TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 Complete DDR2, DDR3 and DDR3L Memory Power Solution Synchronous Buck Controller, 2-A LDO, Buffered Reference FEATURES DESCRIPTION • The TPS51916 provides a complete power supply for DDR2, DDR3 and DDR3L memory systems in the lowest total cost and minimum space. It integrates a synchronous buck regulator controller (VDDQ) with a 2-A sink/source tracking LDO (VTT) and buffered low noise reference (VTTREF). The TPS51916 employs D-CAP™ mode coupled with 300 kHz/400 kHz frequencies for ease-of-use and fast transient response or D-CAP2™ mode coupled with higher 500 kHz/670 kHz frequencies to support ceramic output capacitor without an external compensation circuit. The VTTREF tracks VDDQ/2 within excellent 0.8% accuracy. The VTT, which provides 2-A sink/source peak current capabilities, requires only 10-μF of ceramic capacitance. In addition, a dedicated LDO supply input is available. 1 2 • • • Synchronous Buck Controller (VDDQ) – Conversion Voltage Range: 3 V to 28 V – Output Voltage Range: 0.7 V to 1.8 V – 0.8% VREF Accuracy – Selectable Control Architecture – D-CAP™ Mode for Fast Transient Response – D-CAP2™ Mode for Ceramic Output Capacitors – Selectable 300 kHz/ 400 kHz/ 500 kHz/ 670 kHz Switching Frequencies – Optimized Efficiency at Light and Heavy Loads with Auto-skip Function – Supports Soft-Off in S4/S5 States – OCL/OVP/UVP/UVLO Protections – Powergood Output 2-A LDO(VTT), Buffered Reference(VTTREF) – 2-A (Peak) Sink and Source Current – Requires Only 10-μF of Ceramic Output Capacitance – Buffered, Low Noise, 10-mA VTTREF Output – 0.8% VTTREF, 20-mV VTT Accuracy – Support High-Z in S3 and Soft-Off in S4/S5 Thermal Shutdown 20-Pin, 3 mm × 3 mm, QFN Package APPLICATIONS • • The TPS51916 provides rich useful functions as well as excellent power supply performance. It supports flexible power state control, placing VTT at high-Z in S3 and discharging VDDQ, VTT and VTTREF (softoff) in S4/S5 state. Programmable OCL with low-side MOSFET RDS(on) sensing, OVP/UVP/UVLO and thermal shutdown protections are also available. The TPS51916 is available in a 20-pin, 3 mm × 3 mm, QFN package and is specified for ambient temperature from –40°C to 85°C. VIN 5VIN PGND PGND TPS51916 VBST 15 12 V5IN S3 17 S3 S5 16 S5 DDR2/DDR3/DDR3L Memory Power Supplies SSTL_18, SSTL_15, SSTL_135 and HSTL Termination VDDQ DRVH 14 SW 13 DRVL 11 6 VREF 8 REFIN 7 GND PGND 10 PGOOD 20 VDDQSNS 9 VLDOIN 2 VTT 3 19 MODE VTTSNS 1 18 TRIP VTTGND 4 VTTREF 5 Powergood VTT VTTREF UDG-10193 AGND PGND AGND PGND 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. D-CAP, D-CAP2 are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION (1) TA PACKAGE –40°C to 85°C Plastic Quad Flat Pack (QFN) (1) ORDERABLE DEVICE NUMBER TPS51916RUKR TPS51916RUKT PINS 20 OUTPUT SUPPLY MINIMUM QUANTITY Tape and reel 3000 Mini reel 250 For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) VALUE MAX VBST –0.3 36 VBST (3) –0.3 6 SW Input voltage range (2) –5 30 VLDOIN, VDDQSNS, REFIN –0.3 3.6 VTTSNS –0.3 3.6 PGND, VTTGND –0.3 0.3 V5IN, S3, S5, TRIP, MODE –0.3 6 –5 36 DRVH Output voltage range (2) DRVH (3) –0.3 6 VTTREF, VREF –0.3 3.6 VTT –0.3 3.6 DRVL –0.3 6 PGOOD –0.3 Junction temperature range, TJ Storage temperature range, TSTG (1) (2) (3) UNIT MIN –55 V V 6 125 °C 150 °C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to the network ground terminal unless otherwise noted. Voltage values are with respect to the SW terminal. THERMAL INFORMATION THERMAL METRIC TPS51916 QFN (20) PINS θJA Junction-to-ambient thermal resistance 94.1 θJCtop Junction-to-case (top) thermal resistance 58.1 θJB Junction-to-board thermal resistance 64.3 ψJT Junction-to-top characterization parameter 31.8 ψJB Junction-to-board characterization parameter 58.0 θJCbot Junction-to-case (bottom) thermal resistance 5.9 2 Submit Documentation Feedback UNITS °C/W Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 RECOMMENDED OPERATING CONDITIONS MIN Supply voltage 5.5 VBST –0.1 33.5 VBST (1) –0.1 5.5 -3 28 SW (2) –4.5 28 VLDOIN, VDDQSNS, REFIN –0.1 3.5 VTTSNS –0.1 3.5 PGND, VTTGND –0.1 0.1 S3, S5, TRIP, MODE –0.1 5.5 –3 33.5 DRVH Output voltage range TA (1) (2) MAX 4.5 SW Input voltage range TYP V5IN DRVH (1) –0.1 5.5 DRVH (2) –4.5 33.5 VTTREF, VREF –0.1 3.5 VTT –0.1 3.5 DRVL –0.1 5.5 PGOOD –0.1 5.5 Operating free-air temperature –40 85 UNIT V V V °C Voltage values are with respect to the SW terminal. This voltage should be applied for less than 30% of the repetitive period. Copyright © 2010–2012, Texas Instruments Incorporated Submit Documentation Feedback 3 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com ELECTRICAL CHARACTERISTICS over operating free-air temperature range, VV5IN = 5 V, VLDOIN is connected to VDDQ output, VMODE= 0 V, VS3= VS5= 5 V (unless otherwise noted) PARAMETER TEST CONDITION MIN TYP MAX UNIT SUPPLY CURRENT μA IV5IN(S0) V5IN supply current, in S0 TA = 25°C, No load, VS3 = VS5 = 5 V 590 IV5IN(S3) V5IN supply current, in S3 TA = 25°C, No load, VS3 = 0 V, VS5 = 5 V 500 IV5INSDN V5IN shutdown current TA = 25°C, No load, VS3 = VS5 = 0 V 1 μA IVLDOIN(S0) VLDOIN supply current, in S0 TA = 25°C, No load, VS3 = VS5 = 5 V 5 μA IVLDOIN(S3) VLDOIN supply current, in S3 TA = 25°C, No load, VS3 = 0 V, VS5 = 5 V 5 μA IVLDOINSDN VLDOIN shutdown current TA = 25°C, No load, VS3 = VS5 = 0 V 5 μA V μA VREF OUTPUT IVREF = 30 μA, TA = 25°C VVREF Output voltage IVREFOCL Current limit 1.8000 0 μA ≤ IVREF <300 μA, TA = –10°C to 85°C 1.7856 1.8144 0 μA ≤ IVREF <300 μA, TA = –40°C to 85°C 1.7820 1.8180 VVREF = 1.7 V 0.4 0.8 mA VTTREF OUTPUT VVTTREF Output voltage VVDDQSNS/2 |IVTTREF| <100 μA, 1.2 V ≤ VVDDQSNS ≤ 1.8 V 49.2% |IVTTREF| <10 mA, 1.2 V ≤ VVDDQSNS ≤ 1.8 V 49% V 50.8% VVTTREF Output voltage tolerance to VVDDQ IVTTREFOCLSRC Source current limit VVDDQSNS = 1.8 V, VVTTREF= 0 V 10 18 mA IVTTREFOCLSNK Sink current limit VVDDQSNS = 1.8 V, VVTTREF = 1.8 V 10 17 mA IVTTREFDIS VTTREF discharge current TA = 25°C, VS3 = VS5 = 0 V, VVTTREF = 0.5 V 0.8 1.3 mA |IVTT| ≤ 10 mA, 1.2 V ≤ VVDDQSNS ≤ 1.8 V, IVTTREF= 0 A –20 20 |IVTT| ≤ 1 A, 1.2 ≤ VVDDQSNS ≤ 1.8 V, IVTTREF= 0 A –30 30 |IVTT| ≤ 2 A, 1.4 V ≤ VVDDQSNS ≤ 1.8 V, IVTTREF= 0 A –40 40 |IVTT| ≤ 1.5 A, 1.2 V ≤ VVDDQSNS ≤ 1.4 V, IVTTREF= 0 A –40 51% VTT OUTPUT VVTT Output voltage VVTTREF V VVTTTOL Output voltage tolerance to VTTREF IVTTOCLSRC Source current limit VVDDQSNS = 1.8 V, VVTT = VVTTSNS = 0.7 V, IVTTREF= 0 A 2 3 IVTTOCLSNK Sink current limit VVDDQSNS = 1.8V, VVTT = VVTTSNS = 1.1 V, IVTTREF= 0 A 2 3 IVTTLK Leakage current TA = 25°C , VS3 = 0 V, VS5 = 5 V, VVTT = VVTTREF IVTTSNSBIAS VTTSNS input bias current VS3 = 5 V, VS5 = 5 V, VVTTSNS = VVTTREF –0.5 0.0 0.5 IVTTSNSLK VTTSNS leakage current VS3 = 0 V, VS5 = 5 V, VVTTSNS = VVTTREF –1 0 1 IVTTDIS VTT Discharge current TA = 25°C, VS3 = VS5 = 0 V, VVDDQSNS = 1.8 V, VVTT = 0.5 V, IVTTREF= 0 A mV 40 A 5 7.8 μA mA VDDQ OUTPUT VVDDQSNS VDDQ sense voltage VVDDQSNSTOL VDDQSNS regulation voltage tolerance to REFIN VREFIN TA = 25°C IVDDQSNS VDDQSNS input current VVDDQSNS = 1.8 V IREFIN REFIN input current VREFIN = 1.8 V IVDDQDIS VDDQ discharge current VS3 = VS5 = 0 V, VVDDQSNS = 0.5 V, MODE pin pulled down to GND through 47kΩ (Non-tracking) 12 mA IVLDOINDIS VLDOIN discharge current VS3 = VS5 = 0 V, VVDDQSNS = 0.5 V, MODE pin pulled down to GND through 100kΩ (Non-tracking) 1.2 A –3 3 μA 39 –0.1 0.0 mV 0.1 μA SWITCH MODE POWER SUPPLY (SMPS) FREQUENCY VIN = 12 V, VVDDQSNS = 1.8 V, RMODE = 100 kΩ 300 VIN = 12 V, VVDDQSNS = 1.8 V, RMODE = 200 kΩ 400 VIN = 12 V, VVDDQSNS = 1.8 V, RMODE = 1 kΩ 500 VIN = 12 V, VVDDQSNS = 1.8 V, RMODE = 12 kΩ 670 fSW VDDQ switching frequency tON(min) Minimum on time DRVH rising to falling (1) tOFF(min) Minimum off time DRVH falling to rising (1) 4 kHz 60 200 320 450 ns Ensured by design. Not production tested. Submit Documentation Feedback Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 ELECTRICAL CHARACTERISTICS (continued) over operating free-air temperature range, VV5IN = 5 V, VLDOIN is connected to VDDQ output, VMODE= 0 V, VS3= VS5= 5 V (unless otherwise noted) PARAMETER TEST CONDITION MIN TYP MAX Source, IDRVH = –50 mA 1.6 3.0 Sink, IDRVH = 50 mA 0.6 1.5 Source, IDRVL = –50 mA 0.9 2.0 Sink, IDRVL = 50 mA 0.5 1.2 DRVH-off to DRVL-on 10 DRVL-off to DRVH-on 20 UNIT VDDQ MOSFET DRIVER RDRVH RDRVL tDEAD DRVH resistance DRVL resistance Dead time Ω ns INTERNAL BOOT STRAP SW VFBST Forward Voltage VV5IN-VBST, TA = 25°C, IF = 10 mA IVBSTLK VBST leakage current TA = 25°C, VVBST = 33 V, VSW = 28 V 0.1 0.2 V 0.01 1.5 μA μA LOGIC THRESHOLD IMODE VTHMODE MODE source current MODE threshold voltage VIL S3/S5 low-level voltage VIH S3/S5 high-level voltage VIHYST S3/S5 hysteresis voltage IILK S3/S5 input leak current 14 15 16 MODE 0-1 109 129 149 MODE 1-2 235 255 275 MODE 2-3 392 412 432 MODE 3-4 580 600 620 MODE 4-5 829 854 879 MODE 5-6 1202 1232 1262 MODE 6-7 1760 1800 1840 mV 0.5 1.8 V 0.25 –1 0 1 μA SOFT START tSS VDDQ soft-start time Internal soft-start time, CVREF = 0.1 μF, S5 rising to VVDDQSNS > 0.99 × VREFIN 1.1 ms PGOOD COMPARATOR VTHPG VDDQ PGOOD threshold IPG PGOOD sink current tPGDLY PGOOD delay time tPGSSDLY PGOOD start-up delay Copyright © 2010–2012, Texas Instruments Incorporated PGOOD in from higher 106% 108% PGOOD in from lower 90% 92% 94% PGOOD out to higher 114% 116% 118% PGOOD out to lower 82% 84% 86% 3 5.9 0.8 1 VPGOOD = 0.5 V Delay for PGOOD in 110% mA 1.2 ms Delay for PGOOD out, with 100 mV over drive 330 ns CVREF = 0.1 μF, S5 rising to PGOOD rising 2.5 ms Submit Documentation Feedback 5 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com ELECTRICAL CHARACTERISTICS (continued) over operating free-air temperature range, VV5IN = 5 V, VLDOIN is connected to VDDQ output, VMODE= 0 V, VS3= VS5= 5 V (unless otherwise noted) PARAMETER TEST CONDITION MIN TYP MAX 9 10 11 UNIT PROTECTIONS ITRIP TRIP source current TCITRIP TRIP source current temperature coefficient (2) VTRIP VTRIP voltage range VOCL Current limit threshold VOCLN Negative current limit threshold VZC TA = 25°C, VTRIP = 0.4 V 4700 0.2 ppm/°C 3 VTRIP = 3.0 V 360 375 390 VTRIP = 1.6 V 190 200 210 VTRIP = 0.2 V 20 25 30 VTRIP = 3.0 V –390 –375 –360 VTRIP = 1.6 V –210 –200 –190 VTRIP = 0.2 V –30 –25 –20 Wake-up 4.2 4.4 4.5 Shutdown 3.7 3.9 4.1 118% 120% 122% Zero cross detection offset 0 VUVLO V5IN UVLO threshold voltage VOVP VDDQ OVP threshold voltage OVP detect voltage tOVPDLY VDDQ OVP propagation delay With 100 mV over drive VUVP VDDQ UVP threshold voltage UVP detect voltage tUVPDLY VDDQ UVP delay tUVPENDLY VDDQ UVP enable delay VOOB OOB Threshold voltage 68% V mV mV mV 430 66% μA V ns 70% 1 ms 1.2 ms 108% THERMAL SHUTDOWN TSDN (2) 6 Thermal shutdown threshold Shutdown temperature (2) Hysteresis (2) 140 10 °C Ensured by design. Not production tested. Submit Documentation Feedback Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 DEVICE INFORMATION PGOOD MODE TRIP S3 S5 RUK PACKAGE (TOP VIEW) 20 19 18 17 16 VTTSNS 1 15 VBST VLDOIN 2 14 DRVH VTT 3 13 SW VTTGND 4 12 V5IN 11 DRVL 7 8 REFIN 9 10 PGND 6 GND 5 VDDQSNS Thermal Pad VREF VTTREF TPS51916 PIN FUNCTIONS PIN I/O DESCRIPTION NAME NO. DRVH 14 O High-side MOSFET gate driver output. DRVL 11 O Low-side MOSFET gate driver output. GND 7 – Signal ground. MODE 19 I Connect resistor to GND to configure switching frequency, control mode and discharge mode. (See Table 2) PGND 10 – Gate driver power ground. RDS(on) current sensing input(+). PGOOD 20 O Powergood signal open drain output. PGOOD goes high when VDDQ output voltage is within the target range. REFIN 8 I Reference input for VDDQ. Connect to the midpoint of a resistor divider from VREF to GND. Add a capacitor for stable operation. SW 13 S3 17 I S3 signal input. (See Table 1) S5 16 I S5 signal input. (See Table 1) TRIP 18 I Connect resistor to GND to set OCL at VTRIP/8. Output 10-μA current at room temperature, TC = 4700 ppm/°C. VBST 15 I High-side MOSFET gate driver bootstrap voltage input. Connect a capacitor from the VBST pin to the SW pin. VDDQSNS 9 I VDDQ output voltage feedback. Reference input for VTTREF. Also serves as power supply for VTTREF. VLDOIN 2 I Power supply input for VTT LDO. Connect VDDQ in typical application. VREF 6 O 1.8-V reference output. VTT 3 O VTT 2-A LDO output. Need to connect 10 μF or larger capacitance for stability. VTTGND 4 – Power ground for VTT LDO. VTTREF 5 O Buffered VTT reference output. Need to connect 0.22 μF or larger capacitance for stability. VTTSNS 1 I VTT output voltage feedback. V5IN 12 I 5-V power supply input for internal circuits and MOSFET gate drivers. Thermal pad – – Thermal pad. Connect directly to system GND plane with multiple vias. I/O High-side MOSFET gate driver return. RDS(on) current sensing input(–). Copyright © 2010–2012, Texas Instruments Incorporated Submit Documentation Feedback 7 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com FUNCTIONAL BLOCK DIAGRAM VREFIN –32% + UV VREFIN +8/16 % + 20 PGOOD + OV Delay + VREFIN +20% VREFIN –8/16 % VDDQSNS 9 G 15 ?A VREF 6 1.8 V D-CAP: Open, D-CAP2: Short + Control Logic Mode Selection OVP Σ REFIN UVP 19 MODE PWM + + 8 Soft-Start 15 VBST 14 DRVH 10 ?A 13 SW 8R + TRIP 18 OC S5 16 7R S3 17 GND XCON + tON OneShot R NOC + 7 12 V5IN R + 11 DRVL ZC VTT Discharge VDDQ Discharge V5OK VTTREF Discharge VTTREF 5 + 10 PGND 2 VLDOIN + + VTTSNS + 4.4 V/3.9 V 3 VTT 4 VTTGND 1 + TPS51916 UDG-12074 8 Submit Documentation Feedback Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 TYPICAL CHARACTERISTICS 10 V5IN Shutdown Current (µA) V5IN Suppy Current (µA) 1000 800 600 400 200 0 −50 −25 0 25 50 75 Junction Temperature (°C) 100 4 2 −25 0 25 50 75 Junction Temperature (°C) 100 125 Figure 2. V5IN Shutdown Current vs Junction Temperature 10 16 14 8 TRIP Source Current (µA) VLDOIN Suppy Current (µA) 6 0 −50 125 Figure 1. V5IN Supply Current vs Junction Temperature 6 4 2 12 10 8 6 0 −50 −25 0 25 50 75 Junction Temperature (°C) 100 4 −50 125 Figure 3. VLDOIN Supply Current vs Junction Temperature 0 25 50 75 Junction Temperature (°C) 100 125 130 120 110 100 90 80 70 60 −25 0 25 50 75 Junction Temperature (°C) 100 125 Figure 5. OVP/UVP Threshold vs Junction Temperature Copyright © 2010–2012, Texas Instruments Incorporated VDDQSNS Discharge Current (mA) 15 OVP UVP 140 50 −50 −25 Figure 4. Current Sense Current vs Junction Temperature 150 OVP/UVP Threshold (%) 8 12 9 6 3 0 −50 −25 0 25 50 75 Junction Temperature (°C) 100 125 Figure 6. VDDQSNS Discharge Current vs Junction Temperature Submit Documentation Feedback 9 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) 800 8 Switching Frequency (kHz) VTT Discharge Current (mA) 10 6 4 2 700 600 500 400 300 0 −50 −25 0 25 50 75 Junction Temperature (°C) 100 200 125 Figure 7. VTT Discharge Current vs Junction Temperature 500 400 Switching Frequency (kHz) Switching Frequency (kHz) 600 300 12 14 16 Input Voltage (V) 18 20 22 VVDDQ = 1.20 V VVDDQ = 1.35 V VVDDQ = 1.50 V 600 500 400 300 6 8 10 12 14 16 Input Voltage (V) 18 20 200 22 6 8 10 12 14 16 Input Voltage (V) 18 20 22 Figure 10. Switching Frequency vs Input Voltage 800 800 RMODE = 100 kΩ VIN = 12 V 700 700 600 500 400 300 VVDDQ = 1.20 V VVDDQ = 1.35 V VVDDQ = 1.50 V RMODE = 12 kΩ IVDDQ = 5 A 6 8 10 12 14 16 Input Voltage (V) 18 20 Figure 11. Switching Frequency vs Input Voltage Submit Documentation Feedback 22 Switching Frequency (kHz) Switching Frequency (kHz) 10 RMODE = 1 kΩ IVDDQ = 5 A 700 Figure 9. Switching Frequency vs Input Voltage 10 8 800 VVDDQ = 1.20 V VVDDQ = 1.35 V VVDDQ = 1.50 V RMODE = 200 kΩ IVDDQ = 10 A 700 200 6 Figure 8. Switching Frequency vs Input Voltage 800 200 VVDDQ = 1.20 V VVDDQ = 1.35 V VVDDQ = 1.50 V RMODE = 100 kΩ IVDDQ = 10 A VVDDQ = 1.20 V VVDDQ = 1.35 V VVDDQ = 1.50 V 600 500 400 300 200 100 0 0 2 4 6 8 10 12 14 VDDQ Output Current (A) 16 18 20 Figure 12. Switching Frequency vs Load Current Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 TYPICAL CHARACTERISTICS (continued) 800 800 600 500 400 300 200 100 0 600 500 400 300 200 0 2 4 6 8 10 12 14 VDDQ Output Current (A) 16 18 0 20 800 1.55 700 1.54 600 500 400 RMODE = 1 kΩ VIN = 12 V 300 200 VVDDQ = 1.20 V VVDDQ = 1.35 V VVDDQ = 1.50 V 100 0 2 4 6 VDDQ Output Current (A) 8 0 4 6 VDDQ Output Current (A) 8 10 RMODE = 200 kΩ VIN = 12 V 1.53 1.52 1.51 1.50 1.49 1.48 1.47 1.46 1.45 10 0 Figure 15. Switching Frequency vs Load Current 2 4 6 8 10 12 14 VDDQ Output Current (A) 16 18 20 Figure 16. Load Regulation 1.55 0.770 IVDDQ = 0 A IVDDQ = 20 A RMODE = 200 kΩ 1.54 0.765 1.53 VTTREF Voltage (V) VDDQ Output Voltage (V) 2 Figure 14. Switching Frequency vs Load Current VDDQ Output Voltage (V) Switching Frequency (kHz) VVDDQ = 1.20 V VVDDQ = 1.35 V VVDDQ = 1.50 V 100 Figure 13. Switching Frequency vs Load Current 0 RMODE = 1 kΩ VIN = 12 V 700 Switching Frequency (kHz) 700 Switching Frequency (kHz) VVDDQ = 1.20 V VVDDQ = 1.35 V VVDDQ = 1.50 V RMODE = 200 kΩ VIN = 12 V 1.52 1.51 1.50 1.49 1.48 0.760 0.755 0.750 0.745 0.740 1.47 1.46 0.735 1.45 0.730 −10 VVDDQ = 1.5 V 6 8 10 12 14 16 Input Voltage (V) 18 Figure 17. Line Regulation Copyright © 2010–2012, Texas Instruments Incorporated 20 22 −5 0 VTTREF Current (mA) 5 10 Figure 18. VTTREF Load Regulation Submit Documentation Feedback 11 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) 0.695 0.620 0.690 0.615 VTTREF Voltage (V) VTTREF Voltage (V) 0.685 0.680 0.675 0.670 0.665 0.660 0.655 0.610 0.605 0.600 0.595 0.590 0.585 VVDDQ = 1.35 V 0.650 −10 −5 VVDDQ = 1.2 V 0 VTTREF Current (mA) 5 0.580 −10 10 −5 5 10 Figure 20. VTTREF Load Regulation 0.790 0.715 0.780 0.705 0.770 0.695 VTT Voltage (V) VTT Voltage (V) Figure 19. VTTREF Load Regulation 0 VTTREF Current (mA) 0.760 0.750 0.740 0.730 0.685 0.675 0.665 0.655 0.720 0.645 VVDDQ = 1.5 V 0.710 −2.0 −1.5 −1.0 −0.5 0.0 0.5 VTT Current (A) 1.0 1.5 VVDDQ = 1.35 V 0.635 −2.0 −1.5 −1.0 2.0 Figure 21. VTT Load Regulation −0.5 0.0 0.5 VTT Current (A) 1.0 1.5 2.0 Figure 22. VTT Load Regulation 0.640 100 0.630 90 80 70 Efficiency (%) VTT Voltage (V) 0.620 0.610 0.600 0.590 60 50 40 30 0.580 20 0.570 VVDDQ = 1.2 V 0.560 −2.0 −1.5 −1.0 10 −0.5 0.0 0.5 VTT Current (A) 1.0 Figure 23. VTT Load Regulation 12 Submit Documentation Feedback 1.5 2.0 VVDDQ = 1.5 V RMODE = 200 kΩ 0 0.001 0.01 0.1 1 VDDQ Output Current (A) VIN = 20 V VIN = 12 V VIN = 8 V 10 100 Figure 24. Efficiency Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 TYPICAL CHARACTERISTICS (continued) Figure 25. 1.5-V Load Transient Response Figure 26. VTT Load Transient Response Figure 27. 1.5-V Startup Waveforms Figure 28. 1.5-V Startup Waveforms (0.5-V Pre-Biased) Copyright © 2010–2012, Texas Instruments Incorporated Submit Documentation Feedback 13 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) 180 80 180 60 135 60 135 40 90 40 90 20 45 20 45 0 0 0 0 −40 −60 −80 100 −20 −45 −90 −40 −90 −135 −60 −45 VIN = 12 V IVDDQ = 10 A Gain Phase Gain Phase IVTT = −1 A 1000 10000 Frequency (Hz) 100000 −180 1000000 −80 10000 100000 1000000 Frequency (Hz) Gain (dB) Figure 31. VDDQ Bode Plot −180 10000000 Figure 32. VTT Bode Plot (Sink) 80 180 60 135 40 90 20 45 0 0 −20 −45 −40 −90 −60 Gain Phase IVTT = 1 A −80 10000 −135 Phase (°) −20 Gain (dB) 80 Phase (°) Figure 30. 1.5-V Soft-Stop Waveforms (Non-Tracking Discharge) Phase (°) Gain (dB) Figure 29. 1.5-V Soft-Stop Waveforms (Tracking Discharge) −135 −180 10000000 100000 1000000 Frequency (Hz) Figure 33. VTT Bode Plot (Source) 14 Submit Documentation Feedback Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 APPLICATION INFORMATION VDDQ Switch Mode Power Supply Control The TPS51916 supports two SMPS control architectures, D-CAP™ mode and D-CAP2™ mode. Both control modes do not require complex external compensation networks and are suitable for designs with small external components counts. The D-CAP™ mode provides fast transient response with appropriate amount of equivalent series resistance (ESR) on the output capacitors. The D-CAP2™ mode is dedicated for a configuration with very low ESR output capacitors such as multi-layer ceramic capacitors (MLCC). For the both modes, an adaptive ontime control scheme is used to achieve pseudo-constant frequency. The TPS51916 adjusts the on-time (tON) to be inversely proportional to the input voltage (VIN) and proportional to the output voltage (VVDDQ). This makes a switching frequency fairy constant over the variation of input voltage at the steady state condition. These control modes and switching frequencies are selected by the MODE pin described in Table 2. VREF and REFIN, VDDQ Output Voltage The part provides a 1.8-V, ±0.8% accurate, voltage reference from VREF. This output has a 300-μA (max) current capability to drive the REFIN input voltage through a voltage divider circuit. A capacitor with a value of 0.1-μF or larger should be attached close to the VREF terminal. The VDDQ switch-mode power supply (SMPS) output voltage is defined by REFIN voltage, within the range between 0.7 V and 1.8 V, programmed by the resister-divider connected between VREF and GND. (See External Components Selection section.) A few nano farads of capacitance from REFIN to GND is recommended for stable operation. Soft-Start and Powergood Provide a voltage supply to VIN and V5IN before asserting S5 to high. TPS51916 provides integrated VDDQ soft-start functions to suppress in-rush current at start-up. The soft-start is achieved by controlling internal reference voltage ramping up. Figure 34 shows the start-up waveforms. The switching regulator waits for 400μs after S5 assertion. The MODE pin voltage is read in this period. A typical VDDQ ramp up duration is 700μs. TPS51916 has a powergood open-drain output that indicates the VDDQ voltage is within the target range. The target voltage window and transition delay times of the PGOOD comparator are ±8% (typ) and 1-ms delay for assertion (low to high), and ±16% (typ) and 330-ns delay for de-assertion (high to low) during running. The PGOOD start-up delay is 2.5 ms after S5 is asserted to high. Note that the time constant which is composed of the REFIN capacitor and a resistor divider needs to be short enough to reach the target value before PGOOD comparator enabled. S5 VREF VDDQ PGOOD 400 ms 700 ms 1.4 ms UDG-10137 Figure 34. Typical Start-up Waveforms Copyright © 2010–2012, Texas Instruments Incorporated Submit Documentation Feedback 15 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com Power State Control The TPS51916 has two input pins, S3 and S5, to provide simple control scheme of power state. All of VDDQ, VTTREF and VTT are turned on at S0 state (S3=S5=high). In S3 state (S3=low, S5=high), VDDQ and VTTREF voltages are kept on while VTT is turned off and left at high impedance state (high-Z). The VTT output floats and does not sink or source current in this state. In S4/S5 states (S3=S5=low), all of the three outputs are turned off and discharged to GND according to the discharge mode selected by MODE pin. Each state code represents as follow; S0 = full ON, S3 = suspend to RAM (STR), S4 = suspend to disk (STD), S5 = soft OFF. (See Table 1) Table 1. S3/S5 Power State Control STATE S3 S5 VREF VDDQ VTTREF S0 HI HI ON ON ON VTT ON S3 LO HI ON ON ON OFF(High-Z) S4/S5 LO LO OFF OFF(Discharge) OFF(Discharge) OFF(Discharge) MODE Pin Configuration The TPS51916 reads the MODE pin voltage when the S5 signal is raised high and stores the status in a register. A 15-μA current is sourced from the MODE pin during this time to read the voltage across the resistor connected between the pin and GND. Table 2 shows resistor values, corresponding control mode, switching frequency and discharge mode configurations. Table 2. MODE Selection MODE NO. RESISTANCE BETWEEN MODE AND GND (kΩ) CONTROL MODE 7 200 400 6 100 300 5 68 4 47 400 3 33 500 2 22 1 12 0 1 D-CAP™ D-CAP2™ SWITCHING FREQUENCY (kHz) DISCHARGE MODE Tracking 300 Non-tracking 670 670 500 Tracking Discharge Control In S4/S5 state, VDDQ, VTT, and VTTREF outputs are discharged based on the respective discharge mode selected above. The tracking discharge mode discharges VDDQ output through the internal VTT regulator transistors enabling quick discharge operation. The VTT output maintains tracking of the VTTREF voltage in this mode. (Please refer to Figure 29) After 4 ms of tracking discharge operation, the mode changes to non-tracking discharge. The VDDQ output must be connected to the VLDOIN pin in this mode. The non-tracking mode discharges the VDDQ and VTT pins using internal MOSFETs that are connected to corresponding output terminals. The non-tracking discharge is slow compared with the tracking discharge due to the lower current capability of these MOSFETs. (Please refer to Figure 30) 16 Submit Documentation Feedback Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 D-CAP™ Mode Figure 35 shows a simplified model of D-CAP™ mode architecture. VIN VDDQSNS DRVH 9 14 Lx PWM + REFIN Control Logic and Driver 8 R1 VREF R2 DRVL 1.8 V VDDQ ESR 6 + High-Side MOSFET 11 Low-Side MOSFET RLOAD COUT UDG-10136 Figure 35. Simplified D-CAP™ Model The VDDQSNS voltage is compared with REFIN voltage. The PWM comparator creates a set signal to turn on the high-side MOSFET. The gain and speed of the comparator is high enough to maintain the voltage at the beginning of each on-cycle (or the end of each off-cycle) to be substantially constant. The DC output voltage monitored at VDDQ may have line regulation due to ripple amplitude that slightly increases as the input voltage increase. The D-CAP™ mode offers flexibility on output inductance and capacitance selections with ease-of-use without complex feedback loop calculation and external components. However, it does require a sufficient level of ESR that represents inductor current information for stable operation and good jitter performance. Organic semiconductor capacitor(s) or specialty polymer capacitor(s) are recommended. The requirement for loop stability is simple and is described in Equation 1. The 0-dB frequency, f0 defined in Equation 1, is recommended to be lower than 1/3 of the switching frequency to secure proper phase margin. f 1 £ SW f0 = 2p ´ ESR ´ COUT 3 where • • • ESR is the effective series resistance of the output capacitor COUT is the capacitance of the output capacitor fsw is switching frequency Copyright © 2010–2012, Texas Instruments Incorporated (1) Submit Documentation Feedback 17 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com Jitter is another attribute caused by signal-to-noise ratio of the feedback signal. One of the major factors that determine jitter performance in D-CAP™ mode is the down-slope angle of the VDDQSNS ripple voltage. Figure 36 shows, in the same noise condition, that jitter is improved by making the slope angle larger. VVDDQSNS Slope (1) Jitter (2) Slope (2) Jitter 20 mV (1) VREFIN VREFIN +Noise tON tOFF UDG-10139 Figure 36. Ripple Voltage Slope and Jitter Performance For a good jitter performance, use the recommended down slope of approximately 20 mV per switching period as shown in Figure 36 and Equation 2. VOUT ´ ESR ³ 20mV fSW ´ L X where • • 18 VOUT is the VDDQ output voltage LX is the inductance Submit Documentation Feedback (2) Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 D-CAP2™ Mode Operation Figure 37 shows simplified model of D-CAP2™ architecture. VIN CC1 VDDQSNS SW RC1 9 13 CC2 RC2 DRVH 14 G Σ REFIN R1 PWM + 8 LX VDDQ Control Logic and Driver DRVL C OUT R LOAD 11 VREF 6 + R2 1.8 V TPS51916 UDG-10198 Figure 37. Simplified Modulator Using D-CAP2™ Mode The D-CAP2™ mode in the TPS51916 includes an internal feedback network enabling the use of very low ESR output capacitor(s) such as multi-layer ceramic capacitors. The role of the internal network is to sense the ripple component of the inductor current information and combine it with voltage feedback signal. Using RC1=RC2≡RC and CC1=CC2≡CC, 0-dB frequency of the D-CAP2™ mode is given by Equation 3. It is recommended that the 0dB frequency (f0) be lower than 1/3 of the switching frequency to secure the proper phase margin RC ´ CC f £ SW f0 = 2p ´ G ´ L X ´ COUT 3 where • G is gain of the amplifier which amplifies the ripple current information generated by the compensation circuit (3) The typical G value is 0.25, and typical RCCC time constant values for 500 kHz and 670 kHz operation are 23 µs and 14.6 µs, respectively. For example, when fSW=500 kHz and LX=1 µH, COUT should be larger than 88 µF. When selecting the capacitor, pay attention to its characteristics. For MLCC use X5R or better dielectric and consider the derating of the capacitance by both DC bias and AC bias. When derating by DC bias and AC bias are 80% and 50%, respectively, the effective derating is 40% because 0.8 x 0.5 = 0.4. The capacitance of specialty polymer capacitors may change depending on the operating frequency. Consult capacitor manufacturers for specific characteristics. Light-Load Operation In auto-skip mode, the TPS51916 SMPS control logic automatically reduces its switching frequency to improve light-load efficiency. To achieve this intelligence, a zero cross detection comparator is used to prevent negative inductor current by turning off the low-side MOSFET. Equation 4 shows the boundary load condition of this skip mode and continuous conduction operation. ILOAD(LL) = (VIN - VOUT ) ´ VOUT ´ 2 ´ LX VIN 1 fSW Copyright © 2010–2012, Texas Instruments Incorporated (4) Submit Documentation Feedback 19 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com VTT and VTTREF TPS51916 integrates two high performance, low-drop-out linear regulators, VTT and VTTREF, to provide complete DDR2/DDR3/DDR3L power solutions. The VTTREF has a 10-mA sink/source current capability, and tracks ½ of VDDQSNS with ±1% accuracy using an on-chip ½ divider. A 0.22-μF (or larger) ceramic capacitor must be connected close to the VTTREF terminal to ensure stable operation. The VTT responds quickly to track VTTREF within ±40 mV at all conditions, and the current capability is 2 A for both sink and source. A 10-μF (or larger) ceramic capacitor(s) need to be connected close to the VTT terminal for stable operation. To achieve tight regulation with minimum effect of wiring resistance, a remote sensing terminal, VTTSNS, should be connected to the positive node of VTT output capacitor(s) as a separate trace from the high-current line to the VTT pin. (Please refer to the Layout Considerations section for details.) When VTT is not required in the design, following treatment is strongly recommended. • Connect VLDOIN to VDDQ. • Tie VTTSNS to VTT, and remove capacitors from VTT to float. • Connect VTTGND to GND. • Select MODE2, 3, 4 or 5 shown in Table 2 (Select Non-tracking discharge mode). • Maintain a 0.22-µF capacitor connected at VTTREF. • Pull down S3 to GND with 1-kΩ resistance. VIN 5VIN TPS51916 PGND 1 kW S5 12 V5IN VBST 15 17 S3 DRVH 14 VDDQ SW 13 16 S5 DRVL 11 6 VREF 8 REFIN 7 GND PGND 10 PGND PGND PGOOD 20 VDDQSNS 9 VLDOIN 2 VTT 3 19 MODE VTTSNS 1 18 TRIP VTTGND 4 VTTREF 5 AGND PGND Powergood 0.22 mF AGND PGND UDG-12075 Figure 38. Application Circuit When VTT Is Not Required VDDQ Overvoltage and Undervoltage Protection The TPS51916 sets the overvoltage protection (OVP) when VDDQSNS voltage reaches a level 20% (typ) higher than the REFIN voltage. When an OV event is detected, the controller changes the output target voltage to 0 V. This usually turns off DRVH and forces DRVL to be on. When the inductor current begins to flow through the low-side MOSFET and reaches the negative OCL, DRVL is turned off and DRVH is turned on, for a minimum ontime. After the minimum on-time expires, DRVH is turned off and DRVL is turned on again. This action minimizes the output node undershoot due to LC resonance. When the VDDQSNS reaches 0 V, the driver output is latched as DRVH off, DRVL on. VTTREF and VTT are turned off and discharged using the non-tracking discharge MOSFETs regardless of the tracking mode. 20 Submit Documentation Feedback Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 The undervoltage protection (UVP) latch is set when the VDDQSNS voltage remains lower than 68% (typ) of the REFIN voltage for 1 ms or longer. In this fault condition, the controller latches DRVH low and DRVL low and discharges the VDDQ, VTT and VTTREF outputs. UVP detection function is enabled after 1.2 ms of SMPS operation to ensure startup. To release the OVP and UVP latches, toggle S5 or adjust the V5IN voltage down and up beyond the undervoltage lockout threshold. VDDQ Out-of-Bound Operation When the output voltage rises to 8% above the target value, the out-of-bound operation starts. During the out-ofbound condition, the controller operates in forced PWM-only mode. Turning on the low-side MOSFET beyond the zero inductor current quickly discharges the output capacitor. During this operation, the cycle-by-cycle negative overcurrent limit is also valid. Once the output voltage returns to within regulation range, the controller resumes to auto-skip mode. VDDQ Overcurrent Protection The VDDQ SMPS has cycle-by-cycle overcurrent limiting protection. The inductor current is monitored during the off-state using the low-side MOSFET RDS(on), and the controller maintains the off-state when the inductor current is larger than the overcurrent trip level. The current monitor circuit inputs are PGND and SW pins so that those should be properly connected to the source and drain terminals of low-side MOSFET. The overcurrent trip level, VOCTRIP, is determined by Equation 5, where RTRIP is the value of the resistor connected between the TRIP pin and GND, and ITRIP is the current sourced from the TRIP pin. ITRIP is 10 μA typically at room temperature, and has 4700ppm/°C temperature coefficient to compensate the temperature dependency of the low-side MOSFET RDS(on). I VOCTRIP = RTRIP ´ TRIP 8 (5) Because the comparison is done during the off-state, VOCTRIP sets the valley level of the inductor current. The load current OCL level, IOCL, can be calculated by considering the inductor ripple current as shown in Equation 6. æV IOCL = ç OCTRIP ç RDS(on ) è ö I æ ÷ + IND(ripple) = ç VOCTRIP ÷ ç RDS(on ) 2 ø è ö 1 V -V VOUT OUT ÷ + ´ IN ´ ÷ 2 LX fSW ´ VIN ø where • IIND(ripple) is inductor ripple current (6) In an overcurrent condition, the current to the load exceeds the current to the output capacitor, thus the output voltage tends to fall down. Eventually, it crosses the undervoltage protection threshold and shuts down. VTT Overcurrent Protection The LDO has an internally fixed constant overcurrent limiting of 3-A (typ) for both sink and source operation. V5IN Undervoltage Lockout Protection The TPS51916 has a 5-V supply undervoltage lockout protection (UVLO) threshold. When the V5IN voltage is lower than UVLO threshold voltage, typically 3.9 V, VDDQ, VTT and VTTREF are shut off. This is a non-latch protection. Thermal Shutdown The TPS51916 includes an internal temperature monitor. If the temperature exceeds the threshold value, 140°C (typ), VDDQ, VTT and VTTREF are shut off. The state of VDDQ is open, and that of VTT and VTTREF are high impedance (high-Z) at thermal shutdown. The discharge functions of all outputs are disabled. This is a non-latch protection and the operation is restarted with soft-start sequence when the device temperature is reduced by 10°C (typ). Copyright © 2010–2012, Texas Instruments Incorporated Submit Documentation Feedback 21 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 www.ti.com External Components Selection The external components selection is simple in D-CAP™ mode. 1. DETERMINE THE VALUE OF R1 AND R2 The output voltage is determined by the value of the voltage-divider resistor, R1 and R2 as shown in Figure 35. R1 is connected between VREF and REFIN pins, and R2 is connected between the REFIN pin and GND. Setting R1 as 10-kΩ is a good starting point. Determine R2 using Equation 7. R1 R2 = æ ö ç ÷ ç ÷ 1.8 ç ÷ -1 æ IIND(ripple ) ´ ESR ö ÷ ç ÷÷ ç VOUT - ç ç ÷÷ 2 ç è øø è (7) 2. CHOOSE THE INDUCTOR The inductance value should be determined to yield a ripple current of approximately ¼ to ½ of maximum output current. Larger ripple current increases output ripple voltage and improves the signal-to-noise ratio and helps stable operation. LX = 1 IIND(ripple ) ´ fSW IN(max ) - VOUT ´ (V VIN(max ) )´ V OUT = 3 IO(max ) ´ fSW IN(max ) - VOUT ´ (V VIN(max ) )´ V OUT (8) The inductor needs a low direct current resistance (DCR) to achieve good efficiency, as well as enough room above peak inductor current before saturation. The peak inductor current can be estimated in Equation 9. IIND(peak ) = VIN(max ) - VOUT ´ VOUT RTRIP ´ ITRIP 1 + ´ 8 ´ RDS(on ) L ´ fSW VIN(max ) ( ) (9) 3. CHOOSE THE OCL SETTING RESISTANCE, RTRIP Combining Equation 5 and Equation 6, RTRIP can be obtained using Equation 10. RTRIP æ ö æ (V - VOUT ) ö VOUT ÷ ´ RDS(on) ´ 8 ´ ç IOCL - ç IN ÷ ç (2 ´ L X ) ÷ (fSW ´ VIN ) ÷ ç è ø è ø = ITRIP (10) 4. CHOOSE THE OUTPUT CAPACITORS D-CAP™ Mode Organic semiconductor capacitor(s) or specialty polymer capacitor(s) are recommended. Determine ESR to meet small signal stability and recommended ripple voltage. A quick reference is shown in Equation 11 and Equation 12. f 1 £ SW 2p ´ ESR ´ COUT 3 (11) VOUT ´ ESR ³ 20mV fSW ´ L X (12) D-CAP2™ Mode Determine output capacitance to meet small signal stability as shown in Equation 13. 22 Submit Documentation Feedback Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 RC ´ CC f £ SW 2p ´ G ´ L X ´ COUT 3 where • • RC×CC time constant is 23 µs for 500 kHz operation (or 14.6 µs for 670 kHz operation) G = 0.25 (13) TPS51916 Application Circuits V5IN 4.5 V to 5.5 V R2 200 kW R1 100 kW R3 36 kW S5 S3 16 MODE TRIP S3 S5 1 VTTSNS 2 VLDOIN 3 VTT 4 VTTGND 5 VTTREF DRVH 14 U1 TPS51916RUK R6 0W C5 0.1 mF C7 0.1 mF C8 10 mF C9 10 mF C10 10 mF R7 0 W PGND Q1 FDMS8680 L1 0.56 mH VDDQ 1.5 V/20 A SW 13 V5IN 12 PGND VTTREF 0.75 V VIN 8 V to 20 V VBST 15 VDDQSNS PGND 17 REFIN VTTGND 18 GND C1 10 mF 19 VREF VTT 0.75 V/2 A 20 PGOOD PGND 21 PwPad AGND C12 10 mF 6 7 8 9 10 Q2 FDMS8670AS DRVL 11 Q3 FDMS8670AS C6 1 mF C11 330 mF VDDQ_GND R4 10 kW C2 C3 0.22 mF 0.1 mF R5 49 kW C4 10 nF PGND UDG-10195 AGND PGND Figure 39. DDR3, D-CAP™ 400-kHz Application Circuit, Tracking Discharge Table 3. DDR3, D-CAP™ 400-kHz Application Circuit, List of Materials REFERENCE DESIGNATOR QTY SPECIFICATION MANUFACTURE PART NUMBER Taiyo Yuden TMK325BJ106MM C8, C9, C10 3 10 µF, 25 V C11 1 330 µF, 2V, 6 mΩ Panasonic EEFSX0D331XE L1 1 0.56 µH, 21 A, 1.56 mΩ Panasonic ETQP4LR56WFC Q1 1 30 V, 35 A, 8.5 mΩ Fairchild FDMS8680 Q2, Q3 2 30 V, 42 A, 3.5 mΩ Fairchild FDMS8670AS Copyright © 2010–2012, Texas Instruments Incorporated Submit Documentation Feedback 23 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 V5IN 4.5 V to 5.5 V www.ti.com R2 1 kW R1 100 kW R3 36 kW S5 S3 16 MODE TRIP S3 S5 1 VTTSNS 2 VLDOIN DRVH 14 U1 TPS51916RUK VTT 4 VTTGND 5 VTTREF C7 0.1 mF C5 0.1 mF R7 0 W Q1 FDMS8680 V5IN 12 6 7 8 9 10 VTTREF 0.75 V R6 0W C8 10 mF C9 10 mF L1 1 mH PGND VDDQ 1.5 V/10 A SW 13 PGND 3 VIN 8 V to 20 V VBST 15 VDDQSNS PGND 17 REFIN VTTGND 18 GND C1 10 mF 19 VREF VTT 0.75 V/2 A 20 PGOOD PGND 21 PwPad AGND C12 10 mF Q2 FDMS8670AS DRVL 11 C6 1 mF C10 4 x 47 mF VDDQ_GND R4 10 kW C2 C3 0.22 mF 0.1 mF C4 10 nF PGND R5 49.9 kW UDG-10196 AGND PGND Figure 40. DDR3, DCAP-2™ 500-kHz Application Circuit, Tracking Discharge Table 4. DDR3, DCAP-2™ 500-kHz Application Circuit, List of Materials REFERENCE DESIGNATOR QTY SPECIFICATION MANUFACTURE PART NUMBER C8, C9 2 10 µF, 25 V Taiyo Yuden TMK325BJ106MM C10 4 47 µF, 6.3 V TDK C2012X5R0J476M L1 1 1 µH, 18.5 A, 2.3 mΩ NEC Tokin MPC1055L1R0C Q1 1 30 V, 35 A, 8.5 mΩ Fairchild FDMS8680 Q2 1 30 V, 42 A, 3.5 mΩ Fairchild FDMS8670AS 24 Submit Documentation Feedback Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 Layout Considerations Certain issues must be considered before designing a layout using the TPS51916. 2 VLDOIN VTT VTT TPS51916 VIN 3 10 mF VTTGND VTTGND 4 V5IN VTTREF #2 1 mF 5 VOUT DRVL MODE 0.22 mF #1 12 11 19 TRIP #3 PGND 18 10 VREF 6 REFIN 8 GND 7 0.1 mF 10 nF AGND UDG-10197 PGND Figure 41. DC/DC Converter Ground System • • • • VIN capacitor(s), VOUT capacitor(s) and MOSFETs are the power components and should be placed on one side of the PCB (solder side). Other small signal components should be placed on another side (component side). At least one inner system GND plane should be inserted, in order to shield and isolate the small signal traces from noisy power lines. All sensitive analog traces and components such as VDDQSNS, VTTSNS, MODE, REFIN, VREF and TRIP should be placed away from high-voltage switching nodes such as SW, DRVL, DRVH or VBST to avoid coupling. Use internal layer(s) as system GND plane(s) and shield feedback trace from power traces and components. The DC/DC converter has several high-current loops. The area of these loops should be minimized in order to suppress generating switching noise. – The most important loop to minimize the area of is the path from the VIN capacitor(s) through the high and low-side MOSFETs, and back to the negative node of the VIN capacitor(s). Connect the negative node of the VIN capacitor(s) and the source of the low-side MOSFET as close as possible. (Refer to loop #1 of Figure 41) – The second important loop is the path from the low-side MOSFET through inductor and VOUT capacitor(s), and back to source of the low-side MOSFET. Connect the source of the low-side MOSFET and negative node of VOUT capacitor(s) as close as possible. (Refer to loop #2 of Figure 41) – The third important loop is of gate driving system for the low-side MOSFET. To turn on the low-side MOSFET, high current flows from V5IN capacitor through gate driver and the low-side MOSFET, and back to negative node of the capacitor. To turn off the low-side MOSFET, high current flows from gate of the low-side MOSFET through the gate driver and PGND pin, and back to source of the low-side MOSFET. Connect negative node of V5IN capacitor, source of the low-side MOSFET and PGND pin as close as possible. (Refer to loop #3 of Figure 41) Connect negative nodes of the VTTREF output capacitor, VREF capacitor and REFIN capacitor and bottomside resistance of VREF voltage-divider to GND pin as close as possible. The negative node of the VTT Copyright © 2010–2012, Texas Instruments Incorporated Submit Documentation Feedback 25 TPS51916 SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 • • • • • • • • • • 26 www.ti.com output capacitor(s), VTTGND, GND and PGND pins should be connected to system GND plane near the device as shown in Figure 41. Because the TPS51916 controls output voltage referring to voltage across VOUT capacitor, VDDQSNS should be connected to the positive node of VOUT capacitor using different trace from that for VLDOIN. Remember that this sensing potential is the reference voltage of VTTREF. Avoid any noise generative lines. GND pin refers to the negative node of VOUT capacitor. Connect the overcurrent setting resistor from TRIP pin to GND pin and make the connections as close as possible to the device to avoid coupling from a high-voltage switching node. Connect the frequency and mode setting resistor from MODE pin to GND pin ground, and make the connections as close as possible to the device to avoid coupling from a high-voltage switching node. Connections from gate drivers to the respective gate of the high-side or the low-side MOSFET should be as short as possible to reduce stray inductance. Use 0.65 mm (25 mils) or wider trace and via(s) of at least 0.5 mm (20 mils) diameter along this trace. The PCB trace defined as SW node, which connects to the source of the high-side MOSFET, the drain of the low-side MOSFET and the high-voltage side of the inductor, should be as short and wide as possible. VLDOIN should be connected to VOUT with short and wide traces. An input bypass capacitor should be placed as close as possible to the pin with short and wide connections. The negative node of the capacitor should be connected to system GND plane. The output capacitor for VTT should be placed close to the pins with a short and wide connection in order to avoid additional ESR and/or ESL of the trace. VTTSNS should be connected to the positive node of the VTT output capacitor(s) using a separate trace from the high-current power line. When remote sensing is required attach the output capacitor(s) at that point. Also, it is recommended to minimize any additional ESR and/or ESL of ground trace between GND pin and the output capacitor(s). Consider adding a low pass filter (LPF) at VTTSNS in case the ESR of the VTT output capacitor(s) is larger than 2 mΩ. In order to effectively remove heat from the package, prepare a thermal land and solder to the package thermal pad. Wide trace of the component-side copper, connected to this thermal land, helps heat spreading. Numerous vias with a 0.3-mm diameter connected from the thermal land to the internal/solder-side ground plane(s) should be used to help dissipation. The thermal land can be connected to either AGND or PGND but is recommended to be connected to PGND, the system GND plane(s), which has better heat radiation. Submit Documentation Feedback Copyright © 2010–2012, Texas Instruments Incorporated TPS51916 www.ti.com SLUSAE1D – DECEMBER 2010 – REVISED JUNE 2012 Changes from Revision B (AUGUST 2011) to Revision D Page • Added clarity to FUNCTIONAL BLOCK DIAGRAM .............................................................................................................. 8 • Added clarity to Figure 37 ................................................................................................................................................... 19 • Added more information to VTT and VTTREF section. ...................................................................................................... 20 Copyright © 2010–2012, Texas Instruments Incorporated Submit Documentation Feedback 27 PACKAGE OPTION ADDENDUM www.ti.com 23-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS51916RUKR ACTIVE WQFN RUK 20 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS51916RUKT ACTIVE WQFN RUK 20 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 22-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS51916RUKR WQFN RUK 20 3000 330.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 TPS51916RUKT WQFN RUK 20 250 180.0 12.4 3.3 3.3 1.1 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 22-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS51916RUKR WQFN RUK 20 3000 367.0 367.0 35.0 TPS51916RUKT WQFN RUK 20 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated