PSA0413A-LF PHASE LOCKED LOOP 9939 Via Pasar • San Diego, CA 92126 TEL (858) 621-2700 FAX (858) 621-2722 Rev A1 PHASE NOISE (1 Hz BW, typical) FEATURES • Frequency Range: 370 - 460 MHz • Step Size: 6.25 KHz • PLL - Style Package APPLICATIONS • Telecommunications • Satellite • Telemetry VALUE 370 - 460 PERFORMANCE SPECIFICATIONS Frequency Range UNITS MHz dBc/Hz Phase Noise @ 10 kHz offset (1 Hz BW, typ.) -100 Harmonic Suppression (2nd, typ.) dBc Sideband Spurs (typ.) -10 -55 Power Output 2±3 dBm Load Impedance 50 Step Size 6.25 Charge Pump Output Current 2500 Switching Speed (typ., adjacent channel) Startup Lock Time (typ.) Operating Temperature Range dBc KHz 0.7 mSec 0.7 -40 to 85 mSec °C PLL Package Style POWER SUPPLY REQUIREMENTS Supply Voltage (Vcc, nom.) 5 Vdc Supply Current (Icc, typ.) 35 mA All specifications are typical unless otherwise noted and subject to change without notice. APPLICATION NOTES • AN-107 : How to Solder Z-COMM VCOs / PLLs • AN-200 : Mounting and Grounding of Z-COMM PLLs • AN-201 : PLL Fundamentals AN-202 : PLL Functional Description NOTES: Reference Oscillator Signal: 5 MHz< <100 MHz Frequency Synthesizer: Analog Devices - ADF4113 © Z-Communications, Inc. Prescaler: 8 Page 1 All rights reserved PSA0413A-LF LOW COST - HIGH PERFORMANCE PHASE LOCKED LOOP PAGE 2 VCO TUNING CURVE, typ. FREQUENCY (MHz) 480 470 460 450 440 430 420 410 400 390 380 370 360 350 340 330 320 310 300 85 25 -40 0 0.5 1 1.5 2 2.5 3 3.5 4 °c °c °c 4.5 TUNING VOLTAGE (Vdc) VCO POWER CURVE, typ. OUTPUT POWER (dBm) 5 4 3 85 2 25 1 -40 °c °c °c 0 -1 317 346 367 386 402 417 431 445 458 470 FREQUENCY (MHz) PHYSICAL DIMENSIONS PLL 415-0078 REV. F (DRAWING NOT TO SCALE) 0.140 0.000 0.000 13 12 0.605 14 1 11 -0.025 2 10 0.148 3 9 0.321 4 BOTTOM TABS RANGE: SEE NOTE 5. (4 PLACES) DETAIL A 8 SEE DETAIL A 0.495 5 6 7 .070 0.668 0.580 0.450 0.290 0.130 0.816 -0.025 0.841 SEE DETAIL B © Z-Communications, Inc. P1 RF OUTPUT .032 P2 GROUND P3 REFERENCE OSCILLATOR INPUT P4 CLOCK P5 DATA P6 LOAD ENABLE P7 LOCK DETECT P8 VCC P9 OPTIONAL P10 NO CONNECTION P11-14 GROUND NOTES: 1. THE INSIDE RADIUS OF ALL 14 HALF HOLES AT THE PERIMETER OF THE BOARD ARE PLATED TO PROVIDE A SURFACE FOR THE ATTACHMENT OF THE PLL MODULE TO A PCB, IN 11 LOCATIONS, WITH 3 PADS BEING USED FOR ELECTROMECHANICAL INTERFACE. 14 SOLDER LOCATIONS REQUIRED. 2. THE SURFACE OF THE SHIELD IS TIN PLATED AND MAY BE SOLDERED TO. THE SHIELD'S BASE METAL IS COLD ROLLED STEEL. 3. THE GROUND PLANE IS GROUND AND ATTACHES TO A GROUND TRACK ON THE UPPER SIDE OF THE BOARD AS WELL AS THE SHIELD BY PTH. 4. UNLESS OTHERWISE NOTED ALL DIMENSIONS ARE IN INCHES. 5. UNLESS OTHERWISE NOTED ALL TOLERANCES ARE AS FOLLOWS: TOLERANCES .XXX= ± .010 .015 .030 DETAIL B (TYP) Page 2 Printed in the U.S.A.