BeRex BIF3 50-800 MHz Internally Matched IF Amplifier Device Features 44dBm Output IP3 at 8dBm/tone at 70MHz 20.3dB Gain at 70MHz 24.5dBm P1dB at 140MHz Highly Reliable InGaP/GaAs HBT Technology Over Voltage Protection Circuit patent SOT-89 Surface Mount Package 50 ohm Cascadeable Lead-free/Green/RoHS compliant Application: commercial, space, military wireless system Electrical Specifications (Ta = 25C, Vs = 5V) Parameters Test Conditions Frequency Range Gain S11 S22 OIP3 P1dB Ic Vc dG/dT Rth 70 MHz 140 MHz 250 MHz 500 MHz 70 MHz 140 MHz 250 MHz 500 MHz 70 MHz 140 MHz 250 MHz 500 MHz 70 MHz 140 MHz 250 MHz 500 MHz 70 MHz 140 MHz 250 MHz 500 MHz Vc = 5.0V Thermal Resistance Min 50 19.3 19.2 18.9 18.0 42.0 39.5 38.5 38.5 22.5 23.5 23.5 23.2 75 Typ 20.3 20.2 19.9 19.0 -19.0 -18.0 -15.0 -11.0 -16.0 -17.0 -16.0 -13.0 44.0 41.5 40.5 40.5 23.5 24.5 24.5 24.2 85 5.0 -0.004 45 Max Unit 800 21.3 21.2 20.9 20.0 MHz dB dB dB dBm dBm 97 mA V dB/C C/W Typical test conditions unless otherwise noted. 1. Device performance is measured on BeRex evaluation board at 25C, 50 ohm system 2. OIP3 measured with two tones at an output power of 8dBm/tone separated by 1MHz. http: //www.berex.com BeRex BIF3 Absolute Maximum Ratings Parameters Rating Operating Case temperature Storage Temperature Junction Temperature Supply Voltage/Current ( Above this voltage, device goes to protection mode) Input RF Power -40 to +85C -55 to +155C +220C 7V/140mA 23dBm Operation of this device above any of these parameters may result in permanent damage. [I-V Characteristics] [Generic SOT89 Evaluation Board] 140 +25C -30C 120 +85C BeRex Icc [mA] 100 80 Evaluation Board 60 40 20 MMIC Innovator 0 2 3 4 5 6 *Dielectric constant is 4.2 *RF pattern width 52mil *31mil thick FR4 PCB Vcc [V] Application Circuit: 50 - 800 MHz Schematic Diagram C3 C4 BOM C5 +5V L1 RFin C2 C1 BIF3 RFout Tolerance C1 8200pF ±5% C2 8200pF ±5% C3 100pF ±5% C4 1000pF ±5% C5 10uF ±20% L1 680nH 5% http: //www.berex.com BeRex BIF3 Typical Device Data S-parameters (Vc=5V, Ic=80mA, T=25C) http: //www.berex.com BeRex BIF3 Typical Performance (Vdevice = 5.0V, Ic = 85mA, Ta = 25C) Freq MHz 70 140 250 S21 S11 S22 P1 OIP3 NF dB dB dB dBm dBm dB 20.3 -19 -16 23.5 44 5.1 20.2 -18 -17 24.5 41.5 5.2 19.9 -15 -16 24.5 40.5 5.2 500 19.0 -11 -13 24.2 40.5 5.3 800 17.9 -8 -11 24.0 39.5 5.3 Typical Performance (V device = 4.7 V, Ic = 64 mA, Ta = 25 ℃) Freq MHz 70 140 250 500 800 S21 S11 S22 P1 OIP3 NF dB dB dB dBm dBm dB 20.1 -27.2 -13.1 22.9 35.0 5.1 19.9 -24.6 -12.6 23.5 38.5 5.2 19.7 -16.8 -13 23.3 39.5 5.2 18.9 -11.3 -12.5 23.3 36.5 5.3 17.6 -9.3 -9.7 22.7 35.3 5.3 Typical Performance (V device = 4.5 V, Ic = 54 mA, Ta = 25 ℃) Freq MHz 70 140 250 500 800 S21 S11 S22 P1 OIP3 NF dB dB dB dBm dBm dB 20.2 -18.8 -14.1 22.1 34.5 5.1 20.2 -19 -16 23.0 37.5 5.2 19.8 -16.1 -15.1 23.1 34.5 5.2 18.7 -11.8 -11.8 22.6 35.5 5.3 17.5 -9.2 -9.6 22.2 34.5 5.3 Typical Performance (V device = 4 V, Ic = 28 mA, Ta = 25 ℃) Freq MHz 70 140 250 500 800 S21 S11 S22 P1 OIP3 NF dB dB dB dBm dBm dB 19.5 -18.4 -12.3 20.7 35 5.1 19.4 -18.5 -13.8 21.2 29 5.2 19.1 -15.8 -13.5 21.2 27.5 5.2 18.1 -11.5 -11.3 20.7 25.5 5.3 16.8 -8.9 -9.4 13.5 31 5.3 http: //www.berex.com BeRex BIF3 Device Performance OIP3 F1=140, F2=141MHz F1=70, F2=71MHz -30C +25C +80C 50 50 45 45 OIP3 [dBm] OIP3 [dBm] +25C 40 35 30 +80C 40 35 30 25 25 20 20 8 9 10 11 12 13 8 14 9 10 11 12 Po,tot [dBm ] Po,tot [dBm ] F1=250, F2=251MHz F1=500, F2=501MHz +25C -30C +80C +25C 50 50 45 45 OIP3 [dBm] OIP3 [dBm] -30C 40 35 30 -30C 13 14 +80C 40 35 30 25 25 20 20 8 9 10 11 12 13 14 Po,tot [dBm ] 8 9 10 11 12 13 14 Po,tot [dBm ] F1=800, F2=801MHz +25C -30C +80C 50 OIP3 [dBm] 45 40 35 30 25 20 8 9 10 11 12 13 14 Po,tot [dBm ] http: //www.berex.com BeRex BIF3 ACPR F=140MHz, IS-95A, 9CH-FWD 885KHz Offset F=70MHz, IS-95A, 9CH-FWD 885KHz Offset -10 -10 +25℃ +25℃ -20 -20 -30℃ ACPR [dBc] ACPR [dBc] -30℃ -30 +85℃ -40 -50 -60 -30 +85℃ -40 -50 -60 -70 -70 -80 -80 7 8 9 10 11 12 13 14 15 7 8 9 10 Po [dBm ] 12 13 14 15 Po [dBm ] F=250MHz, IS-95A, 9CH-FWD 885KHz Offset F=500MHz, IS-95A, 9CH-FWD 885KHz Offset -10 -10 +25℃ +25℃ -20 -20 -30℃ -30 +85℃ ACPR [dBc] ACPR [dBc] 11 -40 -50 -60 -70 -30℃ +85℃ -30 -40 -50 -60 -70 -80 -80 7 9 11 13 15 Po [dBm ] 7 9 11 13 15 Po [dBm ] ACLR F=800MHz, IS-95A, 9CH-FWD 885KHz Offset -10 +25℃ -20 ACPR [dBc] -30℃ -30 +85℃ -40 -50 -60 -70 -80 7 9 11 13 15 Po [dBm ] http: //www.berex.com BeRex BIF3 S-Parameters(S11/S22) S22 over Temperature S11 over Temperature +25C -30C +85C +25C +85C -5 S22 [dB] . -5 -10 -15 -10 -15 -20 -20 0 200 400 600 0 800 200 400 600 800 Freq [MHz] Freq [MHz] Gain Flatness S21 over Temperature +25C -30C +85C 22 S21 [dB] S11 [dB] . -30C 20 18 16 0 100 200 300 400 500 600 700 800 Freq [MHz] http: //www.berex.com BeRex BIF3 Package Outline Dimension Suggested PCB Land Pattern and PAD Layout PCB Land Pattern PCB Mounting 0.40 1.30 0.40 Ø0.40 0.40 0.75 1.20 2.00 1.20 0.50 1.20 1.20 2.80 1.50 1.00 0.65 Note : All dimension are in millimeters Visit http://www.berex.com for PCB layout http: //www.berex.com BeRex BIF3 Tape & Reel Packaging information: SOT89 Tape Width (mm): 12 Reel Size (inches): 7 Device Cavity Pitch (mm): 8 Devices Per Reel: 1000 Lead plating finish 100% Tin Matte finish. (All BeRex products undergoes a 1 hour, 150 degree C, Anneal bake to eliminate thin whisker growth concerns) MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1C Passes <2000V Human Body Model (HBM) JEDEC Standard JESD22-A114B MSL Rating: Standard: Level 1 at +265C convection reflow JEDEC Standard J-STD-020 NATO CAGE code: 2 N 9 6 F NOTICE BeRex Corporation reserves the right to make changes of product specification or to discontinue product at any time without notice. http: //www.berex.com