TI LM26

LM26
LM26 SOT-23, +/-3C Accurate, Factory Preset Thermostat
Literature Number: SNIS115Q
LM26
SOT-23, ±3°C Accurate, Factory Preset Thermostat
General Description
The LM26 is a precision, single digital-output, low-power thermostat comprised of an internal reference, DAC, temperature
sensor and comparator. Utilizing factory programming, it can
be manufactured with different trip points as well as different
digital output functionality. The trip point (TOS) can be preset
at the factory to any temperature in the range of −55°C to
+110°C in 1°C increments. The LM26 has one digital output
(OS/OS/US/US), one digital input (HYST) and one analog
output (VTEMP). The digital output stage can be preset as either open-drain or push-pull. In addition, it can be factory
programmed to be active HIGH or LOW. The digital output
can be factory programmed to indicate an over temperature
shutdown event (OS or OS) or an under temperature shutdown event (US or US). When preset as an overtemperature
shutdown (OS) it will go LOW to indicate that the die temperature is over the internally preset TOS and go HIGH when the
temperature goes below (TOS–THYST). Similarly, when preprogrammed as an undertemperature shutdown (US) it will
go HIGH to indicate that the temperature is below TUS and go
LOW when the temperature is above (TUS+THYST). The typical
hysteresis, THYST, can be set to 2°C or 10°C and is controlled
by the state of the HYST pin. A VTEMP analog output provides
a voltage that is proportional to temperature and has a
−10.82mV/°C output slope.
Available parts are detailed in the ordering information. For
other part options, contact a National Semiconductor Distributor or Sales Representative for information on minimum
order qualification. The LM26 is currently available in a 5-lead
SOT-23 package.
Applications
■ Microprocessor Thermal Management
■ Appliances
■ Portable Battery Powered Systems
■
■
■
■
■
Fan Control
Industrial Process Control
HVAC Systems
Remote Temperature Sensing
Electronic System Protection
Features
■ Internal comparator with pin programmable 2°C or 10°C
hysteresis
■ No external components required
■ Open Drain or push-pull digital output; supports CMOS
■
■
■
■
■
■
logic levels
Internal temperature sensor with VTEMP output pin
VTEMP output allows after-assembly system testing
Internal voltage reference and DAC for trip-point setting
Currently available in 5-pin SOT-23 plastic package
Excellent power supply noise rejection
UL Recognized Component
Key Specifications
■ Power Supply Voltage
2.7V to 5.5V
■ Power Supply Current
40µA (max)
20µA (typ)
■ Hysteresis Temperature
2°C or 10°C (typ)
Temperature Trip Point Accuracy
Temperature Range
LM26CIM
−55°C to +110°C
±3°C (max)
+120°C
±4°C (max)
LM26CIM5-TPA Simplified Block Diagram and Connection Diagram
10132301
The LM26CIM5-TPA has a fixed trip point of 85°C.
For other trip point and output function availability,
please see ordering information or contact National Semiconductor.
© 2011 National Semiconductor Corporation
101323
www.national.com
LM26 SOT-23, ±3°C Accurate, Factory Preset Thermostat
September 9, 2009
LM26
Ordering Information
For more detailed information on the suffix meaning see the part number template at the end of the Electrical Characteristics
Section. Contact National Semiconductor for other set points and output options.
Order Number
Bulk Rail
3000 Units in Tape &
Reel
Top Mark
NS Package
Number
Trip Point Setting
Output Function
LM26CIM5-BPB
LM26CIM5X-BPB
TBPB
MA05B
−45°C
Open Drain US
LM26CIM5-DPB
LM26CIM5X-DPB
TDPB
MA05B
−25°C
Open Drain US
LM26CIM5-HHD
LM26CIM5X-HHD
THHD
MA05B
0°C
Push Pull US
LM26CIM5-NPA
LM26CIM5X-NPA
TNPA
MA05B
45°C
Open Drain OS
LM26CIM5-PHA
LM26CIM5X-PHA
TPHA
MA05B
50°C
Open Drain OS
LM26CIM5-RPA
LM26CIM5X-RPA
TRPA
MA05B
65°C
Open Drain OS
LM26CIM5-SHA
LM26CIM5X-SHA
TSHA
MA05B
70°C
Open Drain OS
LM26CIM5-SPA
LM26CIM5X-SPA
TSPA
MA05B
75°C
Open Drain OS
LM26CIM5-TPA
LM26CIM5X-TPA
TTPA
MA05B
85°C
Open Drain OS
LM26CIM5-VHA
LM26CIM5X-VHA
TVHA
MA05B
90°C
Open Drain OS
LM26CIM5-VPA
LM26CIM5X-VPA
TVPA
MA05B
95°C
Open Drain OS
LM26CIM5-XHA
LM26CIM5X-XHA
TXHA
MA05B
100°C
Open Drain OS
LM26CIM5-XPA
LM26CIM5X-XPA
TXPA
MA05B
105°C
Open Drain OS
LM26CIM5-YHA
LM26CIM5X-YHA
TYHA
MA05B
110°C
Open Drain OS
LM26CIM5-YPA
LM26CIM5X-YPA
TYPA
MA05B
115°C
Open Drain OS
LM26CIM5-ZHA
LM26CIM5X-ZHA
TZHA
MA05B
120°C
Open Drain OS
Connection Diagram
10132302
Pin Descriptions
Pin
Number
Pin
Name
1
HYST
Hysteresis control, digital input
GND for 10°C or V+ for 2°C
2
GND
Ground, connected to the back side of the die
through lead frame.
System GND
3
VTEMP
Analog output voltage proportional to
temperature
Leave floating or connect to a high impedance node.
4
V+
Supply input
2.7V to 5.5V with a 0.1µF bypass capacitor. For PSRR
information see Section Titled NOISE CONSIDERATIONS.
OS
Overtemperature Shutdown open-drain active
low thermostat digital output
5
Function
Connection
Controller interrupt, system or power supply shutdown; pull-up
resistor ≥ 10kΩ
OS
Overtemperature Shutdown push-pull active
high thermostat digital output
US
Undertemperature Shutdown open-drain active
System or power supply shutdown; pull-up resistor ≥ 10kΩ
low thermostat digital output
US
Undertemperature Shutdown push-pull active
high thermostat digital output
Controller interrupt, system or power supply shutdown
System or power supply shutdown
Note: pin 5 functionality and trip point setting are programmed during LM26 manufacture.
www.national.com
2
Input Voltage
Input Current at any pin (Note 2)
Package Input Current (Note 2)
Package Dissipation at TA = 25°C
(Note 3)
Soldering Information
SOT23 Package
Vapor Phase (60 seconds)
Infrared (15 seconds)
6.0V
5mA
20mA
Operating Ratings
500mW
−65°C to + 150°C
2500V
250V
(Note 1)
TMIN ≤ TA ≤ TMAX
Specified Temperature Range
−55°C ≤ TA ≤ +125°C
LM26CIM
Positive Supply Voltage (V+)
Maximum VOUT
215°C
220°C
+2.7V to +5.5V
+5.5V
LM26 Electrical Characteristics
The following specifications apply for V+ = 2.7VDC to 5.5VDC, and VTEMP load current = 0µA unless otherwise specified. Boldface
limits apply for TA = TJ = TMIN to TMAX; all other limits TA = TJ = 25°C unless otherwise specified.
Symbol
Parameter
Conditions
Typical
(Note 6)
LM26CIM
Limits
(Note 7)
Units
(Limits)
±3
°C (max)
±4
°C (max)
Temperature Sensor
Trip Point Accuracy (Includes VREF, DAC, -55°C ≤ TA ≤ +110°C
Comparator Offset, and Temperature
+120°C
Sensitivity errors)
Trip Point Hysteresis
HYST = GND
HYST =
V+
VTEMP Output Temperature Sensitivity
VTEMP Temperature Sensitivity Error to
Equation:
VO = (−3.479×10−6×(T−30)2)
+ (−1.082×10−2×(T−30)) + 1.8015V
11
2
°C
−10.82
mV/°C
−30°C ≤ TA ≤ 120°C,
2.7V ≤ V+ ≤ 5.5V
−55°C ≤ TA ≤ 120°C,
4.5V ≤ V+ ≤ 5.5V
TA = 30°C
VTEMP Load Regulation
VTEMP Line Regulation
IS
Source ≤ 1 μA
+2.7V ≤
≤ +5.5V,
−30°C ≤ TA ≤ +120°C
Supply Current
±3
°C (max)
±3
°C (max)
±2.5
°C (max)
0.070
Sink ≤ 40 μA
V+
°C
mV
0.7
−0.2
mV (max)
mV/V
16
20
40
µA (max)
µA (max)
0.001
1
µA (max)
0.4
V (max)
0.8 × V+
V (min)
V+ − 1.5
V (min)
Digital Output and Input
IOUT(“1”)
Logical “1” Output Leakage Current
(Note 9)
V+ = +5.0V
IOUT = +1.2mA and
VOUT(“0”)
VOUT(“1”)
Logical “0” Output Voltage
V+≥2.7V; IOUT = +3.2mA
and V+≥4.5V; (Note 8)
Logical “1” Push-Pull Output Voltage
ISOURCE = 500µA, V+ ≥
2.7V
ISOURCE = 800µA, V
≥4.5V
+
VIH
HYST Input Logical ”1“ Threshold
Voltage
0.8 × V+
V (min)
VIL
HYST Input Logical ”0“ Threshold
Voltage
0.2 × V+
V (max)
3
www.national.com
LM26
Storage Temperature
ESD Susceptibility (Note 4)
Human Body Model
Machine Model
Absolute Maximum Ratings (Note 1)
LM26
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: When the input voltage (VI) at any pin exceeds the power supply (VI < GND or VI > V+), the current at that pin should be limited to 5mA. The 20mA
maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 5mA to four. Under normal
operating conditions the maximum current that pins 2, 4 or 5 can handle is limited to 5mA each.
Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX (maximum junction temperature), θJA (junction to
ambient thermal resistance) and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PD = (TJMAX–TA) / θJA or the number
given in the Absolute Maximum Ratings, whichever is lower. For this device, TJMAX = 150°C. For this device the typical thermal resistance (θJA) of the different
package types when board mounted follow:
Package Type
θJA
SOT23-5, MA05B
250°C/W
Note 4: The human body model is a 100pF capacitor discharge through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor discharged
directly into each pin.
Note 5: See the URL ”http://www.national.com/packaging/“ for other recommendations and methods of soldering surface mount devices.
Note 6: Typicals are at TJ = TA = 25°C and represent most likely parametric norm.
Note 7: Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
Note 8: Care should be taken to include the effects of self heating when setting the maximum output load current. The power dissipation of the LM26 would
increase by 1.28mW when IOUT = 3.2mA and VOUT = 0.4V. With a thermal resistance of 250°C/W, this power dissipation would cause an increase in the die
temperature of about 0.32°C due to self heating. Self heating is not included in the trip point accuracy specification.
Note 9: The 1µA limit is based on a testing limitation and does not reflect the actual performance of the part. Expect to see a doubling of the current for every
15°C increase in temperature. For example, the 1nA typical current at 25°C would increase to 16nA at 85°C.
Part Number Template
The series of digits labeled xyz in the part number LM26CIM-xyz, describe the set point value and the function of the output as
follows:
The place holders xy describe the set point temperature as shown in the following table.
x (10x)
y (1x)
Temperature (°C)
x (10x)
A
-
−5
N
y (1x)
Temperature (°C)
N
4
B
-
−4
P
P
5
C
-
−3
R
R
6
D
-
−2
S
S
7
E
-
−1
T
T
8
F
-
−0
V
V
9
H
H
0
X
-
10
J
J
1
Y
-
11
K
K
2
Z
-
12
L
L
3
The value of z describes the assignment/function of the output as shown in the following table:
Active-Low/High
Open-Drain/ PushPull
OS/US
Value of z
0
0
0
A
Active-Low, Open-Drain, OS output
0
0
1
B
Active-Low, Open-Drain, US output
1
1
0
C
Active-High, Push-Pull, OS output
1
1
1
D
Active-High, Push-Pull, US output
Digital Output Function
For example:
•
•
the part number LM26CIM5-TPA has TOS = 85°C, and programmed as an active-low open-drain overtemperature shutdown
output.
the part number LM26CIM5-FPD has TUS = −5°C, and programmed as an active-high, push-pull undertemperature shutdown
output.
Active-high open-drain and active-low push-pull options are available, please contact National Semiconductor for more information.
www.national.com
4
LM26
Functional Description
LM26 OPTIONS
10132313
10132312
LM26-_ _B
LM26-_ _A
10132314
10132315
LM26-_ _C
LM26-_ _D
FIGURE 1. Output Pin Options Block Diagrams
3.
The LM26 can be factory programmed to have a trip point
anywhere in the range of −55°C to +110°C.
Applications Hints
AFTER-ASSEMBLY PCB TESTING
The LM26's VTEMP output allows after-assembly PCB testing
by following a simple test procedure. Simply measuring the
VTEMP output voltage will verify that the LM26 has been assembled properly and that its temperature sensing circuitry is
functional. The VTEMP output has very weak drive capability
that can be overdriven by 1.5mA. Therefore, one can simply
force the VTEMP voltage to cause the digital output to change
state, thereby verifying that the comparator and output circuitry function after assembly. Here is a sample test procedure that can be used to test the LM26CIM5-TPA which has
an 85°C trip point.
1. Turn on V+ and measure VTEMP. Then calculate the
temperature reading of the LM26 using the equation:
VO = (−3.479×10−6×(T−30)2) + (−1.082×10−2×(T
−30)) + 1.8015V
Observe that OS is high.
Drive VTEMP to ground.
Observe that OS is now low.
Release the VTEMP pin.
Observe that OS is now high.
A.
B.
C.
D.
E.
Observe that OS is high.
Drive VTEMP voltage down gradually.
When OS goes low, note the VTEMP voltage.
VTEMPTrig = VTEMP at OS trigger (HIGH->LOW)
Calculate Ttrig using Equation 2.
A.
Gradually raise VTEMP until OS goes HIGH. Note
VTEMP.
Calculate THYST using Equation 2.
4.
5.
B.
VTEMP LOADING
The VTEMP output has very weak drive capability (1 µA source,
40 µA sink). So care should be taken when attaching circuitry
to this pin. Capacitive loading may cause the VTEMP output to
oscillate. Simply adding a resistor in series as shown in Figure
2 will prevent oscillations from occurring. To determine the
value of the resistor follow the guidelines given in Table 1. The
same value resistor will work for either placement of the resistor. If an additional capacitive load is placed directly on the
LM26 output, rather than across CLOAD, it should be at least
a factor of 10 smaller than CLOAD.
(1)
or
2.
A.
B.
C.
D.
E.
(2)
Verify that the temperature measured in step one is
within (±3°C + error of reference temperature sensor) of
the ambient/board temperature. The ambient/board
temperature (reference temperature) should be
measured using an extremely accurate calibrated
temperature sensor.
5
www.national.com
LM26
mented to a surface. The temperature that the LM26 is sensing will be within about +0.06°C of the surface temperature to
which the LM26's leads are attached to.
This presumes that the ambient air temperature is almost the
same as the surface temperature; if the air temperature were
much higher or lower than the surface temperature, the actual
temperature measured would be at an intermediate temperature between the surface temperature and the air temperature.
To ensure good thermal conductivity, the backside of the
LM26 die is directly attached to the GND pin (pin 2). The temperatures of the lands and traces to the other leads of the
LM26 will also affect the temperature that is being sensed.
Alternatively, the LM26 can be mounted inside a sealed-end
metal tube, and can then be dipped into a bath or screwed
into a threaded hole in a tank. As with any IC, the LM26 and
accompanying wiring and circuits must be kept insulated and
dry, to avoid leakage and corrosion. This is especially true if
the circuit may operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such
as Humiseal and epoxy paints or dips are often used to ensure
that moisture cannot corrode the LM26 or its connections.
The junction to ambient thermal resistance (θJA) is the parameter used to calculate the rise of a part's junction temperature due to its power dissipation. For the LM26 the equation
used to calculate the rise in the die junction temperature is as
follows:
TABLE 1. Resistive compensation for capacitive loading
of VTEMP
CLOAD
R (Ω)
≤100pF
0
1nF
8200
10nF
3000
100nF
1000
≥1µF
430
10132317
a) R in series with capacitor
(3)
where TA is the ambient temperature, V+ is the power supply
voltage, IQ is the quiescent current, IL_TEMP is the load current
on the VTEMP output, VDO is the voltage on the digital output,
and IDO is the load current on the digital output. Since the
LM26's junction temperature is the actual temperature being
measured, care should be taken to minimize the load current
that the LM26 is required to drive.
The tables shown in Figure 3 summarize the thermal resistance for different conditions and the rise in die temperature
of the LM26 without any loading on VTEMP and a 10k pull-up
resistor on an open-drain digital output with a 5.5V power
supply.
10132318
b) R in series with signal path
FIGURE 2. Resistor placement for capacitive loading
compensation of VTEMP
NOISE CONSIDERATIONS
The LM26 has excellent power supply noise rejection. Listed
below is a variety of signals used to test the LM26 power supply rejection. False triggering of the output was not observed
when these signals where coupled into the V+ pin of the
LM26.
• square wave 400kHz, 1Vp-p
• square wave 2kHz, 200mVp-p
• sine wave 100Hz to 1MHz, 200mVp-p
Testing was done while maintaining the temperature of the
LM26 one degree centigrade way from the trip point with the
output not activated.
SOT23-5
no heat sink
θJA
(°C/W)
θJA
TJ−TA
(°C)
(°C/W)
TJ−TA
(°C)
Still Air
250
0.11
TBD
TBD
Moving Air
TBD
TBD
TBD
TBD
FIGURE 3. Thermal resistance (θJA) and temperature rise
due to self heating (TJ−TA)
MOUNTING CONSIDERATIONS
The LM26 can be applied easily in the same way as other
integrated-circuit temperature sensors. It can be glued or ce-
www.national.com
SOT23-5
small heat sink
6
LM26
Typical Applications
10132303
Note: The fan's control pin has internal pull-up. The 10k pull-down sets a slow fan speed. When the output of the LM26 goes low, the fan will speed up.
FIGURE 4. Two Speed Fan Speed Control
10132320
FIGURE 5. Fan High Side Drive
10132321
FIGURE 6. Fan Low Side Drive
7
www.national.com
LM26
10132322
FIGURE 7. Audio Power Amplifier Thermal Protection
10132323
FIGURE 8. Simple Thermostat
www.national.com
8
LM26
Physical Dimensions inches (millimeters) unless otherwise noted
5-Lead Molded SOT-23 Plastic Package, JEDEC
Order Number LM26CIM5 or LM26CIM5X
NS Package Number MA05B
9
www.national.com
LM26 SOT-23, ±3°C Accurate, Factory Preset Thermostat
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage References
www.national.com/vref
Design Made Easy
www.national.com/easy
www.national.com/powerwise
Applications & Markets
www.national.com/solutions
Mil/Aero
www.national.com/milaero
PowerWise® Solutions
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors SolarMagic™
www.national.com/solarmagic
PLL/VCO
www.national.com/wireless
www.national.com/training
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2011 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated