CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com 12 LVPECL Output, High-Performance Clock Buffer Check for Samples: CDCLVP2106 FEATURES DESCRIPTION • • • The CDCLVP2106 is a highly versatile, low additive jitter buffer that can generate 12 copies of LVPECL clock outputs from two LVPECL, LVDS, or LVCMOS inputs for a variety of communication applications. It has a maximum clock frequency up to 2 GHz. Each buffer block consists of one input that feeds two LVPECL outputs. The overall additive jitter performance is less than 0.1 ps, RMS from 10 kHz to 20 MHz, and overall output skew is as low as 20 ps, making the device a perfect choice for use in demanding applications. 1 2 • • • • • • • • • • • Dual 1:6 Differential Buffer Two Clock Inputs Universal Inputs Can Accept LVPECL, LVDS, LVCMOS/LVTTL 12 LVPECL Outputs Maximum Clock Frequency: 2 GHz Maximum Core Current Consumption: 92 mA Very Low Additive Jitter: <100 fs,rms in 10-kHz to 20-MHz Offset Range 2.375-V to 3.6-V Device Power Supply Maximum Propagation Delay: 550 ps Maximum Within Bank Output Skew: 20 ps LVPECL Reference Voltage, VAC_REF, Available for Capacitive-Coupled Inputs Industrial Temperature Range: –40°C to +85°C Available in 6-mm × 6-mm QFN-40 (RHA) Package ESD Protection Exceeds 2 kV (HBM) APPLICATIONS • • • • The CDCLVP2106 is specifically designed for driving 50-Ω transmission lines. When driving the inputs in single-ended mode, the LVPECL bias voltage (VAC_REF) should be applied to the unused negative input pin. However, for high-speed performance up to 2 GHz, differential mode is strongly recommended. The CDCLVP2106 is characterized for operation from –40°C to +85°C and is available in a QFN-40, 6-mm × 6-mm package. Wireless Communications Telecommunications/Networking Medical Imaging Test and Measurement Equipment VCC The CDCLVP2106 clock buffer distributes two clock inputs (IN0, IN1) to 12 pairs of differential LVPECL clock outputs (OUT0, OUT11) with minimum skew for clock distribution. Each buffer block consists of one input that feeds two LVPECL clock outputs. The inputs can be LVPECL, LVDS, or LVCMOS/LVTTL. VCC VCC VCC VCC INP0 LVPECL INN0 6 6 INP1 LVPECL INN1 VAC_REF[1, 0] VCC 6 6 2 OUTP[5...0] OUTN[5...0] OUTP[11...6] OUTN[11...6] Reference Generator GND GND 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2009–2011, Texas Instruments Incorporated CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. AVAILABLE OPTIONS (1) TA PACKAGED DEVICES FEATURES CDCLVP2106RHAT 40-pin QFN (RHA) package, small tape and reel CDCLVP2106RHAR 40-pin QFN (RHA) package, tape and reel –40°C to +85°C (1) For the most current specifications and package information, see the Package Option Addendum located at the end of this data sheet or refer to our web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS Over operating free-air temperature range (unless otherwise noted). (1) CDCLVP2106 UNIT –0.5 to 4.6 V –0.5 to VCC + 0.5 V –0.5 to VCC + 0.5 V Input current 20 mA Output current 50 mA Specified free-air temperature range (no airflow) –40 to +85 °C TSTG Storage temperature range –65 to +150 °C TJ Maximum junction temperature +125 °C ESD Electrostatic discharge (HBM) 2 kV VCC Supply voltage range (2) VIN Input voltage range VOUT Output voltage range IIN IOUT TA (1) (2) (3) (3) (3) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All supply voltages must be supplied simultaneously. The input and output negative voltage ratings may be exceeded if the input and output clamp-current ratings are observed. RECOMMENDED OPERATING CONDITIONS Over operating free-air temperature range (unless otherwise noted). CDCLVP2106 PARAMETER VCC Supply voltage TA Ambient temperature MIN TYP MAX 2.375 2.50/3.30 3.60 V +85 °C –40 PACKAGE DISSIPATION RATINGS (1) UNIT (2) VALUE PARAMETER θJA θJP (1) (2) (3) 2 Thermal resistance, junction-to-ambient (3) TEST CONDITIONS 4 × 4 VIAS ON PAD UNIT 0 LFM 36.1 °C/W 150 LFM 30.2 °C/W 400 LFM 28.2 °C/W 3.58 °C/W Thermal resistance, junction-to-pad The package thermal resistance is calculated in accordance with JESD 51 and JEDEC 2S2P (high-K board). Connected to GND with 16 thermal vias (0.3-mm diameter). θJP (junction-to-pad) is used for the QFN package, because the primary heat flow is from the junction to the GND pad of the QFN package. Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com ELECTRICAL CHARACTERISTICS: LVCMOS Input (1) At VCC = 2.375 V to 3.6 V and TA = –40°C to +85°C (unless otherwise noted). CDCLVP2106 PARAMETER fIN TEST CONDITIONS TYP MAX UNIT 200 MHz 1.8 V Vth + 0.1 VCC V 0 Vth – 0.1 V 40 μA Input frequency External threshold voltage applied to complementary input Vth Input threshold voltage VIH Input high voltage VIL Input low voltage IIH Input high current VCC = 3.6 V, VIH = 3.6 V IIL Input low current VCC = 3.6 V, VIL = 0 V ΔV/ΔT Input edge rate ICAP Input capacitance (1) MIN 20% to 80% 1.1 –40 1.5 μA V/ns 5 pF Figure 3 and Figure 4 show dc test setup. ELECTRICAL CHARACTERISTICS: Differential Input (1) At VCC = 2.375 V to 3.6 V and TA = –40°C to +85°C (unless otherwise noted). CDCLVP2106 PARAMETER fIN Input frequency TEST CONDITIONS TYP Clock input MAX UNIT 2000 MHz fIN ≤ 1.5 GHz 0.1 1.5 V 1.5 GHz ≤ fIN ≤ 2 GHz 0.2 1.5 V 1.0 VCC – 0.3 V 40 μA VIN, DIFF, PP Differential input peak-peak voltage VICM Input common-mode level IIH Input high current VCC = 3.6 V, VIH = 3.6 V IIL Input low current VCC = 3.6 V, VIL = 0 V ΔV/ΔT Input edge rate ICAP Input capacitance (1) MIN 20% to 80% –40 1.5 μA V/ns 5 pF Figure 5 and Figure 6 show dc test setup. Figure 7 shows ac test setup. Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 3 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com ELECTRICAL CHARACTERISTICS: LVPECL Output (1) At VCC = 2.375 V to 2.625 V and TA = –40°C to +85°C (unless otherwise noted). CDCLVP2106 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VOH Output high voltage VCC – 1.26 VCC – 0.9 V VOL Output low voltage VCC – 1.7 VCC – 1.3 V VOUT, DIFF, PP Differential output peak-peak voltage 0.5 1.35 V VAC_REF Input bias voltage (2) VCC – 1.6 VCC – 1.1 V VIN, DIFF, PP = 0.1V 550 ps VIN, DIFF, PP = 0.3V 550 ps 150 ps 20 ps 25 ps 50 ps tPD Propagation delay tSK,PP Part-to-part skew tSK,O_WB Within bank output skew tSK,O_BB Bank-to-bank output skew tSK,P Pulse skew (with 50% duty cycle input) Random additive jitter (with 50% duty cycle input) tRJIT PSPUR Coupling on differential OUT6 from OUT5 in the frequency spectrum of fOUT, 8 ±(fOUT, 8/2) with synchronous inputs tR/tF Output rise/fall time IEE Supply internal current ICC Output and internal supply current (1) (2) 4 fIN ≤ 2 GHz IAC_REF = 2 mA Both inputs have equal skew Crossing-point-to-crossing-point distortion, fOUT = 100 MHz –50 fOUT = 100 MHz, VIN,SE = VCC, Vth = 1.25 V, 10 kHz to 20 MHz 0.124 ps, RMS fOUT = 100 MHz, VIN,SE = 0.9 V, Vth = 1.1 V, 10 kHz to 20 MHz 0.178 ps, RMS fOUT = 2 GHz, VIN,DIFF,PP = 0.2 V, VICM = 1 V, 10 kHz to 20 MHz 0.061 ps, RMS fOUT = 100 MHz, VIN,DIFF,PP = 0.15 V, VICM = 1 V, 10 kHz to 20 MHz 0.119 ps, RMS fOUT = 100 MHz, VIN,DIFF,PP = 1 V, VICM = 1 V, 10 kHz to 20 MHz 0.104 ps, RMS fOUT,8 = 500 MHz, VIN,DIFF,PP,0 = 0.15 V, VICM, 0 = 1 V, fOUT, 7 = 62.5 MHz, VIN,SE,1 = VCC, Vth, 1 = VCC/2 –45.5 dBc fOUT,8 = 500 MHz, VIN,DIFF,PP,0 = 0.15 V, VICM, 0 = 1 V, fOUT, 7 = 62.5 MHz, VIN,DIFF,PP,1 = 1 V, VICM, 1 = 1 V –47.9 dBc fOUT,8 = 500 MHz, VIN,DIFF,PP,0 = 0.15 V, VICM, 0 = 1 V, fOUT, 7 = 15.625 MHz, VIN,SE,1 = VCC, Vth, 1 = VCC/2 –57.8 dBc fOUT,8 = 500 MHz, VIN,DIFF,PP,0 = 0.15 V, VICM, 0 = 1 V, fOUT, 7 = 15.625 MHz, VIN,DIFF,PP,1 = 1 V, VICM, 1 = 1 V –63.4 dBc 20% to 80% 200 ps Outputs unterminated 92 mA All outputs terminated, 50 Ω to VCC – 2 477 mA Figure 8 and Figure 9 show dc and ac test setup. Internally generated bias voltage (VAC_REF) is for 3.3-V operation only. It is recommended to apply externally generated bias voltage for VCC < 3.0 V. Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com ELECTRICAL CHARACTERISTICS: LVPECL Output (1) At VCC = 3.0 V to 3.6 V and TA = –40°C to +85°C (unless otherwise noted). CDCLVP2106 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VOH Output high voltage VCC – 1.26 VCC – 0.9 V VOL Output low voltage VCC – 1.7 VCC – 1.3 V VOUT, DIFF, PP Differential output peak-peak voltage 0.65 1.35 V VAC_REF Input bias voltage VCC – 1.6 VCC – 1.1 V VIN, DIFF, PP = 0.1V 550 ps VIN, DIFF, PP = 0.3V 550 ps 150 ps 20 ps 25 ps 50 ps tPD Propagation delay tSK,PP Part-to-part skew tSK,O_WB Within bank output skew tSK,O_BB Bank-to-bank output skew tSK,P Pulse skew (with 50% duty cycle input) IAC_REF = 2 mA Both inputs have equal skew Crossing-point-to-crossing-point distortion, fOUT = 100 MHz Random additive jitter (with 50% duty cycle input) tRJIT PSPUR Coupling on differential OUT6 from OUT5 in the frequency spectrum of fOUT, 8 ±(fOUT, 8/2) with synchronous inputs tR/tF Output rise/fall time IEE Supply internal current ICC Output and internal supply current (1) fIN ≤ 2 GHz –50 fOUT = 100 MHz, VIN,SE = VCC, Vth = 1.65 V, 10 kHz to 20 MHz 0.121 ps, RMS fOUT = 100 MHz, VIN,SE = 0.9 V, Vth = 1.1 V, 10 kHz to 20 MHz 0.185 ps, RMS fOUT = 2 GHz, VIN,DIFF,PP = 0.2 V, VICM = 1 V, 10 kHz to 20 MHz 0.077 ps, RMS fOUT = 100 MHz, VIN,DIFF,PP = 0.15 V, VICM = 1 V, 10 kHz to 20 MHz 0.122 ps, RMS fOUT = 100 MHz, VIN,DIFF,PP = 1 V, VICM = 1 V, 10 kHz to 20 MHz 0.105 ps, RMS fOUT,8 = 500 MHz, VIN,DIFF,PP,0 = 0.15 V, VICM, 0 = 1 V, fOUT, 7 = 62.5 MHz, VIN,SE,1 = VCC, Vth, 1 = VCC/2 –48.4 dBc fOUT,8 = 500 MHz, VIN,DIFF,PP,0 = 0.15 V, VICM, 0 = 1 V, fOUT, 7 = 62.5 MHz, VIN,SIFF,PP,1 = 1 V, VICM, 1 = 1 V –52.6 dBc fOUT,8 = 500 MHz, VIN,DIFF,PP,0 = 0.15 V, VICM, 0 = 1 V, fOUT, 7 = 15.625 MHz, VIN,SE,1 = VCC, Vth, 1 = VCC/2 –65.4 dBc fOUT,8 = 500 MHz, VIN,DIFF,PP,0 = 0.15 V, VICM, 0 = 1 V, fOUT, 7 = 15.625 MHz, VIN,DIFF,PP,1 = 1 V, VICM, 1 = 1 V –67.1 dBc 20% to 80% 200 ps Outputs unterminated 92 mA All outputs terminated, 50 Ω to VCC – 2 477 mA Figure 8 and Figure 9 show dc and ac test setup. Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 5 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com PIN CONFIGURATION OUTN7 OUTP7 OUTN6 OUTP6 OUTN5 OUTP5 OUTN4 OUTP4 GND 29 28 27 26 25 24 23 22 21 31 20 VCC OUTP8 32 19 OUTN3 OUTN8 33 18 OUTP3 17 OUTN2 OUTP2 CDCLVP2106 34 OUTN9 35 16 OUTP10 36 15 OUTN1 OUTN10 37 14 OUTP1 13 OUTN0 Thermal Pad (1) 4 5 6 7 8 9 10 VCC VCC VAC_REF0 INN0 INP0 NC VCC VAC_REF1 40 3 OUTP0 11 INN1 12 2 39 INP1 OUTN11 1 38 NC OUTP11 VCC 6 GND VCC OUTP9 (1) 30 RHA PACKAGE QFN-40 (TOP VIEW) Thermal pad must be soldered to ground. Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com PIN DESCRIPTIONS CDCLVP2106 Pin Descriptions TERMINAL NAME TERMINAL NO. VCC 5, 6, 11, 20, 31, 40 Power 2.5-V/3.3-V supplies for the device GND1, GND2 21, 30 Ground Device grounds INP0, INN0 9, 8 Input Differential input pair or single-ended input no. 0 INP1, INN1 2, 3 Input Differential input pair or single-ended input no. 1 OUTP11, OUTN11 38, 39 Output Differential LVPECL output pair no. 11 OUTP10, OUTN10 36, 37 Output Differential LVPECL output pair no. 10 OUTP9, OUTN9 34, 35 Output Differential LVPECL output pair no. 9 OUTP8, OUTN8 32, 33 Output Differential LVPECL output pair no. 8 OUTP7, OUTN7 28, 29 Output Differential LVPECL output pair no. 7 OUTP6, OUTN6 26, 27 Output Differential LVPECL output pair no. 6 OUTP5, OUTN5 24, 25 Output Differential LVPECL output pair no. 5 OUTP4, OUTN4 22, 23 Output Differential LVPECL output pair no. 4 OUTP3, OUTN3 18, 19 Output Differential LVPECL output pair no. 3 OUTP2, OUTN2 16, 17 Output Differential LVPECL output pair no. 2 OUTP1, OUTN1 14, 15 Output Differential LVPECL output pair no. 1 OUTP0 OUTN0 12, 13 Output Differential LVPECL output pair no. 0 VAC_REF0 7 Output Bias voltage output for capacitive coupled input pair no. 0. Do not use VAC_REF at VCC < 3.0 V.If used, it is recommended to use a 0.1-μF capacitor to GND on this pin. The output current is limited to 2 mA. VAC_REF1 4 Output Bias voltage output for capacitive coupled input pair no. 1. Do not use VAC_REF at VCC < 3.0 V. If used, it is recommended to use a 0.1-μF capacitor to GND on this pin. The output current is limited to 2 mA. NC 1, 10 — TYPE DESCRIPTION Do not connect Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 7 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com TYPICAL CHARACTERISTICS At TA = –40°C to +85°C (unless otherwise noted). Differential Output Peak-toPeak Voltage (V) DIFFERENTIAL OUTPUT PEAK-TO-PEAK VOLTAGE vs FREQUENCY 1.0 VCC = 2.375 V TA = -40°C to +85°C VICM = 1 V VIN,DIFF,PP = Min 0.9 0.8 0.7 0.6 0.5 0.4 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Frequency (GHz) Figure 1. Differential Output Peak-to-Peak Voltage (V) DIFFERENTIAL OUTPUT PEAK-TO-PEAK VOLTAGE vs FREQUENCY 1.1 1.2 1.3 1.0 0.9 0.8 0.7 VCC = 3.0 V TA = -40°C to +85°C VICM = 1 V VIN,DIFF,PP = Min 0.6 0.5 0.4 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Frequency (GHz) Figure 2. 8 Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com TEST CONFIGURATIONS This section describes the function of each block for the CDCLVP2106. Figure 3 through Figure 9 illustrate how the device should be setup for a variety of test configurations. IN VIH Vth VIL IN Vth Figure 3. DC-Coupled LVCMOS Input During Device Test VCC VIHmax Vthmax VILmax VIH Vth Vth VIL VIHmin Vthmin VILmin GND Figure 4. Vth Variation over LVCMOS Levels VCC VCC 130 W 130 W CDCLVP2106 LVPECL 82 W 82 W Figure 5. DC-Coupled LVPECL Input During Device Test Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 9 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com 100 W LVDS CDCLVP2106 Figure 6. DC-Coupled LVDS Input During Device Test VCC VCC 82 W 82 W CDCLVP2106 Differential 130 W 130 W Figure 7. AC-Coupled Differential Input to Device Oscilloscope LVPECL 50 W 50 W VCC - 2 V Figure 8. LVPECL Output DC Configuration During Device Test Phase Noise Analyzer LVPECL 150 W 150 W 50 W Figure 9. LVPECL Output AC Configuration During Device Test 10 Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com Figure 10 shows the output voltage and rise/fall time. Output and part-to-part skew are shown in Figure 11. VOH OUTNx VOD VOL OUTPx 80% VOUT,DIFF,PP (= 2 ´ VOD) 20% 0V tR tF Figure 10. Output Voltage and Rise/Fall Time INNx INPx tPLH0 tPLH0 tPLH1 tPLH1 OUTN0 OUTP0 OUTN1 OUTP1 tPLH2 tPLH2 OUTN2 OUTP2 tPLH11 tPLH11 OUTN11 OUTP11 (1) Output skew is calculated as the greater of the following: As the difference between the fastest and the slowest tPLHn (n = 0, 1, 2....11), or as the difference between the fastest and the slowest tPHLn (n = 0, 1, 2....11). (2) Part-to-part skew is calculated as the greater of the following: As the difference between the fastest and the slowest tPLHn (n = 0, 1, 2....11) across multiple devices, or the difference between the fastest and the slowest tPHLn (n = 0, 1, 2....11) across multiple devices. Figure 11. Output and Part-to-Part Skew Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 11 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com APPLICATION INFORMATION Thermal Management Power consumption of the CDCLVP2106 can be high enough to require attention to thermal management. For reliability and performance reasons, the die temperature should be limited to a maximum of +125°C. That is, as an estimate, ambient temperature (TA) plus device power consumption times θJA should not exceed +125°C. The device package has an exposed pad that provides the primary heat removal path to the printed circuit board (PCB). To maximize the heat dissipation from the package, a thermal landing pattern including multiple vias to a ground plane must be incorporated into the PCB within the footprint of the package. The exposed pad must be soldered down to ensure adequate heat conduction out of the package. Figure 12 shows a recommended land and via pattern. 4,0 mm (min) 0,33 mm (typ) 1,0 mm (typ) Figure 12. Recommended PCB Layout Power-Supply Filtering High-performance clock buffers are sensitive to noise on the power supply, which can dramatically increase the additive jitter of the buffer. Thus, it is essential to reduce noise from the system power supply, especially when jitter/phase noise is very critical to applications. Filter capacitors are used to eliminate the low-frequency noise from the power supply, where the bypass capacitors provide the very low impedance path for high-frequency noise and guard the power-supply system against the induced fluctuations. These bypass capacitors also provide instantaneous current surges as required by the device and should have low equivalent series resistance (ESR). To properly use the bypass capacitors, they must be placed very close to the power-supply pins and laid out with short loops to minimize inductance. It is recommended to add as many high-frequency (for example, 0.1-μF) bypass capacitors as there are supply pins in the package. It is recommended, but not required, to insert a ferrite bead between the board power supply and the chip power supply that isolates the high-frequency switching noises generated by the clock driver; these beads prevent the switching noise from leaking into the board supply. Choose an appropriate ferrite bead with very low dc resistance because it is imperative to provide adequate isolation between the board supply and the chip supply, as well as to maintain a voltage at the supply pins that is greater than the minimum voltage required for proper operation. 12 Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com Figure 13 illustrates this recommended power-supply decoupling method. VCC Board Supply Chip Supply Ferrite Bead C 10 mF C 1 mF C 0.1 mF (x6) Figure 13. Power-Supply Decoupling LVPECL Output Termination The CDCLVP2106 is an open emitter for LVPECL outputs. Therefore, proper biasing and termination are required to ensure correct operation of the device and to minimize signal integrity. The proper termination for LVPECL outputs is a 50 Ω to (VCC –2) V, but this dc voltage is not readily available on PCB. Therefore, a Thevenin equivalent circuit is worked out for the LVPECL termination in both direct-coupled (dc) and ac-coupled configurations. These configurations are shown in Figure 14a and b for VCC = 2.5 V and Figure 15a and b for VCC = 3.3 V, respectively. It is recommended to place all resistive components close to either the driver end or the receiver end. If the supply voltage for the driver and receiver is different, ac coupling is required. VCC VCC 250 W 250 W CDCLVP2106 LVPECL 62.5 W 62.5 W (a) Output DC Termination VBB CDCLVP2106 LVPECL 86 W 86 W 50 W 50 W (b) Output AC Termination Figure 14. LVPECL Output DC and AC Termination for VCC = 2.5 V Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 13 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com VCC VCC 130 W 130 W CDCLVP2106 LVPECL 82 W 82 W (a) Output DC Termination VBB CDCLVP2106 150 W LVPECL 150 W 50 W 50 W (b) Output AC Termination Figure 15. LVPECL Output DC and AC Termination for VCC = 3.3 V Input Termination The CDCLVP2106 inputs can be interfaced with LVPECL, LVDS, or LVCMOS drivers. Figure 16 illustrates how to dc couple an LVCMOS input to the CDCLVP2106. The series resistance (RS) should be placed close to the LVCMOS driver; its value is calculated as the difference between the transmission line impedance and the driver output impedance. VIH Vth VIL RS LVCMOS CDCLVP2106 Vth = VIH + VIL 2 Figure 16. DC-Coupled LVCMOS Input to CDCLVP2106 14 Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com Figure 17 shows how to dc couple LVDS inputs to the CDCLVP2106. Figure 18 and Figure 19 describe the method of dc coupling LVPECL inputs to the CDCLVP2106 for VCC = 2.5 V and VCC = 3.3 V, respectively. 100 W LVDS CDCLVP2106 Figure 17. DC-Coupled LVDS Inputs to CDCLVP2106 VCC VCC 250 W 250 W CDCLVP2106 LVPECL 62.5 W 62.5 W Figure 18. DC-Coupled LVPECL Inputs to CDCLVP2106 (VCC = 2.5 V) VCC VCC 130 W 130 W CDCLVP2106 LVPECL 82 W 82 W Figure 19. DC-Coupled LVPECL Inputs to CDCLVP2106 (VCC = 3.3 V) Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 15 CDCLVP2106 SCAS887A – SEPTEMBER 2009 – REVISED AUGUST 2011 www.ti.com Figure 20 and Figure 21 show the technique of ac coupling differential inputs to the CDCLVP2106 for VCC = 2.5–V and VCC = 3.3 V, respectively. It is recommended to place all resistive components close to either the driver end or the receiver end. If the supply voltages of the driver and receiver are different, ac coupling is required. VCC VCC 96 W 96 W CDCLVP2106 Differential 105 W 105 W Figure 20. AC-Coupled Differential Inputs to CDCLVP2106 (VCC = 2.5 V) VCC VCC 82 W 82 W CDCLVP2106 Differential 130 W 130 W Figure 21. AC-Coupled Differential Inputs to CDCLVP2106 (VCC = 3.3 V) REVISION HISTORY NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Original (September, 2009) to Revision A Page • Corrected VIL parameter description in Electrical Characteristics table for LVCMOS input ................................................. 3 • Added footnote (2) to Electrical Characteristics table for LVPECL Output, VCC = 2.375 V to 2.625 V ................................ 4 • Revised descriptions of pins7 and 4 ..................................................................................................................................... 7 • Changed recommended resistor values in Figure 14(a) .................................................................................................... 13 • Changed recommended resistor values in Figure 18 ......................................................................................................... 15 16 Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated Product Folder Link(s): CDCLVP2106 PACKAGE OPTION ADDENDUM www.ti.com 31-Aug-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) CDCLVP2106RHAR ACTIVE VQFN RHA 40 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR CDCLVP2106RHAT ACTIVE VQFN RHA 40 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Feb-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant CDCLVP2106RHAR VQFN RHA 40 2500 330.0 16.4 6.3 6.3 1.5 12.0 16.0 Q2 CDCLVP2106RHAT VQFN RHA 40 250 330.0 16.4 6.3 6.3 1.5 12.0 16.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Feb-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CDCLVP2106RHAR VQFN RHA 40 2500 336.6 336.6 28.6 CDCLVP2106RHAT VQFN RHA 40 250 336.6 336.6 28.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated