TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER r r TAOS099A − AUGUST 2011 D High-Resolution Conversion of Light D D D D D D D PACKAGE D 8-LEAD SOIC (TOP VIEW) Intensity to Frequency Programmable Color and Full-Scale Output Frequency Communicates Directly With a Microcontroller Single-Supply Operation (2.7 V to 5.5 V) Power Down Feature Nonlinearity Error Typically 0.2% at 50 kHz Stable 200 ppm/°C Temperature Coefficient Low-Profile Lead (Pb) Free and RoHS Compliant Surface-Mount Package S0 1 8 S3 S1 2 7 S2 OE 3 6 OUT GND 4 5 VDD TCS3200 Description The TCS3200 and TCS3210 programmable color light-to-frequency converters that combine configurable silicon photodiodes and a current-to-frequency converter on a single monolithic CMOS integrated circuit. The output is a square wave (50% duty cycle) with frequency directly proportional to light intensity (irradiance). S0 1 8 S3 S1 2 7 S2 OE 3 6 OUT GND 4 5 VDD TCS3210 The full-scale output frequency can be scaled by one of three preset values via two control input pins. Digital inputs and digital output allow direct interface to a microcontroller or other logic circuitry. Output enable (OE) places the output in the high-impedance state for multiple-unit sharing of a microcontroller input line. In the TCS3200, the light-to-frequency converter reads an 8 × 8 array of photodiodes. Sixteen photodiodes have blue filters, 16 photodiodes have green filters, 16 photodiodes have red filters, and 16 photodiodes are clear with no filters. In the TCS3210, the light-to-frequency converter reads a 4 × 6 array of photodiodes. Six photodiodes have blue filters, 6 photodiodes have green filters, 6 photodiodes have red filters, and 6 photodiodes are clear with no filters. The four types (colors) of photodiodes are interdigitated to minimize the effect of non-uniformity of incident irradiance. All photodiodes of the same color are connected in parallel. Pins S2 and S3 are used to select which group of photodiodes (red, green, blue, clear) are active. Photodiodes are 110 μm × 110 μm in size and are on 134-μm centers. Functional Block Diagram Output Photodiode Array Light S2 The LUMENOLOGY r Company Current-to-Frequency Converter S3 S0 S1 OE Copyright E 2011, TAOS Inc. r Texas Advanced Optoelectronic Solutions Inc. 1001 Klein Road S Suite 300 S Plano, TX 75074 S (972) r 673-0759 www.taosinc.com 1 TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 Terminal Functions TERMINAL NAME I/O NO. DESCRIPTION GND 4 OE 3 I OUT 6 O S0, S1 1, 2 I Output frequency (fo). Output frequency scaling selection inputs. S2, S3 7, 8 I Photodiode type selection inputs. VDD Power supply ground. All voltages are referenced to GND. 5 Enable for fo (active low). Supply voltage Table 1. Selectable Options S0 S1 OUTPUT FREQUENCY SCALING (fo) S2 S3 PHOTODIODE TYPE L L Power down L L Red L H 2% L H Blue H L 20% H L Clear (no filter) H H 100% H H Green Available Options DEVICE TA PACKAGE − LEADS PACKAGE DESIGNATOR TCS3200 −40°C to 85°C SOIC−8 D TCS3200D TCS3210 −40°C to 85°C SOIC−8 D TCS3210D Copyright E 2011, TAOS Inc. The LUMENOLOGY r Company r r 2 ORDERING NUMBER www.taosinc.com TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Input voltage range, all inputs, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to VDD + 0.3 V Operating free-air temperature range, TA (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C Storage temperature range (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C Solder conditions in accordance with JEDEC J−STD−020A, maximum temperature (see Note 3) . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values are with respect to GND. 2. Long-term storage or operation above 70°C could cause package yellowing that will lower the sensitivity to wavelengths < 500nm. 3. The device may be hand soldered provided that heat is applied only to the solder pad and no contact is made between the tip of the solder iron and the device lead. The maximum time heat should be applied to the device is 5 seconds. Recommended Operating Conditions Supply voltage, VDD MIN NOM 2.7 5 MAX UNIT 5.5 V High-level input voltage, VIH VDD = 2.7 V to 5.5 V 2 VDD V Low-level input voltage, VIL Operating free-air temperature range, TA VDD = 2.7 V to 5.5 V 0 0.8 V −40 70 °C Electrical Characteristics at TA = 25°C, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP 4 4.5 MAX UNIT VOH High-level output voltage IOH = − 2 mA VOL Low-level output voltage IOL = 2 mA 0.40 V IIH High-level input current 5 μA IIL Low-level input current 5 μA 2 mA IDD Supply current 0.1 μA 0.25 Power-on mode Full-scale Full scale frequency (See Note 4) kSVS 1.4 Power-down mode V S0 = H, S1 = H 500 600 kHz S0 = H, S1 = L 100 120 kHz S0 = L, S1 = H 10 12 kHz Temperature coefficient of responsivity λ ≤ 700 nm, −25°C ≤ TA ≤ 70°C ± 200 ppm/°C Supply voltage sensitivity VDD = 5 V ±10% ±0.5 %/ V NOTE 4: Full-scale frequency is the maximum operating frequency of the device without saturation. The LUMENOLOGY r Company Copyright E 2011, TAOS Inc. r r www.taosinc.com 3 TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 Operating Characteristics at VDD = 5 V, TA = 25°C, S0 = H, S1 = H (unless otherwise noted) (See Notes 5, 6, 7, and 8). Values for TCS3200 (TCS3210) are below. PARAMETER TEST CONDITIONS Output frequency (Note 9) MIN TYP MAX Ee = 47.2 λp = 470 nm 15.6 18.7 (4.7) (5.85) (7) Ee = 40.4 μW/cm2, λp = 524 nm 12.5 15.6 18.7 (4.7) (5.85) (7) Ee = 34.6 μW/cm2, λp = 640 nm 13.1 16.4 19.7 (4.9) (6.15) (7.4) λp = 470 nm Re Irradiance responsivity λp = 524 nm (Note 10) λp = 640 nm λp = 470 nm Saturation irradiance (Note 11) λp = 524 nm λp = 640 nm fD Dark frequency BLUE PHOTODIODE S2 = L, S3 = H 12.5 μW/cm2, fO CLEAR PHOTODIODE S2 = H, S3 = L MIN TYP GREEN PHOTODIODE S2 = H, S3 = H MAX MIN 61% 84% 8% TYP RED PHOTODIODE S2 = L, S3 = L TYP UNIT MAX MIN MAX 22% 43% 0% 6% 28% 57% 80% 9% 27% 5% 21% 0% 12% 84% 105% 61% 84% 22% 43% 0% 6% 8% 28% 57% 80% 9% 27% 5% 21% 0% 12% 84% 105% kHz 331 (124) 386 (145) Hz/ (μW/ ( W/ cm2) 474 (178) 1813 (4839) −− −− −− −− −− −− −− −− −− 1554 (4138) μW/ cm2 1266 (3371) Ee = 0 2 10 2 10 2 10 2 10 Hz ± 0.1 ± 0.1 ± 0.1 ± 0.1 ± 0.2 ± 0.2 ± 0.2 ± 0.2 ± 0.5 ± 0.5 ± 0.5 ± 0.5 Recovery from power down 100 100 100 100 μs Response time to output enable (OE) 100 100 100 100 ns fO = 0 to 5 kHz Nonlinearity f = 0 to 50 kHz O (Note 12) fO = 0 to 500 kHz % F.S. NOTES: 5. Optical measurements are made using small-angle incident radiation from a light-emitting diode (LED) optical source. 6. The 470 nm input irradiance is supplied by an InGaN light-emitting diode with the following characteristics: peak wavelength λp = 470 nm, spectral halfwidth Δλ½ = 35 nm, and luminous efficacy = 75 lm/W. 7. The 524 nm input irradiance is supplied by an InGaN light-emitting diode with the following characteristics: peak wavelength λp = 524 nm, spectral halfwidth Δλ½ = 47 nm, and luminous efficacy = 520 lm/W. 8. The 640 nm input irradiance is supplied by a AlInGaP light-emitting diode with the following characteristics: peak wavelength λp = 640 nm, spectral halfwidth Δλ½ = 17 nm, and luminous efficacy = 155 lm/W. 9. Output frequency Blue, Green, Red percentage represents the ratio of the respective color to the Clear channel absolute value. 10. Irradiance responsivity Re is characterized over the range from zero to 5 kHz. 11. Saturation irradiance = (full-scale frequency)/(irradiance responsivity) for the Clear reference channel. 12. Nonlinearity is defined as the deviation of fO from a straight line between zero and full scale, expressed as a percent of full scale. Copyright E 2011, TAOS Inc. The LUMENOLOGY r Company r r 4 www.taosinc.com TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 TYPICAL CHARACTERISTICS NORMALIZED OUTPUT FREQUENCY vs. ANGULAR DISPLACEMENT PHOTODIODE SPECTRAL RESPONSIVITY 1 Clear TA = 25°C 0.7 Red 0.6 Green Blue 0.5 0.4 0.3 0.2 0.1 0 300 0.8 Optical Axis Blue 0.8 fO — Output Frequency — Normalized 0.9 Relative Responsivity 1 Normalized to Clear @ 715 nm 0.6 0.4 0.2 Angular Displacement is Equal for Both Aspects Green 500 700 900 λ − Wavelength − nm 0 −90 1100 −60 −30 0 30 60 − Angular Displacement − ° Figure 1 90 Figure 2 IDD vs. VDD vs. TEMPERATURE NORMALIZED OUTPUT vs. VDD 100.6 1.55 1.5 1.4 100.4 Saturated VDD = 5 V Normalized Output — % 1.45 IDD — mA 1.35 1.3 1.25 Saturated VDD = 3 V 1.2 1.15 Dark VDD = 3 V 1.1 1.05 1 0 100.2 100 99.8 99.6 Dark VDD = 5 V 99.4 25 50 75 TA − Free-Air Temperature − °C 100 2.5 3 3.5 Figure 3 The LUMENOLOGY r Company 4 4.5 5 5.5 VDD − V Figure 4 Copyright E 2011, TAOS Inc. r r www.taosinc.com 5 TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 TYPICAL CHARACTERISTICS PHOTODIODE RESPONSIVITY TEMPERATURE COEFFICIENT vs. WAVELENGTH OF INCIDENT LIGHT 9k Temperature Coefficient — ppm/deg C 8k 7k 6k 5k 4k 3k 2k 1k 0 600 650 700 750 800 850 900 950 1000 λ − Wavelength of Incident Light − nm Figure 5 Copyright E 2011, TAOS Inc. The LUMENOLOGY r Company r r 6 www.taosinc.com TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 APPLICATION INFORMATION Power supply considerations Power-supply lines must be decoupled by a 0.01-μF to 0.1-μF capacitor with short leads mounted close to the device package. Input interface A low-impedance electrical connection between the device OE pin and the device GND pin is required for improved noise immunity. All input pins must be either driven by a logic signal or connected to VDD or GND — they should not be left unconnected (floating). Output interface The output of the device is designed to drive a standard TTL or CMOS logic input over short distances. If lines greater than 12 inches are used on the output, a buffer or line driver is recommended. A high state on Output Enable (OE) places the output in a high-impedance state for multiple-unit sharing of a microcontroller input line. Power down Powering down the sensor using S0/S1 (L/L) will cause the output to be held in a high-impedance state. This is similar to the behavior of the output enable pin, however powering down the sensor saves significantly more power than disabling the sensor with the output enable pin. Photodiode type (color) selection The type of photodiode (blue, green, red, or clear) used by the device is controlled by two logic inputs, S2 and S3 (see Table 1). Output frequency scaling Output-frequency scaling is controlled by two logic inputs, S0 and S1. The internal light-to-frequency converter generates a fixed-pulsewidth pulse train. Scaling is accomplished by internally connecting the pulse-train output of the converter to a series of frequency dividers. Divided outputs are 50%-duty cycle square waves with relative frequency values of 100%, 20%, and 2%. Because division of the output frequency is accomplished by counting pulses of the principal internal frequency, the final-output period represents an average of the multiple periods of the principle frequency. The output-scaling counter registers are cleared upon the next pulse of the principal frequency after any transition of the S0, S1, S2, S3, and OE lines. The output goes high upon the next subsequent pulse of the principal frequency, beginning a new valid period. This minimizes the time delay between a change on the input lines and the resulting new output period. The response time to an input programming change or to an irradiance step change is one period of new frequency plus 1 μs. The scaled output changes both the full-scale frequency and the dark frequency by the selected scale factor. The frequency-scaling function allows the output range to be optimized for a variety of measurement techniques. The scaled-down outputs may be used where only a slower frequency counter is available, such as low-cost microcontroller, or where period measurement techniques are used. The LUMENOLOGY r Company Copyright E 2011, TAOS Inc. r r www.taosinc.com 7 TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 APPLICATION INFORMATION Measuring the frequency The choice of interface and measurement technique depends on the desired resolution and data acquisition rate. For maximum data-acquisition rate, period-measurement techniques are used. Output data can be collected at a rate of twice the output frequency or one data point every microsecond for full-scale output. Period measurement requires the use of a fast reference clock with available resolution directly related to reference clock rate. Output scaling can be used to increase the resolution for a given clock rate or to maximize resolution as the light input changes. Period measurement is used to measure rapidly varying light levels or to make a very fast measurement of a constant light source. Maximum resolution and accuracy may be obtained using frequency-measurement, pulse-accumulation, or integration techniques. Frequency measurements provide the added benefit of averaging out random- or high-frequency variations (jitter) resulting from noise in the light signal. Resolution is limited mainly by available counter registers and allowable measurement time. Frequency measurement is well suited for slowly varying or constant light levels and for reading average light levels over short periods of time. Integration (the accumulation of pulses over a very long period of time) can be used to measure exposure, the amount of light present in an area over a given time period. PCB Pad Layout Suggested PCB pad layout guidelines for the D package are shown in Figure 6. 4.65 6.90 1.27 2.25 0.50 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. Figure 6. Suggested D Package PCB Layout Copyright E 2011, TAOS Inc. The LUMENOLOGY r Company r r 8 www.taosinc.com TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 MECHANICAL INFORMATION This SOIC package consists of an integrated circuit mounted on a lead frame and encapsulated with an electrically nonconductive clear plastic compound. The TCS3200 has an 8 × 8 array of photodiodes with a total size of 1 mm by 1 mm. The photodiodes are 110 μm × 110 μm in size and are positioned on 134 μm centers. PACKAGE D PLASTIC SMALL-OUTLINE NOTE B TOP VIEW 2.12 0.250 BOTTOM VIEW 3.00 0.250 PIN 1 PIN 1 8 0.510 0.330 6 1.27 SIDE VIEW 2.8 TYP CLEAR WINDOW 5.00 4.80 END VIEW 0.50 0.25 5.3 MAX 45 0.88 TYP TOP OF SENSOR DIE A 1.75 1.35 DETAIL A 4.00 3.80 6.20 5.80 0.25 0.19 Pb NOTES: A. B. C. D. 1.27 0.41 0.25 0.10 All linear dimensions are in millimeters. The center of the 1-mm by 1-mm photo-active area is referenced to the upper left corner tip of the lead frame (Pin 1). Package is molded with an electrically nonconductive clear plastic compound having an index of refraction of 1.55. This drawing is subject to change without notice. Figure 7. Package D — TCS3200 Plastic Small Outline IC Packaging Configuration The LUMENOLOGY r Company Copyright E 2011, TAOS Inc. r r www.taosinc.com 9 TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 MECHANICAL INFORMATION This SOIC package consists of an integrated circuit mounted on a lead frame and encapsulated with an electrically nonconductive clear plastic compound. The TCS3210 has a 4 × 6 array of photodiodes with a total size of 0.54 mm by 0.8 mm. The photodiodes are 110 μm × 110 μm in size and are positioned on 134 μm centers. PACKAGE D PLASTIC SMALL-OUTLINE NOTE B TOP VIEW 2.12 0.250 BOTTOM VIEW 3.00 0.250 PIN 1 PIN 1 8 0.510 0.330 6 1.27 SIDE VIEW 2.8 TYP CLEAR WINDOW 5.00 4.80 END VIEW 5.3 MAX 0.50 0.25 45 0.88 TYP TOP OF SENSOR DIE A 1.75 1.35 DETAIL A 4.00 3.80 6.20 5.80 0.25 0.19 Pb NOTES: A. B. C. D. 1.27 0.41 0.25 0.10 All linear dimensions are in millimeters. The center of the 0.54-mm by 0.8-mm photo-active area is referenced to the upper left corner tip of the lead frame (Pin 1). Package is molded with an electrically nonconductive clear plastic compound having an index of refraction of 1.55. This drawing is subject to change without notice. Figure 8. Package D — TCS3210 Plastic Small Outline IC Packaging Configuration Copyright E 2011, TAOS Inc. The LUMENOLOGY r Company r r 10 www.taosinc.com TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 MECHANICAL INFORMATION SIDE VIEW Ko 2.11 0.10 [0.083 0.004] 0.292 0.013 [0.0115 0.0005] END VIEW TOP VIEW 1.50 8 0.1 [0.315 0.004] 4 0.1 [0.157 0.004] 2 0.05 [0.079 0.002] 1.75 0.10 [0.069 0.004] B 5.50 0.05 [0.217 0.002] 12 + 0.3 − 0.1 [0.472 + 0.12 − 0.004] A B A DETAIL A Ao NOTES: A. B. C. D. E. F. DETAIL B 6.45 0.10 [0.254 0.004] 5.13 0.10 [0.202 0.004] Bo All linear dimensions are in millimeters [inches]. The dimensions on this drawing are for illustrative purposes only. Dimensions of an actual carrier may vary slightly. Symbols on drawing Ao, Bo, and Ko are defined in ANSI EIA Standard 481−B 2001. Each reel is 178 millimeters in diameter and contains 1000 parts. TAOS packaging tape and reel conform to the requirements of EIA Standard 481−B. This drawing is subject to change without notice. Figure 9. Package D Carrier Tape The LUMENOLOGY r Company Copyright E 2011, TAOS Inc. r r www.taosinc.com 11 TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 MANUFACTURING INFORMATION The Plastic Small Outline IC package (D) has been tested and has demonstrated an ability to be reflow soldered to a PCB substrate. The solder reflow profile describes the expected maximum heat exposure of components during the solder reflow process of product on a PCB. Temperature is measured on top of component. The component should be limited to a maximum of three passes through this solder reflow profile. Table 2. TCS3200, TCS3210 Solder Reflow Profile PARAMETER REFERENCE TCS32x0 Average temperature gradient in preheating Soak time 2.5°C/sec tsoak 2 to 3 minutes Time above 217°C t1 Max 60 sec Time above 230°C t2 Max 50 sec Time above Tpeak −10°C t3 Max 10 sec Tpeak 260° C (−0°C/+5°C) Peak temperature in reflow Temperature gradient in cooling Tpeak Max −5°C/sec Not to scale — for reference only T3 T2 Temperature (C) T1 Time (sec) t3 t2 tsoak t1 Figure 10. TCS3200, TCS3210 Solder Reflow Profile Graph Copyright E 2011, TAOS Inc. The LUMENOLOGY r Company r r 12 www.taosinc.com TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 STORAGE INFORMATION Moisture Sensitivity Optical characteristics of the device can be adversely affected during the soldering process by the release and vaporization of moisture that has been previously absorbed into the package. To ensure the package contains the smallest amount of absorbed moisture possible, each device is baked prior to being dry packed for shipping. Devices are dry packed in a sealed aluminized envelope called a moisture-barrier bag with silica gel to protect them from ambient moisture during shipping, handling, and storage before use. Shelf Life The calculated shelf life of the device in an unopened moisture barrier bag is 12 months from the date code on the bag when stored under the following conditions: Shelf Life: 12 months Ambient Temperature: < 40°C Relative Humidity: < 90% Rebaking of the devices will be required if the devices exceed the 12 month shelf life or the Humidity Indicator Card shows that the devices were exposed to conditions beyond the allowable moisture region. Floor Life The D package has been assigned a moisture sensitivity level of MSL 5a. As a result, the floor life of devices removed from the moisture barrier bag is 24 hours from the time the bag was opened, provided that the devices are stored under the following conditions: Floor Life: 24 hours Ambient Temperature: < 30°C Relative Humidity: < 60% If the floor life or the temperature/humidity conditions have been exceeded, the devices must be rebaked prior to solder reflow or dry packing. Rebaking Instructions When the shelf life or floor life limits have been exceeded, rebake at 60°C for 24 hours. The LUMENOLOGY r Company Copyright E 2011, TAOS Inc. r r www.taosinc.com 13 TCS3200, TCS3210 PROGRAMMABLE COLOR LIGHT-TO-FREQUENCY CONVERTER TAOS099A − AUGUST 2011 PRODUCTION DATA — information in this document is current at publication date. Products conform to specifications in accordance with the terms of Texas Advanced Optoelectronic Solutions, Inc. standard warranty. Production processing does not necessarily include testing of all parameters. LEAD-FREE (Pb-FREE) and GREEN STATEMENT Pb-Free (RoHS) TAOS’ terms Lead-Free or Pb-Free mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TAOS Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br) TAOS defines Green to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material). Important Information and Disclaimer The information provided in this statement represents TAOS’ knowledge and belief as of the date that it is provided. TAOS bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TAOS has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TAOS and TAOS suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. NOTICE Texas Advanced Optoelectronic Solutions, Inc. (TAOS) reserves the right to make changes to the products contained in this document to improve performance or for any other purpose, or to discontinue them without notice. Customers are advised to contact TAOS to obtain the latest product information before placing orders or designing TAOS products into systems. TAOS assumes no responsibility for the use of any products or circuits described in this document or customer product design, conveys no license, either expressed or implied, under any patent or other right, and makes no representation that the circuits are free of patent infringement. TAOS further makes no claim as to the suitability of its products for any particular purpose, nor does TAOS assume any liability arising out of the use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. TEXAS ADVANCED OPTOELECTRONIC SOLUTIONS, INC. PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN CRITICAL APPLICATIONS IN WHICH THE FAILURE OR MALFUNCTION OF THE TAOS PRODUCT MAY RESULT IN PERSONAL INJURY OR DEATH. USE OF TAOS PRODUCTS IN LIFE SUPPORT SYSTEMS IS EXPRESSLY UNAUTHORIZED AND ANY SUCH USE BY A CUSTOMER IS COMPLETELY AT THE CUSTOMER’S RISK. LUMENOLOGY, TAOS, the TAOS logo, and Texas Advanced Optoelectronic Solutions are registered trademarks of Texas Advanced Optoelectronic Solutions Incorporated. Copyright E 2011, TAOS Inc. The LUMENOLOGY r Company r r 14 www.taosinc.com