BeRex BIF1 50-800 MHz Internally Matched IF Amplifier Device Features 44dBm Output IP3 at 10dBm/tone at 70MHz 15.1dB Gain at 250MHz 20.9dBm P1dB at 250MHz Highly Reliable InGaP/GaAs HBT Technology Temperature Compensation Circuit patent Over Voltage Protection Circuit patent SOT-89 Surface Mount Package 50 ohm Cascadeable Lead-free/Green/RoHS compliant Application: commercial, space, military wireless system Electrical Specifications (Ta = 25C, Vs = 5V) Parameters Test Conditions Frequency Range Gain S11 S22 OIP3 P1dB Ic Vc dG/dT Rth 70 MHz 140 MHz 250 MHz 500 MHz 70 MHz 140 MHz 250 MHz 500 MHz 70 MHz 140 MHz 250 MHz 500 MHz 70 MHz 140 MHz 250 MHz 500 MHz 70 MHz 140 MHz 250 MHz 500 MHz Vc = 5.0V Thermal Resistance Min 50 14.2 14.2 14.1 14.0 42.0 38.0 38.5 35.5 19.0 19.8 19.9 20.0 95 Typ 15.2 15.2 15.1 15.0 -18.0 -17.0 -18.0 -18.0 -16.0 -17.0 -16.0 -15.0 44.0 42.0 40.5 37.5 20.0 20.8 20.9 21.0 105 5.0 -0.001 50 Max Unit 800 16.2 16.2 16.1 16.0 MHz dB dB dB dBm dBm 115 mA V dB/C C/W Typical test conditions unless otherwise noted. 1. Device performance is measured on BeRex evaluation board at 25C, 50 ohm system 2. OIP3 measured with two tones at an output power of 10dBm/tone separated by 1MHz. http: //www.berex.com BeRex BIF1 Absolute Maximum Ratings Parameters Rating Operating Case temperature Storage Temperature Junction Temperature Supply Voltage/Current ( Above this voltage, device goes to protection mode) Input RF Power -40 to +85C -55 to +155C +220C 7V/180mA 23dBm Operation of this device above any of these parameters may result in permanent damage. [I-V Characteristics] [Generic SOT89 Evaluation Board] 16 0 14 0 +2 5C BeRex -30C 12 0 Icc [mA] +8 5C Evaluation Board 10 0 80 60 40 MMIC Innovator 20 0 2 3 4 5 *Dielectric constant is 4.2 *RF pattern width 52mil *31mil thick FR4 PCB 6 Vcc [V] Application Circuit: 50 - 800 MHz Schematic Diagram C3 C4 BOM C5 +5V L1 RFin C2 C1 BIF1 RFout Tolerance C1 8200pF ±5% C2 8200pF ±5% C3 100pF ±5% C4 1000pF ±5% C5 10uF ±20% L1 1200nH 5% http: //www.berex.com BeRex BIF1 Typical Device Data S-parameters (Vc=5V, Ic=105mA, T=25C) Typical Performance (Vdevice = 5.0V, Ic = 108mA, Ta = 25C) Freq MHz 70 140 250 S21 S11 S22 P1 OIP3 NF dB dB dB dBm dBm dB 15.2 -18 -16 20.0 44.0 4.2 15.2 -18 -17 20.8 42.0 4.3 15.1 -18 -16 20.9 40.5 4.3 500 15.0 -18 -15 21.0 40.0 4.4 800 14.7 -19 -13 20.7 37.5 4.5 http: //www.berex.com BeRex BIF1 Typical Performance (V device = 4.7 V, Ic = 87 mA, Ta = 25 ℃) Freq MHz 70 140 250 500 800 S21 S11 S22 P1 OIP3 NF dB dB dB dBm dBm dB 15.2 -18.6 -11.9 18.9 42.5 4.2 15.2 -20.4 -14.6 19.5 38.5 4.3 15.1 -21.6 -15.6 19.4 41 4.3 15 -23.3 -14.1 19.8 38 4.4 14.8 -25.6 -10.9 19.3 34.9 4.5 Typical Performance (V device = 4.5 V, Ic = 79 mA, Ta = 25 ℃) Freq MHz 70 140 250 500 800 S21 dB 15.1 15.1 15.0 14.9 14.9 S11 dB -18.7 -20.7 -22 -23.8 -26.1 S22 dB -11.8 -14.5 -15.4 -14 -10.8 P1 dBm 18.6 19.3 19.4 19.3 19.4 OIP3 dBm 42.4 42.0 38.0 38.0 36.0 NF dB 4.2 4.3 4.3 4.4 4.5 Typical Performance (V device = 4 V, Ic = 60 mA, Ta = 25 ℃) Freq MHz 70 140 250 500 800 S21 S11 S22 P1 OIP3 NF dB dB dB dBm dBm dB 15 -19.4 -11.7 16.4 37.5 15.1 -21.8 -14.2 16.9 35.5 15 -23.4 -15.1 17 36.5 14.8 -25.5 -13.7 16.9 34.5 14.6 -28 -10.6 16.7 32.2 4.2 4.3 4.3 4.4 4.5 Typical Performance (V device = 3.5 V, Ic = 40 mA, Ta = 25 ℃) Freq MHz 70 140 250 500 800 S21 S11 S22 P1 OIP3 NF dB dB dB dBm dBm dB 14.8 -20.7 -11.4 13.4 34 14.9 -24.4 -13.6 14.1 31.5 14.8 -26.9 -14.4 14.2 30.5 14.6 -30 -13.1 13.6 29.5 14.4 -32.1 -10.2 13.3 28.6 4.2 4.3 4.3 4.4 4.5 http: //www.berex.com BeRex BIF1 Device Performance OIP3 F1=140, F2=141MHz F1=70, F2=71MHz -30C +25C +80C 50 50 45 45 40 OIP3 [dBm] OIP3 [dBm] +25C 35 30 25 +80C 40 35 30 25 20 20 8 9 10 11 12 13 14 8 9 10 11 12 Po,tot [dBm ] Po,tot [dBm ] F1=250, F2=251MHz F1=500, F2=501MHz +25C -30C +25C +80C 50 50 45 45 OIP3 [dBm] OIP3 [dBm] -30C 40 35 30 -30C 13 14 +80C 40 35 30 25 25 20 20 8 9 10 11 12 13 14 Po,tot [dBm ] 8 9 10 11 12 13 14 Po,tot [dBm ] F1=800, F2=801MHz +25C -30C +80C 50 OIP3 [dBm] 45 40 35 30 25 20 8 9 10 11 12 13 14 Po,tot [dBm ] http: //www.berex.com BeRex BIF1 ACPR F=140MHz, IS-95A, 9CH-FWD 885KHz Offset F=70MHz, IS-95A, 9CH-FWD 885KHz Offset -10 -10 +25℃ +25℃ -20 -20 -30℃ +85℃ ACPR [dBc] ACPR [dBc] -30℃ -30 -40 -50 -60 -30 +85℃ -40 -50 -60 -70 -70 -80 -80 7 8 9 10 11 12 13 14 15 7 8 9 10 Po [dBm ] 12 13 14 15 14 15 Po [dBm ] F=250MHz, IS-95A, 9CH-FWD 885KHz Offset F=500MHz, IS-95A, 9CH-FWD 885KHz Offset -10 -10 +25℃ -20 +25℃ -20 -30℃ -30℃ -30 +85℃ ACPR [dBc] ACPR [dBc] 11 -40 -50 -60 -70 -30 +85℃ -40 -50 -60 -70 -80 -80 7 8 9 10 11 12 13 14 15 Po [dBm ] 7 8 9 10 11 12 13 Po [dBm ] ACLR F=800MHz, IS-95A, 9CH-FWD 885KHz Offset -10 +25℃ ACPR [dBc] -20 -30℃ +85℃ -30 -40 -50 -60 -70 -80 7 8 9 10 11 12 13 14 15 Po [dBm ] http: //www.berex.com BeRex BIF1 S-Parameters(S11/S22) S22 over Temperature S11 over Temperature +25C -30C +25C +85C +85C -5 S22 [dB] . -10 -15 -20 -25 -10 -15 -20 0 200 400 600 800 0 200 Freq [MHz] 400 600 800 Freq [MHz] Gain Flatness S21 over Temperature +25C -30C +85C 18 S21 [dB] S11 [dB] . -30C 16 14 12 0 100 200 300 400 500 600 700 800 Freq [MHz] http: //www.berex.com BeRex BIF1 Package Outline Dimension Suggested PCB Land Pattern and PAD Layout PCB Land Pattern PCB Mounting 0.40 1.30 0.40 Ø0.40 0.40 0.75 1.20 2.00 1.20 0.50 1.20 1.20 2.80 1.50 1.00 0.65 Note : All dimension are in millimeters Visit http://www.berex.com for PCB layout http: //www.berex.com BeRex BIF1 Tape & Reel Packaging information: SOT89 Tape Width (mm): 12 Reel Size (inches): 7 Device Cavity Pitch (mm): 8 Devices Per Reel: 1000 Lead plating finish 100% Tin Matte finish. (All BeRex products undergoes a 1 hour, 150 degree C, Anneal bake to eliminate thin whisker growth concerns) MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1C Passes <2000V Human Body Model (HBM) JEDEC Standard JESD22-A114B MSL Rating: Standard: Level 1 at +265C convection reflow JEDEC Standard J-STD-020 NATO CAGE code: 2 N 9 6 F NOTICE BeRex Corporation reserves the right to make changes of product specification or to discontinue product at any time without notice. http: //www.berex.com