SGX-41F SOLID STATE RELAY 4 AMPS 48 TO 400 VRMS FEATURES • • • • • • • • Photo isolation Up to 800V blocking voltage Both zero cross or random turn-on High surge capability Built-in snubber UL, CUR file E43203 SCR or Triac Output Circuitry RoHS compliant INPUT Type Control Voltage Range Turn On Voltage Turn Off Voltage Max. Input Current Max. Reverse Voltage 1D 2D 3 to 15 VDC 15 to 32 VDC 3 VDC max. 15 VDC max. 1 VDC min. 1 VDC min. 40 mA at 15 VDC 20 mA at 32 VDC -15 VDC -32 VDC OUTPUT Type Output Voltage Range Blocking Voltage Max. Leakage Current (off) 240 380 48 to 264 VAC 48 to 400 VAC 600 Vpk 800 Vpk 5 mA 5 mA Max. Voltage Drop (at rated current) 1.7 VRMS Min. Load Current 100 mA Max. Turn-On Time Random Turn On (DC input): 1 ms Zero Cross Turn On (DC input): 1/2 cycles + 1 ms AC Input: 20 ms Max. Turn-Off Time DC Input: 1/2 cycle + 1 ms AC Input: 40 ms Min. Off-State (dv/dt) Triac: 200 V/us / SCR: 500 V/us GENERAL Dielectric Strength 4000 Vrms min. (at 50/60 Hz, 1 min.) Insulation Resistance 1000 Min. (at 500 VDC) Ambient Temperature Operating: -30°C (-22°F) to 80°C (176°F) Storage: -30°C (122°F) to 100°C (212°F) Termination PCB Weight 15g 3/29/06W SGX-41F RELAY ORDERING DATA SGX-41F 1D MODEL 240 INPUT VOLTAGE 1D: 3 TO 15 Vdc 2D: 15 to 32 Vdc A 4 OPERATING VOLTAGE RANGE LOAD TYPE 240:48 TO 264 Vac 380: 48 to 400 Vac A: AC LOAD Z LOAD CURRENT 4: 4A S ZERO CROSS OUTPUT DEVICE OR RANDOM Z: Zero cross turn on P: Random turn on S: SCR Nil: Triac G PACKAGE G: epoxy MECHANICAL DATA Outline Dimensions PC Board Layout 1.724MAX [43.8] .374MAX [9.5] Ø0.047 [1.2] .200 [5.08] 1.043MAX [26.5MAX] .118MAX [3.0] .100 [2.54] 0.200 [5.1] .370 [9.4] Ø.039 [1.0] .201 [5.1] 1.100 [27.9] .098MAX [2.5] .701 [17.8] 1.098 [27.9] 0.700 [17.8] Wiring Diagram -4 +3 2 1 Load Input control Power supply Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" INSTALLATION PRECAUTIONS 1. 1. Before connecting a load that generates a high surge current, such as a lamp load to the SSR, make sure that the SSR can withstand the surge current of the load. 2. The product data sheet shows the non-repetitive peak value of the surge current that flows through the SSR. Normally, use 1/2 of the non-repetitive peak surge current as the standard value. If a surge current exceeding that value is expected, connect a quick-blowing fuse to protect the SSR. When mounting the relays side by side, provide a space equivalent to the width of a single SSR between two adjacent SSRs. Otherwise, reduce the load current flow to 1/2 to 1/3 of the rated current. 3/29/06W SGX-41F CHARACTERISTIC CURVES Figure 1 Maximum load current vs. ambient temperature 3/29/06W