60° encoding, can be
converted to 120° using the circuit shown in Figure 1.
In order to prevent noise from commanding improper commutation states, some form of low-pass filtering on
HALLA, HALLB, and HALLC is recommended. Passive RC networks generally work well and should be located
as close as possible to the device. Figure 2 illustrates these techniques.
VREF
VREF
1 kΩ
499 Ω
1 kΩ
HALLB
HALLA
499 Ω
HALLA
HALLA
2.2 nF
2.2 nF
VREF
1 kΩ
VREF
HALLA
1 kΩ
1 kΩ
499 Ω
HALLB
2N2222A
HALLB
HALLB
2.2 nF
2.2 nF
VREF
1 kΩ
VREF
499 Ω
1 kΩ
HALLC
HALLC
HALLC
HALLC
2.2 nF
2.2 nF
UDG–97182
Figure 1. Converting Hall Code From 60° to 120°
8
499 Ω
www.ti.com
UDG–97185
Figure 2. Passive Hall Filtering Technique
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
configuring the oscillator
The UCC3626 oscillator is designed to operate at frequencies up to 250 kHz and provide a triangle waveform
on CT with a peak-to-peak amplitude of 5 V for improved noise immunity. The current used to program CT is
derived from the R_TACH resistor according to the following equation:
I OSC +
25
Amps
R_TACH
(1)
The oscillator frequency is set by R_TACH and CT according to the following relationship:
f OSC +
2.5
R_TACH
CT
Hz
(2)
Timing resistor values should be between 25 kΩ and 500 kΩ, while capacitor values should be between 100 pF
and 1 µF. Figure 3 provides a graph of oscillator frequency for various combinations of timing components. As
with any high-frequency oscillator, timing components should be located as close as possible to the device pins
when laying out the printed-circuit board. It is also important to reference the timing capacitor directly to the
ground pin on the UCC3626 rather than daisy chaining it to another trace or the ground plane. This technique
prevents switching current spikes in the local ground from causing jitter in the oscillator.
synchronizing the oscillator
A common system specification is to have all oscillators synchronized to a master clock. The UCC3626 provides
a SYNCH input for this purpose. The SYNCH input is designed to interface with a digital clock pulse generated
by the master oscillator. A positive-going edge on this input causes the UCC3626 oscillator to begin discharging.
In order for the slave oscillator to function properly, it must be programmed for a frequency slightly lower than
that of the master. Also, a resistor equal to R_TACH must be placed in parallel with CT. Figure 4 illustrates the
waveforms for a slave oscillator programmed to 20 kHz with a master frequency of 30 kHz. The SYNCH pin
must be grounded when not used.
1.E+06
OSCILLATOR FREQUENCY
vs
TIMING CAPACITANCE
fOSC – PWM Frequency – Hz
R_TACH = 25 kΩ
R_TACH = 100 kΩ
1.E+05
1.E+04
R_TACH = 250 kΩ
R_TACH = 500 kΩ
1.E+03
1.E–09
1.E–07
1.E–08
1.E–10
CT – Oscillator Timing Capacitance – F
Figure 3
www.ti.com
9
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
programming the tachometer
The UCC3626 tachometer consists of a precision 5-V monostable, triggered by either a rising or falling edge
on any of the three Hall inputs, HALLA, HALLB, and HALLC. The resulting TACH_OUT waveform is a variable
duty-cycle square wave whose frequency is proportional to motor speed, as given by:
TACH_OUT + V
20
P Hz
(3)
where P is the number of motor pole pairs and V is motor velocity in RPM.
The on time of the monostable is programmed via timing resistor R_TACH and capacitor C_TACH according
to the following equation:
t ON + R_TACH
C_TACH sec
(4)
Figure 5 provides a graph of on times for various combinations of R_TACH and C_TACH. On time is typically
set to a value less than the minimum TACH_OUT period as given by:
t PERIOD (min) +
20
V MAX
P
sec
(5)
where P is the number of motor pole pairs and V is motor velocity in RPM.
TACHOMETER ON-TIME
vs
TIMING CAPACITANCE
SYNCH
WITHOUT SYNCH
tON – Tachometer On–Time – s
1.E+00
R_TACH = 500 kΩ
1.E–01
1.E–02
R_TACH = 250 kΩ
1.E–03
R_TACH = 100 kΩ
1.E–04
1.E–05
CT
WITH SYNCH
R_TACH = 25 kΩ
1.E–06
1.E–10
1.E–09
1.E–08
1.E–07
1.E–06
C_TACH – Tachometer Timing Capacitance – F
Figure 4. Oscillator Waveforms
10
Figure 5
www.ti.com
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
The TACH_OUT signal can be used to close a digital velocity loop using a microcontroller, as shown in Figure 6,
or directly low-pass filtered in an analog implementation, Figure 7.
UCC3626
MC68HC11
AD558
PB0–PB7
DB0–DB7
PC0
VCE
4
R_TACH
5
C_TACH
6
CT
14 PWM_NI
VCS
VOUT
13 PWM_I
VOUTSENSE
VOUTSELECT
IC1
3
TACH_OUT
UDG–97188
Figure 6. Digital Velocity Loop Implementation Using MC68HC11
two quadrant vs four quadrant control
Figure 8 illustrates the four possible quadrants of operation for a motor. Two-quadrant control refers to a system
in which operation is limited to quadrants I and III (where torque and velocity are in the same direction). With
a two-quadrant brushless dc amplifier, there are no provisions other than friction to decelerate the load, limiting
the approach to less demanding applications. Four-quadrant controllers, on the other hand, provide controlled
operation in all quadrants, including II and IV, where torque and rotation are of opposite direction.
UCC3626
2
VREF
4
R_TACH
5
C_TACH
6
CT
VELOCITY
CW
II
I
III
IV
CCW
14
–
TORQUE
CW
PWM_NI
13
PWM_I
3
TACH_OUT
+
CCW
UDG–97189
UDG–01118
Figure 8. Four Quadrants of Operation
Figure 7. Simple Analog Velocity Loop
www.ti.com
11
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
When configured for two-quadrant operation, (QUAD=0), the UCC3626 modulates only the low-side devices
of the output power stage. The current paths within the output stage during the PWM on- and off-times are
illustrated in Figure 9. During the on interval, both switches are on, and current flows through the load down to
ground. During the off time, the lower switch is shut off, and the motor current circulates through the upper half
bridge via the flyback diode. The motor is assumed to be operating in either quadrant I or III.
If operation is attempted in quadrants II or IV by changing the DIR bit and reversing the torque, switches 1 and
4 are turned off and switches 2 and 3 turned on. Under this condition motor current very quickly decays, reverses
direction and increases until the control threshold is reached. At this point, switch 2 turns off and current once
again circulates in the upper half bridge. However, in this case, the motor’s BEMF is in phase with the current,
(i.e. the motor’s direction of rotation has not yet changed.) Figure 10 illustrates the current paths when operating
in this mode. Under these conditions there is nothing to limit the current other than motor and drive impedance.
These high-circulating currents can result in damage to the power devices in addition to high, uncontrolled
torque.
VMOT
VMOT
S3
S1
S3
S1
S5
S5
IOFF
IOFF
IPHASE
IPHASE
+ BEMF –
+ BEMF –
ION
ION
S2
S4
S2
S6
UDG–01119
S6
UDG–01120
Figure 10. Two-Quadrant Reversal
Figure 9. Two-Quadrant Chopping
12
S4
www.ti.com
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
By pulse width modulating both the upper and lower power devices (QUAD=1), motor current always decays
during the PWM off time, eliminating any uncontrolled circulating currents. In addition, current always flows
through the current sense resistor, providing a suitable feedback signal. Figure 11 illustrates the current paths
during a four-quadrant torque reversal. Motor drive waveforms for both two- and four-quadrant operation are
illustrated in Figure 12.
VMOT
S3
S1
S5
IPHASE
+ BEMF –
IOFF
ION
S2
S4
S6
UDG–01121
Figure 11. Four-Quadrant Reversal
www.ti.com
13
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
ROTOR POSITION IN ELECTRICAL DEGREES
0
60
120
180
240
300
360
420
480
540
600
660
720
H1
SENSOR
INPUTS H2
H3
Code
101
100
110
010
011
001
101
100
110
010
011
001
HIGH SIDE AHI
OUTPUTS
QUAD=0 BHI
CHI
ALO
LOW SIDE
OUTPUTS BLO
QUAD=0
CLO
+
A
0
–
MOTOR
PHASE
CURRENTSB
QUAD=0
+
0
–
+
C
0
–
HIGH SIDE AHI
OUTPUTS
QUAD=1 BHI
CHI
ALO
LOW SIDE
OUTPUTS BLO
QUAD=1
CLO
+
A
0
–
MOTOR
PHASE
CURRENTSB
QUAD=1
+
0
–
+
C
0
–
100% Duty Cycle PWM
50% Duty Cycle PWM
Figure 12. Motor Drive and Current Waveforms for Two-Quadrant (QUAD=0)
and Four-Quadrant (QUAD=1) Operation
14
www.ti.com
UDG–97190
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
power stage design considerations
The flexible architecture of the UCC3626 requires the user to pay close attention to the design of the power
output stage. Two- and four-quadrant applications not requiring the brake function are able to use the power
stage approach illustrated in Figure 13a. In many cases the body diode of the MOSFET can be used to reduce
parts count and cost. If efficiency is a key requirement, Schottky diodes can be used in parallel with the switches.
UDG–97190
VMOT
VMOT
CURRENT
SENSE
VMOT
TO
TO
MOTOR
MOTOR
CURRENT
SENSE
TO
MOT
CURRENT
SENSE
(a)
(b)
(c)
UDG–01122
CURRENT SENSE
TWO
QUADRANT
FOUR
QUADRANT
SAFE
BRAKING
POWER
REVERSAL
(a)
YES
(b)
YES
YES
NO
NO
YES
(c)
YES
YES
YES
PULSE-BYPULSE
AVERAGE
Four-Quad Only
YES
YES
No
YES
NO
Four-Quad Only
YES
YES
Figure 13. Power Stage Topologies
If the system requires a braking function, diodes must be added in series with the lower power devices and the
lower flyback diodes must be returned to ground, as pictured in Figure 13b, and 13c. This requirement prevents
brake currents from circulating in the lower half bridge and bypassing the sense resistor. In addition, the
combination of braking and four-quadrant control necessitates an additional resistor in the diode path to sense
current during the PWM off time as illustrated in Figure 13c.
www.ti.com
15
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
current sensing
The UCC3626 includes a differential current-sense amplifier with a fixed gain of five, along with an absolute
value circuit. The current-sense signal should be low pass filtered to eliminate leading-edge spikes. In order to
maximize performance, the input impedance of the amplifier should be balanced. If the sense voltage must be
trimmed for accuracy reasons, a low-value input divider or a differential divider should be used to maintain
impedance matching, as shown in Figure 14.
RF
RF
SNS_NI
RADJ
RADJ
RS
SNS_NI
RF
CF
RS
CF
RF
RF
SNS_I
SNS_I
RADJ << RF
(a)
(b)
UDG–01123
Figure 14. (a) Differential Divider and (b) Low-Value Divider
With four-quadrant chopping, motor current always flows through the sense resistor. However, during the
flyback period the polarity across the sense resistor is reversed. The absolute value amplifier cancels the
polarity reversal by inverting the negative sense signal during the flyback time, see Figure 15. Therefore, the
output of the absolute value amplifier is a reconstructed analog of the motor current, suitable for protection as
well as feedback loop closure.
VMOT
Ip
S3
S1
Is
S5
IPHASE
Ip
If
+ BEMF –
IOFF
5*Ip
ION
S2
S4
S6
Im
Is
X5
Im
UDG–01124
If
Figure 15. Current Sense Amplifier Waveform
16
www.ti.com
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
Figure 17 illustrates a simple 175-V, 2-A, two-quadrant velocity controller using the UCC3626. The power stage
is designed to operate with a rectified off-line supply using IR2210s to provide the interface between the low
voltage control signals and the power MOSFETs. The power topology illustrated in Figure 13c is implemented
in order to provide braking capability.
SIGN/MAGNITUDE CONVERTER
10 kΩ
VELOCITY
COMMAND
±5V
–
U1
+
10 kΩ
10 kΩ
–
U5
+
–
U6
+
10 kΩ
11
IOUT
13
PWM_I
21
DIR
10 kΩ
–
U8
+
CURRENT
ERROR
AMPLIFIER
CURRENT
MAGNITUDE
U7
CURRENT SIGN
BIPOLAR
10 kΩ TACH GAIN
–
U3
+
4.99 kΩ
10 kΩ
4.99 kΩ
–
U2
+
TACHOMETER
FILTER
3
TACH_OUT
8
DIR_OUT
2N7002
UDG–99061
Figure 16. Four-Quadrant Control Loop
The controller’s speed command is set by potentiometer R30, while the speed feedback signal is obtained by
low-pass filtering and buffering the TACH_OUT signal using R11 and C9. Small signal compensation of the
velocity control loop is provided by amplifier U5A, whose output is used to control the PWM duty cycle. The
integrating capacitor, C8, places a pole at 0 Hz and a zero in conjunction with R10. This zero can be used to
cancel the low-frequency motor pole and to cross the loop-over with a –20 dB gain response.
Four-quadrant applications require the control of motor current. Figure 16 illustrates a sign/magnitude current
control loop within an outer bipolar velocity loop using the UCC3626. U1 serves as the velocity loop error
amplifier and accepts a ± 5-V command signal. Velocity feedback is provided by low-pass filtering and scaling
the TACH_OUT signal using U2. The direction output switch, DIR_OUT, and U3 set the polarity of the
tachometer gain according to the direction of rotation. The output of the velocity error amplifier, U1, is then
converted to sign/magnitude form using U5 and U6. The sign portion is used to drive the DIR input while the
magnitude commands the current error amplifier, U8. Current feedback is provided by the internal current sense
amplifier via the IOUT pin.
www.ti.com
17
FROM
HALL
SENSORS
18
R6
499 Ω
www.ti.com
+
R10
C8
R9
10 kΩ
R29
U5A
1/2 LM358
C7
C6
100 pF
R8
10 kΩ
C3
2200 pF
+
C9
0.1 µF
R11
160 kΩ
8
DIR_OUT
13 PWM_I
3
14 PWN_IN TACH_OUT
IOUT 11
5
4
CT
SYNCH
CTACH
RTACH
6
7
18 COAST
OC_REF 12
9
19 BRAKE
SNS_NI
SNS_I 10
QUAD
CLOW 22
21 DIR_IN
20
17 HALLC
BLOW 24
16 HALLB
CHI 23
BHI 25
AHI 27
ALOW 26
GND
VREF
UCC3626
15 HALLA
1
2
28 VDD
U5B
1/2 LM358
C1
0.1 µF
VREF
C2
0.1 µF
+12V
C4
2200 pF
499 Ω
R4
R3
1 kΩ
SPEED SET
R7
10 kΩ
C5
2200 pF
VREF
499 Ω
R5
R2
1 kΩ
VREF
R30
10 kΩ
R1
1 kΩ
VREF
U1
Figure 17. Two-Quadrant Velocity Controller
R14
15 k Ω
R13
35 kΩ
VREF
R12
250 kΩ
C10
3900 pF
C14
0.1 µF
C17
0.1 µF
VREF
VREF
C11
0.1 µF
VREF
NC
VDD
NC
VDD
NC
VDD
C23
0.1 µF
LO
COM
14 NC
13 VSS
VCC
NC
VS
HO
VB
11 SD
12 LIN
10 HIN
8
9
U3
LO
COM
VCC
NC
VS
HO
VB
LO
COM
IR2110
13 VSS
14 NC
11 SD
12 LIN
10 HIN
8
9
U3
NC
VS
HO
VB
VCC
IR2110
13 VSS
14 NC
11 SD
12 LIN
10 HIN
8
9
U2
IR2110
1
2
3
4
5
7
6
1
2
3
4
5
7
6
1
2
3
4
5
7
6
R31 2 k Ω
+12V
R18
47 Ω
R25
D6
10 Ω 1N4148
D18
11DF4
C18
0.1 µF
Q4
IRF730
D10
MUR1520
Q3
IRF730
R27
0.1 Ω
Q2
IRF730
D13
MUR1520
Q5
IRF730
D5
1N4148 VMOT
R24
47 Ω
R23
10 Ω
R22
47 Ω
R21
D4
10 Ω 1N4148
+12V
R20
47 Ω
D17
11DF4
Q2
IRF730
D7
MUR1520
D3
1N4148 VMOT
R18
47 Ω
R19
10 Ω
C15
0.1 µF
R30 2 k Ω
C19
0.1 µF
C16
0.1 µF
C13
0.1 µF
+12V
R17
D2
10 Ω 1N4148
D16
11DF4
C12
0.1 µF
Q1
IRF730
D1
1N4148 VMOT
R16
47 Ω
R15
10 Ω
R28
0.1 Ω
D15
1N5418
MOTOR
PHASE C
C20
10 µF
D11
1N5418
MOTOR
PHASE B
C21
10 µF
D8
1N5418
MOTOR
PHASE A
C22
10 µF
SLUS318B – APRIL 1999 – REVISED JANUARY 2002
APPLICATION INFORMATION
UDG–01117
PACKAGE OPTION ADDENDUM
www.ti.com
28-Aug-2010
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
UCC2626DW
ACTIVE
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
UCC2626DWG4
ACTIVE
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
UCC2626PW
ACTIVE
TSSOP
PW
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
UCC2626PWG4
ACTIVE
TSSOP
PW
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
UCC3626DW
ACTIVE
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
UCC3626DWG4
ACTIVE
SOIC
DW
28
20
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
UCC3626DWTR
ACTIVE
SOIC
DW
28
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
UCC3626DWTRG4
ACTIVE
SOIC
DW
28
1000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
UCC3626N
ACTIVE
PDIP
N
28
13
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
Purchase Samples
UCC3626NG4
ACTIVE
PDIP
N
28
13
Green (RoHS
& no Sb/Br)
CU NIPDAU N / A for Pkg Type
Purchase Samples
UCC3626PW
ACTIVE
TSSOP
PW
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
UCC3626PWG4
ACTIVE
TSSOP
PW
28
50
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
28-Aug-2010
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
UCC3626DWTR
Package Package Pins
Type Drawing
SOIC
DW
28
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
1000
330.0
32.4
Pack Materials-Page 1
11.35
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
18.67
3.1
16.0
32.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
UCC3626DWTR
SOIC
DW
28
1000
367.0
367.0
55.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated