ES1A thru ES1J SURFACE MOUNT SUPERFAST RECTIFIER CHENG- YI ELECTRONIC VOLTAGE RANGE -50 TO -600 VOLTS CURRENT -1.0 Amperes SMA/DO-214AC FEATURES For surface mounted applications Low profile package Built-in strain relief Easy pick and place Superfast recovery times for high efficiency Plastic package has Underwriters Laboratory Flammability Classification 94V-O Glass passivated junction High temperature soldering: 260oC/10 seconds at terminals .055(1.40) .062(1.60) .098(2.50) .114(2.90) .157(4.00) .181(4.60) .006(.152) .012(.305) .078(2.00) .096(2.44) MECHANICAL DATA .002(.051) .008(.203) .030(0.76) .060(1.52) Case: JEDEC DO-214AC molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Indicated by cathode band Standard Packaging: 12mm tape (EIA-481) Weight: 0.002 ounces, 0.064 gram .188(4.80) .208(5.28) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 250C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, reistive or inductive load. For capacitive load, derate current by 20%. SYMBOLS ES1A ES1B ES1C ES1D ES1E ES1G ES1J UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 150 200 300 400 600 V Maximum RMS Voltage VRMS 35 70 105 140 210 280 420 V Maximum DC Blocking Voltage VDC 50 100 150 200 300 400 600 V Maximum Average Forward Rectified Current, at TL=120 C I(AV) 1.0 A Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30.0 A Maximum Instantaneous Forward Voltage at 1.0A VF Maximum DC Reverse Current at Rated DC Blocking Voltage IR 0 @ TA=250C @ TA=1000C 0.95 1.25 5.0 TRR 35.0 Typical Junction Capacitance (Note 2) CJ 10.0 R Operating and Storage Temperature Range TJ , TSTG JL Notes : 1. Reverse Recovery Test Conditions: IF=0.5A, I R=1.0A, I RR=0.25A 2. Measured at 1.0 MHZ and Applied Vr=4.0 volts. 3. 8.0mm2 (.013mm thick) land areas. A 100 Maximum Reverse Recovery Time (Note 1) Maximum Thermal Resistance (Note 3) V 1.7 35 -50 to +150 nS pF 0 C/W 0 C ES1A thru ES1J SURFACE MOUNT SUPERFAST RECTIFIER CHENG- YI ELECTRONIC RATING AND CHARACTERISTICS CURVES ES1A THRU ES1J Fig. 1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM ES1A THRU ES1G (+) 25 Vdc (approx) ( ) AVERAGE FORWARD CURRENT, AMPERES 50 Noninductive Fig. 2 - MAXIMUM AVERAGE FORWARD CURRENT RATING trr 10 Noninductive +0.5A ( ) D.U.T. 0 PULSE GENERATOR NOTE 2 1 NONInductive -0.25 (+) OSCILLOSCOPE NOTE 1 -1.0 NOTES:1. Rise Time=7ns max. Input Impedance=1 megohm. 22pF 2. Rise Time=10ns max. Source Impedance=50 Ohms. 1cm SET TIME BASE FOR 10ns/cm 1.0 25 50 75 100 125 150 175 Fig. 4 - TYPICAL FORWARD CHARACTERISTICS 10 INSTANTANEOUS FORWARD CURRENT, AMPERES 1000 IR-REVERSE LEAKAGE CURRENT, MICROAMPERES SINGLE PHASE HALF W AVE 60HZ RESISTIVE OR INDUCTIVE LOAD P.C.B MOUNTED ON 0.315x0.315"(8.0x8.0mm) COPPER PAD AREAS LEAD TEMPERATURE, oC Fig. 3 - TYPICAL REVERSE CHARACTERISTICS 0 TJ=125C 100 0 TJ=75C 10 0 TJ=25C 1.0 ES1A 1.0 ES1J ES1E 0.1 0 TJ=25C 0.01 0.001 0.1 20 40 60 80 10 0 0.2 120 0.4 0.6 0.8 1.0 1.2 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS % of PIV, VOLTS Fig. 6 - TYPICAL JUNCTION CAPACITANCE Fig. 5 - MAXIMUM NON-REPETITIVE SURGE CURRENT 14 JUNCTION CAPACITANCE, pF 30 PEAK FORWARD SURGE CURRENT, AMPERES 2.0 25 8.3ms SINGLE HALF SINCE-WAVE JEDEC METHOD 20 15 10 5 1 2 5 10 20 NUMBER OF CYCLES AT 60Hz 50 100 0 TJ=25C f=1.0MHZ Vslg=50mVp-p 12 10 8.0 6.0 4.0 2.0 0 0.1 1 10 REVERSE VOLTAGE, VOLTS 100