A S 11 0 0 D a ta S he e t Serially Interfaced, 8-Digit LED Driver 1 General Description 2 Key Features The AS1100 is an LED driver for 7 segment numeric displays of up to 8 digits. The AS1100 can be programmed via a conventional 4 wire serial interface. The device includes a BCD code-B decoder, a multiplex scan circuitry, segment and display drivers, and a 64 Bit memory. The memory is used to store the LED settings, so that continuous reprogramming is not necessary. Every individual segment can be addressed and updated separately. Only one external resistor is required to set the current through the LED display. Brightness can be controlled either in an analog or digital way. The user can choose the internal code-B decoder to display numeric digits or to address each segment directly. The AS1100 features an extremely low shutdown current of only 20µA and an operational current of less than 500µA. The number of visible digits can be programmed as well. The AS1100 can be reset by software and an external clock can be used. Several test modes support easy debugging. ! 10MHz Serial Interface ! Individual LED Segment Control ! Decode/No-Decode Digit Selection ! 20µA Low-Power Shutdown (Data Retained) ! Extremely low Operating Current 0.5mA in open loop ! Digital and Analog Brightness Control ! Display Blanked on Power-Up ! Drive Common-Cathode LED Display ! Software Reset ! Optional External clock ! 24-pin DIP and SOIC Packages 3 Applications The AS1100 is an ideal solution for Bar-Graph Displays, Industrial Controllers, Panel Meters, LED Matrix Displays and White Goods such as washing machines and dishwasher. The AS1100 is offered in a 24-pin DIP and SOIC packages. Figure 1. Typical Application Diagram – Single Cell to 3.3V Synchronous Boost Converter +5V 19 9.53k VDD 18 ISET DIFG0-DIG3 MOSI 1 DIN µP I/O 12 LOAD SCK 1 CLK 9 GND 8 Digits SEG A-G SEP DP 8 Segments GND 4 8-Digit µP Display www.austriamicrosystems.com Revision 1.33 1 - 17 AS1100 Data Sheet - P i n A s s i g n m e n t s 4 Pin Assignments Figure 2. Pin Assignments (Top View) TOP DIN 1 24 DOUT DIG0 2 23 SEG D DIG4 3 22 SEG DP GND 4 21 SEG E DIG6 5 DIG2 6 AS1100 20 SEG C DIG3 7 19 VDD 18 ISET DIG7 8 17 SEG G GND 9 16 SEG B DIG5 10 15 SEG F 14 SEG A 13 CLK DIG1 11 LOAD12 DIP/SO Pin Descriptions Table 1. Pin Descriptions Pin Name Pin Number DIN 1 DIG 0 – DIG 7 2, 3, 5–8, 10, 11 GND 4, 9 LOAD/CS 12 CLK 13 SEG A–G, DP 14–17, 20–23 ISET 18 VDD 19 DOUT 24 www.austriamicrosystems.com Description Data input. Data is programmed into the 16Bit shift register on the rising CLK edge 8 digit driver lines that sink the current from the common cathode of the display. In shutdown mode the AS1100 switches the outputs to VDD. Both GND pins must be connected. Strobe input. With the rising edge of the LOAD signal the 16 bit of serial data is latched into the register. Clock input. The interface is capable to support clock frequencies up to 10MHz. The serial data is clocked into the internal shift register with the rising edge of the CLK signal. On the DOUT pin the data is applied with the falling edge of CLK. Seven segment driver lines including the decimal point. When a segment is turned off the output is connected to GND. The current into ISET determines the peak current through the segments and therefore the brightness. Positive Supply Voltage (+5V) Serial data output for cascading drivers. The output is valid after 16.5 clock cycles. The output is never set to high impedance. Revision 1.33 2 - 17 AS1100 Data Sheet - A b s o l u t e M a x i m u m R a t i n g s 5 Absolute Maximum Ratings Table 2. Absolute Maximum Ratings Parameter Min Max Units VDD to GND -0.3 +6 V DIN, CLK, LOAD to GND -0.3 +6 V All other Pins to GND -0.3 VDD + 0.3 V VOUT -0.3 7 V Notes Electro Static Discharge at Digital Outputs +500 V Electro Static Discharge at all other pins +1000 V DIG0–DIG7 Sink Current 500 mA SEGA–G, DP Source Current 100 mA Latch up Immunity ±200 mA Narrow Plastic DIP 1066 mW Derate 13.3mW/°C above +70°C Wide SO 941 mW Derate 11.8mW/°C above +70°C Current Continuous Power Dissipation (TA = +85°C) Operating Temperature Ranges (TMIN to TMAX) AS1100xL 0 +70 ºC AS1100xE -40 +85 ºC Storage Temperature Range -65 +150 ºC Package Body Temperature www.austriamicrosystems.com +260 Revision 1.33 ºC The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/JEDEC J-STD020C “Moisture/Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices”. The lead finish for Pb-free leaded packages is matte tin (100% Sn). 3 - 17 AS1100 Data Sheet - E l e c t r i c a l C h a r a c t e r i s t i c s 6 Electrical Characteristics VDD = 5V, RSET = 9.53kΩ±1%, TA = TMIN to TMAX, unlesss otherwise noted. Table 3. Electrical Characteristics Symbol Parameter Conditions Min Typ Max Units VDD Operating Supply Voltage 4.0 5.0 5.5 V IDDSD Shutdown Supply Current 20 50 µA IDD Operating Supply Current 500 µA All segments and decimal point on, ISEG = -40mA Display Scan Rate 8 digits scanned 500 VOUT = 0.65V 320 TA = +25ºC, VOUT = (VDD -1V) -30 All digital inputs at VDD or GND, TA = +25ºC RSET = open circuit fOSC Digit Drive Sink Current IDIGIT 330 800 mA 1300 Hz mA ISEG Segment Drive Source Current ΔISEG Segment Drive Current Matching IDIGIT Digit Drive Source Current Digit off, VDIGIT = (VDD -0.3V) -2 mA ISEG Segment Drive Sink Current Segment off, VSEG = 0.3V 5 mA VIN = 0V or VDD -1 -40 -45 3.0 mA % Logic Inputs IIH, IIL Input Current DIN, CLK, LOAD VIH Logic High Input Voltage VIL Logic Low Input Voltage VOH Output High Voltage DOUT, ISOURCE = -1mA VOL Output Low Voltage DOUT, ISINK = 1.6mA Hysteresis Voltage DIN, CLK, LOAD 1 3.5 µA V 0.8 VDD - 1 V V 0.4 1 V V Timing Characteristics tCP CLK Clock Period 100 ns tCH CLK Pulse Width High 50 ns tCL CLK Pulse Width Low 50 ns tCSH CLK Rise to LOAD Rise Hold Time 0 ns tDS DIN Setup Time 25 ns tDH DIN Hold Time 0 ns tDO Output Data Propagation Delay tLDCK LOAD Rising Edge to Next Clock Rising Edge 50 ns tCSW Minimum LOAD Pulse High 50 ns tDSPD Data-to-Segment Delay www.austriamicrosystems.com CLOAD = 50pF 25 2.25 Revision 1.33 ns ms 4 - 17 AS1100 Data Sheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s 7 Typical Operating Characteristics Figure 4. Segment Current versa RSET 50 50 45 45 40 40 ISEGMENT (mA) . Segment Current (mA) . Figure 3. Segment Driver Capability, VDD = 5V, Logic Level = High 35 30 25 20 15 35 30 25 20 15 10 10 5 5 0 0 0 0.5 1 1.5 2 2.5 3 3.5 4 Voltage below VDD at output (V) www.austriamicrosystems.com 4.5 10 Revision 1.33 RSET (kOhm) 100 5 - 17 AS1100 Data Sheet - D e t a i l e d D e s c r i p t i o n 8 Detailed Description Serial-Addressing Modes Programming of the AS1100 is done via 4 wire serial interface. A programming sequence consists of 16-bit packages. The data is shifted into the internal 16 Bit register with the rising edge of the CLK signal. With the rising edge of the LOAD signal the data is latched into a digital or control register depending on the address. The LOAD signal must go to high after the 16th rising clock edge. The LOAD signal can also come later but just before the next rising edge of CLK, otherwise data would be lost. The content of the internal shift register is applied 16.5 clock cycles later to the DOUT pin. The data is clocked out at the falling edge of CLK. The Bits of the 16Bit-programming package are described in Table 4. The first 4 Bits D15-D12 are don’t care, D11-D8 contain the address and D7-D0 contain the data. The first bit is D15, the most significant bit (MSB). The exact timing is given in Figure 5. Figure 5. Timing Diagram tCSW LOAD tCS tCH tCL tCP tLDCK CLK tDH tDS DIN D14 D15 D1 D0 tDO DOUT Table 4. Serial data format (16bits) D15 D14 D13 D12 X X X X D11 D10 D9 Address D8 D7 MSB D6 D5 D4 D3 Data D2 D1 D0 LSB Digit and Control Registers The AS1100 incorporates 15 registers, which are listed in Table 5. The digit and control registers are selected via the 4Bit address word. The 8 digit registers are realized with a 64bit memory. Each digit can be controlled directly without rewriting the whole contents. The control registers consist of decode mode, display intensity, number of scanned digits, shutdown, display test, and reset/external clock register. Shutdown Mode The AS1100 features a shutdown mode, where it consumes only 20µA current. The shutdown mode is entered via a write to register 0Ch. Then all segment current sources are pulled to ground and all digit drivers are connected to VDD, so that nothing is displayed. All internal digit registers keep the programmed values. The shutdown mode can either be used for power saving or for generating a flashing display by repeatedly entering and leaving the shutdown mode. The AS1100 needs typically 250µs to exit the shutdown mode. During shutdown the AS1100 is fully programmable. Only the display test function overrides the shutdown mode. www.austriamicrosystems.com Revision 1.33 6 - 17 AS1100 Data Sheet - D e t a i l e d D e s c r i p t i o n Initial Power-Up After powering up the system all register are reset, so that the display is blank. The AS1100 starts the shutdown mode. All registers should be programmed for normal operation. The default settings enable only scan of one digit, the internal decoder is disabled, data register and intensity register are set to the minimum value. Decode-Mode Register In the AS1100 a BCD decoder is included. Every digit can be selected via register 09h to be decoded. The BCD code consists of the numbers 0-9, E,H, L,P and -. In register 09h a logic high enables the decoder for the appropriate digit. In case that the decoder is bypassed (logic low) the data Bits D7-D0 correspond to the segment lines of the AS1100. In Table 7 some possible settings for register 09h are shown. Bit D7, which corresponds to the decimal point, is not affected by the settings of the decoder. Logic high means that the decimal point is displayed. In Table 8 the font of the Code B decoder is shown. In Table 9 the correspondence of the register to the appropriate segments of a 7 segment display is shown (see Figure 6). Intensity Control and Interdigit Blanking Brightness of the display can be controlled in an analog way by changing the external resistor (RSET). The current, which flows between VDD and ISET, defines the current that flows through the LEDs. The LED current is 100 times the ISET current. The minimum value of RSET should be 9.53kΩ, which corresponds to 40mA segment current. The brightness of the display can also be controlled digitally via register 0Ah. The brightness can be programmed in 16 steps and is shown in Table 10. An internal pulse width modulator controls the intensity of the display. Scan-Limit Register The scan limit register 0Bh selects the number of digits displayed. When all 8 digits are displayed the update frequency is typically 800Hz. If the number of digits displayed is reduced, the update frequency is reduced as well. The frequency can be calculated using 8fOSC/N, where N is the number of digits. Since the number of displayed digits influences the brightness, the resistor RSET should be adjusted accordingly. The Table 12 shows the maximum allowed current, when fewer than 4 digits are used. To avoid differences in brightness the scan limit register should not be used to blank portions of the display (leading zeros). Table 5. Register address map Address D15-D12 D11 D10 D9 D8 Hex Code No-Op X 0 0 0 0 0xX0 Digit 0 X 0 0 0 1 0xX1 Digit 1 X 0 0 1 0 0xX2 Digit 2 X 0 0 1 1 0xX3 Digit 3 X 0 1 0 0 0xX4 Digit 4 X 0 1 0 1 0xX5 Digit 5 X 0 1 1 0 0xX6 Digit 6 X 0 1 1 1 0xX7 Digit 7 X 1 0 0 0 0xX8 Decode Mode X 1 0 0 1 0xX9 Intensity X 1 0 1 0 0xXA Scan Limit X 1 0 1 1 0xXB Shutdown X 1 1 0 0 0xXC Not used X 1 1 0 1 0xXD Reset and ext. Clock X 1 1 1 0 0xXE Display Test X 1 1 1 1 0xXF Register www.austriamicrosystems.com Revision 1.33 7 - 17 AS1100 Data Sheet - D e t a i l e d D e s c r i p t i o n Table 6. Shutdown Register Format (address (hex) = 0xXC Register Data Mode Address Code (Hex) D7 D6 D5 D4 D3 D2 D1 D0 Shutdown Mode 0xXC X X X X X X X 0 Normal Operation 0xXC X X X X X X X 1 Table 7. Decode-mode Register Examples (address (hex) = 0xX9 Register Data Decode Mode Hex Code D7 D6 D5 D4 D3 D2 D1 D0 No decode for digits 7–0 0 0 0 0 0 0 0 0 0x00 Code B decode for digit 0 No decode for digits 7–1 0 0 0 0 0 0 0 1 0x01 Code B decode for digits 3–0 No decode for digits 7– 4 0 0 0 0 1 1 1 1 0x0F Code B decode for digits 7–0 1 1 1 1 1 1 1 1 0xFF Table 8. Code B font 7-Segment Character Register Data D7* On Segments = 1 D6-D4 D3 D2 D1 D0 0 X 0 0 0 1 X 0 0 2 X 0 3 X 4 DP* A B C D E F G 0 1 1 1 1 1 1 0 0 1 0 1 1 0 0 0 0 0 1 0 1 1 0 1 1 0 1 0 0 1 1 1 1 1 1 0 0 1 X 0 1 0 0 0 1 1 0 0 1 1 5 X 0 1 0 1 1 0 1 1 0 1 1 6 X 0 1 1 0 1 0 1 1 1 1 1 7 X 0 1 1 1 1 1 1 0 0 0 0 8 X 1 0 0 0 1 1 1 1 1 1 1 9 X 1 0 0 1 1 1 1 1 0 1 1 -- X 1 0 1 0 0 0 0 0 0 0 1 E X 1 0 1 1 1 0 0 1 1 1 1 H X 1 1 0 0 0 1 1 0 1 1 1 L X 1 1 0 1 0 0 0 1 1 1 0 P X 1 1 1 0 1 1 0 0 1 1 1 blank X 1 1 1 1 0 0 0 0 0 0 0 Note: The decimal point is set by bit D7 = 1 Table 9. No-decode mode data bits and corresponding segment lines Register Data Corresponding Segment Line www.austriamicrosystems.com D7 D6 D5 D4 D3 D2 D1 D0 DP A B C D E F G Revision 1.33 8 - 17 AS1100 Data Sheet - D e t a i l e d D e s c r i p t i o n Figure 6. Standard 7-segment LED A F B G C E D DP Table 10. Intensity register format (address (hex) = 0xXA) Duty Cycle D7 D6 D5 D4 D3 D2 D1 D0 Hex Code 1/32 (min on) X X X X 0 0 0 0 0xX0 3/32 X X X X 0 0 0 1 0xX1 5/32 X X X X 0 0 1 0 0xX2 7/32 X X X X 0 0 1 1 0xX3 9/32 X X X X 0 1 0 0 0xX4 11/32 X X X X 0 1 0 1 0xX5 13/32 X X X X 0 1 1 0 0xX6 15/32 X X X X 0 1 1 1 0xX7 17/32 X X X X 1 0 0 0 0xX8 19/32 X X X X 1 0 0 1 0xX9 21/32 X X X X 1 0 1 0 0xXA 23/32 X X X X 1 0 1 1 0xXB 25/32 X X X X 1 1 0 0 0xXC 27/32 X X X X 1 1 0 1 0xXD 29/32 X X X X 1 1 1 0 0xXE 31/32 (max on) X X X X 1 1 1 1 0xXF Table 11. Scan -limit register format (address (hex) = 0xXB) Decode Mode Register Data Hex Code D7 D6 D5 D4 D3 D2 D1 D0 Display digit 0 only X X X X X 0 0 0 0xX0 Display digit 0 & 1 X X X X X 0 0 1 0xX1 Display digit 0 1 2 X X X X X 0 1 0 0xX2 Display digit 0 1 2 3 X X X X X 0 1 1 0xX3 Display digit 0 1 2 3 4 X X X X X 1 0 0 0xX4 Display digit 0 1 2 3 4 5 X X X X X 1 0 1 0xX5 Display digit 0 1 2 3 4 5 6 X X X X X 1 1 0 0xX6 Display digit 0 1 2 3 4 5 6 7 X X X X X 1 1 1 0xX7 www.austriamicrosystems.com Revision 1.33 9 - 17 AS1100 Data Sheet - D e t a i l e d D e s c r i p t i o n Display Test Register With the display test register 0Fh all LED can be tested. In the test mode all LEDs are switched on at maximum brightness (duty cycle 31/32). All programming of digit and control registers are maintained. The format of the register is given in Table 13. Table 12. Maximum segment current for 1-, 2-, or 3-digit displays Number of digits Displayed Maximum Segment Current (mA) 1 10 2 20 3 30 Table 13. Display-test register format (address (hex) = 0xXF) Mode Register Data D7 D6 D5 D4 D3 D2 D1 D0 Normal Operation X X X X X X X 0 Display Test Mode X X X X X X X 1 Note: The AS1100 remains in display-test mode until the display-test register is reconfigured for normal operation. No-Op Register (Cascading of AS1100) The no-operation register 00h is used when AS1100s are cascaded in order to support more than 8 digit displays. The cascading must be done in a way that all DOUT are connected to DINof the following AS1100. The LOAD and CLK signals are connected to all devices. For a write operation for example to the fifth device the command must be followed by four no-operation commands. When the LOAD signal finally goes to high all shift registers are latched. The first four devices have got no-operation commands and only the fifth device sees the intended command and updates its register. Reset and external Clock Register This register is addressed via the serial interface. It allows to switch the device to external clock mode (If D0=1 the CLK pin of the serial interface operates as system clock input.) and to apply an external reset (D1). This brings all registers (except reg. E) to default state. For standard operation the register contents should be "00h". Table 14. Reset and External Clock Register (address (hex) = oxXE) Mode Address Register Data code (Hex) D7 D6 D5 D4 D3 D2 D1 D0 Normal Operation, internal clock 0xXE X X X X X X 0 0 Normal Operation, external clock 0xXE X X X X X X 0 1 Reset state, internal clock 0xXE X X X X X X 1 0 Reset state, external clock 0xXE X X X X X X 1 1 www.austriamicrosystems.com Revision 1.33 10 - 17 AS1100 Data Sheet - A p p l i c a t i o n I n f o r m a t i o n 9 Application Information Supply Bypassing and Wiring In order to achieve optimal performance the AS1100 shall be placed very close to the LED display to minimize effects of electromagnetic interference and wiring inductance. Furthermore, it is recommended to connect a 10µF electrolytic and a 0.1µF ceramic capacitor between VDD and GND to avoid power supply ripple. Also, both GNDs must be connected to ground. Selecting RSET Resistor and Using External Drivers The current through the segments is controlled via the external resistor RSET. Segment current is about 100 times the current in ISET. The right values for ISET are given in Table 15. The maximum current the AS1100 can drive is 40mA. If higher currents are needed, external drivers must be used. In that case it is no longer necessary that the AS1100 drives high currents. A recommended value for RSET is 47kΩ. In cases that the AS1100 only drives few digits, Table 12 specifies the maximum currents and RSET must be set accordingly. Refer to absolute maximum ratings to calculate acceptable limits for ambient temperature, segment current, and the LED forward-voltage drop. Table 15. RSET vs segment current and LED forward voltage ISEG (mA) VLED(V) 1.5 2.0 2.5 3.0 3.5 40 12.2kΩ 11.8kΩ 11.0kΩ 10.6kΩ 9.69kΩ 30 17.8kΩ 17.1kΩ 15.8kΩ 15.0kΩ 14.0kΩ 20 29.8kΩ 28.0kΩ 25.9kΩ 24.5kΩ 22.6kΩ 10 66.7kΩ 63.7kΩ 59.3kΩ 55.4kΩ 51.2kΩ 8x8 LED Dot Matrix Driver The example in Figure 7 uses the AS1100 to drive an 8x8 LED dot matrix. The LED columns have common cathode and are connected to the DIG0-7 outputs. The rows are connected to the segment drivers. Each of the 64 LEDs can be addressed separately. The columns are selected via the digits as shown in Table 5. The decode mode register (0xX9) has to be programmed to ‘00000000’ as stated in Table 4. The single LEDs in a column can be addressed as stated in Table 9, where D0 corresponds to segment G and d/ to segment DP. For a multiple digit dot matrix several AS1100 have to be cascaded. www.austriamicrosystems.com Revision 1.33 11 - 17 AS1100 Data Sheet - A p p l i c a t i o n I n f o r m a t i o n Figure 7. Application example as LED dot matrix driver SEG G SEG F SEG G SEG E SEG F SEG D SEG E SEG C SEG D SEG B SEG C SEG A SEG B SEG DP SEG A SEG DP DIG 7 DIG 0 DIG 7 DIG 0 SEG A-G 24 SEP DP VDD 1 SEG A-G 19 24 SEP DP DIP µP 12 1 9 9.53k LOA GND ISET 18 1 GND 9 4 19 DIP 12 CLK VDD 1 9.53k LOA CLK GND ISET 18 GND 4 Cascading Drivers The AS1100 can be cascaded as well. The DOUT pin must be connected to the DIN pin of the following AS1100. Table 16. Package thermal resistance data Package Thermal Resistance (θJA) 24 Narrow DIP +75ºC/W 24 Wide SO +85ºC/w Maximum Junction Temperature (TJ) = +150ºC Maximum Ambient Temperature (TA) = +85ºC www.austriamicrosystems.com Revision 1.33 12 - 17 AS1100 Data Sheet - A p p l i c a t i o n I n f o r m a t i o n Computing Power Dissipation The upper limit for power dissipation (PD) for the AS1100 is determined from the following equation: PD = (VDD x 0.5mA) + (VDD - VLED)(DUTY x ISEG x N) (EQ 1) Where: VDD = supply voltage DUTY = duty cycle set by intensity register N = number of segments driven (worst case is 8) VLED = LED forward voltage ISEG = segment current set by RSET Dissipation Example: ISEG = 40mA, N = 8, DUTY = 31/32, VLED = 1.8V at 40mA, VDD = 5.25V PD = 5.25V(0.5mA) + (5.25V - 1.8V)(31/32 x 40mA x 8) = 1.07W Thus, for a PDIP package θJA = +75°C/W (from Table 13), the maximum allowed ambient temperature TA is given by: TJ,MAX = TA + PD x θJA = 150°C = TA +1.07W x 75°C/W. Where: TA = +69.7°C. The TA limit for SO Packages in the dissipation example above is +59.0°C. www.austriamicrosystems.com Revision 1.33 13 - 17 AS1100 Data Sheet - P a c k a g e D r a w i n g s a n d M a r k i n g s 10 Package Drawings and Markings The device is available in a SOIC-24 package and PDIP-24 package . Figure 8. SOIC-24 package Diagram Table 17. SOIC-24 package Dimensions Symbol Min Max Symbol Min Max A 2.44 2.64 H 10.11 10.51 A1 0.10 0.30 h 0.31 0.71 A2 2.24 2.44 J 0.53 0.73 B 0.36 0.46 K C 0.23 0.32 L 0.51 1.01 D 15.20 15.40 R 0.63 0.89 E 7.40 7.60 ZD e www.austriamicrosystems.com α 1.27 BSC Revision 1.33 7° BSC 0.66 REF 0° 8° 14 - 17 AS1100 Data Sheet - P a c k a g e D r a w i n g s a n d M a r k i n g s Figure 9. PDIP-24 package Diagram Table 18. PDIP-24 package Dimensions Symbol Min Typ A Max Symbol Min 4.32 E1 6.35 Max 6.60 6.86 e1 2.54 BSC 0.56 eA 7.62 BSC 1.52 1.65 L 3.18 3.43 1.14 1.27 1.40 α 0° 15° C 0.20 0.25 0.30 N D 31.62 31.75 31.88 Q1 E 7.62 8.26 Q2 A1 0.380 B 0.38 0.46 B1 1.40 b1 S www.austriamicrosystems.com Revision 1.33 24 1.40 1.52 1.65 3.30 1.78 1.91 2.03 15 - 17 AS1100 Data Sheet - O r d e r i n g I n f o r m a t i o n 11 Ordering Information Table 19. Ordering Information Part AS1100PL Temp Range 0ºC to +70ºC Package Plastic DIP 24-pin Delivery Form Tubes AS1100WL 0ºC to +70ºC SOIC 24-pin Tubes AS1100PE -40ºC to +85ºC Plastic DIP 24-pin Tubes AS1100WE -40ºC to +85ºC SOIC 24-pin Tubes AS1100WL-T 0ºC to +70ºC SOIC 24-pin Tape & Reel -40ºC to +85ºC SOIC 24-pin Tape & Reel AS1100WE-T www.austriamicrosystems.com Revision 1.33 16 - 17 AS1100 Data Sheet Copyrights Copyright © 1997-2007, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. Disclaimer Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG A-8141 Schloss Premstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com Revision 1.33 17 - 17