TI TLV2545

TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
D Maximum Throughput . . . 140/200 KSPS
D Built-In Conversion Clock
D INL/DNL: ±1 LSB Max, SINAD: 72 dB,
D
D
D
D
SFDR: 85 dB, fi = 20 kHz
SPI/DSP-Compatible Serial Interface
Single Supply: 2.7 Vdc to 5.5 Vdc
Rail-to-Rail Analog Input With 500 kHz BW
Three Options Available:
− TLV2541: Single Channel Input
TOP VIEW
TLV2541
CS
VREF
GND
AIN
D
D
− TLV2542: Dual Channels With
Autosweep
− TLV2545: Single Channel With
Pseudo-Differential Input
Low Power With Autopower Down
− Operating Current: 1 mA at 2.7 V, 1.5 mA
at 5 V
Autopower Down: 2 μA at 2.7 V, 5 μA
at 5 V
Small 8-Pin MSOP and SOIC Packages
TOP VIEW
TLV2542
1
8
2
7
3
6
4
5
SDO
FS
VDD
SCLK
CS
VREF
GND
AIN0
TOP VIEW
TLV2545
1
8
2
7
3
6
4
5
SDO
SCLK
VDD
AIN1
CS
VREF
GND
AIN(+)
1
8
2
7
3
6
4
5
SDO
SCLK
VDD
AIN(−)
description
The TLV2541, TLV2542, and TLV2545 are a family of high performance, 12-bit, low power, miniature, CMOS
analog-to-digital converters (ADC). The TLV254x family operates from a single 2.7-V to 5.5-V supply. Devices
are available with single, dual, or single pseudo-differential inputs. Each device has a chip select (CS), serial
clock (SCLK), and serial data output (SDO) that provides a direct 3-wire interface to the serial port of most
popular host microprocessors (SPI interface). When interfaced with a TMS320t DSP, a frame sync signal (FS)
can be used to indicate the start of a serial data frame on CS for all devices or FS for the TLV2541.
TLV2541, TLV2542, and TLV2545 are designed to operate with very low power consumption. The power saving
feature is further enhanced with an autopower-down mode. This product family features a high-speed serial link
to modern host processors with SCLK up to 20 MHz. The maximum SCLK frequency is dependent upon the
mode of operation (see Table 1). The TLV254x family uses the built-in oscillator as the conversion clock,
providing a 3.5-μs conversion time.
AVAILABLE OPTIONS
PACKAGED DEVICES
TA
8-MSOP
(DGK)
8-SOIC
(D)
TLV2541CDGK (AGZ)
0°C
70°C
0
C to 70
C
TLV2542CDGK (AHB)
TLV2545CDGK (AHD)
−40°C
40 C to 85°C
85 C
TLV2541IDGK (AHA)
TLV2541ID
TLV2542IDGK (AHC)
TLV2542ID
TLV2545IDGK (AHE)
TLV2545ID
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
TMS320 is a trademark of Texas Instruments.
Copyright © 2000 − 2003, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
1
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
functional block diagram
TLV2541
TLV2542
VDD
VDD
VREF
VREF
AIN0
S/H
AIN
OSC
SCLK
CS
FS
LOW POWER
12-BIT
SAR ADC
Mux
AIN1
SDO
Conversion
Clock
OSC
CONTROL
LOGIC
SCLK
CS
GND
Conversion
Clock
CONTROL
LOGIC
GND
TLV2545
VDD
VREF
AIN (+)
OSC
SCLK
CS
LOW POWER
12-BIT
SAR ADC
S/H
AIN (−)
Conversion
Clock
CONTROL
LOGIC
GND
2
LOW POWER
SAR ADC
S/H
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SDO
SDO
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
Terminal Functions
TLV2541
TERMINAL
NAME
NO.
I/O
DESCRIPTION
AIN
4
I
Analog input channel
CS
1
I
Chip select. A high-to-low transition on the CS input removes SDO from 3-state within a maximum setup time.
CS can be used as the FS pin when a dedicated DSP serial port is used.
FS
7
I
DSP frame sync input. Indication of the start of a serial data frame. Tie this terminal to VDD if not used.
GND
3
I
Ground return for the internal circuitry. Unless otherwise noted, all voltage measurements are with respect to GND.
SCLK
5
I
Output serial clock. This terminal receives the serial SCLK from the host processor.
SDO
8
O
The 3-state serial output for the A/D conversion result. SDO is kept in the high-impedance state until CS falling edge
or FS rising edge, whichever occurs first. The output format is MSB first.
When FS is not used (FS = 1 at the falling edge of CS): The MSB is presented to the SDO pin after CS falling edge
and output data is valid on the first falling edge of SCLK.
When CS and FS are both used (FS = 0 at the falling edge of CS): The MSB is presented to the SDO pin after the
falling edge of CS. When CS is tied/held low, the MSB is presented on SDO after the rising FS. Output data is valid
on the first falling edge of SCLK. (This is typically used with an active FS from a DSP using a dedicated serial port.)
VDD
6
I
Positive supply voltage
VREF
2
I
External reference input
TLV2542/45
TERMINAL
I/O
DESCRIPTION
NAME
NO.
AIN0 /AIN(+)
4
I
Analog input channel 0 for TLV2542—Positive input for TLV2545.
AIN1/AIN (−)
5
I
Analog input channel 1 for TLV2542—Inverted input for TLV2545.
CS
1
I
Chip select. A high-to-low transition on CS removes SDO from 3-state within a maximum delay time. This pin can
be connected to the frame sync of a DSP using a dedicated serial port.
GND
3
I
Ground return for the internal circuitry. Unless otherwise noted, all voltage measurements are with respect to GND.
SCLK
7
I
Output serial clock. This terminal receives the serial SCLK from the host processor.
SDO
8
O
The 3-state serial output for the A/D conversion result. SDO is kept in the high-impedance state when CS is high
and presents output data after the CS falling edge until the LSB is presented. The output format is MSB first. SDO
returns to the Hi-Z state after the 16th SCLK. Output data is valid on the falling SCLK edge.
VDD
6
I
Positive supply voltage
VREF
2
I
External reference input
detailed description
The TLV2541, TLV2542, and TLV2545 are successive approximation (SAR) ADCs utilizing a charge
redistribution DAC. Figure 1 shows a simplified version of the ADC.
The sampling capacitor acquires the signal on AIN during the sampling period. When the conversion process
starts, the SAR control logic and charge redistribution DAC are used to add and subtract fixed amounts of charge
from the sampling capacitor to bring the comparator into a balanced condition. When the comparator is
balanced, the conversion is complete and the ADC output code is generated.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
3
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
detailed description (continued)
Charge
Redistribution
DAC
_
AIN
Control
Logic
+
ADC Code
GND/AIN(−)
Figure 1. Simplified SAR Circuit
serial interface
OUTPUT DATA FORMAT
MSB
LSB
D15−D4
D3−D0
Conversion result (OD11−OD0)
Don’t care
The output data format is binary (unipolar straight binary).
binary
Zero-scale code = 000h, Vcode = GND
Full-scale code = FFFh, Vcode = VREF − 1 LSB
pseudo-differential inputs
The TLV2545 operates in pseudo-differential mode. The inverted input is available on pin 5. It can have a
maximum input ripple of ±0.2 V. This is normally used for ground noise rejection.
control and timing
start of the cycle
Each cycle may be started by either CS, FS, or a combination of both. The internal state machine requires one
SCLK high-to-low transition to determine the state of these control signals so internal blocks can be powered
up in an active cycle. Special care to SPI mode is necessary. Make sure there is at least one SCLK whenever
CS (pin 1) is high to ensure proper operation.
TLV2541
D Control via CS ( FS = 1 at the falling edge of CS)—The falling edge of CS is the start of the cycle. The MSB
should be read on the first falling SCLK edge after CS is low. Output data changes on the rising edge of
SCLK. This is typically used for a microcontroller with an SPI interface, although it can also be used for a
DSP. The microcontroller SPI interface should be programmed for CPOL = 0 (serial clock referenced to
ground) and CPHA = 1 (data is valid on the falling edge of the serial clock). At least one falling edge transition
on SCLK is needed whenever CS is brought high.
D Control via FS (CS is tied/held low)—The MSB is presented after the rising edge of FS. The falling edge
of FS is the start of the cycle. The MSB should be read on the first falling edge of SCLK after FS is low. This
is the typical configuration when the ADC is the only device on the DSP serial port.
4
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
control and timing (continued)
D Control via both CS and FS—The MSB is presented after the falling edge of CS. The falling edge of FS is
the start of the sampling cycle. The MSB should be read on the first falling SCLK edge after FS is low. Output
data changes on the rising edge of SCLK. This configuration is typically used for multiple devices connected
to a TMS320 DSP.
TLV2542/5
All control is provided using CS (pin 1) on the TLV2542 and TLV2545. The cycle is started on the falling edge
transition provided by either a CS signal from an SPI microcontroller or FS signal from a TMS320 DSP. Timing
is similar to the TLV2541, with control via CS only.
TLV2542 channel MUX reset cycle
The TLV2542 uses CS to reset the analog input multiplexer. A short active CS cycle (4 to 7 SCLKs) resets the
MUX to AIN0. When the CS cycle time is greater than 7 SCLKs in duration, as in the case for a complete
conversion cycle (CS is low for 16 SCLKs plus maximum conversion time), the MUX toggles to the next channel
(see Figure 4 for timing). One dummy conversion cycle is recommended after power up before attempting to
reset the MUX.
sampling
The converter sample time is 12 SCLKs in duration, beginning on the fifth SCLK received after the converter
has received a high-to-low CS transition (or a high-to-low FS transition for the TLV2541).
conversion
The TLV2541, TLV2542, and TLV2545 complete conversions in the following manner. The conversion is started
after the 16th SCLK falling edge and takes 3.5 μs to complete. Enough time (for conversion) should be allowed
before a rising CS or FS edge so that no conversion is terminated prematurely.
TLV2542 input channel selection is toggled on each rising CS edge. The MUX channel can be reset to AIN0
via CS as described in the earlier section and in Figure 4. The input is sampled for 12 SCLKs, converted, and
the result is presented on SDO during the next cycle. Care should also be taken to allow enough time between
samples to avoid prematurely terminating the cycle, which occurs on a rising CS transition if the conversion is
not complete.
The SDO data presented during a cycle is the result of the conversion of the sample taken during the previous
cycle.
timing diagrams/conversion cycles
1
2
3
4
5
6
7
12
13
14
15
16
1
SCLK
CS
FS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
t(sample)
SDO
OD11
OD10
OD9
OD8
OD7
OD6
OD5
tc
t(powerdown)
OD0
Figure 2. TLV2541 Timing: Control via CS (FS = 1)
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
5
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
timing diagrams/conversion cycles (continued)
1
2
3
4
5
6
12
13
14
15
16
1
SCLK
CS
FS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
t(sample)
SDO
OD11
OD10
OD9
OD8
OD7
OD6
t(powerdown)
tc
OD0
Figure 3. TLV2541 Timing: Control via CS and FS or FS Only
1
2
3
4
5
1
4
12
16
1
4
12
16
SCLK
>8 SCLKs, MUX Toggles to AIN1
<8 SCLKs, MUX
Resets to AIN0
CS
t(powerdown)
t(sample)
ÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎ ÎÎÎÎÎÎÎ
SDO
t(sample)
tc
AIN0 Result
OD11
ÎÎÎ
ÎÎÎ
tc
OD0
Figure 4. TLV2542 Reset Timing
1
2
3
4
5
6
7
12
13
14
15
16
1
SCLK
CS
ÎÎÎÎÎÎ
ÎÎÎÎÎÎ
t(sample)
SDO
OD11
OD10
OD9
OD8
OD7
OD6
OD5
OD0
tc
t(powerdown)
OD11
OD10
OD9
Figure 5. TLV2542 and TLV2545 Timing
using CS as the FS input
When interfacing the TLV2541 with the TMS320 DSP, the FSR signal from the DSP may be connected to the
CS input if this is the only device on the serial port. This saves one output terminal from the DSP. (Output data
changes on the falling edge of SCLK. This is the default configuration for the TLV2542 and TLV2545.)
6
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
using CS as the FS input (continued)
SCLK and conversion speed
The input frequency of SCLK can range from 100 kHz to 20 MHz maximum. The ADC conversion uses a
separate internal oscillator with a minimum frequency of 4 MHz. The conversion cycle takes 14 internal oscillator
clocks to complete. This leads to a 3.5-μs conversion time. For a 20-MHz SCLK, the minimum total cycle time
is given by: 16x(1/20M)+14x(1/4M)+one SCLK = 4.35 μs. An additional SCLK is added to account for the
required CS and/or FS high time. These times specify the minimum cycle time for an active CS or FS signal.
If violated, the conversion terminates, invalidating the next data output cycle. Table 1 gives the maximum SCLK
frequency for a given supply voltage and operational mode.
control via pin 1 (CS, SPI interface)
All devices are compatible with this mode operation. A falling CS initiates the cycle (for TLV2541, the FS input
is tied to VDD). CS remains low for the entire cycle time (sample+convert+one SCLK) and can then be released.
NOTE:
IMPORTANT: A single SCLK is required whenever CS is high.
control via pin 1 (CS, DSP interface)
All devices are compatible with this mode of operation. The FS signal from a DSP is connected directly to the
CS input of the ADC. A falling edge on the CS input initiates the cycle. (For the TLV2541, the FS input can be
tied to VDD, although better performance can be achieved when using the FS input for control. Refer to the next
section.) The CS input should remain low for the entire cycle time (sample+convert+one SCLK) and can then
be released.
NOTE:
IMPORTANT: A single SCLK is required whenever CS is high. This should be of little consequence,
since SCLK is normally always present when interfacing with a DSP.
control via pin 1 and pin 7 (CS and FS or FS only, DSP interface)
Only the TLV2541 is compatible with this mode of operation. The CS input to the ADC can be controlled via a
general-purpose I/O pin from the DSP. The FS signal from the DSP is connected directly to the FS input of the
ADC. A falling edge on CS, if used, releases the MSB on the SDO output. When CS is not used, the rising FS
edge releases the MSB. The falling edge on the FS input while SCLK is high initiates the cycle. The CS and
FS inputs should remain low for the entire cycle time (sample+convert+one SCLK) and can then be released.
reference voltage
An external reference is applied via VREF. The voltage level applied to this pin establishes the upper limit of the
analog inputs to produce a full-scale reading. The value of VREF and the analog input should not exceed the
positive supply or be less than GND, consistent with the specified absolute maximum ratings. The digital output
is at full scale when the input signal is equal to or higher than VREF and at zero when the input signal is equal
to or lower than GND.
power down and power up
Autopower down is built into these devices in order to reduce power consumption. The actual power savings
depends on the inactive time between cycles and the power supply (loading) decoupling/storage capacitors.
Power-down takes effect immediately after the conversion is complete. This is fast enough to provide some
power savings between cycles with longer than 1 SCLK inactive time. The device power goes down to 5 μA
within 0.5 μs. To achieve the lowest power-down current (deep powerdown) of 1 μA requires 2-ms inactive time
between cycles. The power-down state is initiated at the end of conversion. These devices wake up immediately
at the next falling edge of CS or the rising edge of FS.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
7
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
ICC
VDD = 5 V
With 1-μF/0.1-μF Capacitor Between Supply and Ground
VDD = 2.7 V
0.5 μS
2 mS
1.5 mA
0.95 mA
5 μA
2 μA
1 μA
1 μA
t(Powerdown) − Powerdown time − S
Table 1. Modes of Operation and Data Throughput
MAX SCLK (MHz)
(50/50 duty cycle)
CONTROL PIN(s)/DEVICE
APPROXIMATE
CONVERSION
THROUGHPUT
(ksps)
VDD = 2.7 V
VDD = 4.5 V
VDD = 2.7 V
VDD = 4.5 V
For SPI interface†
10
15
175
200
For DSP interface (Use CS as FS)‡
5
8
140
175
15
20
200
200
CS control only (TLV2541 only)
CS and FS control (TLV2541
only)§
DSP interface
†
See Figure 29(a).
‡ See Figure 29(b).
§ See Figure 29(c).
absolute maximum ratings over operating free-air temperature (unless otherwise noted)¶
¶
8
Supply voltage range, GND to VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 6.5 V
Analog input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VDD + 0.3 V
Reference input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDD + 0.3 V
Digital input voltage range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VDD+ 0.3 V
Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 150°C
Operating free-air temperature range, TA: C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
recommended operating conditions
Supply voltage, VDD
MIN
NOM
MAX
2.7
3.3
5.5
UNIT
V
Positive external reference voltage input, VREFP (see Note 1)
2
VDD
V
Analog input voltage (see Note 1)
0
VDD
V
High level control input voltage, VIH
2.1
V
Low-level control input voltage, VIL
0.6
Setup time, CS falling edge before first SCLK falling edge, VDD = REF = 4.5 V
tsu(CSL-SCLKL)
VDD = REF = 2.7 V
Hold time, CS falling edge after SCLK falling edge, th(SCLKL-CSL)
40
ns
70
5
Delay time, delay from CS falling edge to FS rising edge, td(CSL-FSH) (TLV2541 only)
0.5
Setup time, FS rising edge before SCLK falling edge, tsu(FSH-SCLKL) (TLV2541 only)
0.35
V
ns
7
SCLKs
SCLKs
Hold time, FS high after SCLK falling edge, th(SCLKL-FSL) (TLV2541 only)
0.65
SCLKs
Pulse width CS high time, tw(H_CS)
100
ns
Pulse width FS high time, tw(H_FS) (TLV2541 only)
0.75
SCLKs
SCLK cycle time, VDD = 3.6 V to 2.7 V, tc(SCLK) (maximum tolerance of 40/60 duty cycle)
90
10000
SCLK cycle time, VDD = 5.5 V to 4.5 V, tc(SCLK) (maximum tolerance of 40/60 duty cycle)
50
10000
Pulse width low time, tw(L_SCLK)
0.4
0.6
SCLK
Pulse width high time, tw(H_SCLK)
0.4
0.6
SCLK
Hold time, hold from end of conversion to CS high, th(EOC-CSH) (EOC is internal, indicates end of conversion
time, tc)
Active CS cycle time to reset internal MUX to AIN0, t(reset cycle) (TLV2542 only)
0.05
4
7
40
VDD = REF = 2.7 V, 25-pF load
70
Delay time, delay from FS falling edge to SDO valid, td(FSL-SDOV) VDD = REF = 4.5 V, 25-pF load
(TLV2541 only)
VDD = REF = 2.7 V, 25-pF load
1
1
Delay time, delay from SCLK rising edge to SDO valid,
td(SCLKH-SDOV)
VDD = REF = 4.5 V, 25-pF load
11
VDD = REF = 2.7 V, 25-pF load
21
Delay time, delay from 17th SCLK rising edge to SDO 3-state,
3 state,
td(SCLK17H-SDOZ)
VDD = REF = 4.5 V, 25-pF load
30
VDD = REF = 2.7 V, 25-pF load
60
Conversion time, tc
Conversion clock = internal
oscillator
2.1
Sampling time, t(sample)
See Note 2
300
TLV2541/2/5C
Operating free-air
free air temperature
temperature, TA
TLV2541/2/5I
2.6
ns
μs
VDD = REF = 4.5 V, 25-pF load
Delay time,
time delay from CS falling edge to SDO valid,
valid td(CSL-SDOV)
ns
3.5
SCLKs
ns
ns
ns
ns
μs
ns
0
70
−40
85
°C
NOTES: 1. Analog input voltages greater than that applied to VREF convert as all ones (111111111111), while input voltages less than that applied
to GND convert as all zeros(000000000000).
2. Minimal t(sample) is given by 0.9 × 50 pF × (RS + 0.5 kΩ), where RS is the source output impedance.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
9
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
electrical characteristics over recommended operating free-air temperature range,
VDD = VREF = 2.7 V to 5.5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VDD = 5.5 V, IOH = −0.2 mA at 30-pF load
VOH
High level output voltage
High-level
VOL
Low level output voltage
Low-level
IOZ
Off-state output current
(high-impedance-state)
VO = 0
IIH
High-level input current
IIL
ICC
UNIT
V
VDD−0.2
VDD = 5.5 V, IOL = 0.8 mA at 30-pF load
0.4
0.1
V
1
2.5
−2.5
VI = VDD
0.005
2.5
μA
Low-level input current
VI = 0 V
−0.00
5
2.5
μA
Operating supply current
CS at 0 V
Autopower-down current
t(powerdown) ≥ 0.5 μs
For all digital inputs,
0≤ VI ≤ 0.3 V or VI ≥ VDD− 0.3 V,
SCLK = 0, VDD = 4.5 V to 5.5 V, Ext ref
5
VDD = 2.7 V to 3.3 V,
2
Deep autopower-down current
t(powerdown) ≥ 2 ms
For all digital inputs,
0≤ VI ≤ 0.3 V or VI ≥ VDD− 0.3 V,
SCLK = 0, VDD = 4.5 V to 5.5 V, Ext ref
1
VDD = 2.7 V to 3.3 V
1
Selected channel at VDD
1
Selected channel at 0 V
−1
CS = VDD
VDD = 4.5 V to 5.5 V
1.3
1.5
VDD = 2.7 V to 3.3 V
0.85
0.95
Ext ref
Analog inputs
Input capacitance
20
Control Inputs
Input on resistance
45
50
5
25
VDD = 5.5 V
500
VDD = 2.7 V
600
Autopower down
0.5
All typical values are at VDD = 5 V, TA = 25°C.
10
MAX
2.4
−1
Selected analog input channel
leakage current
†
TYP†
VDD = 2.7 V, IOL = 20 μA at 30-pF load
VO = VDD
ICC(AUTOPWDN)
Ci
VDD = 2.7 V, IOH = -20 μA at 30-pF load
MIN
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
μA
A
mA
μA
μA
μA
A
pF
Ω
SCLK
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
ac specifications (fi = 20 kHz)
PARAMETER
SINAD
Signal to noise ratio +distortion
Signal-to-noise
THD
Total harmonic distortion
ENOB
Effective number of bits
SFDR
Spurious free dynamic range
TEST CONDITIONS
MIN
TYP
200 KSPS, VDD = VREF = 5.5 V
70
72
150 KSPS, VDD = VREF = 2.7 V
68
71
MAX
UNIT
dB
200 KSPS, VDD = VREF = 5.5 V
−84
−80
150 KSPS, VDD = VREF = 2.7 V
−84
−80
200 KSPS, VDD = VREF = 5.5 V
11.8
150 KSPS, VDD = VREF = 2.7 V
11.6
200 KSPS, VDD = VREF = 5.5 V
−84
−80
150 KSPS, VDD = VREF = 2.7 V
−84
−80
dB
Bits
dB
Analog Input
Full-power bandwidth, −3 dB
1
MHz
Full-power bandwidth, −1 dB
500
kHz
external reference specifications
PARAMETER
TEST CONDITIONS
Reference input voltage
VDD = 2.7 V to 5.5 V
UNIT
VDD
V
SCLK = 0
CS = 0,
SCLK = 20 MHz
CS = 1,
SCLK = 0
CS = 0,
SCLK = 20 MHz
VDD = VREF = 5.5 V,
CS = 0,
SCLK = 20 MHz
100
400
VDD = VREF = 2.7 V,
CS = 0,
SCLK = 20 MHz
50
200
CS = 1,
SCLK = 0
CS = 0,
SCLK = 20 MHz
CS = 1,
SCLK = 0
CS = 0,
SCLK = 20 MHz
VDD = 2
2.7
7V
VDD = VREF = 5
5.5
5V
Reference input capacitance
VDD = VREF = 2
2.7
7V
Reference voltage
MAX
CS = 1,
Reference input impedance
VREF
TYP
2
5V
VDD = 5
5.5
Reference current
MIN
100
20
MΩ
25
kΩ
100
20
MΩ
25
5
20
μA
15
45
5
20
kΩ
50
15
45
VDD = 2.7 V to 5.5 V
pF
50
VDD
V
dc specification, VDD = VREF = 2.7 V to 5.5 V, SCLK frequency = 20 MHz at 5 V, 15 MHz at 3 V (unless otherwise
noted)
PARAMETER
INL
Integral linearity error (see Note 4)
DNL
Differential linearity error
TEST CONDITIONS
See Note 3
EO
Offset error (see Note 5)
See Note 3
EG
Gain error (see Note 5)
See Note 3
Et
Total unadjusted error (see Note 6)
See Note 3
MIN
TYP
MAX
UNIT
±0.6
±1
LSB
±1
LSB
±0.5
TLV2541/42
±1.5
TLV2545
±2.5
TLV2541/42
±2
TLV2545
±5
TLV2541/42
±2
TLV2545
±5
LSB
LSB
LSB
NOTES: 3. Analog input voltages greater than that applied to VREF convert as all ones (111111111111).
4. Linear error is the maximum deviation from the best straight line through the A/D transfer characteristics.
5. Zero error is the difference between 000000000000 and the converted output for zero input voltage: full-scale error is the difference
between 111111111111 and the converted output for full-scale input voltage.
6. Total unadjusted error comprises linearity, zero, and full-scale errors.
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
11
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
PARAMETER MEASUREMENT INFORMATION
t(sample)
tc
tw(H_SCLK)
VIH
1
2
4
12
16
SCLK
VIL
tw(L_SCLK)
tsu(CSL-SCLKL)
t(powerdown)
CS
th(SCLKL-FSL)
tw(H_CS)
tsu(FSH-SCLKL)
th(EOC-CSH)
td(CSL-FSH)
td(SCLKH-SDOV)
FS
SDO
ÎÎÎÎÎ
ÎÎÎÎÎ
tw(H_FS)
OD11
OD8
OD0
td(CSL-SDOV)
ÎÎÎÎÎ
ÎÎÎÎÎ
td(SCLK17H-SDOZ)
Figure 6. TLV2541 Critical Timing (Control via CS and FS or FS only)
t(sample)
tsu(CSL−SCLKL)
1
2
tc
4
12
16
SCLK
t(powerdown)
CS
td(SCLKH-SDOV)
SDO
OD11
OD10
OD9
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
td(SCLK17H-SDOZ)
OD0
td(CSL-SDOV)
Figure 7. TLV2541 Critical Timing (Control via CS only, FS = 1)
12
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
th(EOC−CSH)
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
PARAMETER MEASUREMENT INFORMATION
t(sample)
tc
1
1
4
12
16
SCLK
t(reset cycle)
MUX = AIN0
CS
tw(H_CS)
ÎÎÎÎ
ÎÎÎÎ
SDO
th(EOC-CSH)
td(SCLKH-SDOV)
td(CSL-SDOV)
OD11
OD0
td(CSL-SDOV)
ÎÎÎÎÎ
ÎÎÎÎÎ
OD11
td(SCLK17H-SDOZ)
Figure 8. TLV2542 Reset Cycle Critical Timing
t(sample)
tw(H_SCLK)
VIH
1
2
4
12
tc
16
SCLK
VIL
th(SCLKL-CSL)
tw(L_SCLK)
t(powerdown)
tsu(CSL-SCLKL)
CS
tw(H_CS)
SDO
th(EOC-CSH)
td(SCLKH-SDOV)
OD11
OD8
td(CSL-SDOV)
OD0
ÎÎÎÎÎ
ÎÎÎÎÎ
td(SCLK17H-SDOZ)
Figure 9. TLV2542 and TLV2545 Conversion Cycle Critical Timing
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
13
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
TYPICAL CHARACTERISTICS
INTEGRAL NONLINEARITY
vs
FREE-AIR TEMPERATURE
INTEGRAL NONLINEARITY
vs
FREE-AIR TEMPERATURE
0.7
0.6
VDD = REF = 5.5 V
200 KSPS
INL − Integral Nonlinearity − LSB
INL − Integral Nonlinearity − LSB
VDD = REF = 2.7 V
150 KSPS
0.65
0.6
−40
0.5
−40
90
25
0.55
25
TA − Free-Air Temperature − °C
Figure 10
Figure 11
DIFFERENTIAL NONLINEARITY
vs
FREE-AIR TEMPERATURE
DIFFERENTIAL NONLINEARITY
vs
FREE-AIR TEMPERATURE
0.35
VDD = REF = 2.7 V
150 KSPS
DNL − Differential Nonlinearity − LSB
DNL − Differential Nonlinearity − LSB
0.6
0.5
0.4
0.3
0.2
0.1
0
−40
25
TA − Free-Air Temperature − °C
VDD = REF = 5.5 V
200 KSPS
0.3
0.25
−40
90
Figure 12
14
90
TA − Free-Air Temperature − °C
25
TA − Free-air Temperature − °C
Figure 13
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
90
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
TYPICAL CHARACTERISTICS
OFFSET ERROR
vs
FREE-AIR TEMPERATURE
GAIN ERROR
vs
FREE-AIR TEMPERATURE
0.5
0.9
VDD = REF = 2.7 V
150 KSPS
VDD = REF = 5.5 V
200 KSPS
Gain Error − LSB
0.3
0.2
0.85
0.1
0
−40
0.8
−40
90
25
TA − Free-Air Temperature − °C
25
TA − Free-Air Temperature − °C
Figure 14
90
Figure 15
SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
1.5
VDD = REF = 5.5 V
200 KSPS
Supply Current − mA
Offset Error − LSB
0.4
1.4
1.3
1.2
−40
25
TA − Free-Air Temperature − °C
90
Figure 16
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
15
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
TYPICAL CHARACTERISTICS
INL − Integral Nonlinearity − LSB
INTEGRAL NONLINEARITY ERROR
vs
DIGITAL OUTPUT CODES
1
VDD = REF = 2.7 V
150 KSPS
0.5
0
−0.5
−1
4095
1
Digital Output Codes
Figure 17
DNL − Differential Nonlinearity − LSB
DIFFERENTIAL NONLINEARITY ERROR
vs
DIGITAL OUTPUT CODES
1
VDD = REF = 2.7 V
150 KSPS
0.5
0
−0.5
−1
4095
1
Digital Output Codes
Figure 18
16
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
TYPICAL CHARACTERISTICS
INL − Integral Nonlinearity − LSB
INTEGRAL NONLINEARITY ERROR
vs
DIGITAL OUTPUT CODES
1
VDD = REF = 5.5 V
200 KSPS
0.5
0
−0.5
−1
4095
1
Digital Output Codes
Figure 19
DNL − Differential Nonlinearity − LSB
DIFFERENTIAL NONLINEARITY ERROR
vs
DIGITAL OUTPUT CODES
1
VDD = REF = 5.5 V
200 KSPS
0.5
0
−0.5
−1
1
4095
Digital Output Codes
Figure 20
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
17
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
TYPICAL CHARACTERISTICS
2048 POINTS FAST FOURIER TRANSFORM (FFT)
0
VDD = REF = 2.7 V
150 KSPS
fi = 20 kHz
Magnitude − dB
−20
−40
−60
−80
−100
−120
−140
0
20
40
60
80
100
f − Input Frequency − KHz
Figure 21
2048 POINTS FAST FOURIER TRANSFORM (FFT)
0
VDD = REF = 5.5 V
200 KSPS
fi = 20 kHz
Magnitude − dB
−20
−40
−60
−80
−100
−120
−140
0
20
40
60
f − Input Frequency − KHz
Figure 22
18
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
80
100
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
TYPICAL CHARACTERISTICS
SIGNAL-TO-NOISE + DISTORTION
vs
INPUT FREQUENCY
SIGNAL-TO-NOISE + DISTORTION
vs
INPUT FREQUENCY
75
VDD = REF = 2.7 V
150 KSPS
SINAD − Signal-To-Noise + Distortion − dB
SINAD − Signal-To-Noise + Distortion − dB
75
73
71
69
67
65
0
10
20
30
40
50
60
70
VDD = REF = 5.5 V
200 KSPS
73
71
69
67
65
80
0
20
Figure 23
ENOB − Effective Number Of Bits − Bits
ENOB − Effective Number Of Bits − Bits
11.8
11.6
11.4
11.2
20
30
100
12
VDD = REF = 2.7 V
150 KSPS
10
80
EFFECTIVE NUMBER OF BITS
vs
INPUT FREQUENCY
12
0
60
Figure 24
EFFECTIVE NUMBER OF BITS
vs
INPUT FREQUENCY
11
40
f − Input Frequency − KHz
f − Input Frequency − KHz
40
50
60
70
11.8
11.7
11.6
11.5
11.4
11.3
11.2
11.1
11
80
f − Input Frequency − KHz
VDD = REF = 5.5 V
200 KSPS
11.9
0
20
40
60
80
100
f − Input Frequency − KHz
Figure 25
Figure 26
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
19
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION
vs
INPUT FREQUENCY
THD − Total Harmonic Distortion − dB
−75
VDD = REF = 2.7 V
150 KSPS
−76
−77
−78
−79
−80
−81
−82
−83
−84
−85
0
10
30
20
40
50
70
60
80
f − Input Frequency − KHz
Figure 27
TOTAL HARMONIC DISTORTION
vs
INPUT FREQUENCY
THD − Total Harmonic Distortion − dB
−70
VDD = REF = 5.5 V
200 KSPS
−72
−74
−76
−78
−80
−82
−84
−86
−88
−90
0
20
40
60
80
f − Input Frequency − KHz
Figure 28
20
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
100
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
APPLICATION INFORMATION
VDD
VDD
10 kΩ
TLV2541
MISO
FS
SDO
VDD
SS
CS
AIN
SCLK
GND
SCLK
SPI PORT
VREF
EXT
Reference
(a)
VDD
VDD
10 kΩ
DR
CLKX
CLKR
TLV2541
FS
SDO
VDD
SCLK
AIN
FSX
CS
FSR
GND
DSP
VREF
EXT
Reference
(b)
VDD
TLV2541
FS
FSX
FSR
DR
SDO
CLKX
SCLK
VDD
AIN
CLKR
GPIO
CS
GND
DSP
VREF
EXT
Reference
(c)
Figure 29. Typical TLV2541 Interface to a TMS320 DSP
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
21
TLV2541, TLV2542, TLV2545
2.7-V TO 5.5-V, LOW-POWER, 12-BIT, 140/200 KSPS,
SERIAL ANALOG-TO-DIGITAL CONVERTERS WITH AUTOPOWER DOWN
SLAS245E −MARCH 2000 − REVISED APRIL 2010
APPLICATION INFORMATION
VDD
TMS320
EXT
Reference
10 kΩ
10 kΩ
FSX
CS
SDO
SCLK
FSR
DR
CLKR
DSP
CLKX
VDD
VREF
TLV2542/45
AIN 0/AIN (+)†
†
GND
For TLV2545 only
Figure 30. Typical TLV2542/45 Interface to a TMS320 DSP
22
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
AIN 1/AIN (−)†
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
TLV2541CDGK
ACTIVE
VSSOP
DGK
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
0 to 70
AGZ
TLV2541CDGKG4
ACTIVE
VSSOP
DGK
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
0 to 70
AGZ
TLV2541CDGKR
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
0 to 70
AGZ
TLV2541CDGKRG4
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
0 to 70
AGZ
TLV2541ID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2541I
TLV2541IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2541I
TLV2541IDGK
ACTIVE
VSSOP
DGK
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHA
TLV2541IDGKG4
ACTIVE
VSSOP
DGK
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHA
TLV2541IDGKR
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHA
TLV2541IDGKRG4
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHA
TLV2541IDR
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2541I
TLV2541IDRG4
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2541I
TLV2542CDGK
ACTIVE
VSSOP
DGK
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
0 to 70
AHB
TLV2542CDGKG4
ACTIVE
VSSOP
DGK
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
0 to 70
AHB
TLV2542CDGKR
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
0 to 70
AHB
TLV2542CDGKRG4
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
0 to 70
AHB
TLV2542ID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
2542I
CU NIPDAU
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
TLV2542IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
TLV2542IDGK
ACTIVE
VSSOP
DGK
8
80
TLV2542IDGKG4
ACTIVE
VSSOP
DGK
8
TLV2542IDGKR
ACTIVE
VSSOP
DGK
TLV2542IDGKRG4
ACTIVE
VSSOP
TLV2542IDR
ACTIVE
TLV2542IDRG4
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
CU NIPDAU
(4)
Level-1-260C-UNLIM
-40 to 85
2542I
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHC
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHC
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHC
DGK
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHC
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2542I
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2542I
TLV2545CDGK
ACTIVE
VSSOP
DGK
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
0 to 70
AHD
TLV2545CDGKG4
ACTIVE
VSSOP
DGK
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
0 to 70
AHD
TLV2545ID
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2545I
TLV2545IDG4
ACTIVE
SOIC
D
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
-40 to 85
2545I
TLV2545IDGK
ACTIVE
VSSOP
DGK
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHE
TLV2545IDGKG4
ACTIVE
VSSOP
DGK
8
80
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHE
TLV2545IDGKR
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHE
TLV2545IDGKRG4
ACTIVE
VSSOP
DGK
8
2500
Green (RoHS CU NIPDAUAG
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 85
AHE
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TLV2541CDGKR
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
TLV2541IDGKR
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
TLV2541IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLV2542CDGKR
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
TLV2542IDGKR
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
TLV2542IDR
SOIC
D
8
2500
330.0
12.4
6.4
5.2
2.1
8.0
12.0
Q1
TLV2545IDGKR
VSSOP
DGK
8
2500
330.0
12.4
5.3
3.4
1.4
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Jan-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLV2541CDGKR
VSSOP
DGK
8
2500
367.0
367.0
35.0
TLV2541IDGKR
VSSOP
DGK
8
2500
367.0
367.0
35.0
TLV2541IDR
SOIC
D
8
2500
367.0
367.0
35.0
TLV2542CDGKR
VSSOP
DGK
8
2500
367.0
367.0
35.0
TLV2542IDGKR
VSSOP
DGK
8
2500
367.0
367.0
35.0
TLV2542IDR
SOIC
D
8
2500
367.0
367.0
35.0
TLV2545IDGKR
VSSOP
DGK
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated