PSA2220C-LF PHASE LOCKED LOOP 9939 Via Pasar • San Diego, CA 92126 TEL (858) 621-2700 FAX (858) 621-2722 Rev B2 PHASE NOISE (1 Hz BW, typical) FEATURES • Frequency Range: 2160 - 2280 MHz • Step Size: 1000 KHz • PLL-24H - Style Package APPLICATIONS • Satellite Communication • Fixed Wireless • VALUE 2160 - 2280 PERFORMANCE SPECIFICATIONS Frequency Range UNITS MHz dBc/Hz Phase Noise @ 10 kHz offset (1 Hz BW, typ.) -102 Harmonic Suppression (2nd, typ.) dBc Sideband Spurs (typ.) -20 -65 Power Output 0±3 dBm Load Impedance 50 Step Size 1000 Charge Pump Output Current 3750 Switching Speed (typ., adjacent channel) dBc KHz 5 mSec mSec Operating Temperature Range 5 0 to 70 Package Style PLL-24H Startup Lock Time (typ.) °C POWER SUPPLY REQUIREMENTS Supply Voltage (Vcc, nom.) 5 Vdc Supply Current (Icc, typ.) 30 mA All specifications are typical unless otherwise noted and subject to change without notice. APPLICATION NOTES • AN-107 : How to Solder Z-COMM VCOs / PLLs • AN-200 : Mounting and Grounding of Z-COMM PLLs • AN-201 : PLL Fundamentals AN-202 : PLL Functional Description NOTES: Ref OSC 10MHz. AD chip ADF4106 © Z-Communications, Inc. Page 1 All rights reserved PSA2220C-LF LOW COST - HIGH PERFORMANCE PHASE LOCKED LOOP PAGE 2 VCO TUNING CURVE, typ. 2320 2300 FREQUENCY (MHz) 2280 2260 2240 70 2220 2200 25 2180 0 °c °c °c 2160 2140 2120 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 TUNING VOLTAGE (Vdc) VCO POWER CURVE, typ. OUTPUT POWER (dBm) 4 3 2 1 70 0 25 -1 0 °c °c °c -2 -3 -4 2135 2153 2170 2189 2208 2228 2247 2264 2278 2290 FREQUENCY (MHz) .032 .580 .605 1. SIDE VIEW 0.220 .455 .370 .285 .200 .115 -.026 .000 PHYSICAL DIMENSIONS -.025 24 23 22 21 20 2. .000 PIN 1 .153 .238 .323 .408 .493 1 19 2 18 3 .578 17 TOP 5 SEE DETAIL A .663 4. 5. 16 4 BOTTOM 3. 15 6 14 7 13 .816 .841 8 9 10 11 12 SEE DETAIL B .055 .015 .030 DETAIL B (TYP) DETAIL A © Z-Communications, Inc. TABS RANGE: SEE NOTE 5 (4 PLACES) (8 PLACES) Page 2 The inside radius of all 24 half holes at the perimeter of the board are plated to provide a surface for the attachment of the PLL Module to the PCB. 16 pads are for grounding, 8 pads are for signal interface. The surface of the shield is tin-plated and may be soldered to. The shield’s base metal is cold-rolled steel. The ground plane on the bottom side is ground and attaches to a ground track on the top side of the board as well as to the shield. Unless otherwise noted all dimensions are in inches. Unless otherwise noted all tolerances are as follows: .xxx = ± .010. P1 P2-4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18-24 RF OUTPUT GROUND REFERENCE OSCILLATOR INPUT GROUND CLOCK DATA GROUND LOAD ENABLE GROUND LOCK DETECT VCC GROUND GROUND GROUND NO CONNECTION GROUND Printed in the U.S.A.