ER3A thru ER3J SURFACE MOUNT SUPERFAST RECTIFIER CHENG- YI ELECTRONIC VOLTAGE RANGE -50 TO -600 VOLTS CURRENT -3.0 Amperes SMC/DO-214AB FEATURES For surface mounted applications Low profile package Built-in strain relief Easy pick and place Superfast recovery times for high efficiency Plastic package has Underwriters Laboratory Flammability Classification 94V-O Glass passivated junction High temperature soldering: 260oC/10 seconds at terminals .108(2.75) .128(3.25) .220(5.59) .245(6.22) .260(6.60) .280(7.11) .006(.152) .012(.305) .079(2.00) .103(2.62) MECHANICAL DATA .002(.051) .008(.203) .030(0.76) .050(1.27) Case: JEDEC DO-214AB molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard Packaging: 16mm tape (EIA-481) Weight: 0.007 ounces, 0.21 gram .305(7.75) .320(8.13) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, reistive or inductive load. For capacitive load, derate current by 20%. SYMBOLS ER3A ER3B ER3C ER3D ER3E ER3G ER3J UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 600 V Maximum RMS Voltage VRMS 35 70 105 140 210 280 420 V Maximum DC Blocking Voltage VDC 50 100 150 200 300 400 600 V Maximum Average Forward Rectified Current, at TL=75 C I(AV) 3.0 A Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 100 A Maximum Instantaneous Forward Voltage at 3.0A VF Maximum DC Reverse Current at Rated DC Blocking Voltage IR 0 @ TA=250C @ TA=1000C 0.95 1.25 5.0 TRR 35.0 Typical Junction Capacitance (Note 2) CJ 45.0 R Operating and Storage Temperature Range TJ , TSTG JL Notes : 1. Reverse Recovery Test Conditions: IF=0.5A, I R=1.0A, I RR=0.25A 2. Measured at 1.0 MHZ and Applied Vr=4.0 volts. 3. 8.0mm2 (.013mm thick) land areas. A 200 Maximum Reverse Recovery Time (Note 1) Maximum Thermal Resistance (Note 3) V 1.7 16 -50 to +150 nS pF 0 C/W 0 C ER3A thru ER3J SURFACE MOUNT SUPERFAST RECTIFIER CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES ER3A THRU ER3J 50 Noninductive (+) 25 Vdc (approx) ( ) trr 10 Noninductive +0.5A ( ) D.U.T. PULSE GENERATOR NOTE 2 1 NONInductive 0 -0.25 (+) OSCILLOSCOPE NOTE 1 -1.0 NOTES:1. Rise Time=7ns max. Input Impedance=1 megohm. 22pF 2. Rise Time=10ns max. Source Impedance=50 Ohms. 1cm SET TIME BASE FOR 10ns/cm AVERAGE FORWARD CURRENT, AMPERES Fig. 1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM ES1A THRU ES1G Fig. 2 - MAXIMUM AVERAGE FORWARD CURRENT RATING 3.0 2.5 2.0 1.5 SINGLE PHASE HALF W AVE 60HZ RESISTIVE OR INDUCTIVE LOAD P.C.B MOUNTED ON 0.315x0.315"(8.0x8.0mm) COPPER PAD AREAS 1.0 0.5 0 50 60 70 80 90 100 110 120 130 140 150 LEAD TEMPERATURE, oC Fig. 3 - TYPICAL REVERSE CHARACTERISTICS Fig. 4 - TYPICAL FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, AMPERES INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 1000 0 TJ=100 C 100 0 TJ=75C 10 1.0 0 TJ=25C 0.1 0.01 20 40 60 80 100 120 140 PERCENT OF RATED PEAK INVERSE VOLTAGE, VOLTS 100 ER3A-ER3D 10 ER3A-ER3G ER3J 1 0.1 0 TJ=25C PULSE WIDTH=300 S 2% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, VOLTS Fig. 6 - TYPICAL JUNCTION CAPACITANCE 100 200 0 TJ=25C f=1.0MHZ Vslg=50mVp-p 90 100 CAPACITANCE, pF PEAK FORWARD SURGE CURRENT, AMPERES Fig. 5 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 8.3ms SINGLE HALF SINCE-WAVE JEDEC METHOD 75 50 45 30 15 10 1 5 10 NUMBER OF CYCLES AT 60Hz 50 100 0.1 0.5 1 2 5 10 20 50 100 200 500 1000 REVERSE VOLTAGE, VOLTS